Tender For annual repair & maintenance of To Various Roads Under North Maintenance Zone, Pwd, Gnctd, Delhi During 2026-27 (Sh:- Upkeeping Of Entire Right Of Way (Row) (Excluding Main Carriageway) Of Shivdas Puri Marg (From Pusa Round About To Kirti N
Tender Value
36.60 Crore
Estimated cost
Bid Submission
06 Aug 2026
9 days left
EMD
46.60 Lakhs
Bank guarantee accepted
Document Fee
Ref. Documents
Non-refundable
Tender Type
Online
Tender Overview
Organization
Tender ID
Competition Type
NCB
Bidding Type
Tender
Location / State
Delhi → Delhi
EMD Exemption
Not Available
Quantity
Not Available
Website
Contact Person
Address
Project Description
Tender for annual repair & maintenance of To Various Roads Under North Maintenance Zone, Pwd, Gnctd, Delhi During 2026-27 (Sh:- Upkeeping Of Entire Right Of Way (Row) (Excluding Main Carriageway) Of Shivdas Puri Marg (From Pusa Round About To Kirti Nagar Cut), Road No. 41 & 41-A, Road No. 43 {From Orr To Haryana Maithri Bhawan, Haryana Maithri Bhawan To Fob, Fob To Raja Park Red Light (Ch. Balbir Singh Siddu Marg), Eklavya Marg Cut To Bss Marg Red Light, Britannia Chowk To Bss Marg Cut}, Dr. K.N. Katju Marg And Road No. 51 (Arihant Marg) Under North Maintenance Zone, Pwd, Delhi) - Composite Work (Civil & Electrical Works)
BOQ
| Sl. No. | Item Description |
| 1 | Comprehensive Maintenance (Part-A)Providing comprehensive cleaning, sweeping, washing, maintenance and upkeep services of Category–A urban road including carriageway edges, cycle tracks, footpaths, paved areas, street furniture, electrical fixtures (up to 8 m height), drainage system, litter bins, signage, structures, and complete corridor area, including deployment of required manpower such as sanitation staff, electricians and helpers, excluding horticulture works and security guards, including all labour, machinery, T&P, consumables, waste disposal, and all incidental charges, on per kilometre per month basis, as directed by Engineer-in-Charge. |
| 2 | Providing comprehensive cleaning, sweeping, washing, maintenance and upkeep services of Category–B urban road including cycle tracks, footpaths, paved/plaza areas, street furniture, electrical fixtures (up to 8 m height), drainage system, litter bins, signage, sculptures and complete corridor area, including deployment of required manpower such as sanitation staff, electricians, helpers and masons, excluding horticulture works and security guards, including all labour, machinery, T&P, consumables, waste disposal and all incidental charges, on per kilometre per month basis, as directed by Engineer-in-Charge. |
| 3 | Providing comprehensive cleaning, sweeping, washing, maintenance and upkeep services of Category–C urban road including footpaths, seating areas, street furniture, electrical fixtures (up to 8 m height), drainage system, litter bins and complete corridor area, including deployment of required manpower such as sanitation staff, electricians and helpers, excluding horticulture works and security guards, including all labour, machinery, T&P, consumables, waste disposal and all incidental charges, on per kilometre per month basis, as directed by Engineer-in-Charge. |
| 4 | Civil Component (Part-B)Earth work in excavation by mechanical means (Hydraulic excavator) / manual means in foundation trenches or drains (not exceeding 1.5 m in width or 10 sqm on plan), including dressing of sides and ramming of bottoms, for all lift, including getting out the excavated soil and disposal of surplus excavated soil as directed, within a lead of 50 m. All kinds of soil. |
| 5 | Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level : 1:1½:3 (1 Cement: 1½ coarse sand (zone-III) : 3 graded stone aggregate 20 mm nominal size).1:1½:3 (1 Cement: 1½ coarse sand (zone-III) : 3 graded stone aggregate 20 mm nominal size). |
| 6 | 1:3:6 (1 Cement : 3 coarse sand(zone-III) derived from natural sources : 6 graded stone aggregate 20 mm nominal size derived from natural sources). |
| 7 | Brick work with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in superstructure above plinth level up to floor V level in all shapes and sizes in :Cement mortar 1:6 (1 cement : 6 coarse sand) |
| 8 | Stone work, plain in copings, cornices, string courses and plinth courses, upto 75 mm thick in Cement mortar 1:6 (1 cement : 6 coarse sand) including pointing with white cement mortar 1:2 (1 white cement : 2 stone dust) with an admixture of pigment matching the stone shade. Red sand stone |
| 9 | Providing and fixing 18 mm thick gang saw cut, mirror polished, premoulded and prepolished, machine cut for kitchen platforms, vanity counters, window sills, facias and similar locations of required size, approved shade, colour and texture laid over 20 mm thick base cement mortar 1:4 (1 cement : 4 coarse sand), joints treated with white cement, mixed with matching pigment, epoxy touch ups, including rubbing, curing, moulding and polishing of edges to give high gloss finish etc. complete at all levels.Granite stone slab of colour black, Cherry/Ruby redArea of slab upto 0.50 sqm |
| 10 | Providing and fixing 18 mm thick gang saw cut, mirror polished, premoulded and prepolished, machine cut for kitchen platforms, vanity counters, window sills, facias and similar locations of required size, approved shade, colour and texture laid over 20 mm thick base cement mortar 1:4 (1 cement : 4 coarse sand), joints treated with white cement, mixed with matching pigment, epoxy touch ups, including rubbing, curing, moulding and polishing of edges to give high gloss finish etc. complete at all levels.Granite stone slab of colour black, Cherry/Ruby redArea of slab over 0.50 sqm. |
| 11 | Stone work (machine cut edges) for wall lining etc. (veneer work) upto 10 metre height, backing filled with a grout of average 12 mm thick cement mortar 1:3 (1 cement : 3 coarse sand) including pointing in white cement mortar 1:2 (1 white cement : 2 stone dust) with an admixture of pigment matching the stone shade : (To be secured to the backing and the sides by means of cramps and pins which shall be paid for separately) :Red sand stone - exposed face fine dressed with rough backing.40 mm thick |
| 12 | Providing and fixing Ist quality ceramic glazed wall tiles conforming to IS: 15622 (thickness to be specified by the manufacturer), of approved make, in all colours, shades except burgundy, bottle green, black of any size as approved by Engineer-in-Charge, in skirting, risers of steps and dados, over 12 mm thick bed of cement mortar 1:3 (1 cement : 3 coarse sand) and jointing with grey cement slurry @ 3.3kg per sqm, including pointing in white cement mixed with pigment of matching shade complete. |
| 13 | Providing and fixing hard drawn steel wire fabric 75x25 mm mesh of weight not less than 7.75 Kg per sqm to window frames etc. including 62x19 mm beading of second class teak wood and priming coat with approved steel primer all complete. |
| 14 | Providing and fixing ISI marked oxidised M.S. sliding door bolts with nuts and screws etc. complete (Copper oxidised as per IS 1378): 250x16 |
| 15 | Providing and fixing panelling or panelling and glazing in panelled or panelled and glazed shutters for doors, windows and clerestory windows (Area of opening for panel inserts excluding portion inside grooves or rebates to be measured). Panelling for panelled or panelled and glazed shutters 25 mm to 40 mm thick :Float glass panes: 5.0 mm thick glass panes (weight not less than 12.50 kg/sqm). |
| 16 | Providing and fixing aluminium tower bolts, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868 ) transparent or dyed to required colour or shade, with necessary screws etc. complete : 250x10 mm |
| 17 | Providing and fixing aluminium die cast body tubular type universal hydraulic door closer (having brand logo with ISI, IS : 3564, embossed on the body, door weight upto 35 kg and door width upto 700 mm), with necessary accessories and screws etc. complete. |
| 18 | Providing and fixing aluminium handles, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour or shade, with necessary screws etc. complete : 125mm |
| 19 | Providing and fixing Fiber Glass Reinforced plastic (FRP) Door Frames of cross-section 90 mm x 45 mm having single rebate of 32 mm x 15 mm to receive shutter of 30 mm thickness. The laminate shall be moulded with fire resistant grade unsaturated polyester resin and chopped mat. Door frame laminate shall be 2mm thick and shall be filled with suitable wooden block in all the three legs. The frame shall be covered with fiber glass from all sides. M.S. stay shall be provided at the bottom to steady the frame. |
| 20 | Providing and fixing to existing door frames.30 mm thick Glass Fibre Reinforced Plastic (FRP) panelled door shutter of required colour and approved brand and manufacture, made with fire - retardant grade unsaturated polyester resin, moulded to 3 mm thick FRP laminate for forming hollow rails and styles, with wooden frame and suitable blocks of seasoned wood inside at required places for fixing of fittings, cast monolithically with 5 mm thick FRP laminate for panels conforming to IS: 14856, including fixing to frames. |
| 21 | Providing and laying flamed finish Granite stone flooring in required design and patterns, in linear as well as curvilinear portions of the building all complete as per the architectural drawings with 18 mm thick stone slab over 20 mm (average) thick base of cement mortar 1:4 (1 cement : 4 coarse sand) laid and jointed with cement slurry and pointing with white cement slurry admixed with pigment of matching shade including rubbing, curing and polishing etc. all complete as specified and as directed by the Engineer-in-Charge : Black, Cherry Red, Elite Brown, Cat Eye or equivalent. |
| 22 | 12 mm cement plaster of mix: 1:6 (1 cement: 6 coarse sand) |
| 23 | Finishing walls with Acrylic Smooth exterior paint of required shadeOld work (Two or more coat applied @ 1.67 ltr./10 sqm) on existing cement paint surface |
| 24 | Finishing with Epoxy paint (two or more coats) at all locations prepared and applied as per manufacturer's specifications including appropriate priming coat, preparation of surface, etc. complete.On steel work. |
| 25 | Painting with synthetic enamel paint of approved brand and manufacture of required colour to give an even shade :One or more coats on old work |
| 26 | Providing, laying and making kerb channel 30 cm wide and 50 mm thick with cement concrete 1:3:6 (1 cement: 3 coarse sand:6 graded stone aggregate 20 mm nominal size) over 75mm bed of dry brick ballast 40 mm nominal size, well rammed and consolidated and grouted with fine sand, including finishing the top smooth etc. complete and as per direction of Engineer-in-charge. |
| 27 | Taking out existing kerb stones of all types from footpath/ central verge, including removal of mortar etc., disposal of unserviceable material to the dumping ground, for which payment shall be made separately and stacking of serviceable material within 50 metre lead as per direction of Engineer-in-Charge. |
| 28 | Taking out existing CC interlocking paver blocks from footpath/ central verge, including removal of rubbish etc., disposal of unserviceable material to the dumping ground, for which payment shall be made separately and stacking of serviceable material within 50 metre lead as per direction of Engineer-in-Charge. |
| 29 | Laying old cement cocrete interlocking paver blocks of any design/ shape laid in required line, level, curvature, colour and pattern over and including 50 mm thick compacted bed of coarse sand, filling the joints with fine sand etc. all complete as per the direction of Engineer-in-charge. (Old CC paver blocks shall be supplied by the department free of cost). |
| 30 | Laying at or near ground level old kerb stones of all types in position to the required line, level and curvature, jointed with cement mortar 1:3 (1 cement : 3 coarse sand), including making joints with or without grooves (thickness of joints, except at sharp curve, shall not be more than 5 mm), including making drainage opening wherever required etc. complete as per direction of Engineer-in-charge. (Length of finished kerb edging shall be measured for payment). (Old kerb stones shall be supplied by the department free of cost) |
| 31 | Providing and fixing 10x10x7.50 cm Granite stone block hand cut and chisel dressed on top, for paving in floors, drains etc. laid over 20mm thick base mortar 1:4 (1 cement : 4 coarse sand) with joints 10mm wide filled with same mortar including ruled pointing etc. complete as per direction of engineer-in-charge. |
| 32 | Providing and fixing water closet squatting pan (Indian type W.C. pan ) with 100 mm sand cast Iron P or S trap, 10 litre low level white P.V.C. flushing cistern, including flush pipe, with manually controlled device (handle lever) conforming to IS : 7231, with all fittings and fixtures complete, including cutting and making good the walls and floors wherever required:White Vitreous china Orissa pattern W.C. pan of size 580x440 mm with integral type foot rests |
| 33 | Providing and fixing white vitreous china pedestal type water closet (European type W.C. pan) with seat and lid, 10 litre low level white P.V.C. flushing cistern, including flush pipe, with manually controlled device (handle lever), conforming to IS : 7231, with all fittings and fixtures complete, including cutting and making good the walls and floors wherever required : W.C. pan with ISI marked white solid plastic seat and lid. |
| 34 | Providing and fixing white vitreous china flat back or wall corner type lipped front urinal basin of 430x260x350 mm and 340x410x265 mm sizes respectively with automatic flushing cistern with standard flush pipe and C.P. brass spreaders with brass unions and G.I clamps complete, including painting of fittings and brackets, cutting and making good the walls and floors wherever required :One urinal basin with 5 litre white P.V.C. automatic flushing cistern |
| 35 | Providing and fixing wash basin with C.I. brackets, 15 mm C.P. brass pillar taps, 32 mm C.P. brass waste of standard pattern, including painting of fittings and brackets, cutting and making good the walls wherever require:White Vitreous China Flat back wash basin size 550x 400 mm with single 15 mm C.P. brass pillar tap |
| 36 | Providing and fixing 8 mm dia C.P. / S.S. Jet with flexible tube upto 1 metre long with S.S. triangular plate to Eureopean type W.C. of quality and make as approved by Engineer - in - charge. |
| 37 | Providing and fixing white vitreous china wash basin including making all connections but excluding the cost of fittings :Flat back wash basin of size 450x300 mm |
| 38 | Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot &cold water supply, including all CPVC plain & brass threaded fittings, including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and testing of joints complete as per direction of Engineer in Charge.25 mm nominal dia Pipes |
| 39 | Providing and placing on terrace (at all floor levels) polyethylene water storage tank, IS : 12701 marked, with cover and suitable locking arrangement and making necessary holes for inlet, outlet and overflow pipes but without fittings and the base support for tank. |
| 40 | Providing and fixing C.P. brass angle valve for basin mixer and geyser points of approved quality conforming to IS:8931 : 15mm nominal bore |
| 41 | Providing and fixing PTMT bib cock of approved quality and colour. 15mm nominal bore, 86 mm long, weighing not lessthan 88 gms |
| 42 | Providing and fixing PTMT pillar cock of approved quality and colour. 15 mm nominal bore, 107 mm long, weighing not lessthan 110 gms |
| 43 | Providing and laying non-pressure NP2 class (light duty) R.C.C. pipes with collars jointed with stiff mixture of cement mortar in the proportion of 1:2 (1 cement : 2 fine sand) including testing of joints etc. complete :300 mm dia. R.C.C. pipe |
| 44 | Providing and fixing in position pre-cast R.C.C. manhole cover and frame of required shape and approved quality. H D - 20. Circular shape 560 mm internal diameter |
| 45 | Making connection of drain or sewer line with existing manhole including breaking into and making good the walls, floors with cement concrete 1:2:4 mix (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size) cement plastered on both sides with cement mortar 1:3 (1 cement : 3 coarse sand), finished with a floating coat of neat cement and making necessary channels for the drain etc. complete For pipes 250 to 300 mm diameter |
| 46 | Constructing brick masonry road gully chamber 50x45x60 cm with bricks in cement mortar 1:4 (1 cement : 4 coarse sand) including 500x450 mm pre-cast R.C.C. horizontal grating with frame complete as per standard design :With common burnt clay F.P.S. (non modular) bricks of class designation 7.5 |
| 47 | Providing and laying in position ready mixed or site batched design mix cement concrete for plain cement concrete work; using coarse aggregate and fine aggregate derived from natural sources, Portland Pozzolana/Ordinary Portland /Portland Slag cement, admixtures in recommended proportions as per IS: 9103 to accelerate / retard setting of concrete, to improve durability and workability without impairing strength; but excluding the cost of centering, shuttering and finishing as per direction of the engineer-in-charge; for the following grades of concrete.Note: In case the cement content in design mix is more than the minimum specified cement content, the contractor shall have discretion to either re-design the mix or bear the cost of extra cement.Concrete of M25 grade with minimum cement content of 300 kg /cum. |
| 48 | DSR 2023 correction factor is 0.973 as per OM 158/SE (TAS)/GST/2024/02-E dt.08/08/2024 |
| 49 | Providing and laying in position ready mixed or site batched design mix cement concrete for plain cement concrete work; using coarse aggregate and fine aggregate derived from natural sources, Portland Pozzolana/Ordinary Portland /Portland Slag cement, admixtures in recommended proportions as per IS: 9103 to accelerate / retard setting of concrete, to improve durability and workability without impairing strength; including laying, curing, carriage for all leads; but excluding the cost of centering, shuttering and finishing as per direction of the engineer-in-charge; for the following grades of concrete. Note: In case the cement content in design mix is more than the minimum specified cement content, the contractor shall have discretion to either re-design the mix or bear the cost of extra cement.All works upto plinth level :Concrete of M10 grade with minimum cement content of 220 kg /cum |
| 50 | Providing and laying in position ready mixed or site batched design mix cement concrete for plain cement concrete work; using coarse aggregate and fine aggregate derived from natural sources, Portland Pozzolana/Ordinary Portland /Portland Slag cement, admixtures in recommended proportions as per IS: 9103 to accelerate / retard setting of concrete, to improve durability and workability without impairing strength; including of laying, curing, carriage for all leads; but excluding the cost of centering, shuttering and finishing as per direction of the engineer-in-charge; for the following grades of concrete. Note: In case the cement content in design mix is more than the minimum specified cement content, the contractor shall have discretion to either re-design the mix or bear the cost of extra cement.All works upto plinth level Concrete of M25 grade with minimum cement content of 330 kg /cum |
| 51 | Add Cost Index @ 4.03% on DSR Items |
| 52 | Providing and fixing in position precast reinforced cement concrete vibro exposed RCC finished bollards of size 450mm dia and 850mm high duly compacted and fixed in concrete block of size 600x600x500 mm size with M-30 cement concrete as per approved by Engineer-in-Charge. The bollards should be casted in accurately moulds i/c reinforcement, excavation and disposal of excavated earth/malba complete as per the direction of Engineer-in-Charge.) |
| 53 | Providing and laying kota stone cobbel flooring of size 150x150 mm and 70mm to 80mm thick laid over 20mm (avg.) thick base of cement mortar 1:3 (1 cement: 3 Coarse sand) of approved design/shape and jointed and pointed with cement mortar 1:3 (1 cement : 3 coarse sand) of average 10mm thick joints etc. complete as per direction of Engineer-in-Charge... |
| 54 | Providing and laying kota stone cobel flooring of size 100x100x75 mm (average) thick laid over 20mm (avg.) thick base of cement mortar 1:3 (1 cement: 3 Coarse sand) of approved design/shape and jointed and pointed with cement mortar 1:3 (1 cement: 3 coarse sand) of average 10mm thick joints etc. complete as per direction of Engineer-in-Charge.) |
| 55 | D.Q stone/hard stone floiring of size 150x150x75mm (average) thick laid over 20mm (avg) thick base of cement mortar 1:3 (1 cement 3 coarse sand) of approved design/shape jointed and pointed with cement mortar 1:3 (1 cement: 3 coarse sand) of average 10mm thick joints etc. complete as per direction of Engineer-in-Charge |
| 56 | Providing and fixing factory made precast RCC perforated drain covers, having concrete of strength not less than M-30, of size 550 x 500x50 mm, reinforced with 8 mm dia four nos longitudinal & 9 nos cross sectional T.M.T. hoop bars, including providing 50 mm dia perforations @ 100 to 125 mm c/c, including providing edge binding with M.S. flats of size 50 mm x 1.6 mm complete, all as per direction of Engineer-in-charge. |
| 57 | Providing and laying Polyurethane (PU) based 5-pack coating system (Resin, Hardener, Anti-moisture paste, Filler and Pigment paste) on prepared surface of cycle track, including mechanical cleaning of surface, crack filling (if required), application of primer, intermediate and top coats, proper mixing in specified proportions, curing, finishing to required texture, to achieve a total thickness of 2.0 mm to 2.5 mm, complete as per manufacturer’s specifications and direction of Engineer-in-Charge. Colour shall be as approved by Engineer-in-Charge. (On Concrete Surface) |
| 58 | Providing & Fixing M.S. Bollard with 900mm height including the groove size of 50mm with 3mm MS sheet and 3nos. of 40x40x5mm angle of length 850mm after applying a coat of steel primer etc. Complete as per direction of Engineer In-charge. (drawing as approved by consultant) |
| 59 | Precasting and placing in position 200X200 mm sqr Bollards 1000 mm high of required shape including reinforcement wth Thermo-mechanically-treated bar as required and embedded 150mm in cement concrete 1:3:6 (1 Cement : 3 coarse sand (zone-III) : 6 graded stone aggregate 20 mm nominal size), including necessary excavation of size 350x350x450mm deep for the same in bitumen/concrete pavement at specified spacing. |
| 60 | Providing and fixing FRP recessed type (flush with surrounding surface) manhole cover with frame of required shape and size, of approved make and quality, in cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate of 20 mm nominal size) over existing manholes, including surface preparation, placing, centering, curing and all incidental works, complete as per direction of Engineer-in-Charge, light duty (5 tonne capacity), of size 750 mm × 750 mm with variable deep recess (The size may be varry from site to site-therefore the agency is bound to fix as per site condition), with provision to adjust/modify the manhole and recess dimensions to suit site conditions and finished levels, the cover being lightweight, flush with adjacent surface, suitable for filling with matching surface material, and designed for pedestrian movement only (not for vehicular traffic). |
| 61 | Providing and laying fectory made texture finish paver block 400x400x60mm ( light grey, dark grey and black), in combination of 100x100x60mm ( light grey, dark grey and black),in required pattern as per drawing over 20mm thick base of cement mortar 1:4 ( 1 cement : 4 coarse sand ) laid and jointed with cement slurry in footpath parks,lawn,drive ways or light traffic parking etc. complete as per manufacture's specification and direction of Engineer-in- Charge. |
| 62 | Providing and fixing 600x600x100 mm pre-cast R.C.C horizontal grating having Single layer of 12mm dia torr steel at 100mm c/c complete as per standard design: |
| 63 | Providing and fixing in position 150 x150 mm Red Sand Stone Bollards 900 mm high of required/Approved shape & Size , including necessary excavation of size 250x250x450mm deep for the same in bitumen/ concrete pavement at specified spacing complete as per direction of consultant/ Engineer-in-Charge. |
| 64 | Precasting and placing in position India Gate type bollard of approved design, having overall height of 1760 mm, base size 300 mm × 300 mm and tapering to octagonal shape at top with 90 mm side, manufactured using M-30 grade cement concrete, complete as per approved drawings and direction of Engineer-in-Charge. The bollard shall include embedding of one GI pipe of 225 mm length and 65 mm internal diameter centrally, as required. The bollard shall be fixed in position by embedding 150 mm into cement concrete 1:3:6 (1 cement : 3 coarse sand (Zone-III) : 6 graded stone aggregate of 20 mm nominal size), including necessary excavation of size 350 mm × 350 mm × 450 mm deep in existing bituminous / concrete pavement, disposal of excavated material, refilling, compaction and making good the surface complete as per direction of Engineer-in-Charge. |
| 65 | Providing and laying at or near ground level factory made Vibro compacted cement concrete kerb stone of M-35 grade concrete made up in fully automated plant with steel moulds resulted in precise dimensions with compaction @ 3200 psi including minimal water ratio content (3:1) with water less curing by Ratho curing system in position to the required line, level and curvature , jointed with mortar 1:3 including making joints with or without grooves (thickness of joints except at sharp curve shall not to more than 5mm), including making drainage opening wherever required complete etc. as per direction of Engineer-in-charge (length of finished kerb edging shall be measured for payment). (Precast C.C. kerb stone shall be approved by Engineer-in-charge). |
| 66 | Providing and fixing FRP Gully Grating (flush with surrounding surface) manhole cover with frame of required shape and size, of approved make and quality, in cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate of 20 mm nominal size) over existing manholes, including surface preparation, placing, centering, curing and all incidental works, complete as per direction of Engineer-in-Charge, heavy duty (20 tonne capacity), of size 300 mm × 450 mm as per direction of Engineer-in-Charge. |
| 67 | Providing and laying Vibro compacted cement concrete Kerb Channel of M-35 grade concrete made up in fully autoamated plant with steel moulds resulted in precise dimensions with compaction @ 3200 psi including minimal water ratio content (3:1) with waterless curing by Rotho curing system to be laid in line, level and curvature, jointed with cement mortar 1:4 (1cement : 4 coarse sand ), including making joints with or without grooves (thickness opf joints at sharp curve shall not more than 5mm , including making drainage opening wherever required complete etc. as per direction of engineer-incharge ( length of finished kerb channel shall be measured for payment). |
| 68 | Providing and laying factory made vibro compacted cement concrete paver blocks of size 200x100x80 mm of M-35 grade concrete made up in fully automated plant with steel moulds resulted in precise dimensions with compaction @ 3200 psi including minimal water ratio content (3:1) with waterless curing by Ratho curing system , laying in cement mortar 1:4(1 cement : 4 coarse sand) and filling joint with special grout & required shade etc. all complete as per direction of Engineer-in-Charge. |
| 69 | Providing and laying factory made texture finish paver block 400x400x60mm ( light grey, dark grey and black), in combination of 100x100x60mm ( light grey, dark grey and black),in required pattern as per drawing over 20mm thick base of cement mortar 1:4 ( 1 cement : 4 coarse sand ) laid and jointed with cement slurry in footpath parks,lawn,drive ways or light traffic parking etc. complete as per manufacture's specification and direction of Engineer-in- Charge. |
| 70 | Providing and laying CC tactile tile (for vision impaired persons as per standards) of size 300x300x20mm having water absorption less than 0.5% and conforming to IS: 15622, of approved make in all colours and shades in outdoor floors such as footpath, court yard, multi modals location etc., laid on 20mm thick base of cement mortar 1:4 (1 cement : 4 coarse sand) in all shapes & patterns including grouting the joints with white cement mixed with matching pigments etc. complete as per direction of Engineer-in- Charge. |
| 71 | Providing and laying tactile tile of Jaisalmer stone (for vision impaired persons as per standards) of size 300x300x10mm having water absorption less than 0.5% and conforming to IS: 15622, of approved make in all colours and shades in outdoor floors such as footpath, court yard, multi modals location etc., laid on 20mm thick base of cement mortar 1:4 (1 cement : 4 coarse sand) in all shapes & patterns including grouting the joints with white cement mixed with matching pigments etc. complete as per direction of Engineer-in- Charge. |
| 72 | Providing and Fixing Ceramic Glazed wall tiles(600X300) 5 mm thick in sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and confirming to IS : 15622 of approved make in all colours and shades in facia and drops of width upto 200mm over 12 mm thick cement mortar 1:3 (1 cement : 3 coarse sand) with apoxy resin based adhesive including grouting the joits with special grout of required shade etc. complete as per the direction of Engineer-in-Charge. |
| 73 | Providing and laying rectified mat finished / antiskid floor tiles of size 97X97X20 mm of 1st quality conforming to is: 4457/2007 of approved make in colours, laid on 20 mm thick cement mortar 1:4 (1cement : 4 coarse sand) including grouting the joints with white cement and matching pigments etc., complete. (Flamed Biege & flamed black) complete as per direction of Engineer-in- Charge. |
| 74 | Providing and laying rectified mat finished / antiskid floor tiles of size 97X97X20 mm of 1st quality conforming to is: 4457/2007 of approved make in colours, laid on 20 mm thick cement mortar 1:4 (1cement : 4 coarse sand) including grouting the joints with white cement and matching pigments etc., complete. (Flamed Biege & flamed black) complete as per direction of Engineer-in- Charge. |
| 75 | Providing and laying factory made vibro compacted cement concrete solid blocks of M-10 grade made up in fully automated plant with steel moulds resulted in precise dimensions with compaction @ 3200 psi including minimal water ratio content (3:1) with water less curing by Ratho curing system, masonry with any size blocks in foundation and upto plinth lavel with cement mortar(1:4) all complete as per direction of Engineer-in-Charge. |
| 76 | Stone work gang saw cut (polished and machine cut) for wall lining (veneer work) backing field with a grout of average 12 mm thick in cement mortar 1:3 (1 cement : 3 coarse sand), including pointing with special grout of required shade to macth the granite shade ( To be secured to the backing by means of cramps which shall be paid for saparately) |
| 77 | 40mm thick Kota stone (Shot Blosted) slab flooring over 20 mm (average) thick base laid over and jointed with grey cement slurry mixed with pigment to match the shade of the slab complete with base of cement mortar 1 : 4 (1 cement : 4 coarse sand) : Kota stone Slabs 22\\"x22\\" Size and variable size as per site condtion and direction of Enginner-in-Charge. |
| 78 | 40 mm thick Kadappah stone Slab (Shot Blosted) stone slab flooring over 20 mm (average) thick base laid over and jointed with grey cement slurry mixed with pigment to match the shade of the slabcomplete with base of cement mortar 1 : 4 (1 cement : 4 coarse sand) : kadappah stone Slabs 22\\"x22\\" Size and variable size as per site condition and direction of Enginner-in-Charge. |
| 79 | 40 mm thick rubbed stone flooring (Shot Blasted) stone slab flooring over 20 mm (average) thick base laid over and jointed with grey cement slurry mixed with pigment to match the shade of the slabcomplete with base of cement mortar 1 : 4 (1 cement : 4 coarse sand).Red sand stone/Yellow sand stone - Slabs 22\\"x22\\" Size and variable size as per site condtion and direction of Enginner-in-Charge. |
| 80 | Electrical Component (Part-C)Providing and fixing following rating and breaking capacity and pole MCCB with thermomagnetic release and terminal spreaders in existing cubicle panel board including drilling holes in cubicle panel, making connections, Ics=100% Icu and Operational Voltage 690V etc. as required.125 A, 16 KA,TPMCCB |
| 81 | 1:3:6 (1 Cement : 3 coarse sand (zone-III) drived from natural sources : 6 graded stone aggregate 20 mm nominal size drived from natural sources) |
| 82 | 1:4:8 (1 Cement : 4 coarse sand (zone-III) drived from natural sources : 8 graded stone aggregate 40 mm nominal size drived from natural sources) |
| 83 | Earthing with G.I. earth pipe 4.5 meter long, 40 mm dia including accessories, and providing masonry enclosure with cover plate having locking arrangement and watering pipe etc. with charcoal/ coke and salt as required. |
| 84 | Providing and fixing 25 mm X 5 mm G.I. strip in 40 mm dia G.I. pipe from earth electrode including connection with G.1. nut, bolt, spring, washer excavation and re-filling etc. as required. |
| 85 | Providing and fixing 25 mm X 5 mm G.I. strip on surface or in recess for connections etc. as required. |
| 86 | Providing and fixing 6 SWG dia G.I. wire on surface or in recess for loop earthing along with existing surface/ recessed conduit/ submain wiring/ cable as required. |
| 87 | LED Batten light (System lumen efficacy ≥105 <120 lm/Watt). Supplying, Installation, Testing & Commissioning of LED surface mounted Batten light of following body material and construction as per IS : 10322 with driver (Replaceable) as per the requirement with Driver efficiency >85%, Operating voltage AC 140270 Volt, frequency 50/60 hz, Operating temp range -5 °C to 40 °C, internal surge protection of 2.5 KV with Short & Open circuit protection, THD < 10%, P. F.≥0.95, IP20, CRI >80, Flicker free, (flicker should be below 5 %), life time (LED, Driver & electrical circuitry), of minimum 50000 Burning Hours with 70% of initial Lumen maintained till life ends, CCT 3000°K / 4000°K / 5700°K /6500°K (As per ANSI Bin), SDCM(Standard Deviation Colour Matching) <3, Maximum power consumption should not more than the specified rating and Fixture shall be of relevant BIS standard. Manufactures Word Mark/ Name Engraved/ Embossing/ Screen printing on housing. complete in all respect i/c external connections with 1.5 sq mm FRLS/HFFR, PVC insulated copper conductor single core cable and earthing etc. as required with Minimum 5 year OEM warranty. System lumen efficacy ≥105 <120 lm/Watt output . LM79 & LM80 Test report and all testing required for LED fixtures as per BIS shall be submitted. Shape size and CCT shall be as approved by Engineer-inCharge as per requirement. (Thermal management: heat sink of aluminium housing such that LED junction temperature shall not rise above 90°C). Powder coated die cast /Extruded aluminium Body (Thickness > 1.20 mm) |
| 88 | Laying of one number PVC insulated and PVC sheathed / XLPE power cable of 1.1 KV grade of following size in the existing RCC/ HUME/ METAL pipe as required.Upto 35 Sq.mm |
| 89 | Supplying and making end termination with brass compression gland and aluminium lugs for following size of PVC insulated and PVC sheathed / XLPE aluminium conductor cable of 1.1 kV grade as required.4 x 16 sq. mm (28mm) |
| 90 | 4 x 25 sq. mm (28mm) |
| 91 | Excavation for cable trenches in soft soil, of reqd depth & width including getting out the excavated soil, refilling with excavated soil or good soil after laying of cable/ pipe (but excluding laying of cable & pipe) etc.and disposal of surplus excavated soil as directed, within a lead of 50 meter. |
| 92 | Demolishing cement concrete manually/ by mechanical means including disposal of material within 50 metres lead as per direction of Engineer - in - charge.Nominal concrete 1:3:6 or richer mix (i/c equivalent design mix) |
| 93 | Nominal concrete 1:4:8 or leaner mix (i/c equivalent design mix) |
| 94 | Excavation for cable trenches in soft soil, depth upto 1.2 m including dressing of sides lift upto 1.5 m, including getting out the excavated soil, refilling with sand and or good soil after laying of cable/ pipe etc in layers of 20 cm, ramming, watering and disposal of surplus excavated soil as directed, within a lead of 50 metres. |
| 95 | Supplying and laying of following size DWC HDPE pipe ISI marked along with all accessories like socket, bend, couplers etc. conforming to IS 14930, Part II complete with fitting and cutting, jointing etc. in the existing trench, complete as required. 63 mm dia (OD-63 mm & ID-51 mm nominal) |
| 96 | Supplying and laying of following size DWC HDPE pipe ISI marked along with all accessories like socket, bend, couplers etc. conforming to IS 14930, Part II complete with fitting and cutting, jointing etc.direct in ground (75 cm below ground level) includingexcavation and refilling the trench but excluding sand cushioning and protective covering etc., complete as required.63 mm dia (OD-63 mm & ID-51 mm nominal) |
| 97 | Disposal of building rubbish / malba / similar unserviceable, dismantled or waste materials by mechanical means, including loading, transporting, unloading to approved municipal dumping ground or as approved by Engineer-in-charge, beyond 50 m initial lead, for all leads including all lifts involved. |
| 98 | Providing, laying, testing & commissioning of 'B' class medium duty G.I. pipe conforming to IS 1239 including welding, fittings like elbows, tees, flanges, tapers, nuts, bolts, gaskets etc. and fixing the pipe on the wall/ceiling with suitable clamp/support frame and painting with two or more coats of synthetic enamel paint of required shade complete as required :80 mm |
| 99 | Supplying and Fixing of 7.5 Mtrs Decorative Street light pole and suitable for double arm G.I. bracket for hanging Decorative lights with galvanised mild steel tubes with cast aluminium embellishments X 4 and the pole base the size of base 450 mm x 490 mm diecastaluminium suitable for 140 mm OD steel pole bottom dia 114 mm and height 6000 mm dia cast aluminium and weight of pole base not less than 55 kgs. suitable for 140 mm OD pipe having following specification. The pole have at bottom profile (140 mm dia x 4 mm x 1000 mm height) including with cast aluminium embellishment to decorative pole and middle profile (114 mm dia x 4 mm x 2500 mm height) and top profile size of embellishment not less than 370 mm H (90mm x 3 mm x 2000 mm height) achieving total height 7 mtr. with base plate 300 x 300 x 12 mm welded at bottom of the pole base plate. The pole are primer coated and painted with polyurethane paint (PU Paint) DFT not less than 90 micron. The pole has a service window with sleeve type theft proof window cover with at the bottom comprising four way 32Amp. Terminal Connector and connection alongwith MCB and 2.5 Sq.mm Copper conductor Cable. The Pole can be mounted with four numbers anchor bolts on existing foundation complete etc as required at site. (As per attached Drawing) (All dimensions are with production tolerance of ±3%) |
| 100 | Providing, fabricating, supplying, erecting, testing and commissioning of Y-shaped Mild Steel (MS) Pole of approximately 5.0 metres height, fabricated from suitable MS sections complete with Y-type bracket for mounting of LED street light luminaires, including base plate, anchor bolts, foundation hardware, welding, grinding, surface preparation, application of one coat of zinc chromate/red oxide primer and two coats of Polyurethane (PU) paint of approved shade, complete with all necessary nuts, bolts, clamps, accessories and fixing arrangements as required for complete installation. |
| 101 | S/I/T/C of 4 Mtr architectural column light made of mild steel with overall height would be 4000mm duly finished with desired PU paint. Light column in square cross section made of mild steel housing components in square cross section including a laser profile jail pattern (~2.4 m ht of MS laser cut sheet 2.5mm), gladded with opal acrylic diffuser, 4Nos 20W LED source and additional Post top head of 4X18W LED, Black in Colour, coated for high corrosion resistance, silicone gasket, SS fasteners, foundation bolt integral driver, IP65, for the complete light fixture including non-metallic portion; and installation accessories. 360 deg light distribution in the column part provided and low glare indirect line of vision. Efficacy > 85% , THD <10%, PF>0.9, > 4kV.CCT 3000K, CRI>70, SDCM<4 & IK>07; Life of LED – 50,000 burning hours. Cross-section ~225 X 225 mm; MS sheet. Pre-wired, with earth connection, Integral Junction chamber for cable termination with 4way 32 Amp heavy duty connector MCB etc. as reqd. |
| 102 | Dismantling of existing Architectural Light Column, removal of damaged polycarbonate sheets, LED modules/linear fixtures, LED drivers, internal wiring and other defective accessories; surface preparation by grinding/sanding, application of one coat epoxy metal primer followed by two coats of exterior grade PU paint of approved shade; providing and fixing new UV-stabilized translucent polycarbonate sheets (minimum 4–6 mm thick), new IP-65 LED illumination system complete with LED drivers, FRLS internal wiring, connectors, terminal blocks and all accessories; reassembly, transportation (if required), reinstallation in original position, testing, commissioning and making good complete, including all labour, scaffolding/manlift, T&P, consumables, fasteners and incidentals as required. including rodent-proof G.I./Stainless Steel wire mesh at all cable entry points and other openings of the Architectural Light Column/Portal Frame to prevent entry of rodents, complete with necessary clamps, fasteners and sealant as required..The lumen output of the LED shall be equal to that of the existing Lumneries the LED module and driver shall be covered by a comprehensive 5 year warranty from the OEM.2 Mtr. Height Pole |
| 103 | 3 - 3.5 Mtr. Height |
| 104 | Dismantling of existing Illuminated Architectural Steel Portal (gateway) Frame of approved dimensions including shifting to workshop/site as required, repairing of MS structural members by welding, grinding and straightening wherever required, replacement of damaged perforated MS panels (where required), removal of damaged LED linear fixtures/modules, LED drivers, internal FRLS wiring and accessories. Providing and fixing new IP-65 LED linear lighting system complete with aluminium profiles, LED drivers, internal wiring, connectors and all accessories. Surface preparation by mechanical cleaning, application of one coat epoxy metal primer followed by two coats of exterior grade PU paint of approved shade and make. Reassembly, transportation, erection/reinstallation in original position, tightening of anchor bolts, testing, commissioning and making good complete, including all labour, T&P, scaffolding/hydraulic platform, consumables and all incidental works as required. including rodent-proof G.I./Stainless Steel wire mesh at all cable entry points and other openings of the Architectural Light Column/Portal Frame to prevent entry of rodents, complete with necessary clamps, fasteners and sealant as required..The lumen output of the LED shall be equal to that of the existing Lumneries the LED module and driver shall be covered by a comprehensive 5 year warranty from the OEM. |
| 105 | Dismnatling of existing Foundation of 4 Mtr architectural column light/ 9 mtr pole side lane by hammer vibration machine and Disposal of malba, dismantled or waste materials including loading, transporting, unloading to approved municipal dumping ground or as approved by Engineer-in-charge,etc as required |
| 106 | Supplying and Fixing of Decorative ornamental Double arms brackets Height of Bracket (1500 mm x 500 mm) & (minimum weight 25 Kg) overhang each side made out of GI pipes with decorative cast aluminium embellishment as per drawing. Brackets are primer coated and painted with polyurethance paint suitable for decorative hanging light fitting etc as reqd. at site. (All dimensions are with production tolerance of ±3%) |
| 107 | Supplying, Installation, testing and commissioning of Decorative LED fitting 120 Watt. (Height of the fixture 625 mm x 630 mm) made out of spun aluminium body, clear PMMA / PC diffuser with power LED's are mounted directly on extruded aluminium heat sink and Electronic Driver i/c connection complete etc as reqd. at site. (All dimensions are with production tolerance of ±3%) |
| 108 | Supply and fixing of architectural column light accessories for 4 Mtrs pole(2.4 Mtrs designer column light side) such as integral driver ,IP 65,IK > 07for the complete light fixture including laser cut mild steel 2.5 mm thick duly polyurethane painted ,36 W LED Tube light,18 watt LED module with driver and external SPD ,3 mm thick frosted PUMMA Sheet for making 4 mtr architectural light functional, suitable for approx. 3000mm long x 200 mm width (NS) as per direction of Engineer in charge. |
| 109 | Supplying and drawing following sizes of PVC insulated copper conductor multicore cable in the existing poles and bracket from cable termination connector to the fitting i/c providing suitable copper lugs connections complete i/c credit / buyback for old dismantled material i/c dismantling as on where it is basis etc complete as required .3 core x 1.5 sq. mm |
| 110 | Repairing of 12 Mtr/ 10 mtr/ 8 mtr/ 5 Mtr. long Pole window i/c disconnection of existing cable and dressing of cable, thimbling and taping as per actual requirement in each window, providing and fixing 63 Amp 4 pole stud terminal connector, refixing of dressed cable etc. with the help of ladder complete as reqd. |
| 111 | Providing and lying in position M-20 (1:2:4) reinforced cement concrete foundation of size 600 mm (L) x 600 mm (W) and 1500 mm (D) i/c excavation of earth, providing cutting, bending and placing in position, reinforcement TMT bars of 12 mm dia 1600 mm long (approx.)-8 nos. and reinforcement ring of cold twisted bar of 8 mm dia-2800 mm (approx.)-10 nos. (with 150 mm spacing) as required with positioning of 4 Nos. foundation anchar bolts and providing 90 mm (O.D.) DWC, HPDE pipe for cable entry and exit as required. |
| 112 | Fabricating, supplying and fixing of wire mesh protection frame work fabricating with 40 x 40 x 6 mm thick angle iron/Tee iron having intermediate members of size 25mm x 6 mm flat strip welded at 30 cm in each sections horizontally & duly welded with hard drawn wire fabric mesh of size 25 mm X 75 mm (GI wire should be 6SWG) having weight not less than 7.5 Kg/Sqmtr. and making main door gate provided with two nos. sliding bolt with 02 nos. godown inter locks with operating hadle welded from inside of the door i/c providing and fixing of four no. legs of same angle size of 90 cm length duly grouted in foundation (30 x 30 x 45) cm (deep) in 1:2:3 cement concrete & painting with one coat of red oxide & two coat of super synthetic luminous paint of approved colour and quality etc. complete as complete as reqd. {Area of hard drawn wire fabric with angle (Except legs) shall be measured for payment} |
| 113 | Fabrication, Supplying and installation of outdoor type cubical feeder pillar of suitable size not less than 400mm deep made out of M.S. sheet 2mm thick (14 SWG) duly compartmentalised having 300 amp, 4 strip aluminium busbars with heat shirikable coloured sleeves and DMC/SMC busbar supports etc double door with two nos. godown locking arrangement for protection from rain, dust, duly fixed on M.S. angle iron frame work of size 50 mm X 50 mm X 6 mm (NS) 120 cm long legs out of which 45 cm duly grouted in cement concrete 1:2:4 (1 cement 2 sand :4 stone aggregate 20 mm) and having following accessories mounted inside the cubical panel i/c connection, inter connection with aluminum thimbles, earthing with two nos. earth studs duly painted with one coat of red oxide & two coats of superior quality enamel paint complete etc. as reqd. Supplying & Fixing of following accessorries in the existing cubical panel board/feeder pillar including connection testing etc. as reqd. (For Street Light Poles) (Size Not less than 1.3 Sqm) (Note:- inside the panel the space for three phase energy meter must be present).INCOMER160A FP 25KA MCCB with Thermal Magnetic Base for O/L & S/CProtection.- 1 No.Extended Rotatory Handle, Spreaders - 1 No.6A SP 10KA MCB - 3 Nos.Digital VAF Meter- 1 No.R,Y, B Indication Lamps - 3 Nos.CT's 200/5A, 15 VA, CL-1.0 - 3 Nos.BUS BAR200A TPN ALU BUS BAROUTGOING125A FP 25KA MCCB with Thermal Magnetic Base for O/L & S/C Protection. - 2 Nos.Extended Rotatory Handle, Spreaders - 2 Nos.100A FP 25KA MCCB with Thermal Magnetic Base for O/L & S/C Protection. - 1 No.Extended Rotatory Handle, Spreaders - 1 No.160A FP AC1 Power Contactor (2NO + 2NC) - 1 NoAstronomical Timer Swith - 1 NoAutomanual Selector Switch - 1 No6A SP 10KA MCB - 1 NoON/OFF Indicating Lamps - 2 NosStart/Stop Push Button - 2 Nos (Note:- Their Must be separate space for energy meter) |
| 114 | Providing, Supplying, Installation, Testing & Commissioning of decorative umbrella-shaped LED Post Top Luminaire 40 Watt having die-cast aluminium housing with round aluminium casted ring supported by spokes, designed for uniform downward and surrounding light distribution, complete with UV stabilised laser-cut clear/opal PMMA diffuser for glare-free illumination, IP66 protected optical compartment, powder coated with UV stabilised polyester powder coating, equipped with high efficiency LED modules suitable for 40 Watt, make to be approved by Engineer-in-Charge.(Luminaire having system efficacy not less than 110 lm/W, CRI ≥ 70, available in CCT 3000K/5700K, operating voltage range 110V–290V AC, power factor ≥ 0.90, THD < 20%, with inbuilt surge protection up to 4 kV, complete with all accessories.The fitting shall be suitable for mounting on pole top of diameter 48 mm to 60 mm including all necessary clamps, connectors, hardware, internal wiring, earthing, and fixing arrangements.Complete as required for application in garden lighting, landscaping areas, commercial complexes and boundary wall illumination.) |
| 115 | Supply, installation, testing and commissioning of Decorative Urban Post Top LED Luminaire (Victoria type), 60W, suitable for heritage/victorian post top mounting, comprising of die-cast/spun aluminium housing duly powder coated with UV stabilised polyurethane paint, having separate optical compartment with IP-66 protection. The luminaire shall be provided with UV stabilised clear PMMA diffuser, properly sealed to ensure long lasting IP-66 ingress protection. The fitting shall be complete with control gear plate, SMD LED module, constant current electronic driver and all required electrical accessories.The luminaire shall be compatible for mounting on pole top of 48 mm to 60 mm diameter. The LED shall be of reputed make such as Osram/Seoul/Bridgelux or equivalent, with system wattage of 60W (suitable replacement of conventional 70W fitting), having minimum efficacy of 100 lm/W and CRI ≥ 70. The luminaire shall have Correlated Colour Temperature (CCT) of 3000K / 5700K as required.The driver shall operate within input voltage range of 110V to 290V AC, power factor ≥ 0.9, THD ≤ 20%, and shall be provided with surge protection of minimum 4 kV (10 kV SPD optional if required). Complete as required at site and direction of Engineer-in-Charge. |
| 116 | ismantling, repairing, refurbishing, repainting and reinstallation of existing 5.0 metre high Height Visual Marker complete, comprising dismantling of the existing visual marker including all internal accessories, shifting to workshop (if required), removal and disposal of damaged polycarbonate sheets, LED luminaires, LED drivers, wiring and other defective components. Providing and fixing new UV stabilized translucent polycarbonate sheets of approved make and thickness (minimum 4-6 mm) on all illuminated faces, complete with necessary aluminium/SS sections, EPDM rubber gaskets, SS screws, silicone sealant etc. as required. Providing and fixing IP-65 LED linear lighting system inside the marker consisting of high efficiency LED modules/LED strips with aluminium profile, electronic constant voltage/current LED drivers, internal FRLS copper wiring, connectors, terminal blocks and all necessary accessories for uniform illumination of all faces. Surface preparation by removing existing damaged paint, rust, dust and loose material by sanding/grinding, applying one coat epoxy metal primer followed by two coats of exterior grade Polyurethane (PU) paint of approved shade and make on all exposed MS surfaces to achieve smooth and uniform finish. Re-assembling, transportation back to site, erection/reinstallation of the visual marker in its original position including alignment, anchoring, tightening of all fasteners, testing, commissioning and trial run complete as required. The item includes all labour, T&P, scaffolding/manlift, transportation, loading/unloading, consumables, fasteners, wiring, connectors and all incidental works complete. including rodent-proof G.I./Stainless Steel wire mesh at all cable entry points and other openings of the Architectural Light Column/Portal Frame to prevent entry of rodents, complete with necessary clamps, fasteners and sealant as required.The lumen output of the LED shall be equal to that of the existing Lumneries the LED module and driver shall be covered by a comprehensive 5 year warranty from the OEM. |
| 117 | Dismantling, repairing, refurbishing, repainting and reinstallation of existing 3.0-3.5 metre high Height (Width 15 Inch) Visual Marker complete, comprising dismantling of the existing visual marker including all internal accessories, shifting to workshop (if required), removal and disposal of damaged polycarbonate sheets, LED luminaires, LED drivers, wiring and other defective components. Providing and fixing new UV stabilized translucent polycarbonate sheets of approved make and thickness (minimum 4-6 mm) on all illuminated faces, complete with necessary aluminium/SS sections, EPDM rubber gaskets, SS screws, silicone sealant etc. as required. Providing and fixing IP-65 LED linear lighting system inside the marker consisting of high efficiency LED modules/LED strips with aluminium profile, electronic constant voltage/current LED drivers, internal FRLS copper wiring, connectors, terminal blocks and all necessary accessories for uniform illumination of all faces. Surface preparation by removing existing damaged paint, rust, dust and loose material by sanding/grinding, applying one coat epoxy metal primer followed by two coats of exterior grade Polyurethane (PU) paint of approved shade and make on all exposed MS surfaces to achieve smooth and uniform finish. Re-assembling, transportation back to site, erection/reinstallation of the visual marker in its original position including alignment, anchoring, tightening of all fasteners, testing, commissioning and trial run complete as required. The item includes all labour, T&P, scaffolding/manlift, transportation, loading/unloading, consumables, fasteners, wiring, connectors and all incidental works complete. including rodent-proof G.I./Stainless Steel wire mesh at all cable entry points and other openings of the Architectural Light Column/Portal Frame to prevent entry of rodents, complete with necessary clamps, fasteners and sealant as required.The lumen output of the LED shall be equal to that of the existing Lumneries the LED module and driver shall be covered by a comprehensive 5 year warranty from the OEM. |
| 118 | Dismantling existing damaged pole i/c removing connection, removing the pole from site and transfer to JE(E) store. |
| 119 | Supplying &Laying of one number XLPE insulated and PVC sheathed aluminium conductor, armoured underground power cable of 1.1 KV grade of following size in the existing RCC/HUME/METAL/DWC pipe as required.4 x 16 sq. mm |
| 120 | 4 x 25 sq. mm |
| 121 | Supplying &Fixing of following size Aluminium thimble with proper connection and PVS Tape etc as required.16/25 Sqmm |
| 122 | Providing and laying in position M-20 (1:1.5:3) reinforced cement concrete foundation of size 400 mm.(L) X 400 mm wide and 1400 mm. with 750 x 750 x 100 mm PCC at base i/c excavation of earth, providing cutting, bending and placing in position, reinforcement of cold twisted bars of 12 mm dia- 1600 mm long (approx) - 8 Nos. and reinforcement ring of cold twisted bar of 8mm dia - 2000mm (approx) - 10 Nos. (with 140 mm spacing) as required with positioning of foundation bolts (as per item below) and providing 63 mm. (O.D) DWC, HDPE Pipe for cable entry & exit as required including J Hooks, nut Bolts, Washer, Anchor Plate, with welding of it as suitable for the pole. (For 6 Mtr Height Pole). |
| 123 | Supply, installation, testing and commissioning of MS tubular decorative step pole of 5.0 metre height, fabricated from suitable size mild steel tubular sections (Section A & Section B as required), complete with base plate of size 250 mm x 250 mm x 10 mm thick, duly welded at bottom for grouting on suitable foundation.The pole shall be metallic pre-treated through suitable chemical process to ensure corrosion resistance, followed by application of epoxy primer to make it alkaline resistant and to prevent rusting, and finished with UV stabilised PU paint of approved shade for long lasting protection against weathering and UV exposure.The pole shall be provided with IP rated junction box of suitable size, having 3-way connector, mounted on backside plate, complete with DIN rail arrangement for mounting of MCB, including all internal wiring, terminal connections, glands, lugs etc. as required.The complete item shall include supply and fixing of pole, grouting with foundation bolts, nuts, washers, anchor fasteners, making necessary connections, internal wiring, earthing provision, testing, commissioning and making the system fully operational, complete in all respects as per site requirement and directions of Engineer-in-charge. |
| 124 | Providing, boring and laying HDPE Pipes (ISI Marked) of 110mm O.D. confirming to IS:4984-1995 as amended upto date with pressure rating of 4Kg/Sq.m by trench less technology with no dig method by making bore hole in horizontal direction across the road as per direction of Engineer-In-Charge with Mouling equipment including cleaning, roadding of pipe , Providing suitable covers on mouth of pipe, excavation of pipe of required size at a depth of 1.30 Mtr. to 2.00 Mtr. |
| 125 | Fabricating, Supplying & Fixing wire mesh protection frame work made out of 40 mm x 6 mm thick angle & \\"T\\" strengthened with intermediate members of MS flat iron of size 30 mm x 5 mm thick welded at a distance of 30 cm horizontally & vertically and duly welded with wire mesh of size 75 mm x 25 mm made with 6 SWG wire mash of size 75 mm x 25 mm made with 6 SWG wire on all sides and top i/c providing and fixing of double door gate with double locking arrangement ( Two Nos. sliding bolts and One No go down lock) having 0.5 mtr. long legs of 40 mm x 40 mm x 6 mm thick angle iron, duly grouted in cement concrete foundation ration 1:2:4 (1 cement: 2 coarse sand : 4 graded stone aggregate), up to suitable depth painting with one coat of red oxide & Two coats of synthetic enamel paint of approval colour and shade and having provision of Central lock etc. complete as reqd. |
| 126 | Supplying of Power contactor 4 pole , 110 A, 415 volt having 2 NO+2NC contact (MNX-110/similar make). |
| 127 | Supplying of Astro Mini Timer in the existing cubical Panel with suitable connection etc as reqd. |
| 128 | Supplying and drawing following sizes of XLPE Insulated and PVC Round Sheathed Aluminium Conductor Heavy Duty Industrial Cables for Voltage Grade 1100 Volts as per IS: 694:1990. (Internal Wire)3 x 2.50 Sqm |
| 129 | Supplying and fixing of 40 Amp terminal block suitable for 25sq.mm conductor -4 nos. & shorting links – 5nos. on DIN channel i/c pdg. and fixing DIN channel of suitable length – 2 nos. on the existing laminated sheet.a) Supplying and fixing 6 Amp, SPMCB, ‘C’ Characteristics Curve - 2 No. Earth stud-2Nos. welded at suitable height two nos. washers, springs washers & nuts.b) Cable support clamp suitable for 4 Nos of 4x25 sqmm cable.c) The nuts and bolts shall be welded.. |
| 130 | Supplying and Laying of following sizes of XLPE insulated & PVC sheathed galvanised steel strip/wire armoured aluminium conductor cable of 1.1 KV grade of confirming to IS 7098 (part-I) amended upto date as required in the existing RCC/ HUME/ METAL pipe/DWC pipe i/c credit / buyback for old dismantled material i/c dismantling as on where it is basis etc complete as required . 4x25 sqmm |
| 131 | 4x16 sqmm |
| 132 | SITC of 50-75 W Decorative LED column light of height 3 mtr in two part LED module top made of pressure die cast aluminium housing and PC diffuser which contains LED, light distribution 360˚of colour temp 5700 k 230-240 V AC, CRI 770 built in LED modules with minimum delivered lumens output of 4500 lm, burning hours >50000 hrs at 40˚, driver efficiency >85% power factor≥0.90 THD ≤10%, surge protection 4 KV with IP 65, impact resistance IK≥07, optical grade clear polycarbonate diffuser and brand name should be embossed on it with MS PU painted bottom pipe Φ1.14 mm x 3.2 mm thickness, with connection window cover at an appropriate height of 600 mm from base plate for cable termination etc. and die cast aluminium top cover alongwith pretreated pipe Φ100 mm x 2.2 mm thickness and base plate size of 250x250x12 mm thick with 4 noselangated holes 20 mm dia to suit M16 x 450 mm long J- shape bolts at PCP 250 duly installed in CC foundation complete etc as required at site. |
| 133 | Supplying, installation, testing and commissioning of ring type 45 W LED Post Top made up of pressure die cast aluminium housing having 3/4 arms and PC diffuser with high power LED as lighting source suitable for 140-270 volt range of AC 50 Hz supply having ingress protection: >=IP 66, impact resistance: >=IK07, lumen efficacy: >=80 lumens/watt, Colour Temp: 5700K, CRI: >=70, THD: <=10%, driver efficiency: >=85%, Power factor minimum: >=0.95, Surge Protection: >=5KV, Average life: >= 50000 hrs, complete with all accessories and temper proof mounting arrangement on the existing Pole including connections etc as required. |
| 134 | Supplying, installation, testing and commissioning of 20 W LED Post Top made up of pressure die cast aluminium housing and PMMA diffuser with high power LED as lighting source & driver efficiency >=85% , IP65 protection and impact resistance of IK04 with 4 kV internal surge protection work on 220-240 volt AC Supply , CRI>=70 with lumen efficacy 100 lumens/watt or better, Power factor minimum >=0.95 , THD<=10%,5700K & average life >= 50000 hrs for better uniformity of lights complete with all accessories and mounting arrangement on the existing Pole including connections etc as required. |
| 135 | Supplying , Installation ,Testing andcommissioning of 3 Mtr height decorative pole having outer dia 80mm & with reducer on the top for installation of fitting, thickness of pole 3 mm with PU painted & size of Base plate 200 mm x 200 mm x 12 mm thickness , Foundation bolt M16 , 450 mm long with internal junction box having 1 No. 4 way connector and 1 no. 10A SPMCB including making arrangement for cable entry, making good the damages, pole wiring with suitable cable, connections etc. complete as reqd. |
| 136 | Providing and laying in position M-16 (1:2:4) reinforced cement concrete foundation of size 300 mm (L) x 300 mm (W) and 750 mm (D) i/c excavation of earth, providing cutting, bending and placing in position, reinforcement TMT bars of 10 mm dia -800 mm long (approx)-4 nos. and reinforcement ring of cold twisted bar of 8 mm dia - 1800 mm (approx) - 5 nos. (with 150 mm spacing) as required along with providing suitable 63 mm O.D. DWC HPDE pipe for cable entry and exit and positioning and fixing of 4 Nos. 20 mm diameter x 450mm long MS anchor bolts with nuts & washers including suitable sized anchor plates etc complete as reqd. |
| 137 | Supply & Fixing pole cover of different size etc. complete as per direction of Engineer-in- Charge. |
| 138 | Supply &Fixing of architectural head 4x20w as a part of CNC column light made of mild steel with overall height would be 600mm duly finished with desired PU paint finish. Black in Colour , coated for high corrosion resistance, silicone gasket, SS fasteners, integral driver, IP65, head comprising of 4 x 20W LED (110 lum/W) and low glare indirect line of visionEffiicacy> 85%, THD<10%, PF>0.9, surge protection > 4kV.CCT 3000K, CRI>70. etc. complete as per direction of Engineer-in- Charge. |
| 139 | Supply &Fixing of architectural column light accessories such as integral driver, IP65, IK≥07 for the complete light fixture including non-metallic portion; including bolts, fasteners and installation accessories. 360 deg light distribution in the column part provided with~ 6w/m linear vertical LED unit(90 lum/W). Efficacy > 85%, THD<10%, PF>0.9, surge protection > 4kV.CCT 3000K, CRI>70, SDCM<4 & IK≥07; as per direction of Engineer-in-Charge. |
| 140 | Supply and Replcement of 1 x 18/20 Watt LED Module with external LED Driver (4 KV surge protection) for repairing of decorative 4Mtr Post-Top Pole dome Light, Alum die cast housing, LED Mounted on MCPCB for better heat desperation, for existing decorative pole of twinkle make complete etc as reqd. |
| 141 | Dismantling of CC Paver Blocks/Cement Concrete / different types of Stone from the foot path in suitable width, excavation of trench 300 mm deep, refilling after cable work, reinstallation dismantled paver blocks / repairing the damages with CC 1:3:6 etc. complete as required. |
| 142 | Providing, boringand laying of 125 mm dia HDPE pipe by trench less technology with no dig method by making bore hole in horizontal direction across the road as per direction of Engineer-in-Charge, and ensureing compliance with electrical safety norms such as use of insulated tools, isolation of supply before work, use of PPE including gloves and safety shoes, and adherence to standard safety procedures. |
| 143 | Credit for old dismantle material.Assorted size aluminium Cable |
| 144 | Damaged panel without accessories |
| 145 | Assorted Decorative pole |
| 146 | Existing fittings |
| 147 | Existing poles Please Enable Macros to View BoQ information |
AI Tender Summary
Tender Timeline
Jul 16, 2026
11:30 IST
Tender Published
Tender notice published.
CompletedAug 06, 2026
17:00 IST
Bid Submission Deadline
Online submission via eProcurement portal.
Upcoming · 9 daysAug 06, 2026
Bid Opening Date
Technical bids will be opened and evaluated.
Upcoming · 9 daysTender Documents
Download All (ZIP) ↓
Disclaimer
We takes all possible care for accurate & authentic tender information. However users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender