Tender For Day To Day Maintenance Of T.E. Building & Staff Qtrs. In Ssa Mau (Fy 2026-27).
Tender Value
5.02 Lakhs
Estimated cost
Bid Submission
22 Jul 2026
5 days left
EMD
10055
Bank guarantee accepted
Document Fee
590
Non-refundable
Tender Type
Online
Tender Overview
Organization
Tender ID
Competition Type
NCB
Bidding Type
Tender
Location / State
Mau → Uttar Pradesh
EMD Exemption
Available
Quantity
Not Available
Website
Contact Person
Address
Project Description
Tender For Day To Day Maintenance Of T.E. Building & Staff Qtrs. In Ssa Mau (Fy 2026-27).
BOQ
| Sl. No. | Item Description |
| 1 | Clearing jungle including uprooting of rank vegetation, grass, brush wood, trees and saplings of girth up to 30 cm measured at a height of 1 m above ground level and removal of rubbish up to a distance of 50m outside the periphery of the area cleared. |
| 2 | Clearing grass and removal of the rubbish up to a distance of 50 m outside the periphery of the area cleared. |
| 3 | Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level : |
| 4 | 1:2:4 (1 cement : 2 coarse sand(zone-III) derived from natural sources : 4 graded stone aggregate 20 mm nominal size derived from natural sources) |
| 5 | Brick work with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in foundation and plinth in: |
| 6 | Cement mortar 1:6 (1 cement : 6 coarse sand) |
| 7 | Brick work with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in superstructure above plinth level up to floor V level in all shapes and sizes in : |
| 8 | Cement mortar 1:6 (1 cement : 6 coarse sand) |
| 9 | Providing and fixing ISI marked flush door shutters conforming to IS : 2202 (Part I) non-decorative type, core of block board construction with frame of 1st class hard wood and well matched commercial 3 ply veneering with vertical grains or cross bands and face veneers on both faces of shutters: |
| 10 | 30 mm thick including ISI marked Stainless Steel butt hinges with necessary screws. |
| 11 | Providing and fixing wire gauge shutters using galvanized M.S. wire gauge of average width of aperture 1.4 mm in both directions with wire of dia 0.63 mm, for doors, windows and clerestory windows with hinges and necessary screws : |
| 12 | 30 mm thick shutters |
| 13 | With ISI marked stainless steel butt hinges of required size - Second class teak wood |
| 14 | Providing and fixing nickel plated M.S. pipe curtain rods with nickel plated brackets : |
| 15 | 20 mm dia (heavy type) |
| 16 | Providing and fixing ISI marked oxidised M.S. sliding door bolts with nuts and screws etc. complete : |
| 17 | 250x16 mm |
| 18 | Providing and fixing ISI marked oxidised M.S. tower bolt black finish, (Barrel type) with necessary screws etc. complete : |
| 19 | 250x10 mm |
| 20 | 200x10 mm |
| 21 | Providing and fixing ISI marked oxidised M.S. handles conforming to IS:4992 with necessary screws etc. complete : |
| 22 | 125 mm |
| 23 | Providing and fixing oxidised M.S. casement stays (straight peg type) with necessary screws etc. complete. |
| 24 | 250 mm weighing not less than 150 gms. |
| 25 | Providing and fixing IS : 12817 marked stainless steel butt hinges with stainless steel screws etc. complete : |
| 26 | 100X58X1.90 mm |
| 27 | Providing and fixing aluminium die cast body tubular type universal hydraulic door closer (having brand logo with ISI, IS : 3564, embossed on the body, door weight upto 35 kg and door width upto 700 mm), with necessary accessories and screws etc. complete. |
| 28 | Providing and fixing aluminium sliding door bolts ISI marked anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour or shade with nuts and screws etc. complete : |
| 29 | 300x16 mm |
| 30 | 250x16 mm |
| 31 | Providing and fixing aluminium tower bolts ISI marked anodised (anodic coating not less than grade AC 10 as per IS : 1868 ) transparent or dyed to required colour or shade with necessary screws etc. complete : |
| 32 | 300x10 mm |
| 33 | 200x10 mm |
| 34 | Providing and fixing aluminium handles ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour or shade with necessary screws etc. complete : |
| 35 | 125 mm |
| 36 | Providing and fixing aluminium hanging floor door stopper, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour and shade, with necessary screws etc. complete. |
| 37 | Twin rubber stopper |
| 38 | Providing and fixing T-iron frames for doors, windows and ventilators of mild steel Tee-sections, joints mitred and welded, including fixing of necessary butt hinges and screws and applying a priming coat of approved steel primer. |
| 39 | Fixing with 15x3 mm lugs 10 cm long embedded in cement concrete block 15x10x10 cm of C.C. 1:3:6 (1 Cement : 3 coarse sand : 6 graded stone aggregate 20 mm nominal size). |
| 40 | Steel work welded in built up sections/ framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer using structural steel etc. as required. |
| 41 | In gratings, frames, guard bar, ladder, railings, brackets, gates and similar works. |
| 42 | Cement concrete flooring 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate) finished with a floating coat of neat cement, including cement slurry, but excluding the cost of nosing of steps etc. complete. |
| 43 | 40 mm thick with 20 mm nominal size stone aggregate |
| 44 | Pointing on brick work or brick flooring with cement mortar 1:3 (1 cement: 3 fine sand) : |
| 45 | Flush / Ruled/ Struck or weathered pointing. |
| 46 | Distempering with 1st quality acrylic distemper (ready mixed) having VOC (Volatile Organic Compound ) content less than 50 gram/ litre, of approved brand and of required shade and colour complete to give and even shade. |
| 47 | Old work (one or more coats) |
| 48 | White washing with lime to give an even shade : |
| 49 | Old work (two or more coats) . |
| 50 | Painting with synthetic enamel paint of approved brand and manufacture of required colour to give an even shade : |
| 51 | One or more coats on old work. |
| 52 | Repairs to plaster of thickness 12 mm to 20 mm in patches of area 2.5 sq. meters and under, including cutting the patch in proper shape, raking out joints and preparing and plastering the surface of the walls complete, including disposal of rubbish to the dumping ground , all complete as per directions of Engineer-In-Charge. |
| 53 | With cement mortar 1:4 (1 cement : 4 fine sand). |
| 54 | Renewing glass panes, with putty and nails wherever necessary including racking out the old putty: |
| 55 | Float glass panes of nominal thickness 4 mm (weight not less than 10kg/sqm). |
| 56 | Raking out joints in lime or cement mortar and preparing the surface for re-pointing or replastering including disposal of rubbish to the dumping ground, all complete as per directions of Engineer-In-Charge. |
| 57 | Cleaning of terrace/loft water storage tank (inside surface area) upto 2000 litre capacity at all heights with coconut brushes, duster etc., removal of silt, rubbish from the tank and cleaning the tank with fresh water disinfecting with bleaching powder @ 0.5gm per litre capacity of tank, including marking the date of cleaning on the side of tank body with the help of stencil and paint and disposing of malba, all complete as per direction of Engineer-in-Charge. (The old date already written on tank should be removed with paint remover or black paint and if date is not written with the stencil or old date is not removed deduction will be made @ Rs. 0.10 per litre if during cleaning any GI fittings or ball cock is damaged that is to be repaired by contractor at his own cost and nothing extra will be paid on this account) |
| 58 | Cleaning and de-silting of gully trap chamber, including removal of rubbish mixed with earth etc. and disposal of same, all as per the direction of Engineer-in-charge. |
| 59 | Providing and fixing Stainless Steel A ISI 304 (18/8) kitchen sink as per IS:13983 with C.I. brackets and stainless steel plug 40 mm, including painting of fittings and brackets, cutting and making good the walls wherever required : |
| 60 | Kitchen sink without drain board |
| 61 | 610x460 mm bowl depth 200 mm. |
| 62 | Providing and fixing white vitreous china water closet squatting pan (Indian type) : |
| 63 | Orissa pattern W.C. pan of size 580x440 mm |
| 64 | Providing and fixing P.V.C. low level flushing cistern with manually controlled device (handle lever) conforming to IS : 7231, with all fittings and fixtures complete. |
| 65 | 10 litre capacity - White |
| 66 | Providing and fixing solid plastic seat with lid for pedestal type W.C. pan complete : |
| 67 | White solid plastic seat with lid |
| 68 | Providing and fixing white vitreous china wash basin including making all connections but excluding the cost of fittings : |
| 69 | Flat back wash basin of size 550x400 mm. |
| 70 | Providing and fixing P.V.C. waste pipe for sink or wash basin including P.V.C. waste fittings complete. |
| 71 | Semi rigid pipe |
| 72 | 32 mm dia |
| 73 | Providing and fixing 100 mm sand cast Iron grating for gully trap. |
| 74 | Providing and fixing 600x450 mm beveled edge mirror of superior glass (of approved quality) complete with 6 mm thick hard board ground fixed to wooden cleats with C.P. brass screws and washers complete. |
| 75 | Providing and fixing mirror of superior glass (of approved quality) and of required shape and size with plastic moulded frame of approved make and shade with 6 mm thick hard board backing : |
| 76 | Rectangular shape 453x357 mm |
| 77 | Oval shape 450x350 mm (outer dimensions) |
| 78 | Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and testing of joints complete as per direction of Engineer in Charge. : Internal work - Exposed on wall |
| 79 | 15 mm nominal outer dia. Pipes. |
| 80 | 20 mm nominal outer dia. Pipes. |
| 81 | 25 mm nominal outer dia .Pipes. |
| 82 | 32 mm nominal outer dia. Pipes. |
| 83 | 40 mm nominal outer dia. Pipes. |
| 84 | Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, i/c fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and the cost of cutting chases and making good the same including testing of joints complete as per direction of Engineer in Charge. :Concealed work, including cutting chases and making good the walls etc. |
| 85 | 15 mm nominal outer dia .Pipes. |
| 86 | 20 mm nominal outer dia .Pipes. |
| 87 | 25 mm nominal outer dia .Pipes. |
| 88 | Providing and fixing G.I. pipes complete with G.I. fittings including trenching and refilling etc. : External work |
| 89 | 15 mm dia. nominal bore |
| 90 | 20 mm dia. nominal bore |
| 91 | 25 mm dia. nominal bore |
| 92 | 32 mm dia. nominal bore |
| 93 | 40 mm dia. nominal bore |
| 94 | Providing and fixing gun metal gate valve with C.I. wheel of approved quality (screwed end) : |
| 95 | 25 mm nominal bore |
| 96 | 32 mm nominal bore. |
| 97 | 40 mm nominal bore |
| 98 | 50 mm nominal bore |
| 99 | Providing and fixing C.P. brass shower rose with 15 or 20 mm inlet : |
| 100 | 100 mm diameter |
| 101 | Providing and fixing G.I. Union in existing G.I. pipe line, cutting and threading the pipe and making long screws including excavation, refilling the earth or cutting of wall and making good the same complete wherever required : |
| 102 | 15 mm nominal bore. |
| 103 | 20 mm nominal bore. |
| 104 | 25 mm nominal bore. |
| 105 | 40 mm nominal bore. |
| 106 | 50 mm nominal bore. |
| 107 | Providing and placing on terrace (at all floor levels) polyethylene water storage tank, IS : 12701 marked, with cover and suitable locking arrangement and making necessary holes for inlet, outlet and overflow pipes but without fittings and the base support for tank. |
| 108 | Providing and fixing C.P. brass bib cock of approved quality conforming to IS:8931: |
| 109 | 15 mm nominal bore. |
| 110 | Providing and fixing C.P. brass long body bib cock of approved quality conforming to IS standards and weighing not less than 690 gms. |
| 111 | 15 mm nominal bore |
| 112 | Providing and fixing C.P. brass stop cock (concealed) of standard design and of approved make conforming to IS:8931. |
| 113 | 15 mm nominal bore. |
| 114 | Providing and fixing C.P. brass angle valve for basin mixer and geyser points of approved quality conforming to IS:8931 : |
| 115 | 15mm nominal bore |
| 116 | Providing and fixing PTMT bib cock of approved quality and colour. |
| 117 | 15mm nominal bore, 86 mm long. Weighing not less than 88 gms. |
| 118 | Providing and fixing PTMT stop cock of approved quality and colour. |
| 119 | 15 mm nominal bore, 86 mm long. Weighing not less than 88 gms. |
| 120 | Providing and fixing PTMT pillar cock of approved quality and colour . |
| 121 | 15mm nominal bore, 107 mm long. Weighing not less than 110 gms. |
| 122 | Providing and fixing PTMT Ball cock of approved quality, colour and make complete with Epoxy coated aluminium rod with L.P./ H.P.H.D. plastic ball. |
| 123 | 20 mm nominal bore, 120 mm long. Weighing not less than 198 gms. |
| 124 | 25 mm nominal bore, 152 mm long. Weighing not less than 440 gms. |
| 125 | Providing and fixing PTMT angle stop cock 15 mm nominal bore. Weighing not less than 85 gms. |
| 126 | Providing and fixing PTMT swivelling shower, 15mm nominal bore. Weighing not less than 40 gms. |
| 127 | Providing and fixing unplasticised P.V.C. connection pipe with PTMT Nuts, collar and bush of approved quality and colour. |
| 128 | 15 mm nominal bore with 45 cm length. |
| 129 | Providing and fixing PTMT extension nipple for water tank pipe, fittings of approved quality and colour. |
| 130 | 15 mm nominal bore. Weighing not less than 32 gms. |
| 131 | 20mm nominal bore. Weighing not less than 40 gms. |
| 132 | 25mm nominal bore. Weighing not less than 62 gms. |
| 133 | Cutting holes up to 30x30 cm in walls including making good the same: |
| 134 | With common burnt clay F.P.S. (non modular) bricks. |
| 135 | Providing and fixing double action hydraulic floor spring of approved brand and manufacture conforming to IS : 6315, having brand logo embossed on the body / plate with double spring mechanism and door weight upto 125 kg., for doors, including cost of cutting floors ,embedding in floors as required and making good the same matching to the existing floor finishing and cover plates with brass pivot and single piece M.S. sheet outer box with slide plate etc. complete as per the direction of Engineer-in-charge. |
| 136 | With stainless steel cover plate minimum 1.25 mm thickness. |
| 137 | Repairing of leaking of toilet joint with P trap, floor traps, rain water pipes low level and high level cisterns. |
| 138 | Repairing of leaking in SCI pipes immediately i/c the cost of sealing material such as jute & cement etc. |
| 139 | P/F G.I. nipple to existing water line all complete as per direction of Engineer-in-charge. |
| 140 | a)15mm nominal bore. |
| 141 | i) 50mm size. |
| 142 | ii)100mm size. |
| 143 | iii)150mm size |
| 144 | b) 20mm nominal bore: |
| 145 | i) 50mm size |
| 146 | ii)100mm size. |
| 147 | iii)150mm size |
| 148 | c) 25mm nominal bore |
| 149 | i) 50mm size |
| 150 | ii) 100mm size |
| 151 | iii) 150mm size |
| 152 | P/F G.I. nipple for PVC tank all complete as per direction of Engineer-in-charge.. |
| 153 | a)15 mm nominal bore. |
| 154 | b)20mm nominal bore. |
| 155 | c)25mmnominal bore. |
| 156 | Repairing of wooden door/ window frames and shutters with part replacement of wood work wherever required after taking out the shutter i/c cost of wood replaced as per direction of Engineer-in-charge, repair at each location of shutter shall be treated as one job). |
| 157 | Providing manual assistance for plumbing sewer, masonry & carpentry work which are not covered in scheduled items and are not possible to measure. |
| 158 | P/F 26 gauge aluminium sheet i/c necessary nails etc. complete as per direction of Engineer-in-charge. |
| 159 | P/F C.P. brass waste Jali for sink or wash basin. |
| 160 | 32 mm dia |
| 161 | P/F PVC cover to over head PVC water storage tank i/c necessary nuts & bolts. |
| 162 | P/F stainless steel jail (grating) with or without hole for waste pipe for floor/Nahani trap. |
| 163 | 75 mm dia weight not less than 70 gms. |
| 164 | 100 mm dia weight not less than 100 gms. |
| 165 | Cleaning of Manhole with connecting sewer line and disposal of malva out side compound etc all complete as per direction of E-in-C. |
| 166 | Providing assistant for for day to day maintenance purpose. |
| 167 | Replacing damaged G.I. Jali in Jali doors/windows i/c cost of material & labour all complete as per direction of Engineer-in-charge. |
| 168 | Removal of chockage of floor/nahani trap, Ptrap, rain water pipe G.I. Supply lines & sanitary / drainage pipe lines etc. complete as per direction of E.-in-C. |
| 169 | Arranging electric welding machine at site for repairing works etc. with necessary cables and other T&P including the cost of operator and electrodes but excluding the cost of necessary steel sections complete as per direction of Engineer-in-charge. (Note: One day or part day work at one site shall be taken as one job.) |
| 170 | Cleaning septic tank up to capacity of 60 cum including removal of sludge, silt, garbage etc. all complete as per direction of Engineer-in-charge. |
| 171 | Eradication of plants grown on the walls of buildings i/c dismentling brick work/RCC wherever required and making good the same to match the existing surface etc all complete as per directios of the Engineer in Charge. |
| 172 | P/F G.I. Elbow in existing water line all complete as per direction of Engineer-in-charge. |
| 173 | a)15mm nominal bore. |
| 174 | b)20mm nominal bore. |
| 175 | c)25mm nominal bore. |
| 176 | P/F PVC Ball valve to PVC low level flushing cistern. |
| 177 | P/F PVC Syphon to PVC low level cistern all complete as per direction of Engineer-in-charge. |
| 178 | P/F gun metal gate valve with C.I. wheel of approved quality(screwed end): |
| 179 | a)20mm nominal bore. |
| 180 | P/F G.I. Tee of approved make in existing water line. |
| 181 | a)15mm nominal bore. |
| 182 | b) 20mm nominal bore. |
| 183 | c) 25 mm nominal bore |
| 184 | P/F MS bracket 40x40x5mm of size 40 cm. for fixing of wash basin and making good the same. |
| 185 | P/F G.I. Socket in existing water line all complete as per direction of Engineer-in-charge. |
| 186 | a)15mm nominal bore. |
| 187 | b)20mm nominal bore. |
| 188 | c)25mm nominal bore. |
| 189 | P/F SCI P trap to WC pan i/c labour charges & other fixing materials etc. all complete as per direction of Engineer-in-charge. |
| 190 | Disposal of malba out of compound upto municipal dump by mechanical means i/c loading and unloading complete as per directios of the Engineer in Charge. |
| 191 | Repairing of Aluminium door/ window frame and shutter with required cleat screws after taking out the shutter i/c cost of labour etc. all complete as per direction of E-in-C. |
| 192 | Extra for conveyance charges for attending complaints out side head quarter.( Payment shall be made on number of day attended for removal of complaints.) |
| 193 | Deduct for crediting to the contractor old unserviceable material obtained after dismantentling, |
| 194 | PVC stop cock, bib cock, pillar cock etc. |
| 195 | C.P. brass stop cock, bib cock. Pillar cock angle cock etc. |
| 196 | Brass stop cock, bib cock etc. |
| 197 | Gun metal/ brass gate valve 25mm&20mmetc. |
| 198 | PVC cistern10 litre |
| 199 | C.P. shower rose & spandle |
| 200 | Flush door shutter 35/30 mm thick |
| 201 | Hydraulic door closer |
| 202 | Aluminium twin rubber stopper |
| 203 | PVC water tank upto 500 ltr capacity |
| 204 | PVC water tank above 500ltr and upto 1000 ltr capacity Please Enable Macros to View BoQ information |
AI Tender Summary
Tender Timeline
Jul 15, 2026
11:30 IST
Tender Published
Tender notice published.
CompletedJul 22, 2026
17:00 IST
Bid Submission Deadline
Online submission via eProcurement portal.
Upcoming · 5 daysJul 24, 2026
Bid Opening Date
Technical bids will be opened and evaluated.
Upcoming · 7 daysTender Documents
Download All (ZIP) ↓
Disclaimer
We takes all possible care for accurate & authentic tender information. However users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender