Tender For Repair Of Path, Drain, Culvert, Compound Wall, Gate, Jafri Wall, Sewage Line, Repair/ Replacement Of Septic Tank Etc Of Unrestricted And Restricted Area Of Cqa (W) Of Dgqa Units Under Ge (P) No 1 Jabalpur
Tender Value
45 Lakhs
Estimated cost
Bid Submission
29 Jul 2026
13 days left
EMD
90000
Bank guarantee accepted
Document Fee
500
Non-refundable
Tender Type
Online
Tender Overview
Organization
Tender ID
Competition Type
NCB
Bidding Type
Tender
Location / State
Jabalpur → Madhya Pradesh
EMD Exemption
Not Available
Quantity
Not Available
Website
Contact Person
Address
Project Description
Tender for Repair Of Path, Drain, Culvert, Compound Wall, Gate, Jafri Wall, Sewage Line, Repair/ Replacement Of Septic Tank Etc Of Unrestricted And Restricted Area Of Cqa (W) Of Dgqa Units Under Ge (P) No 1 Jabalpur
BOQ
| Sl. No. | Item Description |
| 1 | Taking of liquid/solid content from sump/septic tank either manually or by pumping or by pumping clearing thoroughly including disposal of liquid/solid content out of the Cantt area, disposing in pit and covering with layers of earth and taking all pracautions against foul/hazardous gas etc (septic tanks, line, MH etc) complete all as specified and directed |
| 2 | M &L cleaning blockage by manually or mechanically in a sewage line up to 4.5 mtr depth, WC GT, NT, FT & man holes in AGE B/R area GE(P) No 1, Jabalpur by engaging safai wala for each Zone on all working days from 0830hr to 1700 hrs along with T & P incl gum boot, mask, safety device etc. are required for cleaning blockage and keep smooth functional the entire sewage lines including manholes to the entire stisfation of etc complete all as specified and directed .Note:- for sch A item above(i) Contractor or's supervisor will report on all w rking days along with 4 safai wala at 0830 hrs at B/R maintainance cell to receive complaint for blockage and to submit complintion report on same day by 1700 hrs.(ii) Printed complaint slip Area wise as per format approved by Engineer-in-Charge shall be provided and maintained by contractor. Cost for the same shall be deemed inclusive in the quited rate.(iii) Rate quoted above shall be deemed to incl the cost of adequate T&P, equipment, safety device etc alongwith sufficient labour to full fill the requirement to the entire satifaction of Engr-in-Charge. Any despute related to above shall be resolved by Garrison Engineer and his deceision shall be final, binding and conclusive.(iv) If there is any major blocks ge in sewer line for which additional Safaiwalas and special T&P is required same shall be provided by contractor without any extra cost to Govt there fore contractor is advice to visit the site before quoting the rate in tender.(v) All sewage blokage complaint must be attended within 24hr; if any sewage blockage complaint is not clear within 24 hrs (except and otherwise few major/ difficult complaint prior intimation/ notice to GE/ Engr in Charge) compensation of Rs. 100/- per Day per complaint shall be charged from contractor work done without any prior notice based on job card i.e. user satisfaction. (vi) Attendance register would be maintained by Engr in Charge in presence of contractor on each day for making the payment/recovery as per attendance. (vii) incl EPF/Insurance of labour etc.as per policy |
| 3 | S&F PVC (SWR) pipes 110 mm bore single socketed in any length with rubber ring joints laid in trenches or frenchs or in walls Complete all as specified and directed |
| 4 | S&F PVC (SWR) pipes 75 mm bore single socketed in any length with rubber ring joints laid in trenches or frenchs or in walls Complete all as specified and directed |
| 5 | Taking down of eaves gutter, rain water pipes of any size or pattern including all fittings etc. complete all as specified and directed. |
| 6 | S&F PVC (SWR) bends ISI marked any radius of 110 mm bore with access door complete all as specified and directed. |
| 7 | S&F PVC (SWR) bends ISI marked any radius of 75 mm complete all as specified and directed |
| 8 | S&F PVC (SWR) 110mm bore ,T, equal or unequal complete all as specified and directed |
| 9 | Demolition of un-reinforced Cement Concrete of any description and in any position not otherwise specifically provided for. Including Tile Bedding layers and removing out side MD Land complete all as specified and directed |
| 10 | M & L for cement concrete in foundations, filling and masss concrete type C2 1:3:6 (40mm graded aggregate) Complete all as specified and directed |
| 11 | Excavating in trenches in any type of soil , n exc 1.5 m wide and n. exc. 1.5 m in depth; for foundation, etc. or for shafts, wells, cesspits, manholes, pier holes, etc. n exc 10 sq m on plan and n exc 1.5 m in depth and getting out soil complete all as specified and directed. |
| 12 | Excavating in trenches in any type of soil , n exc 1.5 m wide and exc. 1.5 m in deep and n.exc 3.0m deep for foundation, etc. or for shafts, wells, cesspits, manholes, pier holes, etc. n exc 10 sq m on plan and getting out soil complete all as specified and as directed |
| 13 | Returning, filling in, including spreading ,leveling, watering and well ramming in layers n. exc 25 cm with soil complete all as specified and directed. |
| 14 | Removal of excavated material (soil) to a distance exc 50 m n. exc 250 m and depositing where directed at a level n.exc 1.5 m above the starting point complete all as specified and directed. |
| 15 | Supplying and laying and jointing for (SN 8) DWC Pipe 180mm (OD)/ 163 (ID) conforning to IS-16098:2013 part -I with and incl jointing materials complete all as specified and directed. |
| 16 | M&L for cement concrete bed to drain pipes including packing under and haunching against the sides of pipe after they are laid & tested for 150 mm bore of pipe with cement concrete 1:4:8 type D-2 using 40mm graded stone aggregate complete all as specified and directed. |
| 17 | M&L for extra for forming fair finished drain or channel 30 cm inner girth in cement concrete, using extra cement, including forms, moulds, mitred/stopped ends etc. Complete all as specified and directed. |
| 18 | M&L for Brick work with sub class B bricks straight or curved on plan exc. 6m mean radius built in cement mortar (1:4).complete all as specified and directed. |
| 19 | M&L for 15mm thick rendering on any faces of stone, concrete or brick work in CM 1:4 surface finished even and fair complete all as specified and directed. |
| 20 | M&L for 15 mm thick rendering in cement mortar (1:3) on brick / concrete/ stone surfaces mixed with water proofing compound as per manufacturer instruction , finished even and smooth using extra cement complete all as specified and directed. |
| 21 | Use and waste of formwork to soffits of suspended slabs such as roof slabs, floor slabs, landings and similar work; not exc 200mm thick (Horizontal or sloping) complete all as specified and directed. |
| 22 | M&L for cement concrete 1:2:4 type B1 (20 mm graded stone aggregate) as in coping Complete all as specified and directed |
| 23 | M&L for Precast (factory made frame and cover)cement concrete Type B-1 1:2:4 (Using 20 mm graded stone aggregate) in landings, cover slabs (for manholes etc.) shelves and similar articles with plain faces and set in cement mortar 1:6 complete all as specified and directed. |
| 24 | S&F TMT steel bars 6 to 8mm in reinforcement, cut to length, bent to shape required including cranking, bending spirally or hooping for columns, hooking ends and binding with MS wire (annealed not less than 0.9mm dia) all as specified and directed. |
| 25 | M&L for Broken bricks of gauge not exceeding 63 mm for loose filling in sokage pit, sokage wells complete all as specified and directed. |
| 26 | M&L for cement concrete type B2 , 1:2:4 using 40 mm gradded stone aggregate in surface channels and drains Complete all as specified and directed |
| 27 | Taking down cement or cement lime plaster, any description on brick or stone walls, etc. including raking out joints, hacking for key, scrubbing down with water, etc Complete all as specified and directed. |
| 28 | Demolition of floor, hearth or wall tiling including cement mortar bedding etc (but not backing) and removing rubbish off the premises complete all as specified and directed. |
| 29 | M & L for cement concrete as in foundations, filling and masss concrete type D2 1:4:8 (40mm graded aggregate) Complete all as specified and directed |
| 30 | M&L for vetrified paver ceremic tiles 10 mm thick, in light shade, (Square/rectangular) polished, area of each tile not exceeding 0.36 sqm, in floors etc. set & jointed in neat cement slurry and pointed in coloured cement to match coloured tiles laid over and including 15 mm thick screed bed or bedding layer in CM (1:6) complete all as specfied and directed. |
| 31 | Excavating in post holes (or similar holes) each n exc 0.5 cu. m, getting out, returning, filling in and ramming earth or broken rubble mixed with earth around, in layers not exceeding 25 cm in hard dense soil Complete all as specified and directed |
| 32 | Fixing only in repair chain link fencing including line wires, any mesh, size and type to any type of standards, rails, straining bolts, etc. including provision of binding wire complete all as specified and directed. |
| 33 | Supply only chain link fencing, , any width and dia of wire not less than 3.00 mm complete all as specified and directed. |
| 34 | M&L for mild steel round bars 10mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for securing chain link fencing complete all as specified and directed. |
| 35 | S&F framed work as in doors or gates of angle or other section with gussest plates, rails, braces, etc, complete drilled for fixing and incl steel sheeting or other covering doors etc, to be prepared for hanging and sliding with and including either hooks and hinges or steel hnging door fittings and fixing conferming to gde Fe 410-w Complete all as specified and directed. |
| 36 | Dismantling wrought iron or mild steel work of any description not otherwise provided for Complete all as specified and directed. |
| 37 | M&L Hand rails, half round or other steel section or core for wooden hand-rail straight portion, drilled and countersunk for balusters running bars, for doors, balusters, nosing to steps including embeding in concrete and screwing etc. wind ties for roof including securing bolts; posts and struts in fencing including cutting tops to shape as directed, drilling holes, notching for wire, etc.; flat iron fillets (for securing wire mesh etc.) including all necessary drilling, bolting or riveting, etc., and similar work conforming to Fe-290 Gde E-165 etc Complete all as specified and directed. |
| 38 | Supply and fixing in repair Concertina Coil Mild steel punched tape concertina coil with Zinc coating 450mm Ø with clips spaced 24mm dispensed in compact rolls weighing 7.5 kg/coil covering an average span of 7.5m on expansion to be laid between the 'Y' angle pickets joining by welded at 45 degree slope lap complete all as specified and directed. |
| 39 | Dismantling posts or struts concrete work or brick masonry (wood, steel or R.C.C.) any section, including taking out embedded portion and making good disturbed ground complete all as specified and directed. |
| 40 | Dismentling of fencing wire mesh any type complete all as specified and directed. |
| 41 | S&F for Galvanised. 2 strand, steel barbed wire 2.24mm dia barbed with 2mm dia barbs at 75mm spacings and straining and fixing to any type of standard rails strain- ing bolts, including, securing or tying at crossings with and provision of galvanised mild steel wire, staples or steel pins, etc. as directed (each line wire to be measured) complete all as specified and directed. |
| 42 | M&L Preparation of two coats of synthetic enamel paint on new steel surfaces of any description, over 10cm in width or girth,not otherwise described including preparation over a coat of red oxide Zinc chrome prime complete all as specified and directedr complete all as specified and directed. |
| 43 | S&F in repair Black colour solid ACP wall lining consisting of 3mm thick plain inclusive of solvent cement /Adhesive including Alluminium frame work Complete all as specified and directed. |
| 44 | S&F in repair for SS Box type Letters Height 12\\" to 18\\" including Led Lighting and connection up to Main Socket/DB Nos of Letters up to 40 white fixed to ACP sheet as in repair Complete all as specified and directed |
| 45 | S&F in repair MES LOGO 0.5 to 1.0 m height with LED module & power supply cable DB etc as in repair Complete all as specified and directed. |
| 46 | M&L for non skid ceramic tiles, joint free, coloured tiles 7mm to 8 mm thick (Square or rectangular) area of each tile exceeding 0.11 sqm but not exceeding 0.42 sqm, in floors etc set over and including 15 mm thick cement screed in (1:4) CM set and jointed in neat cement slurry and pointed in white or coloured cement to match with the colour of tiles Complete all as specified and directed |
| 47 | M&L for ceramic tiles, joint free, coloured tiles 7mm to 8 mm mm thick as in skirting fixed over and including 10 mm thick cement screed in (1:3) CM set and jointed in neat cement slurry and pointed in white or coloured cement to match with the colour of tiles complete all as specified and directed.with the colour of tiles complete all as specified and directed. |
| 48 | M&L for digital glazed ceramic tiles, coloured tiles 300mm x 450mm x 7mm thick on vertical faces ie. as in skirting/dado etc set & jointed in neat cement slurry and pointed in white or coloured cement to match the colour of tiles fix over and including 10 mm thick backing coat in cement mortar (1:3) complete all as specified and directed. |
| 49 | M&L for PCC (1:2:4) type B2, (using 20 mm graded stone aggregate), as in foundations / mass concrete/ levelling course complete all as specified. |
| 50 | M&L for machine cut cuddapa stone slab 30-35 mm thick , as in platform below WHB etc complete all as specified and directed. |
| 51 | Demolition of brick work /stone work built in cement mortar including all quoins, arches, pillars etc complete all as specified and as directed. |
| 52 | M&L for Brick work with sub-class `B' bricks, straight or curved on plan to any radius, in half brick work built in cement mortar 1:4 complete all as specified and directed. |
| 53 | M&L for 75mm thick PCC (1:2:4) Type C2 using 40mm graded stone agg as in plinth protection surface even and fair without using extra cement including forming & filling expension joints 65 mm deep x 10 mm wide filled with sealing compound grade A complete all as specified and diected |
| 54 | M&L for 15 mm thick rendering in cement mortar (1:6) on brick or concrete surfaces finished even and fair without using extra cement complete all as specified and directed. |
| 55 | M&L for rendering 5 mm thick in Cement Mortar (1:3) on ceiling finished even and fair without using extra cement complete all as specified and directed. |
| 56 | M&L for preparation of the newly plastered surfaces of walls & applying three coats of white wash on wall surfaces complete all as specified and directed. |
| 57 | M&L for preparation of the newly plastered surfaces of ceiling & applying 3 coats of white wash on ceiling surfaces complete all as specified and directed. |
| 58 | M&L Preparation of old decorated surface of ceiling and including cornices plastered or unplastered surfaces by brooming down or steel wire brushing to remove all loose scales, and foreign materials scarping down , smoke soot moulds , moss and efflorescent salts treating oil and greasy spots and applying one coat of white wash complete all as specified and directed. |
| 59 | M&L Preparation of old decorated surface of wall and including cornices plastered or unplastered surfaces by brooming down or steel wire brushing to remove all loose scales, and foreign materials scarping down , smoke soot moulds , moss and efflorescent salts treating oil and greasy spots and M&L for one coats of distemper oil emlusion white or tinted complete all as specified and dircted |
| 60 | M&L for Preparing of old decorated surface of wall and including cornices plastered or unplastered surfaces by brooming down or steel wire brushing to remove all loose scales, and foreign materials scarping down , smoke soot moulds , moss and efflorescent salts treating oil and greasy spots and M&L applying one coat of white wash , complete all as specified and directed. |
| 61 | M&L preparation of old painted wooden surfaces and providing one or more coat of synthetic enamal incl preparation of Surfaces of any description, not otherwise descri-bed, over 10cm width or girth Complete all as specified and directed |
| 62 | S&F in repair Providing precast cement concrete louvres and jallies, 35mm thick, including all mould- ings of type B0 1:4 using 12.5mm graded stone aggreate set in cement mortar 1:6 (Reinforecement shall be measured and paid separately) Complete all as specified and directed. |
| 63 | All as per item No. 62 above but except Jally in cement mortar 1:6 Complete all as specified and directed |
| 64 | M&L for RCC (Design mix M-25) in foundations, including, rafts, footings, foundation beams, bases for columns, etc , basement slab, under reamed piles and mass concrete Complete all as specified and directed |
| 65 | M&L for RCC M-25 design mix as in columns , pillars, piers, posts and struts etc. Complete all as specified and directed |
| 66 | M&L for RCC M-20 design mix as in being cantiliver, chajjas, lintels and using 20mm graded stone aggregate complete all as specifed and directed |
| 67 | Use and waste of formwork to sides of concrete foundations, footings, bases of columns, raft and raft beams, sides and soffits (if any) of foundation and plinth beams; and similar work, vertical or to batter Complete all as specified and directed |
| 68 | Use and waste of formwork to sides of pillars, posts, struts, piers, columns etc square or rectangular Complete all as specified and directed |
| 69 | Use and waste of formwork to sides and soffits of floor or roof beams, beam haunchings, girders, bressummers, lintels, cantilevers, shelves, chajjas including sup- ports, overhangs, etc. also splays between floors and beams, etc. for rough finish surfaces flate or curved complete all as specified and directed |
| 70 | S&F mild steel TMT steel bars 10 mm dia and over in reinforcement, cut to length, bent to shape required including cranking, bending spirally or hooping for columns, hooking ends and binding with MS wire (annealed not less than 0.9mm dia) Complete all as specified and directed. |
| 71 | S&F mild steel TMT steel bars 5 mm dia and over, up to and including 10mm dia in stirrups spcers and binders. Complete all as specified and directed |
| 72 | M&L for Brick work with Fly ash bricks straight or curved on plan exc 6m mean radius built in CM (1:6) using old size bricks Complete all as specified and directed |
| 73 | M&L for rendering 15mm thick in cement mortar 1:4 on fair faces of brick work or concrete surfaces finished even and smooth with out using extra cement. Complete all as specified and directed |
| 74 | Material & Labour for Distempering with 1st quality acrylic distemper (ready mixed) having VOC content less than 50 gms/litre, of approved manufacturer, of required shade and colour complete, as per manufacturer's specification. Two or more coats on new/old work including preparation of existing wall surfaces including primer/removing of existing treatment etc Complete all as specified and directed. |
| 75 | Material & Labour for applying Two or more coats of 100% Premium acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives @ 1.43 litre/ 10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/ 10 sqm over new/old surfaces including preparation of existing wall surfaces (and removing existing treatment) complete all as specified and directed. |
| 76 | M&L for 16-18mm thick granite stone slab of any type with table rubbed and polished in cooking platforms,window sill and like set in cement mortar 1:4 including pointing in white cement (1:2) using marble dust with admixture of pigment to match the shade of granite slab complete all as specified and directed. |
| 77 | Material & Labour for providing and fixing stainless steel (Grade 304) railing /moulded/ orinimantal door made of hollow tubes,channels, plates etc., including welding, grinding,buffing, polishing and making curvature (where ever required) and fitting the same with necessary stainless steel nuts and bolts complete, including fixing the railing with necessary accessories & stainless steel dash fasteners, stainless steel bolts etc., of required size, on the top of floor or the side of waist slab with suitable arrangement complete all as specified and directed. |
| 78 | M&L for Providing and laying 60mm thick factory made chamfered edge cement concrete paver block of M-30 grade with approved colour, design & pattern as in footpath, parks, lawns, drive ways or light traffic parking etc., of required strength, thickness & size/ shape, made by table vibratory method using PU mould, laid in required colour & pattern over and including 50mm thick compacted bed of coarse sand,compacting and proper embedding/ laying of inter locking paver blocks into the sand bedding layer through vibratory compaction by using plate vibrator, filling the joints with fine sand and cutting of paver block as per required size and pattern, finishing and sweeping extra sand;complete. complete all as specified and directed. |
| 79 | S&F Providing and laying at or near ground level factory made kerb stone of M-25 grade cement concrete in position to the required line, level and curvature, jointed with cement mortar 1:3 (1 cement: 3 coarse sand), including making joints with or without grooves (thickness of joints except at sharp curve shall not to more than 5 mm), including making drainage opening wherever required complete all as specified and directed. |
| 80 | M&L for moorum/red bajri filling in floors or paving laid in layers n. exc 15 cm thick spreading levelled and blinded with earth and rammed including watering complete all as specified and directed. |
| 81 | S&F in repair Pillar taps 15mm fancy type cast copper alloy, with capstan heads,chromium plated,screwed down high pressure, with or without lettered 'Hot' or 'Cold' with long screwed shanks and fly-nuts,screwed for iron pipe and fixed complete all as specified and directed. |
| 82 | S&F in repairs white vitreous china wash down water closet pan pedestal pattern (white) excluding fixing bolts, flushing cistern and flush pipe complete all as specified and directed. |
| 83 | S&F in repair white vitreous china orissa pettern of size 580mmx440 mm white with integral footrest excluding flushing cistern complete all as specified and directed. |
| 84 | S&F in repair plastic water closet seat, white/ black closed pattern with flat bottom and cover and mild steel chromium plated or aluminized hinging device complete all as specified and directed. |
| 85 | S&F in repair vitreous china urinal half stall type white excluding flushing cistern flush pipe and waste pipe complete all as specified and directed |
| 86 | S&F Vitreous china WHB 550x400mm including cutting pinning in end of brackets brackets , fixing flat back or angle back/oval type type with PVC (hdpe) 32 mm dia waste pipe, brass coupling 32 mm CP etc fixed in repair complete all as specified and directed. |
| 87 | S&F fancy type stainless steel draphery rods with brackets 20-25mm bore including stop roller lid and knobs etc cut to length as required of colour complete all as specified and directed. |
| 88 | S&F in repair wall mixer 2 in 1 suitable for 15mm board as in repair Brass CP mixer for mixing hot & cold water screwed down for iron pipe and fixed complete all as specified and directed. |
| 89 | S&F as in repair wash basin/sink mixer Brass CO mixer for mixing hot & cold water screwed down for iron pipe F114 and fixed. complete all as specified and directed. |
| 90 | S & F in repair for Bib taps, cast copper alloy with crutch or butterfly handle, sc-rewed down, screwed for iron pipe or for brass ferrule and fixed, 15 mm, fancy type, chromium plated fixed complete all as specified and directed. |
| 91 | S&F for Sheet corner glass shelf assembly consisting of 5.5mm thick sheet glass shelf 12 cm wide with chromium plated bracket guard and railing 60 cm long complete all as specified and directed. |
| 92 | S&F in repair Chromium plated toilet paper holder including fixing arrangement complete all as specified and directed. |
| 93 | S & F in repair for Soap dish, any type, fixed to plugs with chromium plated brass screws fixed complete all as specified and directed. |
| 94 | S&F in repair for fency type chromium plated Stop valves,(angle Cock) cast copper alloy, screwed down, high pre-ssure, with crutch or but-terfly handle, screwed both ends for iron pipe or for unions and fixed ,15 mm fixed complete all as specified and directed. |
| 95 | S & F in repair for Gun-metal, globe or gate valves, with lever head/iron wheel head, screwed both ends for iron pipe and fixed , 20 mm fixed complete all as specified and directed. |
| 96 | S & F for PVC connections 15 mm size with PTMT nuts of length 600mm fixed complete all as specified and directed. |
| 97 | S&F PVC low level flushing cistern of capacity 10 litres complete with siphon handle lever float valve and PVC bend including connecting to ITWC/ ETWC and fixing on wall bracket complete all as specified and directed. |
| 98 | Taking down steel tubing and connections including cleaning for refixing or removal form site for 25mm bore pipe complete all as specified and directed. |
| 99 | Taking down steel tubing and connections including cleaning for refixing or removal form site for upto 20mm bore pipe complete all as specified and directed |
| 100 | Supply & laying of CPVC pipes 25 mm Outer dia, SDR 11 & Plain CPVC SDR 11 fitting on wall/ceiling or laying in floors complete all as specified and directed. |
| 101 | Supply & laying of CPVC pipes 20 mm Outer dia, SDR 11 & Plain CPVC SDR 11 fitting on wall/ceiling or laying in floors complete all as specified and directed. |
| 102 | PVC (SWR) floor trap / Nahani trap with grating 75 mm dia incl jointing with solvent cement complete all as specified and directed. |
| 103 | Taking down chowket or frame with shutter (without taking of shutters from the frames) area not exceeding 1.5 Sq mtr each complete all as specified and directed |
| 104 | Taking down chowket or frame with shutter (without taking of shutters from the frames) area exceeding 1.5 Sq mtr each not exceeding 4.00 Sq mtr each complete all as specified and directed. |
| 105 | S&F solid PVC door frame of size 50mm x 47mm made out of 5mm plain clour PVC sheet reinforced with M.S square tube in opening as per specification including making good to the disturbed surfaces and matching existing treatment (cemnt base paint/distemper/white wash/plastic paint) etc complete all as specified and directed. |
| 106 | S&F Factory made solid panel PVC door shutter 30 mm thick (style) consisting of frame made out of M.S. tubes for top & bottom rails. M.S. frame shall be covered with heat moulded plain colour PVC ‘C’ channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail; Panelling of plain colour PVC sheet to be fitted in the M.S. frame welded / sealed to the stiles & rails with suitable PVC sheet beading, and joined together with solvent cement, suppling & fixing in the frame at site as per specification & drawing. complete all as specified and directed. |
| 107 | S&F 150 mm long aluminium anodised barrel tower bolt and 12 mm dia fixed complete all as specified and directed. |
| 108 | S&F 150mm long aluminium anodised handle cast type and fixed complete all as specified and directed. |
| 109 | S&F alluminum alloy, anodised, sliding door bolt with hasp & staple (bolt type) and length of 300 mm long etc.complete all as specified and directed. |
| 110 | S&F 100mm long butt hinges med wt cold rolled mild steel and fixed complete all as specified and directed. |
| 111 | S&F butt hinges of extruded Alluminium alloy with galvanied MS hinge pin anodised and fix type C-22 of 100 mm size complete all as specified and directed |
| 112 | S&F in repair APP based polymeric membrane minimum weighing 3kg/sqm and minimum 3mm thick reinforced with polyster non wove fabric (wt. not less than 150 gms/sqm)incl bitumen base primer 0.3Kg per SQM laid over primed surface by forced torch application complete all as specified and directed. |
| 113 | Supply and fixing Heat Resistant Terrace Tiles (300 mm x 300 mm x 20 mm) with SRI (solar refractive index) > 78, solar reflection > 0.70 and initial emittance > 0.75 on waterproof and sloped surface of terrace, laidon 20 mm thick cement sand mortar in the ratio of 1:4 (1 cement : 4 coarse sand) and grouting the joints with mix of white cement & marble powder in ratio of 1:1, including rubbing and polishing of the surface upto 3 cuts complete, including providing skirting upto 150 mm height along the parapet walls in the same manner.complete all as specified and directed. |
| 114 | M&L for one or more coat of heat resistance aluminium paint over bitumen surfaces of any description wood, steel, iron, concrete, brick, stone, etc., exceeding 10cm in width or girth complete all as specified and directed. |
| 115 | Dismentaling of timber scantling as in fillets, rails posts rafters purlin etc under 40 Sqcm in section as in unframed work complete all as specified and directed |
| 116 | S&F in repair rotational moulded polyethylene water storage tanks (cylindrical vertical with closed top) capacity 500 Ltr hoisted and fixed in position including dismentling of old tank and fixing of 20 mm float valve complete all as specified and directed. |
| 117 | S&F in repair /fixed to door window,vent for stainless steel wire cloth 0.36 mm nominal dia of wire and average width of aperture 1.40mm and fixed with tinned tacks or galvanized wire staples beads or in steel window complete all as specified and directed. |
| 118 | S & F Factory made single extruded WPC (Wood Polymer Composite) solid door/ window/Ceosetory windows & other Frames/ Chowkhat of size 60 x 100 mm comprising of virgin PVC polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/ wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) fabricated with miter joints after applying PVC solvent cement and screwed with full body threaded star headed SS screws having minimum frame density of 750 kg/ cum, screw withdrawal strength of 2200 N (Face) & 1100 N (Edge), minimum compressive strength of 58 N/mm2, modules of elasticity 900 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof,water/ moisture proof and fire retardant 152 SECTION 8 and fixed in position with MS hold fast/ lugs/SS dash fasteners of required dia and length complete all as specified and directed. |
| 119 | S & F Factory made single extruded WPC (Wood Polymer Composite) solid door/ window/Ceosetory windows & other Frames/ Chowkhat of size 60 x 125 mm comprising of virgin PVC polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/ wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) fabricated with miter joints after applying PVC solvent cement and screwed with full body threaded star headed SS screws having minimum frame density of 750 kg/ cum, screw withdrawal strength of 2200 N (Face) & 1100 N (Edge), minimum compressive strength of 58 N/mm2, modules of elasticity 900 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof,water/ moisture proof and fire retardant 152 SECTION 8 and fixed in position with MS hold fast/ lugs/SS dash fasteners of required dia and length complete all as specified and directed. |
| 120 | S&F for Factory made solid panel PVC door shutter 30 mm thick (style)wire gauge i.e panel will be wire gauge in lieu of single side prelam PVC sheet panel . The wire gauge shell be wrapped on an additional square 8 mm MS solid tube the wire gauge strightly and tighted firmly, suppling & fixing in the frame at site as per specification & drawing (Includind SS wire mesh of 0.35 mm dia and 1.18 mm aperture) complete all as specified and directed. |
| 121 | S&F for Factory made single extruded WPC (Wood Polymer Composite) solid plain flush door shutter of 30mm size comprising of virgin polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) having minimum density of 650 kg/cum and screw withdrawal strength of 1800 N (Face) & 900 N (Edge), minimum compressive strength 50 N/mm2, modulus of elasticity 850 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/moisture proof and fire retardant and fixing with stainless steel butt hinges of required size with necessary full body threaded star headed counter sunkS.S screws, complete all as specified and directed. |
| 122 | Dismentling of wall and ceiling board (fibre pulp insulation etc or insulation board /slab/blanket any thickness including cover fillets complete all as specified and directed. |
| 123 | M & L for 18mm thk lnsulated PVC Wall Lining consisting of PVC Insulated Panels with single side Prelam PVC sheet used in-stead of Plain colour sheet as in cupboard, wardrob and similar works etc work to be done at site complete all as specified and directed. |
| 124 | S&F in repair continuous (Piano) hinge 30-32 mm of MS CP or electro galvanized complete all as specified and directed. |
| 125 | Dimantling of PVC fibre roof sheeting, corrugated or semi corrugated or similar pattern roof coverings complete all as specified and directed. |
| 126 | Dimantling asbestos cement sheeting, corrugated or semi corrugated or similar pattern roof coverings complete all as specified and directed. |
| 127 | M&L for Pre-painted galvatume aluminium zinc coating GI based corrugatged steel sheet 0.5mm thick of an colour having tensile strength of 550 Mpa as in roof covering /cladding to wall, fixed with self tapping screws complete all as specified and directed. |
| 128 | M&L for Pre-painted galvalume aluminum zinc coating GI based Plain steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws as specifiedt complete all as specified and directed. |
| 129 | Dismantling timber scantlings 40 sq. cm and over in section, in any position unframed works complete all as specified and directed. |
| 130 | S&F for Rolled sections as in main and cross beams, hip and jack rafters; purlins where connected to common rafters and running rails and guides for sliding doors; fixed with angle cleats or other connecting plates complete all as specified and directed. |
| 131 | S&F for 5.5 mm thick ordinary glass and glazing with oil putty in square area exc 0.50 sqm in each pane complete all as specified and directed. |
| 132 | S&F for 12 mm thick Prelaminated particle board, exterior grade,prelaminated both side with decorative choice lamination colour both side side balancing white lamination, fixed with screws to timber frame work complete all as specified and directed. |
| 133 | S&F for Powder coated aluminium (minimum thickness of powder coating 50 micron) work for doors,windows, ventilators and partitions (Fixed portions) with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS:733 and IS:1285, fixing with dash fasteners of required dia and size,including necessary filling up the gaps at junctions, i.e. at top,bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle,Aluminium snap beading for glazing/ paneling, C.P. brass/ stainless steel screws, complete all as specified and directed. |
| 134 | Schedule of credit of Amount Rs. 46,832.00 to be deducted during AOC. Please Enable Macros to View BoQ information |
AI Tender Summary
Tender Timeline
Jul 15, 2026
11:30 IST
Tender Published
Tender notice published.
CompletedJul 29, 2026
17:00 IST
Bid Submission Deadline
Online submission via eProcurement portal.
Upcoming · 13 daysAug 06, 2026
Bid Opening Date
Technical bids will be opened and evaluated.
Upcoming · 21 daysTender Documents
Download All (ZIP) ↓
Disclaimer
We takes all possible care for accurate & authentic tender information. However users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender