Tender For - Provision Of Duty Armour Rest Room At Af Stn Bhowali.
Tender Value
9.70 Lakhs
Estimated cost
Bid Submission
05 Aug 2026
7 days left
EMD
19400
Bank guarantee accepted
Document Fee
500
Non-refundable
Tender Type
Online
Tender Overview
Organization
Tender ID
Competition Type
NCB
Bidding Type
Tender
Location / State
Nainital → Uttarakhand
EMD Exemption
Available
Quantity
Not Available
Website
Contact Person
Address
Project Description
Tender for - Provision Of Duty Armour Rest Room At Af Stn Bhowali.
BOQ
| Sl. No. | Item Description |
| 1 | Excavating in trenches, n exc 1.5m wide and n exc 1.5m in depth; for foundation, n exc 10 sqm on plan and n exc 1.5m in depth and getting out any type of soil complete all as specified and as directed. |
| 2 | Surface excavation n. exc 30cm deep and averaging 15cm deep and getting out in hard soil/dense soil/existing surface complete all as specified and directed. |
| 3 | Removing excavated materials n. exc. 50 m and depositing were directed at a level n exc 1.5 mtr above the staring point complete as specified and as directed. |
| 4 | Returning, filing in, excavated soil including spreading, levelling, watering and well ramming in layers not exceeding 25cm etc complete all as specified and directed |
| 5 | M&L for Moorum/red bajri filling in floors or pavings, laid in layers n exc. 15 cm thick, spread, levelled and rammed including watering complete all as specified and directed. |
| 6 | M&L for hard core of gauge n.exc 63mm , degorited spread and levelled in layers n.exc 15mm thick watered and rammed to a tree surface with broken stone or boulders complete all as specified & as directed.. |
| 7 | M&L 25mm thick PCC 1:2:4 type B0 (12.50mm graded crushed stone aggregate) as in floors finished even & smooth using extra cement in patches, complete all as specified and directed. |
| 8 | M&L vetrified ceremic tiles 10 mm thick, in light shade, (Square/rectangular) polished, area of each tile not exceeding 0.36 sqm, in floors etc. set & jointed in neat cement slurry and pointed in coloured cement to match coloured tiles laid over and including 15 mm thick screed bed or bedding layer in CM (1:4) complete all as specfied and directed. |
| 9 | All as per above item no-08 but in skirting with rendering 10mm thick CM 1:4 complete all as specified and as directed. |
| 10 | M& L for Cement concrete type E-2 1:4:8 (using 40 mm graded aggregate) as in foundation filling and mass concrete complete all as specified and directed. |
| 11 | M& L for RCC in Nominal Mix type B1 1:2:4 (20mm graded aggregate) foundations, including, rafts, footings, foundation beams (Plinth beam), bases for columns, etc , basement slab, under reamed piles and mass concrete complete all as specified and directed |
| 12 | M&L for Reinforced cement Concrete (Nominal mix) type B1 1:2:4 (using 20mm graded stone aggregate) as in columns , pillars, piers, posts and struts etc. complete all as specified and directed. |
| 13 | M&L for reinforced cement concrete (nominal mix) type B1 1:2:4 20mm graded stone aggregate as in beams, (Lintel and roof) cantilevers, bressummers, lintels over 1.5m span complete all as specified and directed. |
| 14 | M&L for RCC in Nominal Mix type B1 1:2:4 (20mm graded aggregate) in Slabs supported on walls, beams and columns in floors, roofs, landings, balconies, canopies, deck slabs and in shelves and the like complete all as specified and directed |
| 15 | M&L for formwork to sides of concrete foundations, footings, bases of columns, raft and raft beams, sides and soffits (if any) of foundation and plinth beams; and similar work, vertical or to batter complete all as specified and directed |
| 16 | M&L for formwork to sides of pillars, posts, struts, piers, columns etc square or rectanguar complete all as specified and directed |
| 17 | M&L for formwork to sides and soffits of floor beams, roof beams , beam haunchings girders, lintels, cantilevers etc to plain surface complete all as specified and directed. |
| 18 | M&L for Formwork to soffits of suspended slabs such as roof slabs, floor slabs, landings & similar work; not exc. 200m thick (Horizontal or sloping) Fair finished surfaces of concrete flat complete all as specified and directed. |
| 19 | Supply and fixing TMT steel bars 10mm dia and over in reinforcement, cut to length, bent to shape required including cranking, bending spirally or hooping for columns, hooking ends and binding with MS wire (annealed not less than 0.9mm dia) complete all as specified and directed. |
| 20 | S&F TMT steel bars 5mm dia and over, up to and including 10mm dia in stirrups spcers and binders complete all as specified and directed. |
| 21 | M&L Fly ash brick with sub class 'B' bricks straight or curved on plan exc 6m mean radius built in cement mortar 1:6 complete all as specified and directed. |
| 22 | M & L rendering 15mm thick on brick wall or concrete surface in cement mortar 1:6 finished even and smooth without using extra cement complete all as specified and directed. |
| 23 | M & L rendering 15mm thick on brick wall or concrete surface consisting two layers, under layer of 10mm thick in CM (1:6) & top layer of 5mm thick in cement mortar 1:4 mixed with water proofing compound, finished even and smooth without using extra cement complete all as specified and directed. |
| 24 | M & L rendering 5mm thick on ceiling in cement mortar 1:3 finished fair and even smooth without using extra cement complete all as specified and directed. |
| 25 | Material & Labour for preparation of new external surfaces of wall and applying Two or more coats of 100% Premium acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives @ 1.43 litre/ 10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/ 10 sqm over new surfaces complete all as specified and as directed. |
| 26 | M&L for prepareation of new internal surfaces of wall and applying oil emulsion with 1st quality acrylic distemper (ready mixed) having VOC content less than 50 gms/litre, of approved manufacturer, of required shade and colour complete, as per manufacturer's specification. Two or more coats on new work.,over a coat of primer all as specified and directed. |
| 27 | M & L applying two coat of white wash on newly plastered ceiling surfaces including preperation of surfaces, complete all as specified and directed. |
| 28 | M&L for Applying wall care putty on new wall surfaces including rubbing, levelling and preparing the surfaces for receiving further finishes as complete all as specifed and directed |
| 29 | S&F framed work such as grills, gratings etc with ends of bars shouldered and or reiverted or forged into spikes, framed guard bars and similar work conferming to Fe 410-0 or Fe 310-0 complete all as specified and as directed |
| 30 | M&L two coat of synthetic enamel pinting over a coat of red oxide primer incl preparation of steel new surface over 10 cm width or girth complete all as specified and directed. |
| 31 | M&L for Powder coated aluminium (minimum thickness of powder coating 50 micron colored) for shutters/frame of doors, windows & ventilators including providing and fixing hinges/ pivots and making provision for fixing of fittings wherever required including the cost of EPDM rubber/neoprene gasket required (Fittings shall be paid for separately) with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS:1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing/ paneling, C.P. brass/ stainless steel screws all complete as per architectural drawings complete all as specified. |
| 32 | M&L for pressed steel door frame size 125 mm x 60 mm and 1.25 mm thick including necessary fixing lugs, hinges, lock strike platee etccomplete all as specified. |
| 33 | M&L for providing PCC 1:2:4, type B-0 (using 12.50 mm graded stone aggregate) as in filling of pressed steel door frame / ant other door frame and holdfasts including necessary farmwork etc. complete all as specified |
| 34 | SS & F 35 mm thick 2nd class hardwood glazed and skeleton shutters, open rebated and prepared to receive glass, gauze etc (without sash bars) edges of framing plain chamfered or rounded fitted with cut and mitred beads for securing glass etc fitted to chowkhats for doors etc complete all as specified and directed. |
| 35 | S & F factory made 35 mm thick plain, framed, panelled shutters (Two panels) with lock rail and panel of 9 mm thick BWP commercial ply or 12 mm thick veneered particle board with commercial veneering on both faces and size of the members of shutter are as per IS – 1003 (Part – I) made of kiln seasoned & chemically pressure treated 2nd class hardwood rail and style complete all as specified and directed. |
| 36 | S&F Stainless steel wire cloth, 0.36mm nominal dia of wire and average width of aparture 1.40 mm and fixed with stainless steel wire staples.complete all as specified and directed. |
| 37 | S&F 100 mm long aluminium alloy type C-22 butt hinges with galvanised ms hinge pin etc.complete all as specified and directed |
| 38 | S&F 150 mm long aluminium anodised barrel tower bolt and 12 mm dia fixed complete all as specified and directed |
| 39 | S&F 150mm long aluminium anodised handle cast type and fixed complete all as specified and directed |
| 40 | S&F alluminum alloy, anodised, sliding door bolt with hasp & staple (bolt type) and length of 250 mm long etc all as specified and directed |
| 41 | M&L two coat of synthetic enamel paint over new wooden surfaces of any description not otherwise described over 10cm in width or grith over one coat of pink primer including preparation of surfaces complete all as specified and directed. |
| 42 | M & L 75mm th PCC 1:3:6 type C-1 using 20mm graded stone aggregate as in plinth protection finished even and smooth without using extra cement complete all as specified. |
| 43 | M&L Granite(of any type)tiles 16 to 18 mm thick as in any position and similar works over 10mm thick cement screed in CM 1:4, machine cut, bedded and jointed with grey cement slurry and pointed with white cement and pigment to match the shade of granite stone incl cutting, polishing complete all as specified and directed. |
| 44 | S&F aluminium anodised alloy curtain rails 20mm dia fixing with brackets, stops, rollers khob lattu etc complete all as specified and directed. |
| 45 | M&L for Complete removal of existing water proofing treatment of any description and in any position including PCC padding any thickness and cleaning, wire brushing, watering & removal of debris outside Af Stn .complete all as specified and directed. |
| 46 | M&L PCC 1:2:4 type B1 using 40 mm graded stone aggregate as in concrete padding laid to required slope incl finishing the concrete surface fair and even without using extra cement complete all as specified and as directed. |
| 47 | M&L for Apply oil bound bitumen primer @ 0.30 Litre / Sqm manufactured by the same agency as that of APP with density of 0.87 to 0.89 Kg / Litre at 25 degree Celsius on the prepared dry roof surface, complete all as spectified and directed. |
| 48 | M&L APP polymeric membrane min weighting 3kg/sqm and minimum 3mm thick reinforced with polyster non woven fabric(wt not less than 150 gms/sqm laid on primed surfaces by torch application on method complete all as spectified and directed. |
| 49 | M&L for preparation of new surfaces of any description not otherwise described over 10cm width or girth and applying two coats of solar reflective aluminium paint @ 0.10 kg/sqm membrane surfaces complete all as specified and directed. |
| 50 | M&L for 25mm thick PCC 1:2:4 Damp proof course to horizontal or vertical surfaces including necessary formwork complete all as specified and directed |
| 51 | M&Lfor Chequered cement concrete tiles 30cm x 30cm x 25mm thick, set, jointed and pointed in neat cement slurry in floors and pointed with grey cement and no pigment over 20 mm thik screed bed in CM 1:4 complete all as directed. |
| 52 | S&F Aluminium Composite Panel (ACP) of any colour of exterior edge for cladding near entrance of Alucobond/Alstrong/Brand approved equivalent make for external wall / column / canopy cladding in combination of solid / Metallic colours, including all necessary frame work and complete weather sealing. The composite panel should consist of 3mm thermoplastic core of LDPE sandwiched between 2 skins of 0.5mm thick aluminium sheet (alloy designation 310S) making a total panel thickness of 3to4mm. The surface shall be furnished with Lumiflon based flourcarbon coating on top sides and service coating on reverse side. Coatings shall conform to specifications of ECCA /AAMA and conforming to the mechanical properties of panel as per detailed technical specifications. The system shall be fixed using Gl brackets and stainless steel bolts and nuts complete with spring washers and cap nuts and all other necessary accessories. The bracket support shall be designed as per manufactures specification and shall withstand a wind pressure of 150 Kg/Sqm. All hardware shall corrosion resistant frame out of anodised aluminium member. complete all as specified and directed |
| 53 | S&F toughened glass 12mm thick in hinged doors, partitions, automatic doors , stair case panels and similar work incl cutting to shape Complete all as specified and directed. |
| 54 | S & F Material & Labour for providing and fixing stainless steel (Grade 304) railing made of hollow tubes, channels, plates etc., including welding, grinding, buffing, polishing and making curvature (where ever required) and fitting the same with necessary stainless steel nuts and bolts complete, including fixing the railing with necessary accessories & stainless steel dash fasteners, stainless steel bolts etc., of required size, on the top of floor or the side of waist slab with suitable arrangement Complete all as specified and directed. |
| 55 | Providing and fixing factory made uPVG white colour Sliding window Three track made of extruded profiles with wall thickness of 2.3mm (+ -0.2mm). Window profile with hollow section with multi chamber. Frame (88mm x 52mm), sliding sash (42mm x 67mm). Sliding mesh Sash (42mm x 57mm) Sliding interlock (One vertical length in each shutters) (45.5mm x 28mm), Glazing bead (24.5mm x 16mm) will be miterd cut and fusion welded at all corners, including drilling of holes for fixing hardware and drainage of water etc., making arrangement for fixing of hardware. EPDM gasket, 1.2+ -0.2mm thick galvanised steel Frame (30mm x 18mm) 2 nos, sliding sash (30mm x 18mm), sliding mesh sash (26mm x 10mm) profile to be inserted in required profile, frame will be fixed to the wall with 8mm x 100mm long fasteners, Hardware [Touch Lock of zinc alloyed (white powder coated), steel roller system. Stainless steel wire cloth 0.36mm nominal dia of wire and average width of aperture 1.40mm and required accessories. complete all as specified. |
| 56 | Providing and fixing factory made uPVC white colour fixed window for grills made of extruded profiles with wall thickness of 2.3mm(+-0.2mm). Window profile with hollow section with multi chamber. Frame (60mm x 58mm). T profile (Onevertical length in between two shutters) (60mm x 74mm). Glazing bead (35mm x 20mm) will be mitered cut and fusion welded at all corners, including drilling of holes for fixing hardware and drainage of water etc. making arrangement for fixing of hardware, EPDM gasket. 1.2 +–0.2mm thick, galvanized steel Frame (28mm x 21.5mm), T profile (27mm x 17 mrn) to be inserted in required profile, frame will be fixed to the wall with 8mm x 100mm long fasteners- 5mm thick glazing with selected quality glass complete all as specified. |
| 57 | Supply and fixing factory made uPVC door frame made of uPVC. extruded sections having an overall dimension (extruded section profile) 48x40 mm (tolerance ± 1 mm), with wall thickness 2.0 mm (± 0.2 mm), corners of the door frame Jointed with galvanized brackets and stainless steel screws, joints mitred and Plastic welded. The hinge side vertical of the frames reinforced by galvanized M.S. tube of size 19 X 19 mm and 1mm (± 0.1 mm) wall thickness and 3 nos. stainless steel hinges fixed to the frame complete all as specified by the manufacturer and complete all as specified and directed. |
| 58 | Providing and fixing factory made uPVC white colour casement (Openable) Door made of extruded profile wilh wall thickness of 2.3mm ( + -0.2mm). Window profile with hollow section with mitlti chamber, frame (60mm x 58mm), sash (60mm x 78mm). T profile (One vertical length in between two shutters) (60mm x 74mm). Glazing bead (35mm x 20mm) will be mitered cut and fusion welded at all corners, including drilling ol holes for fixing hardware and drainage of water etc., making arrangement for fixing of hardware. EPDM gasket 1.2 + -0.2mm thick galvanized steel Frame (28mm x 21.5mm), sash (31mm x 27mm), T profile (27mm x 17mm) to be inserted in required profile, frame will be fixed to the wall wilh 8mm x 100mm long fasteners. Hardware: [casement door handle made of zinc alloyed (white powder coated). Corner striker. Secondary Strikers. Cylinder. Door transmission gear made of mild sleel with multi point locking system with strikes. 3D Hinges of zinc alloyed (white powder coated) [and 5mm thick glazing with selected quality glass. (Note: The unit rate quoted by contractor excludes cost of glass and includes all other connected accessories. Net opening will be measured for payment purpose.) complete all as specified and directed. |
| 59 | M&L for point wiring complete with FRLS PVC insulated, unsheathed stranded copper conductor of nominal area 1.5 Sqmm, 1100 volts grade, along with one single run of same size and type of copper wire as continuous earth wire to common earth dolly in and including cutting/chasing on brick wall not exc. 10 cm girth (excluding ceiling surface for existing pipe) and supply and fixing concealed PVC conduit pipe medium grade of nominal size 20 mm dia along with connected fittings/junction boxes and sunken terminal boxes pressed MS/GI steel terminal boxes not less than 1.20 mm thick for mounting switch, socket etc including 3 mm thick Hylam brand sunmica laminated sheet cover with brass screw and cup washers with all accessories complete all as specified and directed and suitable for the following: - |
| 60 | (i) One light point or one fan point controlled by one way, single pole switch |
| 61 | (iii) One 3 pin socket out let, 6 amps on the \\"same board\\" with other switches |
| 62 | (iii) One 3 pin socket outlet, 6 Amp on “independent board” |
| 63 | All as per Item No 59 above but with one socket outlet 15 A with 2.5 Sq mm FRLS PVC insulated copper cable |
| 64 | Supply & Fixing switch piano flush button type, 6 Amp one way, 240 Volt, single pole , ISI marked conforming to IS 3854 style double colour series with cover plate complete all as specified and directed. |
| 65 | Supply & Fixing socket out let, 2 in 1, 5 pin, 6 Amp, 240 Volt AC, flush type, |
| 66 | Supply & Fixing switch socket combination 3 in 1, 3 pin 5 & 15 A flush type universal |
| 67 | Supply & Fixing lamp holder poly carbonate body with back plate suitable for batten fittings |
| 68 | Supply & Fixing ceiling rose 3 terminal poly carbonate body |
| 69 | Supply & Fixing stepped type fan regulator flush type complete all as specified and directed. |
| 70 | Supply & Fixing of DB by SPN Distribution Box, double door of protection grade IP 43 in fine powder coated, matt finish with best CRCA sheet, fitted with shrouded neutral, insulated pin type copper bus bar, Din rail, earth bar of 8 way, double door complete all as specified and directed. |
| 71 | Supply & fixing tube light fitting of 20 watt , 4 feet, 230 V , 50 HZ all as specified and directed |
| 72 | Supply & Fixing MCB SPN, 32 Amps 240 volts, AC , 10 KA breaking capacity 'C' Series,\\"ISI marked complete all as specified and directed. |
| 73 | Supply & Fixing MCB SP, 5 to 32 Amps 240 volts, AC , 10 KA breaking capacity 'C' Series,\\"ISI marked complete all as specified and directed. |
| 74 | Supply and fixing LED light fitting 1X 10 Watt bulk head luminairies including LED light driver holder connecting up with three core flexible copper conductor cable of suitable size. |
| 75 | M&L for earthing as per IS:3043 with galvanized steel earth plate electrode 600 x 600 x 6.0 mm thick buried directly in ground (earth pit not less than 2.25 metres deep below ground level) with top edge of the plate not less than 1.5 metre below normal ground level connected to galvanized iron wire 4 mm dia (8 SWG) as earthing lead protected by GI pipe medium grade 15 mm bore for protection of GI earth wire and 20 mm dia GI pipe medium grade for watering with alternate layers of charcoal /coke and salt including all accessories like nut, bolts, reducer, nipple, wire meshed/screened funnel and making brick masonry finished chamber of internal size 300 mm x 300 mm x 300 mm with concrete base, covered with PCC cover which shall be embedded in the block masonry including excavation works, refilling, connected to main switch/MCB DB for feeding the electric supply to domestic quarters compete all as specified as shown in electricall plateNo. 3 of SSR Part-I and testing of earth resistance as required including necessary excavation and earth work. Please Enable Macros to View BoQ information |
AI Tender Summary
Tender Timeline
Jul 16, 2026
11:30 IST
Tender Published
Tender notice published.
CompletedAug 05, 2026
17:00 IST
Bid Submission Deadline
Online submission via eProcurement portal.
Upcoming · 7 daysAug 07, 2026
Bid Opening Date
Technical bids will be opened and evaluated.
Upcoming · 9 daysTender Documents
Download All (ZIP) ↓
Disclaimer
We takes all possible care for accurate & authentic tender information. However users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender