Tender For Iinstallation Of 20.00 Meter High Mast Light In Gram Panchayat Barsada Bujurg, Jakhni, Ghurauda And Anthuwa At Block- Mahua, Distt- Banda
Tender Value
19.56 Lakhs
Estimated cost
Bid Submission
22 Jul 2026
4 days left
EMD
39000
Bank guarantee accepted
Document Fee
5900
Non-refundable
Tender Type
Online
Tender Overview
Organization
Tender ID
Competition Type
NCB
Bidding Type
Tender
Location / State
Banda → Uttar Pradesh
EMD Exemption
Not Available
Quantity
Not Available
Website
Contact Person
Address
Project Description
Tender for Iinstallation Of 20.00 Meter High Mast Light In Gram Panchayat Barsada Bujurg, Jakhni, Ghurauda And Anthuwa At Block- Mahua, Distt- Banda
BOQ
| Sl. No. | Item Description |
| 1 | Providing and fixing 25mm x 5mm GI strip on surface or in recess for connections etc., as required. |
| 2 | 32 Amp TPN 8 way, Distribution tap off box with ISI marked HRC fuses for rising mains. |
| 3 | The pipes of sixes 150mm & below shall be M.S. \\"C\\" Class as per IS:1239 and pipes size above 150mm shall be welded black steel pipe heavy class as per IS:3589, from minimum 6:35 mm thick M.S. sheet for pipes upto 350 mm dia, and from minimum 7m thick MS Sheet for piper of 400 mm dia and above. M.S. Pipe 125 mm dia |
| 4 | Earthling with copper earth plate 600mm x 600mm x 3mm thick including accessories and providing masonry enclosure with cover plate having locking arrangement and watering pipe of 2.70 meter long etc., with charcoal/coke and salt., as required. |
| 5 | Wiring for circuit/submain wiring along with earth wire with the following FRLS PVC insulated copper conductor single core calbe in surface/recessed steel conduit as required. 2x6 sqmm + 1 x 6 sqmm earth wire |
| 6 | Supply & laying of Aluminum conductor PVC insulated armored served sheathed cables 1100 Volts grade at a depth of 750mm below ground level over a cushion of 75mm thick sand all around and protected with brunt bricks of sides and on top. On surface the cable run shall be fixed on M.S. clamps etc, of suitable size or as directed by the Engineer-in-charge, complete in all respect. Including excavation and refilling. The armoring of the cable shall be properly connected with the earth conductor by clamps etc. 25sqmm x 3½ core. |
| 7 | Supply & fixing of 20 Mtr. high mast shaft of approved make with rising system hot dip galvanized, inside and outside, dip heaving pole sheet thickness 4mm, top dia minimum 150mm, bottom dia 410mm base plate 32 mm thick suitable for wind velocity as per IS 875 part 3. There and having no circumferential weld, with accessories for high mast such ahead frame suitable for 6 luminaries and its control gear boxes 1.5 H.P. power toll motor, 3 point suspension system with steel wire rope 6mm dia double from winch, including marking suitable foundation as per manufacture drawing/site regiment along with foundation bolts, nuts, washers, anchor plates etc., complete in all respect. |
| 8 | Supply and fixing of factory wired integral LED flood light luminaries with die cast aluminum housing built with driver set suitable for 200 watt. Confirming to IP 66 protection complete in all respect 204(k)-24000 system lumens, High Power with lenses ˃ 10 Lm/watt, PF˃ 0.95, THD˂10%, at full load, CRI˃440 Volt & ˃ 300 V auto cut and re-start future, 4.0 KV internal surge portion with 5 year warrantee Cat AAA |
| 9 | Supply and erection of factory fabricated and wired metal clad dust and vermin proof floor mounting M.S. Channel Base with bottom and top cable entries electrical control panel with TPN MCCB's (Four pole 36 KA with thermal magnetic release) switches complete and instrument chamber etc. complete in all respects. The instrument chamber shall be separate and shall comprise of flush type digital metering system for phase to phase voltage and single phase voltage, cutter and other parameters (KVA, P.F., KW etc.) in each phase with touch type selector switches for different readings, instrument fuses, current transformer etc. The panel board shall have suitable capacity electrolytic aluminum bus bars as per IS:8623 or above insulated with heat shrink slaving and mounted on non hygroscopic supports such as CMC/BMC support with detachable side covers and shall be suitable for extension on the sides. The MCCB's shall be complete with suitable cable and boxes, compression glands and indicating lamp on incoming etc. The job includes the grounding of the boards as per directions of Engineer-in-Charge. All out goings of 100 Amp. and above shall have an ammeter. The panel board shall be fabricated with CRCA sheet with a minimum thickness of 1.6mm/2mm. Cubicle type switch board shall be Cat A & B only. |
| 10 | GST extra as per applicable Please Enable Macros to View BoQ information |
AI Tender Summary
Tender Timeline
Jul 16, 2026
11:30 IST
Tender Published
Tender notice published.
CompletedJul 22, 2026
17:00 IST
Bid Submission Deadline
Online submission via eProcurement portal.
Upcoming · 4 daysJul 22, 2026
Bid Opening Date
Technical bids will be opened and evaluated.
Upcoming · 4 daysTender Documents
Download All (ZIP) ↓
Disclaimer
We takes all possible care for accurate & authentic tender information. However users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender