Tender For Under Csr Scheme,Construction Work Of Anganwadi Centre Operated Under Child Development And Nutrition Department In Composite School Premnagar Kanpur Nagar And Supply And Installtion Of Materials For Use
Tender Value
28.39 Lakhs
Estimated cost
Bid Submission
29 Jul 2026
14 days left
EMD
28400
Bank guarantee accepted
Document Fee
1770
Non-refundable
Tender Type
Online
Tender Overview
Organization
Tender ID
Competition Type
NCB
Bidding Type
Tender
Location / State
Kanpur Nagar → Uttar Pradesh
EMD Exemption
Not Available
Quantity
Not Available
Website
Contact Person
Address
Project Description
Tender for Under Csr Scheme,Construction Work Of Anganwadi Centre Operated Under Child Development And Nutrition Department In Composite School Premnagar Kanpur Nagar And Supply And Installtion Of Materials For Use
BOQ
| Sl. No. | Item Description |
| 1 | Earth work in excavation by mechanical means (Hydraulic excavator) / manual means i foundation trenches or drains (not exceeding 1.5 ni in width or 10 sqm onplan), including dressing of sides and ramming of bottoms, for all lift, including getting out the excavated soil and disposal of surplus excavated soil as directed, within a lead of 50 m. All kind of soil DSR No. 2.8.1 |
| 2 | Excavating, supplying and filling of local earth (including royalty) bymechanical transport upto a lead of 5km also including ramming and watering of the earth in layers not exceeding 20 cm in trenches, plinth,sides of foundation etc. complete DSR 2.25(a) |
| 3 | Suppluing and filling in plinth with with sand under floors, including watering and ramming cobusolidating and dressing complete DSR 2.27 |
| 4 | Diluting and injecting chemical emulsion anti-termite treatment (excluding the cost of chemical emulsion) : Treatment of soil under existing floors using chemical emulsion@ one litre per hole, 300 mm apart including drilling 12 mm diameter holes and plugging with cement mortar 1 :2(1 cement : 2 Coarse sand) to match the existing floor: With Chlorpyriphos/Lindane E.C. 20% with 1% concentration DSR 2.35.3.1 |
| 5 | Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level 1:4:8 (1 Cement: 4 coarse sand (zone-III) derived from natural sources: 8 graded stone aggregate 40 mm nominal size derived from natural sources)DSR No. 4 1.8 |
| 6 | Providing and laying in position specified grade of reinforced cement concrete, excluding the cost of centering, shuttering, finishing and reinforcement - All work up to plinth level 1:1.5:3 (1 cement : 1.5 coarse sand (zone-III) derived from natural sources : 3 graded stone aggregate 20 mm nominal size de rived from natural sources DSR 5.1.2 |
| 7 | Reinforced cement concrete work in walls (any thickness), including attached pilasters, buttresses, plinth and string courses, fillets, columns, pillars, piers, abutments, posts and struts etc. above plinth level up to floor five level, excluding cost of centering, shuttering, finishing and reinforcement :1:1.5:3 (1 cement : 1.5 coarse sand(zone-III) derived from natural sources : 3 graded stone aggregate 20 mm nominal size derived from natural sources) DSR 5.2.2 |
| 8 | Reinforced cement concrete work in beams, suspended floors, roofs having slope up to 15° landings, balconies, shelves, chajjas, lintels,bands, plain window sills, staircases and spiral stair cases above plinth level up to floor five level, excluding the cost of centering, shuttering,finishing and reinforcement with 1:1.5:3 (1 cement : 1.5 coarse sand(zone-III) derived from natural sources : 3 graded stone aggregate 20 mm nominal size derived from natural sources). DSR 5.3 |
| 9 | Steel reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete upto plinth level Thermo-Mechanically Treated bars of grade Fe-500D or more. DSR 5.22.1 |
| 10 | Centering and shuttering including strutting, propping etc. and removal of 6 form for Foundations, footings, bases of columns, etc. for mass concrete DSR 5.9.1 |
| 11 | Centering and shuttering including strutting, propping etc. and removal of 6 form for Lintels, beams, plinth beams, girders, bressumers and cantilevers DSR 5.9.5 |
| 12 | Centering and shuttering including strutting, propping etc. and removal of 6 form for Columns, Pillars, Piers, Abutments, Posts and Struts DSR 5.9.6 |
| 13 | Centering and shuttering including strutting, propping etc. and removal of 6 form for Suspended floors, roofs, landings, balconies and access platform DSR 5.9.3 |
| 14 | Brick work with common burnt clay F.P.S. (non modular) bricks of class 7 designation 7.5 in foundation and plinth in: Cement mortar 1:6 (1 cernent: 6 coarse sand). DSR-6.1.2 |
| 15 | Brick work with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in superstructure above plinth level up to floor V level in all shapes and sizes in: Cement mortar 1:4 (1 cement: 4 coarse sand) DSR 6.4.1 |
| 16 | 12 mm cement plaster on rough side of single or half brick wall of mix: 9 1:4 (1 cement: 4 coarse sand) including cost of all material, labour, T&P etc. required for proper completion of work. DSR No. 13.4.1 |
| 17 | 15 mm cement plaster on rough side of single or half brick wall of mix: 10 1:4 (1 cement: 4 coarse sand) including cost of all material, labour, T&P etc. required for proper completion of work. DSR No. 13.5.1 |
| 18 | Providing and applying white cement based putty of average thickness 1 mm, of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete. DSR-13.80 |
| 19 | Distempering with Ist quality acrylic distemper, of approved brand and manufacture, including applying additional coats wherever required, to achieve even shade and colour. New work (Two or more coats applied @ 3.84 kg/10 sqm). DSR-13.41.1 |
| 20 | Finishing wall with acrylic smooth exterior paint of required shade New work (Two or more coat applied @ 1.67 ltr/10 sqm over and including priming coat of exterior primer applied @ 2.20 kg/10 sqm) DSR 13.46.1 |
| 21 | Providing and laying vitrified floor tiles in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and 16 conforming to IS: 15622, of approved make, in all colours and shades, laid on 20mm thick cement mortar 1:4 (1 cement: 4 coarse sand), jointing with grey cement slurry @ 3.3 kg/ sqm including grouting the joints with white cement and matching pigments etc., complete Size of Tile 600x600 mm. DSR 11.41.2 |
| 22 | Providing and laying vitrified floor tiles in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and 16 conforming to IS: 15622, of approved make, in all colours and shades, laid on 20mm thick cement mortar 1:4 (1 cement: 4 coarse sand), jointing with grey cement slurry @ 3.3 kg/ sqm including grouting the joints with white cement and matching pigments etc., complete Size of Tile 600x600 mm.Glazed Vitrified tiles Matt/Antiskid finish of size DSR 11.41A.3.1 |
| 23 | Providing and fixing Ist quality ceramic glazed wall tiles conforming to IS: 15622 (thickness to be specified by the manufacturer), of approved make, in all colours, shades except burgundy, bottle green, black of any size as approved by Engineer- in-Charge, in skirting, risers of steps and dados, over 12 mm thick bed of cement mortar 1.3 (1 cement 3 coarse sand) and jointing with grey cement slurry @ 3.3kg per Sqm, including pointing in white cement mixed with pigment of matching shade complete. DSR-8.31 |
| 24 | Providing and laying Ceramic glazed floor tiles of size 300x300 mm (thickness to be specified by the manufacturer) of 1st quality conforming to IS : 15622 of approved make in colours such as White, Ivory, Grey,Fume Red Brown, laid on 20 mm thick cement mortar 1:4 (1 Cement : 4 Coarse sand), Jointing with grey cement slurry @ 3.3 kg/sqm including pointing the joints with white cement and matching pigment etc., complete. DSR 11.37 |
| 25 | Providing and fixing 18 mm thick gang saw cut, mirror polished, premoulded and prepolished, machine cut for kitchen platforms, vanity counters, window sills, facias and similar locations of required size, approved shade, colour and texture laid over 20 mm thick base cement mortar 1:4 (1 cement : 4 coarse sand), joints treated with white cement, mixed with matching pigment, epoxy touch ups, including rubbing, curing, moulding and polishing to edges to give high gloss finish etc. complete at all levels. DSR 8.2.2 |
| 26 | Providing and applying fibre reinforced elastomeric liquid water proofing membrane with resilient acrylic polymers having Sun Reflectivity Index (SRI) of 105 on top of concrete roof in three coats @10.76 litre/ 10 sqm. One coat of self-priming of elastomericwaterproofing liquid (dilution with water in the ratio of 3:1) and twocoats of undiluted elastomeric waterproofing liquid (dry film thickness of complete application/system not less than 500 microns). The operation shall be carried out after scrapping and properly cleaning the surface to remove loose particles with wire brushes, complete in all respect as per the direction of Engineer-in-Charge. DSR 22.22A |
| 27 | Providing and fixing ISI marked flush door shutters conforming to IS 2202 (Part 1 non-decorative type, core of block board construction with frame of 1st class. 17 hard wood and well matched commercial 3 ply veneering with vertical grains or cross bands and face veneers on bothfaces of shutters. 30 min thick including (SI marked Stainless Steel butt hinges with necessary screws DSR 9.21.2 |
| 28 | Extra for providing lipping with 2nd class teak wood battens 25 mm 18 minimum depth on all edges of flush door shutters (over all area of door shutter to be measured). DRS No. 9.23 |
| 29 | Providing and fixing bright finished brass tower bolts (barrel type) withnecessary screws etc. complete :200x 10 mm DSR 9.74.2 |
| 30 | Providing and fixing bright finished brass door latch with necessary screwsetc. complete 300x16x5 mm DSR 9.75.1 |
| 31 | Providing and fixing ISI marked oxidised M.S. sliding door bolts with nuts 21 and screws etc. complete (copper oxidized as per IS: 1378) 300x16 mm DSR 9.62.1 |
| 32 | Providing and fixing bright finished brass handles with screws etc. complete: 125 mm DSR 9.81.1 |
| 33 | Providing and fixing bright finished brass hanging type floor door stoppo with necessary screws, etc complete DSR 9.82 |
| 34 | Providing and fixing angle iron frames for doors, windows and ventilator of mild steel Angle sections of size 35x35x5 mun, joints mitred and welded by angle iron 35x35x5 mm or 35x 5 mm flat pieces to the existing T-iron frame or to the wall with dash fastener, including fixing of necessary but hinges and screws and applying a priming coat of approved steel primer all complete as per the direction of Engineer-In-charge Fabrication of holes door chaukhats nosing DSR 10.31 |
| 35 | Float glass panes 4 mmthick glass pane (weight not less than 10 kg/sqm) DSR 9.7.7.1 |
| 36 | Finishing with Deluxe Multi surface paint system for interiors andexteriors using Primer as per manufacturers specifications. Painting Steel work with 26 Deluxe Multi Surface Paint to give an even shade. Two or more coat applied @ 0.90 1tr/10 sqm over an under coat of primer applied @080 Itr/10 sqm of approved brand and manufacture DSR-13.48.3 |
| 37 | Providing and fixing stainless steel (Grade 304) railing made of Hollow tubes channels, plates etc, including welding, grinding, bufling, polishing and making curvature (wherever required) and fitting the same with necessary stainless stee 27 nuts and bolts complete, i/c fixing the railing with necessary accessories & stainless steel dash fasteners, stainless steel bolts etc., of required size, on the top of the floor or the side of waist slab with suitable arrangement as per approval of Engineer-in-charge as per Sl no-10.28 |
| 38 | Chequerred precast cement concrete tiles 22 mm thick in footpath & courtyard jointed with neat, cement slurry mixed with pigment to match the shade of tiles 23 including rubbing and cleaning ete complete, on 20 mm thick bed of ca mortar 14 (1 cement: 4 coarse sand) Light shade pigment using white cemen per SI No-11 20.1 |
| 39 | Making plinth protection 50mm thick of cement concrete 1:3.6 (1 cement 3 coarse sand (zone- II) derived from natural sources 6 graded stone aggregate 20 inm nominal size derived from natural sources) over 75mm thick bed of dry brick ballast 40 mm nominal size, well rammed and consolidated and grouted with fine sand, including necessary excavation, levelling & dressing & finishing the top smooth DSR 4.17 |
| 40 | Providing and fixing on wall face unplasticised Rigid PVC rain water 13 pipes conforming to IS: 13592 Type A, including jointing with seal ring conforming to IS: 5382, leaving 10 mm gap for thermal expansion, (i) Single socketed pipes. 110 mm diameter. DSR 12.41.2 |
| 41 | Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, i/c fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and the cost of cutting chases and making good the same including testing of joints complete as per direction of Engineer in Charge. Concealed work, including cutting chases and making good the walls etc. 15 mm dia DRS 18.8.1 |
| 42 | Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, i/c fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and the cost of cutting chases and making good the same including testing of joints complete as per direction of Engineer in Charge. Concealed work, including cutting chases and inaking good the walls etc.25 mm Nosminal dia Pipes DSR-18.8.3 |
| 43 | Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, i/c fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and the cost of cutting chases and making good the same including testing of joints complete as per direction of Engineer in Charge. Concealed work, including cutting chases and inaking good the walls etc. 50 mm Nosminal dia Pipes DSR-18.9.6 |
| 44 | Providing and fixing C.P. brass long nose bib cock of approved quality 33 conforming to IS standards and weighing not less than 810 gms. 15 mm Nosminal bore, DSR-18.50.1 |
| 45 | Providing and fixing C.P. brass stop cock (concealed) of standard design and of approved make conforming to IS:8931.15 mm Nosminal bore. DSR-18.52.1 |
| 46 | Providing and fixing C.P. brass angle valve for basin mixer and geyser points of approved quality conforming to IS:8931 15 mm Nosminal bore. DSR-18.53.1 |
| 47 | Providing and fixing wash basin with C.I. brackets, 15 mm C.P. brass pillar taps 32 min C.P. brass waste of standard pattern, including painting of fittings and 35 brackets, cutting and making good the walls wherever require. White Vitreous China Wash basin size 630x450 mm with a pair of 15 mm C.P. brass pillar taps DSR 17.7.1 |
| 48 | Providing and fixing white vitreous china pedestal type water closet (European type) with seat and lid, 10 litre low level white vitreous china flushing cistern & CP flush bend with fittings & C.L. brackets, 40 mm flush bend, overflow 36 arrangement with specials of standard make and mosquito proof coupling of approved municipal design complete, including painting of fittings and brackets, cutting and making good the walls and floors wherever required: pan with ISI marked white solid plastic seat and lid DSR-17.3.1 |
| 49 | Providing and fixing water closet squatting pan (Indian type W.C. pan ) with 100 mm sand cast Iron P or S trap, 10 litre low level whiteP.V.C. flushing cistern, including flush pipe, with manually controlleddevice (handle lever) conforming to IS : 7231, with all fittings andfixtures complete, including cutting and making good the walls and floors wherever required: White Vitreous china Orissa pattern W.C. pan of size 580x440 mm with integral type foot rests DSR 17.1.1 |
| 50 | Providing and placing on terrace (at all floor levels) polyethylene water storage tank, IS 12701 marked, with cover and suitable locking arrangement and 37 making necessary holes for inlet, outlet and overflow pipes but without fittings and the base suppor DSR 18.48 |
| 51 | Providing and fixing kitchen sink with C.I brackets, C.P. brass chain with rubberplug, 40 mm CP. brass waste complete, including painting the fittings and brackets, cutting and making good the walls wherever required: 1791 White glazed fire clay kitchen sink of size 600x450x 250 mm DSR-17.9.1 |
| 52 | supply & fixing Swr pipe 100 mm dia.(M/R) |
| 53 | supply & fixing Swr pipe 150 mm dia.(M/R) |
| 54 | Construction of granular sub-base by providing close graded Material conforming to specifications, mixing in a mechanical mix plant at OMC, carriage of mixed material by tippers to work site, for all leads& lifts, spreading in uniform layers of specified thickness with motorgrader on prepared surface and compacting with vibratory power roller to achieve the desired density, complete as per specifications and directions of Engineer-in-Charge With material conforming to Grade-III (size range 26.5 mm to0.075 mm) having CBR Value-20 DSR 16.78.3 |
| 55 | Providing and laying factory made chamfered edge Cement Concrete paver blocks in footpath, parks, lawns, drive ways or light traffic parking etc, of required strength, thickness & size/ shape, made by table vibratory method using PU mould, laid in required colour & pattern over 50mm thick compacted bed of sand, compacting and proper embedding/laying of inter locking paver blocks into the sand bedding layer through vibratory compaction by using plate vibrator, filling the joints with sand and cutting of paver blocks as per required size and pattern, finishing and sweeping extra sand. complete all as per direction of Engineer-in-Charge 80 mm thick C.C. paver block of M-30 grade with approved color design and pattern. DSR-16.91.2 |
| 56 | Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level : 1:2:4 (1 cement : 2 coarse sand (zone-III) derived from natural sources : 4 graded stone aggregate 20 mm nominal size derived from natural sources) DSR 4.1.3 |
| 57 | Steel work in built up tubular (round, square or rectangular hollow tubes etc.) trusses etc., including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer, including welding and bolted with special shaped washers etc. complete Hot finished welded type tubes DSR 10.16.1 |
| 58 | Manufacturing, supplying and fixing retro reflective overhead signage boards made up of 2 mm thick aluminium sheet, face to be fully covered with high intensity and encapsulated lens type heat activated retro reflective sheeting conforming to type - III of ASTM-D-4956-01 as approved by Engineer-in-charge, letters, borders etc. as per IRC: 67-2001 in silver white with blue colour back ground and with high intensity grade, pasted on substrate by pressure sensitive adhesive backing which shall be activated by applying pressure conforming to class II of ASTM-D-4956-01 and fixing the same to the plate of structural frame work by means of suitable sized aluminium alloys, rivets or bolts & nuts @ 300 mm centre to centre all along the periphery as well as in two vertical rows along with theft resistant measures, including the cost of painting with two or more coats of epoxy paint in grey colour on the back side of aluminium sheet including appropriate priming coat. The rate includes the cost of rounding off the corners, lowering down the structural frame work from the gantry, fixing and erecting the same in position all completeas per drawings, specification and direction of the engineer-incharge.( Structural frame work including M.S. plate to be provided separately. Rectangular area of the sheet only shall be measured for payment DSR16.60 |
| 59 | Providing and fixing in position collapsible steel shutters with vertical channels 20x10x2 mm and braced with flat iron diagonals 20x5 mm size, with top and bottom rail of T-iron 40x40x6 mm, with 40 mm dia steel pulleys, complete with bolts, nuts, locking arrangement, stoppers, handles, including applying a priming coat of approved steel primer. DSR 10.3 |
| 60 | Submersible pump |
| 61 | Supply of 110 mm dia PVC pipe of ISI Mark 6 kg /cm2 strenth quality. |
| 62 | Supply of 32 mm dia B Class G.I. pipe in 3.0 mtr length |
| 63 | 110 mm dia Boring drilling complete in all respect as per following stages |
| 64 | from GL to 30 mtr |
| 65 | from 30 mtr to 60 mtr |
| 66 | Lowering & jointing of PVC pipe all Labour T & P etc all complete. |
| 67 | from GL to 30 mtr |
| 68 | from 30 mtr to 60 mtr |
| 69 | Lowering of plant with motor pump set testing,commissioning of pump set with cortage and handling of material complete. |
| 70 | Supply of following items for proper completion of work. |
| 71 | Supply of 1.00 H.P. KSB make submersible motor pump set, discharge 2000 ltr.hr at the head of 45 meter etc including supply of suitable submersible cable & wire rope etc all complete. |
| 72 | Supply of cable 3 Core 2.5 sqr mm (Copper) |
| 73 | Supply of cable 3 Core 2.5 sqr mm (al.) |
| 74 | M.S.Clamp 110 mm dia |
| 75 | M.S.Clamp 32 mm dia |
| 76 | Solution |
| 77 | GI long screw 20mm |
| 78 | Adopter |
| 79 | Socket |
| 80 | Nipple 75 mmx20 mm |
| 81 | Boring cap |
| 82 | Gate Valve 25 mm |
| 83 | Nut Bolt |
| 84 | Elbow 25 mm |
| 85 | Nipple 100 mm x 25 mm |
| 86 | Supply/Fixing of star delta starter control panel with board. |
| 87 | Electrification |
| 88 | Wiring for light point/ fan point/ exhaust fan point/ call bell point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable in surface/ recessed medium class PVC conduit,with modular switch, modular plate, suitable GI box and earthing the point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable etc. as required. DSR 1.10.3 |
| 89 | Group C |
| 90 | Wiring for circuit/ submain wiring alongwith earth wire with the following sizes of FRLS PVC insulated copper conductor, single core cable in surface/ recessed medium class PVC conduit as required. 2 X 2.5 sq. mm + 1 X 2.5 sq. mm earth wire DSR 1.14.2 |
| 91 | Supplying and fixing two module stepped type electronic fan regulator on the existing modular plate switch box including connections but excluding modular plate etc. as required. DSR 1.25 |
| 92 | Supplying and fixing suitable size GI box with modular plate and cover in front on surface or in recess, including providing and fixing 3 pin 5/6 A modular socket outlet and 5/6 A modular switch, connections etc. as required. DSR 1.31 |
| 93 | Supplying and fixing suitable size GI box with modular plate and cover in front on surface or in recess, including providing and fixing 6 pin 5/6 & 15/16 A modular socket outlet and 15/16 A modular switch, connections etc. as required. DSR 1.32 |
| 94 | Installation of exhaust fan in the existing opening, including making good the damage, connection, testing, commissioning etc. as required. Upto 450 mm sweep DSR 1.50.1 |
| 95 | Supplying & fixing suitable size GI box wih modular plate and cover in front on surface or in recess including providing and fixing 25 A modular socket outlet and 25 A modular SP MCB, \\"C\\" curve including connections, painting etc. as required. (for A.C. Point/MCB Point) DSR 1 .57 |
| 96 | Supplying and fixing following way, horizontal type three pole and neutral (TPN), sheet steel, MCB distribution board, 415 V, on surface/ recess, complete with tinned copper bus bar, neutral bus bar, earth bar, din bar, interconnections, powder painted including earthing etc. as required. (But without MCB/RCCB/Isolator) DSR 2.4.2 |
| 97 | 6 way (4 + 18), Double door |
| 98 | Supplying and fixing 5 A to 32 A rating, 240/415 V, 10 kA, \\"C\\" curve, miniature circuit breaker suitable for inductive load of following poles in the existing MCB DB complete with connections, testing and commissioning etc. as required. DSR 2.10.1 |
| 99 | Single pole |
| 100 | S/F of changeover switch on angle iron frame 100 Amp 5 pole … complete. PWD SOR 2018 378 |
| 101 | Earthing with G.I. earth plate 600 mm X 600 mm X 6 mm thick including accessories, and providing masonry enclosure with cover plate having locking arrangement and watering pipe of 2.7 metre long etc. with charcoal/ coke and salt as required.DSR 5.4 |
| 102 | Supplying and laying 25 mm X 5 mm G.I strip at 0.50 metre below ground as strip earth electrode, including connection/ terminating with G.I. nut, bolt, spring, washer etc. as required. (Jointing shall be done by overlapping and with 2 sets of G.I. nut bolt & spring washer spaced at 50mm) DSR 5.9 |
| 103 | Providing and laying earth connection from earth electrode with 6 SWG dia G.I. Wire in 15 mm dia G.I. pipe from earth electrode including connection with G.I. thimble excavation and re-filling as required. DSR 5.12 |
| 104 | Supply, Installation, Testing and Commissioning of 1200 mm sweep, BEE 5 star rated, ceiling fan with Brush Less Direct Current (BLDC) Motor, class of insulation: B, 3 nos. blades, 30 cm long down rod, 2 nos. canopies, shackle kit, safety rope, copper winding, Power Factor not less than 0.9, Service Value (CM/M/W) minimum 6.00, Air delivery minimum 210 Cum/Min , 350 RPM (tolerance as per IS : 374-2019), THD less than 10%, remote or electronic regulator unit for speed control and all remaining accessories including safety pin, nut bolts, washers, temperature rise=75 degree C (max.), insulation resistance more than 2 mega ohm, suitable for 230 V, 50 Hz, single phase AC Supply, earthing etc. complete as required. DSR 19.1 |
| 105 | S/F of 1x22 LED Tubelight ….......... Completed 1403 |
| 106 | Supply & fixing of 225/300mm sweep ventilating (Light Duty) exhaust fan complete with Metallic Blade (Steel bird guard protector /Copper motor for high air suction performance /Capacitor etc.), Noise level : (45 - 50) dB, Power consumption : 45 W, Rated voltage : 230 V, Rated frequency : 50 Hz, Motor type : Normal Speed. Complete in all respect. |
| 107 | Providing and fixing of Ecce kit (M/R) |
| 108 | Provinding and fixing of LED TV,R.O Purifier,Wall Painting and Swing. (M/R) |
| 109 | Provinding and fixing of Funiture ( 01 Almirah ,01 Table And 02 chair) (M/R) |
| 110 | Supply Child Kit (M/R) |
| 111 | Boundary wall |
| 112 | Earth work in excavation by mechanical means (Hydraulic excavator) / manual means i foundation trenches or drains (not exceeding 1.5 ni in width or 10 sqm onplan), including dressing of sides and ramming of bottoms, for all lift, including getting out the excavated soil and disposal of surplus excavated soil as directed, within a lead of 50 m. All kind of soil DSR No. 2.8.1 |
| 113 | Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level 1:4:8 (1 Cement: 4 coarse sand (zone-III) derived from natural sources: 8 graded stone aggregate 40 mm nominal size derived from natural sources)DSR No. 4 1.8 |
| 114 | Providing and laying in position specified grade of reinforced cement concrete, excluding the cost of centering, shuttering, finishing and reinforcement - All work up to plinth level 1:1.5:3 (1 cement : 1.5 coarse sand (zone-III) derived from natural sources : 3 graded stone aggregate 20 mm nominal size de rived from natural sources DSR 5.1.2 |
| 115 | Reinforced cement concrete work in walls (any thickness), including attached pilasters, buttresses, plinth and string courses, fillets, columns,pillars, piers, abutments, posts and struts etc. above plinth level up to floor five level, excluding cost of centering, shuttering, finishing and reinforcement : 1:1.5:3 (1 cement : 1.5 coarse sand(zone-III) derived from natural sources : 3 graded stone aggregate 20 mm nominal size derived from natural sources) DSR 5.2.2 |
| 116 | Steel reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete upto plinth level Thermo-Mechanically Treated bars of grade Fe-500D or more. SI No. Ch 5.22.6 |
| 117 | Centering and shuttering including strutting, propping etc. and removal of 6 form for Foundations, footings, bases of columns, etc. for mass concrete DSR 5.9.1 |
| 118 | Centering and shuttering including strutting, propping etc. and removal of 6 form for Lintels, beams, plinth beams, girders, bressumers and cantilevers DSR 5.9.5 |
| 119 | Centering and shuttering including strutting, propping etc. and removal of 6 form for Columns, Pillars, Piers, Abutments, Posts and Struts DSR 5.9.6 |
| 120 | Brick work with common burnt clay F.P.S. (non modular) bricks of class 7 designation 7.5 in foundation and plinth in: Cement mortar 1:6 (1 cernent: 6 coarse sand). DSR-6.1.2 |
| 121 | Brick work with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in superstructure above plinth level up to floor V level in all shapes and sizes in: Cement mortar 1:4 (1 cement: 4 coarse sand) DSR 6.4.1 |
| 122 | 12 mm cement plaster on rough side of single or half brick wall of mix: 9 1:4 (1 cement: 4 coarse sand) including cost of all material, labour, T&P etc. required for proper completion of work. DSR No. 13.4.1 |
| 123 | 15 mm cement plaster on rough side of single or half brick wall of mix: 10 1:4 (1 cement: 4 coarse sand) including cost of all material, labour, T&P etc. required for proper completion of work. DSR No. 13.5.1 |
| 124 | Providing and applying white cement based putty of average thickness 1 mm, of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete. DSR-13.80 |
| 125 | Finishing wall with acrylic smooth exterior paint of required shade New work (Two or more coat applied @ 1.67 ltr/10 sqm over and including priming coat of exterior primer applied @ 2.20 kg/10 sqm) DSR 13.46.1 |
| 126 | Providing and fixing angle iron frames for doors, windows and ventilator of mild steel Angle sections of size 35x35x5 mun, joints mitred and welded by angle iron 35x35x5 mm or 35x 5 mm flat pieces to the existing T-iron frame or to the wall with dash fastener, including fixing of necessary but hinges and screws and applying a priming coat of approved steel primer all complete as per the direction of Engineer-In-charge DSR 10.31 Fabrication of holes door chaukhats nosing |
| 127 | Finishing with Deluxe Multi surface paint system for interiors andexteriors using Primer as per manufacturers specifications. Painting Steel work with 26 Deluxe Multi Surface Paint to give an even shade. Two or more coat applied @ 0.90 1tr/10 sqm over an under coat of primer applied @080 Itr/10 sqm of approved brand and manufacture DSR-13.48.3 |
| 128 | Less 5% due to Department Charges Please Enable Macros to View BoQ information |
AI Tender Summary
Tender Timeline
Jul 15, 2026
11:30 IST
Tender Published
Tender notice published.
TodayJul 29, 2026
17:00 IST
Bid Submission Deadline
Online submission via eProcurement portal.
Upcoming · 14 daysJul 30, 2026
Bid Opening Date
Technical bids will be opened and evaluated.
Upcoming · 15 daysTender Documents
Download All (ZIP) ↓
Disclaimer
We takes all possible care for accurate & authentic tender information. However users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender