Tender For Repair / Maintenance Of External Water Supply System, Including Cleaning /Painting Of Oh & Ug Sump Repair To Pumping Installation And Disinfection System At Nofra, 30M & Aqaw (A) And Under Ge (P) No - 01 Jabalpur.
Tender Value
10.50 Lakhs
Estimated cost
Bid Submission
05 Aug 2026
21 days left
EMD
21000
Bank guarantee accepted
Document Fee
500
Non-refundable
Tender Type
Online
Tender Overview
Organization
Tender ID
Competition Type
NCB
Bidding Type
Tender
Location / State
Jabalpur → Madhya Pradesh
EMD Exemption
Not Available
Quantity
Not Available
Website
Contact Person
Address
Project Description
Tender for Repair / Maintenance Of External Water Supply System, Including Cleaning /Painting Of Oh & Ug Sump Repair To Pumping Installation And Disinfection System At Nofra, 30M & Aqaw (A) And Under Ge (P) No - 01 Jabalpur.
BOQ
| Sl. No. | Item Description |
| 1 | Repair to water supply pipeline,distribution system such as arresting the leakage,minor repairs to motor/starter/pump,arresting the leakage of sluice valve/gate valve,rectifying the air lock problem in supply/distribution line etc. by replacing the U/S parts/fixtures in order to maintain the distribution system functional in all manners,all as directed by engineer-in- charge.Note:- The fittings/fixtures required shall be measured under relevent items of schedule complete all as spccified and directed |
| 2 | Taking up or down steel tubing and connections including removal from site complete all as spccified and directed of following sizes :- |
| 3 | (a) 20 mm bore |
| 4 | (b) 25 mm bore |
| 5 | (c) 40 mm bore |
| 6 | (c) 50 mm bore |
| 7 | Supply laying and fixing GI tubing of following sizes medium grade ISI Marked with all necesary fittings laid in trenches complete all as spccified and directed. |
| 8 | (a) 20 mm dia |
| 9 | (b) 25 mm dia |
| 10 | (c) 40 mm dia |
| 11 | (d) 50 mm dia |
| 12 | Supply laying and fixing GI tubing of following sizes medium grade ISI Marked with all necesary fittings fixed to walls. Ceiling or laid in floors complete all as spccified and directed. |
| 13 | (a) 20 mm dia |
| 14 | (b) 25 mm dia |
| 15 | (c) 40 mm dia |
| 16 | (d) 50 mm dia |
| 17 | Supply and and fixing in replacement Gun metal/brass, globe or gate valves with iron wheel head, screwed both ends for iron pipe complete all as spccified and directed of following sizes :- |
| 18 | (a) 20 mm bore |
| 19 | (b) 25 mm bore |
| 20 | (c) 40 mm bore |
| 21 | (d) 50 mm bore |
| 22 | Supply and lower in replacement of casing pipe, tubing GI heavy grade 50mm dia Nominal internal bore one end connected to submersible pump ,complete all as specified and directed. |
| 23 | M&L for taking out casing pipe of max. dia 50 mm from existing borewell by using tripod stand & pulley assembly , max length of pipe not more than 100 mtr complete all as specified and as directed. |
| 24 | Suuply and fix WIRE ROPE, stranded, 6MM, S.S, GRADE-304 to submersible pump set as safey support including neccesary fixing arrangements complete all as specifie and as directed. |
| 25 | Supply & fix in replacement of Non return Valve, flanged of class supplied and installed complete, size 50 mm dia of following sizes complete all as specifie and as directed. |
| 26 | Supply and fix in replacement of brass Foot Valve conforming to IS 4038, 50 mm dia of following sizes complete all as specifie and as directed. |
| 27 | M&L for cutting Ductile iron / Cast iron water mains of size 150/ 100/80 mm dia pipes and reducing to required length for insertion of new tees/branches of pipe before laying including fixing, jointing and testing cast iron fittings such as bends any type radius and angle) tappers, collars, tee, Y junctions, plugs , caps and connected pieces of any other special required at site for the flanged /spigot and socket pipes up to 100 mm bore and connect and joint with existing line complete all as specified and directed.Note: Fittings will be measured and paid separataey. |
| 28 | Dismantling existing valve chambers & Material and labour for construction of valve pit chambers of size 900 X 900 X 900 mm (internal dimensions) as under provided with 10 cm thick PCC 1:4:8 type D-2 as in foundation over 15 cm thick hard core, 23 cm thick brick walls built in cement mortar 1:4, 15 mm thick internal plaster including top of floor, externally upto 150 mm below GL in CM 1:3 finished even and smooth without using extra cement, 3.00 mm thick MS sheet cover with 40 X 40 X 6 mm MS angle frame fixed in PCC 1:2:4 type B1, 50 mm thick coping with 25 X 6 mm flat iron hold fasts, hinges, handles, locking arrangements and applying 2 coats of syntheric enamel paint over acoat of red oxide primer to all steel surfaces and 3 coats of white wash to internal surfaces of chamber including excavation and earth work in any type of soil and removing of surplus soil to a distance not exceeding 50 m complete all as specified and directed. |
| 29 | Dismantling existing valve chambers & Material and labour for construction of valve pit chambers of size 1200 X 1200 X 1200 mm (internal dimensions) as under provided with 10 cm thick PCC 1:4:8 type D-2 as in foundation over 15 cm thick hard core, 23 cm thick brick walls built in cement mortar 1:4, 15 mm thick internal plaster including top of floor, externally upto 150 mm below GL in CM 1:3 finished even and smooth without using extra cement, 3.00 mm thick MS sheet cover with 40 X 40 X 6 mm MS angle frame fixed in PCC 1:2:4 type B1, 50 mm thick coping with 25 X 6 mm flat iron hold fasts, hinges, handles, locking arrangements and applying 2 coats of syntheric enamel paint over acoat of red oxide primer to all steel surfaces and 3 coats of white wash to internal surfaces of chamber including excavation and earth work in any type of soil and removing of surplus soil to a distance not exceeding 50 m complete all as specified and directed. |
| 30 | Supply and fixing in repairs CI body sluice valve class PN 1.6 with flanged ends of size 100mm bore having stainless steel spindle, CI gate with brass ring, operating wheel cast iron cape and connecting accessories etc complete all as specified and directed. |
| 31 | Supply and fixing in repairs CI body sluice valve class PN 1.6 with flanged ends of size 80 mm bore having stainless steel spindle, CI gate with brass ring, operating wheel cast iron cape and connecting accessories etc complete all as specified and directed. |
| 32 | Supply and fix in repair fully automatic star-delta starter suitable for7.5 HP submersible pump set,panel mounted type of required current rating with single phase preventer, phase imbalance, phase reversal short circuit protection with ON - OFF trip indication and dry run preventor complete all as specified and directed. |
| 33 | Supply and fix in repair fully automatic DOL starter suitable for 3HP mono block pump set,panel mounted type of required current rating with single phase preventer, phase imbalance, phase reversal short circuit protection with ON - OFF trip indication and dry run preventor complete all as specified and directed. |
| 34 | Supply and fix in repair fully automatic DOL starter suitable for 2HP HP mono block pump set,panel mounted type of required current rating with single phase preventer, phase imbalance, phase reversal short circuit protection with ON - OFF trip indication and dry run preventor complete all as specified and directed. |
| 35 | Taking out centrifugal pumping set upto7.5 HP, three Phase from foundation ,transporting to workshop opening for inspecting all parts to identify defective parts cleaning and keeping aside serviceable parts in safe custody, rewinding with super enamelled copper wire as per existing size and general servicing/overhauling of pump , electric motor & Re-assembling of motor and pump, transporting back to pump house and connecting with pipes and electric connections and testing for performance complete all as specified and directed.(Note : Parts to be replaced measured separately) |
| 36 | Supply only ball bearing of monoblock motor suitable for upto 7.5HP submersible pump set complete all as specified and directed. |
| 37 | Supply only gun metal impeller of existing size of capacity upto 7.5 HP complete all as specified and directed. |
| 38 | Supply only ss shaft of existing size of capacity upto 7.5 HP complete all as specified and directed. |
| 39 | M&L for old rusted casing of existing size of capacity 7.5 HP complete all as specified and directed. |
| 40 | Rewinding centrifugal mono block pump set/ submmerssible pumping set upto7.5 HP, three Phase taken from borewell ,transporting to workshop opening for inspecting all parts to identify defective parts cleaning and keeping aside serviceable parts in safe custody, rewinding with super enamelled copper wire as per existing size and general servicing/overhauling of pump , electric motor & Re-assembling of motor and pump, transporting back to pump house and connecting with pipes and electric connections and testing for performance complete all as specified and directed. (Note : Parts to be replaced measured separately) |
| 41 | Supply only of following parts of centrifugal pump of capacity 7.5 HP complete all as specifie and as directed. |
| 42 | (a) Stuffing box suitable for 7.5 HP |
| 43 | (b) Stainless steel shaft suitable for 7.5 HP |
| 44 | (c) Shaft sleeve made out of stainless steel for 7.5 HP |
| 45 | (d) Impellar suitable for 7.5 HP |
| 46 | (e) Bearing suitable for 7.5 HP |
| 47 | Rewinding to Booster pump set of capacity UPTO 2/3 HP of any make with super enameled copper winding wire PVC coated of same gauge, Providing PVC separators , PVC sleeves & jointing compound as specified and directed. Note :- Replaced items will be measured and paid seprately under relevent item.If the same motor copper winding wiring burnt second time in the above CA Period, The contractor is responsible to paid and rewind the same at their own cost. complete all as specifie and as directed. |
| 48 | Supply only of following parts of centrifugal pump of capacity 3 HP complete all as specifie and as directed. |
| 49 | (a) Stuffing box suitable for 2/3 HP |
| 50 | (b) Stainless steel shaft suitable for 2/3 HP |
| 51 | (c) Shaft sleeve made out of stainless steel for 2/3 HP |
| 52 | (d) Impellar suitable for 2/3 HP |
| 53 | (e) Bearing suitable for 2/3 HP |
| 54 | Taking out submersible pump set of capacity upto 7.5 HP of different places and M & L for Flushing out / desilting of the bore well by using compresser hydro pressure jet for six hours till clear the silt in the casing pipe by achiving clear water, and washing with hydro pressure jet using foam/oils, disinfecting the bore using sodium hypochloride solution and washing out till water is obtained to the required turbidity (clean water) to the entire satisfacton complete all as specified and directed. |
| 55 | Cleaning and removing of all silt, dirt, mud, etc. from inside the over head tank reservoirs of capacity 100000 gallons and 14 metre staging, inside and out side of wall, mouth of inlet and outlet pipe, removing disposal of the same to a distance not exc. 50 m and applying one coat of white wash on internal surfaces including preparation of old and wet surfaces and sign, writing with white enamelled paint on black back ground, height of letters not less than 7.50 cm on column showing capacity of tank and date of cleaning complete all as directed. Note:- (i) Cleaning shall be done by high pressure rotary jet machine and washing with bleaching powder. (ii) OH Tank base debris / slug cleaned by vaccume cleaning(iii) OH Tank clean by high ultra voilet rediation for removing beeteria and virous (iv) The inlet/ outlet/ overflow pipe of OH tank/ sump shall be cleaned properly and care should be taken to prevent entry/accumulation of sludge into pipe line by blocking mouth of pipe. Any blockage of the inlet/ outlet/ overflow pipe line shall be found to be cleared without any extra cost and the cost of the same shall be deemed to be included in the unit rate quoted.(v) Writing the following words with white paint on black painted back ground to match with existing size and pattern :- (a) CLEANED ON:- ------ (b) NEXT DUE DATE OF CLEANING:- --------- |
| 56 | All as per item No. 29 here in before but Semi UG sump of capacity upto 5000 gallons. complete all as specifie and directed. |
| 57 | Supply and fix in repair MS spindle of existing size 100 mm (4\\"dia) duly threaded with nut (Gutka) as per sample including replacement of rubber packing with nut and bolts complete all as specified and directed. |
| 58 | Supply and fix in repair MS spindle of existing size 80 mm (3\\"dia) duly threaded with nut (Gutka) as per sample including replacement of rubber packing with nut and bolts complete all as specified and directed. |
| 59 | Supply and fix in repairs PVC insulated and PVC sheathed multi stranded copper conductor cable, conforming to IS - 7098 (Part- I) of size 3 core 4 sqmm, 1100 volts grade including necessary water proof connection to submersible pump at cable lead complete all as specified and directed. |
| 60 | Testing of Borewells water with following test to be done and certified by authorised government central/state agencies :-TDS,Chloride,Floride,Alkaline,E-COLI(bacteriological test). complete all as specifie and as directed. |
| 61 | Repair and maintainance of Doser of 100 litres with following specifications:-Doser pump 0.9 Amp,250 volts 100psi,Doser motor 0.8 Amp,220 volts,PVC pipe connection inlet to Doser and outlet to Doser,cleaning of Doser tank,all as per required and directed by engg in charg.Note:- Defective items if replaced shall be measured and paid under relavent item complete all as specifie and as directed. |
| 62 | Supply only against item no. 35 nozzle injector suitable for 100 ltrs Dosing system,complete all as specified and directed. |
| 63 | Supply only against item no. 35 Suction PVC pipe suitable for 100 ltrs Dosing system,complete all as specified and directed. |
| 64 | Excavation in trenches in any type of soil n exc 1.5 mtr in width and n. exc 1.5 mtr in depth and getting out all as required for laying of cables complete all as specifie and directed. |
| 65 | Returning filling, in including spreading ,leveling, watering and well ramming in layers not exc 25 cm each all as required complete all as specifie and directed. |
| 66 | Removing excavated material to a distance not exceeding 50 meters and depositing where directed at a level not exc 1.5 mtr above the starting point complete all as specified and directed. |
| 67 | Earthing complete with galvanised steel earth plate electrode of size 60cm X 60cm X 6mm buried directly in ground (earth pit not less than 2.25 metres deep below the normal ground level) with top edge of the plate not less than 1.5m below normal GL connected to GI earth strip 32mm X 6 mm by means of GI bolts, nuts, check nuts and washers and earth strip protected by 40 mm dia GI pipe medium grade and connected to main distribution board/ earthing test point all as shown on electrical plate No.3 of SSR Part- I including testing on completion including excavation, earth work in hard/ dense soil, plain cement concrete 1:3:6 mix, type C1 pit, 40mm thick RCC 1:2:4 mix, type B1, cover reinforced with 8mm dia TMT bars @ 150mm C/C both ways, GI funnel with watering pipe, wire mesh, protection pipe for earth lead complete all as directed. Notes: Earth strip and protection pipe beyond 7.5m shall be measured and paid separately. complete all as specified and directed. |
| 68 | M&L for fabrication, supply and installation of the Back lit Glow sign board as per following Specifications:-:(a) Box:1 The box size is approx 10 feet x 2.5 feet.2 The board frame should be made of MS Pipe 25x25x1.5 mm painted with one coat red oxide primer and 2 coat synthetic enamel paint.3 Top, Bottom and Side cover shall be made of 26 SWG GI sheet with powder coating and Back side of the board shall be covered with 26 SWG plain GI sheet fixed with rivet and screws.(b) Lighting/Illumination:1. Minimum one LED tube light set is to be provided per five Square feet of board area.2. Complete tube light set is to be provided. Tube lights shall be of reputed make.3. Only copper wiring will be used.(c) Flex:1. Backlit Flex should be of LG Hi-Flex.2. Writing work etc. should be digitally printed. Printing details will be provided by the department.(d) Installation:1 No separate installation charge will be given. Glow Sign Boards are required to be installed at main entrance gate of Pump House all as directed with required supporting .2 Installation shall be done using MS Fabrication (Brackets, Flats etc.) and required PCC work (if reqd). |
| 69 | Supply and filling Gravel packing in tube well in accordance with IS: 4097, including providing gravel fine/medium/coarse, in enquired grading & sizes as per actual requirement, all complete all as specified and directed. |
| 70 | M&L for making fire fighting shed using GI pipe (light grade) 40 mm dia round / rectangular - 20 mtr, Pre- painted galvalume corrugated steel sheet 0.50mm thick of red colour approx - 5 -6 sqm including PCC foundation for fixing the supporting pole including all neccesary excavation, returning / filling wk. Rates are included all fabrication work i.e cutting, welding , nut & bolts etc.The rates are inclusive of writing \\"FIRE\\" in white paint on sheet and complete all as specified and directed. |
| 71 | M&L for fabrication, supply and installation of the Back lit Glow sign board having coloured printed with electric shock and treatment details or machinary history sheet as per following Specifications:-:(a) Box:1 The box size is approx 2 feet x 3 feet.2 The board frame should be made of MS Pipe 25x25x1.5 mm painted with one coat red oxide primer and 2 coat synthetic enamel paint.3 Top, Bottom and Side cover shall be made of 26 SWG GI sheet with powder coating and Back side of the board shall be covered with 26 SWG plain GI sheet fixed with rivet and screws.(b) Lighting/Illumination:1. Minimum one LED tube light set is to be provided per five Square feet of board area.2. Complete tube light set is to be provided. Tube lights shall be of reputed make.3. Only copper wiring will be used.(c) Flex:1. Backlit Flex should be of LG Hi-Flex.2. Writing work etc. should be digitally printed. Printing details will be provided by the department.(d) Installation:1 No separate installation charge will be given. Glow Sign Boards are required to be installed at main entrance gate of Pump House all as directed with required supporting .2 Installation shall be done using MS Fabrication (Brackets, Flats etc.) and required PCC work (if reqd). |
| 72 | Supply and laying Ductile iron (DI) pressure pipe 100 mm dia bore with socket and spygot end class K9 centrifugally cast suitable for tigthen joints with pressure technology including cement mortar lining inside the pipe as per IS 8329/2000 complete all as specified and directed by Engineer in charge |
| 73 | Taking down CI/GI tubing150 /100/80 mm mm bore of any description including cleaning for refixing or removal to store complete all as specified and directed. |
| 74 | Schedule of credit of Amount Rs. 59,999.00 to be deducted during AOC. Please Enable Macros to View BoQ information |
AI Tender Summary
Tender Timeline
Jul 15, 2026
11:30 IST
Tender Published
Tender notice published.
TodayAug 05, 2026
17:00 IST
Bid Submission Deadline
Online submission via eProcurement portal.
Upcoming · 21 daysAug 12, 2026
Bid Opening Date
Technical bids will be opened and evaluated.
Upcoming · 28 daysTender Documents
Download All (ZIP) ↓
Disclaimer
We takes all possible care for accurate & authentic tender information. However users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender