Tender For Construction Of Nuclear Medicine Block At Skims Soura(Balance Work)..
Tender Value
10.01 Crore
Estimated cost
Bid Submission
11 Aug 2026
20 days left
EMD
20.02 Lakhs
Bank guarantee accepted
Document Fee
11000
Non-refundable
Tender Type
Online
Tender Overview
Organization
Tender ID
Competition Type
NCB
Bidding Type
Tender
Location / State
Srinagar → Jammu and Kashmir
EMD Exemption
Available
Quantity
Not Available
Website
Contact Person
Address
Project Description
Tender for Construction Of Nuclear Medicine Block At Skims Soura(Balance Work)..
BOQ
| Sl. No. | Item Description |
| 1 | (A)CIVIL PART |
| 2 | Engagement of JCB/ Tippers for clearence of mulba/ debris including disposal of same to make the area workable complete in all respects. |
| 3 | Engagement of manual labours for removal of old mulba from ground floor site |
| 4 | Earth work in excavation by manual means in trenches for foundations, drains, pipes, cables etc. (not exceeding 1.5 m in width) and for shafts, wells, cesspits and the like not exceeding 10 sqm on plan, including dressing of sides and ramming of bottoms lift upto 1.5 m, including getting out excavated earth and disposal of surplus excavated earth as directed: 50 meter beyond 1 m from cutting edge. |
| 5 | Earth work in bulk excavation by mechanical means (hydraulic excavator) over areas (exceeding 30 cm in depth, 1.5 m in width as well as 10 m2 on plan) including disposal of excavated earth lead upto 50 meters and lift upto 1.5 m, as directed by Engineer-in-Charge. in all kinds of soil |
| 6 | Extra for every additional lift of 1.5 m or part thereof in excavation/banking excavated or stacked material :All kinds of soil |
| 7 | Filling available excavated earth (excluding rock) in trenchs, plinth, sides of foundation etc. Layers not exceeding 20cm in depth, consolidating each deposited layer by ramming and watering lead upto 50m and lift upto 1.5m.: |
| 8 | Supplying and laying of stone solling duely hand packed tightly including dressing, ramming and all carriages complete |
| 9 | Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work upto plinth levels in 1:4:8 (1 Cement : 4 coarse sand : 8 graded stone aggregate 40 mm nominal size). |
| 10 | Providing and laying in position specified grade of reinforced cement concrete including curing but excluding the cost of centering, shuttering, finishing and reinforcement. All works upto plinth level in 1:1½:3 (1 cement : 1½ coarse sand : 3 graded stone aggregate 20 mm nominal size) |
| 11 | Reinforced cement concrete work in walls (any thickness) including attached pilasters, buttresses, plinth and string courses, fillets, columns, pillars, piers, abutments, posts and struts upto floor five level including curing but excluding cost of centering shuttering, finishing and reinforcement in 1:1½:3 (1 cement : 1½ coarse sand : 3 graded stone aggregate 20 mm nominal size) |
| 12 | Reinforced cement concrete work in beams, suspended floors, roofs having slope upto 15°, landings, balconies, shelves, chajjas, lintels, bands, plain window sills, staircases and spiral stair cases upto five level including curing but excluding the cost of centring, shuttering, finishing and reinforcement with 1:1½:3 (1 cement : 1½ coarse sand : 3 graded stone aggregate 20 mm nominal size) |
| 13 | Steel reinforcement for RCC works including straightening, cutting, bending, binding and placing in position all complete. |
| 14 | Centering and Shuttering including strutting, propping etc and removal of form work. |
| 15 | in Foundation footings, basis of columns etc for mass concrete. |
| 16 | In walls (any thickness) including attached pilasters, butresses, plinth and string courses etc. |
| 17 | Suspended floors, roofs, landings, balconies and access platform. |
| 18 | Edges of slab and breaks in floors and walls under 20cm wide. |
| 19 | Brick masonry with FPS bricks of class designation 75 in foundation and plinth in cement mortar 1:6 (1 cement:6cement coarse sand) including all carriage complete. |
| 20 | Extra for brickwork in superstructure above plinth level upto floor V level |
| 21 | Half brick masonry with bricks of class designation 75 in super structure upto floor v level Cement mortar 1:4 (1 cement : 4 coarse sand) |
| 22 | Extra for half brick masonary in super structure above plinth level upto floor V level |
| 23 | Extra for providing and placing in position 2 no. 6mm dia M.S bars at every third course of half brick masonary |
| 24 | Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work upto plinth levels in 1:2:4 mix (1 Cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size). |
| 25 | Cement concrete flooring 1:2:4 (1cement: 2 coarse sand: 4 graded stone aggregate) finished with a floating coat of neat cement including cement slurry and curing complete, but excluding the cost of nosing of steps etc. complete.(50mm thick with 20 mm nominal size stone aggregate.) |
| 26 | Providing and laying polished Granite stone flooring in required design and patterns, in linear as well as curvilinear portions of the building all complete as per the architectural drawings with 18 mm thick stone slab over 20 mm (average) thick base of cement mortar 1:4 (1 cement : 4 coarse sand) laid and jointed with cement slurry and pointing with white cement slurry admixed with pigment of matching shade including rubbing, curing and polishing etc. all complete as specified and as directed by the Engineer-in-Charge : |
| 27 | Providing and fixing 18mm thick gang saw cut, mirror polished, premoulded and prepolished, machine cut for kitchen platforms, vanity counters, window sills, facias and similar locations, of required size, approved shade, colour and texture laid over 20 mm thick base cement mortar 1:4 (1 cement : 4 coarse sand), joints treated with white cement, mixed with matching pigment, epoxy touch ups, including rubbing, curing, moulding and polishing to edges to give high gloss finish etc. complete at all levels. Granite of any colour or shade (Area of slab upto 0.5 sqm) 18mm thick |
| 28 | Providing and fixing 18mm thick gang saw cut, mirror polished, premoulded and prepolished, machine cut for kitchen platforms, vanity counters, window sills, facias and similar locations, of required size, approved shade, colour and texture laid over 20 mm thick base cement mortar 1:4 (1 cement : 4 coarse sand), joints treated with white cement, mixed with matching pigment, epoxy touch ups, including rubbing, curing, moulding and polishing to edges to give high gloss finish etc. complete at all levels. Granite of any colour or shade (Area of slab over 0.5 sqm)) 18mm thick |
| 29 | Extra for Providing edge moulding to 18 mm/16 mm thick marble stone counters, Vanities etc. including machine polishing to edge to give high gloss finish etc. complete as per design approved by Engineer-in-Charge. Granite Work |
| 30 | Providing and laying vitrified floor tiles in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS:15622 of approved make, in all colours and shades, laid on 20mm thick cement mortar 1:4 (1cement :4 coarse sand) including grouting the joints with white cement and matching pigments etc. complete (Size of tile 600x600 mm) |
| 31 | Providing and laying Vitrified tiles in different sizes (thickness to be specified by manufacturer), with water absorption less than 0.08 % and conforming to I.S. 15622, of approved make, in all colours and shades, in walls etc , over 12 mm thick bed of cement mortar 1:3 (1 cement: 3 coarse sand), including grouting the joint with white cement and matching pigments etc. complete.(Size of tile 600x1200 mm) |
| 32 | Kota stone slab flooring 25 mm thick over 20mm (average) thick base laid over and jointed with grey cement slurry mixed with pigment to match the shade of the slab, including rubbing, polishing and curing complete with base of cement mortar 1:4 (1 cement : 4 coarse sand) : |
| 33 | Washed stone grit plaster on exterior walls of height upto 10 m above ground level in two layers, under layer 12 mm cement plaster 1:4 (1 cement : 4 coarse sand), furrowing the under layer with scratching tool, applying cement slurry on the under layer @ 2kg of cement per m2, top layer 15mm cement plaster 1:1/2 :2 (1 cement: 1/2 coarse sand : 2 stone chippings 10mm nominal size), in panels with groove all around as per approved pattern including scrubbing and washing the top layer with brushes and water to expose the stone chippings, complete as per specification and direction of Engineer-in -charge (payment for providing grooves shall be made separately). |
| 34 | Forming groove of uniform size in the top layer of washed stone grit plaster as per approved pattern using wooden battens, nailed to the under layer, including removal of wooden battens, repair to the edges of panels and finishing the groove complete as per specifications and direction of the Engineer-in-charge : 15 mm wide and 15 mm deep groove |
| 35 | Extra for washed grit plaster on exterior walls of height more than 10m ground level for every additional height of 3m or part thereof |
| 36 | Providing and fixing of 2mm thick imported vinyl flooring, 100% recycled flexible, homogeneous antistatic calendared compacted floor covering suitable for heavy traffic areas having total weight 2950 g/m2 in sheets of size 2mtrsx 20mtrs in approved pattern & colour combination with Evercare TM- patented polyurethane surface treatment with unique performance in staining providing unrivalled chemical and scratching resistance. Having wear resistance of 4.00mm3 as per EN 660.2 and wear group 'T' as per En-649 and should have a residual indentation of <0.03mm confirming to EN-433. The laid flooring should have semi- directional design, colour dyed as a raw mixture to ensure even colour throughout the thickness and its surface should be densely compacted for improvimg wear and ease of maintaniance with antibacterial and fungicidal properties. The laid flooring shall confirm the fire rating B1 class as per EN 13501-1. It shoukd have low VOC contain ac TVOC after 28 days <10g/m3 as per ISO 16000-6. The floor finsh should be terminate at the room perimeter passing over a concealed cove former and continiuing up to the wall for 100mm. The joints in the flooring should be sealed by using a PVC welding bar of matching colour to be supplied by the manufacturer, using a hot air gun for fusion of welding bar with flooring. The Vinyl sheet shall be laid & fixed with water based adshive preferably AROBOND-44 of M/s Arofine make or VC 31 of M/s Pidilite Ind. or any other make as per manufacturer's specification as per directions and entire satisfaction of Enginer-in -Charge. |
| 37 | Providing of 3mm avg thick layer of cementations salt smoothening compound of Ardex CL-II or equivalent as recominded by the Vinyl sheet flooring manufacturer over and including a priming compound of Ardex P-51 or equivalent as recomminded by Vinyl sheet flooring manufacturer on concrete surface to provide a smooth & homogenous surface for laying of Vinyl sheet flooring complete to the entire satisfaction of Engineer-in- Charge. |
| 38 | 12mm cement plaster of mix .1 : 6 ( 1 cement , 6 fine sand) all carriages complete |
| 39 | 6mm cement plaster to ceiling of mix .1 : 3 ( 1 cement , 3 fine sand) |
| 40 | Providing and applying white cement based putty of specified thickness 1mm, of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete. |
| 41 | Applying priming coats with primer of approved brand and manufacture, having low VOC (Volatile Organic Compound) content. water thinnable cement primer |
| 42 | Wall painting with premium acrylic emulsion paint of interior grade, having VOC (Volatile Organic Compound) content less than 50 grams/ liter of approved brand and manufacture, including applying additional coats wherever required to achieve even shade and colour.( two or more coats) |
| 43 | Structural steel work welded in built up sections, trusses and framed work including cutting, hoisting, fixing in position, and applying a primming coat of approved steel primer incl all carriages complete. |
| 44 | Providing and fixing stainless steel (Grade 304) railing made of Hollow tubes channels, plates etc. including welding ,grinding, buffing, polishing and making curvature (wherever required) and fitting the same with necessary stainless steel nuts and bolts complete ,including fixing the railing with necessary accessories and stainless steel dash fasteners, stainless steel bolts etc. of required size, on the top of the floor or the side of waist slab with suitable arrangement as per approval of Engineer-in-charge, (for payment purpose only weight of stainless steel members shall be considered excluding fixing accessories such as nuts, bolts, fasteners etc.). |
| 45 | Providing and fixing precoated galvanized iron profile sheets (size, shape and pitch of corrugation as approved by Engineer-in-charge) 0.50 mm (+ 0.05 %) total coated thickness with zinc coating 120 grams per sqm as per IS: 277, in 240 mpa steel grade, 5-7 microns epoxy primer on both side of the sheet and polyester top coat 15-18 microns. Sheet should have protective guard film of 25 microns minimum to avoid scratches during transportation and should be supplied in single length upto 12 metre or as desired by Engineer-in-charge. The sheet shall be fixed using self drilling /self tapping screws of size (5.5x 55 mm) with EPDM seal, complete upto any pitch in horizontal/ vertical or curved surfaces, ridges & Valleys etc excluding the cost of purlins, rafters and trusses and including cutting to size and shape wherever required. (Hi Rib Colour coated) |
| 46 | Providing and fixing ISI marked flush door shutters conforming to IS: 2202 (Part I) non-decorative type, core of block board construction with frame of 1st class hard wood and well matched commercial 3 ply veneering with vertical grains or cross bands and face veneers on both faces of shutters. 35 mm thick including ISI marked MS pressed Bright finished butt hinges with necessary screws of required size. |
| 47 | Extra for Providing lipping with 2nd class teak wood battens 25mm depth on all edges of flush door shutters( over all area of the door shutter to be measured) |
| 48 | Extra for Providing vision panel not exceeding 0.1 sqm in all types of flush doors( cost of glass excluded)( over all area of the door shutter to be measured) (Rectangular or Square). |
| 49 | Providing and fixing aluminum extruded section body tubular type universal hydraulic door closer,(having brand logo with IS: 3564, embossed on the body, door weight upto 36 kg to 80 kg and door width from 701 mm to 1000 mm), with double speed adjustment with necessary accessories and screws etc. complete : |
| 50 | Providing and fixing aluminum sliding door bolts, ISI marked anodised ( anodic coating not less than grade AC 10 as per IS:1868) transparent or dyed to required colour or shade, with nuts and screws etc comolete.( 300x16mm) |
| 51 | Providing and fixing aluminum tower bolts, ISI marked anodised ( anodic coating not less than grade AC 10 as per IS:1868) transparent or dyed to required colour or shade, with nuts and screws etc complete.( 300x16mm) |
| 52 | 300x10mm |
| 53 | 150x10mm |
| 54 | 100x10mm |
| 55 | Providing and fixing aluminum handles, ISI marked anodised ( anodic coating not less than grade AC 10 as per IS:1868) transparent or dyed to required colour or shade, with nuts and screws etc complete. |
| 56 | 125mm |
| 57 | 100mm |
| 58 | Providing and fixing 50cm long aluminum kicking plate 100x3.14mm , ISI marked anodised ( anodic coating not less than grade AC 10 as per IS:1868) transparent or dyed to required colour or shade, with nuts and screws etc complete. |
| 59 | Providing and fixing aluminum hanging floor door stopper, ISI marked anodised ( anodic coating not less than grade AC 10 as per IS:1868) transparent or dyed to required colour or shade, with nuts and screws etc complete. |
| 60 | Providing and fixing aluminum casement stays , ISI marked anodised ( anodic coating not less than grade AC 10 as per IS:1868) transparent or dyed to required colour or shade, with nuts and screws etc complete. |
| 61 | Providing and fixing decorative high pressure laminated sheet of plain/wood grain in gloss/matt/suede finish with high density protective surface layer and reverse side of adhesive bonding quality conforming to IS: 2046 Type S including cost of adhesive of approved quality. 1mm thick.. |
| 62 | Providing and fixing fiber glass reinforced plastic (FRP) door frames of cross section 90mmx45mm having single rebate of 32mmx15mm to receive shutter of 30mm thickness The laminate shall be moulded with fire resistant grade unsaturated polyester resin and chopped mat. Door frame laminates shall be 2mm thick and shall be filled with suitable wooden block in all three legs. The frame shall be covered with fiber glass from all sides. MS stay shall be provided at the bottom to steady the frame |
| 63 | Providing and fixing to existing door frames , 30mm thick Fiberglass reinforced plastic (FRP) Flush door shutter in different plain and wood finished made with fire retardant grade unsaturated polyester resin, moulded to 3mm thick FRP laminate all around with suitable wooden blocks inside at required places for fixing of fittings and polyurethane foam (PUF)/ polystyrene foam to be used as filler material throughout the hollow panel, casted monolithically with testing parameters of FRP laminate confirming to table- 3 of IS : 14856-2000, complete as per directions of engineer-in-charge. |
| 64 | Providing and fixing bright finished brass 100 mm mortice latch and lock with 6 levers and a pair of lever handles of approved quality with necessary screws etc. complete. |
| 65 | Providing and fixing aluminum work for doors, windows, ventilators and partitions with extruded built up standard tubular sections/appropriate Z sections and other sections of approved make conforming to IS: 733 and IS: 1285, fixed with dash fastener of required dia. and size including necessary filling up of gaps at junctions i.e, at top, bottom and sides with required PVC/ neoprene felt etc. Aluminum sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminum snap beading for glazing / panelling, C.P. brass / stainless steel screws, all complete as per architectural drawings and the directions of Engineer-in-Charge (glazing, panelling and dash fasteners to be paid for separately.) Powder coated aluminum (minimum thickness of powder coated 50 microns) |
| 66 | For fixed portion Powder coated aluminum (minimum thickness of powder coated 50 microns) |
| 67 | For shutters of doors, windows & ventilators including providing and fixing hinges / pivots and making provision for fixing offittings wherever required including the cost of EPDM rubber / neoprene gasket required (Fittings shall be paid for separately.)Powder coated aluminum (minimum thickness of powdercoated 50 microns) |
| 68 | Providing and fixing 12mm thick prelaminated particle board flat pressed three layer or graded wood particle board (conforming to IS: 12823 Grade-I type-II) in panelling fixed in aluminum doors, windows shutters and partition frames with C.P. brass / stainless steel screws etc. complete as per architectural drawings and directions of engineer-incharge. Pre-laminated particle board with decorative lamination on both sides. |
| 69 | Providing and fixing glazing in aluminum door, window, ventilator shutters and partitions etc. with EPDM rubber / neoprene gasket etc. complete as per the architectural drawings and the directions of engineerin- charge. (Cost of aluminum snap beading shall be paid in basic item.) With floating glass panes of 5.50 mm thickness |
| 70 | Providing and fixing G.I. pipes complete with G.I. fittings and clamps, including cutting and making good the walls etc.: |
| 71 | 15mm nominal bore |
| 72 | 20mm nominal bore |
| 73 | 25mm nominal bore |
| 74 | 40mm nominal bore |
| 75 | Providing and fixing of C.P bib cock of approved make ( Jaquar/ Parko ) Short Body |
| 76 | Providing and fixing of C.P bib cock of approved make ( Jaquar/ Parko ) Long Body |
| 77 | Providing and fixing of C.P Angle value of approved make ( Jaquar/ Parko ) |
| 78 | Providing and fixing of C.P Wall mixer of approved make ( Jaquar/ Parko ) |
| 79 | Providing and fixing of C.P basin mixer elbow action mixer of approved make ( Jaquar/ Parko ) |
| 80 | Providing and fixing Stainless Steel A ISI 304 (18/8) kitchen sink as per I.S. 13983 with C.I. brackets and stainless steel plug 40 mm, including painting of fittings and brackets, cutting and making good the walls wherever required size 610x510mm bowl depth 200mm |
| 81 | Providing and fixing of PVC connections of approved make 18\\" length |
| 82 | Providing and fixing of sink waste 100mm of approved make |
| 83 | Providing and fixing of CP health faucet of approved make ( jaquar/ Parko) |
| 84 | Providing and fixing of Mirror of Superior quality of approved make. |
| 85 | Providing and fixing of C.p soap case of approved make. |
| 86 | Providing and fixing of C.p grattings of approved make.a |
| 87 | Providing and fixing of ball valve of approved make. |
| 88 | 20mm nominal bore |
| 89 | 40mm nominal bore |
| 90 | Providing and fixing of ball valve of approved make. |
| 91 | GI union 15mm |
| 92 | GI union 20mm |
| 93 | GI union 25mm |
| 94 | GI union 40mm |
| 95 | Reducer 25x20mm |
| 96 | Reducer 20x15mm |
| 97 | Reducer 25x40mm |
| 98 | Providing and fixing white vitreous china pedestal type water closet (European type W.C. pan) with seat and lid, 10 liter low level white P.V.C. flushing cistern, including flush pipe with manually controlled device (handle lever), conforming to IS:7231, with all fittings and fixtures complete, including cutting and making good the walls and floors wherever required: |
| 99 | Providing and fixing white vitreous china flat back or wall corner type lipped front urinal basin of 430x260x350mm and 340x410x265 mm sizes respectively with automatic flushing cistern with standard flush pipe and C.P. brass spreaders with brass unions and G.I. clamps complete, including painting of fittings and brackets, cutting and making good the walls and floors wherever required: One urinal basin with 5 liter white P.V.C automatic flushing cistern. |
| 100 | Providing and fixing wash basin with C.I. brackets, 32 mm C.P. brass waste of standard pattern, including painting of fittings and brackets, cutting and making good the walls wherever required :(size 550x400mm) |
| 101 | Providing and fixing china pedestal for wash basin completely recessed at the back for the reception of pipes and fittings. |
| 102 | Providing and fixing of CP nipples of approved quality and manufacture. |
| 103 | 15x25mm |
| 104 | 15x50mm |
| 105 | Providing and fixing of toilet paper holder CP brass of approved quality and manufacture( Jaquar/ Parko/ Hindware) |
| 106 | Providing and placing on terrace (at all floor levels) polyethylene water storage tank with cover and suitable locking arrangement and making necessary holes for inlet, outlet and overflow pipes but without fittings and the base support for tank |
| 107 | Providing and fixing of glass shelves 600x120mm of approved quality and manufacture. |
| 108 | Providing and fixing of brass ball cock of approved quality and manufacture.a |
| 109 | Providing and fixing of tanky nipples of approved quality and manufacture. |
| 110 | Providing and fixing of PVC pipes of approved make C- Class ( Prince, Finolex or equivalent as approved by Engineer-in- Charge ) including rubber gasket etc.following fittings of approved brand. |
| 111 | 150mm |
| 112 | 100mm |
| 113 | Providing and fixing of PVC fittings of approved make as approved by Engineer-in- Charge ) |
| 114 | Plain bend (150mm) |
| 115 | Plain tee(150mm) |
| 116 | Floor trap(75mm) |
| 117 | Plain bend (75mm) |
| 118 | Plain bend (40mm) |
| 119 | Plain bend (100mm) |
| 120 | Door Tee (100mm) |
| 121 | Junction 75x150 |
| 122 | Junction 100x150 |
| 123 | Collar 100mm |
| 124 | Constructing brick masonry manhole in cement mortar 1:4 ( 1 cement : 4 coarse sand ) with R.C.C. top slab with 1:1.5:3 mix (1 cement : 1.5 coarse sand : 3 graded stone aggregate 20 mm nominal size), foundation concrete 1:4:8 mix (1 cement : 4 coarse sand : 8 graded stone aggregate 40 mm nominal size),inside plastering 12 mm thick with cement mortar 1:3 (1 cement : 3coarse sand) finished with floating coat of neat cement and making channels in cement concrete 1:2:4 (1 cement : 2 coarse sand : 4graded stone aggregate 20 mm nominal size) finished with a floating coat of neat cement complete as per standard design : nside size 90x80 cm and 45 cm deep including C.I. cover with frame |
| 125 | Providing and fixing of 2mm to 3mm thick lead for door shutters including cutting , fixing, all complete. |
| 126 | Providing and laying flamed finish Granite stone flooring in required design and patterns, in linear as well as curvilinear portions of the building all complete as per the architectural drawings with 18 mm thick stone slab over 20 mm (average) thick base of cement mortar 1:4 (1 cement : 4 coarse sand) laid and jointed with cement slurry and pointing with white cement slurry admixed with pigment of matching shade including rubbing, curing and polishing etc. all complete as specified and as directed by the Engineer-in-Charge Flamed finish granite stone slab Jet Black, Cherry Red, Elite Brown, Cat Eye or equivalent. |
| 127 | Fixing glazed/Ceramic/Vitrified floor tiles with cement based high polymer modified quick-set tile adhesive (water based) conforming to IS:15477, in average 3mm thickness |
| 128 | Making plinth protection 50mm thick of cement concrete 1:3:6 (1 cement : 3 coarse sand :6 graded stone aggregate 20 mm nominal size) over 75mm bed of dry brick ballast 40mm nominal size well rammed and consolidated and grouted with fine sand including finishing the top smooth and curing complete |
| 129 | Carriages of materials by mechnical transport. |
| 130 | Sand from 12Km |
| 131 | Aggregate from 20 Km |
| 132 | Bricks from 26 km |
| 133 | (B)MECHANICAL PART (S.I.T.C of various mechanical components of new Nuclear Medicine block including MGPS, HVAC ,Fire Fighting and Lift at SKIMS, Soura) |
| 134 | 1.MGPS facility to Nuclear medicine Block in SKIMS, Soura. |
| 135 | Providing, installation, testing and commissioning of 4 feet 6 port bed head service console consisting of PB (Puritan Bennett) type two No. oxygen ports, two No. suction ports, one No. compressed air port and one nitrous oxide port along with two No. electric socket, IV hook and SS basket. The unit shall have smooth curved surfaces with no visible screws. Removal of the covers for maintenance and pipeline connection shall be easy. The unit shall be manufactured in accordance with international and European standards ISO 11197 and EN 793.Material: High-grade aluminium alloy, Finish: Powder-coated with antibacterial properties.Standards: All gas outlets comply with NFPA-99 standard.Safety and compliance certification: CE marked compliance with IEC 60601-1 (Medical Electrical Equipment) and IEC 60601-2 (Particular requirements for the basic safety and essential performance of hospital equipment).Installation and maintenance: Installation: Concealed fixings and installation performed by certified technicians. Job includes installation charges.Maintenance: Easy access panels for maintenance and repair, regular maintenance checks as per manufactures guidelines. |
| 136 | Providing, installation, testing and commissioning of 4 feet 5 port bed head service console consisting of PB (Puritan Bennett) type two No. oxygen ports, two No. suction ports and one No. compressed air port along with two No. electric socket, IV hook and SS basket. The unit shall have smooth curved surfaces with no visible screws. Removal of the covers for maintenance and pipeline connection shall be easy. The unit shall be manufactured in accordance with international and European standards ISO 11197 and EN 793.Material: High-grade aluminium alloy, Finish: Powder-coated with antibacterial properties.Standards: All gas outlets comply with ISO 7391-1 standard.Safety and compliance certification: CE marked compliance with IEC 60601-1 (Medical Electrical Equipment) and IEC 60601-2 (Particular requirements for the basic safety and essential performance of hospital equipment).Installation and maintenance: Installation: Concealed fixings and installation performed by certified technicians. Job includes installation charges.Maintenance: Easy access panels for maintenance and repair, regular maintenance checks as per manufactures guidelines. |
| 137 | Providing, installation, testing and commissioning of 3 feet 4 port bed head service console consisting of PB (Puritan Bennett) type two No. oxygen ports, two No. suction ports along with two No. electric socket, IV hook and SS basket. The unit shall have smooth curved surfaces with no visible screws. Removal of the covers for maintenance and pipeline connection shall be easy. The unit shall be manufactured in accordance with international and European standards ISO 11197 and EN 793.Material: High-grade aluminium alloy, Finish: Powder-coated with antibacterial properties.Standards: All gas outlets comply with ISO 7391-1 standard.Safety and compliance certification: CE marked compliance with IEC 60601-1 (Medical Electrical Equipment) and IEC 60601-2 (Particular requirements for the basic safety and essential performance of hospital equipment).Installation and maintenance: Installation: Concealed fixings and installation performed by certified technicians. Job includes installation charges.Maintenance: Easy access panels for maintenance and repair, regular maintenance checks as per manufactures guidelines. |
| 138 | Providing and fitting of following dia and thickness medical gas copper pipe line, as per ASTM B8 19/IS 2501/BS 2874 including all standard procedures for laying jointing cutting, brazing polishing and providing of all necessary copper fittings (bends, tees etc) exposed manner alongside concrete/wooden walls/ceiling by way of providing and fixing of plastic saddles of required size at suitable distance. The pipe line route shall be as per site requirements or as instructed by site engineer. |
| 139 | 10 mm seamless tubing 0.9 mm thickness |
| 140 | 15 mm seamless tubing 0.9 mm thickness |
| 141 | 22 mm seamless tubing 0.9 mm thickness |
| 142 | 28 mm seamless tubing 0.9 mm thickness |
| 143 | 35 mm seamless tubing 1.2 mm thickness |
| 144 | Colour coating of Medical gas copper pipe lines (Double coat) with approved shades of following sizes. |
| 145 | 10 mm seamless tubing 0.9 mm thickness |
| 146 | 15 mm seamless tubing 0.9 mm thickness |
| 147 | 22 mm seamless tubing 0.9 mm thickness |
| 148 | 28 mm seamless tubing 0.9 mm thickness |
| 149 | 35 mm seamless tubing 1.2 mm thickness |
| 150 | Providing and fixing of line isolation ball valve bronze body with brass fittings for medical gas copper pipe line confirming to IS code 9890. |
| 151 | 32 mm |
| 152 | 25 mm |
| 153 | 20 mm |
| 154 | 15 mm |
| 155 | 10 mm |
| 156 | Providing, fitting, testing and commissioning of complete strainer assembly in suction line comprising of: 15 mm bronze ball valve along with fittings- 3 No. ;15 mm Bronze/Brass strainer- 1 No. |
| 157 | Providing, fitting, testing and commissioning of complete strainer assembly in suction line comprising of: 22 mm bronze ball valve along with fittings- 3 No. ;22 mm Bronze/Brass strainer- 1 No. |
| 158 | Providing and fitting of zonal valve box four gas system. The system should be designed to provide safe and reliable isolation for emergency shutoff, maintenance and future expansion. The valves are full bore, medical-grade ball valves with quarter-turn (90ͦ) operation, ensuring smooth and quick isolation during emergencies. The valve box is housed in a robust metallic enclosure (SS/Aluminum) with a transparent acrylic viewing window, allowing clear visibility of line identification and pressure status. The window should be breakable in emergency conditions for immediate access. The valve box should have proper locking mechanism. The stub ends are designed with 15 mm diameter (Oxygen line), 22 mm diameter (Vacuum line) 15 mm diameter (Compressed air line) and 15 mm diameter (Nitrous oxide line) with 75mm length on each side facilitating easy and secure connection with medical copper pipelines. The job will include cost of ball isolation valves (bronze) and pressure gauges for each line (Both positive and negative for respective lines). The offered zonal box should comply with internationally recognized standards including ISO 7396-1:2016/BS EN 331:2025, medical devices Directive 93/42/EEC, and pressure equipment Directive 97/23/EC. |
| 159 | Providing, fitting and testing of BPC flow meter with humidifier bottles & BPC adapter connected to self-sealing valves of oxygen (0-15 LPM) |
| 160 | Providing fixing of ward vacuum unit with regulator, collection jar of 1000ml and bracket for installation of jar on bed head service console. |
| 161 | Providing and fitting of compatible oxygen probes for self sealing valves (Compatible with PB type ports). |
| 162 | Providing and fitting of compatible vacuum probes for self sealing valves (Compatible with PB type ports). |
| 163 | Providing and fitting of compatible medical air probes for self sealing valves(Compatible with PB type ports). |
| 164 | Providing and fitting of compatible Nitrous oxide probes for self sealing valves (Compatible with PB type ports). |
| 165 | Providing, fitting of high-pressure soft tubing for suction. |
| 166 | Providing, installation, testing and commissioning of 4 gas digital medical gas alarm system with hooter designed to continuously monitor pipeline pressure for gases oxygen, vacuum, medical air and nitrous oxide. It should have intuitive LCD screen or LED panel to show real time gas pressure. The system should come with color-coded visual indicators (Green for normal, Red/Yellow for errors) and in case of high pressure and low pressure it generates appropriate alarm. |
| 167 | Providing, fitting of dial type pressure gauges at various places in medical air pipeline with range 0-10 bar confirming to relevant ISO code. The job includes providing and fitting of all accessories required for making pressure gauges functional. |
| 168 | 4’’ dial |
| 169 | 2\\" dial |
| 170 | Providing and fitting of 22 mm pressure regulating valve on medical air line |
| 171 | Providing, installation, testing and commissioning of the Medical air system along with allied items. The system shall have following but not limited to these.i. Oil free air compressors (in duplex i.e 02 Nos) two stage of not less than 24.5 cfm capacity along with 7.5 HP 3 phase 440 volt electrical motor and base frame. The job includes lying of 2 No. foundation blocks in RCC (1:2:4 ratio) 125mm x 65mm x 50mm and then fixing the foundation bolts assorted size as per the slots provided in the base frame of machine. The job includes all material, labour and curing charges.ii. The air compressors should be controlled by fully automatic digital duplex cascading control panel to be designed by OEM as per site requirement. The panel should be PLC/Microprocessor based to provide precise digital switching between compressors. The panel should have following features:• Alternates the lead and lag roles, ensuring one compressor doesn’t fail prematurely.• If pressure drops below the threshold while the first compressor is running, the panel automatically starts the second compressor to meet the heavy demand. • If the primary compressor breaks down, the panel automatically switches control to the standby compressor so your facility experience zero downtime. • Built in safeguards against over/under voltage, current overload and phase reversal.• Manual/Auto mode for direct manual control of the compressors if the electronic circuit trips or requires servicing. i. Air compressor shall be provided with MS air tank of 500 ltrs. Capacity cylinderical tank with dish end as per IS 2062, working pressure 10Kg/cm². The air receiver should be provided with no air loss type automatic drain along with manual drain facility and accessories like pressure gauge, pressure limit switch and safety valve etc. Job involves colour coating of air tank first by primer and then two coat black paint.ii. On leaving the air receiver tank, the air shall pass through chain of a duplex pre-filter and twin column dryer assembly, each chain shall be capable of passing the full flow of air compressor. Duplex Desiccant air dryer (Modular type) system shall be provided with 1st charge of molecular sieves (desiccant), the sequence controller of digital type pass lines etc. Re-activation shall be on a time cycle using a bleed of purge automatic drain. The dew point of the dry air shall be minus 40 deg ‘C’iii. Four stage medical air filters comprising of bacteria filter with SS304 compliers with HTM 2022/HTM 02-01/hfpa 99/DIN standards. |
| 172 | Providing, installation, testing and commissioning of vacuum (Suction) system along with allied items. The system shall have following but not limited to these:1): Two cylinder vacuum pumps (In duplex i.e 2 Nos) of not less than 111 cfm capacity and vacuum pressure of 29.2 in Hg (Sea level) along with 7.5 HP 3 phase 440 volt electrical motor, moisture separator, exhaust muffler, vacuum filter and confirming to IS code 6849-1, 6849-2. The job includes any other accessory provided as a standard by the OEM for safe operation of the machine. The job includes lying of 2 No. foundation blocks in RCC (1:2:4 ratio) 125mm x 65mm x 50mm and then fixing the foundation bolts of assorted size as per the slots provided in the base frame of machine. The job includes all material, labour and curing charges.2): The Vacuum pumps should be controlled by fully automatic digital duplex cascading control panel to be desined by OEM as per site requirement. The panel should be PLC/Microprocessor based to provide precise digital switching between vacuum pumps. The panel should have following features:• Alternates the lead and lag roles, ensuring one vacuum pump doesn’t fail prematurely.• If pressure drops below the threshold while the first vacuum pump is running, the panel automatically starts the second vacuum pump to meet the heavy demand.• If the primary vacuum pump breaks down, the panel automatically switches control to the standby vacuum pump so your facility experience zero downtime.• Built in safeguards against over/under voltage, current overload and phase reversal.• Manual/Auto mode for direct manual control of the vacuum pumps if the electronic circuit trips or requires servicing. 3): The vacuum system shall be provided with MS tank of 1000 ltrs. Capacity cylinderical type with dish end as per IS 2062, working pressure -40 in of hg. The suction tank should be provided with strainer type ball valve on suction line from system to tank of appropriate diameter and drain valve at the base of tank along with accessories like vacuum pressure gauge, vacuum limit switch and non return valve etc. Job involves colour coating of air tank first by primer and then two coat yellow paint. |
| 173 | Providing and fitting of 50 mm NB C class MS piping confirming to IS code 1239 connecting from vacuum pumps to vacuum tank including all standard procedures for laying jointing cutting, welding, polishing and providing of all necessary fittings , bends, tees etc. The job includes color coating of approved shade. |
| 174 | Providing, installation, testing and commissioning of 12x12 new oxygen battery bank complete with lead (High pressure pipes), interconnecting copper pipes, 24 No. copper tail pipes with NRV for cylinders, mounting angle iron 50x50x5 mm to be fixed on the wall with clamps/dash fasteners to hold the 12x12 cylinder system in place. The job includes providing/fitting of new fully automatic analog oxygen panel. The control panel should be capable of regulating minimum 1500 LPM oxygen flow for twin bank (12+12) with auto regulation and shall be designed with standing the oxygen cylinder pressure in the range of 0-200 kgf/cm2 with safety features related to hazard and continuity of flow of medical grade oxygen. The panel shall operate at a constant pressure upto 6 bar through two banks of bottled gas cylinders with following status and indication system.a): Bank in use- Green indication.b): Bank ready for use- Yellow indication.c): Empty bank- Red indication. The control panel shall have built in display to indicate normal, high and low line pressure. The control panel shall incorporate safety provision in case of failure of electronic as well as pneumatic system. Control shall be able to be used manually through by pass system. Job includes all brazing charges, wiring, thimbling, piping, valves required for successful installation testing and commissioning of the battery bank. The equipment shall conform to the relevant ISO/BIS standard and the firm shall have to submit relevant test certificates. |
| 175 | Providing, installation, testing and commissioning of 06x06 new oxygen battery bank complete with lead (High pressure pipes), interconnecting copper pipes, 12 No. copper tail pipes with NRV for cylinders, mounting angle iron 50x50x5 mm to be fixed on the wall with clamps/dash fasteners to hold the 06x06 cylinder system in place. The job includes providing/fitting new fully automatic analog oxygen panel. The control panel should be capable of regulating minimum 1500 LPM oxygen flow for twin bank (06+06) with auto regulation and shall be designed with standing the oxygen cylinder pressure in the range of 0-200 kgf/cm2 with safety features related to hazard and continuity of flow of medical grade oxygen. The panel shall operate at a constant pressure upto 6 bar through two banks of bottled gas cylinders with following status and indication system.a): Bank in use- Green indication.b): Bank ready for use- Yellow indication.c): Empty bank- Red indication. The control panel should have built in LED display to indicate normal, high and low line pressure. The control panel shall incorporate safety provision in case of failure of electronic as well as pneumatic system. Control should be able to be used manually through by pass system. Job includes all brazing charges, wiring, thimbling, piping, valves required for successful installation testing and commissioning of the battery bank. The equipment shall conform to the relevant ISO/BIS standard and the firm shall have to submit relevant test certificates. |
| 176 | Providing, installation, testing and commissioning of 02x02 new nitrous oxide battery bank complete with lead (High pressure pipes), interconnecting copper pipes, 04 No. copper tail pipes with NRV for cylinders, mounting angle iron 50x50x5 mm to be fixed on the wall with clamps/dash fasteners to hold the 02x02 cylinder system in place. The job includes providing/fitting new fully automatic analog nitrous oxide panel. The control panel should be capable of regulating minimum 1500 LPM gas flow for twin bank (02+02) with auto regulation and shall be designed with standing the nitrous cylinder pressure in the range of 0-100 kgf/cm2 with safety features related to hazard and continuity of flow of gas. The panel shall operate at a constant pressure upto 6 bar through two banks of bottled gas cylinders with following status and indication system.a): Bank in use- Green indication.b): Bank ready for use- Yellow indication.c): Empty bank- Red indication. The control panel should have built in display to indicate normal, high and low line pressure. The control panel shall incorporate safety provision in case of failure of electronic as well as pneumatic system. Control should be able to be used manually through by pass system. Job includes all brazing charges, wiring, thimbling, piping, valves required for successful installation testing and commissioning of the battery bank. The equipment shall conform to the relevant ISO/BIS standard and the firm shall have to submit relevant test certificates. |
| 177 | Construction of PUF shed of size 25’ x 20’ x 15’ along with allied Components |
| 178 | Clearing of site for MGPS shed from debris, soil, cutting of bushes etc by way of using Mechanical/manual measures and disposal of material as directed by site engineer. |
| 179 | Earth work in Bulk excavation by manual means over areas (exceeding 30 cm in depth ,1.5 m in width as well as 10 m2 in on plan) including disposal of excavated earth lead upto 50 m and lift upto 1.5 m, as directed by Engineer in Charge. |
| 180 | Supply ,filling, spreading and levelling soling stone for foundation of GI PUF shed with all leads and lifts complete. |
| 181 | Providing and laying in position specified grade of RCC including curing but excluding the cost of centering, shuttering, finishing and reinforcement .All works upto plinth level 1:1/2:3 (1 cement :1 ½ coarse sand : 3 graded stone aggregate 20 mm nominal size) |
| 182 | Providing/laying of Shuttering/cantering including propping, strutting etc. |
| 183 | Providing/laying of 6mm thick cement plaster of 1:4 mix including carriage, all leads and lifts. |
| 184 | Steel reinforcement for RCC work including straightening, cutting, bending ,placing in position and binding all complete upto plinth level thermos-mechanically treated bars of grade Fe-500D or more. |
| 185 | Fabrication of MS framed structure for PUF paneling having structural steel as per site requirement and approved drawings. |
| 186 | PUF Enclosure (Walls, Ceiling and ridges): It shall be made up of 60 mm thick rigid PUF, CFC free with profile surface on one side, conforming to IS-12436-88 with subsequent amendments having density of 40±2 kg/m3 sandwiched between 0.5 mm pre-painted Galvanized steel sheet as per IS-14246-95 with subsequent amendments with 18-20 microns of Exterior Polyester Coating of white color on epoxy primer on both sides. The basic substrate shall be Gr-120 Hot dip Galvanized steel. The panels shall be made by continuous line and shall be joined together by means of Tongue-n-groove joint system. The joints shall be air-tight by using proper sealant (like silicon PU foam etc). The PUF panels shall have closed cell content of 90-95%; Thermal Conductivity of 0.023 at 10W/mK; Compressive strength of 2.1 Kg/m2 9 (at 10% deformation); Water vapor permeability 0.08-0.12 gm/h_m2; Self-extinguishing fire property.Make : Reputed Make. |
| 187 | Providing and fitting of Eaves boarding (12 inch) to be installed on the underside of roof overhang. The job includes all tools and tackles required for successful completion of the job. |
| 188 | Providing and fitting Color coated CGI Roofing (24SWG gauge). The job includes all tools and tackles required for successful completion of the job. |
| 189 | Providing and fitting of Ridge roof sheet/Ridge cap to be installed at the topmost apex where two sloping roof sections meet. The job includes all tools and tackles required for successful completion of the job. |
| 190 | Providing/Fabrication/Fitting of Aluminum framed doors and windows of following dimensions:Door: 1nox4’x6’Window: 04nox 4’x5’Sliding door (Puff panel ) : 1no x 10’x 12’The job includes the cost of glasses and aluminum sheets fitted within the doors and windows as per site requirement. The job also includes P/F of hinges, locks and other necessary fitments required for the job. |
| 191 | P/F of Anchorage mechanism made up of MS plates of following thickness required for anchorage of vertical posts, Horizontals, truss works, flooring complete. The jobs includes cutting/welding works to be carried out as per site requirement. |
| 192 | Painting of whole MS Frame with two coats of red oxide and two coats of enamel paint after surface cleaning by using proper grade of emery paper. |
| 193 | Providing, Installation, testing and commissioning of 02 No. inline exhaust fans of following specifications • Capacity: 5900 CFM;• Fan size: As per OEM;• Fan type: Axial • Impeller type: As per OEM• Static Pressure: 20-35 mm wg;• Casing Mild steel: 2mm;• Impeller: Die cast impeller;• Bird Screen: One side MS;• No. of blades: As per OEM• Motor capacity: As per OEM;• RPM = 950; |
| 194 | Providing and fitting of PVC insulated unarmored copper conductor cable from main panel board to various equipment’s through walls/ceiling with appropriate clamps and fixing arrangement, cable tray etc. as per specifications. The job shall include providing and fitting of cable trays inside plant room of suitable size. |
| 195 | 35 mm2 4 Core |
| 196 | 16 mm2 4 Core |
| 197 | 04 mm2 3 Core |
| 198 | 2.5 mm2 3 Core |
| 199 | 1.5 mm2 2 core |
| 200 | Providing and fitting of MS perforated cable tray along with accessories having width not less than 250mm; height not less than 65 mm and thickness not less than 1.6 mm for medical gas pipes and electric cables. The tray should come with hot dip galvanized/powder coated finish. Job includes all tools and tackles (welding etc) required for successful fitting and testing commissioning of the work. |
| 201 | Providing and fitting of 3 pin electric sockets with cover of reputed make. Job includes all tools and tackles required for successful fitting and testing commissioning of the work. |
| 202 | Providing and fitting of electric switch board with 2 No. 3 pin electric sockets and 8 No. switches. Job includes all tools and tackles required for successful fitting and testing commissioning of the work. |
| 203 | Earthing for vacuum pumps, medical air compressors, LT control Panel and other electrical equipments by way of chemical earthing as per IS 4043. The job includes providing and laying of copper strip of size 25 mm x 5 mm from earthing electrode to the vacuum pumps, medical air compressors, LT control Panel and other electrical equipment’s. |
| 204 | SITC of powder coated, vermin proof Main Electric Panel fabricated out of 14 SWG CRCA sheet laid over MS angle frame, internally wired, with modular construction having incoming and outgoing MCCBs, cable way module, metering module, copper bus bars with all protections.The panel shall be equipped with the following items, integrated together for operation and control of the electro mechanical machinery. All internal wiring used shall be of the rating suitable for the individual component of the panel.Fabrication, Providing and fitting of Modular control panel of appropriate size fabricated out of 14 SWG sheet having required openings / vents and protection Class : 1P55 & fitted with accessories as under:- |
| 205 | A): Distribution buses: Electric grade copper of adequate section with red, blue and yellow colored heat shrinkable sleeves. The bus bar shall be qualifying IP 55.Requirements: Rating = 200 A Qty. = 4 No’s. No of bus bars = 4 Nos. (3 phase and 1 No neutral) Material of bus bar = Copper B): Circuit Breakers: MCCB. (Incoming) Qty. = 02 No. Rating = 200 Amp. 04 Pole, 36 KA Voltage = 415 ± 15% Frequency = 50 ± 3 % HzMCCB. (Outgoing) Qty. = 03 No. (2W+1)Rating = 100 Amp. 04 Pole, 25 KAVoltage = 415 ± 15% Frequency = 50 ± 3 % HzMCCB. (Outgoing) AuxillaryQty. = 01 No.Rating = 63 Amp. 04 Pole, 25 KAVoltage = 415 ± 15% Frequency = 50 ± 3 % HzMCCB. (Outgoing) Qty. = 02 No. Rating = 32 Amp. 04 Pole, 10 KA Voltage = 415 ± 15% Frequency = 50 ± 3 % HMCB. Double pole (Outgoing) Qty. = 10 No. Rating = 10 Amp. Double Pole, 10 KA Voltage = 415 ± 15% Frequency = 50 ± 3 % H |
| 206 | C): Motor Starters:=> Supply, laying, testing & commissioning of 4 No. DOL starter Starters for 7.5 HP Motor in sheet metal enclosure, Type = DOL starter with contactor assembly and Single Phase Preventer Motor rating = 7.5 HP AC-3 ph., 415 + 15% V, 50 + 3% Hz Relay Range = 8-12A Quantity = 02 No’sThe job includes providing & fixing copper wire as per site requirement for making input & output connections. The job is inclusive of P/F of the copper thimbles to the wire ends duly crimped with the crimping tools. =>Supply, laying, testing & commissioning of 3 No. DOL starter Starters for 2 HP Motor in sheet metal enclosure, Type = DOL starter with contactor assembly and Single Phase Preventer Motor rating = 2 HP AC-3 ph., 415 + 15% V, 50 + 3% HzRelay Range = 4-6AQuantity = 02 No’sThe job includes providing & fixing copper wire as per site requirement for making input & output connections. The job is inclusive of P/F of the copper thimbles to the wire ends duly crimped with the crimping tools. D): Ampere Meter:-Size = 96 mm Sq. Range = 0 – 100 A CT Coils = Requisite 5 VA – 10 VA capacity & CT ratio.CT coils per meter = 03 No’s Type = Digital Qty. = 03 No’s.E): Voltmeter:- Size = 96mm Sq. Range = 0-500 volts Type = Digital Qty. = 01 No. |
| 207 | Providing and fitting of 50 watt LED flood lights with IP rating IP66. Job includes all tools and tackles required for successful fitting and testing commissioning of flood lights. |
| 208 | Providing and fitting of 22 watt LED conceal lights with cut out of 188 mm and cool day light color. Job includes all tools and tackles required for successful fitting and testing commissioning of lights. |
| 209 | Providing and fitting of 1200 mm (approx.) single phase 230 V ,50 Hz high speed ceiling fan with copper motor. The fan shall have a robust motor with speed range of 350 rpm to 380 rpm and minimum air delivery of 210 m3/hr ensuring powerful air flow in all directions. |
| 210 | 2.HVAC system to Nuclear medicine Block -Phase III in SKIMS, Soura. Please Enable Macros to View BoQ information |
| 211 | 2.HVAC system to Nuclear medicine Block -Phase III in SKIMS, Soura. Please Enable Macros to View BoQ information |
AI Tender Summary
Tender Timeline
Jul 15, 2026
11:30 IST
Tender Published
Tender notice published.
CompletedAug 11, 2026
17:00 IST
Bid Submission Deadline
Online submission via eProcurement portal.
Upcoming · 20 daysAug 12, 2026
Bid Opening Date
Technical bids will be opened and evaluated.
Upcoming · 21 daysTender Documents
Download All (ZIP) ↓
Disclaimer
We takes all possible care for accurate & authentic tender information. However users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender