Tender For Under District Prayagraj, Construction Work Of Auditorium In Vikas Handiya C Us Of Prayagraj District, Lot No 1
Tender Value
88.09 Lakhs
Estimated cost
Bid Submission
27 Jul 2026
11 days left
EMD
1.77 Lakhs
Bank guarantee accepted
Document Fee
3000
Non-refundable
Tender Type
Online
Tender Overview
Organization
Tender ID
Competition Type
NCB
Bidding Type
Tender
Location / State
Pratapgarh → Uttar Pradesh
EMD Exemption
Not Available
Quantity
Not Available
Website
Contact Person
Address
Project Description
Tender for Under District Prayagraj, Construction Work Of Auditorium In Vikas Handiya C Us Of Prayagraj District, Lot No 1
BOQ
| Sl. No. | Item Description |
| 1 | Clearing jungle including uprooting of rank vegetation, grass, brush wood, trees and saplings of girth up to 30 cm measured at a height of 1m above ground level and removal of rubbish up to a distance of 50 m outside the periphery of the area cleared.as per DSR 2.31 |
| 2 | Earth work in excavation by mechanical means (Hydraulic excavator) / manual means in foundation trenches or drains (not exceeding 1.5 m in width or 10 sqm on plan), including dressing of sides and ramming of bottoms, for all lift, including getting out th |
| 3 | Supplying and filling in plinth with sand under floors, including watering, ramming, consolidating and dressing complete.as per DSR 2.27 |
| 4 | Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level : 1:4:8 (1 Cement : 4 fine sand derived from natural sources : 8 graded stone aggregate 40 mm nominal size der |
| 5 | Providing and laying in position ready mixed or site batched design mix cement concrete for reinforced cement concrete work; using coarse aggregate and fine aggregate derived from natural sources, Portland Pozzolana / Ordinary Portland /Portland Slag cement, admixtures in recommended proportions as per IS: 9103 to accelerate / retard setting of concrete, to improve durability and workability without impairing strength; including pumping of concrete to site of laying, curing, carriage for all leads; but excluding the cost of centering, shuttering, finishing and reinforcement as per direction of the engineer-in-charge, for the following grades of concrete.: Note: Extra cement up to 10% of the minimum specified cement content in design mix shall be payable separately. In case the cement content in design mix is more than 110% of the specified minimum cement content, the contractor shall have discretion to either re-design the mix or bear the cost of extra cement. Concrete of M25 grade with minimum cement content of 330 kg /cum Upto Plinth Level As Code No-5.33.1.1 |
| 6 | Centering and shuttering including stutting, propping etc. and removal of form for Foundations, footings, bases of columns etc. for mass concrete. As per DSR Code No- 5.9.1 |
| 7 | Centering and shuttering including stutting, propping etc. and removal of form for Columns, pillars, piers, abutments, posts and struts. As per DSR Code No- 5.9.6 |
| 8 | Brick work with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in foundation and plinth in Cement mortar 1:6 (1 cement : 6 coarse sand). As per DSR Code No- 6.1.2 |
| 9 | Centering and shuttering including stutting, propping etc. and removal of form for Lentels beams, plinth beams, girders, bressumers and cantilevers, As per DSR Code No- 5.9.5 |
| 10 | Providing and laying in position ready mixed or site batched design mix cement concrete for reinforced cement concrete work; using coarse aggregate and fine aggregate derived from natural sources, Portland Pozzolana / Ordinary Portland /Portland Slag cement, admixtures in recommended proportions as per IS: 9103 to accelerate / retard setting of concrete, to improve durability and workability without impairing strength; including pumping of concrete to site of laying, curing, carriage for all leads; but excluding the cost of centering, shuttering, finishing and reinforcement as per direction of the engineer-in-charge, for the following grades of concrete.: Note: Extra cement up to 10% of the minimum specified cement content in design mix shall be payable separately. In case the cement content in design mix is more than 110% of the specified minimum cement content, the contractor shall have discretion to either re-design the mix or bear the cost of extra cement. Concrete of M25 grade with minimum cement content of 330 kg /cum Above Plinth Level upto floor V level As Code No-5.33.2.1 |
| 11 | Add for using extra cement in the items of design mix over and above the specified cement content therein As per DSR Code No- 5.35 |
| 12 | Centering and shuttering including stutting, propping etc. and removal of form for Suspended floors, roofs, landings, balconies and access plateform. As per DSR Code No- 5.9.3 |
| 13 | Steel reinforcement for R.C.C. work ready to use \\"cut and bend\\" rebars of approved make from factory/workshop to construction site including placing in position and binding all complete in Thermo-Mechanically Treated bars of grade Fe-500D or more. As per Code No.- 5.22 .6 |
| 14 | Brick work with common burnt clay F.P.S. (non modular) bricks of Class designation 7.5 in super structure above plinth level upto floor V level in all shapes and sizes in cement mortar 1:6 ( 1 cement : 6 coarse sand ). As per Code No 6.4.2 |
| 15 | Half brick masonry with common burnt clay F.P.S. (non modular) bricks of Class designation 7.5 in super structure above plinth level upto floor V level. cement mortar 1:4 (1 cement : 4 coarse sand ). As per Code No 6.13.2 |
| 16 | 12mm cement plaster in single coat on fair side of single or half brick wall for interior plastering upto floor two level including brick wall for interior plastering upto floor two level including internal rounded angles chafers,and or rounded angles not excedding 80mm in grith and finished even and smooth No.extra for mixing and additive.1-1Cement:6 Sand as per DSR 13.1.2 |
| 17 | 12mm cement plaster in single coat on fair side of single or half brick wall for interior plastering upto floor two level including brick wall for interior plastering upto floor two level including internal rounded angles chafers,and or rounded angles not excedding 80mm in grith and finished even and smooth No.extra for mixing and additive.1-1Cement:6 Sand as per DSR 13.1.2 |
| 18 | E/w in filling or in embankment in foundation or plinth in ordinary soil including lift up to 1.5m and lead up to 30m and including filling watering ramming of excavated earth as per dsr 2.25a |
| 19 | Providing and applying white cement based putty of average thickness 1 mm of approved brand and manufacturer,over the plasterd wall surface even and smooth surface. As per Code No-13.80 |
| 20 | Finishing with deluxe multi surface paint system for interiors and exteriors using primer as per manufacturers specifications two or more coats applied on wall @ 1.25ltr/10sqm over and i/c one coat of special primer applied @ .90litre/10sqm as per DSR 13. |
| 21 | Providing & laying rectified glazed ceramic floor tiles of size 300x300 mm or more ( thickness to be specified by the manufacturer), of 1st quality confirming to IS:15622, of approved make, in colours white, ivory, grey, fume red brown, laid on 20 mm thick cement mortar 1:4 ( 1 cement: 4 coarse sand), jointing with grey cement slurry @ 3.3 kg/sqm including grounting the joints with white cement and matching pigmrnts etc., complete. As per Code No-11.39 |
| 22 | Providing and fixing Ist quality ceramic glazed wall tiles conforming to IS: 15622 (thickness to be specified by the manufacturer), of approved make, in all colours, shades except burgundy, bottle green, black of any size as approved by Engineer-in-Charge, in skirting, risers of steps and dados, over 12 mm thick bed of cement mortar 1:3 (1 cement : 3 coarse sand) and jointing with grey cement slurry @ 3.3kg per sqm, including pointing in white cement mixed with pigment of matching shade complete. As per DSR Code No.8.31 |
| 23 | Providing and laying vitrified floor tiles in different sizes (thickness to be .specified by the manufacturer) with water absorption less than 0.08% and conforming to IS: 15622, of approved make, in all colours and shades, laid on 20 mm thick cement mortar 1:4 (1 cement : 4 coarse sand), jointing with grey cement slurry @ 3.3 kg/ sqm including grouting the joints with white cement and matching pigments etc., complete.as per DSR 11.41.2 600mmx600mm size |
| 24 | Providing & laying polished Granite stone flooring in required design and patterns in linear as well as curvillinear portions of the building all complete as per the architectural drawing with 18mm thick in salb/rises of steps,skirting,dado & pillers laid on 20mm thick base of cement 1:4 laid and jointed with cement slurry mixed with pigment to match the shade of slabs including rubbing and polishing completed.as per DSR 8.2.2.2 |
| 25 | Making drip course in sun shade or FACIA as per direction of engineer in charge including supply of all materials labour etc.for proper completion of the work.as per DSR 5.30 |
| 26 | Providing and fixing ISI marked flush door shutter to IS-2202 (part 1) decorative type ,core of block board construction with frame of 1st class hard wood and well matched teak 3 ply veneering with vertical grain or cross band and face vennrs on both faces of shutters.Both side laminated 35mm thick including ISI marked stainless steel butt hinges with necessary screws as per DSR 9.20.1 |
| 27 | Providing wood work in frames of doors,windows,clerestory window sand other frames,wrought framed and fixed in position with hold fast lugs or with dash fasteners of required dia & length ( hold fast lugs or dash fastener shall be paid for separately) Second class sal wood as per DSR 9.1.2 |
| 28 | French spirit polishing (two or more coats on new works including a coat of wood filler as per DSR 13.68.1 |
| 29 | Providing stainless steel made sliding bolts 16mm dia with nuts and screw 250 mm long as per DSR 9.96.1 |
| 30 | Providing stainless steel made tower bolts dia with nuts and screw 150 mm long as per DSR 9.97.1 |
| 31 | Providing and fixing fly proof galvanized MS wire gauge to windows and clerestory windows using wire gauge with average width of aperture 1.40 mm in both directions with wire of dia 0.63 mm all complete .as per DSR 9.51.2 with 12mm mild steel U beading |
| 32 | Providing & fixing glass panes with putty and glazing clips in steel doors,windows, clerestory windows, all complete with :4.0 mm thick glass panes As per DSR Code 10.30.1 |
| 33 | Providing and fixing factory made uPVC glazed/wire mesh windows/ doors comprising of lead free uPVC multi-chambered frame, sash and mullion/coupler (where ever required) extruded profiles having minimum wall thickness of 1.70 mm for Series R1 and R2 profiles and 2.10 mm for Series R3 and R4 profiles conforming to EN: 12608 in any shape, colour and design duly reinforced with galvanized mild steel section made of required shape & size as per CPWD Specification, uPVC extruded glazing beads, interlocks and Inline sash adaptor (where ever required) of appropriate dimension, EPDM gasket, hardware, SS 304 grade fasteners of minimum 8 mm dia with countersunk head, comprising of matching polyamide PA6 grade sleeve for fixing frame to finished wall as per IS 1367 : Part 1 to 14, plastic packers, plastic caps and necessary stainless steel screws etc. Profile of frame, sash & mullion (if required) shall be mitred cut and fusion welded/mechanically jointed duly sealed at all corners, including drilling of holes for fixing hardware and drainage of water etc. After fixing frame the gap between frame and adjacent finished wall shall be filled with weather proof silicon sealant over backer rod of approved size and quality, all complete as per approved drawing conforming to CPWD specification & direction of Engineer-in-Charge. Section of steel reinforcement and cross sections of uPVC profiles to be as per design approved by Engineer-in-Charge. Three track three panels sliding window with Aluminium channel for roller track, wool pile, nylon rollers with SS 304 body. Using R4 series with frame (115 mm & above) x (45 mm & above) & sash (44 mm & above) x (55 mm & above) with zinc alloy (zamak) powder coated handle on two end panels along with multi-point locking system. As per DSR 9.147.A5.3 |
| 34 | Providing and fixing tiled false ceiling of specified materials of size 595x595 mm in true horizontal level, suspended on interlocking metal grid of hot dipped galvanized steel sections ( galvanized @ 120 grams/ sqm, both side inclusive) consisting of main “T” runner with suitably spaced joints to get required length and of size 24x38 mm made from 0.30 mm thick (minimum) sheet, spaced at 1200 mm center to center and cross “T” of size 24x25 mm made of 0.30 mm thick (minimum) sheet, 1200mm long spaced between main “T” at 600 mm center to center to form a grid of 1200x600 mm and secondary cross “T” of length 600 mm and size 24x25 mm made of 0.30 mm thick (minimum) sheet to be interlocked at middle of the 1200x600 mm panel to form grids of 600x600 mm and wall angle of size 24x24x0.3 mm and laying false ceiling tiles of approved texture in the grid including, required cutting/making, opening for services like diffusers, grills, light fittings, fixtures, smoke detectors etc. Main “T” runners to be suspended from ceiling using GI slotted cleats of size 27 x 37 x 25 x1.6 mm fixed to ceiling with 12.5 mm dia and 50 mm long dash fasteners, 4 mm GI adjustable rods with galvanized butterfly level clips of size 85 x 30 x 0.8 mm spaced at 1200 mm center to center along main T, bottom exposed width of 24 mm of all T-sections shall be pre-painted with polyester paint, all complete for all heights as per specifications, drawings and as directed by Engineer-in-charge 8 mm thick fully perforated calcium silicate board made with Calcareous & Siliceous materials reinforced with cellulose fiber manufactured through autoclaving process to give stable crystalline structure with minimum compressive strength 225 kg/ sq. cm, bending strength 100 kg/sq. cm , of size 595x595 mm, having perforation of dia. 10 mm with minimum perforated area 18 % with non woven tissue on the back side, having an NRC ( Noise Reduction Coefficient) of 0.85, with 50 mm thick rockwool of 48 kg /cum backing. as per DSR 12.58.1 |
| 35 | Providing and fixing in wall lining flat pressed three layer (mediumdensity) particle board or graded wood Pre-laminated one side decorative lamination and other side balancing lamination Grade I, Type II, IS : 12823 marked, including priming coat on unexposed arrangement and screws etc. complete 25 mm thick as per DSR 8.26.3 |
| 36 | Providing and fixing aluminium extruded section body tubular type universal hydraulic door closer ( having brand logo with isi 3564 embosed on body ) with double speed adjustment with necessary accessories and screw etc complete as per DSR 9.84 |
| 37 | Providing and fixing bright finished brass 100mm mortice latch and lock with 6 levers and a pair of lever handle of approved quality with necessary screw etc complete as per DSR 9.76 |
| 38 | Steel work welded in built up sections / framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer using structural steel etc. In grantings, frames, guard bar, ladder, railing, brackets, gates and similar works as per Code No. 10.25.2 |
| 39 | Providing and fixing circular/ Hexagonal cast iron or M.S. sheet box for ceiling fan clamp, of internal dia 140 mm, 73 mm height, top lid of 1.5 mm thick M.S. sheet with its top surface hacked for proper bonding, top lid shall be screwed into the cast iron/ M.S. sheet box by means of 3.3 mm dia round headed screws, one lock at the corners. Clamp shall be made of 12 mm dia M.S. bar bent to shape as per standard drawing.As per DSR Code No. 10.18 |
| 40 | Cement concrete flooring 1:2:4 (1 cement: 2 coarse sand : 4 graded stone aggregate) finished with a floating coat of neat cement, including cement slurry, but excluding the cost of nosing of steps etc. complete.40 mm thick with 20 mm nóminal size stone aggregate.As per DSR Code No.11.3.1 |
| 41 | Wiring point for Light ,fan ,exhaust fan etc with 1.5sq. mm. FR PVC insulated multistrand single core copper cable in PVC conduit with 1.5 sq.mm. FR PVC-insulated multistrand Copper conductor cable as earth wire drawn in side the conduit. Add for light/f |
| 42 | Wiring point for plug with 1.5 sq.mm FRLSH PVC insulated multistrand single core copper conductor cable in PVC conduit pipe Partly concealed in the wall and partly Laid in slab along with the reinforcement before concreting ,complete with 1.5sqmm. FRLS |
| 43 | Supply fixing & concealing of PVC conduit in the wall including cutting of brick laying of conduit & fixing it with MS hooks & then plastering.with cement, sand,mortar finished to the level,with matching colour wash including cost of proper thrading of c |
| 44 | Supply & wiring of submains with 2 nos.2.5 sq.mm FRLSH PVC insulated 1100 V grade multistrand single core copper conductor cable in 20 mm dia heavy gauge PVC conduit partly concealed in wall and partly laid in slabalong with the reinforcement before conc |
| 45 | Wiring for circuit/ submain wiring alongwith earth wire with the following sizes of FRLS PVC insulated copper conductor, single core cable in surface/ recessed medium class PVC conduit as required. 2 X 1.5 sq. mm + 1 X 1.5 sq. mm earth wire. |
| 46 | Supply & wiring of submains with 2 nos.4 sq.mm FRLSH PVC insulated 1100 V grade multistrand single core copper conductor cable in 20 mm dia heavy guage PVC conduit partly concealed in wall and partly laid in slab along with the reinforcement before concr |
| 47 | Supply and fixing of 63 amp DP 30 mA ELCB/ RCCB of Din Rail mounting in DB complete in all respect with connections as required. |
| 48 | Supply & fixing and making connection of 63 amp. 4P 30 mA ELCB/ RCCB of Din Rail mounting in complete in all respect as per direction and satisfaction to the Engineer in Charge. |
| 49 | Supply & fixing of Batton/Angle holder including making connection etc. as required. |
| 50 | Supply and fixing of 240 volts C Curve 6-32 amp SP miniature circuit breaker (10 K A ) in existing MCB, DB complete with connections as required. CAT A |
| 51 | LED Down lighter (SMD Type) (System lumen efficacy ≥120 <135 lm/Watt ) Supplying, installation, Testing & Commissioning of LED Recessed / surface Down lighter (Round / square/ Rectangular) SMD type of following body material with PMMA and prismatic d |
| 52 | Supply of ceiling fans with fan mortar of AC permanent insulation ,capacitor rating confirming BEE 5 star rating and IS:374/79 and also comply with IS:1709/1984 with latest amendment.The rated voltage 220/240 volts 50hz,1-ph AC the fan assemble should con |
| 53 | Providing and fixing water closet squatting pan (Indian type W.C. pan ) with 100 mm sand cast Iron P or S trap, 10 litre low level white P.V.C. flushing cistern, including flush pipe, with manually controlled device (handle lever) conforming to IS : 7231, |
| 54 | Providing and fixing wash basin with C.I.brackets, 15 mm C.P. brass pillar taps, 32 mm C.P. brass waste of standard pattern, including painting of fittings and brackets, cutting and making good the walls where required : White Vitreous China Wash basin |
| 55 | Providing & fixing PVC waste pipe for sink oncluding PVC waste fitting Complete Flexible Pipe 32mm Dia |
| 56 | Providing and fixing mirror of superior glass (of approved quality) and of required shape and size with plastic moulded frame of approved make and shade with 6 mm thick hard board backing : Rectangular shape 1500x450 mm |
| 57 | Providing and fixing 600x120x5 mm glass shelf with edges round off, supported on anodised aluminium angle frame with C.P. brass brackets and guard rail complete fixed with 40 mm long screws, rawl plugs etc., complete. |
| 58 | Providing and fixing toilet paper holder : C.P. brass |
| 59 | Providing and fixing MS holder bat clamps of approved design to cast iron (spun) pipe embedded in and Including cement concrete blocks 10 x10 x10cm of 1:2:4 mix (1 cement : 2 coarse sand : 4 graded stone aggregate 20mm nominal size) including cost of cutt |
| 60 | Providing and fixing cpvc pipe i/c all complete on concealing work 15 mm dia nominal bore |
| 61 | Providing and fixing cpvc pipe i/c all complete on concealing work 20 mm dia nominal bore |
| 62 | Providing and fixing of gun metal gate valve with CI wheel of approved quality (screwed ends) 25mm dia, nominal bore |
| 63 | Providing and fixing uplasticised PVC connection pipe with brass unions : 15 mm nominal bore |
| 64 | Providing and fixing C.P. brass shower rose with 15 or 20 mm inlet 100 mm diameter |
| 65 | Providing and fixing C.P. brass bib cock of approved quality confirming to IS:8931 15mm nominal bore |
| 66 | Providing and placing on terrace polythylene water storage tank IS 12701 marked with cover and suitable locking arrangement and making necessary hole for inlet outlet and overflow. |
| 67 | Providing and fixing soil, waste, vent pipes 100mm dia cast (spun) iron S&S pipe |
| 68 | Suppply and fixing of sign board I/C all. |
| 69 | As per Order of Joint Secretary G.O.No.G-1877 Dated-21-02-2025 and Dierector cum-Chief Engineer U.P.RED, LucknowLetter No.801 Dated 03-03-2025 Deduction 5 % for Competative Price Efficiency Please Enable Macros to View BoQ information |
AI Tender Summary
Tender Timeline
Jul 15, 2026
11:30 IST
Tender Published
Tender notice published.
CompletedJul 27, 2026
17:00 IST
Bid Submission Deadline
Online submission via eProcurement portal.
Upcoming · 11 daysJul 28, 2026
Bid Opening Date
Technical bids will be opened and evaluated.
Upcoming · 12 daysTender Documents
Download All (ZIP) ↓
Disclaimer
We takes all possible care for accurate & authentic tender information. However users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender