Tender For Procurement Of Furniture For School Building At Various Places In Ut Of D&Nh.
Tender Value
36.10 Crore
Estimated cost
Bid Submission
07 Aug 2026
22 days left
EMD
46.11 Lakhs
Bank guarantee accepted
Document Fee
15000
Non-refundable
Tender Type
Online
Tender Overview
Organization
Tender ID
Competition Type
NCB
Bidding Type
Tender
Location / State
Dadra and Nagar Haveli → Dadra and Nagar Haveli
EMD Exemption
Not Available
Quantity
Not Available
Website
Contact Person
Address
Project Description
Tender for Procurement Of Furniture For School Building At Various Places In Ut Of D&Nh.
BOQ
| Sl. No. | Item Description |
| 1 | Providing and Fixing RECTA WORKSTATIONS - 900 x 600 - APOProviding and placing \\"UPBEAT\\"desk based modular workstation with System ht - 1200 mm. PARTIAL SCREENS: Fabric Magnetic T- mould, 19mm thk Screen of 450mm ht.,mounted on Studs.LEGS: Providing metal powder coated Cube leg. Legs are for standard workstation height of 750mm. UNDERSTRUCTURE: Comprising of metal powder coated cross connectors between legs and legs. Made up of metal powder coated finish and the entire assemply is fixed to the worktop.WIRE MANAGEMENT: For 750 high workstations- For vertical wiremenagement, Shared legs with cover are considere. For horizontal wiremanagement - Wire Tray with integrated power box. Access flap will be provided. Switch plate of (8+3 Anchor Roma) module is considered for Power and Data points. WORKSURFACE - Out of 25 mm thk prelam particle board with flat pvc lipping edge banding of size 900 mm w x 600 mm d.\\"MODESTY : Metal modesty: Lazer cut perforated Metal modestyMetal and wooden modesty are mounted on the worktop with the help of the modesty mounting brackets Modesty terminates at 400 mm from ground.\\"CPU trolley - with castorsKBPT with mousetray - Metal as directed by Engineer In-charge (As per specified in Technical specification of furniture Page No.30 of NIT) |
| 2 | Providing and Fixing Meeting table Providing and placing \\"UPBEAT\\" conference tables with worktop ht - 750 mm. Cube legs are fabricated by Argo Shield & have a square section. Cube legs are available for work top level 750 mm from base .Wire Management Single Power box (8M+3M & 8M+3M Anchor Roma)with raiser and Soft closing dual access flap with brush.Worktop: 25mm thk prelaminated partical board with pvc lipping. Dimension - 2100*900Warranty - 2 YearsMake - (As per specified in Technical specification of furniture Page No.30 of NIT) |
| 3 | Providing and Fixing 1500*600*750HMain WorktopMade of 25mm Thick Pre-laminated board (PLB) of E1-P2 grade and approved shade confirming to IS-12823:1990, Edge banded with matching 2 mm thick PVC lipping. Access Flap provided on work surface for wire managementReturn WorktopMade of 25mm Thick Pre-laminated board (PLB) of E1-P2 grade and approved shade confirming to IS-12823:1990, Edge banded with matching 2 mm thick PVC lipping.Modesty PanelMade of 18mm Thick Pre-laminated twin board (PLT) of E1-P2 grade and approved shade confirming to IS-12823:1990, Edge banded with matching 2 mm thick PVC lipping.LegsCube legs are fabricated from MS ERW Tube of 50 mm x 25 mm x 1.2 mm thick and 40 mm x 40 mm x 1.2 mm thick (as per IS: 7138). At the top surface of leg, support brackets of 3 mm thick HR (as per IS: 2062) are welded for fixing worktop. These are welded together by argo shield welding. This welded structure is coated with 50 micron epoxy polyester coating. At the base, a plastic cap with M8 molded insert is fixed, on which a straight M8 lever fitted which allows for adjustment of the height upto 50mm.Warranty - 2 Years Make - (As per specified in Technical specification of furniture Page No.30 of NIT) |
| 4 | Providing and Fixing The understructure is in prelam panels, made with PLT boards. 2-Drawer and 3-Drawer storage units with different combinations to support Tops, made with 18mmPLT boards of different colours. Modesty and back panels, made with 18mm PLT boards as directed by Engineer In-charge (As per specified in Technical specification of furniture Page No.30 of NIT) |
| 5 | Providing and Fixing MEETING TABLE - SQUARE (APO) Providing and placing \\"UPBEAT\\"desk based modular workstation with System ht - 750 mm. LEGS: Providing metal powder coated cube leg. UNDERSTRUCTURE: Comprising of metal powder coated cross connectors between legs and legs. Made up of metal powder coated finish and the entire assemply is fixed to the worktop. WIRE MANAGEMENT: NA WORKSURFACE - Out of 25 mm thk prelam particle board with flat pvc lipping edge banding of size 750 MM W X 750 MM D Note: All legs have levelling screws for adjustment in case of Uneven floor to take care of +/- 50 mm of uneven flooring. as directed by Engineer In-charge (As per specified in Technical specification of furniture Page No.30 of NIT) |
| 6 | Providing and Fixing Finesse Table TABLE TOP / SIDE PANEL 25 ± 0.5 MM THICK PLAIN PARTICLE BOARD (PPB) AS PER IS-3087 CLAD WITH 0.6MM THICK POST FORMED LAMINATE AND 1MM THICK BACKING LAMINATE (BDL). FLAT EDGE DULY SEALED WITH 2MM THICK PVC BEADING. MODESTY 18 ± 0.5 MM THICK PLAIN PARTICLE BOARD (PPB) AS PER IS-3087 CLAD WITH 1.0MM THICK DECORATIVE LAMINATE (DL) ON BOTH SIDES. EDGE SEALED WITH 2MM THICK PVC BEADING. RETURN UNIT TOP / SIDE PANEL 25 ± 0.5 MM THICK PLAIN PARTICLE BOARD (PPB) AS PER IS-3087 CLAD WITH 0.6MM THICK POST FORMED LAMINATE AND 1MM THICK BACKING LAMINATE (BDL). FLAT EDGE DULY SEALED WITH 2MM THICK PVC BEADING. MODESTY 18 ± 0.5 MM THICK PLAIN PARTICLE BOARD (PPB) AS PER IS-3087 CLAD WITH 1.0MM THICK DECORATIVE LAMINATE (DL) ON BOTH SIDES. EDGE SEALED WITH 2MM THICK PVC BEADING. HINGED DRAWER UNIT TOP / SIDE PANEL 25 ± 0.5 MM THICK PLAIN PARTICLE BOARD (PPB) AS PER IS-3087 CLAD WITH 0.6MM THICK POST FORMED LAMINATE AND 1MM THICK BACKING LAMINATE (BDL). FLAT EDGE DULY SEALED WITH 2MM THICK PVC BEADING. DOORS, PARTITIONS & SHELVES 18 ± 0.5 MM THICK PLAIN PARTICLE BOARD (PPB) AS PER IS-3087 CLAD WITH 1.0MM THICK DECORATIVE LAMINATE (DL) ON BOTH SIDES. EDGE SEALED WITH 2MM THICK PVC BEADING.1500 X 750 X 7401050 X 450 X 705 as directed by Engineer In-charge (As per specified in Technical specification of furniture Page No.30 of NIT) |
| 7 | Providing and Fixing 1200*600*750HMain Worktop Made of 25mm Thick Pre-laminated board (PLB) of E1-P2 grade and approved shade confirming to IS-12823:1990, Edge banded with matching 2 mm thick PVC lipping. Access Flap provided on work surface for wire management Return Worktop Made of 25mm Thick Pre-laminated board (PLB) of E1-P2 grade and approved shade confirming to IS-12823:1990, Edge banded with matching 2 mm thick PVC lipping. Modesty Panel Made of 18mm Thick Pre-laminated twin board (PLT) of E1-P2 grade and approved shade confirming to IS-12823:1990, Edge banded with matching 2 mm thick PVC lipping. Legs Cube legs are fabricated from MS ERW Tube of 50 mm x 25 mm x 1.2 mm thick and 40 mm x 40 mm x 1.2 mm thick (as per IS: 7138). At the top surface of leg, support brackets of 3 mm thick HR (as per IS: 2062) are welded for fixing worktop. These are welded together by argo shield welding. This welded structure is coated with 50 micron epoxy polyester coating. At the base, a plastic cap with M8 molded insert is fixed, on which a straight M8 lever fitted which allows for adjustment of the height upto 50mm. as directed by Engineer In-charge (As per specified in Technical specification of furniture Page No.30 of NIT) |
| 8 | Providing and Fixing NOVA FREE STANDING PEDESTAL WITH FLAT METAL FRONT OF SIZE 390W X 585D X 646HT, 1DR = 1 BOX + 1 FILE, CENTRAL LOCKING. Note - This is Storage for T-20 Table or Upbeat Workstation Penta as directed by Engineer In-charge (As per specified in Technical specification of furniture Page No.30 of NIT) |
| 9 | Providing and Fixing KD Storwel Plain Plain: 900 mm (W) × 450 mm (D) × 1830* mm (H) Full height steel hinged door Plastic Recessed Handle cum Cam Lock 3 way locking mechanism with shooting bolt arrangement. Height wise Adjustable Shelf Mounting • Uniformly Distributed Load Capacity per each full/half shelf is 40 Kg maximum.• Plain 4s : 4 Nos. of Adjustable Full Shelves• Plain 3s : 3 Nos. of Adjustable Full Shelves Kd Storwel Plain 4s – The A4 size Box file (85Wx345Hx285D) can be stored vertically on three shelves and the clear space above fourth shelf is 180mm.Kd Storwel Plain 3s – The A4 size Box file (85Wx345Hx285D) can be stored vertically on three shelves.Warranty - 2 Years Make - (As per specified in Technical specification of furniture Page No.30 of NIT) |
| 10 | Providing and Fixing Minor: 900 mm (W) x 450 mm (D) x 1167.5 mm (H) Rigid Knock down construction. Prime Quality CRCA** Steel – Panels from 0.6 mm thick (±0.07mm) & Front frame, Shelf 0.8 mm thick (±0.08mm).**CRCA ‘D’ grade as per IS:513 Full height Steel Hinged Door Plastic Recessed Handle cum Cam Lock 3 way locking mechanism with shooting bolt arrangement. Minor : 2 Nos. of Adjustable Full Shelves Kd Storwel Minor – Box file A4 size (85Wx345Hx285D) can be stored vertically on two shelves and the clear space above third shelf is 280mm.Warranty - 2 Years Make - (As per specified in Technical specification of furniture Page No.30 of NIT) |
| 11 | Providing and Fixing Model Plain with 4S 2. Product Size 916 mm (W) × 486 mm (D) × 1980 mm #(H) – Excluding Leveler3. Construction & Material• Welded construction• 0.7 mm thk (±0.07 mm) CRCA* for shelf• 0.8 mm thk (±0.08 mm) High yield strength CRCA** for doors and back• 0.9 mm thk (±0.08 mm) CRCA* for all other components*CRCA ‘D’ grade as per IS:513**CRCA ‘D’ grade high yield strength as per IS:5134. Locking & handle• Mazak handle• Three way locking mechanism with shooting bolt5. Shelving• Height wise adjustable shelf mounting• Uniformly Distributed Load Capacity per each full shelf is 40 Kg maximum• 4 Nos. of adjustable full Shelf• Box file A4 size (85W × 345H × 285D) can be stored vertically on three shelves and the clear space above fourth shelf is 240mm6. Leveler• M10 screw type leveler with hex plastic base7. Finish• Epoxy Powder coated to the thickness of 50 microns (±10) Make - Warrant 1 year as directed by Engineer In-charge (As per specified in Technical specification of furniture Page No.30 of NIT) |
| 12 | Providing and Fixing Glassdoor Storwel 2. Product Size 916 mm (W) × 486 mm (D) × 1980 mm #(H) – Excluding Leveler3. Construction & Material• Welded construction• 0.7 mm thk (±0.07 mm) CRCA* for shelf• 0.8 mm thk (±0.08 mm) High yield strength CRCA** for doors and back• 0.9 mm thk (±0.08 mm) CRCA* for all other components*CRCA ‘D’ grade as per IS:513**CRCA ‘D’ grade high yield strength as per IS:5134. Locking & Handle• Zinc Alloy handle• Two way locking mechanism with shooting bolt5. Shelving• Height wise adjustable shelf mounting• Uniformly Distributed Load Capacity per each full shelf is 40 Kg maximum. Make - warranty 1 years. as directed by Engineer In-charge (As per specified in Technical specification of furniture Page No.30 of NIT) |
| 13 | Providing and Fixing Radiance Book Rack (1200W X 600D) Single Body comes with four widths (1200W, 2400W, 3600W & 4800W) with 300D. Single body 1200W/2400W/3600W/4800W with 300D: Single Body 1200W : 1200 × 2078 × 300 Single Body 2400W : 2400 × 2078 × 300 Single Body 3600W : 3600 × 2078 × 300 Single Body 4800W : 4800 × 2078 × 300 25 mm will be added on both sides for wooden front. Height is including leveler at zero position. There is leveling adjustment up to 50 mm. Placement Single body bookrack should always be placed against the wall. Body a. Side panels, Frame & Cross L bracket are made using 0.8 mm CRCA (IS:513). b. The assembly consists of 2 tie rods, 4 fixing brackets and 2 turnbuckles. Tie rods are fixed in “X” shape Tie rods are of 4 mm dia MS wire Fixing brackets are made of 2 mm thick CRCA IS:513 grade c. Optional wooden panel of 25 mm thick PLT, E1-P2 grade board for PLT ref. Specification – FF04/DSN/STD/101, edges with machine pressed 2 mm PVC lipping glued with hot melt EVA glueUnder Structurea. Under structure is made of 0.8 mm CRCA (IS:513)b. Sizes of under structure (single body):1200W × 295D × 80H2400W × 295D × 80HShelvesa. Shelves used are 10 bend panel made of 0.8 mm CRCA (IS:513)b. Shelf panels are placed on shelf support and then fixed using nut and bolts from belowc. Standard configuration consists of 6 loading levels formed by 5 adjustable shelves for each main and add-on unitd. Uniformly Distributed Load Capacity per each shelf is 80 Kg maximumConstructionCompletely knock-down constructionFinishAll MS sheet metal and metal frame components are powder coated with epoxy polyester powder to a minimum thickness of 45 microns as directed by Engineer In-charge (As per specified in Technical specification of furniture Page No.30 of NIT) |
| 14 | Providing and Fixing Pisa Sofa 3 seaterThe seat is made up of PU foam in Density 28 ±2 kg/cu.mtr with an additional top layer of supersoft PU foam in Density 32 ± 2 kg/cu, upholstered with fabric or leatherette. 2) BACK FOAM: The back is made up of PU foam in Density 28 ± 2 kg/cu. mtr with two additional top layer of supersoft foam of density 32±2 kg/cu. mtr, upholstered with fabric or leatherette. 3) UNDERSTRUCTRE : Understructure is made up of 1.2±0.1 cm. thick hot pressed plywood [moisture resistance & termite proof as per IS:303] & pinewood of cross sections devoid of major knots & surface defects. 6 nos. per seat & 3.8mm Dia zigzag spring assembly is mounted over understructure for cushioning purpose. 4) LEG ASSEMBLY: It is a welded Assembly made in Stainless steel (grade SS 202) tube & plate with plastic endcap. Make - Warranty 1 years. as directed by Engineer In-charge (As per specified in Technical specification of furniture Page No.30 of NIT) |
| 15 | Providing and Fixing Pisa Sofa 2 seaterThe seat is made up of PU foam in Density 28 ±2 kg/cu.mtr with an additional top layer of supersoft PU foam in Density 32 ± 2 kg/cu, upholstered with fabric or leatherette. 2) BACK FOAM: The back is made up of PU foam in Density 28 ± 2 kg/cu. mtr with two additional top layer of supersoft foam of density 32±2 kg/cu. mtr, upholstered with fabric or leatherette. 3) UNDERSTRUCTRE : Understructure is made up of 1.2±0.1 cm. thick hot pressed plywood [moisture resistance & termite proof as per IS:303] & pinewood of cross sections devoid of major knots & surface defects. 6 nos. per seat & 3.8mm Dia zigzag spring assembly is mounted over understructure for cushioning purpose. 4) LEG ASSEMBLY: It is a welded Assembly made in Stainless steel (grade SS 202) tube & plate with plastic endcap. Make - Warranty 1 years. as directed by Engineer In-charge (As per specified in Technical specification of furniture Page No.30 of NIT) |
| 16 | Providing and Fixing Pisa Center Table -112W x 60D x 35.1H Understructure in buff polished Stainless Steel grade 202. • Table Top with rectilinear form with rounded boundaries and chamfered edges give it crisp and formal visual appearance.12mm thick Glass top is scratch resistant Make - Warranty 1 years. as directed by Engineer In-charge (As per specified in Technical specification of furniture Page No.30 of NIT) |
| 17 | Providing and Fixing # Providing and placing \\"UPBEAT\\" meeting tables with worktop ht - 750 mm. Cube legs are fabricated by Argo Shield & have a square section. Cube legs are available for work top level 750 mm from base. Wire Management Single Power box (8M+3M & 8M+3M Anchor Roma)with raiser and Soft closing dual access flap with brush. as directed by Engineer In-charge (As per specified in Technical specification of furniture Page No.30 of NIT) |
| 18 | Providing and Fixing PISA Corner table Understructure in buff polished Stainless Steel grade 202. • Table Top with rectilinear form with rounded boundaries and chamfered edges give it crisp and formal visual appearance • 12mm thick Glass top is scratch resistant. Warranty 1 years Make -. as directed by Engineer In-charge (As per specified in Technical specification of furniture Page No.30 of NIT) |
| 19 | Providing and Fixing Slotted angle rack - 1300W as directed by Engineer In-charge (As per specified in Technical specification of furniture Page No.30 of NIT) |
| 20 | Providing and Fixing Genii SM2 -1240 x 990 x 537 All side metal frames and cross connectors are made from combination of 25.4 × 1.2 mm thk (approx. 18 SWG) Round ERW tubes, 31.8 × 1.2 mm thk (approx. 18 SWG) Round ERW tubes and 28.6 × 1.2 mm thk (approx. 18 SWG) Round ERW tubes (as per IS:7138) which are welded together. The welded structures and cross connectors are coated with minimum 45 micron thickness of epoxy polyester coating. Back supports which are provided at the rear back are made of 50.0 × 25.0 × 1.2 mm thk (approx. 18 SWG) rectangular ERW tubes (as per IS:7138). The tubes are coated with minimum 45 micron thickness of epoxy polyester coating. The storage shelves are made from 0.6 mm thk MS sheet (as per IS:513) fixed below the desktop panel and are coated with minimum 45 micron thickness of epoxy polyester coating. Hooks are provided on the vertical side frames on both sides of the desk for hanging bags/bottles. They are made from 2 mm thk MS sheet (as per IS:513) and are coated with minimum 45 micron thickness of epoxy polyester coating. The understructure is assembled using M6 trilobular screws (as per DIN 7500) with Zn blue plating (as per IS 1573:1986). Compact laminate seat and back panels are assembled using M6 countersunk trilobular screws (as per DIN 7500) with Zn black plating (as per IS 1573:1986). Spacers are provided on the top of round tubes for wooden panels fixing. They are made of PP glass-filled (30%). Plastic caps made of PP copolymer (3530 grade) are also provided on the rear frames adding more aesthetic value to the product. M6 high tensile TVS make bolt (Class 8.8) with glass-filled nylon level adjustors are provided at the bottom of understructure to take care of unevenness in floor with height adjustment of approx. 15 mm as directed by Engineer In-charge (As per specified in Technical specification of furniture Page No.30 of NIT) |
| 21 | Providing and Fixing Dimension - 1050*998*757Genii APO All side metal frames and cross connectors are made from a combination of 25.4 × 1.2 mm thick (approx. 18 SWG) round ERW tubes and 31.8 × 1.2 mm thick (approx. 18 SWG) round ERW tubes (as per IS:7138), which are welded together. The welded structures and cross connectors are coated with a minimum 45 micron thickness of epoxy polyester coating. Back supports provided at the rear are made of 50.0 × 25.0 × 1.2 mm thick (approx. 18 SWG) rectangular ERW tubes (as per IS:7138). The tubes are coated with a minimum 45 micron thickness of epoxy polyester coating. The storage shelves are made from 0.6 mm thick MS sheet (as per IS:513), fixed below the desktop panel and coated with a minimum 45 micron thickness of epoxy polyester coating. Hooks are provided on the vertical side frames on both sides of the desk for hanging bags/bottles. These hooks are made from 2 mm thick MS sheet (as per IS:513) and are coated with a minimum 45 micron thickness of epoxy polyester coating. The understructure is assembled using M6 trilobular screws (as per DIN 7500) with zinc blue plating (as per IS 1573:1986). Spacers are provided on the topof round tubes for fixing wooden panels. These spacers are made of PP glass-filled material (30%). Plastic caps made of PP copolymer (3530 grade) are also provided on the rear frames to enhance the aesthetic value of the product. M6 high tensile TVS make bolt (Class 8.8) with glass-filled nylon level adjusters are provided at the bottom of the understructure to accommodate uneven floor surfaces, with a height adjustment of approximately 15 mm. as directed by Engineer In-charge (As per specified in Technical specification of furniture Page No.30 of NIT) |
| 22 | Providing and Fixing Dimension - 1200*910*750The panels are made from 18 mm thick Pre-Laminated Boards as per (IS:12823) with PVC edge banding on all sides.UNDERSTRUCTURE:Side frame (LH & RH):• LH / RH frames are made of MS ERW tubes as per (IS:7138) Sq. 25.4 mm × 1.2 mm thick, which are welded to the desk and seat C-shaped support brackets that are made of 1.2 mmthick MS.• All frames are powder coated 50 microns (±10). Stiffeners:• Stiffeners provided between the LH / RH vertical frames at the base and rear of the seat are made from MS ERW tubes as per (IS:7138) Sq. 25.4 mm × 1.2 mm thick.• Stiffeners provided between the LH / RH vertical frames under the desk and the seat panelare made from ERW tubes as per (IS:7138) Sq. 25.4 mm × 1.2 mm thick.• Additional horizontal supports of 1.5 mm thick MS ‘C’ sections are provided between the LH / RH vertical frames behind the back panel to add rigidity to the structure.• They are powder coated 50 microns (±10).• The understructure is assembled using M5 trilobular taptite screws.• All open ends of understructure frame are closed with plastic caps.• Nylon studs are provided on the base of LH / RH frames as directed by Engineer In-charge (As per specified in Technical specification of furniture Page No.30 of NIT) |
| 23 | Providing and Fixing Thrill Cushions Executive The back is made up of 1.2 ±0.1cm. thick hot-pressedplywood & seat is made up of 1.5 ±0.1cm. thick hot-pressed plywood measured as per QA methoddescribed in OCP-QLTA-P14-18 and upholstered with fabric upholstery covers and moulded Polyurethane foam. The back foam is designed with contoured foam lumbar support. The seat has extra thick foam on front edge to give comfort to popliteal area.The Recron filling done in seat & back ( Executive chairs only) for extra fluffiness and comfort in chair. The chair seat & back size are *HIGH BACK SIZE 51.5 cm. (W) x 82.0 cm. (H) *FULL BACK SIZE 51.5 cm. (W) x 69.0 cm. (H) *SEAT SIZE 53.5 cm. (W) x 51.0 cm. (D) as directed by Engineer In-charge (As per specified in Technical specification of furniture Page No.30 of NIT) |
| 24 | Providing and Fixing Thrill Visitor It is a single shell 1.2 ±0.1cm. thick hot pressed plywood with moulded polyurethane foam on top & backing foam on rear side. It is upholstered with option of knitted & leatherette fabric.The seat has extra thick foam on front edge to give comfort to popliteal area.The foam backing done in back ( Executive chairs only) for extrafluffiness and comfort in chair.The HR polyurethane foam for seat and back is moulded with density 45 +/-2 kg/m³ and Hardness load 16 ± 2 kgf as per IS:7888 at 25% compression.: The powder coated (DFT 40-60 micron) tubular frame is cantilever type & made of Ø2.54±0.03 cm x 0.2±0.016 cm thk MS ERW tube. as directed by Engineer In-charge (As per specified in Technical specification of furniture Page No.30 of NIT) |
| 25 | Providing and Fixing Relax 4 legs with arm; without castor MS Understructure, Mesh back, With/without arms and with/without castors.Stackable only for variants without castor.White Body with Mesh - Black & White Woven Black Body with black mesh Seat - FK01,, FK07, , FK10, FK18 as directed by Engineer In-charge (As per specified in Technical specification of furniture Page No.30 of NIT) |
| 26 | Providing and Fixing Unwind Café Chair 1. Seat / Back Material: Injection moulded high impact Polypropylene with UVresistance Seat Size: 52.5 cm (W) × 53.2 cm (D) Back Size: 51.6 cm (W) × 40.5 cm (H) 2. M.S. Powder Coated Understructure Welded tubular frame Tube sizes: Ø 2.22 ± 0.03 cm × 0.16 ±0.0128 cm 3.5 ± 0.03 cm × 1.5 ± 0.03 cm × 0.16 ± 0.0128 cm Powder coating thickness: 50 ± 10 microns 5. Shoe Polypropylene with UV resistance Press-fitted to tubular frame 6. Armrest Polypropylene with UV resistance Mounted on tubular frame as directed by Engineer In-charge (As per specified in Technical specification of furniture Page No.30 of NIT) |
| 27 | Providing and Fixing LAB STOOL - Mch Ht Adj + back Hi Baseas directed by Engineer In-charge (As per specified in Technical specification of furniture Page No.30 of NIT) |
| 28 | Providing and Supply Dustbin Material : SS 200; Material Thickness: 0.4MM sheet; Weight: 0.585 kg; Volume: 6 litre as directed by Engineer In-charge (As per specified in Technical specification of furniture Page No.30 of NIT) |
| 29 | Providing and Fixing Burrow Cubby 16FW All side panels,top/bottom panels, and shelf panels are made from 18mmthick pre–laminated board of E1-P2 grade and approved shade confirming to IS 12823:1990 with 2mm thick PVC edge lipping. Back panel is made from 9mm thick pre–laminated board with 0.8mm thick PVC edge lipping.Metal Frame : The Metal Frame is fabricated by Argo Shield welding of MS ERW Tube 40 mm x 20 x 1.2 mm thk (IS:7138) along with 3mm thk HR (IS2062) L-shaped plate on both sides of the frame. Dia 28 MS Bar is used as a bush for supporting the levelers at the bottom of the frame. M10 leveler molded with Nylon-6 along with a circular powder coated aluminium extrusion is used for height adjustment upto 20mm. Name Tag made out of Clear Polycarbonate is provided with200 GSM paper as directed by Engineer In-charge (As per specified in Technical specification of furniture Page No.30 of NIT) |
| 30 | Providing and Fixing Gainpro Locker Height including leveler Height of leveler is 50mm and adjustment possible is15mm. 02. Construction & Material • Aesthetically appealing completely knock down construction.• The add-on units are stack widthwise to form a row of lockers.(Note– Single Main unit should not be offered. Minimum 1 Main + 1Addon to be offered)Maximum 1Main + 4Addon to be offered)• Legs fitted with screw type leveler.• Made from combination of Top panel(0.5mm CRCA), side panel(0.5mm CRCA), Bottompanel(0.5mm CRCA), Back panel(0.5mm CRCA), Top Bottom stiffener(1.2mm CRCA) and EndCover(0.5mm CRCA).** – CRCA ‘D’ Grade as per IS–513.Warranty - 2 YearsMake - (As per specified in Technical specification of furniture Page No.30 of NIT) |
| 31 | Providing and Fixing Rigid knock-down construction with 0.7 mm thick CRCA steel top, side and back panels, and 0.8 mm thick CRCA steel doors, bottom and shelves conforming to IS 513 Grade D. Available in 2-door and 4-door configurations. Doors fitted with cam locks, 4 mm thick transparent toughened glass vision panels secured with rubber gaskets, scissor-type receding mechanism for parallel smooth movement, and plastic end-cap handles. Each compartment includes a storage shelf with a uniformly distributed load capacity of 80 kg pershelf. Top panel options include metal top panel (4-door model) and 18 mm thick PLB straight-edge top with PVC lipping (2-door model). Epoxy polyester powder-coated finish with coating thickness of 50 ± 10 microns.Provide your feedback on BizChat - APO Bookcase 1742 H x 800W x 320 D as directed by Engineer In-charge (As per specified in Technical specification of furniture Page No.30 of NIT) |
| 32 | Providing and Fixing 2350*2350 Dimesnion TotalPrimary Work SurfaceMade of 25mm thick MDF-one side pre-laminate board confirming to IS-14587:1998 with 0.4mmPVC membrane pressed on to top. Softclosing access flap with in-build power box are provided onwork surface for wire management.Secondary Work SurfaceMade of 25mm thick MDF-one side pre-laminate board confirming to IS-14587:1998 with 0.4mmPVC membrane pressed on to top.Modesty PanelMade of 25mm thick MDF-one side pre-laminate board confirming to IS-14587:1998 with 0.4mmPVC membrane pressed on to top.Under-structureMade of 25mm Thick Pre-laminated twin board of E1-P2 grade and approved shade confirming toIS-12823:1990, Edge banded with matching 2 mm thick PVC lipping.Integrated PedestalMade of 25mm Thick Pre-laminated twin board of E1-P2 grade and approved shade confirming toIS-12823:1990, Edge banded with matching 2 mm thick PVC lipping. Drawer fronts made of25mm thick MDF-one side pre-laminate board confirming to IS-14587:1998 with 0.4mm PVCmembrane pressed on to top. Pedstal construction is BOX-BOX-FILE type which uses powdercoated 400 MM long metal panel drawer slides. Drawer extension is 325 MM. Drawers have a softclosing & anti slam mechanism. Handles are provided for ease of opening. Pedestals are providedwith lock for security. as directed by Engineer In-charge (As per specified in Technical specification of furniture Page No.30 of NIT) |
| 33 | Providing and Fixing Primary Work Surface -1800*900 DimensionMade of 25mm thick MDF-one side pre-laminate board confirming to IS-14587:1998 with 0.4mm PVC membrane pressed on to top. Softclosing access flap with in-build power box are provided on work surface for wire management.Secondary Work SurfaceMade of 25mm thick MDF-one side pre-laminate board confirming to IS-14587:1998 with 0.4mm PVC membrane pressed on to top.Modesty PanelMade of 25mm thick MDF-one side pre-laminate board confirming to IS-14587:1998 with 0.4mm PVC membrane pressed on to top.Under-structureMade of 25mm Thick Pre-laminated twin board of E1-P2 grade and approved shade confirming to IS-12823:1990, Edge banded with matching 2 mm thick PVC lipping.Integrated PedestalMade of 25mm Thick Pre-laminated twin board of E1-P2 grade and approved shade confirming to IS-12823:1990, Edge banded with matching 2 mm thick PVC lipping. Drawer fronts made of 25mm thick MDF-one side pre-laminate board confirming to IS-14587:1998 with 0.4mm PVC membrane pressed on to top. Pedstal construction is BOX-BOX-FILE type which uses powder coated 400 MM long metal panel drawer slides. Drawer extension is 325 MM. Drawers have a soft closing & anti slam mechanism. Handles are provided for ease of opening. Pedestals are provided with lock for security. as directed by Engineer In-charge (As per specified in Technical specification of furniture Page No.30 of NIT) |
| 34 | Providing and Fixing # UPBEAT- Modular desk based system with 1200mm ht. Dfine plus legs are fabricated by Argo Shield & have a rectangular shape. Dfine Plus legs are available for work top level 750 mm from base. Wire Tray with integrated power box & switch plate (8+3 Anchor Roma). Soft closing access flap with brush. Metal modesty: Metal modesty is made from 0.8 mm thick CRCA. Metal modesty are mounted on the worktop with the help of the modesty mounting brackets made of 3 mm thick HR Screen: 18mm thk T mold Fabric screen on studs is providing on table top. Worktop: 25mm thk prelaminated partical board with pvc lipping . Warranty - 2 Years Make -(As per specified in Technical specification of furniture Page No.30 of NIT) |
| 35 | LABProviding supply installation of Chemical Storage Base Cabinet (1000mm Wide x 1500 mm H ) with Ventilation , Storage cabinets are designed to safely store highly corrosive acids. With a full PP construction, the cabinets are completely protected from corrosion, making them the preferred choice in labs and workspaces dealing with aggressive chemicals. cabinet provides you with a storage solution that easily outperforms the metal and wooden storages. All safety claims of this product are backed by third party certification for Chemical Spot Test for 49 chemicals listed in SEFA standards, the product must be 3rd party tested as per SEFA 8P and used across various industries. The cabinet has been designed to be fully ventilated ensuring air circulation and preventing a build-up of dangerous fumes within the cabinet. The shelves comprise of removable height adjustable collection trays that are leak-proof, enhancing the safety factor of the storage units.Exhaust Provision: There is an air-duct at the back, inside the cabinet that effectively extracts fumes when connected to exhaust. Louvers are provided on the front doors to allow inward Low of fresh air.Zero-Corrosion: Full Polypropylene Body, with no exposed metal hardware, ensures there is no corrosionClosing mechanism: The cabinet has a latch to ensure proper shutting of the doors.Removable & Height- Adjustable PP Trays as Shelves: the PP Collection Trays can be removed easily, and can be height-adjusted as required.Load Bearing Capacity & Spill Containment: Each shelf can take up to 30 kgs (approx) of uniformly distributed load. The shelves are leak-proof and fully contain accidental spillages. Locking Provision: The door has provision for using a padlock to safeguard the contents of the cabinet. as directed by Engineer In-charge (As per specified in Technical specification of furniture Page No.30 of NIT) |
| 36 | Providing supply installation of CORNER WALL TABLE - 11 WITH SINK (1115L x 1115D x 900mmH)construction: Floor based Welded cabinet system having storage body should be flush face construction with intersection of vertical and horizontal members like LH and RH side panel along with front horizontal channel, back panel and bottom panel. It should be relocated anywhere easily as it is an independent unit. Cabinet should of square non-sharp edge construction. Doors should be assembled with SS-304 hinge assembly. Removable back panel should be provided to easily access the service lines running behind the cabinet benches. Intermediate horizontal channels should be provided between door and drawer. Toe-space of 90mm X 90mm is provided at front-bottom side of cabinet. Levelers are provided for easy leveling of welded cabinet. Shelf should be eight-bend panel with 20mm height. Drawer tray should be of single piece construction. Drawer should be well supported on LH and RH ball slide suspension system. Steel door and drawer front should be of double wall construction with sound dampening material filled inside. Doors should be easily removable and hinges should be easily replaceable. Knee space panel should be in 22 gauge , Cabinets are tested as per SEFA 8M standard from a SEFA approved Lab and also tested as per EN 14727 from a third party testing agency having NABL accreditation.Dimensions: W= 750 mm, D = 750 mm, H = 875 mm Configurations: 1 Shutter - 1 Nos MOC: MSCRCA: IS – 513 (1994)•Thickness: LH/RH side panels, shutter front, Bottom panel, Top front, Drawer separator, shelf, Alignment channel is of 1.2mm thk. Removable Back panel, Shutter cover, Fr. Rack strip, Top cover panel is of 0.8mmthk • Finish: Powder coating pure epoxy, thickness 40-50 microns , followed with 9 tank Pretreatment process The thickness of powder coat should be 45-50 microns, which passes the test of Salt Spray for 1000 hours. It should have a high temperature withstanding capacity with excellent electrical insulation properties.The rear portion of above accessories which is in contact with live metal should be made from thermo set material which will not melt on heating.Handle: Anodized Aluminum Recessed-Type, CTC: 160.0mm Lock: Units have a locking facility with 180° and 10 lever cam lock mechanism (except for sink and corner unit)•Hinge: SS Hinge Screw: SS 304.Shutter : should be of twin-type construction with sound dampening effect using profill. Shutter cover should be equipped with Bump on for sound dampening. Base Moulding should be made of PVC with corner clips. Ball Slide: 500mm Length Shutter should have provision of roller catch. PP Sink,Polypropylene Molded Sinks: Made up of 5 mm thick high density and elastic poly propylene with good resistance to organic solvents. Sink - Bowl size to be a minimum of (L x W x D) 560 x 355 x 300 mm. Faucet - 3-way type faucet as per approved make WORKTOP : Jet Black Granite: It should be 19mm (+/- 2mm) thick Jet Black Granite worktop. The exposed edges of the worktop should be chamfered and smoothened. The bottom of the worktop should be polished and there should be a V-groove throughout the length of the exposed edges to protect the cabinets from coming in contact with the spillages. The overhang on the storage cabinet is 25 mm at the front side and 30 mm at the sides. The backing material used is a neoprene mat of 6 mm thickness. as directed by Engineer In-charge(As per specified in Technical specification of furniture Page No.30 of NIT) |
| 37 | Providing supply installation of CORNER WALL TABLE - 11 WITH SINK (1115L x 1115D x 900mmH) WITH PEGBOARDconstruction: Floor based Welded cabinet system having storage body should be flush face construction with intersection of vertical and horizontal members like LH and RH side panel along with front horizontal channel, back panel and bottom panel. It should be relocated anywhere easily as it is an independent unit. Cabinet should of square non-sharp edge construction. Doors should be assembled with SS-304 hinge assembly. Removable back panel should be provided to easily access the service lines running behind the cabinet benches. Intermediate horizontal channels should be provided between door and drawer. Toe-space of 90mm X 90mm is provided at front-bottom side of cabinet. Levelers are provided for easy leveling of welded cabinet. Shelf should be eight-bend panel with 20mm height. Drawer tray should be of single piece construction. Drawer should be well supported on LH and RH ball slide suspension system. Steel door and drawer front should be of double wall construction with sound dampening material filled inside. Doors should be easily removable and hinges should be easily replaceable. Knee space panel should be in 22 gauge , Cabinets are tested as per SEFA 8M standard from a SEFA approved Lab and also tested as per EN 14727 from a third party testing agency having NABL accreditation.Dimensions: W= 750 mm, D = 750 mm, H = 875 mm Configurations: 1 Shutter - 1 Nos MOC: MSCRCA: IS – 513 (1994)•Thickness: LH/RH side panels, shutter front, Bottom panel, Top front, Drawer separator, shelf, Alignment channel is of 1.2mm thk. Removable Back panel, Shutter cover, Fr. Rack strip, Top cover panel is of 0.8mmthk • Finish: Powder coating pure epoxy, thickness 40-50 microns , followed with 9 tank Pretreatment process The thickness of powder coat should be 45-50 microns, which passes the test of Salt Spray for 1000 hours. It should have a high temperature withstanding capacity with excellent electrical insulation properties.The rear portion of above accessories which is in contact with live metal should be made from thermo set material which will not melt on heating.Handle: Anodized Aluminum Recessed-Type, CTC: 160.0mm Lock: Units have a locking facility with 180° and 10 lever cam lock mechanism (except for sink and corner unit)•Hinge: SS Hinge Screw: SS 304.Shutter : should be of twin-type construction with sound dampening effect using profill. Shutter cover should be equipped with Bump on for sound dampening. Base Moulding should be made of PVC with corner clips. Ball Slide: 500mm Length Shutter should have provision of roller catch. PP Sink,Polypropylene Molded Sinks: Made up of 5 mm thick high density and elastic poly propylene with good resistance to organic solvents. Sink - Bowl size to be a minimum of (L x W x D) 560 x 355 x 300 mm. Faucet - 3-way type faucet as per approved make PEGBOARD: SS Peg Board with 33 pp Pegs & Tray (Size: 600 mm x 600 mm x 15 mm)WORKTOP : Jet Black Granite: It should be 19mm (+/- 2mm) thick Jet Black Granite worktop. The exposed edges of the worktop should be chamfered and smoothened. The bottom of the worktop should be polished and there should be a V-groove throughout the length of the exposed edges to protect the cabinets from coming in contact with the spillages. The overhang on the storage cabinet is 25 mm at the front side and 30 mm at the sides. The backing material used is a neoprene mat of 6 mm thickness. as directed by Engineer In-charge(As per specified in Technical specification of furniture Page No.30 of NIT) |
| 38 | Providing supply installation of CORNER WALL TABLE - 16 WITH SINK (1265mmL x 1265mmD x 900mmH)construction: Floor based Welded cabinet system having storage body should be flush face construction with intersection of vertical and horizontal members like LH and RH side panel along with front horizontal channel, back panel and bottom panel. It should be relocated anywhere easily as it is an independent unit. Cabinet should of square non-sharp edge construction. Doors should be assembled with SS-304 hinge assembly. Removable back panel should be provided to easily access the service lines running behind the cabinet benches. Intermediate horizontal channels should be provided between door and drawer. Toe-space of 90mm X 90mm is provided at front-bottom side of cabinet. Levelers are provided for easy leveling of welded cabinet. Shelf should be eight-bend panel with 20mm height. Drawer tray should be of single piece construction. Drawer should be well supported on LH and RH ball slide suspension system. Steel door and drawer front should be of double wall construction with sound dampening material filled inside. Doors should be easily removable and hinges should be easily replaceable. Knee space panel should be in 22 gauge , Cabinets are tested as per SEFA 8M standard from a SEFA approved Lab and also tested as per EN 14727 from a third party testing agency having NABL accreditation.Dimensions: W= 750 mm, D = 750 mm, H = 875 mm Configurations: 1 Shutter - 1 Nos MOC: MSCRCA: IS – 513 (1994)•Thickness: LH/RH side panels, shutter front, Bottom panel, Top front, Drawer separator, shelf, Alignment channel is of 1.2mm thk. Removable Back panel, Shutter cover, Fr. Rack strip, Top cover panel is of 0.8mmthk • Finish: Powder coating pure epoxy, thickness 40-50 microns , followed with 9 tank Pretreatment process The thickness of powder coat should be 45-50 microns, which passes the test of Salt Spray for 1000 hours. It should have a high temperature withstanding capacity with excellent electrical insulation properties.The rear portion of above accessories which is in contact with live metal should be made from thermo set material which will not melt on heating.Handle: Anodized Aluminum Recessed-Type, CTC: 160.0mm Lock: Units have a locking facility with 180° and 10 lever cam lock mechanism (except for sink and corner unit)•Hinge: SS Hinge Screw: SS 304.Shutter : should be of twin-type construction with sound dampening effect using profill. Shutter cover should be equipped with Bump on for sound dampening. Base Moulding should be made of PVC with corner clips. Ball Slide: 500mm Length Shutter should have provision of roller catch. PP Sink,Polypropylene Molded Sinks: Made up of 5 mm thick high density and elastic poly propylene with good resistance to organic solvents. Sink - Bowl size to be a minimum of (L x W x D) 560 x 355 x 300 mm. Faucet - 3-way type faucet as per approved make WORKTOP : Jet Black Granite: It should be 19mm (+/- 2mm) thick Jet Black Granite worktop. The exposed edges of the worktop should be chamfered and smoothened. The bottom of the worktop should be polished and there should be a V-groove throughout the length of the exposed edges to protect the cabinets from coming in contact with the spillages. The overhang on the storage cabinet is 25 mm at the front side and 30 mm at the sides. The backing material used is a neoprene mat of 6 mm thickness. as directed by Engineer In-charge(As per specified in Technical specification of furniture Page No.30 of NIT) |
| 39 | Providing supply installation of CORNER WALL TABLE - 2 WITH SINK (1265L x 1265D x 900mmH)construction: Floor based Welded cabinet system having storage body should be flush face construction with intersection of vertical and horizontal members like LH and RH side panel along with front horizontal channel, back panel and bottom panel. It should be relocated anywhere easily as it is an independent unit. Cabinet should of square non-sharp edge construction. Doors should be assembled with SS-304 hinge assembly. Removable back panel should be provided to easily access the service lines running behind the cabinet benches. Intermediate horizontal channels should be provided between door and drawer. Toe-space of 90mm X 90mm is provided at front-bottom side of cabinet. Levelers are provided for easy leveling of welded cabinet. Shelf should be eight-bend panel with 20mm height. Drawer tray should be of single piece construction. Drawer should be well supported on LH and RH ball slide suspension system. Steel door and drawer front should be of double wall construction with sound dampening material filled inside. Doors should be easily removable and hinges should be easily replaceable. Knee space panel should be in 22 gauge , Cabinets are tested as per SEFA 8M standard from a SEFA approved Lab and also tested as per EN 14727 from a third party testing agency having NABL accreditation.Dimensions: W= 900 mm, D = 900 mm, H = 875 mm Configurations: 1 Shutter - 1 Nos MOC: MSCRCA: IS – 513 (1994)•Thickness: LH/RH side panels, shutter front, Bottom panel, Top front, Drawer separator, shelf, Alignment channel is of 1.2mm thk. Removable Back panel, Shutter cover, Fr. Rack strip, Top cover panel is of 0.8mmthk • Finish: Powder coating pure epoxy, thickness 40-50 microns , followed with 9 tank Pretreatment process The thickness of powder coat should be 45-50 microns, which passes the test of Salt Spray for 1000 hours. It should have a high temperature withstanding capacity with excellent electrical insulation properties.The rear portion of above accessories which is in contact with live metal should be made from thermo set material which will not melt on heating.Handle: Anodized Aluminum Recessed-Type, CTC: 160.0mm Lock: Units have a locking facility with 180° and 10 lever cam lock mechanism (except for sink and corner unit)•Hinge: SS Hinge Screw: SS 304.Shutter : should be of twin-type construction with sound dampening effect using profill. Shutter cover should be equipped with Bump on for sound dampening. Base Moulding should be made of PVC with corner clips. Ball Slide: 500mm Length Shutter should have provision of roller catch. PP Sink,Polypropylene Molded Sinks: Made up of 5 mm thick high density and elastic poly propylene with good resistance to organic solvents. Sink - Bowl size to be a minimum of (L x W x D) 560 x 355 x 300 mm. Faucet - 3-way type faucet as per approved make WORKTOP : Jet Black Granite: It should be 19mm (+/- 2mm) thick Jet Black Granite worktop. The exposed edges of the worktop should be chamfered and smoothened. The bottom of the worktop should be polished and there should be a V-groove throughout the length of the exposed edges to protect the cabinets from coming in contact with the spillages. The overhang on the storage cabinet is 25 mm at the front side and 30 mm at the sides. The backing material used is a neoprene mat of 6 mm thickness.PEGBOARD: SS Peg Board with 33 pp Pegs & Tray (Size: 600 mm x 600 mm x 15 mm) as directed by Engineer In-charge(As per specified in Technical specification of furniture Page No.30 of NIT) |
| 40 | Providing supply installation of CORNER WALL TABLE - 2 WITH SINK (1115L x 1115D x 900mmH)construction: Floor based Welded cabinet system having storage body should be flush face construction with intersection of vertical and horizontal members like LH and RH side panel along with front horizontal channel, back panel and bottom panel. It should be relocated anywhere easily as it is an independent unit. Cabinet should of square non-sharp edge construction. Doors should be assembled with SS-304 hinge assembly. Removable back panel should be provided to easily access the service lines running behind the cabinet benches. Intermediate horizontal channels should be provided between door and drawer. Toe-space of 90mm X 90mm is provided at front-bottom side of cabinet. Levelers are provided for easy leveling of welded cabinet. Shelf should be eight-bend panel with 20mm height. Drawer tray should be of single piece construction. Drawer should be well supported on LH and RH ball slide suspension system. Steel door and drawer front should be of double wall construction with sound dampening material filled inside. Doors should be easily removable and hinges should be easily replaceable. Knee space panel should be in 22 gauge , Cabinets are tested as per SEFA 8M standard from a SEFA approved Lab and also tested as per EN 14727 from a third party testing agency having NABL accreditation.Dimensions: W= 900 mm, D = 900 mm, H = 875 mm Configurations: 1 Shutter - 1 Nos MOC: MSCRCA: IS – 513 (1994)•Thickness: LH/RH side panels, shutter front, Bottom panel, Top front, Drawer separator, shelf, Alignment channel is of 1.2mm thk. Removable Back panel, Shutter cover, Fr. Rack strip, Top cover panel is of 0.8mmthk • Finish: Powder coating pure epoxy, thickness 40-50 microns , followed with 9 tank Pretreatment process The thickness of powder coat should be 45-50 microns, which passes the test of Salt Spray for 1000 hours. It should have a high temperature withstanding capacity with excellent electrical insulation properties.The rear portion of above accessories which is in contact with live metal should be made from thermo set material which will not melt on heating.Handle: Anodized Aluminum Recessed-Type, CTC: 160.0mm Lock: Units have a locking facility with 180° and 10 lever cam lock mechanism (except for sink and corner unit)•Hinge: SS Hinge Screw: SS 304.Shutter : should be of twin-type construction with sound dampening effect using profill. Shutter cover should be equipped with Bump on for sound dampening. Base Moulding should be made of PVC with corner clips. Ball Slide: 500mm Length Shutter should have provision of roller catch. PP Sink,Polypropylene Molded Sinks: Made up of 5 mm thick high density and elastic poly propylene with good resistance to organic solvents. Sink - Bowl size to be a minimum of (L x W x D) 560 x 355 x 300 mm. Faucet - 3-way type faucet as per approved make WORKTOP : Jet Black Granite: It should be 19mm (+/- 2mm) thick Jet Black Granite worktop. The exposed edges of the worktop should be chamfered and smoothened. The bottom of the worktop should be polished and there should be a V-groove throughout the length of the exposed edges to protect the cabinets from coming in contact with the spillages. The overhang on the storage cabinet is 25 mm at the front side and 30 mm at the sides. The backing material used is a neoprene mat of 6 mm thickness. as directed by Engineer In-charge(As per specified in Technical specification of furniture Page No.30 of NIT) |
| 41 | Providing supply installation of CORNER WALL TABLE - 2 WITH SINK (1115L x 1115D x 900mmH) WITH PEGBOARDconstruction: Floor based Welded cabinet system having storage body should be flush face construction with intersection of vertical and horizontal members like LH and RH side panel along with front horizontal channel, back panel and bottom panel. It should be relocated anywhere easily as it is an independent unit. Cabinet should of square non-sharp edge construction. Doors should be assembled with SS-304 hinge assembly. Removable back panel should be provided to easily access the service lines running behind the cabinet benches. Intermediate horizontal channels should be provided between door and drawer. Toe-space of 90mm X 90mm is provided at front-bottom side of cabinet. Levelers are provided for easy leveling of welded cabinet. Shelf should be eight-bend panel with 20mm height. Drawer tray should be of single piece construction. Drawer should be well supported on LH and RH ball slide suspension system. Steel door and drawer front should be of double wall construction with sound dampening material filled inside. Doors should be easily removable and hinges should be easily replaceable. Knee space panel should be in 22 gauge , Cabinets are tested as per SEFA 8M standard from a SEFA approved Lab and also tested as per EN 14727 from a third party testing agency having NABL accreditation.Dimensions: W= 750 mm, D = 750 mm, H = 875 mm Configurations: 1 Shutter - 1 Nos MOC: MSCRCA: IS – 513 (1994)•Thickness: LH/RH side panels, shutter front, Bottom panel, Top front, Drawer separator, shelf, Alignment channel is of 1.2mm thk. Removable Back panel, Shutter cover, Fr. Rack strip, Top cover panel is of 0.8mmthk • Finish: Powder coating pure epoxy, thickness 40-50 microns , followed with 9 tank Pretreatment process The thickness of powder coat should be 45-50 microns, which passes the test of Salt Spray for 1000 hours. It should have a high temperature withstanding capacity with excellent electrical insulation properties.The rear portion of above accessories which is in contact with live metal should be made from thermo set material which will not melt on heating.Handle: Anodized Aluminum Recessed-Type, CTC: 160.0mm Lock: Units have a locking facility with 180° and 10 lever cam lock mechanism (except for sink and corner unit)•Hinge: SS Hinge Screw: SS 304.Shutter : should be of twin-type construction with sound dampening effect using profill. Shutter cover should be equipped with Bump on for sound dampening. Base Moulding should be made of PVC with corner clips. Ball Slide: 500mm Length Shutter should have provision of roller catch. PP Sink,Polypropylene Molded Sinks: Made up of 5 mm thick high density and elastic poly propylene with good resistance to organic solvents. Sink - Bowl size to be a minimum of (L x W x D) 560 x 355 x 300 mm. Faucet - 3-way type faucet as per approved make PEGBOARD: SS Peg Board with 33 pp Pegs & Tray (Size: 600 mm x 600 mm x 15 mm)WORKTOP : Jet Black Granite: It should be 19mm (+/- 2mm) thick Jet Black Granite worktop. The exposed edges of the worktop should be chamfered and smoothened. The bottom of the worktop should be polished and there should be a V-groove throughout the length of the exposed edges to protect the cabinets from coming in contact with the spillages. The overhang on the storage cabinet is 25 mm at the front side and 30 mm at the sides. The backing material used is a neoprene mat of 6 mm thickness. as directed by Engineer In-charge(As per specified in Technical specification of furniture Page No.30 of NIT) |
| 42 | Providing supply installation of CORNER WALL TABLE - 11 WITH SINK (1115L x 1115D x 900mmH) WITH PEGBOARDconstruction: Floor based Welded cabinet system having storage body should be flush face construction with intersection of vertical and horizontal members like LH and RH side panel along with front horizontal channel, back panel and bottom panel. It should be relocated anywhere easily as it is an independent unit. Cabinet should of square non-sharp edge construction. Doors should be assembled with SS-304 hinge assembly. Removable back panel should be provided to easily access the service lines running behind the cabinet benches. Intermediate horizontal channels should be provided between door and drawer. Toe-space of 90mm X 90mm is provided at front-bottom side of cabinet. Levelers are provided for easy leveling of welded cabinet. Shelf should be eight-bend panel with 20mm height. Drawer tray should be of single piece construction. Drawer should be well supported on LH and RH ball slide suspension system. Steel door and drawer front should be of double wall construction with sound dampening material filled inside. Doors should be easily removable and hinges should be easily replaceable. Knee space panel should be in 22 gauge , Cabinets are tested as per SEFA 8M standard from a SEFA approved Lab and also tested as per EN 14727 from a third party testing agency having NABL accreditation.Dimensions: W= 750 mm, D = 750 mm, H = 875 mm Configurations: 1 Shutter - 1 Nos MOC: MSCRCA: IS – 513 (1994)•Thickness: LH/RH side panels, shutter front, Bottom panel, Top front, Drawer separator, shelf, Alignment channel is of 1.2mm thk. Removable Back panel, Shutter cover, Fr. Rack strip, Top cover panel is of 0.8mmthk • Finish: Powder coating pure epoxy, thickness 40-50 microns , followed with 9 tank Pretreatment process The thickness of powder coat should be 45-50 microns, which passes the test of Salt Spray for 1000 hours. It should have a high temperature withstanding capacity with excellent electrical insulation properties.The rear portion of above accessories which is in contact with live metal should be made from thermo set material which will not melt on heating.Handle: Anodized Aluminum Recessed-Type, CTC: 160.0mm Lock: Units have a locking facility with 180° and 10 lever cam lock mechanism (except for sink and corner unit)•Hinge: SS Hinge Screw: SS 304.Shutter : should be of twin-type construction with sound dampening effect using profill. Shutter cover should be equipped with Bump on for sound dampening. Base Moulding should be made of PVC with corner clips. Ball Slide: 500mm Length Shutter should have provision of roller catch. PP Sink,Polypropylene Molded Sinks: Made up of 5 mm thick high density and elastic poly propylene with good resistance to organic solvents. Sink - Bowl size to be a minimum of (L x W x D) 560 x 355 x 300 mm. Faucet - 3-way type faucet as per approved make PEGBOARD: SS Peg Board with 33 pp Pegs & Tray (Size: 600 mm x 600 mm x 15 mm)WORKTOP : Jet Black Granite: It should be 19mm (+/- 2mm) thick Jet Black Granite worktop. The exposed edges of the worktop should be chamfered and smoothened. The bottom of the worktop should be polished and there should be a V-groove throughout the length of the exposed edges to protect the cabinets from coming in contact with the spillages. The overhang on the storage cabinet is 25 mm at the front side and 30 mm at the sides. The backing material used is a neoprene mat of 6 mm thickness. as directed by Engineer In-charge(As per specified in Technical specification of furniture Page No.30 of NIT) |
| 43 | Providing supply installation of CORNER WALL TABLE - 2 WITH SINK (1265L x 1265D x 900mmH)construction: Floor based Welded cabinet system having storage body should be flush face construction with intersection of vertical and horizontal members like LH and RH side panel along with front horizontal channel, back panel and bottom panel. It should be relocated anywhere easily as it is an independent unit. Cabinet should of square non-sharp edge construction. Doors should be assembled with SS-304 hinge assembly. Removable back panel should be provided to easily access the service lines running behind the cabinet benches. Intermediate horizontal channels should be provided between door and drawer. Toe-space of 90mm X 90mm is provided at front-bottom side of cabinet. Levelers are provided for easy leveling of welded cabinet. Shelf should be eight-bend panel with 20mm height. Drawer tray should be of single piece construction. Drawer should be well supported on LH and RH ball slide suspension system. Steel door and drawer front should be of double wall construction with sound dampening material filled inside. Doors should be easily removable and hinges should be easily replaceable. Knee space panel should be in 22 gauge , Cabinets are tested as per SEFA 8M standard from a SEFA approved Lab and also tested as per EN 14727 from a third party testing agency having NABL accreditation.Dimensions: W= 900 mm, D = 900 mm, H = 875 mm Configurations: 1 Shutter - 1 Nos MOC: MSCRCA: IS – 513 (1994)•Thickness: LH/RH side panels, shutter front, Bottom panel, Top front, Drawer separator, shelf, Alignment channel is of 1.2mm thk. Removable Back panel, Shutter cover, Fr. Rack strip, Top cover panel is of 0.8mmthk • Finish: Powder coating pure epoxy, thickness 40-50 microns , followed with 9 tank Pretreatment process The thickness of powder coat should be 45-50 microns, which passes the test of Salt Spray for 1000 hours. It should have a high temperature withstanding capacity with excellent electrical insulation properties.The rear portion of above accessories which is in contact with live metal should be made from thermo set material which will not melt on heating.Handle: Anodized Aluminum Recessed-Type, CTC: 160.0mm Lock: Units have a locking facility with 180° and 10 lever cam lock mechanism (except for sink and corner unit)•Hinge: SS Hinge Screw: SS 304.Shutter : should be of twin-type construction with sound dampening effect using profill. Shutter cover should be equipped with Bump on for sound dampening. Base Moulding should be made of PVC with corner clips. Ball Slide: 500mm Length Shutter should have provision of roller catch. PP Sink,Polypropylene Molded Sinks: Made up of 5 mm thick high density and elastic poly propylene with good resistance to organic solvents. Sink - Bowl size to be a minimum of (L x W x D) 560 x 355 x 300 mm. Faucet - 3-way type faucet as per approved make WORKTOP : Jet Black Granite: It should be 19mm (+/- 2mm) thick Jet Black Granite worktop. The exposed edges of the worktop should be chamfered and smoothened. The bottom of the worktop should be polished and there should be a V-groove throughout the length of the exposed edges to protect the cabinets from coming in contact with the spillages. The overhang on the storage cabinet is 25 mm at the front side and 30 mm at the sides. The backing material used is a neoprene mat of 6 mm thickness. as directed by Engineer In-charge(As per specified in Technical specification of furniture Page No.30 of NIT) |
| 44 | Providing supply installation of CORNER WALL TABLE - 2 WITH SINK(1265L x 1265D x 900mmH) construction: Floor based Welded cabinet system having storage body should be flush face construction with intersection of vertical and horizontal members like LH and RH side panel along with front horizontal channel, back panel and bottom panel. It should be relocated anywhere easily as it is an independent unit. Cabinet should of square non-sharp edge construction. Doors should be assembled with SS-304 hinge assembly. Removable back panel should be provided to easily access the service lines running behind the cabinet benches. Intermediate horizontal channels should be provided between door and drawer. Toe-space of 90mm X 90mm is provided at front-bottom side of cabinet. Levelers are provided for easy leveling of welded cabinet. Shelf should be eight-bend panel with 20mm height. Drawer tray should be of single piece construction. Drawer should be well supported on LH and RH ball slide suspension system. Steel door and drawer front should be of double wall construction with sound dampening material filled inside. Doors should be easily removable and hinges should be easily replaceable. Knee space panel should be in 22 gauge , Cabinets are tested as per SEFA 8M standard from a SEFA approved Lab and also tested as per EN 14727 from a third party testing agency having NABL accreditation.Dimensions: W= 900 mm, D = 900 mm, H = 875 mm Configurations: 1 Shutter - 1 Nos MOC: MSCRCA: IS – 513 (1994)•Thickness: LH/RH side panels, shutter front, Bottom panel, Top front, Drawer separator, shelf, Alignment channel is of 1.2mm thk. Removable Back panel, Shutter cover, Fr. Rack strip, Top cover panel is of 0.8mmthk • Finish: Powder coating pure epoxy, thickness 40-50 microns , followed with 9 tank Pretreatment process The thickness of powder coat should be 45-50 microns, which passes the test of Salt Spray for 1000 hours. It should have a high temperature withstanding capacity with excellent electrical insulation properties.The rear portion of above accessories which is in contact with live metal should be made from thermo set material which will not melt on heating.Handle: Anodized Aluminum Recessed-Type, CTC: 160.0mm Lock: Units have a locking facility with 180° and 10 lever cam lock mechanism (except for sink and corner unit)•Hinge: SS Hinge Screw: SS 304.Shutter : should be of twin-type construction with sound dampening effect using profill. Shutter cover should be equipped with Bump on for sound dampening. Base Moulding should be made of PVC with corner clips. Ball Slide: 500mm Length Shutter should have provision of roller catch. WORKTOP : Jet Black Granite: It should be 19mm (+/- 2mm) thick Jet Black Granite worktop. The exposed edges of the worktop should be chamfered and smoothened. The bottom of the worktop should be polished and there should be a V-groove throughout the length of the exposed edges to protect the cabinets from coming in contact with the spillages. The overhang on the storage cabinet is 25 mm at the front side and 30 mm at the sides. The backing material used is a neoprene mat of 6 mm thickness. as directed by Engineer In-charge(As per specified in Technical specification of furniture Page No.30 of NIT) |
| 45 | Providing supply installation of CORNER WALL TABLE - 11 WITH SINK (1115L x 1115D x 900mmH) construction: Floor based Welded cabinet system having storage body should be flush face construction with intersection of vertical and horizontal members like LH and RH side panel along with front horizontal channel, back panel and bottom panel. It should be relocated anywhere easily as it is an independent unit. Cabinet should of square non-sharp edge construction. Doors should be assembled with SS-304 hinge assembly. Removable back panel should be provided to easily access the service lines running behind the cabinet benches. Intermediate horizontal channels should be provided between door and drawer. Toe-space of 90mm X 90mm is provided at front-bottom side of cabinet. Levelers are provided for easy leveling of welded cabinet. Shelf should be eight-bend panel with 20mm height. Drawer tray should be of single piece construction. Drawer should be well supported on LH and RH ball slide suspension system. Steel door and drawer front should be of double wall construction with sound dampening material filled inside. Doors should be easily removable and hinges should be easily replaceable. Knee space panel should be in 22 gauge , Cabinets are tested as per SEFA 8M standard from a SEFA approved Lab and also tested as per EN 14727 from a third party testing agency having NABL accreditation.Dimensions: W= 750 mm, D = 750 mm, H = 875 mm Configurations: 1 Shutter - 1 Nos MOC: MSCRCA: IS – 513 (1994)•Thickness: LH/RH side panels, shutter front, Bottom panel, Top front, Drawer separator, shelf, Alignment channel is of 1.2mm thk. Removable Back panel, Shutter cover, Fr. Rack strip, Top cover panel is of 0.8mmthk • Finish: Powder coating pure epoxy, thickness 40-50 microns , followed with 9 tank Pretreatment process The thickness of powder coat should be 45-50 microns, which passes the test of Salt Spray for 1000 hours. It should have a high temperature withstanding capacity with excellent electrical insulation properties.The rear portion of above accessories which is in contact with live metal should be made from thermo set material which will not melt on heating.Handle: Anodized Aluminum Recessed-Type, CTC: 160.0mm Lock: Units have a locking facility with 180° and 10 lever cam lock mechanism (except for sink and corner unit)•Hinge: SS Hinge Screw: SS 304.Shutter : should be of twin-type construction with sound dampening effect using profill. Shutter cover should be equipped with Bump on for sound dampening. Base Moulding should be made of PVC with corner clips. Ball Slide: 500mm Length Shutter should have provision of roller catch. PP Sink,Polypropylene Molded Sinks: Made up of 5 mm thick high density and elastic poly propylene with good resistance to organic solvents. Sink - Bowl size to be a minimum of (L x W x D) 560 x 355 x 300 mm. Faucet - 3-way type faucet as per approved make WORKTOP : Jet Black Granite: It should be 19mm (+/- 2mm) thick Jet Black Granite worktop. The exposed edges of the worktop should be chamfered and smoothened. The bottom of the worktop should be polished and there should be a V-groove throughout the length of the exposed edges to protect the cabinets from coming in contact with the spillages. The overhang on the storage cabinet is 25 mm at the front side and 30 mm at the sides. The backing material used is a neoprene mat of 6 mm thickness. as directed by Engineer In-charge(As per specified in Technical specification of furniture Page No.30 of NIT) |
| 46 | Providing supply installation of FREE STANDING WALL TABLE - 6 1580mmL X 820mmD X 750mmHConstruction : Floor based Welded cabinet system having storage body should be flush face construction with intersection of vertical and horizontal members like LH and RH side panel along with front horizontal channel, back panel and bottom panel. It should be relocated anywhere easily as it is an independent unit. Cabinet should of square non-sharp edge construction. Doors should be assembled with SS-304 hinge assembly. Removable back panel should be provided to easily access the service lines running behind the cabinet benches. Intermediate horizontal channels should be provided between door and drawer. Toe-space of 90mm X 90mm is provided at front-bottom side of cabinet. Levelers are provided for easy leveling of welded cabinet. Shelf should be eight-bend panel with 20mm height. Drawer tray should be of single piece construction. Drawer should be well supported on LH and RH ball slide suspension system. Steel door and drawer front should be of double wall construction with sound dampening material filled inside. Doors should be easily removable and hinges should be easily replaceable. Knee space panel should be in 22 gauge construction. Cabinets are tested as per SEFA 8M standard from a SEFA approved Lab and also tested as per EN 14727 from a third party testing agencyDimensions: W=450 mm, D = 530mm, H = 875 mm Configurations: Storage - 450 W 1 Drawer + 1 Shutter - 2 Nos , Midle legspace 600 W - 1 NosMOC: MSCRCA: IS – 513 (1994)Thickness: LH/RH side panels, shutter front, Bottom panel, Top front, Drawer separator, shelf, Alignment channel is of 1.2mm thk. Removable Back panel, Shutter cover, Fr. Rack strip, Top cover panel is of 0.8mmthk Finish: The complete M.S. material of cabinet should be pre-treated (degreased, Zinc phosphated) and epoxy powder coated for better corrosion resistance. The thickness of powder coat should be 45-50 microns, which passes the test of Salt Spray for 1000 hours. It should have a high temperature withstanding capacity with excellent electrical insulation properties.The rear portion of above accessories which is in contact with live metal should be made from thermo set material which will not melt on heating.Handle: Anodized Aluminum Recessed-Type, CTC: 160.0mm Lock: Units have a locking facility with 180° and 10 lever cam lock mechanism (except for sink and corner unit)Hinge: SS Hinge .Screw: SS 304.Shutter : should be of twin-type construction with sound dampening effect using profill. Shutter cover should be equipped with Bump on for sound dampening. Base Moulding should be made of PVC with corner clips. Ball Slide: 500mm Length Shutter should have provision of roller catch. COVER / FILLER PANELS All side cover panels and back panels, filler panels should be made from CRCA MS panels of 1.0mm thickness with pure epoxy powder coating . SERVICE FITTINGS AND ACCESSORIES Service fittings should be laboratory grade, and water faucets and valve bodies should be cast red brass alloy or bronze forgings, all fittings should be powder plated unless specified otherwise. Service Indexes: Fittings should be identified with service indexes in the color coding as per DIN 12920.WORKTOP : Jet Black Granite: It should be 19mm (+/- 2mm) thick Jet Black Granite worktop. The exposed edges of the worktop should be chamfered and smoothened. The bottom of the worktop should be polished and there should be a V-groove throughout the length of the exposed edges to protect the cabinets from coming in contact with the spillages. The overhang on the storage cabinet is 25 mm at the front side and 30 mm at the sides. The backing material used is a neoprene mat of 6 mm thickness. as directed by Engineer In-charge(As per specified in Technical specification of furniture Page No.30 of NIT) |
| 47 | Providing supply installation of FREE STANDING WALL TABLE - 6 1580mmL X 820mmD X 750mmHConstruction : Floor based Welded cabinet system having storage body should be flush face construction with intersection of vertical and horizontal members like LH and RH side panel along with front horizontal channel, back panel and bottom panel. It should be relocated anywhere easily as it is an independent unit. Cabinet should of square non-sharp edge construction. Doors should be assembled with SS-304 hinge assembly. Removable back panel should be provided to easily access the service lines running behind the cabinet benches. Intermediate horizontal channels should be provided between door and drawer. Toe-space of 90mm X 90mm is provided at front-bottom side of cabinet. Levelers are provided for easy leveling of welded cabinet. Shelf should be eight-bend panel with 20mm height. Drawer tray should be of single piece construction. Drawer should be well supported on LH and RH ball slide suspension system. Steel door and drawer front should be of double wall construction with sound dampening material filled inside. Doors should be easily removable and hinges should be easily replaceable. Knee space panel should be in 22 gauge construction. Cabinets are tested as per SEFA 8M standard from a SEFA approved Lab and also tested as per EN 14727 from a third party testing agencyDimensions: W=450 mm, D = 530mm, H = 875 mm Configurations: Storage - 450 W 1 Drawer + 1 Shutter - 2 Nos , Midle legspace 600 W - 1 NosMOC: MSCRCA: IS – 513 (1994)Thickness: LH/RH side panels, shutter front, Bottom panel, Top front, Drawer separator, shelf, Alignment channel is of 1.2mm thk. Removable Back panel, Shutter cover, Fr. Rack strip, Top cover panel is of 0.8mmthk Finish: The complete M.S. material of cabinet should be pre-treated (degreased, Zinc phosphated) and epoxy powder coated for better corrosion resistance. The thickness of powder coat should be 45-50 microns, which passes the test of Salt Spray for 1000 hours. It should have a high temperature withstanding capacity with excellent electrical insulation properties.The rear portion of above accessories which is in contact with live metal should be made from thermo set material which will not melt on heating.Handle: Anodized Aluminum Recessed-Type, CTC: 160.0mm Lock: Units have a locking facility with 180° and 10 lever cam lock mechanism (except for sink and corner unit)Hinge: SS Hinge .Screw: SS 304.Shutter : should be of twin-type construction with sound dampening effect using profill. Shutter cover should be equipped with Bump on for sound dampening. Base Moulding should be made of PVC with corner clips. Ball Slide: 500mm Length Shutter should have provision of roller catch. COVER / FILLER PANELS All side cover panels and back panels, filler panels should be made from CRCA MS panels of 1.0mm thickness with pure epoxy powder coating . SERVICE FITTINGS AND ACCESSORIES Service fittings should be laboratory grade, and water faucets and valve bodies should be cast red brass alloy or bronze forgings, all fittings should be powder plated unless specified otherwise. Service Indexes: Fittings should be identified with service indexes in the color coding as per DIN 12920.WORKTOP : Jet Black Granite: It should be 19mm (+/- 2mm) thick Jet Black Granite worktop. The exposed edges of the worktop should be chamfered and smoothened. The bottom of the worktop should be polished and there should be a V-groove throughout the length of the exposed edges to protect the cabinets from coming in contact with the spillages. The overhang on the storage cabinet is 25 mm at the front side and 30 mm at the sides. The backing material used is a neoprene mat of 6 mm thickness. as directed by Engineer In-charge(As per specified in Technical specification of furniture Page No.30 of NIT) |
| 48 | Providing supply installation of FREE STANDING WALL TABLE - 6 1580mmL X 820mmD X 750mmHConstruction : Floor based Welded cabinet system having storage body should be flush face construction with intersection of vertical and horizontal members like LH and RH side panel along with front horizontal channel, back panel and bottom panel. It should be relocated anywhere easily as it is an independent unit. Cabinet should of square non-sharp edge construction. Doors should be assembled with SS-304 hinge assembly. Removable back panel should be provided to easily access the service lines running behind the cabinet benches. Intermediate horizontal channels should be provided between door and drawer. Toe-space of 90mm X 90mm is provided at front-bottom side of cabinet. Levelers are provided for easy leveling of welded cabinet. Shelf should be eight-bend panel with 20mm height. Drawer tray should be of single piece construction. Drawer should be well supported on LH and RH ball slide suspension system. Steel door and drawer front should be of double wall construction with sound dampening material filled inside. Doors should be easily removable and hinges should be easily replaceable. Knee space panel should be in 22 gauge construction. Cabinets are tested as per SEFA 8M standard from a SEFA approved Lab and also tested as per EN 14727 from a third party testing agencyDimensions: W=450 mm, D = 530mm, H = 875 mm Configurations: Storage - 450 W 1 Drawer + 1 Shutter - 2 Nos , Midle legspace 600 W - 1 NosMOC: MSCRCA: IS – 513 (1994)Thickness: LH/RH side panels, shutter front, Bottom panel, Top front, Drawer separator, shelf, Alignment channel is of 1.2mm thk. Removable Back panel, Shutter cover, Fr. Rack strip, Top cover panel is of 0.8mmthk Finish: The complete M.S. material of cabinet should be pre-treated (degreased, Zinc phosphated) and epoxy powder coated for better corrosion resistance. The thickness of powder coat should be 45-50 microns, which passes the test of Salt Spray for 1000 hours. It should have a high temperature withstanding capacity with excellent electrical insulation properties.The rear portion of above accessories which is in contact with live metal should be made from thermo set material which will not melt on heating.Handle: Anodized Aluminum Recessed-Type, CTC: 160.0mm Lock: Units have a locking facility with 180° and 10 lever cam lock mechanism (except for sink and corner unit)Hinge: SS Hinge .Screw: SS 304.Shutter : should be of twin-type construction with sound dampening effect using profill. Shutter cover should be equipped with Bump on for sound dampening. Base Moulding should be made of PVC with corner clips. Ball Slide: 500mm Length Shutter should have provision of roller catch. COVER / FILLER PANELS All side cover panels and back panels, filler panels should be made from CRCA MS panels of 1.0mm thickness with pure epoxy powder coating . SERVICE FITTINGS AND ACCESSORIES Service fittings should be laboratory grade, and water faucets and valve bodies should be cast red brass alloy or bronze forgings, all fittings should be powder plated unless specified otherwise. Service Indexes: Fittings should be identified with service indexes in the color coding as per DIN 12920.WORKTOP : Jet Black Granite: It should be 19mm (+/- 2mm) thick Jet Black Granite worktop. The exposed edges of the worktop should be chamfered and smoothened. The bottom of the worktop should be polished and there should be a V-groove throughout the length of the exposed edges to protect the cabinets from coming in contact with the spillages. The overhang on the storage cabinet is 25 mm at the front side and 30 mm at the sides. The backing material used is a neoprene mat of 6 mm thickness. as directed by Engineer In-charge(As per specified in Technical specification of furniture Page No.30 of NIT) |
| 49 | Providing supply installation of FREE STANDING WALL TABLE - 6 1580mmL X 820mmD X 750mmHConstruction : Floor based Welded cabinet system having storage body should be flush face construction with intersection of vertical and horizontal members like LH and RH side panel along with front horizontal channel, back panel and bottom panel. It should be relocated anywhere easily as it is an independent unit. Cabinet should of square non-sharp edge construction. Doors should be assembled with SS-304 hinge assembly. Removable back panel should be provided to easily access the service lines running behind the cabinet benches. Intermediate horizontal channels should be provided between door and drawer. Toe-space of 90mm X 90mm is provided at front-bottom side of cabinet. Levelers are provided for easy leveling of welded cabinet. Shelf should be eight-bend panel with 20mm height. Drawer tray should be of single piece construction. Drawer should be well supported on LH and RH ball slide suspension system. Steel door and drawer front should be of double wall construction with sound dampening material filled inside. Doors should be easily removable and hinges should be easily replaceable. Knee space panel should be in 22 gauge construction. Cabinets are tested as per SEFA 8M standard from a SEFA approved Lab and also tested as per EN 14727 from a third party testing agencyDimensions: W=450 mm, D = 530mm, H = 875 mm Configurations: Storage - 450 W 1 Drawer + 1 Shutter - 2 Nos , Midle legspace 600 W - 1 NosMOC: MSCRCA: IS – 513 (1994)Thickness: LH/RH side panels, shutter front, Bottom panel, Top front, Drawer separator, shelf, Alignment channel is of 1.2mm thk. Removable Back panel, Shutter cover, Fr. Rack strip, Top cover panel is of 0.8mmthk Finish: The complete M.S. material of cabinet should be pre-treated (degreased, Zinc phosphated) and epoxy powder coated for better corrosion resistance. The thickness of powder coat should be 45-50 microns, which passes the test of Salt Spray for 1000 hours. It should have a high temperature withstanding capacity with excellent electrical insulation properties.The rear portion of above accessories which is in contact with live metal should be made from thermo set material which will not melt on heating.Handle: Anodized Aluminum Recessed-Type, CTC: 160.0mm Lock: Units have a locking facility with 180° and 10 lever cam lock mechanism (except for sink and corner unit)Hinge: SS Hinge .Screw: SS 304.Shutter : should be of twin-type construction with sound dampening effect using profill. Shutter cover should be equipped with Bump on for sound dampening. Base Moulding should be made of PVC with corner clips. Ball Slide: 500mm Length Shutter should have provision of roller catch. COVER / FILLER PANELS All side cover panels and back panels, filler panels should be made from CRCA MS panels of 1.0mm thickness with pure epoxy powder coating . SERVICE FITTINGS AND ACCESSORIES Service fittings should be laboratory grade, and water faucets and valve bodies should be cast red brass alloy or bronze forgings, all fittings should be powder plated unless specified otherwise. Service Indexes: Fittings should be identified with service indexes in the color coding as per DIN 12920.WORKTOP : Jet Black Granite: It should be 19mm (+/- 2mm) thick Jet Black Granite worktop. The exposed edges of the worktop should be chamfered and smoothened. The bottom of the worktop should be polished and there should be a V-groove throughout the length of the exposed edges to protect the cabinets from coming in contact with the spillages. The overhang on the storage cabinet is 25 mm at the front side and 30 mm at the sides. The backing material used is a neoprene mat of 6 mm thickness. as directed by Engineer In-charge(As per specified in Technical specification of furniture Page No.30 of NIT) |
| 50 | Providing supply installation of ISLAND TABLE - 10 3380mmL X 1540mmD X 900mmH WITH ELECTRICAL TRUNKINGConstruction : Floor based Welded cabinet system having storage body should be flush face construction with intersection of vertical and horizontal members like LH and RH side panel along with front horizontal channel, back panel and bottom panel. It should be relocated anywhere easily as it is an independent unit. Cabinet should of square non-sharp edge construction. Doors should be assembled with SS-304 hinge assembly. Removable back panel should be provided to easily access the service lines running behind the cabinet benches. Intermediate horizontal channels should be provided between door and drawer. Toe-space of 90mm X 90mm is provided at front-bottom side of cabinet. Levelers are provided for easy leveling of welded cabinet. Shelf should be eight-bend panel with 20mm height. Drawer tray should be of single piece construction. Drawer should be well supported on LH and RH ball slide suspension system. Steel door and drawer front should be of double wall construction with sound dampening material filled inside. Doors should be easily removable and hinges should be easily replaceable. Knee space panel should be in 22 gauge construction. Cabinets are tested as per SEFA 8M standard from a SEFA approved Lab and also tested as per EN 14727 from a third party testing agencyDimensions: W=600 mm, 750 mm, 900mm , D = 530mm, H = 875 mm Configurations: continuous storages MOC: MSCRCA: IS – 513 (1994) Thickness: LH/RH side panels, shutter front, Bottom panel, Top front, Drawer separator, shelf, Alignment channel is of 1.2mm thk. Removable Back panel, Shutter cover, Fr. Rack strip, Top cover panel is of 0.8mmthk Finish: The complete M.S. material of cabinet should be pre-treated (degreased, Zinc phosphated) and epoxy powder coated for better corrosion resistance. The thickness of powder coat should be 45-50 microns, which passes the test of Salt Spray for 1000 hours. It should have a high temperature withstanding capacity with excellent electrical insulation properties.The rear portion of above accessories which is in contact with live metal should be made from thermo set material which will not melt on heating.Handle: Anodized Aluminum Recessed-Type, CTC: 160.0mm Lock: Units have a locking facility with 180° and 10 lever cam lock mechanism (except for sink and corner unit) Hinge: SS Hinge .Screw: SS 304.Shutter : should be of twin-type construction with sound dampening effect using profill. Shutter cover should be equipped with Bump on for sound dampening. Base Moulding should be made of PVC with corner clips. Ball Slide: 500mm Length Shutter should have provision of roller catch. COVER / FILLER PANELS All side cover panels and back panels, filler panels should be made from CRCA MS panels of 1.0mm thickness with pure epoxy powder coating . SERVICE FITTINGS AND ACCESSORIES Service fittings should be laboratory grade, and water faucets and valve bodies should be cast red brass alloy or bronze forgings, all fittings should be powder plated unless specified otherwise. Service Indexes: Fittings should be identified with service indexes in the color coding as per DIN 12920. ELECTRICAL ACCESSORIES (6/16 A SWITCHES & SOCKETS) : These are made of High gloss virgin grade engineering thermoplastics to impart a defect free surface. they impart excellent electrical insulation properties i.e. do not melt on heating or catches fire. Owing to this all electrical switches and sockets are capable of handling higher currents and operating temperatures. Front plates can be changed at any time with ease without disturbing the wiring to quickly and economically match changes in the surroundings.WORKTOP : Jet Black Granite: It should be 19mm (+/- 2mm) thick Jet Black Granite worktop. The exposed edges of the worktop should be chamfered and smoothened. The bottom of the worktop should be polished and there should be a V-groove throughout the length of the exposed edges to protect the cabinets from coming in contact with the spillages. The overhang on the storage cabinet is 25 mm at the front side and 30 mm at the sides. The backing material used is a neoprene mat of 6 mm thickness. as directed by Engineer In-charge(As per specified in Technical specification of furniture Page No.30 of NIT) |
| 51 | Providing supply installation of ISLAND TABLE - 14 3080mmL X 1540mmD X 900mmH WITH ELECTRICAL REGENT with 2 tier fixed type reagent rack having integrated electrical switch sockets Construction : Floor based Welded cabinet system having storage body should be flush face construction with intersection of vertical and horizontal members like LH and RH side panel along with front horizontal channel, back panel and bottom panel. It should be relocated anywhere easily as it is an independent unit. Cabinet should of square non-sharp edge construction. Doors should be assembled with SS-304 hinge assembly. Removable back panel should be provided to easily access the service lines running behind the cabinet benches. Intermediate horizontal channels should be provided between door and drawer. Toe-space of 90mm X 90mm is provided at front-bottom side of cabinet. Levelers are provided for easy leveling of welded cabinet. Shelf should be eight-bend panel with 20mm height. Drawer tray should be of single piece construction. Drawer should be well supported on LH and RH ball slide suspension system. Steel door and drawer front should be of double wall construction with sound dampening material filled inside. Doors should be easily removable and hinges should be easily replaceable. Knee space panel should be in 22 gauge construction. Cabinets are tested as per SEFA 8M standard from a SEFA approved Lab and also tested as per EN 14727 from a third party testing agencyDimensions: W=600 mm, D = 530mm, H = 875 mm Configurations: Continuous storageMOC: MSCRCA: IS – 513 (1994)Thickness: LH/RH side panels, shutter front, Bottom panel, Top front, Drawer separator, shelf, Alignment channel is of 1.2mm thk. Removable Back panel, Shutter cover, Fr. Rack strip, Top cover panel is of 0.8mmthk Finish: The complete M.S. material of cabinet should be pre-treated (degreased, Zinc phosphated) and epoxy powder coated for better corrosion resistance. The thickness of powder coat should be 45-50 microns, which passes the test of Salt Spray for 1000 hours. It should have a high temperature withstanding capacity with excellent electrical insulation properties.The rear portion of above accessories which is in contact with live metal should be made from thermo set material which will not melt on heating.Handle: Anodized Aluminum Recessed-Type, CTC: 160.0mm Lock: Units have a locking facility with 180° and 10 lever cam lock mechanism (except for sink and corner unit)Hinge: SS Hinge .Screw: SS 304.Shutter : should be of twin-type construction with sound dampening effect using profill. Shutter cover should be equipped with Bump on for sound dampening. Base Moulding should be made of PVC with corner clips. Ball Slide: 500mm Length Shutter should have provision of roller catch. COVER / FILLER PANELS All side cover panels and back panels, filler panels should be made from CRCA MS panels of 1.0mm thickness with pure epoxy powder coating . SERVICE FITTINGS AND ACCESSORIES Service fittings should be laboratory grade, and water faucets and valve bodies should be cast red brass alloy or bronze forgings, all fittings should be powder plated unless specified otherwise. Service Indexes: Fittings should be identified with service indexes in the color coding as per DIN 12920.Fixed-Type reagent shelves :It should be complete modular design consisting of 2 stage horizontal storage shelves made of CRCA MS with pure epoxy powder coating and having cutouts for electrical switches and sockets.ELECTRICAL ACCESSORIES (6/16 A SWITCHES & SOCKETS) : These are made of High gloss virgin grade engineering thermoplastics to impart a defect free surface. they impart excellent electrical insulation properties i.e. do not melt on heating or catches fire. Owing to this all electrical switches and sockets are capable of handling higher currents and operating temperatures. Front plates can be changed at any time with ease without disturbing the wiring to quickly and economically match changes in the surroundings.WORKTOP : Jet Black Granite: It should be 19mm (+/- 2mm) thick Jet Black Granite worktop. The exposed edges of the worktop should be chamfered and smoothened. The bottom of the worktop should be polished and there should be a V-groove throughout the length of the exposed edges to protect the cabinets from coming in contact with the spillages. The overhang on the storage cabinet is 25 mm at the front side and 30 mm at the sides. The backing material used is a neoprene mat of 6 mm thickness. as directed by Engineer In-charge(As per specified in Technical specification of furniture Page No.30 of NIT) |
| 52 | Providing supply installation of ISLAND TABLE - 8 3080mmL X 1540mmD X 900mmH WITH ELECTRICAL REGENT with 2 tier fixed type reagent rack having integrated electrical switch socketsConstruction : Floor based Welded cabinet system having storage body should be flush face construction with intersection of vertical and horizontal members like LH and RH side panel along with front horizontal channel, back panel and bottom panel. It should be relocated anywhere easily as it is an independent unit. Cabinet should of square non-sharp edge construction. Doors should be assembled with SS-304 hinge assembly. Removable back panel should be provided to easily access the service lines running behind the cabinet benches. Intermediate horizontal channels should be provided between door and drawer. Toe-space of 90mm X 90mm is provided at front-bottom side of cabinet. Levelers are provided for easy leveling of welded cabinet. Shelf should be eight-bend panel with 20mm height. Drawer tray should be of single piece construction. Drawer should be well supported on LH and RH ball slide suspension system. Steel door and drawer front should be of double wall construction with sound dampening material filled inside. Doors should be easily removable and hinges should be easily replaceable. Knee space panel should be in 22 gauge construction. Cabinets are tested as per SEFA 8M standard from a SEFA approved Lab and also tested as per EN 14727 from a third party testing agencyDimensions: W=600 mm, D = 530mm, H = 875 mm Configurations: Continuous storageMOC: MSCRCA: IS – 513 (1994)Thickness: LH/RH side panels, shutter front, Bottom panel, Top front, Drawer separator, shelf, Alignment channel is of 1.2mm thk. Removable Back panel, Shutter cover, Fr. Rack strip, Top cover panel is of 0.8mmthk Finish: The complete M.S. material of cabinet should be pre-treated (degreased, Zinc phosphated) and epoxy powder coated for better corrosion resistance. The thickness of powder coat should be 45-50 microns, which passes the test of Salt Spray for 1000 hours. It should have a high temperature withstanding capacity with excellent electrical insulation properties.The rear portion of above accessories which is in contact with live metal should be made from thermo set material which will not melt on heating.Handle: Anodized Aluminum Recessed-Type, CTC: 160.0mm Lock: Units have a locking facility with 180° and 10 lever cam lock mechanism (except for sink and corner unit)Hinge: SS Hinge .Screw: SS 304.Shutter : should be of twin-type construction with sound dampening effect using profill. Shutter cover should be equipped with Bump on for sound dampening. Base Moulding should be made of PVC with corner clips. Ball Slide: 500mm Length Shutter should have provision of roller catch. COVER / FILLER PANELS All side cover panels and back panels, filler panels should be made from CRCA MS panels of 1.0mm thickness with pure epoxy powder coating . SERVICE FITTINGS AND ACCESSORIES Service fittings should be laboratory grade, and water faucets and valve bodies should be cast red brass alloy or bronze forgings, all fittings should be powder plated unless specified otherwise. Service Indexes: Fittings should be identified with service indexes in the color coding as per DIN 12920.Fixed-Type reagent shelves :It should be complete modular design consisting of 2 stage horizontal storage shelves made of CRCA MS with pure epoxy powder coating and having cutouts for electrical switches and sockets.ELECTRICAL ACCESSORIES (6/16 A SWITCHES & SOCKETS) : These are made of High gloss virgin grade engineering thermoplastics to impart a defect free surface. they impart excellent electrical insulation properties i.e. do not melt on heating or catches fire. Owing to this all electrical switches and sockets are capable of handling higher currents and operating temperatures. Front plates can be changed at any time with ease without disturbing the wiring to quickly and economically match changes in the surroundings.WORKTOP : Jet Black Granite: It should be 19mm (+/- 2mm) thick Jet Black Granite worktop. The exposed edges of the worktop should be chamfered and smoothened. The bottom of the worktop should be polished and there should be a V-groove throughout the length of the exposed edges to protect the cabinets from coming in contact with the spillages. The overhang on the storage cabinet is 25 mm at the front side and 30 mm at the sides. The backing material used is a neoprene mat of 6 mm thickness. as directed by Engineer In-charge(As per specified in Technical specification of furniture Page No.30 of NIT) |
| 53 | Providing supply installation of ISLAND TABLE - 10 3660mmL X 1540mmD X 900mmH WITH ELECTRICALConstruction : Floor based Welded cabinet system having storage body should be flush face construction with intersection of vertical and horizontal members like LH and RH side panel along with front horizontal channel, back panel and bottom panel. It should be relocated anywhere easily as it is an independent unit. Cabinet should of square non-sharp edge construction. Doors should be assembled with SS-304 hinge assembly. Removable back panel should be provided to easily access the service lines running behind the cabinet benches. Intermediate horizontal channels should be provided between door and drawer. Toe-space of 90mm X 90mm is provided at front-bottom side of cabinet. Levelers are provided for easy leveling of welded cabinet. Shelf should be eight-bend panel with 20mm height. Drawer tray should be of single piece construction. Drawer should be well supported on LH and RH ball slide suspension system. Steel door and drawer front should be of double wall construction with sound dampening material filled inside. Doors should be easily removable and hinges should be easily replaceable. Knee space panel should be in 22 gauge construction. Cabinets are tested as per SEFA 8M standard from a SEFA approved Lab and also tested as per EN 14727 from a third party testing agencyDimensions: W=600 mm, 750 mm, 900mm , D = 530mm, H = 875 mm Configurations: continuous storages MOC: MSCRCA: IS – 513 (1994) Thickness: LH/RH side panels, shutter front, Bottom panel, Top front, Drawer separator, shelf, Alignment channel is of 1.2mm thk. Removable Back panel, Shutter cover, Fr. Rack strip, Top cover panel is of 0.8mmthk Finish: The complete M.S. material of cabinet should be pre-treated (degreased, Zinc phosphated) and epoxy powder coated for better corrosion resistance. The thickness of powder coat should be 45-50 microns, which passes the test of Salt Spray for 1000 hours. It should have a high temperature withstanding capacity with excellent electrical insulation properties.The rear portion of above accessories which is in contact with live metal should be made from thermo set material which will not melt on heating.Handle: Anodized Aluminum Recessed-Type, CTC: 160.0mm Lock: Units have a locking facility with 180° and 10 lever cam lock mechanism (except for sink and corner unit) Hinge: SS Hinge .Screw: SS 304.Shutter : should be of twin-type construction with sound dampening effect using profill. Shutter cover should be equipped with Bump on for sound dampening. Base Moulding should be made of PVC with corner clips. Ball Slide: 500mm Length Shutter should have provision of roller catch. COVER / FILLER PANELS All side cover panels and back panels, filler panels should be made from CRCA MS panels of 1.0mm thickness with pure epoxy powder coating . SERVICE FITTINGS AND ACCESSORIES Service fittings should be laboratory grade, and water faucets and valve bodies should be cast red brass alloy or bronze forgings, all fittings should be powder plated unless specified otherwise. Service Indexes: Fittings should be identified with service indexes in the color coding as per DIN 12920. ELECTRICAL ACCESSORIES (6/16 A SWITCHES & SOCKETS) : These are made of High gloss virgin grade engineering thermoplastics to impart a defect free surface. they impart excellent electrical insulation properties i.e. do not melt on heating or catches fire. Owing to this all electrical switches and sockets are capable of handling higher currents and operating temperatures. Front plates can be changed at any time with ease without disturbing the wiring to quickly and economically match changes in the surroundings.WORKTOP : Jet Black Granite: It should be 19mm (+/- 2mm) thick Jet Black Granite worktop. The exposed edges of the worktop should be chamfered and smoothened. The bottom of the worktop should be polished and there should be a V-groove throughout the length of the exposed edges to protect the cabinets from coming in contact with the spillages. The overhang on the storage cabinet is 25 mm at the front side and 30 mm at the sides. The backing material used is a neoprene mat of 6 mm thickness. as directed by Engineer In-charge(As per specified in Technical specification of furniture Page No.30 of NIT) |
| 54 | Providing supply installation of ISLAND TABLE - 13 3380mmL X 1540mmD X 900mmH WITH ELECTRICALConstruction : Floor based Welded cabinet system having storage body should be flush face construction with intersection of vertical and horizontal members like LH and RH side panel along with front horizontal channel, back panel and bottom panel. It should be relocated anywhere easily as it is an independent unit. Cabinet should of square non-sharp edge construction. Doors should be assembled with SS-304 hinge assembly. Removable back panel should be provided to easily access the service lines running behind the cabinet benches. Intermediate horizontal channels should be provided between door and drawer. Toe-space of 90mm X 90mm is provided at front-bottom side of cabinet. Levelers are provided for easy leveling of welded cabinet. Shelf should be eight-bend panel with 20mm height. Drawer tray should be of single piece construction. Drawer should be well supported on LH and RH ball slide suspension system. Steel door and drawer front should be of double wall construction with sound dampening material filled inside. Doors should be easily removable and hinges should be easily replaceable. Knee space panel should be in 22 gauge construction. Cabinets are tested as per SEFA 8M standard from a SEFA approved Lab and also tested as per EN 14727 from a third party testing agencyDimensions: W=600 mm, 750 mm, 900mm , D = 530mm, H = 875 mm Configurations: continuous storages MOC: MSCRCA: IS – 513 (1994) Thickness: LH/RH side panels, shutter front, Bottom panel, Top front, Drawer separator, shelf, Alignment channel is of 1.2mm thk. Removable Back panel, Shutter cover, Fr. Rack strip, Top cover panel is of 0.8mmthk Finish: The complete M.S. material of cabinet should be pre-treated (degreased, Zinc phosphated) and epoxy powder coated for better corrosion resistance. The thickness of powder coat should be 45-50 microns, which passes the test of Salt Spray for 1000 hours. It should have a high temperature withstanding capacity with excellent electrical insulation properties.The rear portion of above accessories which is in contact with live metal should be made from thermo set material which will not melt on heating.Handle: Anodized Aluminum Recessed-Type, CTC: 160.0mm Lock: Units have a locking facility with 180° and 10 lever cam lock mechanism (except for sink and corner unit) Hinge: SS Hinge .Screw: SS 304.Shutter : should be of twin-type construction with sound dampening effect using profill. Shutter cover should be equipped with Bump on for sound dampening. Base Moulding should be made of PVC with corner clips. Ball Slide: 500mm Length Shutter should have provision of roller catch. COVER / FILLER PANELS All side cover panels and back panels, filler panels should be made from CRCA MS panels of 1.0mm thickness with pure epoxy powder coating . SERVICE FITTINGS AND ACCESSORIES Service fittings should be laboratory grade, and water faucets and valve bodies should be cast red brass alloy or bronze forgings, all fittings should be powder plated unless specified otherwise. Service Indexes: Fittings should be identified with service indexes in the color coding as per DIN 12920. ELECTRICAL ACCESSORIES (6/16 A SWITCHES & SOCKETS) : These are made of High gloss virgin grade engineering thermoplastics to impart a defect free surface. they impart excellent electrical insulation properties i.e. do not melt on heating or catches fire. Owing to this all electrical switches and sockets are capable of handling higher currents and operating temperatures. Front plates can be changed at any time with ease without disturbing the wiring to quickly and economically match changes in the surroundings.WORKTOP : Jet Black Granite: It should be 19mm (+/- 2mm) thick Jet Black Granite worktop. The exposed edges of the worktop should be chamfered and smoothened. The bottom of the worktop should be polished and there should be a V-groove throughout the length of the exposed edges to protect the cabinets from coming in contact with the spillages. The overhang on the storage cabinet is 25 mm at the front side and 30 mm at the sides. The backing material used is a neoprene mat of 6 mm thickness. as directed by Engineer In-charge(As per specified in Technical specification of furniture Page No.30 of NIT) |
| 55 | Providing supply installation of ISLAND TABLE - 13 3380mmL X 1540mmD X 900mmH WITH ELECTRICAL TRUNKINGConstruction : Floor based Welded cabinet system having storage body should be flush face construction with intersection of vertical and horizontal members like LH and RH side panel along with front horizontal channel, back panel and bottom panel. It should be relocated anywhere easily as it is an independent unit. Cabinet should of square non-sharp edge construction. Doors should be assembled with SS-304 hinge assembly. Removable back panel should be provided to easily access the service lines running behind the cabinet benches. Intermediate horizontal channels should be provided between door and drawer. Toe-space of 90mm X 90mm is provided at front-bottom side of cabinet. Levelers are provided for easy leveling of welded cabinet. Shelf should be eight-bend panel with 20mm height. Drawer tray should be of single piece construction. Drawer should be well supported on LH and RH ball slide suspension system. Steel door and drawer front should be of double wall construction with sound dampening material filled inside. Doors should be easily removable and hinges should be easily replaceable. Knee space panel should be in 22 gauge construction. Cabinets are tested as per SEFA 8M standard from a SEFA approved Lab and also tested as per EN 14727 from a third party testing agencyDimensions: W=600 mm, 750 mm, 900mm , D = 530mm, H = 875 mm Configurations: continuous storages MOC: MSCRCA: IS – 513 (1994) Thickness: LH/RH side panels, shutter front, Bottom panel, Top front, Drawer separator, shelf, Alignment channel is of 1.2mm thk. Removable Back panel, Shutter cover, Fr. Rack strip, Top cover panel is of 0.8mmthk Finish: The complete M.S. material of cabinet should be pre-treated (degreased, Zinc phosphated) and epoxy powder coated for better corrosion resistance. The thickness of powder coat should be 45-50 microns, which passes the test of Salt Spray for 1000 hours. It should have a high temperature withstanding capacity with excellent electrical insulation properties.The rear portion of above accessories which is in contact with live metal should be made from thermo set material which will not melt on heating.Handle: Anodized Aluminum Recessed-Type, CTC: 160.0mm Lock: Units have a locking facility with 180° and 10 lever cam lock mechanism (except for sink and corner unit) Hinge: SS Hinge .Screw: SS 304.Shutter : should be of twin-type construction with sound dampening effect using profill. Shutter cover should be equipped with Bump on for sound dampening. Base Moulding should be made of PVC with corner clips. Ball Slide: 500mm Length Shutter should have provision of roller catch. COVER / FILLER PANELS All side cover panels and back panels, filler panels should be made from CRCA MS panels of 1.0mm thickness with pure epoxy powder coating . SERVICE FITTINGS AND ACCESSORIES Service fittings should be laboratory grade, and water faucets and valve bodies should be cast red brass alloy or bronze forgings, all fittings should be powder plated unless specified otherwise. Service Indexes: Fittings should be identified with service indexes in the color coding as per DIN 12920. ELECTRICAL ACCESSORIES (6/16 A SWITCHES & SOCKETS) : These are made of High gloss virgin grade engineering thermoplastics to impart a defect free surface. they impart excellent electrical insulation properties i.e. do not melt on heating or catches fire. Owing to this all electrical switches and sockets are capable of handling higher currents and operating temperatures. Front plates can be changed at any time with ease without disturbing the wiring to quickly and economically match changes in the surroundings.WORKTOP : Jet Black Granite: It should be 19mm (+/- 2mm) thick Jet Black Granite worktop. The exposed edges of the worktop should be chamfered and smoothened. The bottom of the worktop should be polished and there should be a V-groove throughout the length of the exposed edges to protect the cabinets from coming in contact with the spillages. The overhang on the storage cabinet is 25 mm at the front side and 30 mm at the sides. The backing material used is a neoprene mat of 6 mm thickness. as directed by Engineer In-charge(As per specified in Technical specification of furniture Page No.30 of NIT) |
| 56 | Providing supply installation of ISLAND TABLE - 4 3380mmL X 1540mmD X 900mmH WITH ELECTRICAL TRUNKINGConstruction : Floor based Welded cabinet system having storage body should be flush face construction with intersection of vertical and horizontal members like LH and RH side panel along with front horizontal channel, back panel and bottom panel. It should be relocated anywhere easily as it is an independent unit. Cabinet should of square non-sharp edge construction. Doors should be assembled with SS-304 hinge assembly. Removable back panel should be provided to easily access the service lines running behind the cabinet benches. Intermediate horizontal channels should be provided between door and drawer. Toe-space of 90mm X 90mm is provided at front-bottom side of cabinet. Levelers are provided for easy leveling of welded cabinet. Shelf should be eight-bend panel with 20mm height. Drawer tray should be of single piece construction. Drawer should be well supported on LH and RH ball slide suspension system. Steel door and drawer front should be of double wall construction with sound dampening material filled inside. Doors should be easily removable and hinges should be easily replaceable. Knee space panel should be in 22 gauge construction. Cabinets are tested as per SEFA 8M standard from a SEFA approved Lab and also tested as per EN 14727 from a third party testing agencyDimensions: W=600 mm, D = 530mm, H = 875 mm Configurations: Continuous storageMOC: MSCRCA: IS – 513 (1994)Thickness: LH/RH side panels, shutter front, Bottom panel, Top front, Drawer separator, shelf, Alignment channel is of 1.2mm thk. Removable Back panel, Shutter cover, Fr. Rack strip, Top cover panel is of 0.8mmthk Finish: The complete M.S. material of cabinet should be pre-treated (degreased, Zinc phosphated) and epoxy powder coated for better corrosion resistance. The thickness of powder coat should be 45-50 microns, which passes the test of Salt Spray for 1000 hours. It should have a high temperature withstanding capacity with excellent electrical insulation properties.The rear portion of above accessories which is in contact with live metal should be made from thermo set material which will not melt on heating.Handle: Anodized Aluminum Recessed-Type, CTC: 160.0mm Lock: Units have a locking facility with 180° and 10 lever cam lock mechanism (except for sink and corner unit)Hinge: SS Hinge .Screw: SS 304.Shutter : should be of twin-type construction with sound dampening effect using profill. Shutter cover should be equipped with Bump on for sound dampening. Base Moulding should be made of PVC with corner clips. Ball Slide: 500mm Length Shutter should have provision of roller catch. COVER / FILLER PANELS All side cover panels and back panels, filler panels should be made from CRCA MS panels of 1.0mm thickness with pure epoxy powder coating . SERVICE FITTINGS AND ACCESSORIES Service fittings should be laboratory grade, and water faucets and valve bodies should be cast red brass alloy or bronze forgings, all fittings should be powder plated unless specified otherwise. Service Indexes: Fittings should be identified with service indexes in the color coding as per DIN 12920.ELECTRICAL ACCESSORIES (6/16 A SWITCHES & SOCKETS) : These are made of High gloss virgin grade engineering thermoplastics to impart a defect free surface. they impart excellent electrical insulation properties i.e. do not melt on heating or catches fire. Owing to this all electrical switches and sockets are capable of handling higher currents and operating temperatures. Front plates can be changed at any time with ease without disturbing the wiring to quickly and economically match changes in the surroundings.WORKTOP : Jet Black Granite: It should be 19mm (+/- 2mm) thick Jet Black Granite worktop. The exposed edges of the worktop should be chamfered and smoothened. The bottom of the worktop should be polished and there should be a V-groove throughout the length of the exposed edges to protect the cabinets from coming in contact with the spillages. The overhang on the storage cabinet is 25 mm at the front side and 30 mm at the sides. The backing material used is a neoprene mat of 6 mm thickness. as directed by Engineer In-charge(As per specified in Technical specification of furniture Page No.30 of NIT) |
| 57 | Providing supply installation of ISLAND TABLE - 5 3060mmL X 1540mmD X 900mmH WITH SINK AND REAGENT RACK with 2 tier fixed type reagent rack having integrated electrical switch socketsConstruction : Floor based Welded cabinet system having storage body should be flush face construction with intersection of vertical and horizontal members like LH and RH side panel along with front horizontal channel, back panel and bottom panel. It should be relocated anywhere easily as it is an independent unit. Cabinet should of square non-sharp edge construction. Doors should be assembled with SS-304 hinge assembly. Removable back panel should be provided to easily access the service lines running behind the cabinet benches. Intermediate horizontal channels should be provided between door and drawer. Toe-space of 90mm X 90mm is provided at front-bottom side of cabinet. Levelers are provided for easy leveling of welded cabinet. Shelf should be eight-bend panel with 20mm height. Drawer tray should be of single piece construction. Drawer should be well supported on LH and RH ball slide suspension system. Steel door and drawer front should be of double wall construction with sound dampening material filled inside. Doors should be easily removable and hinges should be easily replaceable. Knee space panel should be in 22 gauge construction. Cabinets are tested as per SEFA 8M standard from a SEFA approved Lab and also tested as per EN 14727 from a third party testing agencyDimensions: W=600 mm, D = 530mm, H = 875 mm Configurations: Continuous storageMOC: MSCRCA: IS – 513 (1994)Thickness: LH/RH side panels, shutter front, Bottom panel, Top front, Drawer separator, shelf, Alignment channel is of 1.2mm thk. Removable Back panel, Shutter cover, Fr. Rack strip, Top cover panel is of 0.8mmthk Finish: The complete M.S. material of cabinet should be pre-treated (degreased, Zinc phosphated) and epoxy powder coated for better corrosion resistance. The thickness of powder coat should be 45-50 microns, which passes the test of Salt Spray for 1000 hours. It should have a high temperature withstanding capacity with excellent electrical insulation properties.The rear portion of above accessories which is in contact with live metal should be made from thermo set material which will not melt on heating.Handle: Anodized Aluminum Recessed-Type, CTC: 160.0mm Lock: Units have a locking facility with 180° and 10 lever cam lock mechanism (except for sink and corner unit)Hinge: SS Hinge .Screw: SS 304.Shutter : should be of twin-type construction with sound dampening effect using profill. Shutter cover should be equipped with Bump on for sound dampening. Base Moulding should be made of PVC with corner clips. Ball Slide: 500mm Length Shutter should have provision of roller catch. COVER / FILLER PANELS All side cover panels and back panels, filler panels should be made from CRCA MS panels of 1.0mm thickness with pure epoxy powder coating . SERVICE FITTINGS AND ACCESSORIES Service fittings should be laboratory grade, and water faucets and valve bodies should be cast red brass alloy or bronze forgings, all fittings should be powder plated unless specified otherwise. Service Indexes: Fittings should be identified with service indexes in the color coding as per DIN 12920.Fixed-Type reagent shelves :It should be complete modular design consisting of 2 stage horizontal storage shelves made of CRCA MS with pure epoxy powder coating and having cutouts for electrical switches and sockets.ELECTRICAL ACCESSORIES (6/16 A SWITCHES & SOCKETS) : These are made of High gloss virgin grade engineering thermoplastics to impart a defect free surface. they impart excellent electrical insulation properties i.e. do not melt on heating or catches fire. Owing to this all electrical switches and sockets are capable of handling higher currents and operating temperatures. Front plates can be changed at any time with ease without disturbing the wiring to quickly and economically match changes in the surroundings.WORKTOP : Jet Black Granite: It should be 19mm (+/- 2mm) thick Jet Black Granite worktop. The exposed edges of the worktop should be chamfered and smoothened. The bottom of the worktop should be polished and there should be a V-groove throughout the length of the exposed edges to protect the cabinets from coming in contact with the spillages. The overhang on the storage cabinet is 25 mm at the front side and 30 mm at the sides. The backing material used is a neoprene mat of 6 mm thickness. as directed by Engineer In-charge(As per specified in Technical specification of furniture Page No.30 of NIT) |
| 58 | Providing supply installation of ISLAND TABLE - 5 3080mmL X 1540mmD X 900mmH WITH ELECTRICAL TRUNKINGConstruction : Floor based Welded cabinet system having storage body should be flush face construction with intersection of vertical and horizontal members like LH and RH side panel along with front horizontal channel, back panel and bottom panel. It should be relocated anywhere easily as it is an independent unit. Cabinet should of square non-sharp edge construction. Doors should be assembled with SS-304 hinge assembly. Removable back panel should be provided to easily access the service lines running behind the cabinet benches. Intermediate horizontal channels should be provided between door and drawer. Toe-space of 90mm X 90mm is provided at front-bottom side of cabinet. Levelers are provided for easy leveling of welded cabinet. Shelf should be eight-bend panel with 20mm height. Drawer tray should be of single piece construction. Drawer should be well supported on LH and RH ball slide suspension system. Steel door and drawer front should be of double wall construction with sound dampening material filled inside. Doors should be easily removable and hinges should be easily replaceable. Knee space panel should be in 22 gauge construction. Cabinets are tested as per SEFA 8M standard from a SEFA approved Lab and also tested as per EN 14727 from a third party testing agencyDimensions: W=600 mm, 750 mm, 900mm , D = 530mm, H = 875 mm Configurations: continuous storages MOC: MSCRCA: IS – 513 (1994) Thickness: LH/RH side panels, shutter front, Bottom panel, Top front, Drawer separator, shelf, Alignment channel is of 1.2mm thk. Removable Back panel, Shutter cover, Fr. Rack strip, Top cover panel is of 0.8mmthk Finish: The complete M.S. material of cabinet should be pre-treated (degreased, Zinc phosphated) and epoxy powder coated for better corrosion resistance. The thickness of powder coat should be 45-50 microns, which passes the test of Salt Spray for 1000 hours. It should have a high temperature withstanding capacity with excellent electrical insulation properties.The rear portion of above accessories which is in contact with live metal should be made from thermo set material which will not melt on heating.Handle: Anodized Aluminum Recessed-Type, CTC: 160.0mm Lock: Units have a locking facility with 180° and 10 lever cam lock mechanism (except for sink and corner unit) Hinge: SS Hinge .Screw: SS 304.Shutter : should be of twin-type construction with sound dampening effect using profill. Shutter cover should be equipped with Bump on for sound dampening. Base Moulding should be made of PVC with corner clips. Ball Slide: 500mm Length Shutter should have provision of roller catch. COVER / FILLER PANELS All side cover panels and back panels, filler panels should be made from CRCA MS panels of 1.0mm thickness with pure epoxy powder coating . SERVICE FITTINGS AND ACCESSORIES Service fittings should be laboratory grade, and water faucets and valve bodies should be cast red brass alloy or bronze forgings, all fittings should be powder plated unless specified otherwise. Service Indexes: Fittings should be identified with service indexes in the color coding as per DIN 12920. ELECTRICAL ACCESSORIES (6/16 A SWITCHES & SOCKETS) : These are made of High gloss virgin grade engineering thermoplastics to impart a defect free surface. they impart excellent electrical insulation properties i.e. do not melt on heating or catches fire. Owing to this all electrical switches and sockets are capable of handling higher currents and operating temperatures. Front plates can be changed at any time with ease without disturbing the wiring to quickly and economically match changes in the surroundings.WORKTOP : Jet Black Granite: It should be 19mm (+/- 2mm) thick Jet Black Granite worktop. The exposed edges of the worktop should be chamfered and smoothened. The bottom of the worktop should be polished and there should be a V-groove throughout the length of the exposed edges to protect the cabinets from coming in contact with the spillages. The overhang on the storage cabinet is 25 mm at the front side and 30 mm at the sides. The backing material used is a neoprene mat of 6 mm thickness. as directed by Engineer In-charge(As per specified in Technical specification of furniture Page No.30 of NIT) |
| 59 | Providing supply installation of ISLAND TABLE - 9 3060mmL X 1540mmD X 900mmH WITH SINK AND REAGENT RACK with 2 tier fixed type reagent rack having integrated electrical switch socketsConstruction : Floor based Welded cabinet system having storage body should be flush face construction with intersection of vertical and horizontal members like LH and RH side panel along with front horizontal channel, back panel and bottom panel. It should be relocated anywhere easily as it is an independent unit. Cabinet should of square non-sharp edge construction. Doors should be assembled with SS-304 hinge assembly. Removable back panel should be provided to easily access the service lines running behind the cabinet benches. Intermediate horizontal channels should be provided between door and drawer. Toe-space of 90mm X 90mm is provided at front-bottom side of cabinet. Levelers are provided for easy leveling of welded cabinet. Shelf should be eight-bend panel with 20mm height. Drawer tray should be of single piece construction. Drawer should be well supported on LH and RH ball slide suspension system. Steel door and drawer front should be of double wall construction with sound dampening material filled inside. Doors should be easily removable and hinges should be easily replaceable. Knee space panel should be in 22 gauge construction. Cabinets are tested as per SEFA 8M standard from a SEFA approved Lab and also tested as per EN 14727 from a third party testing agencyDimensions: W=600 mm, D = 530mm, H = 875 mm Configurations: Continuous storageMOC: MSCRCA: IS – 513 (1994)Thickness: LH/RH side panels, shutter front, Bottom panel, Top front, Drawer separator, shelf, Alignment channel is of 1.2mm thk. Removable Back panel, Shutter cover, Fr. Rack strip, Top cover panel is of 0.8mmthk Finish: The complete M.S. material of cabinet should be pre-treated (degreased, Zinc phosphated) and epoxy powder coated for better corrosion resistance. The thickness of powder coat should be 45-50 microns, which passes the test of Salt Spray for 1000 hours. It should have a high temperature withstanding capacity with excellent electrical insulation properties.The rear portion of above accessories which is in contact with live metal should be made from thermo set material which will not melt on heating.Handle: Anodized Aluminum Recessed-Type, CTC: 160.0mm Lock: Units have a locking facility with 180° and 10 lever cam lock mechanism (except for sink and corner unit)Hinge: SS Hinge .Screw: SS 304.Shutter : should be of twin-type construction with sound dampening effect using profill. Shutter cover should be equipped with Bump on for sound dampening. Base Moulding should be made of PVC with corner clips. Ball Slide: 500mm Length Shutter should have provision of roller catch. COVER / FILLER PANELS All side cover panels and back panels, filler panels should be made from CRCA MS panels of 1.0mm thickness with pure epoxy powder coating . SERVICE FITTINGS AND ACCESSORIES Service fittings should be laboratory grade, and water faucets and valve bodies should be cast red brass alloy or bronze forgings, all fittings should be powder plated unless specified otherwise. Service Indexes: Fittings should be identified with service indexes in the color coding as per DIN 12920.Fixed-Type reagent shelves :It should be complete modular design consisting of 2 stage horizontal storage shelves made of CRCA MS with pure epoxy powder coating and having cutouts for electrical switches and sockets.ELECTRICAL ACCESSORIES (6/16 A SWITCHES & SOCKETS) : These are made of High gloss virgin grade engineering thermoplastics to impart a defect free surface. they impart excellent electrical insulation properties i.e. do not melt on heating or catches fire. Owing to this all electrical switches and sockets are capable of handling higher currents and operating temperatures. Front plates can be changed at any time with ease without disturbing the wiring to quickly and economically match changes in the surroundings.PP Sink: ,Polypropylene Molded Sinks: Made up of 5 mm thick high density and elastic poly propylene with good resistance to organic solvents. Sink - Bowl size to be a minimum of (L x W x D) 560 x 355 x 300 mm. Faucet - 3-way type faucet as per approved makeWORKTOP : Jet Black Granite: It should be 19mm (+/- 2mm) thick Jet Black Granite worktop. The exposed edges of the worktop should be chamfered and smoothened. The bottom of the worktop should be polished and there should be a V-groove throughout the length of the exposed edges to protect the cabinets from coming in contact with the spillages. The overhang on the storage cabinet is 25 mm at the front side and 30 mm at the sides. The backing material used is a neoprene mat of 6 mm thickness. as directed by Engineer In-charge(As per specified in Technical specification of furniture Page No.30 of NIT) |
| 60 | Providing supply installation of ISLAND TABLE WITH ELECTRICAL TRUNKING - 4 3080mmL X 1540mmD X 900mmHConstruction : Floor based Welded cabinet system having storage body should be flush face construction with intersection of vertical and horizontal members like LH and RH side panel along with front horizontal channel, back panel and bottom panel. It should be relocated anywhere easily as it is an independent unit. Cabinet should of square non-sharp edge construction. Doors should be assembled with SS-304 hinge assembly. Removable back panel should be provided to easily access the service lines running behind the cabinet benches. Intermediate horizontal channels should be provided between door and drawer. Toe-space of 90mm X 90mm is provided at front-bottom side of cabinet. Levelers are provided for easy leveling of welded cabinet. Shelf should be eight-bend panel with 20mm height. Drawer tray should be of single piece construction. Drawer should be well supported on LH and RH ball slide suspension system. Steel door and drawer front should be of double wall construction with sound dampening material filled inside. Doors should be easily removable and hinges should be easily replaceable. Knee space panel should be in 22 gauge construction. Cabinets are tested as per SEFA 8M standard from a SEFA approved Lab and also tested as per EN 14727 from a third party testing agencyDimensions: W=600 mm, D = 530mm, H = 875 mm Configurations: Continuous storage MOC: MSCRCA: IS – 513 (1994)Thickness: LH/RH side panels, shutter front, Bottom panel, Top front, Drawer separator, shelf, Alignment channel is of 1.2mm thk. Removable Back panel, Shutter cover, Fr. Rack strip, Top cover panel is of 0.8mmthk Finish: The complete M.S. material of cabinet should be pre-treated (degreased, Zinc phosphated) and epoxy powder coated for better corrosion resistance. The thickness of powder coat should be 45-50 microns, which passes the test of Salt Spray for 1000 hours. It should have a high temperature withstanding capacity with excellent electrical insulation properties.The rear portion of above accessories which is in contact with live metal should be made from thermo set material which will not melt on heating.Handle: Anodized Aluminum Recessed-Type, CTC: 160.0mm Lock: Units have a locking facility with 180° and 10 lever cam lock mechanism (except for sink and corner unit)Hinge: SS Hinge .Screw: SS 304.Shutter : should be of twin-type construction with sound dampening effect using profill. Shutter cover should be equipped with Bump on for sound dampening. Base Moulding should be made of PVC with corner clips. Ball Slide: 500mm Length Shutter should have provision of roller catch. COVER / FILLER PANELS All side cover panels and back panels, filler panels should be made from CRCA MS panels of 1.0mm thickness with pure epoxy powder coating . SERVICE FITTINGS AND ACCESSORIES Service fittings should be laboratory grade, and water faucets and valve bodies should be cast red brass alloy or bronze forgings, all fittings should be powder plated unless specified otherwise. Service Indexes: Fittings should be identified with service indexes in the color coding as per DIN 12920.ELECTRICAL ACCESSORIES (6/16 A SWITCHES & SOCKETS) : These are made of High gloss virgin grade engineering thermoplastics to impart a defect free surface. they impart excellent electrical insulation properties i.e. do not melt on heating or catches fire. Owing to this all electrical switches and sockets are capable of handling higher currents and operating temperatures. Front plates can be changed at any time with ease without disturbing the wiring to quickly and economically match changes in the surroundings.WORKTOP : Jet Black Granite: It should be 19mm (+/- 2mm) thick Jet Black Granite worktop. The exposed edges of the worktop should be chamfered and smoothened. The bottom of the worktop should be polished and there should be a V-groove throughout the length of the exposed edges to protect the cabinets from coming in contact with the spillages. The overhang on the storage cabinet is 25 mm at the front side and 30 mm at the sides. The backing material used is a neoprene mat of 6 mm thickness. as directed by Engineer In-charge (As per specified in Technical specification of furniture Page No.30 of NIT) |
| 61 | Providing supply installation of ISLAND TABLE WITH SINK - 5 3060mmL X 1540mmD X 900mmH WITH ELECTRICAL REGENT with 2 tier fixed type reagent rack having integrated electrical switch socketsConstruction : Floor based Welded cabinet system having storage body should be flush face construction with intersection of vertical and horizontal members like LH and RH side panel along with front horizontal channel, back panel and bottom panel. It should be relocated anywhere easily as it is an independent unit. Cabinet should of square non-sharp edge construction. Doors should be assembled with SS-304 hinge assembly. Removable back panel should be provided to easily access the service lines running behind the cabinet benches. Intermediate horizontal channels should be provided between door and drawer. Toe-space of 90mm X 90mm is provided at front-bottom side of cabinet. Levelers are provided for easy leveling of welded cabinet. Shelf should be eight-bend panel with 20mm height. Drawer tray should be of single piece construction. Drawer should be well supported on LH and RH ball slide suspension system. Steel door and drawer front should be of double wall construction with sound dampening material filled inside. Doors should be easily removable and hinges should be easily replaceable. Knee space panel should be in 22 gauge construction. Cabinets are tested as per SEFA 8M standard from a SEFA approved Lab and also tested as per EN 14727 from a third party testing agencyDimensions: W=600 mm, D = 530mm, H = 875 mm Configurations: Continuous storageMOC: MSCRCA: IS – 513 (1994)Thickness: LH/RH side panels, shutter front, Bottom panel, Top front, Drawer separator, shelf, Alignment channel is of 1.2mm thk. Removable Back panel, Shutter cover, Fr. Rack strip, Top cover panel is of 0.8mmthk Finish: The complete M.S. material of cabinet should be pre-treated (degreased, Zinc phosphated) and epoxy powder coated for better corrosion resistance. The thickness of powder coat should be 45-50 microns, which passes the test of Salt Spray for 1000 hours. It should have a high temperature withstanding capacity with excellent electrical insulation properties.The rear portion of above accessories which is in contact with live metal should be made from thermo set material which will not melt on heating.Handle: Anodized Aluminum Recessed-Type, CTC: 160.0mm Lock: Units have a locking facility with 180° and 10 lever cam lock mechanism (except for sink and corner unit)Hinge: SS Hinge .Screw: SS 304.Shutter : should be of twin-type construction with sound dampening effect using profill. Shutter cover should be equipped with Bump on for sound dampening. Base Moulding should be made of PVC with corner clips. Ball Slide: 500mm Length Shutter should have provision of roller catch. COVER / FILLER PANELS All side cover panels and back panels, filler panels should be made from CRCA MS panels of 1.0mm thickness with pure epoxy powder coating . SERVICE FITTINGS AND ACCESSORIES Service fittings should be laboratory grade, and water faucets and valve bodies should be cast red brass alloy or bronze forgings, all fittings should be powder plated unless specified otherwise. Service Indexes: Fittings should be identified with service indexes in the color coding as per DIN 12920.Fixed-Type reagent shelves :It should be complete modular design consisting of 2 stage horizontal storage shelves made of CRCA MS with pure epoxy powder coating and having cutouts for electrical switches and sockets.ELECTRICAL ACCESSORIES (6/16 A SWITCHES & SOCKETS) : These are made of High gloss virgin grade engineering thermoplastics to impart a defect free surface. they impart excellent electrical insulation properties i.e. do not melt on heating or catches fire. Owing to this all electrical switches and sockets are capable of handling higher currents and operating temperatures. Front plates can be changed at any time with ease without disturbing the wiring to quickly and economically match changes in the surroundings.PP Sink: ,Polypropylene Molded Sinks: Made up of 5 mm thick high density and elastic poly propylene with good resistance to organic solvents. Sink - Bowl size to be a minimum of (L x W x D) 560 x 355 x 300 mm. Faucet - 3-way type faucet as per approved makeWORKTOP : Jet Black Granite: It should be 19mm (+/- 2mm) thick Jet Black Granite worktop. The exposed edges of the worktop should be chamfered and smoothened. The bottom of the worktop should be polished and there should be a V-groove throughout the length of the exposed edges to protect the cabinets from coming in contact with the spillages. The overhang on the storage cabinet is 25 mm at the front side and 30 mm at the sides. The backing material used is a neoprene mat of 6 mm thickness. as directed by Engineer In-charge(As per specified in Technical specification of furniture Page No.30 of NIT) |
| 62 | Providing supply installation of ISLAND TABLE - 9 3060mmL X 1540mmD X 900mmH WITH SINK AND REAGENT RACK with 2 tier fixed type reagent rack having integrated electrical switch socketsConstruction : Floor based Welded cabinet system having storage body should be flush face construction with intersection of vertical and horizontal members like LH and RH side panel along with front horizontal channel, back panel and bottom panel. It should be relocated anywhere easily as it is an independent unit. Cabinet should of square non-sharp edge construction. Doors should be assembled with SS-304 hinge assembly. Removable back panel should be provided to easily access the service lines running behind the cabinet benches. Intermediate horizontal channels should be provided between door and drawer. Toe-space of 90mm X 90mm is provided at front-bottom side of cabinet. Levelers are provided for easy leveling of welded cabinet. Shelf should be eight-bend panel with 20mm height. Drawer tray should be of single piece construction. Drawer should be well supported on LH and RH ball slide suspension system. Steel door and drawer front should be of double wall construction with sound dampening material filled inside. Doors should be easily removable and hinges should be easily replaceable. Knee space panel should be in 22 gauge construction. Cabinets are tested as per SEFA 8M standard from a SEFA approved Lab and also tested as per EN 14727 from a third party testing agencyDimensions: W=600 mm, D = 530mm, H = 875 mm Configurations: Continuous storageMOC: MSCRCA: IS – 513 (1994)Thickness: LH/RH side panels, shutter front, Bottom panel, Top front, Drawer separator, shelf, Alignment channel is of 1.2mm thk. Removable Back panel, Shutter cover, Fr. Rack strip, Top cover panel is of 0.8mmthk Finish: The complete M.S. material of cabinet should be pre-treated (degreased, Zinc phosphated) and epoxy powder coated for better corrosion resistance. The thickness of powder coat should be 45-50 microns, which passes the test of Salt Spray for 1000 hours. It should have a high temperature withstanding capacity with excellent electrical insulation properties.The rear portion of above accessories which is in contact with live metal should be made from thermo set material which will not melt on heating.Handle: Anodized Aluminum Recessed-Type, CTC: 160.0mm Lock: Units have a locking facility with 180° and 10 lever cam lock mechanism (except for sink and corner unit)Hinge: SS Hinge .Screw: SS 304.Shutter : should be of twin-type construction with sound dampening effect using profill. Shutter cover should be equipped with Bump on for sound dampening. Base Moulding should be made of PVC with corner clips. Ball Slide: 500mm Length Shutter should have provision of roller catch. COVER / FILLER PANELS All side cover panels and back panels, filler panels should be made from CRCA MS panels of 1.0mm thickness with pure epoxy powder coating . SERVICE FITTINGS AND ACCESSORIES Service fittings should be laboratory grade, and water faucets and valve bodies should be cast red brass alloy or bronze forgings, all fittings should be powder plated unless specified otherwise. Service Indexes: Fittings should be identified with service indexes in the color coding as per DIN 12920.Fixed-Type reagent shelves :It should be complete modular design consisting of 2 stage horizontal storage shelves made of CRCA MS with pure epoxy powder coating and having cutouts for electrical switches and sockets.ELECTRICAL ACCESSORIES (6/16 A SWITCHES & SOCKETS) : These are made of High gloss virgin grade engineering thermoplastics to impart a defect free surface. they impart excellent electrical insulation properties i.e. do not melt on heating or catches fire. Owing to this all electrical switches and sockets are capable of handling higher currents and operating temperatures. Front plates can be changed at any time with ease without disturbing the wiring to quickly and economically match changes in the surroundings.PP Sink: ,Polypropylene Molded Sinks: Made up of 5 mm thick high density and elastic poly propylene with good resistance to organic solvents. Sink - Bowl size to be a minimum of (L x W x D) 560 x 355 x 300 mm. Faucet - 3-way type faucet as per approved makeWORKTOP : Jet Black Granite: It should be 19mm (+/- 2mm) thick Jet Black Granite worktop. The exposed edges of the worktop should be chamfered and smoothened. The bottom of the worktop should be polished and there should be a V-groove throughout the length of the exposed edges to protect the cabinets from coming in contact with the spillages. The overhang on the storage cabinet is 25 mm at the front side and 30 mm at the sides. The backing material used is a neoprene mat of 6 mm thickness. as directed by Engineer In-charge(As per specified in Technical specification of furniture Page No.30 of NIT) |
| 63 | Providing supply installation of ISLAND TABLE - 9 3060mmL X 1540mmD X 900mmH WITH SINK AND REAGENT RACK with 2 tier fixed type reagent rack having integrated electrical switch socketsConstruction : Floor based Welded cabinet system having storage body should be flush face construction with intersection of vertical and horizontal members like LH and RH side panel along with front horizontal channel, back panel and bottom panel. It should be relocated anywhere easily as it is an independent unit. Cabinet should of square non-sharp edge construction. Doors should be assembled with SS-304 hinge assembly. Removable back panel should be provided to easily access the service lines running behind the cabinet benches. Intermediate horizontal channels should be provided between door and drawer. Toe-space of 90mm X 90mm is provided at front-bottom side of cabinet. Levelers are provided for easy leveling of welded cabinet. Shelf should be eight-bend panel with 20mm height. Drawer tray should be of single piece construction. Drawer should be well supported on LH and RH ball slide suspension system. Steel door and drawer front should be of double wall construction with sound dampening material filled inside. Doors should be easily removable and hinges should be easily replaceable. Knee space panel should be in 22 gauge construction. Cabinets are tested as per SEFA 8M standard from a SEFA approved Lab and also tested as per EN 14727 from a third party testing agencyDimensions: W=600 mm, D = 530mm, H = 875 mm Configurations: Continuous storageMOC: MSCRCA: IS – 513 (1994)Thickness: LH/RH side panels, shutter front, Bottom panel, Top front, Drawer separator, shelf, Alignment channel is of 1.2mm thk. Removable Back panel, Shutter cover, Fr. Rack strip, Top cover panel is of 0.8mmthk Finish: The complete M.S. material of cabinet should be pre-treated (degreased, Zinc phosphated) and epoxy powder coated for better corrosion resistance. The thickness of powder coat should be 45-50 microns, which passes the test of Salt Spray for 1000 hours. It should have a high temperature withstanding capacity with excellent electrical insulation properties.The rear portion of above accessories which is in contact with live metal should be made from thermo set material which will not melt on heating.Handle: Anodized Aluminum Recessed-Type, CTC: 160.0mm Lock: Units have a locking facility with 180° and 10 lever cam lock mechanism (except for sink and corner unit)Hinge: SS Hinge .Screw: SS 304.Shutter : should be of twin-type construction with sound dampening effect using profill. Shutter cover should be equipped with Bump on for sound dampening. Base Moulding should be made of PVC with corner clips. Ball Slide: 500mm Length Shutter should have provision of roller catch. COVER / FILLER PANELS All side cover panels and back panels, filler panels should be made from CRCA MS panels of 1.0mm thickness with pure epoxy powder coating . SERVICE FITTINGS AND ACCESSORIES Service fittings should be laboratory grade, and water faucets and valve bodies should be cast red brass alloy or bronze forgings, all fittings should be powder plated unless specified otherwise. Service Indexes: Fittings should be identified with service indexes in the color coding as per DIN 12920.Fixed-Type reagent shelves :It should be complete modular design consisting of 2 stage horizontal storage shelves made of CRCA MS with pure epoxy powder coating and having cutouts for electrical switches and sockets.ELECTRICAL ACCESSORIES (6/16 A SWITCHES & SOCKETS) : These are made of High gloss virgin grade engineering thermoplastics to impart a defect free surface. they impart excellent electrical insulation properties i.e. do not melt on heating or catches fire. Owing to this all electrical switches and sockets are capable of handling higher currents and operating temperatures. Front plates can be changed at any time with ease without disturbing the wiring to quickly and economically match changes in the surroundings.PP Sink: ,Polypropylene Molded Sinks: Made up of 5 mm thick high density and elastic poly propylene with good resistance to organic solvents. Sink - Bowl size to be a minimum of (L x W x D) 560 x 355 x 300 mm. Faucet - 3-way type faucet as per approved makeWORKTOP : Jet Black Granite: It should be 19mm (+/- 2mm) thick Jet Black Granite worktop. The exposed edges of the worktop should be chamfered and smoothened. The bottom of the worktop should be polished and there should be a V-groove throughout the length of the exposed edges to protect the cabinets from coming in contact with the spillages. The overhang on the storage cabinet is 25 mm at the front side and 30 mm at the sides. The backing material used is a neoprene mat of 6 mm thickness. as directed by Engineer In-charge(As per specified in Technical specification of furniture Page No.30 of NIT) |
| 64 | Providing supply installation of ISLAND TABLE WITH SINK - 9 3060mmL X 1540mmD X 900mmH WITH ELECTRICAL REGENT SHELF with 2 tier fixed type reagent rack having integrated electrical switch socketsConstruction : Floor based Welded cabinet system having storage body should be flush face construction with intersection of vertical and horizontal members like LH and RH side panel along with front horizontal channel, back panel and bottom panel. It should be relocated anywhere easily as it is an independent unit. Cabinet should of square non-sharp edge construction. Doors should be assembled with SS-304 hinge assembly. Removable back panel should be provided to easily access the service lines running behind the cabinet benches. Intermediate horizontal channels should be provided between door and drawer. Toe-space of 90mm X 90mm is provided at front-bottom side of cabinet. Levelers are provided for easy leveling of welded cabinet. Shelf should be eight-bend panel with 20mm height. Drawer tray should be of single piece construction. Drawer should be well supported on LH and RH ball slide suspension system. Steel door and drawer front should be of double wall construction with sound dampening material filled inside. Doors should be easily removable and hinges should be easily replaceable. Knee space panel should be in 22 gauge construction. Cabinets are tested as per SEFA 8M standard from a SEFA approved Lab and also tested as per EN 14727 from a third party testing agencyDimensions: W=600 mm, D = 530mm, H = 875 mm Configurations: Continuous storageMOC: MSCRCA: IS – 513 (1994)Thickness: LH/RH side panels, shutter front, Bottom panel, Top front, Drawer separator, shelf, Alignment channel is of 1.2mm thk. Removable Back panel, Shutter cover, Fr. Rack strip, Top cover panel is of 0.8mmthk Finish: The complete M.S. material of cabinet should be pre-treated (degreased, Zinc phosphated) and epoxy powder coated for better corrosion resistance. The thickness of powder coat should be 45-50 microns, which passes the test of Salt Spray for 1000 hours. It should have a high temperature withstanding capacity with excellent electrical insulation properties.The rear portion of above accessories which is in contact with live metal should be made from thermo set material which will not melt on heating.Handle: Anodized Aluminum Recessed-Type, CTC: 160.0mm Lock: Units have a locking facility with 180° and 10 lever cam lock mechanism (except for sink and corner unit)Hinge: SS Hinge .Screw: SS 304.Shutter : should be of twin-type construction with sound dampening effect using profill. Shutter cover should be equipped with Bump on for sound dampening. Base Moulding should be made of PVC with corner clips. Ball Slide: 500mm Length Shutter should have provision of roller catch. COVER / FILLER PANELS All side cover panels and back panels, filler panels should be made from CRCA MS panels of 1.0mm thickness with pure epoxy powder coating . SERVICE FITTINGS AND ACCESSORIES Service fittings should be laboratory grade, and water faucets and valve bodies should be cast red brass alloy or bronze forgings, all fittings should be powder plated unless specified otherwise. Service Indexes: Fittings should be identified with service indexes in the color coding as per DIN 12920.Fixed-Type reagent shelves :It should be complete modular design consisting of 2 stage horizontal storage shelves made of CRCA MS with pure epoxy powder coating and having cutouts for electrical switches and sockets.ELECTRICAL ACCESSORIES (6/16 A SWITCHES & SOCKETS) : These are made of High gloss virgin grade engineering thermoplastics to impart a defect free surface. they impart excellent electrical insulation properties i.e. do not melt on heating or catches fire. Owing to this all electrical switches and sockets are capable of handling higher currents and operating temperatures. Front plates can be changed at any time with ease without disturbing the wiring to quickly and economically match changes in the surroundings.PP Sink,Polypropylene Molded Sinks: Made up of 5 mm thick high density and elastic poly propylene with good resistance to organic solvents. Sink - Bowl size to be a minimum of (L x W x D) 560 x 355 x 300 mm. Faucet - 3-way type faucet as per approved make WORKTOP : Jet Black Granite: It should be 19mm (+/- 2mm) thick Jet Black Granite worktop. The exposed edges of the worktop should be chamfered and smoothened. The bottom of the worktop should be polished and there should be a V-groove throughout the length of the exposed edges to protect the cabinets from coming in contact with the spillages. The overhang on the storage cabinet is 25 mm at the front side and 30 mm at the sides. The backing material used is a neoprene mat of 6 mm thickness. as directed by Engineer In-charge(As per specified in Technical specification of furniture Page No.30 of NIT) |
| 65 | Providing supply installation of MS APPRATUS STORAGE -4 900mmL X 560mmD X 1800mmH having The material of construction is 1.2 mm CRCA MS with pure epoxy powder coating (dry film thickness 40 to 60 microns) fitted with float glass to enable clear visibility inside the cabinet. It has louvers/perforations for air supply. Cabinet should come with 3 Adj plus 1 fixed type in 1800 heigh with maximum load carrying capacity of 75 Kg UDL. Shutter LH and RH panel is hinge type and have sandwich door construction made up of 1.2 mm thick shutter front panel and 0.8 mm shutter real panel.Cabinet come with SS 304 hinges: 3 nos. of hinge per shutter and screw fitted to each shutter and unit.It should come with cam lock and nylon-based M-10 levelers which are mounted on triangular plate.Handle should be aluminum recess type flush handle. Glass should be 4mm thick toughened type fixed in between shutter front and cover using metal strip and rubber beading.It is used for storages of equipment, consumables, files and any non-chemical (powder based) components. as directed by Engineer In-charge(As per specified in Technical specification of furniture Page No.30 of NIT) |
| 66 | Providing supply installation of MS APPRATUS STORAGE -4 900mmL X 560mmD X 1800mmH having The material of construction is 1.2 mm CRCA MS with pure epoxy powder coating (dry film thickness 40 to 60 microns) fitted with float glass to enable clear visibility inside the cabinet. It has louvers/perforations for air supply. Cabinet should come with 3 Adj plus 1 fixed type in 1800 heigh with maximum load carrying capacity of 75 Kg UDL. Shutter LH and RH panel is hinge type and have sandwich door construction made up of 1.2 mm thick shutter front panel and 0.8 mm shutter real panel.Cabinet come with SS 304 hinges: 3 nos. of hinge per shutter and screw fitted to each shutter and unit.It should come with cam lock and nylon-based M-10 levelers which are mounted on triangular plate.Handle should be aluminum recess type flush handle. Glass should be 4mm thick toughened type fixed in between shutter front and cover using metal strip and rubber beading.It is used for storages of equipment, consumables, files and any non-chemical (powder based) components. as directed by Engineer In-charge(As per specified in Technical specification of furniture Page No.30 of NIT) |
| 67 | Providing supply installation of MS APPRATUS STORAGE -4 900mmL X 560mmD X 1800mmH having The material of construction is 1.2 mm CRCA MS with pure epoxy powder coating (dry film thickness 40 to 60 microns) fitted with float glass to enable clear visibility inside the cabinet. It has louvers/perforations for air supply. Cabinet should come with 3 Adj plus 1 fixed type in 1800 heigh with maximum load carrying capacity of 75 Kg UDL. Shutter LH and RH panel is hinge type and have sandwich door construction made up of 1.2 mm thick shutter front panel and 0.8 mm shutter real panel.Cabinet come with SS 304 hinges: 3 nos. of hinge per shutter and screw fitted to each shutter and unit.It should come with cam lock and nylon-based M-10 levelers which are mounted on triangular plate.Handle should be aluminum recess type flush handle. Glass should be 4mm thick toughened type fixed in between shutter front and cover using metal strip and rubber beading.It is used for storages of equipment, consumables, files and any non-chemical (powder based) components. as directed by Engineer In-charge(As per specified in Technical specification of furniture Page No.30 of NIT) |
| 68 | Providing supply installation of MS APPRATUS STORAGE -4 900mmL X 560mmD X 1800mmH having The material of construction is 1.2 mm CRCA MS with pure epoxy powder coating (dry film thickness 40 to 60 microns) fitted with float glass to enable clear visibility inside the cabinet. It has louvers/perforations for air supply. Cabinet should come with 3 Adj plus 1 fixed type in 1800 heigh with maximum load carrying capacity of 75 Kg UDL. Shutter LH and RH panel is hinge type and have sandwich door construction made up of 1.2 mm thick shutter front panel and 0.8 mm shutter real panel.Cabinet come with SS 304 hinges: 3 nos. of hinge per shutter and screw fitted to each shutter and unit.It should come with cam lock and nylon-based M-10 levelers which are mounted on triangular plate.Handle should be aluminum recess type flush handle. Glass should be 4mm thick toughened type fixed in between shutter front and cover using metal strip and rubber beading.It is used for storages of equipment, consumables, files and any non-chemical (powder based) components. as directed by Engineer In-charge(As per specified in Technical specification of furniture Page No.30 of NIT) |
| 69 | Providing supply installation of Chemical Storage Base Cabinet (1000mm Wide x 1500 mm H ) with Ventilation , Storage cabinets are designed to safely store highly corrosive acids. With a full PP construction, the cabinets are completely protected from corrosion, making them the preferred choice in labs and workspaces dealing with aggressive chemicals. cabinet provides you with a storage solution that easily outperforms the metal and wooden storages. All safety claims of this product are backed by third party certification for Chemical Spot Test for 49 chemicals listed in SEFA standards, the product must be 3rd party tested as per SEFA 8P and used across various industries. The cabinet has been designed to be fully ventilated ensuring air circulation and preventing a build-up of dangerous fumes within the cabinet. The shelves comprise of removable height adjustable collection trays that are leak-proof, enhancing the safety factor of the storage units.Exhaust Provision: There is an air-duct at the back, inside the cabinet that effectively extracts fumes when connected to exhaust. Louvers are provided on the front doors to allow inward Low of fresh air.Zero-Corrosion: Full Polypropylene Body, with no exposed metal hardware, ensures there is no corrosionClosing mechanism: The cabinet has a latch to ensure proper shutting of the doors.Removable & Height- Adjustable PP Trays as Shelves: the PP Collection Trays can be removed easily, and can be height-adjusted as required.Load Bearing Capacity & Spill Containment: Each shelf can take up to 30 kgs (approx) of uniformly distributed load. The shelves are leak-proof and fully contain accidental spillages. Locking Provision: The door has provision for using a padlock to safeguard the contents of the cabinet. as directed by Engineer In-charge(As per specified in Technical specification of furniture Page No.30 of NIT) |
| 70 | Providing supply installation of Ss Emergency Safety Shower With Eye / Face Wash Complete Ss Construction as directed by Engineer In-charge(As per specified in Technical specification of furniture Page No.30 of NIT) |
| 71 | Providing, supplying and placing of Wall Mount Cabinet of 600 mm W x 320 mm D x 674 mm H Over head cabinets are to be Pure epoxy powder coated with thickness of 40-60 microns and should be fixed on the wall. The cabinet should have a corrosion resistance magnetic strip as shutter catch, shutters are to be equipped with 180 degree cam lock. PP constructed semi recessed handle to be screw fitted to the shutters. Hinges are to be of SS-304 knuckle overlay type with 270 degree opening and 2 nos of hinges are to be screw fitted to each shutter and cabinet.Unit Construction : It should be Welded body construction with load bearing members such as top, bottom and stiffeners should have a minimum thickness of 0.8 mm.Shelf : Should be made of 0.8mm thickness which should be adjustable to 6 steps of 50mm. Shutter should be over-closing type. It has a sandwich door construction with shutter front & shutter cover with 1.2mm thick hinge stiffener. Empty gap should with filled with 15mm thick paper honeycomb for sound dampening. as directed by Engineer In-charge(As per specified in Technical specification of furniture Page No.30 of NIT) |
| 72 | Providing supply installation of WALL TABLE - 3 2740mmL X 770mmD X 900mmH WITH ELECTRICAL TRUNKINGConstruction : Floor based Welded cabinet system having storage body should be flush face construction with intersection of vertical and horizontal members like LH and RH side panel along with front horizontal channel, back panel and bottom panel. It should be relocated anywhere easily as it is an independent unit. Cabinet should of square non-sharp edge construction. Doors should be assembled with SS-304 hinge assembly. Removable back panel should be provided to easily access the service lines running behind the cabinet benches. Intermediate horizontal channels should be provided between door and drawer. Toe-space of 90mm X 90mm is provided at front-bottom side of cabinet. Levelers are provided for easy leveling of welded cabinet. Shelf should be eight-bend panel with 20mm height. Drawer tray should be of single piece construction. Drawer should be well supported on LH and RH ball slide suspension system. Steel door and drawer front should be of double wall construction with sound dampening material filled inside. Doors should be easily removable and hinges should be easily replaceable. Knee space panel should be in 22 gauge construction. Cabinets are tested as per SEFA 8M standard from a SEFA approved Lab and also tested as per EN 14727 from a third party testing agencyDimensions: W=600 mm, 750 mm, 900mm , D = 530mm, H = 875 mm Configurations: continuous storages MOC: MSCRCA: IS – 513 (1994) Thickness: LH/RH side panels, shutter front, Bottom panel, Top front, Drawer separator, shelf, Alignment channel is of 1.2mm thk. Removable Back panel, Shutter cover, Fr. Rack strip, Top cover panel is of 0.8mmthk Finish: The complete M.S. material of cabinet should be pre-treated (degreased, Zinc phosphated) and epoxy powder coated for better corrosion resistance. The thickness of powder coat should be 45-50 microns, which passes the test of Salt Spray for 1000 hours. It should have a high temperature withstanding capacity with excellent electrical insulation properties.The rear portion of above accessories which is in contact with live metal should be made from thermo set material which will not melt on heating.Handle: Anodized Aluminum Recessed-Type, CTC: 160.0mm Lock: Units have a locking facility with 180° and 10 lever cam lock mechanism (except for sink and corner unit) Hinge: SS Hinge .Screw: SS 304.Shutter : should be of twin-type construction with sound dampening effect using profill. Shutter cover should be equipped with Bump on for sound dampening. Base Moulding should be made of PVC with corner clips. Ball Slide: 500mm Length Shutter should have provision of roller catch. COVER / FILLER PANELS All side cover panels and back panels, filler panels should be made from CRCA MS panels of 1.0mm thickness with pure epoxy powder coating . SERVICE FITTINGS AND ACCESSORIES Service fittings should be laboratory grade, and water faucets and valve bodies should be cast red brass alloy or bronze forgings, all fittings should be powder plated unless specified otherwise. Service Indexes: Fittings should be identified with service indexes in the color coding as per DIN 12920. ELECTRICAL ACCESSORIES (6/16 A SWITCHES & SOCKETS) : These are made of High gloss virgin grade engineering thermoplastics to impart a defect free surface. they impart excellent electrical insulation properties i.e. do not melt on heating or catches fire. Owing to this all electrical switches and sockets are capable of handling higher currents and operating temperatures. Front plates can be changed at any time with ease without disturbing the wiring to quickly and economically match changes in the surroundings.WORKTOP : Jet Black Granite: It should be 19mm (+/- 2mm) thick Jet Black Granite worktop. The exposed edges of the worktop should be chamfered and smoothened. The bottom of the worktop should be polished and there should be a V-groove throughout the length of the exposed edges to protect the cabinets from coming in contact with the spillages. The overhang on the storage cabinet is 25 mm at the front side and 30 mm at the sides. The backing material used is a neoprene mat of 6 mm thickness. as directed by Engineer In-charge(As per specified in Technical specification of furniture Page No.30 of NIT) |
| 73 | Providing supply installation of WALL TABLE - 3 4235mmL X 920mmD X 900mmH WITH ELECTRICAL TRUNKINGConstruction : Floor based Welded cabinet system having storage body should be flush face construction with intersection of vertical and horizontal members like LH and RH side panel along with front horizontal channel, back panel and bottom panel. It should be relocated anywhere easily as it is an independent unit. Cabinet should of square non-sharp edge construction. Doors should be assembled with SS-304 hinge assembly. Removable back panel should be provided to easily access the service lines running behind the cabinet benches. Intermediate horizontal channels should be provided between door and drawer. Toe-space of 90mm X 90mm is provided at front-bottom side of cabinet. Levelers are provided for easy leveling of welded cabinet. Shelf should be eight-bend panel with 20mm height. Drawer tray should be of single piece construction. Drawer should be well supported on LH and RH ball slide suspension system. Steel door and drawer front should be of double wall construction with sound dampening material filled inside. Doors should be easily removable and hinges should be easily replaceable. Knee space panel should be in 22 gauge construction. Cabinets are tested as per SEFA 8M standard from a SEFA approved Lab and also tested as per EN 14727 from a third party testing agencyDimensions: W=600 mm, 750 mm , D = 530mm, H = 875 mm Configurations: continuous storage MOC: MSCRCA: IS – 513 (1994) Thickness: LH/RH side panels, shutter front, Bottom panel, Top front, Drawer separator, shelf, Alignment channel is of 1.2mm thk. Removable Back panel, Shutter cover, Fr. Rack strip, Top cover panel is of 0.8mmthk Finish: The complete M.S. material of cabinet should be pre-treated (degreased, Zinc phosphated) and epoxy powder coated for better corrosion resistance. The thickness of powder coat should be 45-50 microns, which passes the test of Salt Spray for 1000 hours. It should have a high temperature withstanding capacity with excellent electrical insulation properties.The rear portion of above accessories which is in contact with live metal should be made from thermo set material which will not melt on heating.Handle: Anodized Aluminum Recessed-Type, CTC: 160.0mm Lock: Units have a locking facility with 180° and 10 lever cam lock mechanism (except for sink and corner unit) Hinge: SS Hinge .Screw: SS 304.Shutter : should be of twin-type construction with sound dampening effect using profill. Shutter cover should be equipped with Bump on for sound dampening. Base Moulding should be made of PVC with corner clips. Ball Slide: 500mm Length Shutter should have provision of roller catch. COVER / FILLER PANELS All side cover panels and back panels, filler panels should be made from CRCA MS panels of 1.0mm thickness with pure epoxy powder coating . SERVICE FITTINGS AND ACCESSORIES Service fittings should be laboratory grade, and water faucets and valve bodies should be cast red brass alloy or bronze forgings, all fittings should be powder plated unless specified otherwise. Service Indexes: Fittings should be identified with service indexes in the color coding as per DIN 12920. PP Sink,Polypropylene Molded Sinks: Made up of 5 mm thick high density and elastic poly propylene with good resistance to organic solvents. Sink - Bowl size to be a minimum of (L x W x D) 560 x 355 x 300 mm. -1 Nos Faucet - 3-way type faucet as per approved make 1 Nos ELECTRICAL ACCESSORIES (6/16 A SWITCHES & SOCKETS) : These are made of High gloss virgin grade engineering thermoplastics to impart a defect free surface. they impart excellent electrical insulation properties i.e. do not melt on heating or catches fire. Owing to this all electrical switches and sockets are capable of handling higher currents and operating temperatures. Front plates can be changed at any time with ease without disturbing the wiring to quickly and economically match changes in the surroundings.WORKTOP : Jet Black Granite: It should be 19mm (+/- 2mm) thick Jet Black Granite worktop. The exposed edges of the worktop should be chamfered and smoothened. The bottom of the worktop should be polished and there should be a V-groove throughout the length of the exposed edges to protect the cabinets from coming in contact with the spillages. The overhang on the storage cabinet is 25 mm at the front side and 30 mm at the sides. The backing material used is a neoprene mat of 6 mm thickness. as directed by Engineer In-charge(As per specified in Technical specification of furniture Page No.30 of NIT) |
| 74 | Providing supply installation of WALL TABLE - 3 4540mmL X 920mmD X 900mmH WITH ELECTRICAL TRUNKINGConstruction : Floor based Welded cabinet system having storage body should be flush face construction with intersection of vertical and horizontal members like LH and RH side panel along with front horizontal channel, back panel and bottom panel. It should be relocated anywhere easily as it is an independent unit. Cabinet should of square non-sharp edge construction. Doors should be assembled with SS-304 hinge assembly. Removable back panel should be provided to easily access the service lines running behind the cabinet benches. Intermediate horizontal channels should be provided between door and drawer. Toe-space of 90mm X 90mm is provided at front-bottom side of cabinet. Levelers are provided for easy leveling of welded cabinet. Shelf should be eight-bend panel with 20mm height. Drawer tray should be of single piece construction. Drawer should be well supported on LH and RH ball slide suspension system. Steel door and drawer front should be of double wall construction with sound dampening material filled inside. Doors should be easily removable and hinges should be easily replaceable. Knee space panel should be in 22 gauge construction. Cabinets are tested as per SEFA 8M standard from a SEFA approved Lab and also tested as per EN 14727 from a third party testing agencyDimensions: W=600 mm, 750 mm, 900mm , D = 530mm, H = 875 mm Configurations: continuous storages MOC: MSCRCA: IS – 513 (1994) Thickness: LH/RH side panels, shutter front, Bottom panel, Top front, Drawer separator, shelf, Alignment channel is of 1.2mm thk. Removable Back panel, Shutter cover, Fr. Rack strip, Top cover panel is of 0.8mmthk Finish: The complete M.S. material of cabinet should be pre-treated (degreased, Zinc phosphated) and epoxy powder coated for better corrosion resistance. The thickness of powder coat should be 45-50 microns, which passes the test of Salt Spray for 1000 hours. It should have a high temperature withstanding capacity with excellent electrical insulation properties.The rear portion of above accessories which is in contact with live metal should be made from thermo set material which will not melt on heating.Handle: Anodized Aluminum Recessed-Type, CTC: 160.0mm Lock: Units have a locking facility with 180° and 10 lever cam lock mechanism (except for sink and corner unit) Hinge: SS Hinge .Screw: SS 304.Shutter : should be of twin-type construction with sound dampening effect using profill. Shutter cover should be equipped with Bump on for sound dampening. Base Moulding should be made of PVC with corner clips. Ball Slide: 500mm Length Shutter should have provision of roller catch. COVER / FILLER PANELS All side cover panels and back panels, filler panels should be made from CRCA MS panels of 1.0mm thickness with pure epoxy powder coating . SERVICE FITTINGS AND ACCESSORIES Service fittings should be laboratory grade, and water faucets and valve bodies should be cast red brass alloy or bronze forgings, all fittings should be powder plated unless specified otherwise. Service Indexes: Fittings should be identified with service indexes in the color coding as per DIN 12920. ELECTRICAL ACCESSORIES (6/16 A SWITCHES & SOCKETS) : These are made of High gloss virgin grade engineering thermoplastics to impart a defect free surface. they impart excellent electrical insulation properties i.e. do not melt on heating or catches fire. Owing to this all electrical switches and sockets are capable of handling higher currents and operating temperatures. Front plates can be changed at any time with ease without disturbing the wiring to quickly and economically match changes in the surroundings.WORKTOP : Jet Black Granite: It should be 19mm (+/- 2mm) thick Jet Black Granite worktop. The exposed edges of the worktop should be chamfered and smoothened. The bottom of the worktop should be polished and there should be a V-groove throughout the length of the exposed edges to protect the cabinets from coming in contact with the spillages. The overhang on the storage cabinet is 25 mm at the front side and 30 mm at the sides. The backing material used is a neoprene mat of 6 mm thickness. as directed by Engineer In-charge(As per specified in Technical specification of furniture Page No.30 of NIT) |
| 75 | Providing supply installation of WALL TABLE - 3 7965mmL X 920mmD X 900mmH WITH ELECTRICAL TRUNKINGConstruction : Floor based Welded cabinet system having storage body should be flush face construction with intersection of vertical and horizontal members like LH and RH side panel along with front horizontal channel, back panel and bottom panel. It should be relocated anywhere easily as it is an independent unit. Cabinet should of square non-sharp edge construction. Doors should be assembled with SS-304 hinge assembly. Removable back panel should be provided to easily access the service lines running behind the cabinet benches. Intermediate horizontal channels should be provided between door and drawer. Toe-space of 90mm X 90mm is provided at front-bottom side of cabinet. Levelers are provided for easy leveling of welded cabinet. Shelf should be eight-bend panel with 20mm height. Drawer tray should be of single piece construction. Drawer should be well supported on LH and RH ball slide suspension system. Steel door and drawer front should be of double wall construction with sound dampening material filled inside. Doors should be easily removable and hinges should be easily replaceable. Knee space panel should be in 22 gauge construction. Cabinets are tested as per SEFA 8M standard from a SEFA approved Lab and also tested as per EN 14727 from a third party testing agencyDimensions: W=600 mm, 750 mm, 900mm , D = 530mm, H = 875 mm Configurations:Continuous storage MOC: MSCRCA: IS – 513 (1994) Thickness: LH/RH side panels, shutter front, Bottom panel, Top front, Drawer separator, shelf, Alignment channel is of 1.2mm thk. Removable Back panel, Shutter cover, Fr. Rack strip, Top cover panel is of 0.8mmthk Finish: The complete M.S. material of cabinet should be pre-treated (degreased, Zinc phosphated) and epoxy powder coated for better corrosion resistance. The thickness of powder coat should be 45-50 microns, which passes the test of Salt Spray for 1000 hours. It should have a high temperature withstanding capacity with excellent electrical insulation properties.The rear portion of above accessories which is in contact with live metal should be made from thermo set material which will not melt on heating.Handle: Anodized Aluminum Recessed-Type, CTC: 160.0mm Lock: Units have a locking facility with 180° and 10 lever cam lock mechanism (except for sink and corner unit) Hinge: SS Hinge .Screw: SS 304.Shutter : should be of twin-type construction with sound dampening effect using profill. Shutter cover should be equipped with Bump on for sound dampening. Base Moulding should be made of PVC with corner clips. Ball Slide: 500mm Length Shutter should have provision of roller catch. COVER / FILLER PANELS All side cover panels and back panels, filler panels should be made from CRCA MS panels of 1.0mm thickness with pure epoxy powder coating . SERVICE FITTINGS AND ACCESSORIES Service fittings should be laboratory grade, and water faucets and valve bodies should be cast red brass alloy or bronze forgings, all fittings should be powder plated unless specified otherwise. Service Indexes: Fittings should be identified with service indexes in the color coding as per DIN 12920. ELECTRICAL ACCESSORIES (6/16 A SWITCHES & SOCKETS) : These are made of High gloss virgin grade engineering thermoplastics to impart a defect free surface. they impart excellent electrical insulation properties i.e. do not melt on heating or catches fire. Owing to this all electrical switches and sockets are capable of handling higher currents and operating temperatures. Front plates can be changed at any time with ease without disturbing the wiring to quickly and economically match changes in the surroundings.WORKTOP : Jet Black Granite: It should be 19mm (+/- 2mm) thick Jet Black Granite worktop. The exposed edges of the worktop should be chamfered and smoothened. The bottom of the worktop should be polished and there should be a V-groove throughout the length of the exposed edges to protect the cabinets from coming in contact with the spillages. The overhang on the storage cabinet is 25 mm at the front side and 30 mm at the sides. The backing material used is a neoprene mat of 6 mm thickness. as directed by Engineer In-charge(As per specified in Technical specification of furniture Page No.30 of NIT) |
| 76 | Providing supply installation of WALL TABLE - 3 8115mmL X 770mmD X 900mmH WITH ELECTRICAL TRUNKINGConstruction : Floor based Welded cabinet system having storage body should be flush face construction with intersection of vertical and horizontal members like LH and RH side panel along with front horizontal channel, back panel and bottom panel. It should be relocated anywhere easily as it is an independent unit. Cabinet should of square non-sharp edge construction. Doors should be assembled with SS-304 hinge assembly. Removable back panel should be provided to easily access the service lines running behind the cabinet benches. Intermediate horizontal channels should be provided between door and drawer. Toe-space of 90mm X 90mm is provided at front-bottom side of cabinet. Levelers are provided for easy leveling of welded cabinet. Shelf should be eight-bend panel with 20mm height. Drawer tray should be of single piece construction. Drawer should be well supported on LH and RH ball slide suspension system. Steel door and drawer front should be of double wall construction with sound dampening material filled inside. Doors should be easily removable and hinges should be easily replaceable. Knee space panel should be in 22 gauge construction. Cabinets are tested as per SEFA 8M standard from a SEFA approved Lab and also tested as per EN 14727 from a third party testing agencyDimensions: W=600 mm, 750 mm, 900mm , D = 530mm, H = 875 mm Configurations:Continuous storage MOC: MSCRCA: IS – 513 (1994) Thickness: LH/RH side panels, shutter front, Bottom panel, Top front, Drawer separator, shelf, Alignment channel is of 1.2mm thk. Removable Back panel, Shutter cover, Fr. Rack strip, Top cover panel is of 0.8mmthk Finish: The complete M.S. material of cabinet should be pre-treated (degreased, Zinc phosphated) and epoxy powder coated for better corrosion resistance. The thickness of powder coat should be 45-50 microns, which passes the test of Salt Spray for 1000 hours. It should have a high temperature withstanding capacity with excellent electrical insulation properties.The rear portion of above accessories which is in contact with live metal should be made from thermo set material which will not melt on heating.Handle: Anodized Aluminum Recessed-Type, CTC: 160.0mm Lock: Units have a locking facility with 180° and 10 lever cam lock mechanism (except for sink and corner unit) Hinge: SS Hinge .Screw: SS 304.Shutter : should be of twin-type construction with sound dampening effect using profill. Shutter cover should be equipped with Bump on for sound dampening. Base Moulding should be made of PVC with corner clips. Ball Slide: 500mm Length Shutter should have provision of roller catch. COVER / FILLER PANELS All side cover panels and back panels, filler panels should be made from CRCA MS panels of 1.0mm thickness with pure epoxy powder coating . SERVICE FITTINGS AND ACCESSORIES Service fittings should be laboratory grade, and water faucets and valve bodies should be cast red brass alloy or bronze forgings, all fittings should be powder plated unless specified otherwise. Service Indexes: Fittings should be identified with service indexes in the color coding as per DIN 12920. ELECTRICAL ACCESSORIES (6/16 A SWITCHES & SOCKETS) : These are made of High gloss virgin grade engineering thermoplastics to impart a defect free surface. they impart excellent electrical insulation properties i.e. do not melt on heating or catches fire. Owing to this all electrical switches and sockets are capable of handling higher currents and operating temperatures. Front plates can be changed at any time with ease without disturbing the wiring to quickly and economically match changes in the surroundings.WORKTOP : Jet Black Granite: It should be 19mm (+/- 2mm) thick Jet Black Granite worktop. The exposed edges of the worktop should be chamfered and smoothened. The bottom of the worktop should be polished and there should be a V-groove throughout the length of the exposed edges to protect the cabinets from coming in contact with the spillages. The overhang on the storage cabinet is 25 mm at the front side and 30 mm at the sides. The backing material used is a neoprene mat of 6 mm thickness. as directed by Engineer In-charge(As per specified in Technical specification of furniture Page No.30 of NIT) |
| 77 | Providing supply installation of WALL TABLE - 1 2740mmL X 770mmD X 900mmH WITH ELECTRICAL TRUNKINGConstruction : Floor based Welded cabinet system having storage body should be flush face construction with intersection of vertical and horizontal members like LH and RH side panel along with front horizontal channel, back panel and bottom panel. It should be relocated anywhere easily as it is an independent unit. Cabinet should of square non-sharp edge construction. Doors should be assembled with SS-304 hinge assembly. Removable back panel should be provided to easily access the service lines running behind the cabinet benches. Intermediate horizontal channels should be provided between door and drawer. Toe-space of 90mm X 90mm is provided at front-bottom side of cabinet. Levelers are provided for easy leveling of welded cabinet. Shelf should be eight-bend panel with 20mm height. Drawer tray should be of single piece construction. Drawer should be well supported on LH and RH ball slide suspension system. Steel door and drawer front should be of double wall construction with sound dampening material filled inside. Doors should be easily removable and hinges should be easily replaceable. Knee space panel should be in 22 gauge construction. Cabinets are tested as per SEFA 8M standard from a SEFA approved Lab and also tested as per EN 14727 from a third party testing agencyDimensions: W=600 mm, 750 mm, 900mm , D = 530mm, H = 875 mm Configurations:Continuous storage MOC: MSCRCA: IS – 513 (1994) Thickness: LH/RH side panels, shutter front, Bottom panel, Top front, Drawer separator, shelf, Alignment channel is of 1.2mm thk. Removable Back panel, Shutter cover, Fr. Rack strip, Top cover panel is of 0.8mmthk Finish: The complete M.S. material of cabinet should be pre-treated (degreased, Zinc phosphated) and epoxy powder coated for better corrosion resistance. The thickness of powder coat should be 45-50 microns, which passes the test of Salt Spray for 1000 hours. It should have a high temperature withstanding capacity with excellent electrical insulation properties.The rear portion of above accessories which is in contact with live metal should be made from thermo set material which will not melt on heating.Handle: Anodized Aluminum Recessed-Type, CTC: 160.0mm Lock: Units have a locking facility with 180° and 10 lever cam lock mechanism (except for sink and corner unit) Hinge: SS Hinge .Screw: SS 304.Shutter : should be of twin-type construction with sound dampening effect using profill. Shutter cover should be equipped with Bump on for sound dampening. Base Moulding should be made of PVC with corner clips. Ball Slide: 500mm Length Shutter should have provision of roller catch. COVER / FILLER PANELS All side cover panels and back panels, filler panels should be made from CRCA MS panels of 1.0mm thickness with pure epoxy powder coating . SERVICE FITTINGS AND ACCESSORIES Service fittings should be laboratory grade, and water faucets and valve bodies should be cast red brass alloy or bronze forgings, all fittings should be powder plated unless specified otherwise. Service Indexes: Fittings should be identified with service indexes in the color coding as per DIN 12920. ELECTRICAL ACCESSORIES (6/16 A SWITCHES & SOCKETS) : These are made of High gloss virgin grade engineering thermoplastics to impart a defect free surface. they impart excellent electrical insulation properties i.e. do not melt on heating or catches fire. Owing to this all electrical switches and sockets are capable of handling higher currents and operating temperatures. Front plates can be changed at any time with ease without disturbing the wiring to quickly and economically match changes in the surroundings.WORKTOP : Jet Black Granite: It should be 19mm (+/- 2mm) thick Jet Black Granite worktop. The exposed edges of the worktop should be chamfered and smoothened. The bottom of the worktop should be polished and there should be a V-groove throughout the length of the exposed edges to protect the cabinets from coming in contact with the spillages. The overhang on the storage cabinet is 25 mm at the front side and 30 mm at the sides. The backing material used is a neoprene mat of 6 mm thickness. as directed by Engineer In-charge(As per specified in Technical specification of furniture Page No.30 of NIT) |
| 78 | Providing supply installation of WALL TABLE - 1 2890mmL X 920mmD X 900mmH WITH ELECTRICAL TRUNKINGConstruction : Floor based Welded cabinet system having storage body should be flush face construction with intersection of vertical and horizontal members like LH and RH side panel along with front horizontal channel, back panel and bottom panel. It should be relocated anywhere easily as it is an independent unit. Cabinet should of square non-sharp edge construction. Doors should be assembled with SS-304 hinge assembly. Removable back panel should be provided to easily access the service lines running behind the cabinet benches. Intermediate horizontal channels should be provided between door and drawer. Toe-space of 90mm X 90mm is provided at front-bottom side of cabinet. Levelers are provided for easy leveling of welded cabinet. Shelf should be eight-bend panel with 20mm height. Drawer tray should be of single piece construction. Drawer should be well supported on LH and RH ball slide suspension system. Steel door and drawer front should be of double wall construction with sound dampening material filled inside. Doors should be easily removable and hinges should be easily replaceable. Knee space panel should be in 22 gauge construction. Cabinets are tested as per SEFA 8M standard from a SEFA approved Lab and also tested as per EN 14727 from a third party testing agencyDimensions: W=600 mm, 750 mm, 900mm , D = 530mm, H = 875 mm Configurations:Continuous storage MOC: MSCRCA: IS – 513 (1994) Thickness: LH/RH side panels, shutter front, Bottom panel, Top front, Drawer separator, shelf, Alignment channel is of 1.2mm thk. Removable Back panel, Shutter cover, Fr. Rack strip, Top cover panel is of 0.8mmthk Finish: The complete M.S. material of cabinet should be pre-treated (degreased, Zinc phosphated) and epoxy powder coated for better corrosion resistance. The thickness of powder coat should be 45-50 microns, which passes the test of Salt Spray for 1000 hours. It should have a high temperature withstanding capacity with excellent electrical insulation properties.The rear portion of above accessories which is in contact with live metal should be made from thermo set material which will not melt on heating.Handle: Anodized Aluminum Recessed-Type, CTC: 160.0mm Lock: Units have a locking facility with 180° and 10 lever cam lock mechanism (except for sink and corner unit) Hinge: SS Hinge .Screw: SS 304.Shutter : should be of twin-type construction with sound dampening effect using profill. Shutter cover should be equipped with Bump on for sound dampening. Base Moulding should be made of PVC with corner clips. Ball Slide: 500mm Length Shutter should have provision of roller catch. COVER / FILLER PANELS All side cover panels and back panels, filler panels should be made from CRCA MS panels of 1.0mm thickness with pure epoxy powder coating . SERVICE FITTINGS AND ACCESSORIES Service fittings should be laboratory grade, and water faucets and valve bodies should be cast red brass alloy or bronze forgings, all fittings should be powder plated unless specified otherwise. Service Indexes: Fittings should be identified with service indexes in the color coding as per DIN 12920. ELECTRICAL ACCESSORIES (6/16 A SWITCHES & SOCKETS) : These are made of High gloss virgin grade engineering thermoplastics to impart a defect free surface. they impart excellent electrical insulation properties i.e. do not melt on heating or catches fire. Owing to this all electrical switches and sockets are capable of handling higher currents and operating temperatures. Front plates can be changed at any time with ease without disturbing the wiring to quickly and economically match changes in the surroundings.WORKTOP : Jet Black Granite: It should be 19mm (+/- 2mm) thick Jet Black Granite worktop. The exposed edges of the worktop should be chamfered and smoothened. The bottom of the worktop should be polished and there should be a V-groove throughout the length of the exposed edges to protect the cabinets from coming in contact with the spillages. The overhang on the storage cabinet is 25 mm at the front side and 30 mm at the sides. The backing material used is a neoprene mat of 6 mm thickness. as directed by Engineer In-charge(As per specified in Technical specification of furniture Page No.30 of NIT) |
| 79 | Providing supply installation of WALL TABLE - 1 3940mmL X 770mmD X 900mmH WITH ELECTRICAL TRUNKINGConstruction : Floor based Welded cabinet system having storage body should be flush face construction with intersection of vertical and horizontal members like LH and RH side panel along with front horizontal channel, back panel and bottom panel. It should be relocated anywhere easily as it is an independent unit. Cabinet should of square non-sharp edge construction. Doors should be assembled with SS-304 hinge assembly. Removable back panel should be provided to easily access the service lines running behind the cabinet benches. Intermediate horizontal channels should be provided between door and drawer. Toe-space of 90mm X 90mm is provided at front-bottom side of cabinet. Levelers are provided for easy leveling of welded cabinet. Shelf should be eight-bend panel with 20mm height. Drawer tray should be of single piece construction. Drawer should be well supported on LH and RH ball slide suspension system. Steel door and drawer front should be of double wall construction with sound dampening material filled inside. Doors should be easily removable and hinges should be easily replaceable. Knee space panel should be in 22 gauge construction. Cabinets are tested as per SEFA 8M standard from a SEFA approved Lab and also tested as per EN 14727 from a third party testing agencyDimensions: W=600 mm, 750 mm, 900mm , D = 530mm, H = 875 mm Configurations:Continuous storage MOC: MSCRCA: IS – 513 (1994) Thickness: LH/RH side panels, shutter front, Bottom panel, Top front, Drawer separator, shelf, Alignment channel is of 1.2mm thk. Removable Back panel, Shutter cover, Fr. Rack strip, Top cover panel is of 0.8mmthk Finish: The complete M.S. material of cabinet should be pre-treated (degreased, Zinc phosphated) and epoxy powder coated for better corrosion resistance. The thickness of powder coat should be 45-50 microns, which passes the test of Salt Spray for 1000 hours. It should have a high temperature withstanding capacity with excellent electrical insulation properties.The rear portion of above accessories which is in contact with live metal should be made from thermo set material which will not melt on heating.Handle: Anodized Aluminum Recessed-Type, CTC: 160.0mm Lock: Units have a locking facility with 180° and 10 lever cam lock mechanism (except for sink and corner unit) Hinge: SS Hinge .Screw: SS 304.Shutter : should be of twin-type construction with sound dampening effect using profill. Shutter cover should be equipped with Bump on for sound dampening. Base Moulding should be made of PVC with corner clips. Ball Slide: 500mm Length Shutter should have provision of roller catch. COVER / FILLER PANELS All side cover panels and back panels, filler panels should be made from CRCA MS panels of 1.0mm thickness with pure epoxy powder coating . SERVICE FITTINGS AND ACCESSORIES Service fittings should be laboratory grade, and water faucets and valve bodies should be cast red brass alloy or bronze forgings, all fittings should be powder plated unless specified otherwise. Service Indexes: Fittings should be identified with service indexes in the color coding as per DIN 12920. ELECTRICAL ACCESSORIES (6/16 A SWITCHES & SOCKETS) : These are made of High gloss virgin grade engineering thermoplastics to impart a defect free surface. they impart excellent electrical insulation properties i.e. do not melt on heating or catches fire. Owing to this all electrical switches and sockets are capable of handling higher currents and operating temperatures. Front plates can be changed at any time with ease without disturbing the wiring to quickly and economically match changes in the surroundings.WORKTOP : Jet Black Granite: It should be 19mm (+/- 2mm) thick Jet Black Granite worktop. The exposed edges of the worktop should be chamfered and smoothened. The bottom of the worktop should be polished and there should be a V-groove throughout the length of the exposed edges to protect the cabinets from coming in contact with the spillages. The overhang on the storage cabinet is 25 mm at the front side and 30 mm at the sides. The backing material used is a neoprene mat of 6 mm thickness. as directed by Engineer In-charge(As per specified in Technical specification of furniture Page No.30 of NIT) |
| 80 | Providing supply installation of WALL TABLE - 1 7385mmL X 770mmD X 900mmH WITH ELECTRICAL TRUNKING , LPG VALVEConstruction : Floor based Welded cabinet system having storage body should be flush face construction with intersection of vertical and horizontal members like LH and RH side panel along with front horizontal channel, back panel and bottom panel. It should be relocated anywhere easily as it is an independent unit. Cabinet should of square non-sharp edge construction. Doors should be assembled with SS-304 hinge assembly. Removable back panel should be provided to easily access the service lines running behind the cabinet benches. Intermediate horizontal channels should be provided between door and drawer. Toe-space of 90mm X 90mm is provided at front-bottom side of cabinet. Levelers are provided for easy leveling of welded cabinet. Shelf should be eight-bend panel with 20mm height. Drawer tray should be of single piece construction. Drawer should be well supported on LH and RH ball slide suspension system. Steel door and drawer front should be of double wall construction with sound dampening material filled inside. Doors should be easily removable and hinges should be easily replaceable. Knee space panel should be in 22 gauge construction. Cabinets are tested as per SEFA 8M standard from a SEFA approved Lab and also tested as per EN 14727 from a third party testing agencyDimensions: W=600 mm, 750 mm, 900mm , D = 530mm, H = 875 mm Configurations: continuous storages MOC: MSCRCA: IS – 513 (1994) Thickness: LH/RH side panels, shutter front, Bottom panel, Top front, Drawer separator, shelf, Alignment channel is of 1.2mm thk. Removable Back panel, Shutter cover, Fr. Rack strip, Top cover panel is of 0.8mmthk Finish: The complete M.S. material of cabinet should be pre-treated (degreased, Zinc phosphated) and epoxy powder coated for better corrosion resistance. The thickness of powder coat should be 45-50 microns, which passes the test of Salt Spray for 1000 hours. It should have a high temperature withstanding capacity with excellent electrical insulation properties.The rear portion of above accessories which is in contact with live metal should be made from thermo set material which will not melt on heating.Handle: Anodized Aluminum Recessed-Type, CTC: 160.0mm Lock: Units have a locking facility with 180° and 10 lever cam lock mechanism (except for sink and corner unit) Hinge: SS Hinge .Screw: SS 304.Shutter : should be of twin-type construction with sound dampening effect using profill. Shutter cover should be equipped with Bump on for sound dampening. Base Moulding should be made of PVC with corner clips. Ball Slide: 500mm Length Shutter should have provision of roller catch. COVER / FILLER PANELS All side cover panels and back panels, filler panels should be made from CRCA MS panels of 1.0mm thickness with pure epoxy powder coating . SERVICE FITTINGS AND ACCESSORIES Service fittings should be laboratory grade, and water faucets and valve bodies should be cast red brass alloy or bronze forgings, all fittings should be powder plated unless specified otherwise. Service Indexes: Fittings should be identified with service indexes in the color coding as per DIN 12920. ELECTRICAL ACCESSORIES (6/16 A SWITCHES & SOCKETS) : These are made of High gloss virgin grade engineering thermoplastics to impart a defect free surface. they impart excellent electrical insulation properties i.e. do not melt on heating or catches fire. Owing to this all electrical switches and sockets are capable of handling higher currents and operating temperatures. Front plates can be changed at any time with ease without disturbing the wiring to quickly and economically match changes in the surroundings.WORKTOP : Jet Black Granite: It should be 19mm (+/- 2mm) thick Jet Black Granite worktop. The exposed edges of the worktop should be chamfered and smoothened. The bottom of the worktop should be polished and there should be a V-groove throughout the length of the exposed edges to protect the cabinets from coming in contact with the spillages. The overhang on the storage cabinet is 25 mm at the front side and 30 mm at the sides. The backing material used is a neoprene mat of 6 mm thickness. as directed by Engineer In-charge(As per specified in Technical specification of furniture Page No.30 of NIT) |
| 81 | Providing supply installation of WALL TABLE - 1 7540mmL X 770mmD X 900mmH WITH ELECTRICAL TRUNKINGConstruction : Floor based Welded cabinet system having storage body should be flush face construction with intersection of vertical and horizontal members like LH and RH side panel along with front horizontal channel, back panel and bottom panel. It should be relocated anywhere easily as it is an independent unit. Cabinet should of square non-sharp edge construction. Doors should be assembled with SS-304 hinge assembly. Removable back panel should be provided to easily access the service lines running behind the cabinet benches. Intermediate horizontal channels should be provided between door and drawer. Toe-space of 90mm X 90mm is provided at front-bottom side of cabinet. Levelers are provided for easy leveling of welded cabinet. Shelf should be eight-bend panel with 20mm height. Drawer tray should be of single piece construction. Drawer should be well supported on LH and RH ball slide suspension system. Steel door and drawer front should be of double wall construction with sound dampening material filled inside. Doors should be easily removable and hinges should be easily replaceable. Knee space panel should be in 22 gauge construction. Cabinets are tested as per SEFA 8M standard from a SEFA approved Lab and also tested as per EN 14727 from a third party testing agencyDimensions: W=600 mm, 750 mm, 900mm , D = 530mm, H = 875 mm Configurations: continuous storages MOC: MSCRCA: IS – 513 (1994) Thickness: LH/RH side panels, shutter front, Bottom panel, Top front, Drawer separator, shelf, Alignment channel is of 1.2mm thk. Removable Back panel, Shutter cover, Fr. Rack strip, Top cover panel is of 0.8mmthk Finish: The complete M.S. material of cabinet should be pre-treated (degreased, Zinc phosphated) and epoxy powder coated for better corrosion resistance. The thickness of powder coat should be 45-50 microns, which passes the test of Salt Spray for 1000 hours. It should have a high temperature withstanding capacity with excellent electrical insulation properties.The rear portion of above accessories which is in contact with live metal should be made from thermo set material which will not melt on heating.Handle: Anodized Aluminum Recessed-Type, CTC: 160.0mm Lock: Units have a locking facility with 180° and 10 lever cam lock mechanism (except for sink and corner unit) Hinge: SS Hinge .Screw: SS 304.Shutter : should be of twin-type construction with sound dampening effect using profill. Shutter cover should be equipped with Bump on for sound dampening. Base Moulding should be made of PVC with corner clips. Ball Slide: 500mm Length Shutter should have provision of roller catch. COVER / FILLER PANELS All side cover panels and back panels, filler panels should be made from CRCA MS panels of 1.0mm thickness with pure epoxy powder coating . SERVICE FITTINGS AND ACCESSORIES Service fittings should be laboratory grade, and water faucets and valve bodies should be cast red brass alloy or bronze forgings, all fittings should be powder plated unless specified otherwise. Service Indexes: Fittings should be identified with service indexes in the color coding as per DIN 12920. ELECTRICAL ACCESSORIES (6/16 A SWITCHES & SOCKETS) : These are made of High gloss virgin grade engineering thermoplastics to impart a defect free surface. they impart excellent electrical insulation properties i.e. do not melt on heating or catches fire. Owing to this all electrical switches and sockets are capable of handling higher currents and operating temperatures. Front plates can be changed at any time with ease without disturbing the wiring to quickly and economically match changes in the surroundings.WORKTOP : Jet Black Granite: It should be 19mm (+/- 2mm) thick Jet Black Granite worktop. The exposed edges of the worktop should be chamfered and smoothened. The bottom of the worktop should be polished and there should be a V-groove throughout the length of the exposed edges to protect the cabinets from coming in contact with the spillages. The overhang on the storage cabinet is 25 mm at the front side and 30 mm at the sides. The backing material used is a neoprene mat of 6 mm thickness. as directed by Engineer In-charge (As per specified in Technical specification of furniture Page No.30 of NIT) |
| 82 | Providing supply installation of WALL TABLE - 1 WITH SINK 5385mmL X 770mmD X 900mmH WITH ELECTRICAL TRUNKINGConstruction : Floor based Welded cabinet system having storage body should be flush face construction with intersection of vertical and horizontal members like LH and RH side panel along with front horizontal channel, back panel and bottom panel. It should be relocated anywhere easily as it is an independent unit. Cabinet should of square non-sharp edge construction. Doors should be assembled with SS-304 hinge assembly. Removable back panel should be provided to easily access the service lines running behind the cabinet benches. Intermediate horizontal channels should be provided between door and drawer. Toe-space of 90mm X 90mm is provided at front-bottom side of cabinet. Levelers are provided for easy leveling of welded cabinet. Shelf should be eight-bend panel with 20mm height. Drawer tray should be of single piece construction. Drawer should be well supported on LH and RH ball slide suspension system. Steel door and drawer front should be of double wall construction with sound dampening material filled inside. Doors should be easily removable and hinges should be easily replaceable. Knee space panel should be in 22 gauge construction. Cabinets are tested as per SEFA 8M standard from a SEFA approved Lab and also tested as per EN 14727 from a third party testing agencyDimensions: W=600 mm, 750 mm, 900mm , D = 530mm, H = 875 mm Configurations:Continuous storage MOC: MSCRCA: IS – 513 (1994) Thickness: LH/RH side panels, shutter front, Bottom panel, Top front, Drawer separator, shelf, Alignment channel is of 1.2mm thk. Removable Back panel, Shutter cover, Fr. Rack strip, Top cover panel is of 0.8mmthk Finish: The complete M.S. material of cabinet should be pre-treated (degreased, Zinc phosphated) and epoxy powder coated for better corrosion resistance. The thickness of powder coat should be 45-50 microns, which passes the test of Salt Spray for 1000 hours. It should have a high temperature withstanding capacity with excellent electrical insulation properties.The rear portion of above accessories which is in contact with live metal should be made from thermo set material which will not melt on heating.Handle: Anodized Aluminum Recessed-Type, CTC: 160.0mm Lock: Units have a locking facility with 180° and 10 lever cam lock mechanism (except for sink and corner unit) Hinge: SS Hinge .Screw: SS 304.Shutter : should be of twin-type construction with sound dampening effect using profill. Shutter cover should be equipped with Bump on for sound dampening. Base Moulding should be made of PVC with corner clips. Ball Slide: 500mm Length Shutter should have provision of roller catch. COVER / FILLER PANELS All side cover panels and back panels, filler panels should be made from CRCA MS panels of 1.0mm thickness with pure epoxy powder coating . SERVICE FITTINGS AND ACCESSORIES Service fittings should be laboratory grade, and water faucets and valve bodies should be cast red brass alloy or bronze forgings, all fittings should be powder plated unless specified otherwise. Service Indexes: Fittings should be identified with service indexes in the color coding as per DIN 12920. ELECTRICAL ACCESSORIES (6/16 A SWITCHES & SOCKETS) : These are made of High gloss virgin grade engineering thermoplastics to impart a defect free surface. they impart excellent electrical insulation properties i.e. do not melt on heating or catches fire. Owing to this all electrical switches and sockets are capable of handling higher currents and operating temperatures. Front plates can be changed at any time with ease without disturbing the wiring to quickly and economically match changes in the surroundings.WORKTOP : Jet Black Granite: It should be 19mm (+/- 2mm) thick Jet Black Granite worktop. The exposed edges of the worktop should be chamfered and smoothened. The bottom of the worktop should be polished and there should be a V-groove throughout the length of the exposed edges to protect the cabinets from coming in contact with the spillages. The overhang on the storage cabinet is 25 mm at the front side and 30 mm at the sides. The backing material used is a neoprene mat of 6 mm thickness. as directed by Engineer In-charge (As per specified in Technical specification of furniture Page No.30 of NIT) |
| 83 | Providing supply installation of WALL TABLE - 1 WITH SINK 5735mmL X 920mmD X 900mmH WITH ELECTRICAL TRUNKING Construction : Floor based Welded cabinet system having storage body should be flush face construction with intersection of vertical and horizontal members like LH and RH side panel along with front horizontal channel, back panel and bottom panel. It should be relocated anywhere easily as it is an independent unit. Cabinet should of square non-sharp edge construction. Doors should be assembled with SS-304 hinge assembly. Removable back panel should be provided to easily access the service lines running behind the cabinet benches. Intermediate horizontal channels should be provided between door and drawer. Toe-space of 90mm X 90mm is provided at front-bottom side of cabinet. Levelers are provided for easy leveling of welded cabinet. Shelf should be eight-bend panel with 20mm height. Drawer tray should be of single piece construction. Drawer should be well supported on LH and RH ball slide suspension system. Steel door and drawer front should be of double wall construction with sound dampening material filled inside. Doors should be easily removable and hinges should be easily replaceable. Knee space panel should be in 22 gauge construction. Cabinets are tested as per SEFA 8M standard from a SEFA approved Lab and also tested as per EN 14727 from a third party testing agencyDimensions: W=600 mm, 750 mm , D = 530mm, H = 875 mm Configurations: continuous storage MOC: MSCRCA: IS – 513 (1994) Thickness: LH/RH side panels, shutter front, Bottom panel, Top front, Drawer separator, shelf, Alignment channel is of 1.2mm thk. Removable Back panel, Shutter cover, Fr. Rack strip, Top cover panel is of 0.8mmthk Finish: The complete M.S. material of cabinet should be pre-treated (degreased, Zinc phosphated) and epoxy powder coated for better corrosion resistance. The thickness of powder coat should be 45-50 microns, which passes the test of Salt Spray for 1000 hours. It should have a high temperature withstanding capacity with excellent electrical insulation properties.The rear portion of above accessories which is in contact with live metal should be made from thermo set material which will not melt on heating.Handle: Anodized Aluminum Recessed-Type, CTC: 160.0mm Lock: Units have a locking facility with 180° and 10 lever cam lock mechanism (except for sink and corner unit) Hinge: SS Hinge .Screw: SS 304.Shutter : should be of twin-type construction with sound dampening effect using profill. Shutter cover should be equipped with Bump on for sound dampening. Base Moulding should be made of PVC with corner clips. Ball Slide: 500mm Length Shutter should have provision of roller catch. COVER / FILLER PANELS All side cover panels and back panels, filler panels should be made from CRCA MS panels of 1.0mm thickness with pure epoxy powder coating . SERVICE FITTINGS AND ACCESSORIES Service fittings should be laboratory grade, and water faucets and valve bodies should be cast red brass alloy or bronze forgings, all fittings should be powder plated unless specified otherwise. Service Indexes: Fittings should be identified with service indexes in the color coding as per DIN 12920. PP Sink,Polypropylene Molded Sinks: Made up of 5 mm thick high density and elastic poly propylene with good resistance to organic solvents. Sink - Bowl size to be a minimum of (L x W x D) 560 x 355 x 300 mm. -1 Nos Faucet - 3-way type faucet as per approved make 1 Nos ELECTRICAL ACCESSORIES (6/16 A SWITCHES & SOCKETS) : These are made of High gloss virgin grade engineering thermoplastics to impart a defect free surface. they impart excellent electrical insulation properties i.e. do not melt on heating or catches fire. Owing to this all electrical switches and sockets are capable of handling higher currents and operating temperatures. Front plates can be changed at any time with ease without disturbing the wiring to quickly and economically match changes in the surroundings.WORKTOP : Jet Black Granite: It should be 19mm (+/- 2mm) thick Jet Black Granite worktop. The exposed edges of the worktop should be chamfered and smoothened. The bottom of the worktop should be polished and there should be a V-groove throughout the length of the exposed edges to protect the cabinets from coming in contact with the spillages. The overhang on the storage cabinet is 25 mm at the front side and 30 mm at the sides. The backing material used is a neoprene mat of 6 mm thickness. as directed by Engineer In-charge(As per specified in Technical specification of furniture Page No.30 of NIT) |
| 84 | Providing supply installation of WALL TABLE - 1 WITH SINK 8035mmL X 920mmD X 900mmH WITH ELECTRICAL TRUNKING Construction : Floor based Welded cabinet system having storage body should be flush face construction with intersection of vertical and horizontal members like LH and RH side panel along with front horizontal channel, back panel and bottom panel. It should be relocated anywhere easily as it is an independent unit. Cabinet should of square non-sharp edge construction. Doors should be assembled with SS-304 hinge assembly. Removable back panel should be provided to easily access the service lines running behind the cabinet benches. Intermediate horizontal channels should be provided between door and drawer. Toe-space of 90mm X 90mm is provided at front-bottom side of cabinet. Levelers are provided for easy leveling of welded cabinet. Shelf should be eight-bend panel with 20mm height. Drawer tray should be of single piece construction. Drawer should be well supported on LH and RH ball slide suspension system. Steel door and drawer front should be of double wall construction with sound dampening material filled inside. Doors should be easily removable and hinges should be easily replaceable. Knee space panel should be in 22 gauge construction. Cabinets are tested as per SEFA 8M standard from a SEFA approved Lab and also tested as per EN 14727 from a third party testing agencyDimensions: W=600 mm, 750 mm , D = 530mm, H = 875 mm Configurations: continuous storage MOC: MSCRCA: IS – 513 (1994) Thickness: LH/RH side panels, shutter front, Bottom panel, Top front, Drawer separator, shelf, Alignment channel is of 1.2mm thk. Removable Back panel, Shutter cover, Fr. Rack strip, Top cover panel is of 0.8mmthk Finish: The complete M.S. material of cabinet should be pre-treated (degreased, Zinc phosphated) and epoxy powder coated for better corrosion resistance. The thickness of powder coat should be 45-50 microns, which passes the test of Salt Spray for 1000 hours. It should have a high temperature withstanding capacity with excellent electrical insulation properties.The rear portion of above accessories which is in contact with live metal should be made from thermo set material which will not melt on heating.Handle: Anodized Aluminum Recessed-Type, CTC: 160.0mm Lock: Units have a locking facility with 180° and 10 lever cam lock mechanism (except for sink and corner unit) Hinge: SS Hinge .Screw: SS 304.Shutter : should be of twin-type construction with sound dampening effect using profill. Shutter cover should be equipped with Bump on for sound dampening. Base Moulding should be made of PVC with corner clips. Ball Slide: 500mm Length Shutter should have provision of roller catch. COVER / FILLER PANELS All side cover panels and back panels, filler panels should be made from CRCA MS panels of 1.0mm thickness with pure epoxy powder coating . SERVICE FITTINGS AND ACCESSORIES Service fittings should be laboratory grade, and water faucets and valve bodies should be cast red brass alloy or bronze forgings, all fittings should be powder plated unless specified otherwise. Service Indexes: Fittings should be identified with service indexes in the color coding as per DIN 12920. PP Sink,Polypropylene Molded Sinks: Made up of 5 mm thick high density and elastic poly propylene with good resistance to organic solvents. Sink - Bowl size to be a minimum of (L x W x D) 560 x 355 x 300 mm. -1 Nos Faucet - 3-way type faucet as per approved make 1 Nos ELECTRICAL ACCESSORIES (6/16 A SWITCHES & SOCKETS) : These are made of High gloss virgin grade engineering thermoplastics to impart a defect free surface. they impart excellent electrical insulation properties i.e. do not melt on heating or catches fire. Owing to this all electrical switches and sockets are capable of handling higher currents and operating temperatures. Front plates can be changed at any time with ease without disturbing the wiring to quickly and economically match changes in the surroundings.WORKTOP : Jet Black Granite: It should be 19mm (+/- 2mm) thick Jet Black Granite worktop. The exposed edges of the worktop should be chamfered and smoothened. The bottom of the worktop should be polished and there should be a V-groove throughout the length of the exposed edges to protect the cabinets from coming in contact with the spillages. The overhang on the storage cabinet is 25 mm at the front side and 30 mm at the sides. The backing material used is a neoprene mat of 6 mm thickness. as directed by Engineer In-charge(As per specified in Technical specification of furniture Page No.30 of NIT) |
| 85 | Providing supply installation of WALL TABLE - 1 WITH SINK & PEGBOARD 5385mmL X 770mmD X 900mmH WITH ELECTRICAL TRUNKINGConstruction : Floor based Welded cabinet system having storage body should be flush face construction with intersection of vertical and horizontal members like LH and RH side panel along with front horizontal channel, back panel and bottom panel. It should be relocated anywhere easily as it is an independent unit. Cabinet should of square non-sharp edge construction. Doors should be assembled with SS-304 hinge assembly. Removable back panel should be provided to easily access the service lines running behind the cabinet benches. Intermediate horizontal channels should be provided between door and drawer. Toe-space of 90mm X 90mm is provided at front-bottom side of cabinet. Levelers are provided for easy leveling of welded cabinet. Shelf should be eight-bend panel with 20mm height. Drawer tray should be of single piece construction. Drawer should be well supported on LH and RH ball slide suspension system. Steel door and drawer front should be of double wall construction with sound dampening material filled inside. Doors should be easily removable and hinges should be easily replaceable. Knee space panel should be in 22 gauge construction. Cabinets are tested as per SEFA 8M standard from a SEFA approved Lab and also tested as per EN 14727 from a third party testing agencyDimensions: W=600 mm, 750 mm, 900mm , D = 530mm, H = 875 mm Configurations:Continuous storage MOC: MSCRCA: IS – 513 (1994) Thickness: LH/RH side panels, shutter front, Bottom panel, Top front, Drawer separator, shelf, Alignment channel is of 1.2mm thk. Removable Back panel, Shutter cover, Fr. Rack strip, Top cover panel is of 0.8mmthk Finish: The complete M.S. material of cabinet should be pre-treated (degreased, Zinc phosphated) and epoxy powder coated for better corrosion resistance. The thickness of powder coat should be 45-50 microns, which passes the test of Salt Spray for 1000 hours. It should have a high temperature withstanding capacity with excellent electrical insulation properties.The rear portion of above accessories which is in contact with live metal should be made from thermo set material which will not melt on heating.Handle: Anodized Aluminum Recessed-Type, CTC: 160.0mm Lock: Units have a locking facility with 180° and 10 lever cam lock mechanism (except for sink and corner unit) Hinge: SS Hinge .Screw: SS 304.Shutter : should be of twin-type construction with sound dampening effect using profill. Shutter cover should be equipped with Bump on for sound dampening. Base Moulding should be made of PVC with corner clips. Ball Slide: 500mm Length Shutter should have provision of roller catch. COVER / FILLER PANELS All side cover panels and back panels, filler panels should be made from CRCA MS panels of 1.0mm thickness with pure epoxy powder coating . SERVICE FITTINGS AND ACCESSORIES Service fittings should be laboratory grade, and water faucets and valve bodies should be cast red brass alloy or bronze forgings, all fittings should be powder plated unless specified otherwise. Service Indexes: Fittings should be identified with service indexes in the color coding as per DIN 12920. ELECTRICAL ACCESSORIES (6/16 A SWITCHES & SOCKETS) : These are made of High gloss virgin grade engineering thermoplastics to impart a defect free surface. they impart excellent electrical insulation properties i.e. do not melt on heating or catches fire. Owing to this all electrical switches and sockets are capable of handling higher currents and operating temperatures. Front plates can be changed at any time with ease without disturbing the wiring to quickly and economically match changes in the surroundings.WORKTOP : Jet Black Granite: It should be 19mm (+/- 2mm) thick Jet Black Granite worktop. The exposed edges of the worktop should be chamfered and smoothened. The bottom of the worktop should be polished and there should be a V-groove throughout the length of the exposed edges to protect the cabinets from coming in contact with the spillages. The overhang on the storage cabinet is 25 mm at the front side and 30 mm at the sides. The backing material used is a neoprene mat of 6 mm thickness.PEGBOARD: SS Peg Board with 33 pp Pegs & Tray (Size: 600 mm x 600 mm x 15 mm) as directed by Engineer In-charge(As per specified in Technical specification of furniture Page No.30 of NIT) |
| 86 | Providing supply installation of WALL TABLE - 10 6040mmL X 770mmD X 900mmH WITH ELECTRICAL TRUNKING , LPG VALVEConstruction : Floor based Welded cabinet system having storage body should be flush face construction with intersection of vertical and horizontal members like LH and RH side panel along with front horizontal channel, back panel and bottom panel. It should be relocated anywhere easily as it is an independent unit. Cabinet should of square non-sharp edge construction. Doors should be assembled with SS-304 hinge assembly. Removable back panel should be provided to easily access the service lines running behind the cabinet benches. Intermediate horizontal channels should be provided between door and drawer. Toe-space of 90mm X 90mm is provided at front-bottom side of cabinet. Levelers are provided for easy leveling of welded cabinet. Shelf should be eight-bend panel with 20mm height. Drawer tray should be of single piece construction. Drawer should be well supported on LH and RH ball slide suspension system. Steel door and drawer front should be of double wall construction with sound dampening material filled inside. Doors should be easily removable and hinges should be easily replaceable. Knee space panel should be in 22 gauge construction. Cabinets are tested as per SEFA 8M standard from a SEFA approved Lab and also tested as per EN 14727 from a third party testing agencyDimensions: W=600 mm, 750 mm, 900mm , D = 530mm, H = 875 mm Configurations: continuous storages MOC: MSCRCA: IS – 513 (1994) Thickness: LH/RH side panels, shutter front, Bottom panel, Top front, Drawer separator, shelf, Alignment channel is of 1.2mm thk. Removable Back panel, Shutter cover, Fr. Rack strip, Top cover panel is of 0.8mmthk Finish: The complete M.S. material of cabinet should be pre-treated (degreased, Zinc phosphated) and epoxy powder coated for better corrosion resistance. The thickness of powder coat should be 45-50 microns, which passes the test of Salt Spray for 1000 hours. It should have a high temperature withstanding capacity with excellent electrical insulation properties.The rear portion of above accessories which is in contact with live metal should be made from thermo set material which will not melt on heating.Handle: Anodized Aluminum Recessed-Type, CTC: 160.0mm Lock: Units have a locking facility with 180° and 10 lever cam lock mechanism (except for sink and corner unit) Hinge: SS Hinge .Screw: SS 304.Shutter : should be of twin-type construction with sound dampening effect using profill. Shutter cover should be equipped with Bump on for sound dampening. Base Moulding should be made of PVC with corner clips. Ball Slide: 500mm Length Shutter should have provision of roller catch. COVER / FILLER PANELS All side cover panels and back panels, filler panels should be made from CRCA MS panels of 1.0mm thickness with pure epoxy powder coating . SERVICE FITTINGS AND ACCESSORIES Service fittings should be laboratory grade, and water faucets and valve bodies should be cast red brass alloy or bronze forgings, all fittings should be powder plated unless specified otherwise. Service Indexes: Fittings should be identified with service indexes in the color coding as per DIN 12920. ELECTRICAL ACCESSORIES (6/16 A SWITCHES & SOCKETS) : These are made of High gloss virgin grade engineering thermoplastics to impart a defect free surface. they impart excellent electrical insulation properties i.e. do not melt on heating or catches fire. Owing to this all electrical switches and sockets are capable of handling higher currents and operating temperatures. Front plates can be changed at any time with ease without disturbing the wiring to quickly and economically match changes in the surroundings.WORKTOP : Jet Black Granite: It should be 19mm (+/- 2mm) thick Jet Black Granite worktop. The exposed edges of the worktop should be chamfered and smoothened. The bottom of the worktop should be polished and there should be a V-groove throughout the length of the exposed edges to protect the cabinets from coming in contact with the spillages. The overhang on the storage cabinet is 25 mm at the front side and 30 mm at the sides. The backing material used is a neoprene mat of 6 mm thickness. as directed by Engineer In-charge(As per specified in Technical specification of furniture Page No.30 of NIT) |
| 87 | Providing supply installation of WALL TABLE - 13 16116mmL X 770mmD X 900mmH WITH ELECTRICAL TRUNKINGConstruction : Floor based Welded cabinet system having storage body should be flush face construction with intersection of vertical and horizontal members like LH and RH side panel along with front horizontal channel, back panel and bottom panel. It should be relocated anywhere easily as it is an independent unit. Cabinet should of square non-sharp edge construction. Doors should be assembled with SS-304 hinge assembly. Removable back panel should be provided to easily access the service lines running behind the cabinet benches. Intermediate horizontal channels should be provided between door and drawer. Toe-space of 90mm X 90mm is provided at front-bottom side of cabinet. Levelers are provided for easy leveling of welded cabinet. Shelf should be eight-bend panel with 20mm height. Drawer tray should be of single piece construction. Drawer should be well supported on LH and RH ball slide suspension system. Steel door and drawer front should be of double wall construction with sound dampening material filled inside. Doors should be easily removable and hinges should be easily replaceable. Knee space panel should be in 22 gauge construction. Cabinets are tested as per SEFA 8M standard from a SEFA approved Lab and also tested as per EN 14727 from a third party testing agencyDimensions: W=600 mm, 750 mm, 900mm , D = 530mm, H = 875 mm Configurations: continuous storages MOC: MSCRCA: IS – 513 (1994) Thickness: LH/RH side panels, shutter front, Bottom panel, Top front, Drawer separator, shelf, Alignment channel is of 1.2mm thk. Removable Back panel, Shutter cover, Fr. Rack strip, Top cover panel is of 0.8mmthk Finish: The complete M.S. material of cabinet should be pre-treated (degreased, Zinc phosphated) and epoxy powder coated for better corrosion resistance. The thickness of powder coat should be 45-50 microns, which passes the test of Salt Spray for 1000 hours. It should have a high temperature withstanding capacity with excellent electrical insulation properties.The rear portion of above accessories which is in contact with live metal should be made from thermo set material which will not melt on heating.Handle: Anodized Aluminum Recessed-Type, CTC: 160.0mm Lock: Units have a locking facility with 180° and 10 lever cam lock mechanism (except for sink and corner unit) Hinge: SS Hinge .Screw: SS 304.Shutter : should be of twin-type construction with sound dampening effect using profill. Shutter cover should be equipped with Bump on for sound dampening. Base Moulding should be made of PVC with corner clips. Ball Slide: 500mm Length Shutter should have provision of roller catch. COVER / FILLER PANELS All side cover panels and back panels, filler panels should be made from CRCA MS panels of 1.0mm thickness with pure epoxy powder coating . SERVICE FITTINGS AND ACCESSORIES Service fittings should be laboratory grade, and water faucets and valve bodies should be cast red brass alloy or bronze forgings, all fittings should be powder plated unless specified otherwise. Service Indexes: Fittings should be identified with service indexes in the color coding as per DIN 12920. ELECTRICAL ACCESSORIES (6/16 A SWITCHES & SOCKETS) : These are made of High gloss virgin grade engineering thermoplastics to impart a defect free surface. they impart excellent electrical insulation properties i.e. do not melt on heating or catches fire. Owing to this all electrical switches and sockets are capable of handling higher currents and operating temperatures. Front plates can be changed at any time with ease without disturbing the wiring to quickly and economically match changes in the surroundings.WORKTOP : Jet Black Granite: It should be 19mm (+/- 2mm) thick Jet Black Granite worktop. The exposed edges of the worktop should be chamfered and smoothened. The bottom of the worktop should be polished and there should be a V-groove throughout the length of the exposed edges to protect the cabinets from coming in contact with the spillages. The overhang on the storage cabinet is 25 mm at the front side and 30 mm at the sides. The backing material used is a neoprene mat of 6 mm thickness. as directed by Engineer In-charge(As per specified in Technical specification of furniture Page No.30 of NIT) |
| 88 | Providing supply installation of WALL TABLE - 14 6040mmL X 770mmD X 900mmH WITH ELECTRICAL TRUNKINGConstruction : Floor based Welded cabinet system having storage body should be flush face construction with intersection of vertical and horizontal members like LH and RH side panel along with front horizontal channel, back panel and bottom panel. It should be relocated anywhere easily as it is an independent unit. Cabinet should of square non-sharp edge construction. Doors should be assembled with SS-304 hinge assembly. Removable back panel should be provided to easily access the service lines running behind the cabinet benches. Intermediate horizontal channels should be provided between door and drawer. Toe-space of 90mm X 90mm is provided at front-bottom side of cabinet. Levelers are provided for easy leveling of welded cabinet. Shelf should be eight-bend panel with 20mm height. Drawer tray should be of single piece construction. Drawer should be well supported on LH and RH ball slide suspension system. Steel door and drawer front should be of double wall construction with sound dampening material filled inside. Doors should be easily removable and hinges should be easily replaceable. Knee space panel should be in 22 gauge construction. Cabinets are tested as per SEFA 8M standard from a SEFA approved Lab and also tested as per EN 14727 from a third party testing agencyDimensions: W=600 mm, 750 mm, 900mm , D = 530mm, H = 875 mm Configurations: continuous storages MOC: MSCRCA: IS – 513 (1994) Thickness: LH/RH side panels, shutter front, Bottom panel, Top front, Drawer separator, shelf, Alignment channel is of 1.2mm thk. Removable Back panel, Shutter cover, Fr. Rack strip, Top cover panel is of 0.8mmthk Finish: The complete M.S. material of cabinet should be pre-treated (degreased, Zinc phosphated) and epoxy powder coated for better corrosion resistance. The thickness of powder coat should be 45-50 microns, which passes the test of Salt Spray for 1000 hours. It should have a high temperature withstanding capacity with excellent electrical insulation properties.The rear portion of above accessories which is in contact with live metal should be made from thermo set material which will not melt on heating.Handle: Anodized Aluminum Recessed-Type, CTC: 160.0mm Lock: Units have a locking facility with 180° and 10 lever cam lock mechanism (except for sink and corner unit) Hinge: SS Hinge .Screw: SS 304.Shutter : should be of twin-type construction with sound dampening effect using profill. Shutter cover should be equipped with Bump on for sound dampening. Base Moulding should be made of PVC with corner clips. Ball Slide: 500mm Length Shutter should have provision of roller catch. COVER / FILLER PANELS All side cover panels and back panels, filler panels should be made from CRCA MS panels of 1.0mm thickness with pure epoxy powder coating . SERVICE FITTINGS AND ACCESSORIES Service fittings should be laboratory grade, and water faucets and valve bodies should be cast red brass alloy or bronze forgings, all fittings should be powder plated unless specified otherwise. Service Indexes: Fittings should be identified with service indexes in the color coding as per DIN 12920. ELECTRICAL ACCESSORIES (6/16 A SWITCHES & SOCKETS) : These are made of High gloss virgin grade engineering thermoplastics to impart a defect free surface. they impart excellent electrical insulation properties i.e. do not melt on heating or catches fire. Owing to this all electrical switches and sockets are capable of handling higher currents and operating temperatures. Front plates can be changed at any time with ease without disturbing the wiring to quickly and economically match changes in the surroundings.WORKTOP : Jet Black Granite: It should be 19mm (+/- 2mm) thick Jet Black Granite worktop. The exposed edges of the worktop should be chamfered and smoothened. The bottom of the worktop should be polished and there should be a V-groove throughout the length of the exposed edges to protect the cabinets from coming in contact with the spillages. The overhang on the storage cabinet is 25 mm at the front side and 30 mm at the sides. The backing material used is a neoprene mat of 6 mm thickness. as directed by Engineer In-charge(As per specified in Technical specification of furniture Page No.30 of NIT) |
| 89 | Providing supply installation of WALL TABLE - 17 2740mmL X 920mmD X 900mmH WITH ELECTRICAL TRUNKINGConstruction : Floor based Welded cabinet system having storage body should be flush face construction with intersection of vertical and horizontal members like LH and RH side panel along with front horizontal channel, back panel and bottom panel. It should be relocated anywhere easily as it is an independent unit. Cabinet should of square non-sharp edge construction. Doors should be assembled with SS-304 hinge assembly. Removable back panel should be provided to easily access the service lines running behind the cabinet benches. Intermediate horizontal channels should be provided between door and drawer. Toe-space of 90mm X 90mm is provided at front-bottom side of cabinet. Levelers are provided for easy leveling of welded cabinet. Shelf should be eight-bend panel with 20mm height. Drawer tray should be of single piece construction. Drawer should be well supported on LH and RH ball slide suspension system. Steel door and drawer front should be of double wall construction with sound dampening material filled inside. Doors should be easily removable and hinges should be easily replaceable. Knee space panel should be in 22 gauge construction. Cabinets are tested as per SEFA 8M standard from a SEFA approved Lab and also tested as per EN 14727 from a third party testing agencyDimensions: W=600 mm, 750 mm, 900mm , D = 530mm, H = 875 mm Configurations: continuous storages MOC: MSCRCA: IS – 513 (1994) Thickness: LH/RH side panels, shutter front, Bottom panel, Top front, Drawer separator, shelf, Alignment channel is of 1.2mm thk. Removable Back panel, Shutter cover, Fr. Rack strip, Top cover panel is of 0.8mmthk Finish: The complete M.S. material of cabinet should be pre-treated (degreased, Zinc phosphated) and epoxy powder coated for better corrosion resistance. The thickness of powder coat should be 45-50 microns, which passes the test of Salt Spray for 1000 hours. It should have a high temperature withstanding capacity with excellent electrical insulation properties.The rear portion of above accessories which is in contact with live metal should be made from thermo set material which will not melt on heating.Handle: Anodized Aluminum Recessed-Type, CTC: 160.0mm Lock: Units have a locking facility with 180° and 10 lever cam lock mechanism (except for sink and corner unit) Hinge: SS Hinge .Screw: SS 304.Shutter : should be of twin-type construction with sound dampening effect using profill. Shutter cover should be equipped with Bump on for sound dampening. Base Moulding should be made of PVC with corner clips. Ball Slide: 500mm Length Shutter should have provision of roller catch. COVER / FILLER PANELS All side cover panels and back panels, filler panels should be made from CRCA MS panels of 1.0mm thickness with pure epoxy powder coating . SERVICE FITTINGS AND ACCESSORIES Service fittings should be laboratory grade, and water faucets and valve bodies should be cast red brass alloy or bronze forgings, all fittings should be powder plated unless specified otherwise. Service Indexes: Fittings should be identified with service indexes in the color coding as per DIN 12920. ELECTRICAL ACCESSORIES (6/16 A SWITCHES & SOCKETS) : These are made of High gloss virgin grade engineering thermoplastics to impart a defect free surface. they impart excellent electrical insulation properties i.e. do not melt on heating or catches fire. Owing to this all electrical switches and sockets are capable of handling higher currents and operating temperatures. Front plates can be changed at any time with ease without disturbing the wiring to quickly and economically match changes in the surroundings.WORKTOP : Jet Black Granite: It should be 19mm (+/- 2mm) thick Jet Black Granite worktop. The exposed edges of the worktop should be chamfered and smoothened. The bottom of the worktop should be polished and there should be a V-groove throughout the length of the exposed edges to protect the cabinets from coming in contact with the spillages. The overhang on the storage cabinet is 25 mm at the front side and 30 mm at the sides. The backing material used is a neoprene mat of 6 mm thickness. as directed by Engineer In-charge(As per specified in Technical specification of furniture Page No.30 of NIT) |
| 90 | Providing supply installation of WALL TABLE - 3 2740mmL X 770mmD X 900mmH WITH ELECTRICAL TRUNKINGConstruction : Floor based Welded cabinet system having storage body should be flush face construction with intersection of vertical and horizontal members like LH and RH side panel along with front horizontal channel, back panel and bottom panel. It should be relocated anywhere easily as it is an independent unit. Cabinet should of square non-sharp edge construction. Doors should be assembled with SS-304 hinge assembly. Removable back panel should be provided to easily access the service lines running behind the cabinet benches. Intermediate horizontal channels should be provided between door and drawer. Toe-space of 90mm X 90mm is provided at front-bottom side of cabinet. Levelers are provided for easy leveling of welded cabinet. Shelf should be eight-bend panel with 20mm height. Drawer tray should be of single piece construction. Drawer should be well supported on LH and RH ball slide suspension system. Steel door and drawer front should be of double wall construction with sound dampening material filled inside. Doors should be easily removable and hinges should be easily replaceable. Knee space panel should be in 22 gauge construction. Cabinets are tested as per SEFA 8M standard from a SEFA approved Lab and also tested as per EN 14727 from a third party testing agencyDimensions: W=600 mm, 750 mm, 900mm , D = 530mm, H = 875 mm Configurations: continuous storages MOC: MSCRCA: IS – 513 (1994) Thickness: LH/RH side panels, shutter front, Bottom panel, Top front, Drawer separator, shelf, Alignment channel is of 1.2mm thk. Removable Back panel, Shutter cover, Fr. Rack strip, Top cover panel is of 0.8mmthk Finish: The complete M.S. material of cabinet should be pre-treated (degreased, Zinc phosphated) and epoxy powder coated for better corrosion resistance. The thickness of powder coat should be 45-50 microns, which passes the test of Salt Spray for 1000 hours. It should have a high temperature withstanding capacity with excellent electrical insulation properties.The rear portion of above accessories which is in contact with live metal should be made from thermo set material which will not melt on heating.Handle: Anodized Aluminum Recessed-Type, CTC: 160.0mm Lock: Units have a locking facility with 180° and 10 lever cam lock mechanism (except for sink and corner unit) Hinge: SS Hinge .Screw: SS 304.Shutter : should be of twin-type construction with sound dampening effect using profill. Shutter cover should be equipped with Bump on for sound dampening. Base Moulding should be made of PVC with corner clips. Ball Slide: 500mm Length Shutter should have provision of roller catch. COVER / FILLER PANELS All side cover panels and back panels, filler panels should be made from CRCA MS panels of 1.0mm thickness with pure epoxy powder coating . SERVICE FITTINGS AND ACCESSORIES Service fittings should be laboratory grade, and water faucets and valve bodies should be cast red brass alloy or bronze forgings, all fittings should be powder plated unless specified otherwise. Service Indexes: Fittings should be identified with service indexes in the color coding as per DIN 12920. ELECTRICAL ACCESSORIES (6/16 A SWITCHES & SOCKETS) : These are made of High gloss virgin grade engineering thermoplastics to impart a defect free surface. they impart excellent electrical insulation properties i.e. do not melt on heating or catches fire. Owing to this all electrical switches and sockets are capable of handling higher currents and operating temperatures. Front plates can be changed at any time with ease without disturbing the wiring to quickly and economically match changes in the surroundings.WORKTOP : Jet Black Granite: It should be 19mm (+/- 2mm) thick Jet Black Granite worktop. The exposed edges of the worktop should be chamfered and smoothened. The bottom of the worktop should be polished and there should be a V-groove throughout the length of the exposed edges to protect the cabinets from coming in contact with the spillages. The overhang on the storage cabinet is 25 mm at the front side and 30 mm at the sides. The backing material used is a neoprene mat of 6 mm thickness. as directed by Engineer In-charge(As per specified in Technical specification of furniture Page No.30 of NIT) |
| 91 | Providing supply installation of WALL TABLE - 3 2885mmL X 920mmD X 900mmH WITH ELECTRICAL TRUNKING Construction : Floor based Welded cabinet system having storage body should be flush face construction with intersection of vertical and horizontal members like LH and RH side panel along with front horizontal channel, back panel and bottom panel. It should be relocated anywhere easily as it is an independent unit. Cabinet should of square non-sharp edge construction. Doors should be assembled with SS-304 hinge assembly. Removable back panel should be provided to easily access the service lines running behind the cabinet benches. Intermediate horizontal channels should be provided between door and drawer. Toe-space of 90mm X 90mm is provided at front-bottom side of cabinet. Levelers are provided for easy leveling of welded cabinet. Shelf should be eight-bend panel with 20mm height. Drawer tray should be of single piece construction. Drawer should be well supported on LH and RH ball slide suspension system. Steel door and drawer front should be of double wall construction with sound dampening material filled inside. Doors should be easily removable and hinges should be easily replaceable. Knee space panel should be in 22 gauge construction. Cabinets are tested as per SEFA 8M standard from a SEFA approved Lab and also tested as per EN 14727 from a third party testing agencyDimensions: W=600 mm, 750 mm, 900mm , D = 530mm, H = 875 mm Configurations: continuous storage , MOC: MSCRCA: IS – 513 (1994) Thickness: LH/RH side panels, shutter front, Bottom panel, Top front, Drawer separator, shelf, Alignment channel is of 1.2mm thk. Removable Back panel, Shutter cover, Fr. Rack strip, Top cover panel is of 0.8mmthk Finish: The complete M.S. material of cabinet should be pre-treated (degreased, Zinc phosphated) and epoxy powder coated for better corrosion resistance. The thickness of powder coat should be 45-50 microns, which passes the test of Salt Spray for 1000 hours. It should have a high temperature withstanding capacity with excellent electrical insulation properties.The rear portion of above accessories which is in contact with live metal should be made from thermo set material which will not melt on heating.Handle: Anodized Aluminum Recessed-Type, CTC: 160.0mm Lock: Units have a locking facility with 180° and 10 lever cam lock mechanism (except for sink and corner unit) Hinge: SS Hinge .Screw: SS 304.Shutter : should be of twin-type construction with sound dampening effect using profill. Shutter cover should be equipped with Bump on for sound dampening. Base Moulding should be made of PVC with corner clips. Ball Slide: 500mm Length Shutter should have provision of roller catch. COVER / FILLER PANELS All side cover panels and back panels, filler panels should be made from CRCA MS panels of 1.0mm thickness with pure epoxy powder coating . SERVICE FITTINGS AND ACCESSORIES Service fittings should be laboratory grade, and water faucets and valve bodies should be cast red brass alloy or bronze forgings, all fittings should be powder plated unless specified otherwise. Service Indexes: Fittings should be identified with service indexes in the color coding as per DIN 12920. ELECTRICAL ACCESSORIES (6/16 A SWITCHES & SOCKETS) : These are made of High gloss virgin grade engineering thermoplastics to impart a defect free surface. they impart excellent electrical insulation properties i.e. do not melt on heating or catches fire. Owing to this all electrical switches and sockets are capable of handling higher currents and operating temperatures. Front plates can be changed at any time with ease without disturbing the wiring to quickly and economically match changes in the surroundings.WORKTOP : Jet Black Granite: It should be 19mm (+/- 2mm) thick Jet Black Granite worktop. The exposed edges of the worktop should be chamfered and smoothened. The bottom of the worktop should be polished and there should be a V-groove throughout the length of the exposed edges to protect the cabinets from coming in contact with the spillages. The overhang on the storage cabinet is 25 mm at the front side and 30 mm at the sides. The backing material used is a neoprene mat of 6 mm thickness. as directed by Engineer In-charge(As per specified in Technical specification of furniture Page No.30 of NIT) |
| 92 | Providing supply installation of WALL TABLE - 3 3040mmL X 770mmD X 900mmH WITH ELECTRICAL TRUNKING , LPG VALVEConstruction : Floor based Welded cabinet system having storage body should be flush face construction with intersection of vertical and horizontal members like LH and RH side panel along with front horizontal channel, back panel and bottom panel. It should be relocated anywhere easily as it is an independent unit. Cabinet should of square non-sharp edge construction. Doors should be assembled with SS-304 hinge assembly. Removable back panel should be provided to easily access the service lines running behind the cabinet benches. Intermediate horizontal channels should be provided between door and drawer. Toe-space of 90mm X 90mm is provided at front-bottom side of cabinet. Levelers are provided for easy leveling of welded cabinet. Shelf should be eight-bend panel with 20mm height. Drawer tray should be of single piece construction. Drawer should be well supported on LH and RH ball slide suspension system. Steel door and drawer front should be of double wall construction with sound dampening material filled inside. Doors should be easily removable and hinges should be easily replaceable. Knee space panel should be in 22 gauge construction. Cabinets are tested as per SEFA 8M standard from a SEFA approved Lab and also tested as per EN 14727 from a third party testing agencyDimensions: W=600 mm, 750 mm, 900mm , D = 530mm, H = 875 mm Configurations: continuous storages MOC: MSCRCA: IS – 513 (1994) Thickness: LH/RH side panels, shutter front, Bottom panel, Top front, Drawer separator, shelf, Alignment channel is of 1.2mm thk. Removable Back panel, Shutter cover, Fr. Rack strip, Top cover panel is of 0.8mmthk Finish: The complete M.S. material of cabinet should be pre-treated (degreased, Zinc phosphated) and epoxy powder coated for better corrosion resistance. The thickness of powder coat should be 45-50 microns, which passes the test of Salt Spray for 1000 hours. It should have a high temperature withstanding capacity with excellent electrical insulation properties.The rear portion of above accessories which is in contact with live metal should be made from thermo set material which will not melt on heating.Handle: Anodized Aluminum Recessed-Type, CTC: 160.0mm Lock: Units have a locking facility with 180° and 10 lever cam lock mechanism (except for sink and corner unit) Hinge: SS Hinge .Screw: SS 304.Shutter : should be of twin-type construction with sound dampening effect using profill. Shutter cover should be equipped with Bump on for sound dampening. Base Moulding should be made of PVC with corner clips. Ball Slide: 500mm Length Shutter should have provision of roller catch. COVER / FILLER PANELS All side cover panels and back panels, filler panels should be made from CRCA MS panels of 1.0mm thickness with pure epoxy powder coating . SERVICE FITTINGS AND ACCESSORIES Service fittings should be laboratory grade, and water faucets and valve bodies should be cast red brass alloy or bronze forgings, all fittings should be powder plated unless specified otherwise. Service Indexes: Fittings should be identified with service indexes in the color coding as per DIN 12920. ELECTRICAL ACCESSORIES (6/16 A SWITCHES & SOCKETS) : These are made of High gloss virgin grade engineering thermoplastics to impart a defect free surface. they impart excellent electrical insulation properties i.e. do not melt on heating or catches fire. Owing to this all electrical switches and sockets are capable of handling higher currents and operating temperatures. Front plates can be changed at any time with ease without disturbing the wiring to quickly and economically match changes in the surroundings.WORKTOP : Jet Black Granite: It should be 19mm (+/- 2mm) thick Jet Black Granite worktop. The exposed edges of the worktop should be chamfered and smoothened. The bottom of the worktop should be polished and there should be a V-groove throughout the length of the exposed edges to protect the cabinets from coming in contact with the spillages. The overhang on the storage cabinet is 25 mm at the front side and 30 mm at the sides. The backing material used is a neoprene mat of 6 mm thickness. as directed by Engineer In-charge(As per specified in Technical specification of furniture Page No.30 of NIT) |
| 93 | Providing supply installation of WALL TABLE - 3 3040mmL X 770mmD X 900mmH WITH ELECTRICAL TRUNKINGConstruction : Floor based Welded cabinet system having storage body should be flush face construction with intersection of vertical and horizontal members like LH and RH side panel along with front horizontal channel, back panel and bottom panel. It should be relocated anywhere easily as it is an independent unit. Cabinet should of square non-sharp edge construction. Doors should be assembled with SS-304 hinge assembly. Removable back panel should be provided to easily access the service lines running behind the cabinet benches. Intermediate horizontal channels should be provided between door and drawer. Toe-space of 90mm X 90mm is provided at front-bottom side of cabinet. Levelers are provided for easy leveling of welded cabinet. Shelf should be eight-bend panel with 20mm height. Drawer tray should be of single piece construction. Drawer should be well supported on LH and RH ball slide suspension system. Steel door and drawer front should be of double wall construction with sound dampening material filled inside. Doors should be easily removable and hinges should be easily replaceable. Knee space panel should be in 22 gauge construction. Cabinets are tested as per SEFA 8M standard from a SEFA approved Lab and also tested as per EN 14727 from a third party testing agencyDimensions: W=600 mm, 750 mm, 900mm , D = 530mm, H = 875 mm Configurations: continuous storages MOC: MSCRCA: IS – 513 (1994) Thickness: LH/RH side panels, shutter front, Bottom panel, Top front, Drawer separator, shelf, Alignment channel is of 1.2mm thk. Removable Back panel, Shutter cover, Fr. Rack strip, Top cover panel is of 0.8mmthk Finish: The complete M.S. material of cabinet should be pre-treated (degreased, Zinc phosphated) and epoxy powder coated for better corrosion resistance. The thickness of powder coat should be 45-50 microns, which passes the test of Salt Spray for 1000 hours. It should have a high temperature withstanding capacity with excellent electrical insulation properties.The rear portion of above accessories which is in contact with live metal should be made from thermo set material which will not melt on heating.Handle: Anodized Aluminum Recessed-Type, CTC: 160.0mm Lock: Units have a locking facility with 180° and 10 lever cam lock mechanism (except for sink and corner unit) Hinge: SS Hinge .Screw: SS 304.Shutter : should be of twin-type construction with sound dampening effect using profill. Shutter cover should be equipped with Bump on for sound dampening. Base Moulding should be made of PVC with corner clips. Ball Slide: 500mm Length Shutter should have provision of roller catch. COVER / FILLER PANELS All side cover panels and back panels, filler panels should be made from CRCA MS panels of 1.0mm thickness with pure epoxy powder coating . SERVICE FITTINGS AND ACCESSORIES Service fittings should be laboratory grade, and water faucets and valve bodies should be cast red brass alloy or bronze forgings, all fittings should be powder plated unless specified otherwise. Service Indexes: Fittings should be identified with service indexes in the color coding as per DIN 12920. ELECTRICAL ACCESSORIES (6/16 A SWITCHES & SOCKETS) : These are made of High gloss virgin grade engineering thermoplastics to impart a defect free surface. they impart excellent electrical insulation properties i.e. do not melt on heating or catches fire. Owing to this all electrical switches and sockets are capable of handling higher currents and operating temperatures. Front plates can be changed at any time with ease without disturbing the wiring to quickly and economically match changes in the surroundings.WORKTOP : Jet Black Granite: It should be 19mm (+/- 2mm) thick Jet Black Granite worktop. The exposed edges of the worktop should be chamfered and smoothened. The bottom of the worktop should be polished and there should be a V-groove throughout the length of the exposed edges to protect the cabinets from coming in contact with the spillages. The overhang on the storage cabinet is 25 mm at the front side and 30 mm at the sides. The backing material used is a neoprene mat of 6 mm thickness. as directed by Engineer In-charge(As per specified in Technical specification of furniture Page No.30 of NIT) |
| 94 | Providing supply installation of WALL TABLE - 3 5115mmL X 920mmD X 900mmH WITH ELECTRICAL TRUNKING Construction : Floor based Welded cabinet system having storage body should be flush face construction with intersection of vertical and horizontal members like LH and RH side panel along with front horizontal channel, back panel and bottom panel. It should be relocated anywhere easily as it is an independent unit. Cabinet should of square non-sharp edge construction. Doors should be assembled with SS-304 hinge assembly. Removable back panel should be provided to easily access the service lines running behind the cabinet benches. Intermediate horizontal channels should be provided between door and drawer. Toe-space of 90mm X 90mm is provided at front-bottom side of cabinet. Levelers are provided for easy leveling of welded cabinet. Shelf should be eight-bend panel with 20mm height. Drawer tray should be of single piece construction. Drawer should be well supported on LH and RH ball slide suspension system. Steel door and drawer front should be of double wall construction with sound dampening material filled inside. Doors should be easily removable and hinges should be easily replaceable. Knee space panel should be in 22 gauge construction. Cabinets are tested as per SEFA 8M standard from a SEFA approved Lab and also tested as per EN 14727 from a third party testing agencyDimensions: W=600 mm, 750 mm, 900mm , D = 530mm, H = 875 mm Configurations: continuous storages MOC: MSCRCA: IS – 513 (1994) Thickness: LH/RH side panels, shutter front, Bottom panel, Top front, Drawer separator, shelf, Alignment channel is of 1.2mm thk. Removable Back panel, Shutter cover, Fr. Rack strip, Top cover panel is of 0.8mmthk Finish: The complete M.S. material of cabinet should be pre-treated (degreased, Zinc phosphated) and epoxy powder coated for better corrosion resistance. The thickness of powder coat should be 45-50 microns, which passes the test of Salt Spray for 1000 hours. It should have a high temperature withstanding capacity with excellent electrical insulation properties.The rear portion of above accessories which is in contact with live metal should be made from thermo set material which will not melt on heating.Handle: Anodized Aluminum Recessed-Type, CTC: 160.0mm Lock: Units have a locking facility with 180° and 10 lever cam lock mechanism (except for sink and corner unit) Hinge: SS Hinge .Screw: SS 304.Shutter : should be of twin-type construction with sound dampening effect using profill. Shutter cover should be equipped with Bump on for sound dampening. Base Moulding should be made of PVC with corner clips. Ball Slide: 500mm Length Shutter should have provision of roller catch. COVER / FILLER PANELS All side cover panels and back panels, filler panels should be made from CRCA MS panels of 1.0mm thickness with pure epoxy powder coating . SERVICE FITTINGS AND ACCESSORIES Service fittings should be laboratory grade, and water faucets and valve bodies should be cast red brass alloy or bronze forgings, all fittings should be powder plated unless specified otherwise. Service Indexes: Fittings should be identified with service indexes in the color coding as per DIN 12920. ELECTRICAL ACCESSORIES (6/16 A SWITCHES & SOCKETS) : These are made of High gloss virgin grade engineering thermoplastics to impart a defect free surface. they impart excellent electrical insulation properties i.e. do not melt on heating or catches fire. Owing to this all electrical switches and sockets are capable of handling higher currents and operating temperatures. Front plates can be changed at any time with ease without disturbing the wiring to quickly and economically match changes in the surroundings.WORKTOP : Jet Black Granite: It should be 19mm (+/- 2mm) thick Jet Black Granite worktop. The exposed edges of the worktop should be chamfered and smoothened. The bottom of the worktop should be polished and there should be a V-groove throughout the length of the exposed edges to protect the cabinets from coming in contact with the spillages. The overhang on the storage cabinet is 25 mm at the front side and 30 mm at the sides. The backing material used is a neoprene mat of 6 mm thickness. as directed by Engineer In-charge(As per specified in Technical specification of furniture Page No.30 of NIT) |
| 95 | Providing supply installation of WALL TABLE - 3 5385mmL X 770mmD X 900mmH WITH ELECTRICAL TRUNKINGConstruction : Floor based Welded cabinet system having storage body should be flush face construction with intersection of vertical and horizontal members like LH and RH side panel along with front horizontal channel, back panel and bottom panel. It should be relocated anywhere easily as it is an independent unit. Cabinet should of square non-sharp edge construction. Doors should be assembled with SS-304 hinge assembly. Removable back panel should be provided to easily access the service lines running behind the cabinet benches. Intermediate horizontal channels should be provided between door and drawer. Toe-space of 90mm X 90mm is provided at front-bottom side of cabinet. Levelers are provided for easy leveling of welded cabinet. Shelf should be eight-bend panel with 20mm height. Drawer tray should be of single piece construction. Drawer should be well supported on LH and RH ball slide suspension system. Steel door and drawer front should be of double wall construction with sound dampening material filled inside. Doors should be easily removable and hinges should be easily replaceable. Knee space panel should be in 22 gauge construction. Cabinets are tested as per SEFA 8M standard from a SEFA approved Lab and also tested as per EN 14727 from a third party testing agencyDimensions: W=600 mm, 750 mm, 900mm , D = 530mm, H = 875 mm Configurations:Continuous storage MOC: MSCRCA: IS – 513 (1994) Thickness: LH/RH side panels, shutter front, Bottom panel, Top front, Drawer separator, shelf, Alignment channel is of 1.2mm thk. Removable Back panel, Shutter cover, Fr. Rack strip, Top cover panel is of 0.8mmthk Finish: The complete M.S. material of cabinet should be pre-treated (degreased, Zinc phosphated) and epoxy powder coated for better corrosion resistance. The thickness of powder coat should be 45-50 microns, which passes the test of Salt Spray for 1000 hours. It should have a high temperature withstanding capacity with excellent electrical insulation properties.The rear portion of above accessories which is in contact with live metal should be made from thermo set material which will not melt on heating.Handle: Anodized Aluminum Recessed-Type, CTC: 160.0mm Lock: Units have a locking facility with 180° and 10 lever cam lock mechanism (except for sink and corner unit) Hinge: SS Hinge .Screw: SS 304.Shutter : should be of twin-type construction with sound dampening effect using profill. Shutter cover should be equipped with Bump on for sound dampening. Base Moulding should be made of PVC with corner clips. Ball Slide: 500mm Length Shutter should have provision of roller catch. COVER / FILLER PANELS All side cover panels and back panels, filler panels should be made from CRCA MS panels of 1.0mm thickness with pure epoxy powder coating . SERVICE FITTINGS AND ACCESSORIES Service fittings should be laboratory grade, and water faucets and valve bodies should be cast red brass alloy or bronze forgings, all fittings should be powder plated unless specified otherwise. Service Indexes: Fittings should be identified with service indexes in the color coding as per DIN 12920. ELECTRICAL ACCESSORIES (6/16 A SWITCHES & SOCKETS) : These are made of High gloss virgin grade engineering thermoplastics to impart a defect free surface. they impart excellent electrical insulation properties i.e. do not melt on heating or catches fire. Owing to this all electrical switches and sockets are capable of handling higher currents and operating temperatures. Front plates can be changed at any time with ease without disturbing the wiring to quickly and economically match changes in the surroundings.WORKTOP : Jet Black Granite: It should be 19mm (+/- 2mm) thick Jet Black Granite worktop. The exposed edges of the worktop should be chamfered and smoothened. The bottom of the worktop should be polished and there should be a V-groove throughout the length of the exposed edges to protect the cabinets from coming in contact with the spillages. The overhang on the storage cabinet is 25 mm at the front side and 30 mm at the sides. The backing material used is a neoprene mat of 6 mm thickness. as directed by Engineer In-charge(As per specified in Technical specification of furniture Page No.30 of NIT) |
| 96 | Providing supply installation of WALL TABLE - 3 5415mmL X 770mmD X 900mmH WITH ELECTRICAL TRUNKINGConstruction : Floor based Welded cabinet system having storage body should be flush face construction with intersection of vertical and horizontal members like LH and RH side panel along with front horizontal channel, back panel and bottom panel. It should be relocated anywhere easily as it is an independent unit. Cabinet should of square non-sharp edge construction. Doors should be assembled with SS-304 hinge assembly. Removable back panel should be provided to easily access the service lines running behind the cabinet benches. Intermediate horizontal channels should be provided between door and drawer. Toe-space of 90mm X 90mm is provided at front-bottom side of cabinet. Levelers are provided for easy leveling of welded cabinet. Shelf should be eight-bend panel with 20mm height. Drawer tray should be of single piece construction. Drawer should be well supported on LH and RH ball slide suspension system. Steel door and drawer front should be of double wall construction with sound dampening material filled inside. Doors should be easily removable and hinges should be easily replaceable. Knee space panel should be in 22 gauge construction. Cabinets are tested as per SEFA 8M standard from a SEFA approved Lab and also tested as per EN 14727 from a third party testing agencyDimensions: W=600 mm, 750 mm, 900mm , D = 530mm, H = 875 mm Configurations:Continuous storage MOC: MSCRCA: IS – 513 (1994) Thickness: LH/RH side panels, shutter front, Bottom panel, Top front, Drawer separator, shelf, Alignment channel is of 1.2mm thk. Removable Back panel, Shutter cover, Fr. Rack strip, Top cover panel is of 0.8mmthk Finish: The complete M.S. material of cabinet should be pre-treated (degreased, Zinc phosphated) and epoxy powder coated for better corrosion resistance. The thickness of powder coat should be 45-50 microns, which passes the test of Salt Spray for 1000 hours. It should have a high temperature withstanding capacity with excellent electrical insulation properties.The rear portion of above accessories which is in contact with live metal should be made from thermo set material which will not melt on heating.Handle: Anodized Aluminum Recessed-Type, CTC: 160.0mm Lock: Units have a locking facility with 180° and 10 lever cam lock mechanism (except for sink and corner unit) Hinge: SS Hinge .Screw: SS 304.Shutter : should be of twin-type construction with sound dampening effect using profill. Shutter cover should be equipped with Bump on for sound dampening. Base Moulding should be made of PVC with corner clips. Ball Slide: 500mm Length Shutter should have provision of roller catch. COVER / FILLER PANELS All side cover panels and back panels, filler panels should be made from CRCA MS panels of 1.0mm thickness with pure epoxy powder coating . SERVICE FITTINGS AND ACCESSORIES Service fittings should be laboratory grade, and water faucets and valve bodies should be cast red brass alloy or bronze forgings, all fittings should be powder plated unless specified otherwise. Service Indexes: Fittings should be identified with service indexes in the color coding as per DIN 12920. ELECTRICAL ACCESSORIES (6/16 A SWITCHES & SOCKETS) : These are made of High gloss virgin grade engineering thermoplastics to impart a defect free surface. they impart excellent electrical insulation properties i.e. do not melt on heating or catches fire. Owing to this all electrical switches and sockets are capable of handling higher currents and operating temperatures. Front plates can be changed at any time with ease without disturbing the wiring to quickly and economically match changes in the surroundings.WORKTOP : Jet Black Granite: It should be 19mm (+/- 2mm) thick Jet Black Granite worktop. The exposed edges of the worktop should be chamfered and smoothened. The bottom of the worktop should be polished and there should be a V-groove throughout the length of the exposed edges to protect the cabinets from coming in contact with the spillages. The overhang on the storage cabinet is 25 mm at the front side and 30 mm at the sides. The backing material used is a neoprene mat of 6 mm thickness. as directed by Engineer In-charge(As per specified in Technical specification of furniture Page No.30 of NIT) |
| 97 | Providing supply installation of WALL TABLE - 9 16996mmL X 770mmD X 900mmH WITH ELECTRICAL TRUNKINGConstruction : Floor based Welded cabinet system having storage body should be flush face construction with intersection of vertical and horizontal members like LH and RH side panel along with front horizontal channel, back panel and bottom panel. It should be relocated anywhere easily as it is an independent unit. Cabinet should of square non-sharp edge construction. Doors should be assembled with SS-304 hinge assembly. Removable back panel should be provided to easily access the service lines running behind the cabinet benches. Intermediate horizontal channels should be provided between door and drawer. Toe-space of 90mm X 90mm is provided at front-bottom side of cabinet. Levelers are provided for easy leveling of welded cabinet. Shelf should be eight-bend panel with 20mm height. Drawer tray should be of single piece construction. Drawer should be well supported on LH and RH ball slide suspension system. Steel door and drawer front should be of double wall construction with sound dampening material filled inside. Doors should be easily removable and hinges should be easily replaceable. Knee space panel should be in 22 gauge construction. Cabinets are tested as per SEFA 8M standard from a SEFA approved Lab and also tested as per EN 14727 from a third party testing agencyDimensions: W=600 mm, 750 mm, 900mm , D = 530mm, H = 875 mm Configurations: continuous storages MOC: MSCRCA: IS – 513 (1994) Thickness: LH/RH side panels, shutter front, Bottom panel, Top front, Drawer separator, shelf, Alignment channel is of 1.2mm thk. Removable Back panel, Shutter cover, Fr. Rack strip, Top cover panel is of 0.8mmthk Finish: The complete M.S. material of cabinet should be pre-treated (degreased, Zinc phosphated) and epoxy powder coated for better corrosion resistance. The thickness of powder coat should be 45-50 microns, which passes the test of Salt Spray for 1000 hours. It should have a high temperature withstanding capacity with excellent electrical insulation properties.The rear portion of above accessories which is in contact with live metal should be made from thermo set material which will not melt on heating.Handle: Anodized Aluminum Recessed-Type, CTC: 160.0mm Lock: Units have a locking facility with 180° and 10 lever cam lock mechanism (except for sink and corner unit) Hinge: SS Hinge .Screw: SS 304.Shutter : should be of twin-type construction with sound dampening effect using profill. Shutter cover should be equipped with Bump on for sound dampening. Base Moulding should be made of PVC with corner clips. Ball Slide: 500mm Length Shutter should have provision of roller catch. COVER / FILLER PANELS All side cover panels and back panels, filler panels should be made from CRCA MS panels of 1.0mm thickness with pure epoxy powder coating . SERVICE FITTINGS AND ACCESSORIES Service fittings should be laboratory grade, and water faucets and valve bodies should be cast red brass alloy or bronze forgings, all fittings should be powder plated unless specified otherwise. Service Indexes: Fittings should be identified with service indexes in the color coding as per DIN 12920. ELECTRICAL ACCESSORIES (6/16 A SWITCHES & SOCKETS) : These are made of High gloss virgin grade engineering thermoplastics to impart a defect free surface. they impart excellent electrical insulation properties i.e. do not melt on heating or catches fire. Owing to this all electrical switches and sockets are capable of handling higher currents and operating temperatures. Front plates can be changed at any time with ease without disturbing the wiring to quickly and economically match changes in the surroundings.WORKTOP : Jet Black Granite: It should be 19mm (+/- 2mm) thick Jet Black Granite worktop. The exposed edges of the worktop should be chamfered and smoothened. The bottom of the worktop should be polished and there should be a V-groove throughout the length of the exposed edges to protect the cabinets from coming in contact with the spillages. The overhang on the storage cabinet is 25 mm at the front side and 30 mm at the sides. The backing material used is a neoprene mat of 6 mm thickness. as directed by Engineer In-charge(As per specified in Technical specification of furniture Page No.30 of NIT) |
| 98 | Providing supply installation of WALL TABLE WITH SINK - 1 11235mmL X 920mmD X 900mmH WITH ELECTRICAL TRUNKINGConstruction : Floor based Welded cabinet system having storage body should be flush face construction with intersection of vertical and horizontal members like LH and RH side panel along with front horizontal channel, back panel and bottom panel. It should be relocated anywhere easily as it is an independent unit. Cabinet should of square non-sharp edge construction. Doors should be assembled with SS-304 hinge assembly. Removable back panel should be provided to easily access the service lines running behind the cabinet benches. Intermediate horizontal channels should be provided between door and drawer. Toe-space of 90mm X 90mm is provided at front-bottom side of cabinet. Levelers are provided for easy leveling of welded cabinet. Shelf should be eight-bend panel with 20mm height. Drawer tray should be of single piece construction. Drawer should be well supported on LH and RH ball slide suspension system. Steel door and drawer front should be of double wall construction with sound dampening material filled inside. Doors should be easily removable and hinges should be easily replaceable. Knee space panel should be in 22 gauge construction. Cabinets are tested as per SEFA 8M standard from a SEFA approved Lab and also tested as per EN 14727 from a third party testing agencyDimensions: W=600 mm, 750 mm , D = 530mm, H = 875 mm Configurations: continuous storage MOC: MSCRCA: IS – 513 (1994) Thickness: LH/RH side panels, shutter front, Bottom panel, Top front, Drawer separator, shelf, Alignment channel is of 1.2mm thk. Removable Back panel, Shutter cover, Fr. Rack strip, Top cover panel is of 0.8mmthk Finish: The complete M.S. material of cabinet should be pre-treated (degreased, Zinc phosphated) and epoxy powder coated for better corrosion resistance. The thickness of powder coat should be 45-50 microns, which passes the test of Salt Spray for 1000 hours. It should have a high temperature withstanding capacity with excellent electrical insulation properties.The rear portion of above accessories which is in contact with live metal should be made from thermo set material which will not melt on heating.Handle: Anodized Aluminum Recessed-Type, CTC: 160.0mm Lock: Units have a locking facility with 180° and 10 lever cam lock mechanism (except for sink and corner unit) Hinge: SS Hinge .Screw: SS 304.Shutter : should be of twin-type construction with sound dampening effect using profill. Shutter cover should be equipped with Bump on for sound dampening. Base Moulding should be made of PVC with corner clips. Ball Slide: 500mm Length Shutter should have provision of roller catch. COVER / FILLER PANELS All side cover panels and back panels, filler panels should be made from CRCA MS panels of 1.0mm thickness with pure epoxy powder coating . SERVICE FITTINGS AND ACCESSORIES Service fittings should be laboratory grade, and water faucets and valve bodies should be cast red brass alloy or bronze forgings, all fittings should be powder plated unless specified otherwise. Service Indexes: Fittings should be identified with service indexes in the color coding as per DIN 12920. PP Sink,Polypropylene Molded Sinks: Made up of 5 mm thick high density and elastic poly propylene with good resistance to organic solvents. Sink - Bowl size to be a minimum of (L x W x D) 560 x 355 x 300 mm. -1 Nos Faucet - 3-way type faucet as per approved make 1 Nos ELECTRICAL ACCESSORIES (6/16 A SWITCHES & SOCKETS) : These are made of High gloss virgin grade engineering thermoplastics to impart a defect free surface. they impart excellent electrical insulation properties i.e. do not melt on heating or catches fire. Owing to this all electrical switches and sockets are capable of handling higher currents and operating temperatures. Front plates can be changed at any time with ease without disturbing the wiring to quickly and economically match changes in the surroundings.WORKTOP : Jet Black Granite: It should be 19mm (+/- 2mm) thick Jet Black Granite worktop. The exposed edges of the worktop should be chamfered and smoothened. The bottom of the worktop should be polished and there should be a V-groove throughout the length of the exposed edges to protect the cabinets from coming in contact with the spillages. The overhang on the storage cabinet is 25 mm at the front side and 30 mm at the sides. The backing material used is a neoprene mat of 6 mm thickness. as directed by Engineer In-charge(As per specified in Technical specification of furniture Page No.30 of NIT) |
| 99 | Providing supply installation of WALL TABLE WITH SINK - 1 16116mmL X 770mmD X 900mmH WITH ELECTRICAL TRUNKING , PEGBOARD & LPG VALVEConstruction : Floor based Welded cabinet system having storage body should be flush face construction with intersection of vertical and horizontal members like LH and RH side panel along with front horizontal channel, back panel and bottom panel. It should be relocated anywhere easily as it is an independent unit. Cabinet should of square non-sharp edge construction. Doors should be assembled with SS-304 hinge assembly. Removable back panel should be provided to easily access the service lines running behind the cabinet benches. Intermediate horizontal channels should be provided between door and drawer. Toe-space of 90mm X 90mm is provided at front-bottom side of cabinet. Levelers are provided for easy leveling of welded cabinet. Shelf should be eight-bend panel with 20mm height. Drawer tray should be of single piece construction. Drawer should be well supported on LH and RH ball slide suspension system. Steel door and drawer front should be of double wall construction with sound dampening material filled inside. Doors should be easily removable and hinges should be easily replaceable. Knee space panel should be in 22 gauge construction. Cabinets are tested as per SEFA 8M standard from a SEFA approved Lab and also tested as per EN 14727 from a third party testing agencyDimensions: W=600 mm, 750 mm, 900mm , D = 530mm, H = 875 mm Configurations: continuous storages MOC: MSCRCA: IS – 513 (1994) Thickness: LH/RH side panels, shutter front, Bottom panel, Top front, Drawer separator, shelf, Alignment channel is of 1.2mm thk. Removable Back panel, Shutter cover, Fr. Rack strip, Top cover panel is of 0.8mmthk Finish: The complete M.S. material of cabinet should be pre-treated (degreased, Zinc phosphated) and epoxy powder coated for better corrosion resistance. The thickness of powder coat should be 45-50 microns, which passes the test of Salt Spray for 1000 hours. It should have a high temperature withstanding capacity with excellent electrical insulation properties.The rear portion of above accessories which is in contact with live metal should be made from thermo set material which will not melt on heating.Handle: Anodized Aluminum Recessed-Type, CTC: 160.0mm Lock: Units have a locking facility with 180° and 10 lever cam lock mechanism (except for sink and corner unit) Hinge: SS Hinge .Screw: SS 304.Shutter : should be of twin-type construction with sound dampening effect using profill. Shutter cover should be equipped with Bump on for sound dampening. Base Moulding should be made of PVC with corner clips. Ball Slide: 500mm Length Shutter should have provision of roller catch. COVER / FILLER PANELS All side cover panels and back panels, filler panels should be made from CRCA MS panels of 1.0mm thickness with pure epoxy powder coating . SERVICE FITTINGS AND ACCESSORIES Service fittings should be laboratory grade, and water faucets and valve bodies should be cast red brass alloy or bronze forgings, all fittings should be powder plated unless specified otherwise. Service Indexes: Fittings should be identified with service indexes in the color coding as per DIN 12920. ELECTRICAL ACCESSORIES (6/16 A SWITCHES & SOCKETS) : These are made of High gloss virgin grade engineering thermoplastics to impart a defect free surface. they impart excellent electrical insulation properties i.e. do not melt on heating or catches fire. Owing to this all electrical switches and sockets are capable of handling higher currents and operating temperatures. Front plates can be changed at any time with ease without disturbing the wiring to quickly and economically match changes in the surroundings.PP Sink: ,Polypropylene Molded Sinks: Made up of 5 mm thick high density and elastic poly propylene with good resistance to organic solvents. Sink - Bowl size to be a minimum of (L x W x D) 560 x 355 x 300 mm. Faucet - 3-way type faucet as per approved make PEGBOARD: SS Peg Board with 33 pp Pegs & Tray (Size: 600 mm x 600 mm x 15 mm)WORKTOP : Jet Black Granite: It should be 19mm (+/- 2mm) thick Jet Black Granite worktop. The exposed edges of the worktop should be chamfered and smoothened. The bottom of the worktop should be polished and there should be a V-groove throughout the length of the exposed edges to protect the cabinets from coming in contact with the spillages. The overhang on the storage cabinet is 25 mm at the front side and 30 mm at the sides. The backing material used is a neoprene mat of 6 mm thickness. as directed by Engineer In-charge(As per specified in Technical specification of furniture Page No.30 of NIT) |
| 100 | Providing supply installation of WALL TABLE WITH SINK - 1 16968mmL X 770mmD X 900mmH WITH ELECTRICAL TRUNKING , LPG VALVEConstruction : Floor based Welded cabinet system having storage body should be flush face construction with intersection of vertical and horizontal members like LH and RH side panel along with front horizontal channel, back panel and bottom panel. It should be relocated anywhere easily as it is an independent unit. Cabinet should of square non-sharp edge construction. Doors should be assembled with SS-304 hinge assembly. Removable back panel should be provided to easily access the service lines running behind the cabinet benches. Intermediate horizontal channels should be provided between door and drawer. Toe-space of 90mm X 90mm is provided at front-bottom side of cabinet. Levelers are provided for easy leveling of welded cabinet. Shelf should be eight-bend panel with 20mm height. Drawer tray should be of single piece construction. Drawer should be well supported on LH and RH ball slide suspension system. Steel door and drawer front should be of double wall construction with sound dampening material filled inside. Doors should be easily removable and hinges should be easily replaceable. Knee space panel should be in 22 gauge construction. Cabinets are tested as per SEFA 8M standard from a SEFA approved Lab and also tested as per EN 14727 from a third party testing agencyDimensions: W=600 mm, 750 mm, 900mm , D = 530mm, H = 875 mm Configurations: continuous storages MOC: MSCRCA: IS – 513 (1994) Thickness: LH/RH side panels, shutter front, Bottom panel, Top front, Drawer separator, shelf, Alignment channel is of 1.2mm thk. Removable Back panel, Shutter cover, Fr. Rack strip, Top cover panel is of 0.8mmthk Finish: The complete M.S. material of cabinet should be pre-treated (degreased, Zinc phosphated) and epoxy powder coated for better corrosion resistance. The thickness of powder coat should be 45-50 microns, which passes the test of Salt Spray for 1000 hours. It should have a high temperature withstanding capacity with excellent electrical insulation properties.The rear portion of above accessories which is in contact with live metal should be made from thermo set material which will not melt on heating.Handle: Anodized Aluminum Recessed-Type, CTC: 160.0mm Lock: Units have a locking facility with 180° and 10 lever cam lock mechanism (except for sink and corner unit) Hinge: SS Hinge .Screw: SS 304.Shutter : should be of twin-type construction with sound dampening effect using profill. Shutter cover should be equipped with Bump on for sound dampening. Base Moulding should be made of PVC with corner clips. Ball Slide: 500mm Length Shutter should have provision of roller catch. COVER / FILLER PANELS All side cover panels and back panels, filler panels should be made from CRCA MS panels of 1.0mm thickness with pure epoxy powder coating . SERVICE FITTINGS AND ACCESSORIES Service fittings should be laboratory grade, and water faucets and valve bodies should be cast red brass alloy or bronze forgings, all fittings should be powder plated unless specified otherwise. Service Indexes: Fittings should be identified with service indexes in the color coding as per DIN 12920. ELECTRICAL ACCESSORIES (6/16 A SWITCHES & SOCKETS) : These are made of High gloss virgin grade engineering thermoplastics to impart a defect free surface. they impart excellent electrical insulation properties i.e. do not melt on heating or catches fire. Owing to this all electrical switches and sockets are capable of handling higher currents and operating temperatures. Front plates can be changed at any time with ease without disturbing the wiring to quickly and economically match changes in the surroundings.WORKTOP : Jet Black Granite: It should be 19mm (+/- 2mm) thick Jet Black Granite worktop. The exposed edges of the worktop should be chamfered and smoothened. The bottom of the worktop should be polished and there should be a V-groove throughout the length of the exposed edges to protect the cabinets from coming in contact with the spillages. The overhang on the storage cabinet is 25 mm at the front side and 30 mm at the sides. The backing material used is a neoprene mat of 6 mm thickness. as directed by Engineer In-charge(As per specified in Technical specification of furniture Page No.30 of NIT) |
| 101 | Providing supply installation of WALL TABLE WITH SINK - 1 19871mmL X 920mmD X 900mmH WITH ELECTRICAL TRUNKINGConstruction : Floor based Welded cabinet system having storage body should be flush face construction with intersection of vertical and horizontal members like LH and RH side panel along with front horizontal channel, back panel and bottom panel. It should be relocated anywhere easily as it is an independent unit. Cabinet should of square non-sharp edge construction. Doors should be assembled with SS-304 hinge assembly. Removable back panel should be provided to easily access the service lines running behind the cabinet benches. Intermediate horizontal channels should be provided between door and drawer. Toe-space of 90mm X 90mm is provided at front-bottom side of cabinet. Levelers are provided for easy leveling of welded cabinet. Shelf should be eight-bend panel with 20mm height. Drawer tray should be of single piece construction. Drawer should be well supported on LH and RH ball slide suspension system. Steel door and drawer front should be of double wall construction with sound dampening material filled inside. Doors should be easily removable and hinges should be easily replaceable. Knee space panel should be in 22 gauge construction. Cabinets are tested as per SEFA 8M standard from a SEFA approved Lab and also tested as per EN 14727 from a third party testing agencyDimensions: W=600 mm, 750 mm, 900mm , D = 530mm, H = 875 mm Configurations: continuous storages MOC: MSCRCA: IS – 513 (1994) Thickness: LH/RH side panels, shutter front, Bottom panel, Top front, Drawer separator, shelf, Alignment channel is of 1.2mm thk. Removable Back panel, Shutter cover, Fr. Rack strip, Top cover panel is of 0.8mmthk Finish: The complete M.S. material of cabinet should be pre-treated (degreased, Zinc phosphated) and epoxy powder coated for better corrosion resistance. The thickness of powder coat should be 45-50 microns, which passes the test of Salt Spray for 1000 hours. It should have a high temperature withstanding capacity with excellent electrical insulation properties.The rear portion of above accessories which is in contact with live metal should be made from thermo set material which will not melt on heating.Handle: Anodized Aluminum Recessed-Type, CTC: 160.0mm Lock: Units have a locking facility with 180° and 10 lever cam lock mechanism (except for sink and corner unit) Hinge: SS Hinge .Screw: SS 304.Shutter : should be of twin-type construction with sound dampening effect using profill. Shutter cover should be equipped with Bump on for sound dampening. Base Moulding should be made of PVC with corner clips. Ball Slide: 500mm Length Shutter should have provision of roller catch. COVER / FILLER PANELS All side cover panels and back panels, filler panels should be made from CRCA MS panels of 1.0mm thickness with pure epoxy powder coating . SERVICE FITTINGS AND ACCESSORIES Service fittings should be laboratory grade, and water faucets and valve bodies should be cast red brass alloy or bronze forgings, all fittings should be powder plated unless specified otherwise. Service Indexes: Fittings should be identified with service indexes in the color coding as per DIN 12920. ELECTRICAL ACCESSORIES (6/16 A SWITCHES & SOCKETS) : These are made of High gloss virgin grade engineering thermoplastics to impart a defect free surface. they impart excellent electrical insulation properties i.e. do not melt on heating or catches fire. Owing to this all electrical switches and sockets are capable of handling higher currents and operating temperatures. Front plates can be changed at any time with ease without disturbing the wiring to quickly and economically match changes in the surroundings.WORKTOP : Jet Black Granite: It should be 19mm (+/- 2mm) thick Jet Black Granite worktop. The exposed edges of the worktop should be chamfered and smoothened. The bottom of the worktop should be polished and there should be a V-groove throughout the length of the exposed edges to protect the cabinets from coming in contact with the spillages. The overhang on the storage cabinet is 25 mm at the front side and 30 mm at the sides. The backing material used is a neoprene mat of 6 mm thickness. as directed by Engineer In-charge(As per specified in Technical specification of furniture Page No.30 of NIT) |
| 102 | Providing supply installation of WALL TABLE WITH SINK - 12 16116mmL X 770mmD X 900mmH WITH ELECTRICAL TRUNKINGConstruction : Floor based Welded cabinet system having storage body should be flush face construction with intersection of vertical and horizontal members like LH and RH side panel along with front horizontal channel, back panel and bottom panel. It should be relocated anywhere easily as it is an independent unit. Cabinet should of square non-sharp edge construction. Doors should be assembled with SS-304 hinge assembly. Removable back panel should be provided to easily access the service lines running behind the cabinet benches. Intermediate horizontal channels should be provided between door and drawer. Toe-space of 90mm X 90mm is provided at front-bottom side of cabinet. Levelers are provided for easy leveling of welded cabinet. Shelf should be eight-bend panel with 20mm height. Drawer tray should be of single piece construction. Drawer should be well supported on LH and RH ball slide suspension system. Steel door and drawer front should be of double wall construction with sound dampening material filled inside. Doors should be easily removable and hinges should be easily replaceable. Knee space panel should be in 22 gauge construction. Cabinets are tested as per SEFA 8M standard from a SEFA approved Lab and also tested as per EN 14727 from a third party testing agencyDimensions: W=600 mm, 750 mm, 900mm , D = 530mm, H = 875 mm Configurations: continuous storages MOC: MSCRCA: IS – 513 (1994) Thickness: LH/RH side panels, shutter front, Bottom panel, Top front, Drawer separator, shelf, Alignment channel is of 1.2mm thk. Removable Back panel, Shutter cover, Fr. Rack strip, Top cover panel is of 0.8mmthk Finish: The complete M.S. material of cabinet should be pre-treated (degreased, Zinc phosphated) and epoxy powder coated for better corrosion resistance. The thickness of powder coat should be 45-50 microns, which passes the test of Salt Spray for 1000 hours. It should have a high temperature withstanding capacity with excellent electrical insulation properties.The rear portion of above accessories which is in contact with live metal should be made from thermo set material which will not melt on heating.Handle: Anodized Aluminum Recessed-Type, CTC: 160.0mm Lock: Units have a locking facility with 180° and 10 lever cam lock mechanism (except for sink and corner unit) Hinge: SS Hinge .Screw: SS 304.Shutter : should be of twin-type construction with sound dampening effect using profill. Shutter cover should be equipped with Bump on for sound dampening. Base Moulding should be made of PVC with corner clips. Ball Slide: 500mm Length Shutter should have provision of roller catch. COVER / FILLER PANELS All side cover panels and back panels, filler panels should be made from CRCA MS panels of 1.0mm thickness with pure epoxy powder coating . SERVICE FITTINGS AND ACCESSORIES Service fittings should be laboratory grade, and water faucets and valve bodies should be cast red brass alloy or bronze forgings, all fittings should be powder plated unless specified otherwise. Service Indexes: Fittings should be identified with service indexes in the color coding as per DIN 12920. ELECTRICAL ACCESSORIES (6/16 A SWITCHES & SOCKETS) : These are made of High gloss virgin grade engineering thermoplastics to impart a defect free surface. they impart excellent electrical insulation properties i.e. do not melt on heating or catches fire. Owing to this all electrical switches and sockets are capable of handling higher currents and operating temperatures. Front plates can be changed at any time with ease without disturbing the wiring to quickly and economically match changes in the surroundings.PP Sink: ,Polypropylene Molded Sinks: Made up of 5 mm thick high density and elastic poly propylene with good resistance to organic solvents. Sink - Bowl size to be a minimum of (L x W x D) 560 x 355 x 300 mm. Faucet - 3-way type faucet as per approved make WORKTOP : Jet Black Granite: It should be 19mm (+/- 2mm) thick Jet Black Granite worktop. The exposed edges of the worktop should be chamfered and smoothened. The bottom of the worktop should be polished and there should be a V-groove throughout the length of the exposed edges to protect the cabinets from coming in contact with the spillages. The overhang on the storage cabinet is 25 mm at the front side and 30 mm at the sides. The backing material used is a neoprene mat of 6 mm thickness. as directed by Engineer In-charge(As per specified in Technical specification of furniture Page No.30 of NIT) |
| 103 | Providing supply installation of WALL TABLE WITH SINK - 12 16968mmL X 770mmD X 900mmH WITH ELECTRICAL TRUNKING , LPG VALVEConstruction : Floor based Welded cabinet system having storage body should be flush face construction with intersection of vertical and horizontal members like LH and RH side panel along with front horizontal channel, back panel and bottom panel. It should be relocated anywhere easily as it is an independent unit. Cabinet should of square non-sharp edge construction. Doors should be assembled with SS-304 hinge assembly. Removable back panel should be provided to easily access the service lines running behind the cabinet benches. Intermediate horizontal channels should be provided between door and drawer. Toe-space of 90mm X 90mm is provided at front-bottom side of cabinet. Levelers are provided for easy leveling of welded cabinet. Shelf should be eight-bend panel with 20mm height. Drawer tray should be of single piece construction. Drawer should be well supported on LH and RH ball slide suspension system. Steel door and drawer front should be of double wall construction with sound dampening material filled inside. Doors should be easily removable and hinges should be easily replaceable. Knee space panel should be in 22 gauge construction. Cabinets are tested as per SEFA 8M standard from a SEFA approved Lab and also tested as per EN 14727 from a third party testing agencyDimensions: W=600 mm, 750 mm, 900mm , D = 530mm, H = 875 mm Configurations: continuous storages MOC: MSCRCA: IS – 513 (1994) Thickness: LH/RH side panels, shutter front, Bottom panel, Top front, Drawer separator, shelf, Alignment channel is of 1.2mm thk. Removable Back panel, Shutter cover, Fr. Rack strip, Top cover panel is of 0.8mmthk Finish: The complete M.S. material of cabinet should be pre-treated (degreased, Zinc phosphated) and epoxy powder coated for better corrosion resistance. The thickness of powder coat should be 45-50 microns, which passes the test of Salt Spray for 1000 hours. It should have a high temperature withstanding capacity with excellent electrical insulation properties.The rear portion of above accessories which is in contact with live metal should be made from thermo set material which will not melt on heating.Handle: Anodized Aluminum Recessed-Type, CTC: 160.0mm Lock: Units have a locking facility with 180° and 10 lever cam lock mechanism (except for sink and corner unit) Hinge: SS Hinge .Screw: SS 304.Shutter : should be of twin-type construction with sound dampening effect using profill. Shutter cover should be equipped with Bump on for sound dampening. Base Moulding should be made of PVC with corner clips. Ball Slide: 500mm Length Shutter should have provision of roller catch. COVER / FILLER PANELS All side cover panels and back panels, filler panels should be made from CRCA MS panels of 1.0mm thickness with pure epoxy powder coating . SERVICE FITTINGS AND ACCESSORIES Service fittings should be laboratory grade, and water faucets and valve bodies should be cast red brass alloy or bronze forgings, all fittings should be powder plated unless specified otherwise. Service Indexes: Fittings should be identified with service indexes in the color coding as per DIN 12920. ELECTRICAL ACCESSORIES (6/16 A SWITCHES & SOCKETS) : These are made of High gloss virgin grade engineering thermoplastics to impart a defect free surface. they impart excellent electrical insulation properties i.e. do not melt on heating or catches fire. Owing to this all electrical switches and sockets are capable of handling higher currents and operating temperatures. Front plates can be changed at any time with ease without disturbing the wiring to quickly and economically match changes in the surroundings.PP Sink: ,Polypropylene Molded Sinks: Made up of 5 mm thick high density and elastic poly propylene with good resistance to organic solvents. Sink - Bowl size to be a minimum of (L x W x D) 560 x 355 x 300 mm. Faucet - 3-way type faucet as per approved make WORKTOP : Jet Black Granite: It should be 19mm (+/- 2mm) thick Jet Black Granite worktop. The exposed edges of the worktop should be chamfered and smoothened. The bottom of the worktop should be polished and there should be a V-groove throughout the length of the exposed edges to protect the cabinets from coming in contact with the spillages. The overhang on the storage cabinet is 25 mm at the front side and 30 mm at the sides. The backing material used is a neoprene mat of 6 mm thickness. as directed by Engineer In-charge(As per specified in Technical specification of furniture Page No.30 of NIT) |
| 104 | Providing supply installation of WALL TABLE WITH SINK - 12 4385mmL X 770mmD X 900mmH WITH ELECTRICAL TRUNKING , LPG VALVE & PEG BOARDConstruction : Floor based Welded cabinet system having storage body should be flush face construction with intersection of vertical and horizontal members like LH and RH side panel along with front horizontal channel, back panel and bottom panel. It should be relocated anywhere easily as it is an independent unit. Cabinet should of square non-sharp edge construction. Doors should be assembled with SS-304 hinge assembly. Removable back panel should be provided to easily access the service lines running behind the cabinet benches. Intermediate horizontal channels should be provided between door and drawer. Toe-space of 90mm X 90mm is provided at front-bottom side of cabinet. Levelers are provided for easy leveling of welded cabinet. Shelf should be eight-bend panel with 20mm height. Drawer tray should be of single piece construction. Drawer should be well supported on LH and RH ball slide suspension system. Steel door and drawer front should be of double wall construction with sound dampening material filled inside. Doors should be easily removable and hinges should be easily replaceable. Knee space panel should be in 22 gauge construction. Cabinets are tested as per SEFA 8M standard from a SEFA approved Lab and also tested as per EN 14727 from a third party testing agencyDimensions: W=600 mm, 750 mm, 900mm , D = 530mm, H = 875 mm Configurations: continuous storages MOC: MSCRCA: IS – 513 (1994) Thickness: LH/RH side panels, shutter front, Bottom panel, Top front, Drawer separator, shelf, Alignment channel is of 1.2mm thk. Removable Back panel, Shutter cover, Fr. Rack strip, Top cover panel is of 0.8mmthk Finish: The complete M.S. material of cabinet should be pre-treated (degreased, Zinc phosphated) and epoxy powder coated for better corrosion resistance. The thickness of powder coat should be 45-50 microns, which passes the test of Salt Spray for 1000 hours. It should have a high temperature withstanding capacity with excellent electrical insulation properties.The rear portion of above accessories which is in contact with live metal should be made from thermo set material which will not melt on heating.Handle: Anodized Aluminum Recessed-Type, CTC: 160.0mm Lock: Units have a locking facility with 180° and 10 lever cam lock mechanism (except for sink and corner unit) Hinge: SS Hinge .Screw: SS 304.Shutter : should be of twin-type construction with sound dampening effect using profill. Shutter cover should be equipped with Bump on for sound dampening. Base Moulding should be made of PVC with corner clips. Ball Slide: 500mm Length Shutter should have provision of roller catch. COVER / FILLER PANELS All side cover panels and back panels, filler panels should be made from CRCA MS panels of 1.0mm thickness with pure epoxy powder coating . SERVICE FITTINGS AND ACCESSORIES Service fittings should be laboratory grade, and water faucets and valve bodies should be cast red brass alloy or bronze forgings, all fittings should be powder plated unless specified otherwise. Service Indexes: Fittings should be identified with service indexes in the color coding as per DIN 12920. ELECTRICAL ACCESSORIES (6/16 A SWITCHES & SOCKETS) : These are made of High gloss virgin grade engineering thermoplastics to impart a defect free surface. they impart excellent electrical insulation properties i.e. do not melt on heating or catches fire. Owing to this all electrical switches and sockets are capable of handling higher currents and operating temperatures. Front plates can be changed at any time with ease without disturbing the wiring to quickly and economically match changes in the surroundings.PP Sink: ,Polypropylene Molded Sinks: Made up of 5 mm thick high density and elastic poly propylene with good resistance to organic solvents. Sink - Bowl size to be a minimum of (L x W x D) 560 x 355 x 300 mm. Faucet - 3-way type faucet as per approved make PEGBOARD: SS Peg Board with 33 pp Pegs & Tray (Size: 600 mm x 600 mm x 15 mm)WORKTOP : Jet Black Granite: It should be 19mm (+/- 2mm) thick Jet Black Granite worktop. The exposed edges of the worktop should be chamfered and smoothened. The bottom of the worktop should be polished and there should be a V-groove throughout the length of the exposed edges to protect the cabinets from coming in contact with the spillages. The overhang on the storage cabinet is 25 mm at the front side and 30 mm at the sides. The backing material used is a neoprene mat of 6 mm thickness. as directed by Engineer In-charge(As per specified in Technical specification of furniture Page No.30 of NIT) |
| 105 | Providing supply installation of WALL TABLE WITH SINK - 15 16818mmL X 920mmD X 900mmH WITH ELECTRICAL TRUNKINGConstruction : Floor based Welded cabinet system having storage body should be flush face construction with intersection of vertical and horizontal members like LH and RH side panel along with front horizontal channel, back panel and bottom panel. It should be relocated anywhere easily as it is an independent unit. Cabinet should of square non-sharp edge construction. Doors should be assembled with SS-304 hinge assembly. Removable back panel should be provided to easily access the service lines running behind the cabinet benches. Intermediate horizontal channels should be provided between door and drawer. Toe-space of 90mm X 90mm is provided at front-bottom side of cabinet. Levelers are provided for easy leveling of welded cabinet. Shelf should be eight-bend panel with 20mm height. Drawer tray should be of single piece construction. Drawer should be well supported on LH and RH ball slide suspension system. Steel door and drawer front should be of double wall construction with sound dampening material filled inside. Doors should be easily removable and hinges should be easily replaceable. Knee space panel should be in 22 gauge construction. Cabinets are tested as per SEFA 8M standard from a SEFA approved Lab and also tested as per EN 14727 from a third party testing agencyDimensions: W=600 mm, 750 mm, 900mm , D = 530mm, H = 875 mm Configurations: continuous storages MOC: MSCRCA: IS – 513 (1994) Thickness: LH/RH side panels, shutter front, Bottom panel, Top front, Drawer separator, shelf, Alignment channel is of 1.2mm thk. Removable Back panel, Shutter cover, Fr. Rack strip, Top cover panel is of 0.8mmthk Finish: The complete M.S. material of cabinet should be pre-treated (degreased, Zinc phosphated) and epoxy powder coated for better corrosion resistance. The thickness of powder coat should be 45-50 microns, which passes the test of Salt Spray for 1000 hours. It should have a high temperature withstanding capacity with excellent electrical insulation properties.The rear portion of above accessories which is in contact with live metal should be made from thermo set material which will not melt on heating.Handle: Anodized Aluminum Recessed-Type, CTC: 160.0mm Lock: Units have a locking facility with 180° and 10 lever cam lock mechanism (except for sink and corner unit) Hinge: SS Hinge .Screw: SS 304.Shutter : should be of twin-type construction with sound dampening effect using profill. Shutter cover should be equipped with Bump on for sound dampening. Base Moulding should be made of PVC with corner clips. Ball Slide: 500mm Length Shutter should have provision of roller catch. COVER / FILLER PANELS All side cover panels and back panels, filler panels should be made from CRCA MS panels of 1.0mm thickness with pure epoxy powder coating . SERVICE FITTINGS AND ACCESSORIES Service fittings should be laboratory grade, and water faucets and valve bodies should be cast red brass alloy or bronze forgings, all fittings should be powder plated unless specified otherwise. Service Indexes: Fittings should be identified with service indexes in the color coding as per DIN 12920. ELECTRICAL ACCESSORIES (6/16 A SWITCHES & SOCKETS) : These are made of High gloss virgin grade engineering thermoplastics to impart a defect free surface. they impart excellent electrical insulation properties i.e. do not melt on heating or catches fire. Owing to this all electrical switches and sockets are capable of handling higher currents and operating temperatures. Front plates can be changed at any time with ease without disturbing the wiring to quickly and economically match changes in the surroundings.PP Sink: ,Polypropylene Molded Sinks: Made up of 5 mm thick high density and elastic poly propylene with good resistance to organic solvents. Sink - Bowl size to be a minimum of (L x W x D) 560 x 355 x 300 mm. Faucet - 3-way type faucet as per approved make WORKTOP : Jet Black Granite: It should be 19mm (+/- 2mm) thick Jet Black Granite worktop. The exposed edges of the worktop should be chamfered and smoothened. The bottom of the worktop should be polished and there should be a V-groove throughout the length of the exposed edges to protect the cabinets from coming in contact with the spillages. The overhang on the storage cabinet is 25 mm at the front side and 30 mm at the sides. The backing material used is a neoprene mat of 6 mm thickness. as directed by Engineer In-charge(As per specified in Technical specification of furniture Page No.30 of NIT) |
| 106 | Providing supply installation of WALL TABLE WITH SINK - 15 4385mmL X 770mmD X 900mmH WITH ELECTRICAL TRUNKINGConstruction : Floor based Welded cabinet system having storage body should be flush face construction with intersection of vertical and horizontal members like LH and RH side panel along with front horizontal channel, back panel and bottom panel. It should be relocated anywhere easily as it is an independent unit. Cabinet should of square non-sharp edge construction. Doors should be assembled with SS-304 hinge assembly. Removable back panel should be provided to easily access the service lines running behind the cabinet benches. Intermediate horizontal channels should be provided between door and drawer. Toe-space of 90mm X 90mm is provided at front-bottom side of cabinet. Levelers are provided for easy leveling of welded cabinet. Shelf should be eight-bend panel with 20mm height. Drawer tray should be of single piece construction. Drawer should be well supported on LH and RH ball slide suspension system. Steel door and drawer front should be of double wall construction with sound dampening material filled inside. Doors should be easily removable and hinges should be easily replaceable. Knee space panel should be in 22 gauge construction. Cabinets are tested as per SEFA 8M standard from a SEFA approved Lab and also tested as per EN 14727 from a third party testing agencyDimensions: W=600 mm, 750 mm, 900mm , D = 530mm, H = 875 mm Configurations: continuous storages MOC: MSCRCA: IS – 513 (1994) Thickness: LH/RH side panels, shutter front, Bottom panel, Top front, Drawer separator, shelf, Alignment channel is of 1.2mm thk. Removable Back panel, Shutter cover, Fr. Rack strip, Top cover panel is of 0.8mmthk Finish: The complete M.S. material of cabinet should be pre-treated (degreased, Zinc phosphated) and epoxy powder coated for better corrosion resistance. The thickness of powder coat should be 45-50 microns, which passes the test of Salt Spray for 1000 hours. It should have a high temperature withstanding capacity with excellent electrical insulation properties.The rear portion of above accessories which is in contact with live metal should be made from thermo set material which will not melt on heating.Handle: Anodized Aluminum Recessed-Type, CTC: 160.0mm Lock: Units have a locking facility with 180° and 10 lever cam lock mechanism (except for sink and corner unit) Hinge: SS Hinge .Screw: SS 304.Shutter : should be of twin-type construction with sound dampening effect using profill. Shutter cover should be equipped with Bump on for sound dampening. Base Moulding should be made of PVC with corner clips. Ball Slide: 500mm Length Shutter should have provision of roller catch. COVER / FILLER PANELS All side cover panels and back panels, filler panels should be made from CRCA MS panels of 1.0mm thickness with pure epoxy powder coating . SERVICE FITTINGS AND ACCESSORIES Service fittings should be laboratory grade, and water faucets and valve bodies should be cast red brass alloy or bronze forgings, all fittings should be powder plated unless specified otherwise. Service Indexes: Fittings should be identified with service indexes in the color coding as per DIN 12920. ELECTRICAL ACCESSORIES (6/16 A SWITCHES & SOCKETS) : These are made of High gloss virgin grade engineering thermoplastics to impart a defect free surface. they impart excellent electrical insulation properties i.e. do not melt on heating or catches fire. Owing to this all electrical switches and sockets are capable of handling higher currents and operating temperatures. Front plates can be changed at any time with ease without disturbing the wiring to quickly and economically match changes in the surroundings.PP Sink: ,Polypropylene Molded Sinks: Made up of 5 mm thick high density and elastic poly propylene with good resistance to organic solvents. Sink - Bowl size to be a minimum of (L x W x D) 560 x 355 x 300 mm. Faucet - 3-way type faucet as per approved make WORKTOP : Jet Black Granite: It should be 19mm (+/- 2mm) thick Jet Black Granite worktop. The exposed edges of the worktop should be chamfered and smoothened. The bottom of the worktop should be polished and there should be a V-groove throughout the length of the exposed edges to protect the cabinets from coming in contact with the spillages. The overhang on the storage cabinet is 25 mm at the front side and 30 mm at the sides. The backing material used is a neoprene mat of 6 mm thickness. as directed by Engineer In-charge(As per specified in Technical specification of furniture Page No.30 of NIT) |
| 107 | Providing supply installation of WALL TABLE WITH SINK - 3 8115mmL X 770mmD X 900mmH WITH ELECTRICAL TRUNKINGConstruction : Floor based Welded cabinet system having storage body should be flush face construction with intersection of vertical and horizontal members like LH and RH side panel along with front horizontal channel, back panel and bottom panel. It should be relocated anywhere easily as it is an independent unit. Cabinet should of square non-sharp edge construction. Doors should be assembled with SS-304 hinge assembly. Removable back panel should be provided to easily access the service lines running behind the cabinet benches. Intermediate horizontal channels should be provided between door and drawer. Toe-space of 90mm X 90mm is provided at front-bottom side of cabinet. Levelers are provided for easy leveling of welded cabinet. Shelf should be eight-bend panel with 20mm height. Drawer tray should be of single piece construction. Drawer should be well supported on LH and RH ball slide suspension system. Steel door and drawer front should be of double wall construction with sound dampening material filled inside. Doors should be easily removable and hinges should be easily replaceable. Knee space panel should be in 22 gauge construction. Cabinets are tested as per SEFA 8M standard from a SEFA approved Lab and also tested as per EN 14727 from a third party testing agencyDimensions: W=600 mm, 750 mm, 900mm , D = 530mm, H = 875 mm Configurations:Continuous storage MOC: MSCRCA: IS – 513 (1994) Thickness: LH/RH side panels, shutter front, Bottom panel, Top front, Drawer separator, shelf, Alignment channel is of 1.2mm thk. Removable Back panel, Shutter cover, Fr. Rack strip, Top cover panel is of 0.8mmthk Finish: The complete M.S. material of cabinet should be pre-treated (degreased, Zinc phosphated) and epoxy powder coated for better corrosion resistance. The thickness of powder coat should be 45-50 microns, which passes the test of Salt Spray for 1000 hours. It should have a high temperature withstanding capacity with excellent electrical insulation properties.The rear portion of above accessories which is in contact with live metal should be made from thermo set material which will not melt on heating.Handle: Anodized Aluminum Recessed-Type, CTC: 160.0mm Lock: Units have a locking facility with 180° and 10 lever cam lock mechanism (except for sink and corner unit) Hinge: SS Hinge .Screw: SS 304.Shutter : should be of twin-type construction with sound dampening effect using profill. Shutter cover should be equipped with Bump on for sound dampening. Base Moulding should be made of PVC with corner clips. Ball Slide: 500mm Length Shutter should have provision of roller catch. COVER / FILLER PANELS All side cover panels and back panels, filler panels should be made from CRCA MS panels of 1.0mm thickness with pure epoxy powder coating . SERVICE FITTINGS AND ACCESSORIES Service fittings should be laboratory grade, and water faucets and valve bodies should be cast red brass alloy or bronze forgings, all fittings should be powder plated unless specified otherwise. Service Indexes: Fittings should be identified with service indexes in the color coding as per DIN 12920. ELECTRICAL ACCESSORIES (6/16 A SWITCHES & SOCKETS) : These are made of High gloss virgin grade engineering thermoplastics to impart a defect free surface. they impart excellent electrical insulation properties i.e. do not melt on heating or catches fire. Owing to this all electrical switches and sockets are capable of handling higher currents and operating temperatures. Front plates can be changed at any time with ease without disturbing the wiring to quickly and economically match changes in the surroundings.WORKTOP : Jet Black Granite: It should be 19mm (+/- 2mm) thick Jet Black Granite worktop. The exposed edges of the worktop should be chamfered and smoothened. The bottom of the worktop should be polished and there should be a V-groove throughout the length of the exposed edges to protect the cabinets from coming in contact with the spillages. The overhang on the storage cabinet is 25 mm at the front side and 30 mm at the sides. The backing material used is a neoprene mat of 6 mm thickness. as directed by Engineer In-charge(As per specified in Technical specification of furniture Page No.30 of NIT) |
| 108 | Providing ,Supplying and fixing of Interactive Display Monitor : Screen Size 86\\" or Higher, Native Resolution 3840 x 2160 (UHD), Brightness Minimum 400cd/m2 with Interactive and protection Glass , Contrast Ratio 1,100 :1 or Higher, Viewing Angle(H x V) 178 x 178, or Higher Surface Treatment With Min Anti-glare treatment Min Input ports HDMI-2 or above ,USB(3.0)-2,USB-(2.0)-1 or above ,OPS Slot-1, USB C(Front) Built in Touch type IR spread /P Cap/Incell/In glass Protection Glass Thickness 3T (Anti-Glare) or Higher Operating System Built-in OS Android 14.0 or better with EDLA Certifified, Multi touch point Min 20 Points or Higher, Min Interactive Features White Board & Standard Interactive features, WritingPen,Screen Capture, Inbuilt Storage, Tool Bar, Feature like Air Class for Online test/Quiz or similar ,USB Block feature for safety ,Dual Pen support , Bluetooth connectivity,Panel System on Chip Minimum Octa core processor with 8GB RAM and Internal Memory 64GB or higher Media share Screen Share/Mira cast to Connect TAB/Mobile, Web Browser ,Connectivity Wi-Fi Built in Audio Power Speakers with Min 30 W(15 W x 2) or higher Power Supply 100-240V~, 50/60Hz , Product Quality Certifications BIS certified and offered product should be Make in India product , All accessories like Table stand, Remote , Wall mounting Kit, all required Cables including Power cable suitable with adopter and installation in Classroom with Touch Pen min 2, BIS ,ISO 14001, ISO 9001, ISO 45000,UL, FCC, ROHS certification ,Device Management Software for every Interactive Panel with 3 years License, Ability to manage & maintain all deployed IFPS connected over LAN/WAN, including the functionality-Ability to manage & maintain all deployed IFPS connected over LAN/WAN, including the functionality- Turn on/off the panel, Change input/ volume Warranty 3 years `Installation type Wall mount. as directed by Engineer In-charge(As per specified in Technical specification of furniture Page No.30 of NIT) |
| 109 | Providing ,Supplying and fixing of Windows Base OPS :- Processor With Intel® Tigerlake-H, TDP. 35W, OPS Featues With Intel® OPS-C Standard Module. JAE 80-pin connection,Dual SO-DIMM DDR4,M.2 SSD Module, M.2 WiFi Module,HDMI 2.0, DP 1.2. CPU :- I5-1145/11500H/11500B I7-11700B/12450H/1235U/1335U, PCH :- HM570/WM590, Memory :- 2 x SO-DIMM DDR4 /2666/3200 MHz, Max 32GB, Storage :- 1 x M.2 2280 SSD, Nvme/SATA - 1 x M.2 2280 SSD, SATA - Totally 2 SSD Slot, Graphics :- Intel® UHD Graphics, Wireless :- 1 x M.2 2230 WIFI/BT Module, Audio :- Realtek ALC897 HD Audio IC, Network :- Realtek Gigabit Ethernet , Interfaces Frontside :- ( 1 x USB3.0 Type-C , 6 x USB3.0 Type-A , 1 x RJ45 10/100/1000M , 1 x HDMI 1.4 out, 1 x DP 1.2 out , 1 x 3.5mm Line out , 1 x 3.5mm Mic in, 2 x WIFI/BT ANT , 1 x Power button , 1 x Recover button , 1 x Power LED , 1 x SSD LED) JAE 80-pin :- ( 1 x HDMI 2.0 out , , USB2.0/3.0 , TTL ) . Power :- 12-19V DC IN , OS Support :- Windows 10, Windows 11. Warranty :- 3 Year as directed by Engineer In-charge(As per specified in Technical specification of furniture Page No.30 of NIT) |
| 110 | Providing ,Supplying and fixing of Horizontal Sliding Board Resin for 86 Inch Interactive Display PanelWith four board systemFixed Board – Green/White ColorSliding Board – White/Green ColorOuter Length of Frame : 4125mmOuter width of Frame : 1300mmThickness of Frame(Depth): 210 mmFrame is made of Aluminum with Bronze color anodizing.Total 4 boards (2 boards are fixed and 2 boards are movable with lock & key arrangement)Dimension of Fixed/Sliding board - 1050 mm x 1205 mmSpecs for Fixed Boards -1. Top Surface – Resin2. Core Material - Particle Board3. Backing surface - GI sheet with thickness of 0.2 ‐ 0.3mmSpecs for Sliding Boards -1. Top Surface - 0.3 mm Ceramic surface2. Core Material - Paper Honeycomb/Particle Board3. Backing surface - GI sheet with thickness of 0.2 ‐ 0.3mmSuitable for Interactive Board of Size - TV: 86 Inch DiagonalDimensional Tolerance for Boards - +/- 20 mm as directed by Engineer In-charge(As per specified in Technical specification of furniture Page No.30 of NIT) |
| 111 | Providing ,Supplying and fixing of 5 Meter HDMI Cable , 4K60 4:4:4 18Gbps Bandwidth, gold plated High Retention Lgrip connectors, Oxygen Free Copper cable, overall cable diameter 8mm. as directed by Engineer In-charge(As per specified in Technical specification of furniture Page No.30 of NIT) |
| 112 | Providing and Fixing Installation of Smart Board Interactive Display Monitor, Windows Base OPS, Horizontal Sliding Board Resin for 86 Inch Interactive Display Panel & HDMI Cable with complete operation as directed by Engineer In-charge. as directed by Engineer In-charge(As per specified in Technical specification of furniture Page No.30 of NIT) Please Enable Macros to View BoQ information |
AI Tender Summary
Tender Timeline
Jul 14, 2026
11:30 IST
Tender Published
Tender notice published.
CompletedAug 07, 2026
17:00 IST
Bid Submission Deadline
Online submission via eProcurement portal.
Upcoming · 22 daysAug 07, 2026
Bid Opening Date
Technical bids will be opened and evaluated.
Upcoming · 22 daysTender Documents
Download All (ZIP) ↓
Disclaimer
We takes all possible care for accurate & authentic tender information. However users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender