Tender For special Repair To Bldg No T-449, T-831 And Allied Works Near Mi Room And Demo Coy And Certain Major And Minor Works At Cijws School Vairengte
Tender Value
46.20 Lakhs
Estimated cost
Bid Submission
05 Aug 2026
8 days left
EMD
92400
Bank guarantee accepted
Document Fee
500
Non-refundable
Tender Type
Online
Tender Overview
Organization
Tender ID
Competition Type
NCB
Bidding Type
Tender
Location / State
Kolasib → Mizoram
EMD Exemption
Available
Quantity
Not Available
Website
Contact Person
Address
Project Description
Tender for special Repair To Bldg No T-449, T-831 And Allied Works Near Mi Room And Demo Coy And Certain Major And Minor Works At Cijws School Vairengte
BOQ
| Sl. No. | Item Description |
| 1 | B & R Division Items |
| 2 | Demolition of un-reinforced cement concrete in ground floor and paving not exceeding 15 cm thick (below or above ground level) complete all as specified and directed. |
| 3 | Demolition of reinforced cement concrete in roofs, floors (other than ground floors), beams, staircases, landing, chajjas and similar suspended work complete all as specified and directed. |
| 4 | Demolition of brick work or stone/ boulder masonry, built in cement mortar including all quoins, pillars etc. complete all as specified and as directed. |
| 5 | Dismantling floor, hearth or wall tilling including cement mortar bedding (but not backing) removing serviceable tiles to stores and rubbish off the premises. |
| 6 | Demolition of reed lathing, single or double including battens and plaster or chiken wire lathing all as specified. |
| 7 | Dismantling asbestos cement sheet( Semi corrugated, corrugated sheeting) any gauge or any thickness as in roof covering etc. including all necessary staging / scaffolding, etc. as required complete all as specified and as directed. |
| 8 | Dismantling of timber scantling 40 Sqcm and over in section, in any position in unframed work complete all as specified and directed. |
| 9 | Dismantling wall and ceiling boards (fibre, pulb, insulation etc) or insulation boards slabs/blankets any thickness including cover fillets all as specified and as directed. |
| 10 | Dismantling boarding any description fixed in any position with nails all as specified. |
| 11 | Dismantling SGW/asbestos cement/PVC pipe 50/75/100 mm dia including clamps complete all as specified and directed. |
| 12 | Dismantling of cast iron or reinforced concrete drain pipes, jointed in cement mortar and taking out of trenches, if required complete all as specified and directed. |
| 13 | Taking down cement plaster on brick or stone walls etc, including raking out joints, hacking for key scrubing down with water etc complete all as specified and as directed. |
| 14 | Taking down chowkhats or frame with shutters (without taking off shutters from frame) each not exceeding 1.50 Sqm each complete all as specified. |
| 15 | Taking down Chowkhats or frames with shutters exceeding 1.5 Sqm but not exceeding 4 Sqm each (without taking off shutters from the frame) complete all as specified. |
| 16 | Taking up or down 15mm dia GI steel tubing and connections, including cleaning for refixing or removal to store complete all as specified and as directed. |
| 17 | Taking up or down 20mm dia GI steel tubing and connections, including cleaning for refixing or removal to store complete all as specified and as directed. |
| 18 | Surface dressing n exc 15 cm deep and getting out in soft / lose soil complete all as specified |
| 19 | Rough excavation over areas not exceeding 1.5m deep and getting out hard/ dense type of soil complete all as specified and directed. |
| 20 | Excavating in trenches, n exc 1.50 m wide and n exc 1.5 m in depth; for foundation, etc. or for shafts, wells, cesspits, manholes, pier holes, etc. n exc 10 sq m on plan and n exc 1.5 m in depth and getting out soft/ loose type of soil complete all as specified and directed. |
| 21 | Returning, filling in trenches including spreading, leveling watering and ramming in layers not exceeding 25cm all as specified. |
| 22 | Removing of surplus soil not exceeding 50 m and deposited where directed at a level not exceeding 1.50m above the starting point all as specified. |
| 23 | Removing of surplus soil not exceeding 50 m and deposited where directed at a level not exceeding 1.50m above the starting point all as specified. |
| 24 | M&L for Hardcore broken stone of gauge exc 40mm and n exc 63mm deposited spread and levelled in layers n exc 15cm thick watered and rammed to a true surface complete all as specified and directed. |
| 25 | M&L for PCC (1:4:8), Type D2 using 40 mm graded stone aggregate as in foundations, sub-base,filling and mass concrete complete all as specified. |
| 26 | M & L for 75mm thick plain cement concrete 1:3:6 type C2 (using 40mm graded stone aggregate) as in plinth protection finished even and fair without using extra cement laid in panels and joints filled with bituminous mastic filling with 1 part of bitumen and 3 part of sand complete all as specified and directed. |
| 27 | M & L for 75mm thick plain cement concrete 1:3:6 type C1 (using 20mm graded stone aggregate) as in sub base to floors/path and pavement complete all as specified and directed. |
| 28 | Use and waste formwork to sides of concrete foundations, footings, bases of columns, raft and raft beams, sides and soffits (if any) of foundation and plinth beams; and similar work; vertical or to batter rough finished flat surfaces of concrete complete all as specified and as directed. |
| 29 | Use and waste of formwork to sides of pillars, posts, struts, piers, columns and stanchions for rough finished flat surfaces of concrete all as specified and directed. |
| 30 | Use and waste of formwork to soffits of suspended slabs such as roof slabs, floor slabs, landings and similar work; not exceeding 200mm thick (Horizontal or sloping) complete all as specified and directed |
| 31 | Use and waste Formwork to edges of concrete flats, treads, breaks in floors, window cills, concrete railings, openings in concrete walls, floor and roofs n exc 20 cm wide and sides of RCC/ PCC bands in walls, horizontal or sloping and similar work exc 10cm but n exc 20cm wide all as specified and directed. |
| 32 | Material and labour for Reinforced Cement Concrete M-25 (design mix) using 20 mm graded aggregate as in foundation including rafts, footings, foundation beams, plinth beams, bases for columns etc complete all as specified and directed. |
| 33 | Material and labour for Reinforced Cement Concrete M-25 (design mix) using 20 mm graded aggregate as in column, pillars, piers, posts, and struts complete all as specified and directed. |
| 34 | Material and labour for Reinforced Cement Concrete M-25 (design mix) using 20 mm graded aggregate as in beams, cantilever, lintels over 1.5m complete all as specified and directed. |
| 35 | Material and labour for Reinforced Cement Concrete M-25 (design mix) using 20 mm graded aggregate as in cill band and similar items like complete all as specified and directed. |
| 36 | M & L for Mild Steel TMT Bar 10mm dia and over , cut to length bend to shape as required including cranking, hooking etc and binding with and including mild steel wire (annealed) not less than 0.9 mm dia complete all as specified and directed. |
| 37 | M & L for Mild Steel TMT Bar 6mm to 8mm dia , cut to length bend to shape as required including cranking, hooking etc and binding with and including mild steel wire (annealed) not less than 0.9 mm dia complete all as specified and directed. |
| 38 | M & L for Mild Steel TMT Bar 6mm dia and over up to 10 mm dia as in stirrups, spacers and binders as required including cranking, hooking etc and binding with and including mild steel wire (annealed) not less than 0.9 mm dia complete all as specified and directed |
| 39 | M & L for brickwork with subclass 'B' or locally available best quality old size bricks, straight or curved on plan exc 6 m mean raduis, built in CM (1:6) complete all as specified and directed. |
| 40 | M & L for brick work in cement mortar (1:4) straight or curved on plan to any radius with locally available Subclass ‘B’ old size best quality bricks in half brick thick wall complete all as specified . |
| 41 | M & L for 15 mm thick rendering in cement mortar 1:6 on fair faces of brick wall or concrete surfaces, finished the surfaces even and fair without using extra cement complete all as specified. |
| 42 | M & L for 15 mm thick rendering in cement mortar 1:4 on fair faces of brick wall or concrete surfaces, finished the surfaces even and fair without using extra cement complete all as specified. |
| 43 | M & L rendering 15 mm thick cement mortar (1:4) on fair faces of brick wall or concrete surfaces, in two layer each of 10+5 mm thick & water proofing compound mixed with second layer @ 3% finished fair and even complete all as specified. (Note :WPC measured separately). |
| 44 | M&L for 20 mm thick screed bed of cement mortar 1:6 for laying floor finishes complete all as specified. |
| 45 | Supply only integral water proffing compound WPC complete all as specified. |
| 46 | M & L light vitrified ceramic tiles coloured 7 to 8mm thick (square/ rectangular) area of each tile not exceeding 0.36 sqm, as in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tile over including 15 mm thick screed bed or bedding layers in cement mortar 1:6 for tile over brushing with neat cement slurry as specified |
| 47 | M & L light vitrified ceramic tiles coloured ceramic tiles 7 to 8 mm thick ( square/ rectangular) area of each tiles exc 0.18 sqm but not exc 0.38 sqm as in vertical surfaces of skirting/ dado etc over 10 mm thick rendering in cm (1:4) as backing coat for tile complete all as specified. |
| 48 | M & L Non Skid ceramic tiles coloured 7 to 8mm thick (square/ rectangular) area of each tile exceeding 0.06 but not exceeding 0.11 sqm, as in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tile including 15 mm thick screed bed or bedding layers in cement mortar 1:6 over brushing with neat cement slurry complete all as specified. |
| 49 | M & L Glazed ceramic coloured tiles in vertical surface size 450mm x 300mm x & ( 6mm to 7mm )mm thick set and jointed in neat cement slurry and pointed in white or colour cement to match over & including 10mm thick screed bed or backing coat in cement mortar 1:4 laying of skirting/ dado on walls all as specified and directed. |
| 50 | M&L reflective type rubber moulded chequered coloured cement concrete tile size 300mm X 300mm X 25mm thick, in floors, set, jointed & pointed with neat cement slurry with painted to match colour of tile laid over and including 15mm thick screed bed or bedding layer in cement mortar (1:6) complete all as specified and as directed. |
| 51 | Supply and fix pre-painted galvalume aluminium zinc coating GI based corrugated steel sheet 0.50mm thick of an colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws as specified. |
| 52 | Supply and fix pre-painted galvalume aluminium zinc coating GI based plain steel sheet 0.50mm thick of an colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws as specified. |
| 53 | Supply and fix Framed work such as grills, gratings, etc. with ends of bars or forged into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; framework of water tanks and similar work conforming to Fe.290 Gde-E-165 complete all as specified and directed. |
| 54 | Supply and fix Bands, straps, supports or stays for rainwater, ventilating pipes, including bolts, if required, hooks (stay), heavy, for large gates; hook and pintle hinges large hasps and staples; chains; hand made sliding bolts; clamps; hold fasts; wall ties; hooks for hanging fans; plain angle cleats for securing purlins to wood trusses or rafters; knee piece inserts; two way and three way straps, plate washers,hold fasts, bands, straps, wall ties, plain angle cleats, eaves board frame and similar articles conforming to Fe-290 Gde-E-165 complete all as specified and directed. |
| 55 | Supply and fix mild steel Plates plain cut to required size, forming holes to receive holding down bolt and welded to tubular/square hollow section truss at both ends complete all as specified. |
| 56 | Supply and fix structural steel work in tubular/hollow sections trusses , Purlin , posts, rafter etc including special shaped washer etc. complete using ERW or induction butt welded tubes conforming to IS 1161-1979 grade St.-240 complete all as as specified and directed. |
| 57 | S & F Solid PVC door frame of size 50mm X 47mm made of 5 mm plain colour PVC sheet reinforced with mild steel square tube complete all as specified in clause 8B.3.1 and shown on page 150 of MES Schedule Part-II (2010). |
| 58 | S & F Solid PVC door frame of size 50mm X 120mm made out of 5 mm wood grain printed PVC sheet reinforced with mild steel square tube and edges will be painted to match with printed sheet complete all as specified in clause 8B.3.1 and shown on page 150 of MES Schedule Part-II (2010). |
| 59 | S & F Factory made wire gauzed PVC moulded door shutter 30 mm thick (style) wire gauzed i.e. panel will be of wire gauze in lieu of wood grain printed PVC sheet panel. The wire gauze shall be wrapped on an additional square 8mm M.S. Solid tube and this tube shall be welded to M.S. tubes. The wire gauge shall be stretched to tighten firmly consisting of frame made out of M.S. tubes for top & bottom rails. M.S. frame shall be covered with heat moulded wood grain printed PVC ‘C’ channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and wood grain printed PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail; Panelling of wood grain printed PVC sheet to be fitted in the M.S. frame welded / sealed to the stiles & rails with suitable PVC sheet beading, and joined together with solvent cement, suppling & fixing in the frame at site as per specification & drawing. |
| 60 | S & F Factory Made Solid PVC Moulded Door Shutter, 28 to 30mm thick (stiles), with 2, 4, or 6 raised panel design with 2mm thick prelaminated Moulded PVC Sheet on the front face & 2mm plain colour PVC sheet on back face, supplying & fixing in frame at site as per specification & drawing complete all as specified. |
| 61 | Supply and fix GI wire cloth 0.36 mm nominal dia of wire and average width of aperture 1.18mm and fixed with wooden beeds complete all as specified and directed. |
| 62 | M & L Plain Cement concrete (1:3:6), type C-0 using 12.5mm graded stone aggregate as in filling of hallow steel chowkhats, bed block, fixing of holdfast and similar likes including necessary formwork complete all as specified. |
| 63 | Supply and fix 3 ways sliding anodized aluminium glazed window shutter with frame with the following specification all as specified & directed.(a) Window frame 3 track of size 95mm × 25mm × 1.5mm thick.(b) Stiles and rails of size 35mm × 25mm × 1.5mm.(c) 35mm × 35mm × 1.5mm T section mullion.(d) PVC gasket with 4mm thick tinted glass, incl. aluminium handles with necessary locking arrangement for 02 Nos glazed shutter.(e) Stainless steel wire cloth, 0.36 mm nominal dia of wire and average width of aperture 1.40 mm, fixed with stainless steel wire staples, incl. aluminium handles with necessary locking arrangement for 01 No gauzed shutter.Note: Measurement to be taken as overall width and height of window. No shutter or frame to be measured separately. All necessary accessories including tinted glass and stainless steel wire cloth required for assembling and fixing window at proper place complete are deemed to be inclusive. |
| 64 | Supply and fix 2 way sliding anodized aluminium glazed ventilator shutter with frame consists of following specification all as specified & directed.(a) Ventilator frame 2 track of size 60mm × 25mm × 1.5mm thick.(b) Stiles and rails of size 35mm × 25mm × 1.5mm.(c) 35mm × 35mm × 1.5mm T section mullion.(d) PVC gasket with 4mm thick tinted glass, incl. aluminium handles with necessary locking arrangement.Note: Measurement to be taken as overall width and height of ventilator. No shutter or frame to be measured separately. All necessary accessories including tinted glass required for assembling and fixing window at proper place complete are deemed to be inclusive. |
| 65 | Supply and fix 300mm long Aluminium alloy, anodised, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast-aluminium alloy and fixedcomplete all as specified. |
| 66 | S&F 100mm long SS Butt hinges (ISI marked) with SS screws complete all as specified. |
| 67 | Supply and fix 150 mm long extruded aluminium alloy handles fabricated type anodised complete all as specified & directed . |
| 68 | Supply and fix 200 mm long aluminum anodised barrel tower bolts of extruded section complete all as specified and directed. |
| 69 | S&F as in repairs 25 mm dia and 1mm thick MS chromium plated curtain rods with fixing side fancy type brackets end knobs fixed with steel screws etc all as specified and directed . |
| 70 | Supply and fix, as in repair, vitreous china wash basin, white flat back size 550mm X 400mm, excluding taps, waste chain, plug and porcelain stopper but including waste coupling, brackets, cutting for and pinning in ends of bracket or erecting stand complete all as specified. |
| 71 | S&F in repair for single piece vitreous china wash down water closet pan of pedestal pattern, white, with P or S trap including plastic water closet seat cover, white, close pattern with flat bottom, and cover and mild steel chromium plated or aluminised hinging device, jointed in white cement, complete all as specified and directed.Make: Hindware Cat Part No. 20125 with Cistern fittings or equivalent make as approved list of make. |
| 72 | S & F soap dish chromium plated standerd quality fixed on wall with brass screw complete all as specified. |
| 73 | S & F PVC connections 15mm dia size with PTMT nuts of length 450mm complete in all respect as specified |
| 74 | S & F 15mm bore pillar tap cast copper alloy with capstan head, chromium plated concealed screwed down high pressure with or without hot or cold with long shunk screwed shanks and fly nuts screwed for iron pipes and connecting to water pipe line complete all specified and directed. |
| 75 | Supply and fix as 15 mm bore bib taps fancy type, chromium plated, cast copper alloy with crutch or butter fly handle, screwed down, screwed for iron pipe or for brass ferrule complete all specified and directed. |
| 76 | Supply and fix 15mm bore stop valve/angle valve, cast copper alloy cromium plated fancy type screwed down high pressure, with crutch or butterfly handle for 15 mm bore pipe or for unions complete all specified and directed. |
| 77 | Supply and fix 15mm bore angular stop cock of cast copper alloy, screwed down, high pressure screwd chromium plated and fixed complete all as specified. |
| 78 | S&F in repairs Health faucet (ABS Body) mild steel chromium plated suitable for 15 mm dia pipe with 1.25 metre long flexible tube and ABS wall hook including making connections and fixed in position complete in all respect as specified |
| 79 | S & F 600mm X 450mm bevelled edge mirror of selected quality glass, mounted on 6mm thick AC building board or commercial plywood and fixed to wooden plugs with chromium plated brass screws and cup washers complete all as specified and directed. |
| 80 | Supply and fix in repair Towel ring fixed with CP brass screw and wooden/plastic cleat complete all as specified. |
| 81 | Supply and fix in repair Towel rail, 20mm dia brass chromium plated, 600mm long with fancy type brass chromium plated brackets on both sides and fixed with steel screws and wooden/rawl plugs complete all as specified. |
| 82 | Supply and fix 125mm dia CP brass shower rose with swivel joints, any colour including shower arm 15mm dia, 195mm long with bend of 45 degree with flange of CP brass complete all as specified.Make : Parryware cat No. T9809A1 or equivalent as per approved list of make. |
| 83 | Supply and fix 160mm bore PVC (SWR) pipes single socketed with rubber joint, in any length, laid in trenches or in floors / fixed to walls complete all as specified. |
| 84 | Supply and fix 110mm bore PVC (SWR) pipes single socketed with rubber joint, in any length, laid in trenches or in floors / fixed to walls complete all as specified. |
| 85 | Supply and fix 75mm bore PVC (SWR) pipes single socketed with rubber joint, in any length fixed to walls / floors or in trenches complete all as specified. |
| 86 | Supply and fix 160mm bore PVC (SWR) bend suitable for pipe complete all as specified. |
| 87 | Supply and fix 110mm bore PVC (SWR) bend suitable for pipe complete all as specified. |
| 88 | Supply & Fixed 75mm bore PVC (SWR) bends suitable for pipe complete all as specified. |
| 89 | Supply and fix 160mm bore PVC (SWR) junction, single T equal or unequal with or without door access complete all as specified. |
| 90 | M & L PVC(SWR) floor trap, 75mm dia outlet, plain with grating including jointing with solvent cement complete all as specified. |
| 91 | Supply & Fixed 150mm square size Grating PTMT (minium wt 100 gms) complete all as specified. |
| 92 | S&F 15mm bore steel water tubing, medium grade, galvanised with screwed and socketed joints, in any length, including supply and fixing all fittings, ISI marked conforming to IS -1239 and fixed to walls or laid in floors / trenches required for water connections complete all as specified and as directed. |
| 93 | S&F 20mm bore steel water tubing, medium grade, galvanised with screwed and socketed joints, in any length, including supply and fixing all fittings, ISI marked conforming to IS -1239 and fixed to walls or laid in floors / trenches required for water connections complete all as specified and as directed. |
| 94 | S&F Solid PVC Wall Lining consisting of 5mm thick wood grain printed PVC sheet inclusive of solvent cement and fixing at site on PVC frame complete all as specified and directed. |
| 95 | S & F 5mm thick PVC sheet fillet of width 35mm for wall paneling, inclusive of fixing on to wall to make PVC frame complete all as specified and directed. |
| 96 | Providing & fixing false ceiling with semi perforated 12 mm thick micro tegular edged or 10 mm thick square edge at all heights with GRG (Glass Fiber Reinforced Gypsum) false ceiling tiles of size 595 × 595 mm of approved texture design and pattern having moisture content less than 2%, humidity resistance of 99%, NCR 0.50 to 0.75 as per IS 8225 : 1987, non-combustible as per BS 475 (Part-IV) 1970 and light code description Unit Rate No. 429, Sub Head 26.0 – New Technologies and Material, reflectance of 85% minimum, laid in true horizontal level, suspended on interlocking metal T-grid of hot dipped galvanized iron section of 0.33 mm thick (galvanized @ 120 gms/sqm including both sides) comprising of:Main T runner of size 15 × 32 mm, length 3000 mm.Cross T of size 15 × 32 mm, length 1200 mm.Secondary intermediate cross T of size 15 × 32 mm, length 600 mm.To form grid module of size 600 × 600 mm, suspended from ceiling using galvanized metal sheet item (galvanized @ 80 gms/sqm), i.e. 50 mm long, 8 mm outer diameter M-6 fasteners, 6 mm dia fully threaded hanger rod up to 1000 mm length, and L-shape level adjusters of size 85 × 25 mm, galvanized iron perimeter wall angle of size 24 × 24 × 0.40 mm, length 3000 mm, to be fixed on perimeter of wall/partition with the help of plastic rawl plugs at 450 mm centre to centre and 40 mm long drywall screws.The work shall be carried out as per specification, drawing and as per direction of Engr-in-Charge |
| 97 | M & L for preparation of new surface and applying wall care putty in two coats of 1.0mm thickness over plastered surface to prepare the surface even and smooth complete all as specified. |
| 98 | M & L preparation of new plastered surface of walls and applying two coat of oil emulsion distemper over one coat of primer with using roller complete all as specified. |
| 99 | Material & Labour for preparation of new plastered surface applying two or more coats of 100% Premium acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives @ 1.43 litre/ 10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/ 10 sqm using roller complete all as specified and directed. |
| 100 | M & L preparation of new steel surfaces of any description over 10cm width or girth not otherwise described and applying two coats of synthetic enamel paint over one coat of red oxide primer complete all as specified and as directed. |
| 101 | Supplying and planting of Ashoka tree/ Gulmohar/ Sheesam/ Neem of height 0.9 to 1.2 metre staking with bamboo sticks in a pit of size 60cm x 60cm trench by excavating hole in ordinary soft/ loose soil in 90 cm in depth getting out, returning filling after plantation in the same with excavated earth mixed with manure fertilizer NPK (12:32:16) @ 100 gm/ Plant and insecticide phoate @ 50 gm/ plant including removal and stacking of serviceable material and then depositing of surplus soil by spreading and neatly leveling within a lead of 50 meter and making up the trenches area to proper level complete including maintenance and protection of plant during currency of contract (Phase-I) all as specified and directed by Engineer-in-Charge. |
| 102 | Supplying and planting of bottle Palm plant tree of height 0.9 to 1.2 metre staking with bamboo sticks in a pit of size 60cm x 60cm trench by excavating hole in ordinary soft/ loose soil in 90 cm in depth getting out, returning filling after plantation in the same with excavated earth mixed with manure fertilizer NPK (12:32:16) @ 100 gm/ Plant and insecticide phoate @ 50 gm/ plant including removal and stacking of serviceable material and then depositing of surplus soil by spreading and neatly leveling within a lead of 50 meter and making up the trenches area to proper level complete including maintenance and protection of plant during currency of contract (Phase-I) all as specified and directed by Engineer-in-Charge. |
| 103 | Supplying and planting of Kinno, Orange & Nimbu plant of height 0.9 to 1.20metre staking with bamboo sticks in a pit of size 60cm x 60cm trench by excavating hole in ordinary soft/ loose soil in 90 cm in depth getting out, returning filling after plantation in the same with excavated earth mixed with manure fertilizer NPK (12:32:16) @ 100 gm/ Plant and insecticide phoate @ 50 gm/ plant including removal and stacking of serviceable material and then depositing of surplus soil by spreading and neatly leveling within a lead of 50 meter and making up the trenches area to proper level complete including maintenance and protection of plant during currency of contract (Phase-I) all as specified and directed by Engineer-in-Charge. |
| 104 | Supplying and plantation of grass turfing by digging of earth upto 15cm deep and planting of grass 5 cm apart, formation of turf within 3 months leveling of digging earth after mixing of manuare fertilizer NPK (12:32:16) @ 100/ Sqm, insecticide phorate @ 100 gm/ sqm and vermicompost @ 1.0 Kg/ Sqm with the earth. The gypsum is to mixed with the earth @5 Kg/ Sqm if the soil is sodic. |
| 105 | Complete maintenance & protection of tree/ plant including watering, training, weeding, pruning, hoeing, insect-pest management (as and when required) month replacement of plants (as and when required), gap filling, making of 'Thaola', cleaning of nearby area and enrichment with and including manure (cow dung/ meegni) @ 0.003 cum per pit complete all as specified and directed by Engineer-in-charge |
| 106 | Complete maintenance & protection of Grass/plant including watering, training, weeding, pruning, hoeing, insect-pest management (as and when required) month replacement of plants (as and when required), gap filling, making of 'Thaola', cleaning of nearby area and enrichment with and including manure (cow dung/ meegni) @ 0.003 cum per pit complete all as specified and directed by Engineer-in-charge |
| 107 | E & M Division items |
| 108 | Taking down carefully copper/aluminium point wiring (light, fan, buzzer, socket or power) complete including fixture and fittings such as switches, ceiling roses, pendants, regulators, sockets, light fitting etc including removing from site for taking credit and making good to disturbed surface of walls, floors etc as per existing specification complete all as specified and as directed. |
| 109 | Taking down carefully submain wiring including all accessories without disturbing existing wiring fittings fixtures etc and making good to the disturbed surfaces all as directed and as specified in any type and size all as directed. |
| 110 | Dismantling old unserviceable main switches, sheet metal enclosures DB including MCBs etc and removing from site for taking credit incl making good to disturbed surface of wall as per existing specification complete all as specified and as directed. |
| 111 | M & L for point wiring with FRLSH stranded copper conductor 1.5 sqmm (nominal area), two single core, PVC insulated cable 1100 volts grade, ISI-694 marked in and including heavy duty,concealed PVC Conduit including all accessories etc ISI marked, with GI sunken box suitable for fixing switches, sockets and regulators including PVC insulated stranded copper conductor 1.5 sqmm (nominal area) single core cable as earth continuity conductor to common earth and connecting to earth dolly complete all as specified and directed for One light point controlled by one switch. |
| 112 | M & L for point wiring with FRLSH stranded copper conductor 1.5 sqmm (nominal area), two single core, PVC insulated cable 1100 volts grade, ISI-694 marked in and including heavy duty, concealed PVC Conduit including all accessories etc ISI marked, with GI sunken box suitable for fixing switches, sockets and regulators including PVC insulated stranded copper conductor 1.5 sqmm (nominal area) single core cable as earth continuity conductor to common earth and connecting to earth dolly complete all as specified and directed for One fan point/exhaust fan point controlled by one, one way switch 5 Amp. |
| 113 | M & L for point wiring with FRLSH stranded copper conductor 1.5 sqmm (nominal area), two single core, PVC insulated cable 1100 volts grade, ISI-694 marked in and including heavy duty, concealed PVC Conduit including all accessories etc ISI marked, with GI sunken box suitable for fixing switches, sockets and regulators including PVC insulated stranded copper conductor 1.5 sqmm (nominal area) single core cable as earth continuity conductor to common earth and connecting to earth dolly complete all as specified and directed for One 3 pin 5 Amp socket outlet point controlled by one switch on the same board. |
| 114 | M & L for point wiring with FRLSH stranded copper conductor 1.5 sqmm (nominal area), two single core, PVC insulated cable 1100 volts grade, ISI-694 marked in and including heavy duty, PVC Conduit including all accessories etc ISI marked, with GI sunken box suitable for fixing switches, sockets and regulators including PVC insulated stranded copper conductor 1.5 sqmm (nominal area) single core cable as earth continuity conductor to common earth and connecting to earth dolly complete all as specified and directed for One 3 pin 5 Amp socket outlet point controlled by one switch on independent board. |
| 115 | M & L for point wiring with FRLSH stranded copper conductor 2.5 sqmm (nominal area), two single core, PVC insulated cable 1100 volts grade, ISI-694 marked in and including heavy duty, PVC Conduit including all accessories etc ISI marked, with GI sunken box suitable for fixing switches, sockets and regulators including PVC insulated stranded copper conductor 2.5 sqmm (nominal area) single core cable as earth continuity conductor to common earth and connecting to earth dolly complete all as specified and directed for 3 pin, 15 Amp socket outlet, independent |
| 116 | S&F switch piano flush type button single pole one way 5 Amps all as specified and directed. |
| 117 | S&F socket outlet 2 in 1, 3 pin 5 Amp flush type all as specified and directed. |
| 118 | S&F switch socket combination 5 in 1 5/16 Amp flush type with all as specified and directed. |
| 119 | S&F ceiling rose surface bakelite with three terminals all as specified and directed |
| 120 | S&F lamp angular holder insulated body with back plate complete all as specified. |
| 121 | M & L for submain wiring with two single core 6.0 sqmm PVC insulated unsheathed cable multi-strand copper conductor FRLSH drawn through and including PVC non metallic rigid Conduit conceled with all fittings and fixing accessories on roof, walls, ceiling etc including 1 x 4.0 sqmm PVC insulated unsheathed multi strand copper conductor earth wire FRLSH connecting earth including cutting groove for concealed wiring, making good to disturb surface of wall/floor with cement mortar and finishes to match existing complete all as specified and directed. Note: Two run of single core cable, one run earth wire and one run PVC Conduit will be measured as one length. |
| 122 | Supply & Fix LED betten plastic type fitting of capacity 20W, wall mounted, operating on 230V, 50Hz, AC Supply having luminous efficiancy not less than 125 lumens/watts, CCT 6500K, P.F>0.9, 2.5 KV surge protection, 4-feet long with decorative end caps elegently designed complete all as specified. Make : Cat Part No LDLL20-WW of crompton or equivalent of make |
| 123 | Supply and fixing LED luminaire 600 mm x 600 mm, 35/36 watt, 220 V AC recessed type down lighter with high efficiency PMMA diffuser soft glare free light complete with driver, holders & LED lamp suitable for roof ceiling including connecting up with driver three core flexible copper conductor cases of suitable size complete all as specified and directed. |
| 124 | Supply & Fix 25 watt enviromental friendly bldg security street light, LED luminaire made up of pressure die cast alluminium body with mid power LED as lighting sources and PC cover having Top opening separate driver compartment with IP66 protection and impact resistance of IK07 including fixing arrangements and taking down old rusted bracket fittings complete all as per directed by Engr-in–charge. |
| 125 | S&F plastic body exhaust fan 250mm sweep complete with louvers shutter, voltage 230V, 50 Hz, RPM 1200, copper winding and connecting to ceiling rose with flexible copper cable including making holes on the wall and making good to the disturbed surfaces complete all as specified and as directed. |
| 126 | S&F BLDC ceiling fan 1200mm sweep complete with blades, down rods and accessories, 230 V, min air delivery 210 CFM with service value 6.00 BEE 5 star rated & provn of ‘S’ type fan hook including taking down of old UNSV one and depositing to MES storeyard for keeping in safe custody complete all as specified and directed. |
| 127 | S&F metal plug socket with MCB SP 20 Amp, 240 V enclosure for AC/equipment with neutral and earth point complete all as specified and directed. |
| 128 | S&F sheet metal enclosure powder coated three phase and neutral (TPN) DB for fixing of MCBs, 4 way double door with aluminum bus bar 100 Amp including grouting on the wall by means of screws and rawal plugs and making good disturbed surfaces complete all as specified and directed. |
| 129 | S&F sheet metal enclosure powder coated single phase DB for fixing of MCBs, 8 way double door with Aluminum bus bar 100 Amp including grouting on the wall by means of screws and rawal plugs and making good disturbed surfaces complete all as specified and directed. |
| 130 | S&F MCB TPN of capacity 63 Amps, 240 V, 10 KA 'B' curve complete all as specified and directed. |
| 131 | S&F MCB SPN of capacity 40-63 Amps, 240 V, 10 KA 'C' curve complete all as specified and directed. |
| 132 | S&F MCB SP of capacity 5-32 Amps, 240 V, 10 KA 'C' curve complete all as specified and directed. |
| 133 | Taking out old existing earthing and M & L for new earthing with galvanised steel earth plate electrode 600mm X 600mm X 6mm thick burried directly in ground (earth pit not less than 2.25 mtr below ground level) with top edge of the plate not less than 1.5 mtr below ground level connected to 4mm dia GI wire protected by 20 mm bore light grade galvanised iron pipe and other end connected to test point as directed including funnel with wire mesh and watering pipe 20 mm bore medium grade galvanised iron pipe with charcoal and common salt in alternaterlayers of 15 cm thickness all around the GI plate electrode with concrete pit in PCC 1:3:6 type C-1 with cast iron frame including cast iron cover 10mm thick hinged to CI frame and 6mm MS rod for handle, necessary excavation and earth wok in hard/dense soil and disposal of spoil to a distance n exc 50 m and necessary testing complete all as shown in electrical plate No 3 of SSR part-I complete all as specified and directed. Please Enable Macros to View BoQ information |
AI Tender Summary
Tender Timeline
Jul 14, 2026
11:30 IST
Tender Published
Tender notice published.
CompletedAug 05, 2026
17:00 IST
Bid Submission Deadline
Online submission via eProcurement portal.
Upcoming · 8 daysAug 08, 2026
Bid Opening Date
Technical bids will be opened and evaluated.
Upcoming · 11 daysTender Documents
Download All (ZIP) ↓
Disclaimer
We takes all possible care for accurate & authentic tender information. However users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender