Tender For Improvement Of Water Distribution Network At Gobardhana Block Id-1241 Ac-127390605 Under 15Th Fc Tied Grant For The Year 2024-25 During 2025-26.
Tender Value
1 Crore
Estimated cost
Bid Submission
04 Aug 2026
5 days left
EMD
2 Lakhs
Bank guarantee accepted
Document Fee
2000
Non-refundable
Tender Type
Online
Tender Overview
Organization
Tender ID
Competition Type
NCB
Bidding Type
Tender
Location / State
Barpeta → Assam
EMD Exemption
Available
Quantity
Not Available
Website
Contact Person
Address
Project Description
Tender for Improvement Of Water Distribution Network At Gobardhana Block Id-1241 Ac-127390605 Under 15Th Fc Tied Grant For The Year 2024-25 During 2025-26.
BOQ
| Sl. No. | Item Description |
| 1 | Supplying, laying , fitting & fixing HDPE pipes ( High Density poly ethylene pipes pE 100 ) conforming to IS 4984/2016 (with up to date amendament) with necessary jointing material like mechanical connector of jointing pipes by heating the ends of pipes with help of teflon coated electric mirror / heater to the required temperature and then pressing the ends together against each other to form a monolitic and leak proof joint by thermosetting process. it may be required to be done with jack/ hydraulc jacks/butt fusion machine . (50mm & above fusion jointed & below 50mm mechanical jointed). the HDPE fitting should be ISI marked conforming to relevant BIS code. i) 63mm dia |
| 2 | ii) 75mm dia |
| 3 | iii) 90mm dia |
| 4 | iv) 110mm dia |
| 5 | v) 125mm dia |
| 6 | Constructing of Brick masonry Sluice Valve Chamber 900mm(L) x 900mm(B) x 1250mm(H) inside, in 230mm brick work in cement mortar 1:5 (1 cement : 5 coarse sand) and precast R.C.C cover slab in prop. 1:2:4 mix (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size ) reinforced with 10mm M.S. bar @ 150mm centre both ways tying with 20 gauge black annealed wire including necessary earthwork (excavation and return filling), 75mm PCC in prop. 1:4:8 (1 cement:4 coarse sand : 8 coarse agg.) over brick flat soling and 15 mm thick inside plastering and outside plastering (upto 150mm from top) with cement mortar 1:5 (1 cement : 5 coarse sand) , complete as per standard design, including Supplying, carrying, placing in position, fitting and fixing 100mm/ 125mm/ 150mm diameter CID/F sluice valve all complete as directed. Approved good for construction drawing will be issued by the deptt. A) For 100mm dia Sluice valve against 110mm dia Distribution pipe line - 1 no. 100mm dia CID/F sluice valve with cap/ wheel as per IS 14846-2000 PN 1.0 with ISI marking, 2 nos. 100mm dia GI Nipple (225mm long), 4 Nos. 100mm dia GI Threaded Flange, 2 Nos. 110mm dia UPVC Flange, 28 Nos. Bolts & nuts and 6 nos. 3mm thick rubber insertion sheet for 100mm dia pipe. |
| 7 | B) For 125mm dia Sluice valve against 140mm dia Distribution pipe line - 1 no. 125mm dia CID/F sluice valve with cap/ wheel as per IS 14846-2000 PN 1.0 with ISI marking, 2 nos. 125mm dia GI Nipple (225mm long), 4 Nos. 125mm dia GI Threaded Flange, 2 Nos. 140mm dia UPVC Flange, 30 Nos. Bolts & nuts and 6 nos. 3mm thick rubber insertion sheet for 125mm dia pipe. |
| 8 | Construction of Functional Household Tap Connection including earthwork in excavation for pipe line (both for connection in distribution line and service connection) and refilling, dressing etc., providing PVC Saddle Piece of average size 110 mm x 15 mm (i.e. ranging from 63mm to 140mm) and make Supreme or equivalent, making holes in the distribution pipe, providing 15 mm dia bronze ferrule cock (PN-16) conforming to IS:2692 (1989) as ammended and make Zoloto or equivalent, connecting it to the saddle piece, providing and fixing 3 layer (Outer green / GREY coloured UV Stabilised, middle black coloured UV Stabilised and inermost layer white coloured with antimicrobial property) Fusion welded PP- R ( Poly propylene-random copolymer) Pipes, SDR 7.4 having thermal stability for hot and cold water supply conforming IS 15801-2008 of length 10m from saddle piece to the tap point ( pipes of make SFMC/ FUSION/Wetflow, Kisan brand or other brand of equivalent quality and PN-16 Pipe,20 mm OD,SDR-7.4) including all plain PP-R fittings and brass threaded PP-R fitting and clamping, cutting and making good to the damages, including all taxes and duties as applicable and including the cost of all required labour and materials as directed and specified. The item also includes construction and installation of R.C.C Hydrant Pillar of size 100mm x 100 mm , height 1200 mm with 6 mm dia bar embeded to RCC Post in proportion 1:1.5:3 with 4 nos 10 mm dia main and 6 mm dia stirrup @ 150 C/c and fixing 15 mm dia PPR pipe to the hydrant, with 6 mm rings embedded in concrete for anchoring inclusive of cost of transportation to site and also supplying fitting and fixing PVC Bib cock all complete as directed and specified. Approved good for construction drawing |
| 9 | Odex : Providing installation and commissioning of 150x150 mm dia DTW by Odex boring within the jurisdiction of different PHE divisions including including preparation of site for placing of drilling rig, air compressor, transportation of rig and ancillary equipments. Construction of temporary accommodation and low cost sanitary facility for drilling staff and providing water supply facilities at drilling site. Drilling of bore well by using drilling rig having ODEX system Extraction of drilling pipes / bits against skin friction at the end of each day and after completion of the operation including washing of the bore hole all complete as directed and lowering / sinking of well assembly including welding of pipe joints. Developing of the D.T.W. with air compressor, Make- Kirloskar / Cumins all complete as directed by the department. |
| 10 | Supplying, installation, testing, commissioning of water lubricated submersible pump set 3-phase (3HP/5HP/7.5HP/10/HP)/Ingle Phase (1HP/2HP) pump with bronze impeller of suitable diameter all complete. The pump set should be coupled with wet type submerssible electric motor drive of adequate power suitable for operation at 230V/415V, 50 Hz input power including sockets, bends, elbows etc. clips, electrical switch gear (Starter) etc. electric controol panel board made of MS sheet duly painted with anti-corrosive paints complete fitted with all electrical accessories, i.e. off-on switch, voltemeter, ameter, indicator light etc bright annealed electrolytic bar copper conducted PVC insulated sheather around flexible 3-core cable of the motor manufactured conforming to IS:694/1990 all complete as specified & directed by the Deptt with one year warranty from the date of commissioning & satisfactory testing against any manufacturing defect (If any such defect is found during the year from the date installation and satisfactrry testing, supplier will have to rectify the defect at their cost & risk & if necessary replace the pump set) Test certificate of pump, motor, starter, panel board etc from the manufacturer shall have to be submitted). 3-Ph 5.0HP head considering all losses: 55m. |
| 11 | Construction of Brick boundary wall including necessary earthwork in excavation for foundation trenches of walls, footing of columns including refilling (return filling) the quantity as necessary after completion of work, breaking clods in return filling, dressing, watering and ramming etc. and removal of surplus earth, 100 mm thick PCC in proportion 1:3:6 over flat brick soling, with brickwork in cement mortar in proportion 1:4 with 230mm thick first class brick in sub-structure upto plinth level and 112 mm thick above plinth upto height of 1.5 m, and providing RCC pillar of 0.20mx0.20mx 1.50 meter height above GL at 3.0 meters apart and for gate 2 nos. posts of size 0.30mx0.30mx 1.60 meter above ground level, tie beam of 0.20mx0.25m cross section, 6 nos. 12mm dia main bar for each gate post and 4 nos for each boundary colums and stirrups @ 150mm c/c and plastering in proportion 1:4, and colour washing with lime of approved brand incuding form work, shuttering and shoring all complete as per approved good for construction drawing as directed and specified by the by the deptt. Nimua PWSS. |
| 12 | Supplying, fitting and fixing double leaf heavy duty iron gate, frame made from 50mm x 6mm M.S. flat iron with another horizontal flat at the middle, 20mm dia M.S bars at 200mm apart from bottom flat to top flat and 20 mm dia M.S. bars at 200mm apart from bottom flat to middle flat including drilling, welding etc. complete. All vertical bars are to be protruded at least 100mm above the middle and top flat is to be flattended and pointed as directed. Necessary locking arrangement on both faces, arrangement for temporary closing the gate and 2 nos.( minimum) strong iron hinges of M.S bars and flat of same sizes on each leaf to be embeded in C.C brick pillars as necessary including a red oxide painting to all iron works as directed and specified. (Separate payment will be made for posts). Nimua PWSS. Please Enable Macros to View BoQ information |
AI Tender Summary
Tender Timeline
Jul 14, 2026
11:30 IST
Tender Published
Tender notice published.
CompletedAug 04, 2026
17:00 IST
Bid Submission Deadline
Online submission via eProcurement portal.
Upcoming · 5 daysAug 05, 2026
Bid Opening Date
Technical bids will be opened and evaluated.
Upcoming · 6 daysTender Documents
Download All (ZIP) ↓
Disclaimer
We takes all possible care for accurate & authentic tender information. However users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender