Tender For Improvement Of Water Distribution Network At Tamulpur Block Id-1018 Ac-126153617 Under 15Th Fc Tied Grant For The Year 2024-25 During 2025-26.
Tender Value
1.28 Crore
Estimated cost
Bid Submission
04 Aug 2026
6 days left
EMD
2.57 Lakhs
Bank guarantee accepted
Document Fee
2579
Non-refundable
Tender Type
Online
Tender Overview
Organization
Tender ID
Competition Type
NCB
Bidding Type
Tender
Location / State
Baksa → Assam
EMD Exemption
Available
Quantity
Not Available
Website
Contact Person
Address
Project Description
Tender for Improvement Of Water Distribution Network At Tamulpur Block Id-1018 Ac-126153617 Under 15Th Fc Tied Grant For The Year 2024-25 During 2025-26.
BOQ
| Sl. No. | Item Description |
| 1 | Odex : Providing installation and commissioning of 150x150 mm dia DTW by Odex boring within the jurisdiction of different PHE divisions including including preparation of site for placing of drilling rig, air compressor, transportation of rig and ancillary equipments. Construction of temporary accommodation and low cost sanitary facility for drilling staff and providing water supply facilities at drilling site. Drilling of bore well by using drilling rig having ODEX system Extraction of drilling pipes / bits against skin friction at the end of each day and after completion of the operation including washing of the bore hole all complete as directed and lowering / sinking of well assembly including welding of pipe joints. Developing of the D.T.W. with air compressor, Make- Kirloskar / Cumins all complete as directed by the department. i) Habibari Bathou Mandir |
| 2 | ii) Dipti Bathou Mandir |
| 3 | iii) Kalbari Bathou Mandir |
| 4 | iv) Modaigami Bathou Mandir |
| 5 | v) Gerua Jame Majid |
| 6 | Supplying, installation, testing and commissioning of Raw water submerssible pump set of different capacity at various PWSS under different divisions of the state. Supplying, installation, testing and commissioning of water lubricated Submersible Pump Set 3-Phase (for 5HP/ 7.5HP) / Single phase (for 1 HP / 2HP / 3 HP) pump with bronze impeller of suitable diameter all complete. The pump set should be coupled with wet type submersible electric motor drive of adequate power suitable for operation at 230V/ 415 V, 50 Hz input power including supply of steel cable rope, G.I. column pipe, suction strainer, Sluice Valve, Non-Return valve, sockets, bends, elbows etc. & GI delivery piping above ground up to sluice valve above ground level, electrical cable of adequate cross section, clips electrical switch gear (starter) etc., Electric Control Panel Board made of MS Sheet duly painted with Anti-corrosive paints complete fitted with all electrical accessories i.e. Off On Switch, Voltmeter, Ameter, Indicator light etc., bright Annealed Electrolytic Bar Copper Conducted PVC insulated sheathed round flexible 3-core Cable of the Motor Manufactured conforming to IS:694/1990 all complete as specified and directed by the Department with One year warranty from the date of commissioning and satisfactory testing against any manufacturing defect. [If any such defect is found during the year from the date of installation and satisfactory testing, supplier will have to rectify the defect at their cost and risk & if necessary replace the pump set. i) Discharge of the pump - 22.7 LPM, Design Head - 56 M, Recommended make:- Crompton Greaves/ Aquatic/ CRI/ GEC/ ALSTHOM/ V- Guard or equivalent. i) Habibari Bathou Mandir. |
| 7 | ii) Dipti Bathou Mandir |
| 8 | iii) Kalbari Bathou Mandir |
| 9 | iv) Modaigami Bathou Mandir |
| 10 | v) Gerua Jame Majid |
| 11 | Construction of RCC overhead reservoir with sintex (capacity with 2x5000 liters) 12M staging including rapid sand filter and UGR. i) Habibari Bathou Mandir. |
| 12 | ii) Dipti Bathou Mandir |
| 13 | iii) Kalbari Bathou Mandir |
| 14 | iv) Modaigami Bathou Mandir |
| 15 | v) Gerua Jame Majid |
| 16 | Supplying, laying , fitting & fixing GI (Medium Class) Pipe conforming to IS- 1239 (pt-I) 2004 (Ammended 2010) including GI specials and jointing material, cutting of pipe materials and necessary earthwork in trenching and refilling of earth and restore to its original condition including dressing, dewatering incuding bailing out water where necessary all complete and also necessary testings and commissioning as per direction of the department. i) Habibari Bathou Mandir. |
| 17 | ii) Dipti Bathou Mandir |
| 18 | iii) Kalbari Bathou Mandir |
| 19 | iv) Modaigami Bathou Mandir |
| 20 | v) Gerua Jame Majid |
| 21 | Supplying, installation, testing and commissioning of Centrifugal pump set of different capacity at various PWSS under different divisions of the state Supplying, installation, fitting & fixing, testing and commissioning of Electric driven 3-phase (for 5HP/ .5HP/10HP/12.5HP) / Single phase (for 1 HP / 2HP/ 3 HP pump) Centrifugal pump set of approved make with bronze impeller of suitable diameter with G.I. suction pipe, suction strainer, non-return valve, delivery piping up to sluice valve all complete. The pump set should be coupled with electric motor drive of adequate power suitable for operation at 230V / 415 V, 50 Hz input power with DOL Starter /Star delta Starter including Electric Control panel board enclosure made of MS Sheet duly painted with Anti-corrosive paints complete, fitted with all electrical accessories Discharge of the pump - 26 LPM2 HP -Centrifugal type Pumpset. i) Habibari Bathou Mandir. |
| 22 | ii) Dipti Bathou Mandir |
| 23 | iii) Kalbari Bathou Mandir |
| 24 | iv) Modaigami Bathou Mandir |
| 25 | v) Gerua Jame Majid |
| 26 | Supplying, laying , fitting & fixing HDPE pipes ( High Density poly ethylene pipes pE 100 ) conforming to IS 4984/2016 (with up to date amendament) with necessary jointing material like mechanical connector of jointing pipes by heating the ends of pipes with help of teflon coated electric mirror / heater to the required temperature and then pressing the ends together against each other to form a monolitic and leak proof joint by thermosetting process. it may be required to be done with jack/ hydraulc jacks/butt fusion machine . (50mm & above fusion jointed & below 50mm mechanical jointed). the HDPE fitting should be ISI marked conforming to relevant BIS code. 90mm dia HDPE i) Habibari Bathou Mandir. |
| 27 | ii) Dipti Bathou Mandir |
| 28 | iii) Kalbari Bathou Mandir |
| 29 | iv) Modaigami Bathou Mandir |
| 30 | v) Gerua Jame Majid |
| 31 | Construction of Functional Household Tap Connection including earthwork in excavation for pipe line (both for connection in distribution line and service connection) and refilling, dressing etc. Providing tegrated Saddle piece with flow control valves (SS- FCV and fasteners) of size 90 MM X 15 MM outlet (I.e. ranging from 63mm to 160mm) making holes in the distribution pipe, Flow control valve of SS31G (integraled with saddle piece) with flow of 3 - 5 LPM at standard operating pressure of 0.5 bar to 1.5 bar, connecting it to the saddle piece, providing and iixing 3 layer (Outer green / GREY coloured UV Stabilised, middle black coloured UV Slabilised and inermost layer white coloured with antimicrobial property) Fusion welded PP-R (Poly propylene-random copolymer) Pipes, SDR 7.4 having thermal slabilily for hot and cold water supply conforming IS 15801-2008 of average lenglh 10 m from saddle piece lo the standpost ( pipes ol make empanelled manufacturers and PN- 16 Pipe,20 mm OD,SDR-7.4) including all plain PP-R fitfings and brass threaded PP-R fitting and clamping, cutting and making good to the damages, including all taxes and duties as applicable and including the cost of all required labour and materials as directed and specified. The item also inludes construction and installation of Cement Concrète Hydrant Pillar with cement concrète in proposrtion 1:3:6 sheathed in SWR pipe of dia 110mm height 1200 mm encasing 15 mm dia PPR pipe inside the hydrant, inclusive of cost of transportation to site and also supplying fitting and fixing C.P. Brass Bib cock conforming to IS:8931 all complexe as directed and specified. Approved good for construction drawing will be issued by the deptt. i) Habibari Bathou Mandir. |
| 32 | ii) Dipti Bathou Mandir |
| 33 | iii) Kalbari Bathou Mandir |
| 34 | iv) Modaigami Bathou Mandir |
| 35 | v) Gerua Jame Majid |
| 36 | External & Internal Electrification to Raw & Clear water pump house including wiring for light/fan/call bell point with 2x1.5 sq mm PVC insulated single core unshearthed industrial cable FB confiriming to Is-694 : 1990 with flexible bright annelead eletrolytic copper conducter for voltage grade up to 1100 volts(finolex/RR kabel/ Nicco/ Anchor or Equivalent make as approved by deptt) providing and fixin ICSP and N link main switch of 240 volts grade including drilling boards/ iron frames and fixing with bolts and nuts and connection as approved by the dept. complete as required , providing and fixing LC distribution fuse boards with rewire able fuses 250 volt grade, supplying fixing of 18/20 - 5/9 watt CFL lamp in the existing batten holder/angle holder/decorative /bulk head fitting / pendent holder etc as specified and directed by the deptt. i) Habibari Bathou Mandir. |
| 37 | ii) Dipti Bathou Mandir |
| 38 | iii) Kalbari Bathou Mandir |
| 39 | iv) Modaigami Bathou Mandir |
| 40 | v) Gerua Jame Majid |
| 41 | Supply, installation, testing and comissioning of electrically operated chemical dosing pump of 6 L capacity and 6 kg/cm2 complete with PVC solution mixing container and electrical wiring with panel board fitting and fixing at site with suction and discharge tubings.Standard Materials for construction1. Housing :- Fiber reinforced plastic2. Spacer & Head :- Poly propylene/UPVC3. Diapharm :- Tefflon Faced Hupalon4. Ball :- PTFE5. Suction & discharge ball cartidge :- Poly propylene/UPV6. Suction & Discharge Tubings :- HDPE/LDPE7. MS Fabricated stand for mixing container. i) Habibari Bathou Mandir. |
| 42 | ii) Dipti Bathou Mandir |
| 43 | iii) Kalbari Bathou Mandir |
| 44 | iv) Modaigami Bathou Mandir |
| 45 | v) Gerua Jame Majid |
| 46 | Supplying, laying , fitting & fixing HDPE pipes (High Density poly ethylene pipes pE 100 ) conforming to IS 4984/2016 (with up to date amendament) with necessary jointing material like mechanical connector of jointing pipes by heating the ends of pipes with help of teflon coated electric mirror / heater to the required temperature and then pressing the ends together against each other to form a monolitic and leak proof joint by thermosetting process. it may be required to be done with jack/ hydraulc jacks/butt fusion machine . (50mm & above fusion jointed & below 50mm mechanical jointed). the HDPE fitting should be ISI marked conforming to relevant BIS code. i) 63mm dia. |
| 47 | ii) 75mm dia. |
| 48 | iii) 90mm dia. |
| 49 | iv) 110mm dia. |
| 50 | Construction of gravity type Rapid Sand Filter of Size 4m2/6m2 including the following item of works: (i) Earthwork for excavation (ii) 150 mm thick PCC (prop. 1:3:6) (iii) Brick soling (iv) Formwork of ordinary timber planking including centering, shuttering, propping, etc. (v) PCC/RCC works (M25 grade in foundation & superstructure) (v) 250 mm brick work in cement morter with 1st class brick including racking out joints and dewatering if necessary, and curing complete as directed. (vi) 15 mm thick Cement plaster in single coat on rough and fair side (prop. 1:4) (vii) Finishing old / new wall with water proofing weather coat smooth anti-fungal exterior painting of approved make (two coats) (viii) Supplying, fitting and fixing including labour charge of under drainage with 150 mm dia PVC manifold and 63 mm dia PVC laterals and interconnection of the filter unit including necessary GI fittings. (ix) supplying and charging of filter media considering all materials for the filter bed constructed as per the specification provided by the deptt. The specification of the sand and gravel is as below: (a) Sand should be hard, resistant quartz, free from clay, fine particles, soft grains, organic matter and dirt. Effective size of sand (d10) has to be within the range from 0.45 mm to 0.7 mm and uniformity coefficient (d60/d10) within 1.3 to 1.7. The effective depth of sand bed has to be 0.60 m. (b) Gravel has to be hard preferably rounded stone and not crushed stone, with average specific gravity not less than 2.5 |
| 51 | Supplying,fitting,fixing of internal connection between TP & UGR including labour charge and materials which includes the following jobs: a. Earth work in excavation in foundation trenches (of size 1 x 1 x 18.00 m x 0.60m x 0.90m=9.72 Cu.M) including refilling the quantity as necessary after completion of works of pipe line dressing, ramming, watering etc as directed by the Deptt. b. Supplying of UPVC perforated laterals of 50mm dia and 60 cm long by making hole of 5mm dia at a spacing of 8 cm centre to centre in two lines at 60 degree with the centre of the pipe and threading at both ends and supplying, fitting and fixing 40mm dia U.P.V.C. threaded End Plug at one end, the other end to be fitted with a UPVC threaded nipple of 75 mm long properly embedded in RCC cover slab all complete. c. Providing precast R.C.C slab over drain ,septic tank etc. in prop. 1:3/2:3 reinforced with 10mm M.S. bar @ 150mm centre both ways tying with 20 gauge black annealed wire with necessary shuttering , curing etc. complete including fixing in position as directed. d. Supplying and placing of filter sand of hard and resistant quartz, uniform size and shape free from dust, clay, soft grains, dirt and any other foreign materials includind inorganic salt and organic substance, washed and screened. Having uniformity coefficient between 1.3 to 1.7, effective size between 0.45 to 0.70mm, ignition loss not exceeding Please Enable Macros to View BoQ information |
AI Tender Summary
Tender Timeline
Jul 14, 2026
11:30 IST
Tender Published
Tender notice published.
CompletedAug 04, 2026
17:00 IST
Bid Submission Deadline
Online submission via eProcurement portal.
Upcoming · 6 daysAug 05, 2026
Bid Opening Date
Technical bids will be opened and evaluated.
Upcoming · 7 daysTender Documents
Download All (ZIP) ↓
Disclaimer
We takes all possible care for accurate & authentic tender information. However users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender