Tender For Rrd Of Lwss Chintpuni (Amokla Pritam ) In Tehsil Amb Distt. Una (Hp) (S/H :-Construction Of 4 Nos Storage Tank )
Tender Value
25.29 Lakhs
Estimated cost
Bid Submission
23 Jul 2026
5 days left
EMD
50594
Bank guarantee accepted
Document Fee
2000
Non-refundable
Tender Type
Online
Tender Overview
Organization
Tender ID
Competition Type
NCB
Bidding Type
Tender
Location / State
Una → Himachal Pradesh
EMD Exemption
Not Available
Quantity
Not Available
Website
Contact Person
Address
Project Description
Tender for Rrd Of Lwss Chintpuni (Amokla Pritam ) In Tehsil Amb Distt. Una (Hp) (S/H :-Construction Of 4 Nos Storage Tank )
BOQ
| Sl. No. | Item Description |
| 1 | Excavation in foundations,trenches etc., in earth work, lift upto 1.50 mts. Stacking the excavated soil not more than 3 mts. Clear from the edge of the excavation & then returning the stacked soil in 15 cms. Layers,when required into plinths sides of foundation etc.,consolidating each deposited layers by ramming & watering & then disposing of all surplus excavated earth as dierected within all leads & lifts as per entire satisfaction of Engineer in charge. |
| 2 | Earth work without dewatering+ laying of rising main |
| 3 | Earth work with dewatering |
| 4 | Providing & laying cement concrete 1:3:6 (1cement : 3 sand : 6 graded stone aggregate 40 mm nominal size) excluding the cost of centring & shuttering in Foundation & plinth. |
| 5 | Providing & laying cement concrete 1:1.5:3 (1cement :1.5 sand : 3 graded stone aggregate 20 mm nominal size) & curing complete excluding the cost of form work & reinforcement for reinforced concrete work in :- |
| 6 | (i) Foundation,footing,bases of columns and the like & mass concrete. |
| 7 | (ii) Wall (any thickness but not less than 0.10 mts.Thickness)attached pillasters,buttresses plinth,& string courses etc.from top of found. level upto floor two level |
| 8 | Prov.form work with steel plates 3.15 mm thick welded with angle iron in frame 30 x 30 x 5mm,so as to give a fair finish i/c centring shuttering,strutting & propping etc. with wooden battens & ballies,ht. of propping & centring below supporting floor to ceiling not exceeding 4.00 mts. & removal of the same for in situ-reinforced concrete & plain concrete work :- |
| 9 | (i) Vertical surfaces such as wall (any thick.) partitions & the like i/c attached pillasters, buttresses,plinth & string courses & the like. |
| 10 | (ii) Flat surfaces such as soffits of suspended floor,roofs, landing & the like. |
| 11 | Prov.in RCC work smooth finishing of the exposed surface with cement mortor1:3(1cement :3 sand ) |
| 12 | Providing & laying cement concrete 1:2:4 (1cement :2 sand : 4 graded stone aggregate 20 mm nominal size) & curing complete excluding the cost of form work & reinforcement for RCC work in :- |
| 13 | (i) Suspended floor,roofs,landing & shelves & their support balconies , beams,girders, bressumers & cantilever upto floor level. |
| 14 | Providing Tor steel reinforcement for RCC work i/c bending,binding & placing complete upto floor two level. |
| 15 | Steel work welded in built up sections,trusses & framed work i/c cutting,hoisting & fixing in position & applying a priming coatof red paint :- In grating, framed ,guards,bars, ladders, railing,brackets & similar works. |
| 16 | laying in trenches GMS/MS Tubes (L/M class) tube fitting(Earth work in trenches to be measured & paid for separately) |
| 17 | Scour pipr -100 mm dia (M) |
| 18 | Providing & fixing CI Sluice valve (with hand wheel) as per IS : 780-1984 class-I upto 300 mm dia.(i/c brass spindle & as per 2906-1984 class-II for dia.> 300 mm) complete with bolts nuts,rubber insertion etc.,(the tail piece if required shall be measured & paid for separatly) |
| 19 | 100 mm dia |
| 20 | Constructing chamber for sluice valve, with CI surface box 100 mm top dia.,160 mm bottom dia. & 180 mm deep(inside) with chained lid RCC top 1:2:4 mix (1 cement :2 sand :4 graded stone aggregate 20 mm nominal size) 100mm thick foundation concrete 1:5:10 mix (1cement : 5 sand : 10 graded stone aggregate 40 mm nominal size) & inside plastering with cement mortor 1 :3 (1 cement : 3 sand) finished with a floating coat of neat cement i/c curing complete. 600 x 600 x 750 mm inside size With 150 mm thick walls of RCC 1:2 :4 (1 cement :2 sand :4 graded stone aggregate 20mm nominal size) complete with form work & reinforcement with 6 mm bars at not exceeding 150 mm centres both ways |
| 21 | Prov. & fixing SFRC Man hole cover with frame having frames size of 560 mm internal dia.should not be less than 100 kg |
| 22 | Stone filling behind the long wall facing towards U/S side |
| 23 | Supply and installation of Mono submersible pumping set of KSB/Calama/SU/Johnston make comprising to latest relevant BIS code . The pump should be fitted with bronze impellers of suitable alloys as per IS : 8034-1976 latest suitable for clear water having greased packed bearing and shaft with wound stator on motor side and with soft protection sleeve on pump side ensuring better life for shaft coupled to a submersible squirrel cage electric induction motor (water proof type) of required HP, RPM 2900/1450 rpm of reputed make confirming to BIS 9238-1979 latest with up to date amendments, totally dust and water proof for submersible duty isolated from the pump by intermediate casing with double mechanical seal in oil chamber and grease packed lubricated bearing and provided with stainless steel thrust bearing plate to with stand non vertical loads with minimum wear and tear. it should also be fitted with a device to take up expansion of water with the heating of motor. the power of electric motor should be at lates 10% in excess of minimum power required by the pump in the operation range (+) 10 % and (-) 25 % of duty point head. the motor should be as per IS : 325-1978 with up to date amendments. the pump set should include erection, clamps, cable clips etc. and suitable for operation on data as per direction of Engineer-in-charge. (1.)Head:- 77.52 Mtr ( 2.) Discharge :- 7.58 LPS ( 3.) Dia of Rising:- 100 mm. 4. Length of Rising L:- 210 RMT Mtr\\" |
| 24 | Providing and installation of complete panel board suitable for mono submersible pumping machinery including main Switches 100 Amp. 2 Nos L&T make MCCB standard make, Three Phase Indicating Lamps, Bus Bar Chamber, Copper Strip, Volt meter, Ampere Meter 2 Nos with Ctrs.A.e make Frequency Meter, MEI make Star Delta Starter complete in all respect. |
| 25 | Supply of PVC joint less flat water proof cable of 16.00 Sq.mm as per BIS 694-1998 (latest with up to date amendments) suitable for the pump sets offered from OCB to motor including all other electrical equipments / accessories such as thimble , flexible pipe , isolator , nuts and bolts , cable glands , clips etc. , laid in pipes or trenches under floor. The type , size and make shall be subject to approval of HPSEB authorities. |
| 26 | Providing lowering of GMS column pipe assembly of 80 mm dia with up to date amendments the col. Pipe should be extended up to 5.00 mtrs beyond the outer wall of the pump house in the direction of rising main . The col. pipe should properly jointed with the rising main including all necessary accessories like increaser /reducer /flanges , bends , etc. as per the direction of Engineer-in-charge with all leads and lifts. |
| 27 | Providing & fixing double flanged Cast Iron Non Return valve of following dia class PN 1.00 of Kirloskar/Leader make confirming to IS 780-1984 latest with up to date amendments having seat pressure 10.20 Kg/cm2 with M.S. Flange table-5 including nuts, bolts and gasket sheet within all leads and lifts. 80 mm dia |
| 28 | Providing & fixing double flanged Cast Iron Non Return valve of following dia class PN 1.00 of Kirloskar/Leader make confirming to IS 780-1984 latest with up to date amendments having seat pressure 10.20 Kg/cm2 with M.S. Flange table-5 including nuts, bolts and gasket sheet within all leads and lifts. 100 mm dia |
| 29 | Providing and installation of double flanged sluice valve of following sizes Bir/Kartar ISI marked and capable of with standing the normal pressure as per 10.20 Kg IS:14846-2000 class PN-1 brass steel spindle, Flange Table-5 complete with accessories. |
| 30 | Providing and installation of ICTP switches with HRC fuses of L&T/Havells make and suitable capacity as per IS 4064:1978 with up to date amendments. Three phase indicator lamps complete with toggle switches for individual motors as per IS:3452 (P-I&II). |
| 31 | Erection of all equipments from S. No. 1 to 6 i/c cost of tees, bends, tapers & any other fitting required as per site condition & as per direction of Engineer-in-char |
| 32 | Laying jointing and testing in trenches galvanised mild steel tube of medium grade P/E complete conforming to IS 1239-1978 (With upto date ammendments) including providing and fixing tube fitting such as union, socket etc (excluding cost of earth work in trenches, will be measured and paid for separately.) for the following dia as per direction and to the entire satisfaction of Engineer-in-charge |
| 33 | Providing circumferencial butt welded joints to with three layers of welding using 3mm & 4mm electrodees after levelling of MS pipe. The pipe ends according to relevent BIS and entire satisfaction of the Engineer-in-Charge i/c all leads & lifts. (100 mm dia) |
| 34 | P/F Cast iron sluice valve of diffrent makes i.el leader/Kartar /Kirloskar/ RG/Bir make duly ISI , sluice valve ( with hand wheel ) as per IS 14846/2000 class up to 300 mm dia including stainless steel spindle and as per ID 1538 class II for diameter more than 300 mm complete with volts , nuts , insertion etc. araled capable of with standing the normal pressure as IS: 14846-2000 complete in all r espect in place of damaged/ non functional sluice valve in the various schemes . (100 mm dia) Please Enable Macros to View BoQ information |
AI Tender Summary
Tender Timeline
Jul 13, 2026
11:30 IST
Tender Published
Tender notice published.
CompletedJul 23, 2026
17:00 IST
Bid Submission Deadline
Online submission via eProcurement portal.
Upcoming · 5 daysJul 23, 2026
Bid Opening Date
Technical bids will be opened and evaluated.
Upcoming · 5 daysTender Documents
Download All (ZIP) ↓
Disclaimer
We takes all possible care for accurate & authentic tender information. However users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender