Tender For Provision Of Additional Washrooms (02 Nos) At P-2 Building, Cgdhq-4 And Addition/ Alteration And Repair Of Roof Tiles At Admin Block Of Cgdhq-4, Kochi. 8333/E8
Tender Value
30 Lakhs
Estimated cost
Bid Submission
03 Aug 2026
13 days left
EMD
60000
Bank guarantee accepted
Document Fee
500
Non-refundable
Tender Type
Online
Tender Overview
Organization
Tender ID
Competition Type
NCB
Bidding Type
Tender
Location / State
Ernakulam → Kerala
EMD Exemption
Available
Quantity
Not Available
Website
Contact Person
Address
Project Description
Tender for Provision Of Additional Washrooms (02 Nos) At P-2 Building, Cgdhq-4 And Addition/ Alteration And Repair Of Roof Tiles At Admin Block Of Cgdhq-4, Kochi. 8333/E8
BOQ
| Sl. No. | Item Description |
| 1 | Demolition of concrete in ground floors and pavings n exc 15 cm thickness (below or above ground level) complete all as specified and directed. |
| 2 | Excavating in trenches, n exc 1.5 m wide and n exc 1.5 m in depth; for foundation, etc., or for shafts, wells, cesspits,manholes, pier holes, etc., n exc 10 sq m on plan and n exc1.5 m in depth and getting out hard dense soil |
| 3 | M&L PCC 1:4:8 Type D2 (using 40mm graded stone aggregate) as in foundaion, filling and mass concrete. complete all as specified and directed. |
| 4 | M/L Precast cement concrete solid blocks masonry exc 10 cm in width in pcc 1:3:6 type C1, using 20 mm graded stone aggregate & set in cement motar 1:4, complete all as specified and directed. |
| 5 | M&L for RCC nominal mix 1:2:4 (20 mm graded stone aggregate) for slabs supported on walls, plinth beams and columns in floors, roofs, landings, balconies, canopies, deck slabs and in shelves and the like complete all as specified and directed. |
| 6 | Use wand waste for Formwork to sides and soffits of flat surfaces floor or roof beams, beam aunchings, girders, bressummers, lintels, cantilevers, shelves including sup- ports, overhangs, etc. also splays between floors and beams, etc complete all as specified and directed. |
| 7 | M&L for Mild steel bars 10 mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9 mm dia or securing with clips complete all as specified and directed. |
| 8 | All as per item No: 7, here-in-before but for 5 mm dia and over upto and including 10 mm dia in stirrups, spacers and binders complete all as specified and directed. |
| 9 | M & L for hardcore of brocken stone gauge n,exc 63 mm deposited spreed and leveled in layers n,exc 15 cm thick water and rammed to true surfaces complete all as specified and directed. |
| 10 | M&L for PCC 1:3:6 type C-2, using 40 mm graded crushed stone aggregate as in sub base complete all as specified and directed. |
| 11 | M&L for cement and sand mortar as in screed bed 15 mm thick in CM 1:4 complete all as specified and directed |
| 12 | M&L for Non - skid Ceramic tiles 7 to 8 mm thick (square/rectangular) area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match complete all as specified and directed. |
| 13 | M&L for Rendering 10 mm thick on fair faces of brick work or concrete surface as in CM 1:3 as in backing coat complete all as specified and directed |
| 14 | M&L for Glazed ceramic joint free tiles in vertical surface 350 x 250 x 7 mm/ 450 X 350 X 7 mm thick set and jointed in neat cement slurry and pointed in white or colour cement to match |
| 15 | M&L for Glazed earthware/ stoneware design as approved wall cladding joint free tiles in vertical surface 200 X 100 X 7 mm thick set and jointed in neat cement slurry and pointed in white or colour cement to match |
| 16 | Taking down cement or cement lime plaster, any description complete all as specified and directed. |
| 17 | M&L for rendering 10 mm thick on fair faces of brick work or concrete surfaces in CM 1:6 complete all as specified and directed. |
| 18 | M&L for rendering 15 mm thick on fair faces of brick in cement mortar 10 mm thick 1:6 and 5 mm tk 1:4 work or concrete surfaces shall be smooth without using extra cement complete all as specified and directed |
| 19 | S&F for factory made single extruded WPC (Wood Polymer Composite) solid door/ window/ Clerestory windows & other Frames/ Chowkhat of size 65 x 100 mm comprising of virgin PVC polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) fabricated with miter joints after applying PVC solvent cement and screwed with full body threaded star headed SS screws having minimum frame density of 750 kg/ cum, screw withdrawal strength of 2200 N (Face) & 1100 N (Edge), minimum compressive strength of 58 N/mm2, modules of elasticity 900 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/ moisture proof and fire retardant and fixed in position with MS hold fast/ lugs/SS dash fasteners of required dia and length complete as per direction. (M.S. hold fast/ lugs or SS dash fasteners shall be paid for separately). Note: For WPC solid door/window frames, minus 5mm tolerance in dimension i.e. depth and width of profile shall be acceptable. Variation in profile dimensions on plus side shall be acceptable but no extra payment on this account shall be made. complete all as specified and directed |
| 20 | Providing and fixing 35 mm thick factory made single extruded WPC (Wood Polymer Composite) solid decorative type flush door shutter of size 30 mm thick comprising of virgin polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/ wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) having minimum density of 650 kg/cum and screw withdrawal strength of 1800 N (Face) & 900 N (Edge), minimum compressive strength 50 N/mm2, modulus of elasticity 850 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/moisture proof and fire retardant. WPC to be laminated with PVC foil of minimum 14 microns thick of approved design pasted with hot melt adhesive on both faces of shutter and fixing with stainless steel butt hinges of required size with necessary full body threaded star headed counter sunk S.S screws, all as per direction of EngineerIn- Charge. (Note: stainless steel butt hinges and necessary S.S screws shall be paid separately) |
| 21 | M&L Bands, straps, supports or stays for rainwater, ventilating pipes, including bolts, if required: hooks (stay), heavy, for large gates; hook and pintle hinges: large hasps and staples; chains; hand made sliding bolts; clamps; hold fasts; wall ties; hooks for hanging fans; plain angle cleats for securing purlins to wood trusses or rafters; knee piece inserts; two way and three way straps, plate washers and similar small articles conforming to Fe-290 Gde-E-165 complete all as specified and directed |
| 22 | M&L for cement concrete 1:3:6 roviding, cement concrete in roof kerbs or mud stops, rounded or chamfered on edges in lintels upto 1.5 m clear span, cills, steps; seismic and other similar bands, plinth courses, string courses, lacing courses, parapets and railings upto 60 cm in height, copings, kneelers, apex stones, bed plates, kerbs not provided for in Item 04028, water troughs and the like including weathering, slightly rounded or chamfered angles and throating, complete all as specified and directed |
| 23 | S&F 100 mm Butt hinges, extruded aluminium alloy with galvanised mild steel hinge pin, anodised and fixed type C-22 complete all as specified and directed |
| 24 | S&F 200 mm long Brass barrel tower bolts, with cast or sheet barrel of extruded section and rolled or cast bolts and fixed complete all as specified and directed |
| 25 | S&F 150 mm long D type extruded brass handles, fabricated type polished complete all as specified and directed |
| 26 | M&L for 300 mm long Brass, sliding door bolt with sand or die-cast brass hasp, staple (bolt type) and fixing bolt with rolled or drawn brass bolts and fixed complete all as specified and directed |
| 27 | Providing and applying plaster of paris putty of 1 mm thickness over plastered /old untreated surface to prepare the surface even and smooth. complete all as specified and directed |
| 28 | M&L for Distempering with 1st quality acrylic distemper (ready mixed) having VOC content less than 50 gms/ litre, of approved manufacturer, of required shade and colour complete, as per manufacturer's specification. Two or more coats on new work or old un decorated surfaces complete all as specified and as directed. |
| 29 | Material & Labour for applying Two or more coats of 100% Premium acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489 : 2004, Alkali & fungal resistance, dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives @ 1.43 litre/ 10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/ 10 sqm over new /old untreated surfaces, complete all as specified and as directed. |
| 30 | S&F 20 mm bore 3-layer PP-R ( Polypropylene random copolymer ) concealed pipes SDR 7.4 (PN 16) UV stabilized and antimicrobial fusion welded having thermal stability for hot & cold water supply including all PP-R plain & brass treaded polypropylene random fittings fixed complete to walls, ceilings or in floors etc, complete all as specified. |
| 31 | S&F 25 mm bore 3-layer PP-R ( Polypropylene random copolymer ) concealed pipes SDR 7.4 (PN 16) UV stabilized and antimicrobial fusion welded having thermal stability for hot & cold water supply including all PP-R plain & brass treaded polypropylene random fittings fixed complete to walls, ceilings or in floors etc, complete all as specified. |
| 32 | S&F PP-R 25 mm bore Gate valves (brass insert) as per requirement of the site complete all as specified and directed. |
| 33 | S&f 75 mm bore PVC (SWR) pipe single socketed , in any length with rubber joints laid in trenches or in floors. |
| 34 | S&F PVC (SWR) pipe 110 mm bore single socketed ,in any length with rubber ring joints, laid in trenches or in floors cement complete all as specified |
| 35 | S&f 75 mm bore PVC (SWR) pipe bends any radius |
| 36 | S&F PVC (SWR) 110 mm bore bends any radius, complete all as specified |
| 37 | S&F PVC (SWR) 110 mm bore junction single (single T), complete all as specified |
| 38 | S&F 75 mm bore PVC (SWR) junction single, (Single T) equal or unequal |
| 39 | M&L 75 mm bore PVC (SWR) multi floor trap with grating including jointing with solvent cement |
| 40 | S&F PVC (SWR) 75 mm bore vent cowl complete all as specified |
| 41 | S&F PVC (SWR) 'S' trap 110 mm bore for EWC/ IWC all as specified and directed. |
| 42 | S&F single piece china wash down water closet , Rimless Bowl with cistern for coupled W/c with UF soft close slim seat cover, hinges, dual flush cistern fitting, conversion bend, fixing accessories and accessories set, size: 380 x 645 x 805 mm, S Trap-250 mm Make: jaquar Cat No. OPS-WHT-15753NS250UFSMZ or equivalent in Parryware / CERA. |
| 43 | S&F wash hand basin table top type Thin Rim Table Top Basin, Shape - Round, fixed on granite top grooving and cutting if required in size of Size: 455 x 455 x 110 mm Make: Jaquar cat No JDS-WHT-25939or Equivalent in Parryware / CERA complete all as specified. |
| 44 | S&F Vitreous China Urinal, Half stall type, white (excluding flushing cistern, flush Vitreous China urinals, (back or corner wall type), complete including providing and fixing plugs, bedding urinal against wall in cement mortar 1:2, securing urinal to plugs with and including 60 mm long brass screws, pointing around urinal back in cement, complete all as specified and directed. |
| 45 | S&F Urinal spreader of PTMT any colour for fixing with 15 mm dia pipe suitable for urinal, complete all as specified and directed. |
| 46 | S&F single lever Basin mixer without popup waste system with 450mm long braided hoses complete all as specified and directed.Make: Jaquar Cat No. VGP-81011B or equvalant in Parryware / CERA |
| 47 | S&F 6 mm thick bevelled edged mirror of any size and descripiton fixed with stainless steel spacer complete all as specified and directed. |
| 48 | S&F Jaquar Allied Health Faucet Kit ALD-573 flexible chrome hose, handset & bracket. 1.2 metre long flexible tube and wall hook, complete all as specified and directed. |
| 49 | S&F chromium plated toilet Roll holder fixed on walls complete all as specified and directed. Make: Jaquar Cat No: CAN-1151N or equvalant in Parryware / CERA . |
| 50 | S&F angle valve with wall flange 15 mm bore cast copper alloy fancy type, chromium plated with cup complete all a specified and directed. Make: Jaquar Cat No: VGP-81053 or eqivalent in Parryware / CERA . |
| 51 | S&F chromium plated brass bib tap fancy type screwed down ,screwed for iron pipe or for brass ferrule 15 mm bore complete all a specified and directed Make: Jaquar Cat No:VGB-81037 or eqivalent in Parryware / CERA . |
| 52 | S&F towel rack 600 mm long with lower hanger, stainless steel fixed to walls with screws and fisher complete all as specified and directed. Make: Jaquar Cat No. CAN-11818 or equivalent in Parryware / CERA |
| 53 | S&F CP brass towel ring fixed with and incl CP brass screws and complete all a specified and directed .Make: Jaquar Cat No: CAN-1121BN) or equivalent in Parryware / CERA |
| 54 | S&F Soap dish fixed with and including CP brass screws complete all a specified and directed Make: Jaquar Cat No: ACN-1131N or equivalant in Parryware / CERA |
| 55 | S&F Soap dispensor fixed with and incl CP brass screws complete all a specified and directed. Make: Jaquar (Kubix) Cat No: CAN-1135N or equivalent in Parryware / CERA |
| 56 | S&F chromimum plated brass 32 mm click clake waste coupling for table top wash hand basin half or full thread fixed complete all as specified and directed. (Make: Jaquar Cat No. ALD-729L130) or equivalent in Parryware / CERA. |
| 57 | S&F 32 mm bore brass chromium plated bottle traps for wash basins, sinks, urinals etc with inlet and outlet screwed for pipe or connection including necessary packing, union and cap complete all as specified and directed. |
| 58 | S&F PVC connections 15mm size with CP nuts of length 600mm complete all a specified and directed. Make: Jaquar Cat No. ALD-8058 or equivalent in Parryware / CERA. |
| 59 | S&F Glass corner sutable size for bath Room with Stainless steel guard complete |
| 60 | S&F18/19 mm thick PVC solid double side prelam celluca board/MDF board with lamination of approved colour fixed with screws as in modular kitchen cabinets/cupboards complete all as specified and directed. |
| 61 | M&L for 20 mm thick rubby pink or Rubby red granite (of any type) work (table rubbed and polished) in steps, jambs, pillars, window-cills, cooking platforms and like including pointing with admixture of pigment to match with shade of granite complete all as specifeid and directed. |
| 62 | Providing edge moulding to 18-20 mm thick stone of counters vanities etc. including machine polishing to edge to give high gloss finish etc. complete all as specifeid and directed. |
| 63 | S&F MS bright polished auto hinges suitable for cupboard/cabinet fixed with screws as per manufacture instructions complete all as specified and directed. |
| 64 | S&F 100 mm long extruded brass handles, fabricated type polished complete all as specified and directed. |
| 65 | S&F Grating doom 125 mm with waste hole of PTMT. |
| 66 | Providing and fixing Seamless calcium silicate ceiling made out of 1800 x 1200 mm size board of siliceous and calcareous material reinforced with cellulose fibre fixed to the ceiling section with 25 mm long self drilling and tapping screws having phillips head with under head cutter at 200 mm centre to centre,including finshing the joint of face board with specially formulated jointing compound and 48 mm wide fibre tape to provide seam less finish (Frame work for ceiling shall be measured and paid separately) or metal frame work and reinforced with G.I. wire mesh (Fillets, metal frame work and G.I. wire mesh paid separately),with fibre glass sheet fixed where required for lighting arrangements, Gl frame work for seamless ceiling comprising of Gl perimeter channnel 0.55 mm thick with two unequal flanges of 20 and 30 mm and web of 27 mm fixed to surrounding wall using nylon sleeves and screws at 450 mm centre to centre/intermediate channel 0.9 mm thick having two equal flanges of 15 mm each and web of 45 mm suspended from soffit at approx 900 mm centre to centre with Gl cleat and steel expansion fasteners with and including ceiling section (not exc 1.2 m length) of 0.55 mm thickness having kurled web of 50 mm and flange of 26 mm each with lips of 10.5 mm fixed to the intermediate channel with connecting clips across the intermediate channel at 457 mm centre to centre. Hangers 6 mm dia. G.I. (upto 1200mm length) adjusting level fixed to roof slabs by means of ceilling cleats made out of G.I. flat 40 x 3 mm size 60 mm long and expansion hold fasteners 12.5mm dia. 40mm long complete all as specified and directed. |
| 67 | M&L for steel work in tubular trusses incluidng special shaped washer etc complete using ERW or induction butt welded tubes confirming to IS complete all as specified and directed. |
| 68 | M&L for preparation of new or previously untreated steel surfaces of any description over 10 cm in width or girth, not other wise described and applying two coats of synthetic enamel paint over a coat of red oxide primer complete all as specified and directed. |
| 69 | S&F Pre-painted galvalume aluminium zinc coating GI based corrugated steel sheet 0.50 mm thick of an colour having tensile strength of 550 mpa as in roof covering/cladding to wall, fixed with self tapping screws complete all as specified and directed. |
| 70 | S&F in repair door closer hydraulically regulated designation No 3 universal type, aluminium body suitable for door shutters of up to 700 mm in width and weight not more than 35 Kg and fixed complete all as specified and directed. |
| 71 | S&F Roof tiles, Mangalore pattern, interlocking at side joints, laid dry complete all as specified and directed. |
| 72 | Dismantling Single layer Mangalore pattern or similar tiles in roofing bedded complete all as specified and directed. |
| 73 | Demolition of Concrete of any description and in any position not otherwise Roofs, floors (other than ground floors), beams, staircases, landing, chajjas and similar suspended work complete all as specified and directed. |
| 74 | Material and labour for 25 mm thick cement concrete 1:2:4 type B0 using 12.5 mm graded stone aggregate as in as in beams, cantilever, lintels over 1.5 m span etc, complete all as specified and as directed. |
| 75 | M&L for Rendering 15mm thick on fair faces of brick in cement mortar 1:4 , work or concrete surfaces including 3% of weight of cement water proofing compound, shall be smooth without using extra cement complete all as specified and directed (WPC shall be measured and paid separately). |
| 76 | Supply only Water proofing compound liquid complete all as specified and directed. |
| 77 | Material and Labour for cement mortar band in CM 1:4 of size width 70mm at bottom 25mm at top and 40mm thick at 30 cm centre to centre for laying of any type and size of mangalore pattern tiles complete all as specified and directed. |
| 78 | Material and labour for glossy finish colour as approved roof tiles, Mangalore pattern, any type and pattern as approved, interlocking at side laid dry/wet complete all as specified and as directed. |
| 79 | Material and labour for Ridge or hip tiles to suit Mangalore pattern of roofing tiles, bedded and jointed in lime mortar 1:3 or cement mortar 1:6 complete all as specified and directed. |
| 80 | M&L for Providing, cement concrete Type Bo 1:2:4, as in roof kerbs or mud stops, rounded or chamfered on edges complete all as specified and directed. |
| 81 | Material & Labour for applying two or more coats of 100% Premium acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives @ 1.43 litre/ 10 sqm over new /old untreated surfaces. complete all as specified and directed. (The rate inclusive for steel scafollding up to top of building for painting) |
| 82 | Schedule of Credit (Minus) Rs.6000.00 NOTE: Bidder shall insert credit amount of Rs.6000.00 as rate in Green field under Col-13. Please Enable Macros to View BoQ information |
AI Tender Summary
Tender Timeline
Jul 13, 2026
11:30 IST
Tender Published
Tender notice published.
CompletedAug 03, 2026
17:00 IST
Bid Submission Deadline
Online submission via eProcurement portal.
Upcoming · 13 daysAug 10, 2026
Bid Opening Date
Technical bids will be opened and evaluated.
Upcoming · 20 daysTender Documents
Download All (ZIP) ↓
Disclaimer
We takes all possible care for accurate & authentic tender information. However users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender