Tender For Provision Of Toilet Block At Shms And Aty Bde C At Nurla Military Station Under Age(I) Nimu.
Tender Value
50.20 Lakhs
Estimated cost
Bid Submission
10 Aug 2026
19 days left
EMD
1 Lakhs
Bank guarantee accepted
Document Fee
1000
Non-refundable
Tender Type
Online
Tender Overview
Organization
Tender ID
Competition Type
NCB
Bidding Type
Tender
Location / State
Leh → Ladakh
EMD Exemption
Available
Quantity
Not Available
Website
Contact Person
Address
Project Description
Tender for Provision Of Toilet Block At Shms And Aty Bde C At Nurla Military Station Under Age(I) Nimu.
BOQ
| Sl. No. | Item Description |
| 1 | Surface Excavation n exc 30 cm deep and averaging 15cm deep and getting out hard and dense soil complete all as specified and as directed by Engineer-in-Charge. |
| 2 | Excavation over areas, n. exc. 1.5m deep hard/dense soil and getting out complete all as specified and as directed by Engineer-in-Charge. |
| 3 | Excavation over areas, exc. 1.5m and n exc 3.0m deep hard/dense soil and getting out complete all as specified and as directed by Engineer-in-Charge. |
| 4 | Excavation in trenches n.exc 1.5m wide and n.exc 1.5 m in depth for foundations and getting out in hard/dense soil complete all as specified and as directed by Engineer-in-Charge. |
| 5 | Earth work in excavation by mechanical means (Hydraulic excavator) means over areas in all kind of soil (exceeding 30 cm in depth. 1.5 m in width as well as 10 sqm on plan) including getting out and disposal of excavated earth lead upto 50 m and lift upto 1.5 m complete all as specified and as directed by Engineer-in-Charge. |
| 6 | Earth work in excavation by mechanical means (Hydraulic excavator) means over areas in all kind of soil (exceeding 1.5m in depth but not exceeding 3 m in depth. 1.5 m in width as well as 10 sqm on plan) including getting out and disposal of excavated earth lead upto 50 m and lift upto 1.5 m complete all as specified and as directed by Engineer-in-Charge. |
| 7 | Returning, filling in, including spreading, levelling, watering and well ramming in layers not exc. 25 cm thick complete all as specified and as directed by Engineer-in-Charge. |
| 8 | Removing excavated material n. exc 50 M and depositing where directed at a level not exc1.5 M above the starting point complete all as specified and as directed by Engineer-in-Charge. |
| 9 | Material and labour stone walling of random rubble, uncoursed well bounded, bedded and solidly hearted built in 1:6 brought to course complete all as specified and as directed by Engineer-in-Charge. |
| 10 | All as above item but laid in dry complete all as specified and as directed by Engineer-in-Charge. |
| 11 | Material and labour reinforced cement concrete type B1 1:2:4 (using 20 mm graded stone aggregate ) as in slab supported on walls beams and colums in floors, roofs, landing balconies, baffle wall etc complete all as specified and as directed by Engineer-in-Charge. |
| 12 | Material and labour reinforced precast cement concrete type B1 1:2:4 (Using 20 mm graded stone aggregate) as in cover slabs man hole etc ) and set in cement mortar 1:4 complete all as specified and as directed by Engineer-in-Charge. |
| 13 | Material and labour form work to edges of concrete flats, RCC/PCC bands floors roofs and similar works exc 10 cm and not exc 20 cm wide surface finished rough to receive plaster complete all as specified and as directed by Engineer-in-Charge. |
| 14 | Mild steel TMT 6 mm to 8 mm dia., cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with mild steel wire (annealed) not less than 0.9 mm dia., or securing with clips complete all as specified and as directed by Engineer-in-Charge. |
| 15 | Material and labour for Plain Cement Concrete Type D2 1:4:8 (using 40 mm graded stone aggregate) in foundations, filling and mass concrete complete all as specified and as directed by Engineer-in-Charge. |
| 16 | Material and labour for RCC M-30 Design mix (using 20mm graded crushed stone aggregate) as in Foundations, including rafts, footings, foundation beams; plinth beams; bases for columns, etc.; basement slabs,under-reamed piles and mass concrete complete all as specified and as directed by Engineer-in-Charge. |
| 17 | Material and labour for RCC M-30 Design mix (using 20mm graded crushed stone aggregate) as in Beam, Tie beam etc complete all as specified and as directed by Engineer-in-Charge. |
| 18 | Material and labour for RCC M-30 Design mix (using 20mm graded crushed stone aggregate) as in Columns, pillars, piers, posts and struts complete all as specified and as directed by Engineer-in-Charge. |
| 19 | M& L for RCC M-30 Design Mix Slab supported on walls,Beams and columns in floors, roofs, landing, balconies,canopies,deck slab and in shelves complete all as specified and as directed by Engineer-in-Charge. |
| 20 | Material and labour for Mild steel TMT bars 10 mm dia., and over cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with mild steel wire (annealed) not less than 0.9 mm dia., or securing with clips etc complete all as specified and as directed by Engineer-in-Charge. |
| 21 | Material and labour for mild steel TMT bars 5 mm dia and over upto and including 10 mm dia in strirrups, spaces and binder and including mild steel wire (annealed) not less than 0.9mm dia etc complete all as specified and as directed by Engineer-in-Charge. |
| 22 | Material and labour form work to sides of concrete with fair finishes, foundations, footings, bases of columns, raft and raft beams, sides and soffits (if any) of foundation and plinth beams and similar work, vertical or to batter complete all as specified and as directed by Engineer-in-Charge. |
| 23 | Material and labour form work fair finishes to side of Pillars, posts, struts,piers,columns & stanchions complete all as specified and as directed by Engineer-in-Charge. |
| 24 | Material and labour Formwork rough finishes to soffits of suspended slabs such as roof slabs, floor slabs,landing and similar work; not exceeding 200mm thick (Horizontal or sloping) complete all as specified and as directed by Engineer-in-Charge. |
| 25 | Formwork to sides and soffits offloor or roof beams, beam haunchings, girders, bressummers, lintels, cantilevers, shelves including sup- ports, overhangs, etc. also splays between floors and beams, etc complete all as specified and as directed by Engineer-in-Charge. |
| 26 | Supply and fix Roof trusses (framed), trussed,purlins, crane gantries, rails and fastenings and heavy bracket framing (Beam, tee, angle, channel or flat sections) including distance pieces, cleats etc F also fastening and fixing Fe 410-W (Gde E-250) quality -A complete all as specified and as directed by Engineer-in-Charge. |
| 27 | Material and labour for preparation of new surfaces of steel of any description not otherwise described over 10 cms in width or girth and applying two coat of synthetic enamel paint over a coat of red oxide primer complete all as specified and as directed by Engineer-in-Charge. |
| 28 | Supply and fix Pre- painted galvalume aluminum zinc coating GI based corrugated steel sheet 0.50mm thick of an colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws complete all as specified and as directed by Engineer-in-Charge. |
| 29 | Supply and fix Pre-painted galvalume aluminum zinc coating GI based Plain steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws complete all as specified and as directed by Engineer-in-Charge. |
| 30 | Material and labour 200 mm thick Hard core, of broken boulder/ stone broken to gauge n exc 63 mm complete all as specified and as directed by Engineer-in-Charge. |
| 31 | Material and labour Hardcore broken stone / boulder of gauge n exc 63 mm deposited, spreading and levelled in layers not exe 150 mm thick watered and well rammed to a true surfaces complete all as specified and as directed by Engineer-in-Charge. |
| 32 | Material and labour for 100 mm thick Moorum/Red bajri , spread,Kankar or laterite, spread, rolled and consolidated to gradient and camber required complete all as specified and as directed by Engineer-in-Charge. |
| 33 | Material and labour for 100 mm thick cement concrete type D-2, 1:4:8 (using 40mm aggregate) in sub base of floors complete all as specified and as directed by Engineer-in-Charge. |
| 34 | Material and labour for 75 mm thick cement concrete type D-2, 1:4:8 (using 40mm aggregate) in sub base of floors complete all as specified and as directed by Engineer-in-Charge. |
| 35 | Material and labour for 25 mm thick cement concrete type B-1, 1:2:4 (using 20 mm aggregate) in base of floors complete all as specified and as directed by Engineer-in-Charge. |
| 36 | Material and labour for white non-skid coloured Ceramic tiles 7 to 8 mm thick (square/ rectangular) area of each tile exceeding 0.06 sqm but not exceeding 0.11 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match the existing surface laid over 20mm thick average screed bed in CM 1:6 complete all as specified and as directed by Engineer-in-Charge. |
| 37 | Material and labour for 15mm thick cement plaster in CM 1:6 on brick work or concrete surfaces, finishing the surfaces even and smooth without using extra cement complete all as specified and as directed by Engineer-in-Charge. |
| 38 | Material and labour for Non - skid coloured Ceramic tiles 7 to 8 mm thick (square/ rectangular) area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm, in floors etc. over 15mm thick Screed bed or bedding layer of mortar 15 mm thick for laying floor finishes in CM 1:4 set and jointed in neat cement slurry and pointed in white or coloured cement to match complete all as specified and as directed by Engineer-in-Charge. |
| 39 | Material and labour Glazed ceramic colour tiles in vertical surface 350x 250x 7 mm/ 450X 350X 7mm thick set and jointed in neat cement slurry and pointed in white or colour cement to match over and including 10 mm thick rendering in CM 1:4 complete all as specified and as directed by Engineer-in-Charge. |
| 40 | Material and labour 12 mm thick rendering on fair faces of brick work or concrete surface in cm 1:6 to be finished even and smooth without using extra cement complete all as specified and as directed by Engineer-in-Charge. |
| 41 | Material and labour 15 mm thick cement plaster in CM 1:4 on brick work or concrete surface other than fair face or brick work and finished surface even and smooth without using extra cement complete all as specified and as directed by Engineer-in-Charge. |
| 42 | Material and labour for preparation of newly plastered surfaces of walls including cornices, pillasters etc, and applying two coats of oil emulsion distemper over and including one coat of chalk whiting preparatory to distempering complete all as specified and as directed by Engineer-in-Charge. |
| 43 | Material and labour for preparation of newly plastered surfaces of walls including cornices, pillasters etc, and applying two coats of cement base paint over a coat of primer complete all as specified and as directed by Engineer-in-Charge. |
| 44 | Material and labour for 75mm thick in PCC 1:3:6 type C-1 as in plinth protection surface finished even and smooth without using extra cement complete all as specified and as directed by Engineer-in-Charge. |
| 45 | Material and labour for precast cement concrete block masonry with solid block exc 10 cms in width made with PCC 1:3:6 type C-1 (using 20 mm graded aggregate) and set in CM 1:6 complete all as specified and as directed by Engineer-in-Charge. |
| 46 | Supply and fix vitreous China Squatting pan 'Orrisa' pattern size 580x440mm white with integral foot rest, and jointing to PVC/CI bend and flush pipe complete including making good to floor complete all as specified and as directed by Engineer-in-Charge. |
| 47 | Supply and fix PVC flushing cistern dual type 10 Litres capacity incl all accessosaries complete all as specified and as directed by Engineer-in-Charge. |
| 48 | Supply and fix vitereous china wash hand basin, white, flat back of size 550 x 400 mm including brackets, cutting for pinning in ends of brackets or erecting stand and including PVC waste pipe complete all as specified and as directed by Engineer-in-Charge. |
| 49 | Supply and fix in repair vitreous china urinals, half stall type, complete including providing and fixing plugs, bedding urinal against wall in cement mortar 1:2 , securing urinal to plugs with and including 60 mm long brass screw, pointing around urinal back in cement incl provn of flush pipe, grating and union for discharge pipe,complete all as specified and as directed by Engineer-in-Charge. |
| 50 | Supply and fix 15mm bore Bib Tap Chromium plated fancy type complete all as specified and as directed by Engineer-in-Charge. |
| 51 | Supply and fix 15mm bore size pillar tap cast copper alloy chromium plated fancy type complete all as specified and as directed by Engineer-in-Charge. |
| 52 | Supply and fix 15mm bore Stop Valve (Angle Valve) chromium plated fancy type complete all as specified and as directed by Engineer-in-Charge. |
| 53 | Supply and fix PVC connection 15mm size with PTMT nuts of length 450mm complete all as specified and as directed by Engineer-in-Charge. |
| 54 | Supply and fix grating round 100mm size of PTMT complete all as specified and as directed by Engineer-in-Charge. |
| 55 | Supply and fix Soap dish, vitreous China white, approximate size 160x 160x90mm complete all as specified and as directed by Engineer-in-Charge. |
| 56 | Supply and fix 600x450mm bevelled edge mirror or selected quality galass, mounted on 6mm thick AC bldg board or commercial plywood and fixed to wooden plugs with CP brass screws and cup washers complete all as specified and as directed by Engineer-in-Charge. |
| 57 | Supply and fix 25mm outer dia 3-layer PP-R Polypropylene random copolymer) pipes SDR 7.4 & SDR 11 UV stablised and antimicrobial welded having thermal stability for hot & cold water supply including all PP-R plain & brass threaded polypropylene random fittings fixed complete to walls, ceilings or in floors etc complete all as specified and as directed by Engineer-in-Charge. |
| 58 | Supply and fix Rotational moulded polyethylene water storage tanks 1000 Ltrs capacity (cylindrical vertical with closed top) hoisted and fixed in position all as specified in SSR Part I complete all as specified and as directed by Engineer-in-Charge. |
| 59 | Supply and fix Vitreous china wash down water closed pan \\" Pedestal Pattern\\" white, with seat white closed pattern with flat bottom and cover mild steel chromium plated or aluminized hinging deviced including flush pipe and joint arrangements with fixing bolts etc including making good the distrubed portion of floor in cement concrete 1:2:4 type B-0, asin repairs complete all as specified and as directed by Engineer-in-Charge. |
| 60 | Supply and fix solid PVC door frame of size 50 mm x 47 mm made out of 5mm thick PVC sheet reinforced with mild steel square tube complete all as specified and as directed by Engineer-in-Charge. |
| 61 | Supply and fix Factory made solid panel PVC door shutter 30 mm thick (style) consisting of frame made out of M.S. tubes for top & bottom rails. M.S. frame shall be covered with heat moulded plain colour PVC ‘C’ channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail; Panelling of plain colour PVC sheet to be fitted in the M.S. frame welded / sealed to the stiles & rails with suitable PVC sheet beading, and joined together with solvent cement, suppling & fixing complete all as specified and as directed by Engineer-in-Charge. |
| 62 | Supply and fix aluminum anodized ‘D’ type handles 125 mm complete all as specified and as directed by Engineer-in-Charge. |
| 63 | Supply and fix 150 mm aluminium anodised barrel tower bolts of extruded section complete all as specified and as directed by Engineer-in-Charge. |
| 64 | Supply and fix 100 mm Butt hinges, extruded aluminium alloy with galvanised mild steel hinge pin, anodised and fixed, type B-21 complete all as specified and as directed by Engineer-in-Charge. |
| 65 | Supply and fix Second class softwood plain , solid, straight chowkats and frames, wrought, framed rebated on the solid, rounded or chamfered , put together with glue pinned at joints supplied and fixed complete all as specified and as directed by Engineer-in-Charge. |
| 66 | Supply and fix 30 mm thick second class soft wood glazed and skeleton shutters, open rebated and prepared to receive glass, gauze, etc. (without sash bars), edges of framing plain, chamfered or rounded. fitted with cut and mitred beads for securing glass, etc.; sizes of members of shutters as specified in SSR Part I, Section 8, clause 8.24 (a); supplied and fitted to chowkats complete all as specified and as directed by Engineer-in-Charge. |
| 67 | Material and labour for Preparing new varnished wooden surfaces of any description,staining with spirit not other wise described over 10 cm width or girth and applying two coats of varnish complete all as specified and as directed by Engineer-in-Charge. |
| 68 | Supply and fix 5.5 mm thick ordinary quality glass sheet in squares n exc 0.5 sqm in each pane fixed to door/windows for glazing with and including oil putty or aluminium beads and rubber packing complete all as specified and as directed by Engineer-in-Charge. |
| 69 | Supply and fix 100 mm aluminium anodised barrel tower bolt of extruded section and fixed complete all as specified and as directed by Engineer-in-Charge. |
| 70 | Material and labour PCC type B-0 1:2:4 (12.5 mm graded aggregete) as in floor, drain haunching , benching , coping and etc similar work complete all as specified and as directed by Engineer-in-Charge. |
| 71 | Supply and fix PVC (SWR) pipes single socketed in any length with rubber ring joints, laid in trenches or in floors bore of pipe 110 mm complete all as specified and as directed by Engineer-in-Charge. |
| 72 | Supply and fix PVC (SWR) bend 110mm bore complete all as specified and as directed by Engineer-in-Charge. |
| 73 | Supply and fix PVC (SWR) junction single,(Single T) 110mm bore equal or unequal bore complete all as specified and as directed by Engineer-in-Charge. |
| 74 | Supply and fix 75 mm dia PVC (SWR) pipes single socketed in any length with rubber ring joints, laid in vertically as vent pipe complete all as specified and as directed by Engineer-in-Charge. |
| 75 | Supply and fix PVC (SWR) vent cowl 75 mm dia complete all as specified and as directed by Engineer-in-Charge. |
| 76 | Material and labour for point wiring with PVC FRLS insulated single core cable of stranded copper conductors of size 1.5 sqmm, 1100 volt grade drawn in and including rigid PVC casing caping accessories lain on wall/ceiling surface and fixed with PVC saddles and back-plate and GI screws, including PVC insulated single core cable of stranded copper conductor of size 1.5 sqmm as earth continuous wire connected to common earth and PVC Board for housing like switches, sockets, fan regulators etc complete all as specified and as directed by Engineer-in-Charge for following :- |
| 77 | (a) One light point/one fan point controlled by one switch |
| 78 | (b) One 3 pin 5 amps socket outlet independent with cables 1.5 sqmm size |
| 79 | (c) One 3 pin 5 Amp socket outlet on same board with cables 1.5 sqmm size |
| 80 | All same as per item No 72 above but with conductor of size 4 sqmm (Nominal area) for one 3 pin socket outlet 15 Amps on independent board complete and earth continuity wire with 4 sqmm PVC insulated stranded copper conductor Cable complete all as specified and as directed by Engineer-in-Charge. |
| 81 | Supply and fix Socket 2 in 1, 5 pin 5 Amp flush type complete all as specified and as directed by Engineer-in-Charge. |
| 82 | Supply and fix Switch piano flush type 5 Amp, single pole, one way complete all as specified and as directed by Engineer-in-Charge. |
| 83 | Supply and fix Switch socket combination 2 in 1, 3 pin, 5 Amp flush type complete all as specified and as directed by Engineer-in-Charge. |
| 84 | Supply and fix Switch Socket Combination 2 in 1, 3 pin, 15/16 amp flush type Universal complete all as specified and as directed by Engineer-in-Charge. |
| 85 | Material and labour for ceiling rose surface Bakelite 65x50mm two to three terminal complete all as specified and as directed by Engineer-in-Charge. |
| 86 | Supply and fix LED light fitting 1x9W/1X10W bulkhead luminaires including LED light driver holder connecting up with three core flexible copper conductor cable of suitable size complete all as specified and as directed by Engineer-in-Charge. |
| 87 | Supply and fixing LED light fitting mirror type with high out put diffuser 2 feet, 10 watt 220 V AC decorative type with driver holder and LED lamp including connecting up with three core flexible copper conductor cable of suitable size complete all as specified and as directed by Engineer-in-Charge. |
| 88 | Supply and fix basic all purpose surface and wall mounted LED batten with polycarbonate housing and integreted electronic driver of cap 20 watt, 4 feet long, with all accessories complete all as specified and as directed by Engineer-in-Charge. |
| 89 | Supply and fix sheet metal powder coated versatile Double door SPN distribution board, 08 way suitable for MCB's fitted with copper bus bar rated 200amps, neutral link , earth bar and din rail suitable for use on 240 Volt, 50Hz complete all as specified and as directed by Engineer-in-Charge. |
| 90 | Material and labour for MCB SPN 63 Amp, 240V with 10KA breaking capacity of 'C' series in distribution boards complete all as specified and as directed by Engineer-in-Charge. |
| 91 | Supply and fix to MCB SP 6-32 Amp with 10KA breaking capacity of 'C' series in distribution boards with all accessories complete all as specified and as directed by Engineer-in-Charge. |
| 92 | Supply and fix of exhaust fan, engineering plastic body complete with louvers shutter, voltage 230V, 50 Hz, RPM 1200, Copper winding of sweep 250mm AC single phase with, blades, and frame and louvers of size 250 mm sweep complete all as specified and as directed by Engineer-in-Charge. |
| 93 | Material and labour for Earthing complete with galvanised steel earth plate electrode of size (600 x 600 x 6) mm thick buried directly into ground vertically to depth not less than 2.25 metre below normal ground level with top edge of earth plate at a depth not less than 1.5 metre below normal ground level, surrounded on all sides by alternate layers of 150 mm thick charcoal and common salt, connected to earh galvanised earth lead wire 4.0mm dia by means of lugs, bolts, nuts, washer, check nuts of galvanised iron or steel all as shown in Electrical plate No. 3, GI strip laid in dia 40 mm bore light grade GI Pipe laid in floor and fixed to wall with proper size of clamps and watering pipe of bore 20 mm dia GI light grade including wire mesh funnel, PCC, earth chamber pit (30X30X30cm) with PCC 1:2:4 type B-1 using 20 mm grade stone aggreate including form work cement mortar including CI Pit cover with frame necessary excavation and earth work in any type of soil including testing on complete all as specified and as directed by Engineer-in-Charge. |
| 94 | Supply, laying and testing cable XLPE Insulated ,screened, PVC bedded, galvanized steel strip or wire armoured, electric power cables (heavy duty) 1100 Volts grade with stranded aluminium conductor of size 10 sq mm 2 core complete all as specified and as directed by Engineer-in-Charge. |
| 95 | Material and labour for un reinforced pre cast concrete cable cover class LV type I, flat size 250 mm x 150 mm x 40 mm complete all as specified and as directed by Engineer-in-Charge. |
| 96 | Sand cushioning to under ground cable complete all as specified in clause 19.75 of SSR Part - I complete all as specified and as directed by Engineer-in-Charge. |
| 97 | Supply and fixing PP-R gate valves(brass insert) for 25 mm dia pipe as per requirement of the site complete all as specified and as directed by Engineer-in-Charge. |
| 98 | Material labour for drilling, tapping, Cast Iron / Ductile Iron/GI water main in position for branch connection with straight plain brass ferrule of same size for the internal dia size 20 mm complete all as specified and as directed by Engineer-in-Charge. |
| 99 | Material and labour for Preparation of new plastered surface of wall by making the surface smooth and applying two coat of oil bound distemper (OBD) over a priming coat of alkali primer complete all as specified and as directed by Engineer-in-Charge. |
| 100 | Supply and fix in single piece in art Ceramic Rimless Wall Hung Western Toilet , soft close seat cover, hinges, accessories set, cistern Space saving P trap Wall mounted Commode 570x360x370 Make:Hindware ,Somany or equivalant complete all as specified and as directed by Engineer-in-Charge. |
| 101 | Tubular towel rail, 20mm dia, 60 cm long, CP with a pair of brackets, fixed to wall with CP brass screw and PVC rowl plugs (fixed in repair), complete all as specified and as directed by Engineer-in-Charge. |
| 102 | Supply and fix wash hand basin oval type fixed on granite top grooving and cutting if required complete all as specified and as directed by Engineer-in-Charge. |
| 103 | Supply and fix in Vitreous China bowl urinal flat back, size of 465 x 355 x 265 mm white (minimum), with grating and union for discharge pipe (excluding flushing cistern, flush pipe and waste pipe) (back or corner wall type),complete including providing and fixing plugs, bedding urinal against wall in cement mortar 1:2, securing urinal to plugs with and including 60mm long brass screws, pointing around urinal back in cement; fixing automatic flushing cistern with brackets, flush pipe, grating and Union for discharge pipe. (Exclusive offixing supply pipe to flushing cistern, trap and waste pipe) complete all as specified and as directed by Engineer-in-Charge. |
| 104 | Supply and fix bevelled edge mirror of selected quality glass, fixed to wall with chromium plated brass spacer screws and cup wasers complete all as specified and as directed by Engineer-in-Charge. |
| 105 | Supply and fix HDPE water storage tank of capacity 500 Ltr, cylinderical vertical type, 3 layer, insulated with 75 mm thick PUF insulation of density 48 Kg/Cum covered with Lid having locking arangement including float valve high pressure PTMT with epoxy coated aluminium rod & high density plastic ball secured for iron pipe and fixed of 15 mm bore complete all as specified and as directed by Engineer-in-Charge. |
| 106 | Material and labour for 20mm thick granite (of any type) work (table rubbed and polished) in steps, pillars, cooking platforms and like in cement mortar 1:4 including ponting in white cement 1:2 using marble dust with admixture of pigment to match the shade of granite over and including 15 mm thick rendering in CM 1:4 complete all as specified and as directed by Engineer-in-Charge. |
| 107 | Material and labour for 20mm thick marble tiles machine cut in skirting/dado laid over cement screed and jointed with grey cement slurry including cutting and polishing of type complete all as specified and as directed by Engineer-in-Charge. |
| 108 | Material and labour reinforced cement concrete type B1 1:2:4 (using 20 mm graded stone aggregate ) as in slab supported on walls beams and colums in floors, roofs, landing balconies, baffle wall etc complete all as specified and as directed by Engineer-in-Charge. |
| 109 | Supply and fix A Factory made single extruded WPC (Wood Polymer Composite) solid door/ window/ Ceosetory windows & other Frames/ Chowkhat of size 45 x 70 mm comprising of virgin PVC polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/ wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) fabricated with miter joints after applying PVC solvent cement and screwed with full body threaded star headed SS screws having minimum frame density of 750 kg/ cum, screw withdrawal strength of 2200 N (Face) & 1100 N (Edge), minimum comp ressive strength of 58 N/mm2 , modules of elasticity 900 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/ moisture proof and fire retardant and fixed in position with MS hold fast/ lugs/SS dash fasteners of required dia and length complete as per direction of Engineer-in-Charge. Note: M.S. hold fast/ lugs or SS dash fasteners shall be paid for separately |
| 110 | Supply and fix Providing and fixing factory made single extruded WPC (Wood Polymer Composite) solid decorative type flush door shutter of size 30mm thick comprising of virgipolymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/ wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) having minimum density of 650 kg/cum and screw withdrawal strength of 1800 N (Face) & 900 N (Edge), minimum compressive strength 50 N/mm2 , modulus of elasticity 850 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/moisture proof and fire retardant. WPC to be laminated with PVC foil of minimum 14 microns thick of approved design pasted with hot melt adhesive on both faces of shutter and fixing with stainless steel butt hinges of required size with necessary full body threaded star headed counter sunk S.S screws, all as per direction of Engineer In- Charge. Note: Stainless steel butt hinges and necessary S.S screws shall be paid separately |
| 111 | Material and labour for providing and fixing Gypsum boards 9 mm thick PVC film on the face side and other side metalised polyster flim as in ceilings fixed with screws as per manufacturers instructions including anodised aluminium powder coated snap grid frame work of size 605 x 605 mm with anodised aluminium channel supports/ angles/ 'T' (Main tee 35 x 25 x 1.5 mm, cross tee 25 x 25 x 1.4 mm and wall angle 32 x 32 x 2 mm) fixed with screws/ plugs etc including GI suspenders of 6mm dia upto 1200 mm length adjusting level fixed to roof slabs by means of ceiling cleats made out of GI flat 40 x 3 mm size as per approved pattern and design complete all as specified and as directed by Engineer-in-Charge. |
| 112 | Supply and fix hand shower (health faucet ) with 8mm dia and 1 meter long CP flexible tube and wall hook complete all as specified Make: Cera, Jaquar , Marc & Hindware as per Sample complete all as specified and as directed by Engineer-in-Charge. |
| 113 | Supply and fix Aluminium die body door closer hydraulically designation No 3 universal type suitable for door shutter of 851 to 1000mm in width and weight 61 to 80 kg complete all as specified and as directed by Engineer-in-Charge. |
| 114 | Supply and fix insulation for GI/PP-R pipe of dia from 15 mm to 25 mm with resin bonded fibre glass wool roll and aluminium cladding of density 24 kg/Cum, with factory laminated aluminium vapour barrier, thickness of insulation as specified and including the following:- (a)Consist of Natral Foam tube 19 mm,rockwool 50 mm thich, Plastic wrap,Chicken Mesh wire Packing Tape and aluminum Sheet of 28 Gauge (b) Material and labour for cleaning the pipe surface to make the surface completely free of millscale, dirt, dust and other foreign materials, taking special care so that all pipe joints are sealed against any leakage. (c) Material and labour for clamping of pipe after insulations by U type clamp and scrws of requred lenth and scerued properly . Note :- (i)Rates of U type clamps and screws are demade in this quited rate. (ii) Rates of Natral Foam tube 19 mm,rockwool 50 mm thich, Plastic wrap,Chicken Mesh wire Packing Tape and aluminum Sheet of 28 Gauge are demade in this quited rate. |
| 115 | Supply and fix in testing and commissioning self limiting self regulating heat tracer 60-HTS, operated ( heat Cable Elthern ) on 240 Volt AC supply suitable for Gi pipe from 15 mm to 80mm dia complete all as specified and as directed by Engineer-in-Charge. |
| 116 | Material and labour for Thermostat for heat Cable Elthern of 0 to 80˚ C , connection and wiring complete all as specified and as directed by Engineer-in-Charge. |
| 117 | Supply and laying or fixing or passing through pipe, 16sq mm 2core 1100 volts grade heavy duty cable with PVC insulated aluminium conductor served with an inner sheathing of PVC tape armoured with galvanised steel wire or tape and overall PVC sheathed 16 sq. mm 2 CORE nominal cross section in service connections complete all as specified and as directed by Engineer-in-Charge. |
| 118 | Supply and fixing LED luminaire 600 mm x 600 mm, 35/36 watt, 220 V AC recessed type with high efficiency PMMA diffuser soft glare free light complete with driver, holders & LED lamp suitable for roof ceiling including connecting up with driver three core flexible copper conductor complete all as specified and as directed by Engineer-in-Charge. |
| 119 | Supply and fix electric water heater, storage type steel body with copper inner tank and heating element upto 2 KW capacity 25 litre, BEE 5 Star rated complete with all accessories such as safety valve, thermostate, NRV, connection piece etc complete all as specified and as directed by Engineer-in-Charge. |
| 120 | Supply and fix LED street light fitting 35 Watt 230 V AC outdoor type with high pressure die cast aluminum hosing and heat resistant complete with driver, lamp bracket with impact and corrosion resistant including thermal management in multiple optics complete with IP 65/66 protection complete all as specified and as directed by Engineer-in-Charge. |
| 121 | Material and labour for GI bracket 1.5 mtr long made out of GI pipe 40mm dia bend to suitable radius incl clamps nuts bolts washers incl painting with aluminum paint etc complete all as specified and as directed by Engineer-in-Charge. |
| 122 | Supply, laying and testing cable XLPE Insulated ,screened, PVC bedded, galvanized steel strip or wire armoured, electric power cables (heavy duty) 1100 Volts grade with stranded aluminium conductor of size 16 sq mm 4 core complete all as specified and as directed by Engineer-in-Charge. |
| 123 | Material and labour for Busbar chambers with 4 aluminium busbar strip of rating 400 Amp 6 way fixed on angle iron of size 40mm x40mm x5mm capacity with connected to busbar complete all as specified and as directed by Engineer-in-Charge. |
| 124 | Material and labour for Earthing complete with galvanised steel earth plate electrode of size (600 x 600 x 6.3) mm thick buried directly into ground vertically to depth not less than 2.25 metre below normal ground level with top edge of earth plate at a depth not less than 1.5 metre below normal ground level, surrounded on all sides by alternate layers of 150 mm thick charcoal and common salt, connected to MS galvanized earh strip of size 32 x 6 mm by means of lugs, bolts, nuts, washer, check nuts of galvanised iron or steel all as shown in Electrical plate No. 3, wire protected by dia 15 mm bore light grade GI Pipe laid in floor and fixed to wall with proper size of clamps and watering pipe of bore 20 mm dia GI light grade including wire mesh funnel, PCC, earth chamber pit with PCC 1:2:4 type B-1 using 20 mm grade stone aggreate including form work cement mortar including CI Pit cover with frame necessary excavation and earth work in any type of soil including testing on completion for desired result complete all as specified and as directed by Engineer-in-Charge. Please Enable Macros to View BoQ information |
AI Tender Summary
Tender Timeline
Jul 13, 2026
11:30 IST
Tender Published
Tender notice published.
CompletedAug 10, 2026
17:00 IST
Bid Submission Deadline
Online submission via eProcurement portal.
Upcoming · 19 daysAug 11, 2026
Bid Opening Date
Technical bids will be opened and evaluated.
Upcoming · 20 daysTender Documents
Download All (ZIP) ↓
Disclaimer
We takes all possible care for accurate & authentic tender information. However users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender