Tender For Construction Of Samajmandir At- Hiwari Tq- Maregaon Dist.- Yavatmal
Tender Value
22 Lakhs
Estimated cost
Bid Submission
27 Jul 2026
11 days left
EMD
22000
Bank guarantee accepted
Document Fee
590
Non-refundable
Tender Type
Online
Tender Overview
Organization
Tender ID
Competition Type
NCB
Bidding Type
Tender
Location / State
Yavatmal → Maharashtra
EMD Exemption
Not Available
Quantity
Not Available
Website
Contact Person
Address
Project Description
Tender for Construction Of Samajmandir At- Hiwari Tq- Maregaon Dist.- Yavatmal
BOQ
| Sl. No. | Item Description |
| 1 | 21.02 BDA 1 Excavation for foundation in earth, soil of all types, sand, gravel and soft murum, including removing the excavated material up to a distance of 50 m. beyond the building area and stacking and spreading as directed, ewatering, preparing the bed for the foundation and necessary back filling, ramming, watering including shoring and strutting etc. complete. (Lift upto 1.5 m.) By Mechanical Means Bd.A.1 Page One Number 259 One Cubic Metre 207/-(SSR Item no 21.02 ,Pge no. ) |
| 2 | 21.06 BDA 2 Excavation for foundation in hard murum including removing the excavated material upto distance of 50 metres beyond the building area and stacking and spreading as directed, dewatering, preparing the bed for the foundation and necessary back filling, ramming, watering including shoring and strutting etc. complete. (Lift upto 1.50 m) By Mechanical Means Bd.A.2 Page One Number 259 One Cubic Metre 227/-(SSR Item no 21.06 ,Pge no. ) |
| 3 | 21.40 BDA Providing soling using 80 mm size trap metal in 15 cm. layer including filling voids with Crushed sand/grit, ramming, watering etc. complete. As directed by Engineer in charge. One Cubic Metre 1454/-(SSR Item no 21.10 ,Pge no. ) |
| 4 | 21.37 Filling in plinth and floors with contractors material/brought from outside and approved by Engineer incharge in layers of 15 cm to 20 cm including watering and compaction etc. complete.(SSR Item no 21.37 ,Pge no. ) |
| 5 | 24.01 Providing and laying Cast in situ/Ready Mix cement concrete in M-10 of trap/ granite/ quartzite/ gneiss metal for foundation and bedding including bailing out water, Steel centering, formwork, laying/pumping, compacting, roughening them if special finish is to be provided, finishing if required and curing complete, with fully automatic micro processor based PLC with SCADA enabled reversible Drum Type mixer/concrete Batch mix plant (Pan mixer) etc. complete. With fine aggregate (Crushedsand VSI Grade)(SSR IteM 24.01 ,Pge no. ) |
| 6 | 25.11 BDF 3 Providing and laying in situ /Ready Mix cement concrete M-20 of trap / granite /quartzite/ gneiss metal for R.C.C. work in foundations like raft, strip foundations, grillage and footings of R.C.C. columns and steel stanchions etc. including bailing out water, Steel centering formwork, laying/pumping cover blocks, compaction and curing roughening the surface if special finish is to be provided (Excluding reinforcement and structural steel) etc. complete, with fully automatic micro processor based PLC with SCADA enabled reversible Drum Type mixer/ concrete Batch mix plant (Pan mixer) etc. complete. With fine aggregate (Crushed sand VSI Grade) Bd.F.3 Page One Number 298 and B.7, Page One Number38 One Cubic Metre 7104/-(SSR Item no 25.11,Pge no.) |
| 7 | 25.31 BDF 5 Providing and laying Cast in situ/Ready Mix cement concrete M-20 of trap / granite /quartzite/ gneiss metal for R.C.C. columns as per detailed designs and drawing or as directed including steel centering, formwork, cover blocks, laying/pumping, compaction finishing the formed surfaces with cement mortar 1:3 of sufficient minimum thickness to give a smooth and even surface or roughening if special finish is to be provided and curing etc. complete.(Excluding reinforcement and structural steel).with fully automatic micro processor based PLC with SCADA enabled reversible Drum Type mixer/ concrete Batch mix plant (Pan mixer) etc. complete. With fine aggregate (Crushed sand VSI Grade) Bd.F.5 Page One Number 300 and B.7, Page.One Number 38 One Cubic Metre 13783/-(SSR Item no 25.31 ,Pge no.) |
| 8 | 25.50 BDF 6 Providing and laying Cast in situ/Ready Mix cement concrete M-20 of trap / granite/quartzite/ gneiss metal for R.C.C. beams and lintels as per detailed designs and drawings or as directed including steel centering, formwork, cover blocks, laying/pumping, compactionand roughening the surface if special finish is to be provided and curing etc. complete. (Excluding reinforcement and structural steel). with fully automatic micro processor based PLC with SCADA enabled reversible Drum Type mixer/ concrete Batch mix plant (Pan mixer) etc. complete. With fine aggregate (Crushed sand VSI Grade) Bd.F.6 Page One Number 300 and B.7, Page One Number38 One Cubic Metre 12269/-(SSR Item no 25.50 ,Pge no.) |
| 9 | 26.05 Providing and laying Cast in situ/Ready Mixcement concrete M-20 of trap/ granite/ quartzite/ gneiss metal for R.C.C. chajja as per detailed design and drawings including steel centering, formwork, cover blocks, laying/pumping, compacting and roughening thesurface if special finish is to be provided and curing complete. (Excluding reinforcement and structural steel). with fully automatic micro processor based PLC with SCADA enabled reversible Drum Type mixer/ concrete Batch mix plant (Pan mixer) etc. complete. With fine aggregate (Crushed sand VSI Grade) Bd.F.6 Page One Number 300 and B.7, Page One Number38 One Cubic Metre 13932/-(SSR Item no 26.05 ,Pge no.) |
| 10 | 25.70 BDF 8 Providing and laying Cast in situ/Ready Mix cement concrete M-20 of trap/ granite / quartzite/ gneiss metal for R.C.C. slabs and landings as per detailed designs and drawings including steel centering, formwork, cover blocks, laying/pumping, compaction finishing the formed surfaces with cement mortar 1:3 of sufficient minimum thickness to give a smooth and even surface or roughening if special finish is to be provided and curing etc. complete,(Excluding reinforcement and structural steel).with fully automatic micro processor based PLC with SCADA enabled reversible Drum Type mixer/ concrete Batch mix plant (Pan mixer) etc. complete. With fine aggregate (Crushed sand VSI Grade) Bd.F.8 Page One Number 302 and B.7, Page One Number38 One Cubic Metre 13932/-(SSR Item no 25.70 ,Pge no.) |
| 11 | 26.33 BDF 17 Providing and fixing in position TMT - FE - 500 bar reinforcement of various diameters for R.C.C. pile caps, footings, foundations, slabs, beams columns, canopies, staircase, newels, chajjas, lintels pardis, copings, fins, arches etc. as per detailed designs, drawings and schedules. including cutting, bending, hooking the bars, binding with wires or tack welding and supporting as required complete. Bd.F.17, Page One Number 306 Metric Tonne 89703/-(SSR Item no 26.33 ,Pge no.) |
| 12 | 27.12 Providing fly ash brick masonry with conventional / I.S. type fly ash bricks in C.M. 1:6 infoundation and plinth including bailing out water manually striking joints, racking outjoints watering and scaffolding etc. complete(SSR Item no 27.12 ,Pge no.) |
| 13 | 27.13 Providing fly ash brick masonry with conventional/ I.S. type bricks in cement mortar 1:6 in superstructure including striking joints, raking out joints, watering andscaffolding etc. Complete(SSR Item no 27.13 ,Pge no.) |
| 14 | 24.16 Providing and laying Cast in situ/Ready Mix cement concrete M-15 of trap/ granite/quartzite/gneiss metal for coping to plinth or parapet, moulded or chamfered as per drawing or as directed including steel centering, plywood/ steel formwork compacting, roughening them if special finish is to be provided, finishing uneven and honeycombed surface and curing etc. complete. The Cement Mortar 1:3plaster is considered for rendering uneven and honeycombed surface only. Newly laid concrete shall be covered by gunny bag, plastic, tarpaulin etc. (Wooden centering will not be allowed.) With fine aggregate (Crushed sand VSI Grade)(SSR Item no 24.16 ,Pge no.) |
| 15 | 32.04Providing internal cement plaster 12mm thick in single coat in cement mortar 1:4without neeru finish to concrete or brick surfaces, in all positions including scaffoldingand curing etc. complete. (SSR Item no 32.04 ,Pge no.) |
| 16 | 31.01 Providing internal cement plaster 6 mm thick in a single coat in cement mortar 1:4without neeru finish to concrete surface in all positions including scaffolding and curingetc. complete. (SSR Item no 31.01 ,Pge no.) |
| 17 | 32.07 Providing internal cement plaster 20mm thick in Single coats in cement mortar 1:4 without neeru finish, to concrete, brick surface, in all positions including scaffolding and curing etc.complete.(SSR Item no 32.07,Pge no.) |
| 18 | 33.20 Providing sills of polished Kadappa stone 25mm to 30mm thick, on a bed of 1:4cement mortar including cement float, filling joints with slurry, curing polishing andcleaning etc. complete. (SSR Item no 33.20 ,Pge no.) |
| 19 | 33.40 BDM 12 Providing and laying vitrified mirror / glossy finish tiles decorative type having size 590 mm to 605 mm x 590 mm to 605 mm of 8 to 10 mm thickness and confirming to IS. 15622-2006 ( group Bla) of approved make, shade and pattern for flooring in required position laid on a bed of 1:4 cement mortar including neat cement float, filling joints, curing and clearing etc. complete. Bd.M. 12 Page One Number385 One Square Metre 1177/-(SSR Item no 33.40,Pge no.) |
| 20 | 33.41 BDM 12 Providing and laying vitrified mirror / glossy finish tiles having size 590 mm to 605 mm x 590 mm to 605 mm of 8 to 10 mm thickness and confirming to IS. 15622-2006 ( group Bla) of approved make, shade and pattern for dado and skirting in required position fixed in 1:4 cement mortar including neat cement float, filling joints, curing and clearing etc. complete Bd.M. 12 Page One Number385 One Square Metre 1252/-(SSR Item no 33.41,Pge no.) |
| 21 | 32.34 Providing and applying Two coats of wall care Putty on plastered surface and Ceilingand Walls to prepare surface even and smooth of approved make, etc complete. (SSR Item no 32.34,Pge no.) |
| 22 | 35.21 Providing and applying priming coat on concrete/masonary/ Asbestos Cement plastered surfaces includingscaffolding if necessary, preparing the surface bythoroughly cleaning oil, grease, dirt and other foreign matterand sand papering as required etc. complete.(SSR Item no 36.11,Pge no.) |
| 23 | 36.11 Providing and applying washable oil-bound distemper of approved colour and shade to old and new surfaces intwo coats including scaffolding, preparing the surfaces.(excluding the primer coat.) etc. complete(SSR Item no 33.41,Pge no.) |
| 24 | 35.13 Providing and applying two coats of water proof cementpaint of approved manufacture and of approved colour tothe plastered surfaces including scaffolding if necessary,cleaning and preparing the surface, watering for two daysetc. complete. (SSR Item no 35.13,Pge no.) |
| 25 | 39.01 Providing and fixing frame with / without ventilator of size asspecified with Country cut teak wood for doors and windowsincluding chamfering, rounding, rebating, iron holdfast ofsize 300mm x 40mm x 5mm with oil painting, etc. complete. (SSR Item no 39.01 ,Pge no.) |
| 26 | 39.09 Providing and fixing solid core flush door shutter in single leaf 32 mm thick decorative type of exterior grade as per detailed drawings approved face veneers 3 mm thick onboth faces or as directed, all necessary beads, mouldingsand lipping, wrought iron hold fasts, chromium platedfixtures and fastenings, with brass mortise lock,chromium plated handles on both sides, and finishingwith French Polish etc. complete. (SSR Item no 39.09,Pge no.) |
| 27 | 40.01 Providing and fixing mild steel grill work for windows,ventilators etc. 20 Kilogram/ One Square Metre as perdrawing including fixtures, necessary welding and paintingwith one coats of anticorrosive paint and two coats of oilpainting complete.(SSR Item no 40.01,Pge no.) |
| 28 | 39.44 Providing and fixing in position (as per 1868 / 1982)Aluminium sliding window of three tracks with rectangularpipe 95 x 38.10 x 0.90 mm at weight 0.637 Kilogram/OneRunning Metre. with window frame bottom tracksection 92 x 31.75 x 1.30 mm at weight 1.070Kilogram/One Running Metre.. Top and side track section92 x 31.75 x 1.30 mm at weight 0.933 Kilogram/Runningmetre. The shutter should be of bearing bottom 40 x18 x 1.25 mm at weight 0.417 Kilogram/One RunningMetre. Inter locking section 40 x 18 x 1.10 mm at weight0.469 Kilogram/Running metre. and handle and topsection 40 x 18 x 1.25 mm at weight 0.417Kilogram/Running metre. As per detailed drawingsand as directed by Engineerincharge with allnecessary Aluminium sections fixtures and fastenings suchas roller bearing in nylon casting and self locking catch fittedin vertical section of shutter including 5 mm thick plainglass and aluminium mosquito net shutter with stainlesssteel jail with all required screws and nuts etc, complete.With powder coating without box(SSR Item no 39.44,Pge no.) |
| 29 | 33.53 Providing and fixing heavy duty inter locking concreteRUBBER MOULD GLOSSY PAVING BLOCKS of 60millimeter thickness of having a strength of 400Kilogram/sq.m of approved quality and shape on a bed ofcrushed sand of 25 to 30 millimeter thick including strikingjoints and cleaning etc. complete. (using 100% crushedsand)(SSR Item no 33.53,Pge no.) |
| 30 | Providing and fixing Road junction / Information sign board of size 0.90 m x 0.60 m. prepared on 16 gauge M.S. sheet with angle iron frame of size 35x35x5 mm including painting with one coat of zinc cromate stoving primer and two coats each of green/ white back ground and back side gray stove enamelled, bonded with red retro reflective sheet Engineering grade, border / letters / numeral / arrows, coated with non pealable crystal clear protective coat retaining 100% reflection including two angle iron post of size 50x50x5 mm of 3.65 m. long inflated at bottom drilled on top and painted in white and black bands of 30 cm. with 4 Nos. high strength G.I. bolts and nuts of size 10 mm dia. and 20 mm long sheet and angle iron post in one piece without joints including all taxes, conveying, fixing in ground with cement concrete 1:4:8 block of 60 cm x 60 cm x 75 cm size as directed by Engineer-in-charge7814/- (S.S.R. It.no.6.47 Page No.60) Please Enable Macros to View BoQ information |
AI Tender Summary
Tender Timeline
Jul 13, 2026
11:30 IST
Tender Published
Tender notice published.
CompletedJul 27, 2026
17:00 IST
Bid Submission Deadline
Online submission via eProcurement portal.
Upcoming · 11 daysJul 28, 2026
Bid Opening Date
Technical bids will be opened and evaluated.
Upcoming · 12 daysTender Documents
Download All (ZIP) ↓
Disclaimer
We takes all possible care for accurate & authentic tender information. However users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender