Tender For Repair And Maintenance Of Street Lights, Lt Cables, Pole Box Assembly, Timer Panels At Kabul Line, Baird Place, Kotwali Line, Cedz Office, Cda (Army) And Associated Area Under Age (Sldc) E/S Under Ge (U) Electric Supply Delhi Cantt - 10
Tender Value
48 Lakhs
Estimated cost
Bid Submission
01 Aug 2026
17 days left
EMD
96000
Bank guarantee accepted
Document Fee
500
Non-refundable
Tender Type
Online
Tender Overview
Organization
Tender ID
Competition Type
NCB
Bidding Type
Tender
Location / State
New Delhi → Delhi
EMD Exemption
Available
Quantity
Not Available
Website
Contact Person
Address
Project Description
Tender for Repair And Maintenance Of Street Lights, Lt Cables, Pole Box Assembly, Timer Panels At Kabul Line, Baird Place, Kotwali Line, Cedz Office, Cda (Army) And Associated Area Under Age (Sldc) E/S Under Ge (U) Electric Supply Delhi Cantt - 10
BOQ
| Sl. No. | Item Description |
| 1 | Material and labour for excavation in trenches not exceeding 1.5 meter wide and not exceeding 1.5 meter in depth and getting out in soft/loose soil for foundation of poles, stays, laying of cables, etc complete all as specified and directed by Engineer-in-Charge. |
| 2 | Material and labour for returning filling including spreading, levelling watering and well ramming in layers not exceeding 25 cm thick in hard/dense soil complete all as specified and directed by Engineer-in-Charge. |
| 3 | Material and labour for removing excavated surplus hard/dense soil to a distance not exceeding 50 m and depsoiting where directed at a level not exceeding 1.5 m above the starting point complete all as specified and directed by Engineer-in-Charge. |
| 4 | Material and labour for river washed and screened, dry sand for filling in trenches below and around underground cables and in substation ducts for cushioning of cables etc, complete all as specified and directed by Engineer-in-Charge.NOTE :- Measurement should be taken after punning down |
| 5 | Supply & fixing of sub class B bricks having minimum compressive strength 75 Kg/ Sq cm laid in trenches for cable protection etc complete all as specified and directed by Engineer-in-Charge. |
| 6 | Dismantling concrete poles/ struts incl any size complete all as specified and directed by Engineer-in-Charge. |
| 7 | Re-fixing only of LED Street light retrived from item No-6 complete all as specified and directed by Engineer-in-Charge. |
| 8 | Re-fixing only of KIOSK Box retrived from item No-6 complete all as specified and directed by Engineer-in-Charge. |
| 9 | Supply and laying or fixing or passing through pipe, 1100 volts grade heavy duty cable with PVC insulated aluminium conductor served with an inner sheathing of PVC tape armoured with galvanised steel wire or tape and overall PVC sheathed 6 sq. mm 2 core nominal cross section in service connections complete all as specified and directed by Engineer-in-Charge after removing the old/damage cable. |
| 10 | Supply and laying of XLPE insulated heavy duty electric, un armoured cables 16 sqmm 4 core with aluminium conductor, 1100 volts grade for necessary connection with suitable lugs & fixing arrangement with necessary clamps & cable glands etc complete all as specified and directed by Engineer-in-Charge after removing the old/damaged cable. |
| 11 | Supply & fixing in replacement KIOSK Box weather proof made up of one piece mounted on SMC base and door pole mounted hinged door of size 333 x233x 120 mm outside and 300 x 200 x105 mm inside dimension comprising of aluminum bus bar 4 strips for 3 phase and neutral 63 Amp and 6 Amp fuse grip with base for controlling the steet light fitting and FL clamps 30x4mm with necessary MS nuts bolts and washers and including applying two coasts of synthetic enamel paint over a coat of red oxide zinc chrome primer on new steel surface and including embassing/painting of Danger notice of size not less than 10 cm x 7.5cm with letters, figures and conventional skull and bones in signal red colour on front face of KIOSK box body complete all as specified and directed by Engineer-in-Charge. |
| 12 | Material and labour for boring of hole under road/pavement/hard standing or any other situation by manual means and suitable for passing of GI pipe 100 mm bore and making good both ends complete all as specified and directed by Engineer-in-Charge. |
| 13 | Supply and fixing of 40 mm dia galvanized iron mild steel tubing, light grade including all fitting for cable protection etc laid in floor or fixed to poles with clamps etc complete all as specified and directed by Engineer-in-Charge. |
| 14 | Supply and fixing in replacement of LED street light fitting of 60 watt 230 V AC outdoor type with high pressure die cast aluminium hosing and heat resistant complete with driver, lamp bracket with impact and corrosion resistant including thermal management in multiple optics complete with IP65/66 protection complete all as specified and directed by Engineer-in-Charge. |
| 15 | Supply and fixing in replacement of LED street light fitting of 90 watt 230 V AC outdoor type with high pressure die cast aluminium hosing and heat resistant complete with driver, lamp bracket with impact and corrosion resistant including thermal management in multiple optics complete with IP65/66 protection complete all as specified and directed by Engineer-in-Charge. |
| 16 | Supply and fixing of New Generation Energy saving LED flood light of 100 watt power coated PDC aluminium body with toughened glass visor. Equipped with secondary optical PC lence Efficacy >110 Lm/w. Available in 5700K CCT, IP66 complete all as specified and directed by Engineer-in-Charge. |
| 17 | Supply and fixing New Generation Energy saving LED flood light of 120 watt power coated PDC aluminium body with toughened glass visor. Equipped with secondary optical PC lence Efficacy >110 Lm/w. Available in 5700K CCT, IP66 complete all as specified and directed by Engineer-in-Charge. |
| 18 | Supply & Fixing of LED Post Top Lantern warm white Fitting of 40 Watt, IP-65 protection ,energy saving, long life aesthetically designed with good indirect symmetrical light distribution, single piece pressure die cast aluminium landscape luminaire with high power COB LED as light source, 220 volt, 50 Hz, high grade powder coated finish with high voltage surge protection & other safety test as per IS 15885, with electronic driver, bolts,nuts & washers and suitable for pole complete all as specified and directed by Engineer-in-Charge. |
| 19 | Supply & Fixing of LED Post Top Lantern Fitting of 35 Watt, IP-65 protection ,energy saving, long life aesthetically designed with good indirect symmetrical light distribution, single piece pressure die cast aluminium landscape luminaire with high power COB LED as light source, 220 volt, 50 Hz, high grade powder coated finish with high voltage surge protection & other safety test as per IS 15885, with electronic driver, bolts,nuts & washers and suitable for pole complete all as specified and directed by Engineer-in-Charge. |
| 20 | Material and labour for bracket made out of GI pipe 40 mm dia medium grade, 1.2 meter long bent to shape fixed with MS flat irom clamps made out of 40mm x 6 mm thick, nuts bolts complete all as specified and directed by Engineer-in-Charge. |
| 21 | Supply and fixing in renewal of 3 pole power contactor ML-6 mounted on any type / description LT panel/feeder pillar/wall after taking down old existing un serviceable contactor complete all as specified and directed by Engineer-in-Charge. |
| 22 | Supply and fixing in renewal of 3 pole power contactor MNX-110 mounted on any type / description LT panel/feeder pillar/wall after taking down old existing un serviceable contactor complete all as specified and directed by Engineer-in-Charge. |
| 23 | Supply and fixing in renewal of Analog Time switch, 240 Volt AC, 50 Hz, mounted on any type / description LT panel/feeder pillar/wall after taking down old existing un serviceable time switch complete all as specified and directed by Engineer-in-Charge. |
| 24 | Taking down of unsv street light from street light pole and material and labour for fixing in replacement of Driver suitable for LED Street light 45-60 watt, any make complete all as specified and directed by Engr In charge. |
| 25 | Supplying and installation of factory made and tested (including CPRI type tested certified panel) Timer panel board, cubical, outdoor type, platform mounted, suitable for 415 volts, 3 phase, 4 wire, 50 Hz AC supply system. The panel shall be dust and vermin proof IP-65 class protection and shell be made of 3.15 mm CRCA MS Sheet, and minimum 32x32x5 mm thick MS angle iron frame work, powder coated finis over one coat of red oxide primer on outside surface and paonted inside with two coats of red oxide primer, front opening type, closing locking arrengment including power wiring with 10 Sqmm PVC insulated solid, copper conductor and comprising of the following :- (i) MCCB 3 pole, 32 Amps, 50 Hz,415 Volts, 10 KA, with thermal magenetic release - 01 No. (ii) 3 pole power contractor, type MNX 110 having 2 NO + 2 NC contact - 01 No. (iii) Analog Time switch, 240 volts, AC, 50 Hz - 01 No. (iv) Auto/manual selector switch - 01 No. (v) Aluminium bus bar 100 Amps, 4 strip 3 phase and neutral 415 volts, 50 Hz, duly insulated with heat shrinkable PVC sleeves - 01 Set. Platform for the timer panel with PCC 1:4:8 type D-2 with 40 mm graded crushed stone, 15 cm thick in foundation, brick work in CM 1 : 6 with sub class 'B' old size bricks, rendering 15 mm thick in CM 1 : 6 on exposed surfaces and 100 mm thick PCC padding 1:3:6, type C-1 using 20 mm graded crushed stone aggregate on top and grouting bolts etc for panel. The platform shall be such that it is of a height 45 cm above the nearest road level. |
| 26 | Supply, installation, testing and commissioning in replacement of factory made tested LT panel board of size not less than 1.4 mtr x 0.55 mtr x 1.6 mtr cubical double door compartment outdoor type leg mounted suitable for 415 volts 3 phase, 4 wire, 50 HZ AC supply system having bus bar chamber with insulated Aluminium bus bar of rating not less than 1.5 times of Incomer/ Outgoings MCCBs, installed on proceline/ SMC insulator. The panel shall be dust and vermin proof IP -65 class protection and made of 3.15 mm CRCA MS sheet and inner compartment 2.0 mm, 40X40X6 mm thick MS angle iron frame work, fixing of double doors shall be on MS hinges with anti-theft provision (the door can’t be removed from enclosure without cutting enclosure), powder coated finished over one coat of red oxide on out side surface and painted in side with two coats of red oxide primer and rear opening type with apran for cable entery closing locking arrangement including internal wiring with PVC insulated multisranded copper conductor FRLS cable IS 694 marked , 1100 volts grade of appropriate size (but not less than 2.5 sqmm) and comprising of the following including necessary brick work for platform of suitable size:- INCOMING:- (i) MCCB 4 pole, 400 Amps Thermal Magnetic and Adjustable type, 50 Hz, 415 Volts, 36 KA -1 No OUTGOINGS:- (i) MCCB 4 pole, 320 Amps, 50 Hz, 415 Volts, 25KA Adjustable Thermal and Adjustable Magnetic setting- 04 Nos (ii) MCCB 4 pole, 160 Amps, 50 Hz, 415 Volts, 25KA Adjustable Thermal and Adjustable Magnetic setting- 04 Nos (ii) Digital Voltmeter 0-500 V-01 No with selector switch (iii) Digital Ammeter with selector switch 300 Amps including suitable CT-01 Set (iv) LED Indicator lamp-1 set (1) Panel wiring complete with copper cable of suitable rating and size. |
| 27 | Material and labour for prunning/trimming the branches of trees if any along LT overhead line/ street light pole, 3 mtr on all side below/above/sides of LT overhead line and removing the same upto 150 mtr away each span not exceeding 50 mtr complete all as specified and directed by Engineer-in-Charge (NOTE :- The above is to be ensured for the entire contract period by cutting/trimming of trees any number of times as required). |
| 28 | Material and labour for preparation of old painted surfaces of Steel tubular LT poles, any height including cross arms, MS strap, nuts, bolts, washers, cable protection pipe wherever provided etc and painting of complete poles with one coat of aluminium paint from 2.1 m above ground level to top of pole including cross arms and protection pipe and painting of bottom area of pole upto 2.1 m from ground level with synthetic enamel paint in alternate layer (30 cm wide) with black and yellow paint including writing pole numbers in white letter of approved size on black ground complete all as specified and directed by Engineer-in-Charge. |
| 29 | Material and labour for preparation of old painted surfaces of LT PCC poles for cross arms, MS strap, nuts, bolts, washers, cable protection pipe wherever provided etc and painting with one coat of aluminium paint and painting of bottom area of pole upto 2.1 m from ground level with synthetic enamel paint in alternate layer (30 cm wide) with black and yellow paint including writing pole numbers in white letter of approved size on black ground complete all as specified and directed by Engineer-in-Charge. |
| 30 | Supply and fixing of steel tubular swaged poles type 410 SP-31 (9.0 meter long) Swan Neck Type complete with CI base plate and finial and single swan neck, including painting of complete poles with two coat of aluminium paint from 2.1 m above ground level to top of pole and painting of bottom area of pole upto 2.1 m from ground level with synthetic enamel paint in alternate layer (30 cm wide) with black and yellow paint including protection pipe over a coat of red oxide zinc chrome primer on new steel surface, complete all as specified and directed by Engineer-in-Charge |
| 31 | Supply & Fixing of 3 Mtr long decorative, 02 Nos bracket Pole aesthetically designed decorative hot dipped galvanised mild steel step pole with grey powder finish, Compatible for all Havells/ Bajaj/ Crompton post top range. Window-plasma out cut & duly chamfered opening window of 300 X 110 mm for treminal connection & mounting accessories. Window cover is fitted with allen screws to the pole. Decorative sleek casting ring to increase aesthetical appeal with bolts,nuts & washers including earth work and RCC foundation as per height of light all as specified and directed by Engr-in-charge. |
| 32 | Material and labour for plain cement concrete type D2, 1:4:8 (using 40 mm graded crushed trap stone aggregate) in foundations, filling and mass concrete complete all as specified and directed by Engineer-in-Charge. |
| 33 | Material and labour for plain cement concrete type B1, 1:2:4 (20 mm graded crushed trap stone aggregate) in coping and the like including weathering, slightly rounded or chamfered angles and throating as directed with and including use of form work complete all as specified and directed by Engineer-in-Charge |
| 34 | Material and labour for cement concrete type B-1, 1:2:4, 50 mm thick (using 20 mm gradded aggregate) for floors and paving etc complete all as specified and directed by Engineer-in-Charge |
| 35 | Material and labour for painting of timer panel boards out door/in door of size above 5.00 Sqmm floor/leg mounted installed at different locations including preparation of exposed surface by removing old paint from the body, cleaning the surface with thinner and applying two coats of synthetic enamelled smoke grey paint including repair of panel door's nut & bolts/hinges etc for smooth functioning to open and clsoe of doors complete all as specified and directed by Engineer-in-Charge. Please Enable Macros to View BoQ information |
| 36 | Material and labour for painting of timer panel boards out door/in door of size above 5.00 Sqmm floor/leg mounted installed at different locations including preparation of exposed surface by removing old paint from the body, cleaning the surface with thinner and applying two coats of synthetic enamelled smoke grey paint including repair of panel door's nut & bolts/hinges etc for smooth functioning to open and clsoe of doors complete all as specified and directed by Engineer-in-Charge. Please Enable Macros to View BoQ information |
AI Tender Summary
Tender Timeline
Jul 11, 2026
11:30 IST
Tender Published
Tender notice published.
CompletedAug 01, 2026
17:00 IST
Bid Submission Deadline
Online submission via eProcurement portal.
Upcoming · 17 daysAug 03, 2026
Bid Opening Date
Technical bids will be opened and evaluated.
Upcoming · 19 daysTender Documents
Download All (ZIP) ↓
Disclaimer
We takes all possible care for accurate & authentic tender information. However users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender