Tender For Welcome Maintenance To Offrs Md Accn And Repair/Maint Work In Jco/Or Md Accn At Af Stn Under Ge Brichgunj, Sri Vijaya Puram
Tender Value
25 Lakhs
Estimated cost
Bid Submission
04 Aug 2026
3 days left
EMD
50000
Bank guarantee accepted
Document Fee
500
Non-refundable
Tender Type
Online
Tender Overview
Organization
Tender ID
Competition Type
NCB
Bidding Type
Tender
Location / State
South Andamans → Andaman And Nicobar Islands
EMD Exemption
Available
Quantity
Not Available
Website
Contact Person
Address
Project Description
Tender for Welcome Maintenance To Offrs Md Accn And Repair/Maint Work In Jco/Or Md Accn At Af Stn Under Ge Brichgunj, Sri Vijaya Puram
BOQ
| Sl. No. | Item Description |
| 1 | Taking down cement plaster on Brick / Concrete surfaces incl raking out joints, hacking for key scrubbing down with water complete all as specified and as directed. |
| 2 | Demolition of PCC Block walling built in CM 1:6 complete all as specified and as directed |
| 3 | M&L for Precast cement concrete block masonry with PCC solid blocks in 1:3:6 type C1 using 20mm graded stone aggregates, exc. 10cm in width and set in CM 1:4 complete all as specified and as directed. |
| 4 | M&L for Rendering 10 mm thick on fair faces of brick work or concrete surfaces in cement mortar 1:6 finished even and smooth without using extra cement complete all as specified and as directed. |
| 5 | M&L for Rendering 15mm thick in two layers of 10mm thick backing coat in CM 1:6 and 5mm thick floating coat in CM 1:4 mixed with water proofing compound on all external wall surfaces finished even and smooth without using extra cement complete all as specified and as directed. (Note : Water proofing compound shall be measured and paid seperately) |
| 6 | M&L for Rendering 5 mm thick on fair faces of brick work or concrete surfaces as in Ceiling Surface, soffits of slab/chhajas in cement mortar 1:3 finished even and smooth without using extra cement complete all as specified and as directed. |
| 7 | Supply only liquid integral water proofing chemicals complete all as specified and directed. |
| 8 | M&L for Two coats of oil bound distemper on new plastered surfaces wall over a coats of alkali resistant priming paint including preparation of new plastered or unplastered surfaces of wall complete all as specified and as directed by Engineer - in -Charge. |
| 9 | M & L for Two coat of wheather proof exterior acrylic emulsion paint with anti fungal property on newly plastered wall surfaces including preperation of surfaces over a coat of primer complete all as specified and as directed. |
| 10 | M&L for Prepration of new ceiling surfaces and applying 3 coat of white wash on ceiling complete all as specified and as directed. |
| 11 | M& L for Applying 1mm thick on wall care putty on wall complete all as specified and as directed. |
| 12 | M&L for Preparation of old plastered or unplastered surfaces of walls and applying two coat of oil bound distemper complete all as specified and directed by Engineer - in -Charge. |
| 13 | M&L for Preparation of old plastered or unplastered surfaces of ceiling and applying two coat of oil bound distemper complete all as specified and directed by Engineer - in -Charge. |
| 14 | M&L for Preparation of old external surfaces of walls, Facias, cornices etc and applying two coat of weather proof anti fungal paint (Apex - ultima) on walls all as per manufacturer instruction including necessary scaffolding complete all as specified and directed by Engineer-in-Charge. |
| 15 | M&L for Preperation of old painted steel surfaces over 10 cm in width or girth applying two coat of synthetic enamel paint over a coat of anti-corrosive paint complete all as specified and directed. |
| 16 | M&L for preperation of old painted wood and wood based suraces over 10 cm in width or girth applying one coat of synthetic enamel paint over a coat of pink primer complete all as specified and directed. |
| 17 | Taking down of chowkhats or frames not exc 1.5 sqm each (without taking off shutters from the frame) complete all as specified and as directed. |
| 18 | All as per item No above but exc 1.5 sqm but n exc 4 sqm each complete all as specified and as directed. |
| 19 | S&F Solid PVC Door Frame of size 50mm x 47mm made out of 5mm plain colour PVC sheet reinforced with M.S Square tube, supplying & fixing in opening as per specification & drawing complete all as specified and as directed. |
| 20 | S&F Factory made solid panel PVC door shutter 30mm thick (style) consisting of frame made out of M.S. tubes for top & bottom rails, M.S. frame shall be covered with heat moulded plain colour PVC `C' channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail; Panelling of plain colour PVC sheet to be fitted in the M.S frame welded/ sealed to the stiles, & rails with suitable PVC sheet beading, and joined together with solvent cement, supplying & fixing in the frame at site as per specification & drawing complete all as specified and as directed. |
| 21 | S & F Anodised aluminium frame for doors, windows, ventilators with one or more rebates including joining cleat for fixing etc. complete all as specified and as directions of Engineer-in-charge. |
| 22 | S & F Powder coated aluminium (minimum thickness of powder coating 50 micron) work for doors, windows, ventilators and partitions (Fixed portions) with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS:1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing/ paneling, C.P. brass/ stainless steel screws, all complete as per architectural drawings and the directions of Engineer-in-Charge. |
| 23 | S&F Powder coated aluminium (minimum thickness of powder coating 50 micron) for shutters of doors, windows & ventilators including providing and fixing hinges/ pivots and making provision for fixing of fittings wherever required including the cost of EPDM rubber/neoprene gasket required (Fittings shall be paid for separately) with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS:1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing/ paneling, C.P. brass/ stainless steel screws all complete as per architectural drawings and the directions of Engineer-in-charge. |
| 24 | M&L for Aluminium grill (anodised transparent or dyed to required shade according to IS: 1868 with minimum anodic coating of grade AC 15) of approved design/pattern, with approved standard section and fixed to the existing window frame with C.P. brass/ stainless steel screws @ 200 mm centre to centre, including cutting the grill to proper opening size for fixing and operation of handles and fixing approved anodised aluminium standard section around the opening, all complete as per requirement and direction of Engineer in-charge |
| 25 | M & L for Complete removal of old plastered surfaces of walls and applying Two or more coatsof 100% Premium acrylic emulsion paint having VOCC less than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance,dirt resistance exterior paint of required shade(Company Depot Tinted) with silicon additives @ 1.43 litre/ 10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/ 10 sqm complete all as specified and as directed. |
| 26 | S&F Factory made single extruded WPC (Wood Polymer Composite) solid door/ window/ Ceosetory windows & other Frames/ Chowkhat of size 50x 100 mm comprising of virgin PVC polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/ wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) fabricated with miter joints after applying PVC solvent cement and screwed with full body threaded star headed SS screws having minimum frame density of 750 kg/ cum, screw withdrawal strength of 2200 N (Face) & 1100 N (Edge), minimum compressive strength of 58 N/mm2, modules of elasticity 900 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/ moisture proof and fire retardant and fixed in position with MS hold fast/ lugs/SS dash fasteners of required dia and length complete as per direction of Engineer-in-Charge. (M.S. hold fast/ lugs or SS dash fasteners shall be paid for separately). ® Note: For WPC solid door/window frames, minus 5mm tolerance in dimension i.e. depth and width of profile shall be acceptable. Variation in profile dimensions on plus side shall be acceptable but no extra payment on this account shall be made complete all as specified and as directed. |
| 27 | S&F Factory made single extruded WPC (Wood Polymer Composite) solid door/ window/ Ceosetory windows & other Frames/ Chowkhat of size 65x 125 mm comprising of virgin PVC polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/ wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) fabricated with miter joints after applying PVC solvent cement and screwed with full body threaded star headed SS screws having minimum frame density of 750 kg/ cum, screw withdrawal strength of 2200 N (Face) & 1100 N (Edge), minimum compressive strength of 58 N/mm2, modules of elasticity 900 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/ moisture proof and fire retardant and fixed in position with MS hold fast/ lugs/SS dash fasteners of required dia and length complete as per direction of Engineer-in-Charge. (M.S. hold fast/ lugs or SS dash fasteners shall be paid for separately). ® Note: For WPC solid door/window frames, minus 5mm tolerance in dimension i.e. depth and width of profile shall be acceptable. Variation in profile dimensions on plus side shall be acceptable but no extra payment on this account shall be made complete all as specified and as directred. |
| 28 | S&F Factory made single extruded WPC (Wood Polymer Composite) solid plain flush door shutter of 30mm size comprising of virgin polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) having minimum density of 650 kg/cum and screw withdrawal strength of 1800 N (Face) & 900 N (Edge), minimum compressive strength 50 N/mm2, modulus of elasticity 850 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/moisture proof and fire retardant. WPC to be laminated with PVC foil of minimum 14 microns thick of approved design pasted with hot melt adhesive on both faces of shutter and fixing with stainless steel butt hinges of required size with necessary full body threaded star headed counter sunk S.S screws, all as per direction of Engineer- In- Charge. (Note: stainless steel butt hinges and necessary S.S screws shall be paid separately) |
| 29 | Providing and fixing factory made uPVC Frames (60mm x 58mm) white colour casement/sliding window/door, made of extruded profiles. Profiles of frames and sash will be mitered cut and fusion welded at all corners, including drilling of holes for fixing hardware and drainage of water etc.. making arrangement for fixing of hardware, EPDM gasket, 1.2+ 0.2.mm thick galvanized steel profile to be inserted in required profile, frame will be fixed to the wall with 8mm x 100mm long fasteners, complete all as specified and as directed, (Glazing, hardware hinges and fitting, EPDM rubber gasketetc. to be paid separately.) |
| 30 | Providing and fixing factory made uPVC white colour casement (Openable) window made of extruded profiles with wall thickness of 2.3mm ( + – 0.2mm). Window profile with hollow section with multi chamber, frame (60mm x 58mm), sash (60mm x 73mm), T profile (One vertical length in between two shutters) (60mm x 74mm), Glazing bead (35mm x 20mm) will be mitered cut and fusion welded at all corners, including drilling of holes for fixing hardware and drainage of water etc., making arrangement for fixing of hardware. EPDM gasket 1.2 +– 0.2mm thick, galvanized steel Frame (28mm x 21.5mm), sash (31mm x 27.5mm). T profile (27mm x 17mm) to be inserted in required profile, frame will be fixed to the wall with 8 mm x 100mm long fasteners. Hardware: [casement handle made of zinc alloyed (white powder coated), But Hinges of'zinc alloyed (white powder coated), transmission gear made of mild steel with multi point locking system] and 5mm thick glazing with selected quality glass complete all as specified and as directed. (Note: The unit rate quoted by contractor excludes cost of glass and includes all other connected accessories. Net opening will be measured for payment purpose.) (a) Area exceeding 1.00 Sqm but not exceeding 2.00 Sqm Each |
| 31 | (b) All as per Ser Item No.30 above but Area exceeding 2.00 Sqm Each |
| 32 | Providing and fixing factory made uPVC white colour casement (Openable) Door made of extruded profile wilh wall thickness of 2.3mm ( + -0.2mm). Window profile with hollow section with mitlti chamber, frame (60mm x 58mm), sash (60mm x 78mm). T profile (One vertical length in between two shutters) (60mm x 74mm). Glazing bead (35mm x 20mm) will be mitered cut and fusion welded at all corners, including drilling ol holes for fixing hardware and drainage of water etc., making arrangement for fixing of hardware. EPDM gasket 1.2 + -0.2mm thick galvanized steel Frame (28mm x 21.5mm), sash (31mm x 27mm), T profile (27mm x 17mm) to be inserted in required profile, frame will be fixed to the wall wilh 8mm x 100mm long fasteners. Hardware: [casement door handle made of zinc alloyed (white powder coated). Corner striker. Secondary Strikers. Cylinder. Door transmission gear made of mild sleel with multi point locking system with strikes. 3D Hinges of zinc alloyed (white powder coated) [and 5mm thick glazing with selected quality glass. (Note: The unit rate quoted by contractor excludes cost of glass and includes all other connected accessories complete all as specified and as directed. Net opening will be measured for payment purpose.) |
| 33 | M&L for MDF/HDHMR board, 16 mm thick of any Colour to fixed with screws to timber frame work or Fixed wirh aluminiun frame work to the fixing Clips complete all as specified and as directed (Note :- Colour as finalised by GE) |
| 34 | S&F Aluminium composite panel sheet of 3mm to 4mm thick, fixed on aluminium frame work with plastic strips (double sided sticker) of suitable size of varying thickness of 10mm to 30mm applying adhesive over aluminium sections for fixing composite panel and fixed with screws. The joints of panels shall be filled with weather proof sealant for required portion, complete all as specified and as directed. |
| 35 | S&F in Repairs Aluminium (extruded section ) Door closer hydraulically regulated, designation No. 3 universal type, suitable for door shutters of 851 to 1000 mm in width and of weight between 61 to 80 kg and fixed complete all as specified and as directed. |
| 36 | S & F in Repairs aluminium alloy, anodised, sliding door bolt with hasp & staple (Bolt type) 300mm long and fixing clips of sheet, cast or extruded section and fixing bolt of cast aluminium alloy, complete all as specified and as directed by Engineer-in-charge. |
| 37 | S & F in Repairs aluminium, anodised, barrel tower bolt of extruded section, 150 mm long, complete all as specified and as directed by Engineer-in-charge. |
| 38 | S & F in Repairs aluminium alloy anodised handle, 150 mm long extruded, fabricated type, complete all as specified and as directed by Engineer-in-charge. |
| 39 | S&F Butt hinges of size 100 mm medium weight cold rolled mild steel complete all as specified and as directed. |
| 40 | S&F in Repairs aluminium alloy wire mesh 0.45mm nominal dia of wire and average width of apeture 1.4mm fixed with aluminium wire staples etc.complete all as specified and as directed. |
| 41 | S&F Sheet glass 4.0mm thick, ordinary quality and glazing with oil putty in Square n.exc 0.5 sqm in each pane complete all as specified and as directed |
| 42 | S&F Sheet glass 4.0mm thick, ordinary quality and glazing with oil putty in Square exc 0.5 sqm in each pane complete all as specified and as directed |
| 43 | S&F in repair 140mm Floor door stopper of aluminium alloy body and tongue, anodised, with hard drawn steel spring, fixed in floor complete all as specified and as directed. |
| 44 | S&F in Repairs Harrison rails, mild steel, chromium plated Curtain Rails with fixing brackets, stops, rollers etc complete all as specified and as directed. |
| 45 | Dismantling wrought iron or mild steel work of any description not otherwise provided for complete all as specified and as directed. |
| 46 | Dismantling for plain or corrugated roof sheeting of any description, any gauge, thickness, including Removing L-type or J-type bolts in Roof Covering complete all as specified and as directed. |
| 47 | S & F MS Steel work in tubular trusses and tubular posts/ purlins including special shaped washers etc., complete using ERW or induction butt welded tubes conforming to IS :1161-1979 grade st-240 including notching, drilling, fitting, riveting and/or welding or connecting with bed plate, bolt and nuts complete all as specified and as directed. |
| 48 | S & F Plates (Plain or chequered), channels, square cut or notched (ordinary and counter sunk) forming holes with attachment etc and fixed by riveting or welding or with nut and bolts (including nut and bolts) conforming to Fe- 410-W Grade E- 250, quality B, complete all as specified and as directed. |
| 49 | M&L for Preparing new steel surfaces of any description over 10cm width or girth and applying two coats of synthetic enamel paint over a coat of red oxide primer on steel surfaces complete all as specified and as directed. |
| 50 | S&F Pre-painted galvalume aluminium zinc coating GI based (corrugated/semi corrugated) sheet 0.50mm thick as per approved profile, coloured, having tensile strength of 550Mpa as in roof covering/cladding to wall, fixed with self tapping screwscomplete all as specified and as directed. |
| 51 | S&F Pre-painted galvalume aluminium zinc coating GI based plain steel sheet 0.50mm of an colour having tensile strength of 550Mpa as in roof covering/cladding to wall, fixed with self tapping screws complete all as specified and as directed. |
| 52 | S&F Plain, Aluminium sheeting, 0.56mm thick Alloy 31000 H4 in ridges, hips, valley gutter, drip and straight flashing (length and girth as fixed) fixed with self tapping screws as specified complete all as specified and as directed. |
| 53 | Dismantling of Wall and ceiling boards (fibre, pulp, insulation, etc.) or insulation boards/slabs/blankets, any thickness, including cover fillets Including frame of any description and any thickness, fixed in any position complete all as specified and as directed. |
| 54 | Material and labour for false ceiling with aluminum grid work (Size of grid 605x605 mm) with 35 x 25 x 1.5 mm main tee and 25 x 25 x 1.4 mm cross tee and wall angle and suspended with 2mm dia GI wire hooked to roof with needful adjustment bolts at an interval of 1.20 m centre to centre staggered and board with Eco board decorative type size 600 x 600 x 4 mm thick complete all as specified and as directed |
| 55 | S&F Gl frame work for seamless ceiling comprising of Gl perimeter channnel 0.55 mm thick with two unequal flanges of 20 and 30 mm and web of 27 mm fixed to surrounding wall using nylon sleeves and screws at 450 mm centre to centre/intermediate channel 0.9 mm thick having two equal flanges of 15 mm each and web of 45 mm suspended from soffit at approx 900 mm centre to centre with Gl cleat and steel expansion fasteners with and including ceiling section (not exc 1.2 m length) of 0.55 mm thickness having kurled web of 50 mm and flange of 26 mm each with lips of 10.5 mm fixed to the intermediate channel with connecting clips across the intermediate channel at 457 mm centre to centre complete all as specified and as directed. |
| 56 | S&F Hangers 6mm dia G.I. (upto 1200mm length) adjusting level fixed to roof slabs by means of ceiling cleats made out of GI Flat 40x3mm size 60mm long and expansion hold fasteners 12.5mm dia 40mm long complete all as specifeid and as directed. |
| 57 | S&F PVC insulation panels of 10mm thick with EPS stuck to 1mm printed PVC Sheet suitably placed in false ceiling grid made of Aluminium/GI/MS as per specification complete all as specified and as directed |
| 58 | Material and labour for providing and fixing stainless steel (Grade 304) railing made of hollow tubes, channels ,plates etc, including welding,grinding, buffing, polishing and making curvature (wherever required) and fitting the same with necessary stainless steel nuts and bolts complete, including fixing the railing with necessary accessories & stainless steel dash fasteners, stainless steel bolts etc of required size, on the to of floor or the side of waist slabwith suitable arrangement complete all as specified and as directed. |
| 59 | Demolition of stone slab and tiles of any description or thickness in floors, aprons etc laid bedded and pointed in any mortar complete all as specifed and as directed. |
| 60 | Dismantling any type of Floor or Wall tiling including cement mortar bedding (but not backing) and Removing Rubbish out side of the MD Land complete all as specified and as directed by Engineer-in-Charge. |
| 61 | M&L for Cement concrete type B-1 (20 mm graded stone aggregate), 25mm thick as in level coarse complete all as specified and as directed. |
| 62 | M&L for Virified Ceramic tiles 10 mm thick (square/ rectangular) light shade polished, area of each tiles not exceeding 0.36 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match over screed bed or bedding layer of mortar 15 mm thick in Cement mortor 1:6 for laying floor finishes complete all as specified and as directed. |
| 63 | M&L for Virified Ceramic tiles 10 mm thick (square/ rectangular) light shade polished, area of each tiles not exceeding 0.36 sqm, in skirting etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match over screed bed or bedding layer of mortar 10 mm thick in Cement mortor 1:4 for laying floor finishes complete all as specified and as directed. |
| 64 | M&L for Virified Ceramic tiles 10 mm thick (square/ rectangular) light shade polished, area of each tiles exceeding 0.42 sqm but n exc 1.00 Sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match over screed bed or bedding layer of mortar 15 mm thick in Cement mortor 1:6 for laying floor finishes complete all as specified and as directed. |
| 65 | M&L for Virified Ceramic tiles 10 mm thick (square/ rectangular) light shade polished, area of each tiles exceeding 0.42 sqm but n exc 1.00 Sqm, in skirting/Dado etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match over screed bed or bedding layer of mortar 10 mm thick in Cement mortor 1:4 for laying floor finishes complete all as specified and as directed. |
| 66 | M&L for Coloured non skid ceramic tiles 7 to 8mm thick (square/rectangular) area of each tile exc 0.06 sqm n.exc 0.11 sqm, in floors etc set and jointed in neat cement slurry and pointed with coloured cement to match the colour of tiles over and including screed bed or bedding layer of mortar 15 mm thick in CM 1:4 for laying floor finishes complete all as specified and as directed. |
| 67 | M&L for Glazed ceramic coloured / printed tiles (450X300mm) x 6-7mm thick on vertical surfaces as in skirting/dado, set and jointed with neat cement slurry and pointed in white/coloured cement to match the shade of tiles over 10mm thick rendering in cement mortar 1:3. complete all as specified and as directed. |
| 68 | M&L for Granite (of any type) tiles 20mm thick machine cut, bedded and jointed with grey cement slurry and pointed with white cement with admixture of pigment to match the shade of granite stone including grinding and polishing complete over Screed bed or bedding layer of mortar 15 mm thick in cm 1:6 for laying floor finishes all as specified and as directed. |
| 69 | M&L for Granite (of any type) tiles 20mm thick machine cut, in skirting/ dado laid over cement screed and jointed with grey cement slurry, and pointed with white cement with admixture of pigment to match the shade of granite stone including grinding and polishing complete laid over 10mm thick cement plaster in cement mortar 1:4 complete all as specified and as directed. |
| 70 | Taking up or down, 20mm dia bore, GI tubing, medium grade, including cleaning for refixing or removing from site, complete all as specified and as directed by Engineer-in-Charge. |
| 71 | Taking up or down, 25mm dia bore, GI tubing, medium grade, including cleaning for refixing or removing from site, complete all as specified and as directed by Engineer-in-Charge. |
| 72 | Supplying and laying of 20mm dia CPVC Pipes SDR 11 & Plain CPVC SDR 11 fittings on walls/ceiling or laying in floors complete all as specified and as directed. |
| 73 | Supplying and laying of 25mm dia CPVC Pipes SDR 11 & Plain CPVC SDR 11 fittings on walls/ceiling or laying in floors complete all as specified and as directed. |
| 74 | S&F in Repairs Brass CP mixer for mixing hot & cold water screwed down for iron pipe and fixed complete all as specified and as directed by Engineer-in-Charge. |
| 75 | S&F in Repairs Vitreous China wash down water closet pan (pedestal pattern) including seat cover, white including connection to trap and to flushing pipe, anti syphonge pipe etc, including making good the floor complete all as specified and as directed. |
| 76 | S&F Vitreous china CASCADE type WC single piece-WC with PP seat Cover, hinges, fixing accessories set, cistern fittings complete of size 640 x 360 x 690 mm , P trap-180mm in approved colour complete all as specified and as directed. |
| 77 | S&F in Repairs, 10 ltr capacity, PVC flushing cistern, white, syphonic action type, low level, with inlet, ball valve float and handle, PVC flush pipe, brackets etc complete all as specified and as directed by Engineer-in-Charge. |
| 78 | S&F in Repairs chromium plated two way bib cock 15 mm bore complete all as specified and as directed by Engineer-in-Charge. |
| 79 | S & F in Repair chromium plated hand shower (health faucet) 1 meter, with PVC tube with wall hook , complete all as specified and as directed by Engineer-in-Charge. |
| 80 | S&F in Repairs Bib tap cast copper alloy chromium plated 15mm dia with fancy type screwed down screwed for iron pipe or brass ferule etc complete all as specified and as directed by Engineer-in-Charge |
| 81 | S&F Vitreous China Wash hand basin, white flat back size 550x400 mm including brackets(including Pillar Tap 15 mm bore Chromium plated cast copper alloy with capstan heads, 32 mm waste coupling brass chromium plated suitable for wash hand basins, with long screwed shanks and fly nuts & PVC waste pipe complete all as specified and as directed |
| 82 | S&F in Repairs Stop Valves / Angle Cock Fancy Type Chromium plated 15mm Bore cast copper alloy screwed down high pressure with crutch or butterfly handles screwed both ends complete all as specified and as directed. |
| 83 | S&F in Repair Pillar taps cast copper alloy, fancy type, with capston head, chromium plated, 15mm dia ,screwed down high pressure, with or without lettered Hot or Cold with long screwed shanks and fly-nuts, screwed for iron pipe and fixed complete all as specified and directed |
| 84 | Supply only looking mirror Bevelled Edge 600mmx450mm mounted on 6mm thick AC building board or commercial ply wood and fixed to wooden plugs with chromium plated brass screws and cup washers complete all as specified and as directed. |
| 85 | S & F in Repairs Brass chromium plated shower rose 125mm size with or without swivel joints, including fixing to steel pipe or union complete all as specified and as directed. |
| 86 | S & F in Repairs soap dish, any type, fixed to plugs with chromium plated brass screws complete all as specified and as directed by the Engineer-in-Charge. |
| 87 | S&F in Repairs sink with drainage board made of stainless steel 1 mm thick kitchen or laborary with plugs, washers and wastes; including bedding in cement mortar on to dwarf wall or including fixing cantilever brackets and connecting union to pipe, overall size 495 mm x 420 mm with bowl size 915 mm x 460 mm bowl size 410mm x 330mm x 160 mm including waste coupling and waste pipe complete all as specified and as directed. |
| 88 | S&F Stainless steel grade 304, 0.50mm thick, glossy finish, wall mounted kitchen plate rack assembeled set of 750 x 600 x 250mm size and fixed with screws complete all as specified and as directed. |
| 89 | S&F in Repairs Aluminium anodised chromium plated tubular towel rail, 20mm dia, D type, 60cm long, between flanges including suitable bracket complete all as specified and as directed by Engineer-in-Charge. |
| 90 | S&F PVC flexible connections 15 mm dia 450 mm long with brass checknuts complete all as specified and as directed. |
| 91 | S&F Brass CP 15mm dia bore Central hole basin mixer with regular spout without popup waste system with 450mm long braided hoses, 20mm cartridge size also available complete all as specified and as directed by Engineer-in-Charge. |
| 92 | S & F in Repairs chromiium plated Bottle trap of 32mm bore for wash basins with inlet and outlet screwed for pipe or connections including necessary packing, union, cap & fixed complete all as specified and as directed. |
| 93 | S&F in Repairs Gun metal , globe or gate valves, 20 mm dia bore, with iron wheel head, screwed both ends for iron pipe and fixed complete all as specified and as directed. |
| 94 | S&F in Repair PVC (SWR) pipes 75mm dia single socketed in any length with rubber ring joints,fixed to floor, & walls heights up to 9M including taking down complete all as specified and as directed. |
| 95 | S&F in Repair PVC (SWR) pipes 110mm dia single socketed in any length with rubber ring joints,fixed to floor, & walls heights up to 9M including taking down complete all as specified and as directed. |
| 96 | S&F in Repair PVC (SWR) bend 75mm dia with any radius complete all as specified and as directed. |
| 97 | S&F in Repair PVC (SWR) branch piece 75 mm dia (single Y) equal or unequal with oval access door complete all as specified and as directed. |
| 98 | S&F in Repair PVC (SWR) Tee 75mm dia single junction with any radius with wall access door complete all as specified and as directed. |
| 99 | S&F in Repair PVC (SWR) bend 110mm dia with any radius complete all as specified and as directed. |
| 100 | S&F in Repair PVC (SWR) Tee with single junction 110mm dia with any radius with wall access door complete all as specified and as directed. |
| 101 | M & L for Water proofing treatment with the following specifications including taking down existing roof treatment of any description and cleaning with water and scrubbing and disposing off the rubbish outside the premises, complete all as specified and as per manufacturers instructions:- (i) Rendering 10mm thick in CM 1:4 on concrete surfaces mixed with water proofing compound @ 3% by weight of cement as leveling course (ii) Apply a coat of hot blown bitumen 85/25 @ 1.20 kg/sqm over a coat of bituminous primer @ 0.3 ltr per sqm. (iii) Laying APP membrane (STP Aquashield or equivalent) weighing not less than 3.5 Kg/sqm, reinforced with polyster non woven fabric (weighing not less than 150 gms/sqm) with 100mm over laps both longitudinally and transversally and overlaps shall be sealed by torch, membrane shall be taken to the parapet through fillet and shall be tucked in inside after a height of 300 mm. (iv) Apply one coat of hot blown bitumen 85/25 @ 1.2 kg/sqm over the membrane.Note :- Water proofing compound shall be measured and paid separately. Please Enable Macros to View BoQ information |
AI Tender Summary
Tender Timeline
Jul 11, 2026
11:30 IST
Tender Published
Tender notice published.
CompletedAug 04, 2026
17:00 IST
Bid Submission Deadline
Online submission via eProcurement portal.
Upcoming · 3 daysAug 07, 2026
Bid Opening Date
Technical bids will be opened and evaluated.
Upcoming · 6 daysTender Documents
Download All (ZIP) ↓
Disclaimer
We takes all possible care for accurate & authentic tender information. However users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender