Tender For Special Repair To Or Md Accn Bldg No P-423 (06X Qtrs) And P-425 (06X Qtrs) At Usman Vihar At Bd Bari Mil Stn Under Ge Kaluchak
Tender Value
46.64 Lakhs
Estimated cost
Bid Submission
01 Aug 2026
21 days left
EMD
93300
Bank guarantee accepted
Document Fee
500
Non-refundable
Tender Type
Online
Tender Overview
Organization
Tender ID
Competition Type
NCB
Bidding Type
Tender
Location / State
Kaluchak → Jammu and Kashmir
EMD Exemption
Available
Quantity
Not Available
Website
Contact Person
Address
Project Description
Tender For Special Repair To Or Md Accn Bldg No P-423 (06X Qtrs) And P-425 (06X Qtrs) At Usman Vihar At Bd Bari Mil Stn Under Ge Kaluchak
BOQ
| Sl. No. | Item Description |
| 1 | Taking down cement plaster on bricks or stone wall/ decayed surfaces of concrete from roof projection or RCC Chajjas etc. including racking out joints, hacking for key, scrubbing down with water, etc including removing the waste out of defence land all as specified and as directed. |
| 2 | M&L rendering 10 mm thick on fair faces of brick work or concrete surfaces in CM 1:6 finished even and smooth without using extra cement complete all as specified and as directed. |
| 3 | M&L Rendering 15 mm thick on fair faces of brick/concrete surfaces in cement plaster 1:4 finished even and smooth without using extra cement, using water proofing compound mix as per manufacturer instructions, complete all as specified and as directed. (WPC measured and paid seperately) |
| 4 | M&L Rendering 5 mm thick on concrete surfaces in CM 1:3 finished on even and smooth without using extra cement as in ceiling, Chajja etc.complete all as specified and as directed |
| 5 | Material & Labour for RCC chajja/fascia/parapet repair by using following steps :-(a) Removal of existing concrete along with loose damaged and cracked concrete/cover concrete from chajjas etc, exposing corroded steel reinforcements upto a depth of 10mm minimum behind the reinforcement by chipping/hacking with chisel and hammer or by mechanical means like chisel hammer, pneumatic chippers including high pressure water jetting to chipped concrete and reinforcement all as directed by Engineer-in-charge. Hard concrete shall not be removed. However if the rebar is corroded, concrete around it shall be removed.(b) Cleaning the surface of reinforcement bars from dust by using wire brushes and dry cloth and applying FOSROC Rebakleens RR- Rust Remover or equivalent using small brush and allow to react it for 16-24 hrs. (c) Providing and applying two coats of Fosroc Nitozinc Primer - two component, zinc rich epoxy, anti-corrosive protective coating or equivalent by brushes to the exposed and cleaned rebars with an interval of 45minutes to 1 hour @ 40microns DFT / coat and allowed to completely dry for 24 hours all as directed. |
| 6 | Taking down chowkats or frames n. exc. 1.5 sqm each but with shutter without taking off shutters from the frame. complete all as specified and as directed. |
| 7 | Taking down chowkats or frames exc. 1.5 sqm & n.exc. 4 sqm each but with shutter without taking off shutters from the frame. complete all as specified and as directed. |
| 8 | M&L Pressed steel frame for door with one or more rebates including necessary lugs, fixing lugs hinges, lock strike plate etc. of size 125mm x 60 mm and made of 1.25mm thick MS sheet, complete all as specified and directed including necessary welding complete and including medium weight 03 Nos of MS butt hinges of size 75mm / 100mm / 125mm and 01 No 50mm Size of medium weight MS butt hinge complete all as specified and directed. |
| 9 | M&L PCC (1:3:6) type C-2 (40 mm graded aggregate) filling back of chowkats complete all as specified and directed.. |
| 10 | M&L 35 mm thick Flush shutters, solid core construction, with block board core and plywood face panels, commercial type on both sides with both face is covered with deco rative face veneer with lipping/frame to match complete all as specified and directed. |
| 11 | S&F 35mm thick 2nd class hard wood Glazed and skeleton shutters open rebated & prepare to receive glass, gauge etc (without sash bars /edges of framing plain chamfered or rounded, fitted with cut and mitred beds for securing glass etc) size of members of shutters complete all as specified and as directed. |
| 12 | S&F Framed brackets of angles or tees with web and flanges cut to shape for cooler stand, drilled and countersunk for screw, including bending and welding angles, as necessary, gusset plates, riveting, etc.. n exc 10 kg each brackets, conforming to Fe.290.Gde-E-165 complete all as specified and as directed. |
| 13 | S&F Solid PVC door frame of size 50mm x 47mm made out of 5mm plain colour PVC sheet reinforced with MS square tube, suppling and fixing in opening. complete all as specified and directed |
| 14 | S&F factory made solid PVC moulded door shutter with wood free EPS 28 to 30mm thick (Stile) with flush panel with 2mm thick moulded PVC sheet on the front face & 2mm plain colour PVC sheet on back face complete all as specified and as directed. |
| 15 | Steel ventilator with top hung shutter including hinges, steel peg stay, lugs as in hold fast with locking arrangements, complete all as specified and as directed. |
| 16 | S&F Box type steel windows comprised of tubular frame and shutters made out of 1.25 mm thick MS sheet tube factory made with double side shutters wire gauged shutter & glass glazed shutter (wire cloth and glass panes will be measured and paid seperately) with side hung shutters with MS handles and MS peg stay dovetailed or welded incl 02 Nos, MS Tower bolts 150 mm long for each leaf and 8 mm square bar grill / guard bars at spacing as shown on Drg welded to MS flat iron frame work ,including other fittings ,hinges ,MS handles ,tarred hold fasts ,PCC blocks for hold fasts etc all as shown on Drg No CEPZ/CE -TD/031/2013 SHEET NO 142 including one coat of red oxide zinc primer, complete all as specified and directed |
| 17 | S&F Galvanized mild steel wire cloth 0.45 nominal dia of wire and average width of aperture 1.18mm and fixed with tinned tank or galvanized wire staple complete all as specified and as directed. |
| 18 | M&L Sheet glass, ordinary quality, 3mm thick and glazed with oil putty or wooden beads, in square n exc. 0.5 Sq m each pane, complete all as specified and as directed. |
| 19 | M&L 3mm thick figured glass, pin head type and glazing with oil putty or wooden beads in square n.exc 0.5 sqm each. complete all as specified and as directed. |
| 20 | S&F Aluminium alloy, anodised, sliding door bolt with hasp, staple (both type) 300mm longh, and fixing clips of sheet cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast-aluminium alloy and fixed complete all as specified and as directed. |
| 21 | S&F Aluminium anodised 150mm long barrel tower bolt of extruded section and fixing complete all as specified and as directed. |
| 22 | S&F Aluminium handles cast type anodised 150mm complete all as specified and as directed. |
| 23 | S&F Butt hinges 100mm medium weight stainless steel complete all as specified and directed. |
| 24 | S&F Aluminium anodized barrel tower bolt of extruded section and fixed complete of size 125 mm long complete all as specified and as directed. |
| 25 | S&F Aluminium handle cast type anodized of size 125mm complete all as specified and as directed. |
| 26 | S&F Floor door stopper of aluminium alloy body and tongue, anodised with hard drawn steel springs, fixed in floor with over all length of cover plate 150mm complete all as specified and as directed. |
| 27 | Dismantling floor, hearth or wall tiling , terrazzo topping on walls including cement mortar , bedding (but no backing) removing serviceable tiles and rubbish off the premises complete all as specified and directed. |
| 28 | M&L for sunken treatment with glass fiber reinforced modified cementitious coating system before the final coat of Latex Shield 2K (or equivalent) complete all as following :-Base Coat : Berger HS Latex plus (or equivalent)consumption base coat : 0.3 kg/m2Reinforcement : Glass fiberSecond and Third coat : Latex sheild 2K (or equivalent)Consumption top coat : 3 kg/m2System reqquirements : density : 2.00 kg/ltr;Compressive strength: 0.5N/mm2Wall penetration through the RCC slab must be sealed using Berger HS Repair (or equivalent).Intersection of base slab with wall must be provided with a 50 mm fillet using Berger HS Latex plus (or equivalent) modified mortar with a bonding coat of Berger HS Latexplus (or equivalent) modified cement slurry upto sft.All depressions, unevenness, surface honeycombng shal be repaired using Berger HS Latex plus (or equivalent) modifiled polymer mortar with a bonding coat of Berger HS latex plus (or equivalent) modified cement slurry.Including cleaning of RCC surface to remove dust, loose paricles, etc with compressed air or any other suitable technique depending on site conditions, grinding aby sharp edges, etc.Note :-The concerned items should be executed by OEM authorized applicator after signing of MOU (format attached as Appendix 'AB' on page no. 101 of tender documents as per Sch 'A' Note No 19 Page No 17). |
| 29 | M&L rendering 10 mm thick on fair faces of brick work or concrete surfaces in CM 1:4 with water proofing compound tobe finished even and smooth without usingextra cement complete all as specified and as directed (WPC to be measured separately) |
| 30 | Supply only Integral water proofing compound liquid complete all as specified and as directed. |
| 31 | S&F 20mm dia High density polyethylene pipes (HDPE) of pressure rating 6 kgf/cm2 laid in as spout pipes to pour out rsidual water out from the treated area. complete all as specified and as directed. |
| 32 | M&L for hard core, of broken bricks broken to gauge n exc 63mm for laying sub base of thickness 150mm complete all as specified and directed. |
| 33 | M&L Cement concrete type D-2 1:4:8 (40mm graded crushed stone aggregate) in foundations, filling and mass concrete in sub base complete all as specified and as directed. |
| 34 | M&L for 25mm thick PCC (1:2:4) type B1 with 20mm graded aggregate for laying floor tiles complete all as specified and as directed. |
| 35 | M&L for non skid coloured Ceramic tiles 8 to 10 mm thick in light shade (square/ rectangular) polished, area of each tiles exc 0.11 sqm but not exceeding 0.18 sqm, in floors/Skirting etc. set, jointed and pointed with HS tile adhesive anti slip white @1.2kg/sqm thickness upto 8 to 10mm (or equivalent) and epoxy material for sealing of tile joints with Berger HS Epoxy tile grout(or equivalent) to the floor of toilets and bathroom |
| 36 | Demolition of cement concrete in and paving (un reinforced) exc. 15 cm. thickness, below or above ground level, including removal of waste from defence land and dumping at a place as specified by civil authorities complete all as specified and as directed. |
| 37 | Demolition of cement concrete in and paving (un reinforced) n exc. 15 cm. thickness, below or above ground level, including removal of waste from defence land and dumping at a place as specified by civil authorities complete all as specified and as directed. |
| 38 | M&L Non - skid ceramic coloured jointless tile 400mm x 400mm x 7mm thick as in floors laid over and including 15 mm thick screed bed or bedding layer of cement mortar 1:4, set and jointed in neat cement slurry and pointed in coloured cement to match the colour of tiles complete, all as specified and directed. |
| 39 | M&L Non - skid ceramic coloured jointless tiles 400mm x 400mm x 7 mm thick on vertical surfaces such as skirting /dado etc bedded & jointed in neat cement slurry over and including 10 mm thick backing coat of cement mortar 1:4 and pointed in white or coloured cement to match the colour of tiles complete, all as specified and directed. |
| 40 | M&L Glazed ceramic coloured tiles of size350x450x7 mm thick as in vertical surfaces such as skirting, dado, wall etc., set and jointed in neat cement slurry and pointed with coloured cement to match over and including 10mm thick rendering in cement mortar 1:4, complete all as specified & directed. |
| 41 | M&L Non skid ceramic tiles 7 to 8mm thick ( square/rectangular) area of each tilesexceeding 011 sqm but notexceeding 0.18sqm, as in floors etc bedded & jointed in neat cement slurry over and including 15 mm thick screed bed in cement mortar 1:4 and pointed in white or coloured cement to match the colour of tiles, complete all as specified and directed. |
| 42 | M&L Non skid ceramic tiles 7 to 8mm thick ( square/rectangular) area of each tilesexceeding 011 sqm but notexceeding 0.18sqm, on vertical surfaces such as skirting / dado etc bedded & jointed in neat cement slurry over and including 10mm thick backing coat of cement mortar 1:4 and pointed in white or coloured cement to match the colour of tiles,complete all as specified and directed. |
| 43 | M&L 18 to 20mm thick black Granite stone (table rubbed and polished) in cooking plateform bedded and jointed with grey cement slurry and pointed with white cement with admixture of pigment to match the shade of granite stone including 15mm thick screed bed in CM 1:4 after roughing surfaces of old concrete floor by picking sweeping down with water to remove dust etc including cutting holes into or through reinforced cement concrete slabs , for gas pipe (Superficial area exc 100 sq cm but n. exc. 250 sq cm. complete all as specified and as directed. |
| 44 | M&L 20mm dia stainless steel drapery rods in one length per door/window as approved by GE providing with two nos of Bracket for holding curtain rod and Fiber fancy dome type or wall to wall fixed in repair complete all as specified and as directed. |
| 45 | S&F 300mm ordinary rat tail mild steel rod pattern springs incl roller and roller plate complete all as specified and as directed. |
| 46 | Dismantling water tanks exceeding 250 ltr capacity but not exc 500 ltrs complete all as specified and as directed. |
| 47 | S&F Rotational molded polythene water storage tank triple layer vertical type with closed top hoisted and fixed in position all as spd in SSR part-I capacity 1000 liter . complete all as specified and as directed. |
| 48 | S&F in repair 20 mm ball valves high pressure of PTMT with epoxy coated , brass rod & high density plastic ball screwed for iron pipe min wt 210 gms. complete all as specified and as directed. |
| 49 | Taking up or down 15 mm steel tubing and connections including clearing for refixing or removal to store. complete all as specified and as directed. |
| 50 | Taking up or down 20 mm steel tubing and connections including clearing for refixing or removal to store. complete all as specified and as directed. |
| 51 | S&F Steel water tubing medium grade galvanised with all fittings including short lengths, fixed to walls, concealed in wall and ceiling or laid in floor complete with all fittings (such as bends, elbows, Tee, short pieces, connectors, back nuts, diminishing pieces, caps and plugs, unions etc.) of nominal bore dia15 mm, complete all as specified and as directed. |
| 52 | S&F Steel water tubing medium grade galvanised with all fittings including short lengths, fixed to walls, concealed in wall and ceiling or laid in floor complete with all fittings (such as bends, elbows, Tee, short pieces, connectors, back nuts, diminishing pieces, caps and plugs, unions etc.) of nominal bore dia 20 mm, complete all as specified and as directed. |
| 53 | Refixing old steel tubing and connections in new or old position with all fittings retrieved from Serial here-in-before and fixed (walls, ceiling, floors, etc) of 15 mm dia complete all as specified and as directed. |
| 54 | Refixing old steel tubing and connections in new or old position with all fittings retrieved from Serial here-in-before and fixed (walls, ceiling, floors, etc) of 20 mm dia complete all as specified and as directed. |
| 55 | S&F Vitreous china water closet Orissa pattern long pan size 580x440mm with trap front or back inlet including integral foot rest complete fixed in repair including lime concrete bedding and connection to drain or outgoing pipe and to flushing pipe and anti siphon pipe complete all as specified and as directed. |
| 56 | S&F PVC flushing cistern white shade low level 10 ltrs capacity, white with inlet ball valve, float and handle including bracket and flush pipe including connection to pipes, fixed in repairs complete all as specified and as directed. |
| 57 | S&F PVC connection 15 mm size with PTMT nuts of length 600 mm complete all as specified and as directed. |
| 58 | S&F Tubular towel rail, brass chromium plated, 20 mm dia, D type, 60 cm long between Hangs, fixed in repairs complete all as specified and as directed. |
| 59 | S&F sinks with drainage board made of stainless steel 1mm thick kitchen or laboratory with plugs washers and wastes including bedding in cement mortar to dwarf wall or including fixing cantilever brickets and connecting union to pipe overall size 915mmx460mm bowl size 410mmx330mmx160mm. complete all as specified and as directed. |
| 60 | S&F Stainless steel grating of 125mm size, male/female pattern with or without hole, fixed in nahani/floor traps with white/coloured cement, fixed in repairs, complete all as specified & directed. |
| 61 | S&F PVC 32mm dia waste pipe with CP coupling, complete all as specified and as directed. |
| 62 | S&F in repairs vitreous china wash hand basin corner type with white and glossy including angle iron brakets, CP waste coupling 32mm & 32mm PVC waste pipe all accessories complete all as specified and directed. |
| 63 | S&F in repair Bib taps, chromium plated cast copper alloy, with capstan head, screwed down for iron pipe or for brass ferrule and fixed for bore of pipe 15 mm, fixed in repairs, all as specified and as directed. |
| 64 | S & Fixed in repairs Angle stop valve cast copper alloy, with fancy type chromium plated capstan head, screwed down, high pressure screwed both ends for 15 mm bore iron pipe or for unions and fixed complete all as specified and as directed. |
| 65 | S&F in repair CP brass hot & cold 15mm dia wall mixture with provision for overhead shower with 115 mm long bend pipe on upper sie connecting legs & wall flanges for mixing hot & cold water complete all as specified and as directed. |
| 66 | S&F in repair CP brass hot & cold 15mm dia 3 in1 wall mixture for kitchen & wall flanges for mixing hot & cold water complete all as specified and as directed. |
| 67 | S & F in repairs Chromium plated shower rose 125 mm size with or without swivel joints, any size, including fixing to steel pipe or union complete all as specified and as directed. |
| 68 | S & F in repairs 20 mm dia Gun Metal, globe or Gate Valve with Iron wheel head Screwed both ends for Iron Pipe and fixed in repairs. complete all as specified and as directed. |
| 69 | Sheet glass shelf assembly consisting of 5,5mm thick sheet glass shelf 12cm wide with chromium plated bracket guard and railing 60cm long complete all as specified and as directed. |
| 70 | S&F 600x450mm PVC cabinet mirror of superior quality complete all as specified and directed. |
| 71 | Dismantling boarding any description fixed with screws complete all as specified and directed. |
| 72 | S&F 18/19mm thick Prelaminated particle board, exterior grade, prelaminated one side with decorative choice lamination & other side balancing white lamination fixed with screws to timber frame work as in cupboards , kitchen cabinat etc fixed in repairs all as specified. |
| 73 | S&F Continuous (piano) hinges,width of flap when open is 30 mm mild steel, bright finish or electrogalvanised complete all as specified and as directed. |
| 74 | S&F 100 mm long Extruded Aluminium alloy handles, fabricated type, anodised. complete all as specified and as directed. |
| 75 | S&F Magnetic catches of 25/30 mm size for cup Board shutter etc complete all as specified and as directed. |
| 76 | S&F hasp and stapple, safety typeof Aluminium, anodised, including bolt to hinge type, fixed with screws of 100 mm complete all as specified and as directed. |
| 77 | M&L TMT steel bars 10mm dia and over, cut to length bent to shape required, including cranking, bending spirally for hooping to columns, hooking ends and binding with mild steel wire (annealed) not less than 0.90mm dia, all as specified and directed. |
| 78 | M&L TMT steel round bars 6 to 8mm dia and over, cut to length bent to shape required, including cranking, bending spirally for hooping to columns, hooking ends and binding with mild steel wire (annealed) not less than 0.90mm dia, all as specified and directed. |
| 79 | M&L Form work to soffit of suspended slab such as roof slab not exc 20 0 mm thick horizontal or slopinf flate including fair finished to concrete surfaces. complete all as specified and as directed. |
| 80 | M&L RCC 1:2:4 Type B-1 (using 20 mm graded aggregate) in Roof slab, shelves supported on wall/column and the like etc complete all as specified and as directed. |
| 81 | M&L Providing Precast cement concrete 1:2:4 Type B-1 (using 20 mm graded aggregate) in landings, cover slabs (for man holes etc) and the like etc complete all as specified and as directed. |
| 82 | Demolition of reinforced cement concrete ( reinforcement cut as required to facilitate demolition) of any description and in any position not otherwise specifically provided for complete all as specified and directed. |
| 83 | Demolition of cement concrete of any description and in any position not otherwise specifically provided for in plinth protection complete all as specified and as directed. |
| 84 | M&L 75 mm thick PCC 1:3:6 type C-1, (using 20mm graded crushed stone aggregate) as in plinth protection finished even and smooth without using extra cement incl necessary joints complete all as specified and directed. |
| 85 | Dismantling cast iron or reinforced concrete drain pipes of 75/100mm bore, fixed with walls and taking out of trenches, if required all as specified and directed. |
| 86 | S&F PVC (SWR) pipes single socketed in any length with rubbering joints fixed to walls 110mm bore. complete all as specified and as directed. |
| 87 | S&F PVC (SWR) pipes single socketed in any length with rubbering joints fixed to walls 75 mm bore. complete all as specified and as directed. |
| 88 | S&F PVC (SWR) bends any radius 110mm bore with access door. complete all as specified and as directed. |
| 89 | M&L PVC(SWR) junction single (single 'T') equal or unequal 110mm bore with access to door ccomplete all as specified and directed. complete all as specified and as directed. |
| 90 | S&F PVC (SWR) bends any radius 75 mm bore with access door. complete all as specified and as directed. |
| 91 | M&L PVC(SWR) junction single (single 'T') equal or unequal 75 mm bore with access to door ccomplete all as specified and directed. |
| 92 | M & L for PVC (SWR) multi floor trap diameter of outlet 75 mm with grating including jointing with solvent cement. complete all as specified and as directed. |
| 93 | S&F Plate rack made out of 1.00 mm thick stainless steel sheet of size 750mm x 750mm x250mm , complete all as sepcified and directed. |
| 94 | M&L 75 mm thick PCC 1:4:8 type D-2 using (40mm graded crushed stone aggregate) as in sub base of floor complete all as specified and directed. |
| 95 | M&L for Machine pressed precast concrete interlocking paver block any shape and size confirming to IS 15658-2006 of 60 mm thickness, M-35 Grade complete all as specified and directed. |
| 96 | M&L Sand filling under floors or in foundations including watering and consolidation complete all as specified and as directed. |
| 97 | M&L Preparation of new wooden surfaces of any description, over 10cm width or girth and applying two coats of synthetic enamel paint over a coat of pink primer, complete all as specified and as directed. |
| 98 | M&L for two coats synthetic enamel paint over a coat of red oxide primer on newly steel surfaces complete all as specified and as directed. Please Enable Macros to View BoQ information |
| 99 | M&L for two coats synthetic enamel paint over a coat of red oxide primer on newly steel surfaces complete all as specified and as directed. Please Enable Macros to View BoQ information |
AI Tender Summary
Tender Timeline
Jul 10, 2026
11:30 IST
Tender Published
Tender notice published.
CompletedAug 01, 2026
17:00 IST
Bid Submission Deadline
Online submission via eProcurement portal.
Upcoming · 21 daysAug 03, 2026
Bid Opening Date
Technical bids will be opened and evaluated.
Upcoming · 23 daysTender Documents
Download All (ZIP) ↓
Disclaimer
We takes all possible care for accurate & authentic tender information. However users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender