Tender For Special Repair To Bldg No. Np-03 And Np-05 And Provn Of 4Xsolar Water Heating System 100Lpd For Dsc Line Ge 574 Under Ge (W) Pathankot (Job No. (I) P-49/Sr Bldg/2025-26, (Ii) Mw/Pkt/14/2025-26
Tender Value
11.33 Lakhs
Estimated cost
Bid Submission
20 Aug 2026
13 days left
EMD
22660
Bank guarantee accepted
Document Fee
500
Non-refundable
Tender Type
Online
Tender Overview
Organization
Tender ID
Competition Type
NCB
Bidding Type
Tender
Location / State
Pathankot → Punjab
EMD Exemption
Not Available
Quantity
Not Available
Website
Contact Person
Address
Project Description
Tender for Special Repair To Bldg No. Np-03 And Np-05 And Provn Of 4Xsolar Water Heating System 100Lpd For Dsc Line Ge 574 Under Ge (W) Pathankot (Job No. (I) P-49/Sr Bldg/2025-26, (Ii) Mw/Pkt/14/2025-26
Corrigendum
| Sr No | Corrigendum Date | Corrigendum | Type | New Submission Date |
|---|---|---|---|---|
| 1 | 23-Jul-2026 | Corrigendum 01 | Date | 06-Aug-2026 |
| 2 | 30-Jul-2026 | Corrigendum 02 | Date | 13-Aug-2026 |
| 3 | 06-Aug-2026 | Corrigendum 03 | Date | 20-Aug-2026 |
BOQ
| Sl. No. | Item Description |
| 1 | Sch 'A' Part-I B/R work:-Dismantling/Demolition of existing roof (Assessable/non assessable)terracing of cement/brick concrete(un-reinforced) and existing water proofing treatment of any thickness in any position on top of roof of building, cleaning surface of roof with brush/mechanical brush and with water throughly to romove all dust/dirt and loose particles to expose bare concrete roof slab and romoval of rubbish/demolished material out side MD land complete all as specified Note : Demolition should be done by chiselling. |
| 2 | M&L for 10mm thick plaster , on fair faces of brick work or concrete surfaces and provn of on roof finished even and smooth with using liquid water proofing compound as per manufacturers instructions Complete all as specified and directed. (Note :- Supply only liquid water proofing compound shall be measured & paid separately). |
| 3 | M&L for PCC 1 : 2 :4 type B-0 (using 12.5mm graded crushed stone aggregate) as in levelling padding course over RCC roof surface including rounded or chamferred on edges etc mixed with approved water proofing compound all as per manufacturer'ss instructions on the roof surface to achieve requisite slope all as specified and directed. (Note : Supply only water proiofing compound shall be measured & paid separately) |
| 4 | Supply only polymer based liquid water proofing compound complete all as specified and directed. |
| 5 | M&L for liquid water proofing treatment to RCC roof slab in following procedure : (a) Applying first coat fiber reinforced elastometic liquid water proofing membrane formulated with PU hybrid polymers and reinforcing acrylic fibers with sun reflective index (SRI) of 100-110, having minimum elongation of 350%, tensile strength 2.9 Mpa and shall have reack bridging ability upto 2.5mm and shall resist 10 bars of hydrostatic pressure reduce surface temperature upto 10 degree celsius with 3.3% dilution as priming coat (b) laying of fiber mesh 0.3mm thickness weave in leno pattern having weight 4.5 gm/ Sqm and pasting it properly with overlap of 50mm and allow it to dry (c) Applying second coat undiluted @ 0.45 ltr/ sqm as directed by Engr-in-Charge (d) Applying third and final coat undiluted @ 0.45 ltr/ sqm . (The rate includes for filling cracks in existing roof with cement putty using suitable bonding agent (shalcrate 42) before laying cement plaster) complete all as specified and as directed by Engr-in-Charge |
| 6 | Demolition of brick work built in CM incl. taking out roots vegetation if any at any position and removal to out side MD land |
| 7 | M&L for brick work with sub class 'B' bricks straight or curved on plan exc. 6m mean radius built in CM(1:6) complete all as specified and as directed. |
| 8 | M&L for Half Brick work with burnt clay sub-class 'B' brick having crushing strength not less than 75 Kg/Sqm, straight or curved on plan exceeding 6 m mean radius with old size bricks built in cement mortar 1:4. |
| 9 | Taking down cement plaster of any description in any position including racking out joints making key scrubbing down with water etc. and removal of debris out side MD land. |
| 10 | M&L for 15mm thick cement plaster in cement mortar (1:6) on fair faces of brickwork or concrete surfaces and finished even and smooth without using extra cement . |
| 11 | M&L for Preparation of new plastered or un-plastered surfaces of wall by applying 1.5 mm thick wall care putty on plastered surfaces of wall; internal /external Birla/JK white putty smooth finished ,complete all as specified and directed. |
| 12 | M&L for preparation of new plastered surfaces of walls and applying two coats of oil bound distemper with roller over a coat of alkali resistant primer.etc complete all as specified and directed. |
| 13 | M&L for Preparation of old plastered or un-plastered surfaces of wall by applying 1.5 mm thick wall care putty on plastered surfaces of wall internal /external smooth finished complete all as specified and directed. |
| 14 | M&L for complete removal of existing surfaces including washing / rubbing down with water of wall and applying one coats of oil bound distemper primer complete all as specified and directed . |
| 15 | M&L for complete removal of existing surfaces on wall and applying two coats of white wash complete all as specified and directed. |
| 16 | M&L for rendering 5 mm thick on fair faces of concrete surface of ceiling in CM 1 : 3 and finishing even and smooth without using extra cement complete all as specified and directed.. |
| 17 | M&L for preparation of new plastered surfaces on ceiling and applying two coats of white wash with complete all as specified and directed. |
| 18 | M&L for complete removal of existing surfaces on ceiling and applying two coats of white wash with complete all as specified and directed. |
| 19 | M&L for rendering 15mm thick on fair faces of brick work or concrete surfaces in CM 1 : 4 mixed with WPC @3 % by the weight of cement used and finishing even and smooth without using extra cement complete all as specified and directed.. |
| 20 | M&L for preparation of NEW plastered walls surfaces for applying Two or more coats of 100% Premium acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives @ 1.43 litre/ 10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/ 10 sqm over new surfaces. |
| 21 | M&L for complete removal of existing surfaces including washing / rubbing down with water of wall for applying Two or more coats of 100% Premium acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives @ 1.43 litre/ 10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/ 10 sqm over new surfaces. |
| 22 | Demolition of cement concrete unreinforced in ground floors and pavings n exc 15 cm thickness (below or above ground level) |
| 23 | M&L PCC 1:3:6 type C-2 (Using 40mm graded crusged stone aggregate), 75mm thick as in plinth protection finished even and smooth using extra cement compete all as specified. |
| 24 | M&L for 25mm thick cement concrete type B-1 1:2:4 (using 20mm graded crushed stone aggragate) as in base of floor compete all as specified. |
| 25 | M&L for 75 mm thick plain Cement concrete 1:4:8, type B-2 using 40mm graded crushed stone aggregate as in sub base complete all as specified and directed. |
| 26 | S&F glass dividing strip, 3mm thick and 22mm width complete all as specified and as directed. |
| 27 | Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles and rubbish off the premises etc complete all as specified and directed. |
| 28 | M&L for Vitrified Ceramic tiles 10 mm thick coloured (square/ rectangular) polished, area of each tiles not exceeding 0.36 sqm in floors etc (size of each tile 0.6m x 0.6m), set and jointed in neat cement slurry and pointed in white or coloured cement to match over & including 15mm thick screed bed in CM 1:6 complete all as specified and directed. |
| 29 | M&L for Vitrified Ceramic tiles 10 mm thick coloured (square/ rectangular) polished, area of each tiles not exceeding 0.36 sqm in floors etc (size of each tile 0.6m x 0.6m), set and jointed in neat cement slurry and pointed in white or coloured cement to match over & including 15mm thick screed bed in CM 1:4 complete all as specified and directed. |
| 30 | M&L for Non - skid Ceramic Coloured tiles 7 to 8 mm thick (square/rectangular) area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match over & including 15mm thick screed bed in CM 1:4 complete all as specified and directed. |
| 31 | M&L for Coloured glazed ceramic tiles of size 350x 450 x 7mm thick,on vertical wall surface, set and jointed in neat cement slurry and pointed in white or coloured cement to match the surfaces inc rendering cement plaster, 10mm thick in cement mortar 1:4 on fair faces of brick work or concrete surfaces to receive tiles complete all as specified and directed. |
| 32 | Taking down chowkats of frames with shutters (without taking off shutters from frames) area exceeding 1.50 Sqm but n exc 4 sq. m each, including cutting holes for taking out hold fasts or dismantling brick work (holes cut and any other damages to jambs , walls for taking out hold fast shall be finished idetical to existing finish without any all as specified and directed by Engr- in - charge |
| 33 | Taking down chowkats of frames with shutters (without taking off shutters from frames) area not exceeding 1.50 Sqm each, including cutting holes for taking out hold fasts or dismantling brick work (holes cut and any other damages to jambs , walls for taking out hold fast shall be finished idetical to existing finish without any extra cost of Govt) all as specified and directed by Engr- in - charge |
| 34 | Taking down shutters of any description exc.1 sq.m and n.exc. 2 sq.m each complete all as specified and directed. |
| 35 | S&F Pressed steel door frame of size 105x60mm, double rebated for doors made out of 1.25mm thick mild steel sheet including necessary fixing lugs, hinges lock strike plate etc, complete all as specified and directed. |
| 36 | S&F Factory made 35mm thick Flush shutters, solid core construction, with block board core and plywood face panels, commercial type on both sides complete all as specified and directed. |
| 37 | S&F extruded Powder coated aluminium section as in Anodised aluminium frame for doors, windows, ventilators with one or more rebates including joining cleat for fixing etc. complete all as specified and all directed |
| 38 | S&F Anodised aluminium window and ventilator shutters, and top side hung type without sash bars, aluminium sections weighing 0.55 kg/m including necessary joining cleats, glazing clips, rubber packing, anodised aluminium snap beading, screws, anodised aluminium fittings such as peg stays 150mm long (1 no.). hinges type B-21 100mm long (2 no.) suitable handle (1 no.) complete all as specified complete all as specified and all directed |
| 39 | S & F Anodised aluminium door shutters, aluminium section weighing 0.55 kg/m including necessary joining cleats, glazing clips, ruber neoprene packing, handles 2 Nos in each door, hinges, anodised aluminum snap beading screws etc. complete all as specified complete all as specified and all directed |
| 40 | S&F 4.8mm thick glass selected quality in each pane for aluminimum door shutters, aluminium partition wall and sliding windows/ventilator shutters etc including rubber beading or gasket for aluminium section n exc .5 Sqm complete all as specified. |
| 41 | S & F aluminium grill conforming to DG- 102 of Deco Grill or equivalent , (10mm X 5.2mm) thick of approved design or equivalent as approved by Accepting Officer and fixing with and including 'F/U' channel not less than 1.5mm thick complete all as specified and directed. |
| 42 | S&F Aluminium alloy wire cloth, 0.45mm nominal dia of wire and average width of aperture 1.40mm and fixed with aluminium wire staples complete all as specified and directed. |
| 43 | S&F Steel window/ventilator factory made, made out of mild steel box type and shutter suitable for double shutter i.e. Glazed and gauged shutter. Glazed shutter made out of hollow' section with sash bar and gauged shutter made out of hollow section without sash bar including hinges, tower bolt, handle, grill 10 mm sq bar including two coat of synthetic enamel paint over one coat of red oxide primer, tarred hold fasts, PCC bed blocks for fixing hold fast, including plain/figured glass 3mm thick and stainless steel wire cloth 0.36mm nominal dia of wire & average width of aperture 1.18mm & fixed with stainless steel wire staples`etc complete all as per details shown in drawing No CEPZ/C-TD/032/13 sheet No 1/2 & 2/2 including taking down existing spoiled and unserviceable windows/ventilators of any type ( wooden/steel) complete all as specified and directed |
| 44 | S&F Factory made solid PVC door heat moulded frame of size 50 mm x 47 mm made out of 5mm plain colour PVC sheet reinforced with M.S. square tube, in opening as specified and directed. |
| 45 | S&F Factory made solid panel PVC door shutter 24 to 30 mm thick (style) consisting of frame made out of M.S. tubes for top & bottom rails, M.S. frame shall be covered with heat moulded both side prelam PVC ‘C’ channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and both side prelam PVC sheet for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail; Panelling of both side prelam PVC sheet to be fitted in the M.S. frame welded / sealed to the stiles & rails with suitable PVC sheet beading, and joined together with solvent cement as per specification & drawing complete all as specified and directed. |
| 46 | S&F 250 mm long aluminium alloy anodised sliding door bolt with hasp & staple (bolt type) and fixing clips of sheet, cast or extruded section and fixing bolts and sliding bolts of exturded sections or cast aluminium alloy all as specified and directed |
| 47 | S&F 150 mm long aluminium bow handles cast type anodised. |
| 48 | S&F 200 mm long aluminium anodised barrel tower bolt of extruded section. |
| 49 | S&F butt hinges med weight cold rolled MS, size 100 mm. |
| 50 | M&L for preparation of new wooden surfaces of any description not otherwise described over 10 cm width or girth and applying two coats of synthetic enamel paint over a coat of pink primer complete all as specified. |
| 51 | M&L for preparation of old wooden surfaces of any description not otherwise described over 10 cm width or girth and applying one coats of synthetic enamel pain complete all as specified. |
| 52 | M&L Cutting chases, pinning in, making good to facings where required and pointing in cement mortar 1:3 toends or edges of landings, steps, cills, sunshades, shelves, lintels, etc.; and cutting chases for concealedwater tubing or concealed conduit wiring, etc. and making good, cutting exceeding 20cm girth complete all as specified and directed |
| 53 | Taking up or down steel tubing with connections for cleaning for refixing or removing to store yard complete of bore15mm complete all as specified. - |
| 54 | S&F Steel water tubing medium grade galvanised with all fittings including short length , fixed to walls and ceiling and laid in floor complete with all fittings (such as bends, elbows, Tee , short pieces, connectors, back nuts, diminishing pieces, caps and plugs, unions etc) of nominal bore dia 15mm complete all as specified. |
| 55 | Taking up or down steel tubing with connections for cleaning for refixing or removing to store yard complete of bore20 mm complete all as specified. - |
| 56 | S&F Steel water tubing medium grade galvanised with all fittings including short length , fixed to walls and ceiling and laid in floor complete with all fittings (such as bends, elbows, Tee , short pieces, connectors, back nuts, diminishing pieces, caps and plugs, unions etc) of nominal bore dia 20mm complete all as specified. |
| 57 | Demolition carefully RCC work as in, Roofs, floors (other than ground floors), beams, staircases, landing,chajjas and similar suspended worketc by low impact Hammer/Breakar without damaging the structure & cleaning and disposal of debris out side the MOD land. complete all as specified and directed. |
| 58 | M&L for reinforced cement concrete 1 : 2 : 4 type B-0 (using 12.5 mm graded crushed stone aggregate) for Chajja beams, cantilevers etc complete all as specified and directed. |
| 59 | M&L for Use and waste of Formwork to soffits of suspended slabs such as roof slabs,chajja, water tank staging floor slabs, landings and similar work; not exceeding 200mm thick (Horizontal or sloping)for flat and rough surfaces complete all as specified and directed. |
| 60 | M&L for TMT bars 10mm dia and over cut to length, bent to shape reqd, inculding cranking,bending spirally for hooping for Columns, hooking ends and binding with and incl MS wire(annealed) not less than .90mm dia complete all as specified and directed. |
| 61 | S&F rotational moulded polythylence water storage tanks 500 Ltr cylindrical vertaical with closed top) hoisted and fixed in position all as specified in SSR Pt-I of 500 ltrs including disconnecting the unserviceable existing rcc/pvc tanks complete screwed for iron pipe or brass ferrule directed |
| 62 | S&F in repairs Ball valve high pressure of PTMT with epoxy coated Aluminium rod & highdensity plastic ball screwed for iron pipe and fixed complete 25mm dia complete all as specified and directed. |
| 63 | S&F Nipple suitable for HDPE water tank (minimum weight 25mm - 65 gms) 25mm bore dia complete all as specified and directed |
| 64 | S&F in repair Vitreous China wash down water closet pan (pedestal pattern), white (excluding fixing bolts, flushing cistern and flush pipe),Pedestal pan and trap, including connection to drain (or outgoing pipe) and to flushing pipe, antisyphonage pipe, etc. complete, including Plastic water closet seat, white, closed pattern with flat bottom, and cover and mild steel chromium plated or aluminized hinging device complete all as specified and directed. |
| 65 | Supply only PVC connector 15mm size with PTMT nuts of length 450mm |
| 66 | S&F in repair PVC valveless, syphonic action type, 10 ltrs cap flushing cistern, low level, white, with inlet, ball valve, float and handle including brackets and flush pipe 32mm dia and fixed in repairs complete all as specified and directed. |
| 67 | S&F in repair wash basin, Vitreous China white (Flat back) 630 x 450mm including fixing granit top with ceramic under counter basin pinning in ends of brackets or erecting stand including fixing of waste pipe and pillar tap and waste pipe complete all as specified and directed. |
| 68 | S&F in repair 15mm bore dia brass CP mixcher for mixing hot and cold water screwed down for iron pipe and fixed for WHB bath complete all as specified and directied |
| 69 | S&F in repair Angular Stop Cock with Wall Flange 15mm bore dia, cast copper alloy fancy type jaqwar/Prayag/Player |
| 70 | S&F in repair, water jet chromium plated for vitreous china pedestal pattern water closet of approved make all as specified and directed. |
| 71 | S&F in repair health faucet (ABS Body) mild steel chromium plated suitable for 15 mm dia pipe with 1.25 metre long flexible tube and ABS wall hook including making connections and fixed in position complete in all respect as specified. |
| 72 | S&F in repair brass chromium plated towel rail 20mm dia, \\"D\\" type, 600mm long between flanges. |
| 73 | S&F in repair stainless steel soap dishes approximate size 160mm x 160mm x90mm as complete as specified as directed by Engineer-in-Charge. |
| 74 | S&F in repair Glass Assembly sheet glass consisting of 5.5mm thick sheet glass 12cm wide with chromium plated bracked guard and railing 60cm long in repairs complete all as specified and directed.. |
| 75 | S&F in repair Brass chromium plated shower rose 125mm size including fixing to steel pipe or union in repairs complete all as specified and directed. |
| 76 | S&F in repair stop valves 15mm bore dia, cast copper alloy fancy type, chromium plated with long shank and cup concealed type, screwed down high pressure, with crutch or butterfly handle, screwed both ends for iron pipe or for unions in repairs complete all as specified and directed. |
| 77 | S&F in repair 32 mm bore low density polyethylene pipes (LDPE) of pressure rating 6 kgf/cm2 PVC bends including all necessaryfixed complete to walls, ceilings or in floors etc. |
| 78 | S&F in repair bib tap brass 15mm bore dia chromium plated long shank fancy type 2-way Bib Cock with Wall Flange screwed for iron pipes complete in repairs complete all as specified and directed.jaqwar/Prayag/Player |
| 79 | S&F in repairs brass chromium plated bathroom wall (wall mounted model) mixture with telephonic shower arrangement with swivel wall hook with and including old Victorian design telephone shower with 12mm dia 1.5m long flexible tube and swivel hook etc. make- jaqwar/Prayag/Player complete all as specified and directed. |
| 80 | S&F in repair 25mm dia, fancy type decorative,ss curtain rod including brackets and nobs each road 2 nos complete all as specified and directed. |
| 81 | S&F in repair 20 mm Gun-metal, globe or gate valves,with iron wheel head, screwed both ends for iron pipe complete all as specified and directed. |
| 82 | Taking down AC / PVC rain water pipe any size or pattern incl all fittings heads, shoes, bends. Swan necks, etc including cleaning for refixing or removing to store. |
| 83 | M&L for 110 mm dia PVC (SWR) pipe single socketed (ISI marked) fixed fixed to wall with mild steel clamps complete all as specified and directed. |
| 84 | M&L for PVC (SWR) 110mm bends any radiusequal complete all as specified and directed. |
| 85 | M&L for 75 mm dia PVC (SWR) pipe single socketed (ISI marked) fixed fixed to wall with mild steel clamps complete all as specified and directed. |
| 86 | M&L for PVC (SWR) 75 mm bends complete all as specified and directed. |
| 87 | M&L for 100 mm ,PVC (SWR) floor trap, plain with grating including jointing with solvent cement complete all as specified and directed. |
| 88 | M&L for 100 mm PVC (SWR) multi floor trap with grating including jointing with solvent cement complete all as specified and directed. |
| 89 | Dismantling timber scantling 40 Sq cm and over in section, in any position framed work complete all as specified and directed |
| 90 | Dismanting of Asbestos cement (corrugated, semi corrugated , etc) sheets in roof coverings etc complete all as specified and as directed. |
| 91 | S&F Roof trusses (framed), trussed, purlins, crane gantries, rails and fastenings and heavy bracket framing (Beam, tee, angle, channel, post or flat sections) including distance pieces, cleats etc. Fe-410- W(Gde-E-250) quality-B including distance pieces, cleats plate etc incl required welding as per relevent IS complete all as specified and directed. |
| 92 | S&F rolled mild steel work in plates (plain or chequered) channels, square cut or notched (ordinary and countersunk) forming holes, without any attachment, Fe 410-W (Gde-E-250) quality-B, complete all as specified and directed. |
| 93 | S&F Pre- painted galvalume aluminum zinc coating GI based corrugated steel sheet 0.50mm thick of an colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws as specified |
| 94 | S&F Pre-painted galvalume aluminum zinc coating GI based Plain steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws as specified |
| 95 | M&L for Preparation of new steel surfaces of any des-cription, over 10cm in width or grith, not otherwise described and applying two coats of synthetic enamel paint over a coat of red oxide primer.complete all as specified and directed. |
| 96 | M&L for Preparation of old steel surfaces of any des-cription, over 10cm in width or grith, not otherwise described and applying one coats of synthetic enamel paint over a coat of red oxide primer.complete all as specified and directed. |
| 97 | S&F mild steel work in tubular trusses including special shaped washer etc. complete using ERW or induction butt welded tubes conforming to I. S.1161- 1979 grade St.-240 complete all as specified and directed. |
| 98 | Sch 'A' Part-I E/M work:-Taking down carefully copper or aluminium point wiring (light, fan, socket or power) complete, including fixture and fittings such as switches, ceiling roses, pendants, sockets bulk, head fitting, tube light fitting by unscrewing carefully from boards etc and making good, distrubed surface of walls floors etc. |
| 99 | M&L for point wiring for light / fan controlled by one switch with 1.50 sqmm PVC insulated unsheathed multistrand copper conductor FRLS-H cable in existing PVC concealed conduit terminated in new anodise pressed steel sunken box of approved thickness with ISI marked bakelite laminated sheet fixed with cadmium plated screws and washers for switches and sockets, including 1.5 sqmm PVC insulated unsheathed multistrand copper conductor FRLS-H as earth continuity conductor connected to common earth dolly including, cutting chiseling for concealed boxes, including insulation test of point wiring and making good disturbed surface area and white wash/colour wash to matching with the existing colour complete all as specified .Note: colour coding is to be maintained .(Ph-Red, N-Black, Half -Yellow, Earth- Green). |
| 100 | All as per Srl item No 120 here-in-befor but for 5 pin 5 amps socket outlet or independent board complete all as specified and directed. |
| 101 | All as per Srl item No 120 here-in-befor but for 3 pin 5 amps socket outlet on the same board with other switch complete all as specified and directed. |
| 102 | M & L for point wiring in repair with 2.5 sqmm PVC insulated unsheathed multistrand copper conductor FRLS-H cable in existing PVC concealed conduit terminated in new anodised pressed steel sunken box approved thickness with ISI marked bakelite laminated sheet fixed with cadmium plated screws and washers for switches and sockets, including 2.5 sqmm PVC insulated unsheathed multistrand copper conductor FRLS-H as earth continuity conductor connected to common earth dolly including, cutting chiseling for concealed piping ,including insulation test of point wiring and making good disturbed surface area and white wash/colour wash to matching with the existing colour including taking down of old existing wiring any type and all as specified .Note: colour coding is to be maintained .(Ph-Red, N-Black, Half -Yellow, Earth- Green). |
| 103 | S & F switch piano flush type one way 5 amps SP 240 volts complete all as specified and directed. |
| 104 | S & F switch piano flush type one way 15 amps SP 240 volts complete all as specified and directed. |
| 105 | S & F socket outlet 2 in 1, 3 pin 5 amps flush type 240 volts complete all as specified and directed. |
| 106 | S & F socket outlet 2 in 1, 5 pin, 5 and 15 amps flush type 230 volts complete all as specified and directed. |
| 107 | S&F ceiling rose 65 x 50mm three terminals complete all as specified and directed. |
| 108 | S&F in replacement energy saving decorative 20W LED batten light fitting (3 in 1 i.e. cool white, off white and warm white) 6500K, 4000K and 3000K type, light fitting axtruded PVC houshing provided for efficient heat dissipation with polycorbonate diffuser and intregrated electronic driver complete with all accessories prewired without tube and making connections with twisted flexible copper cable of suitable size from ceilling rose/PVC connector to light fittings complete all as spd and directed by Engr -in -charge. |
| 109 | S & F LED luminaire 600 mm X 600 mm , 35/36 watt 220 V AC recessed type with high efficiency PMMA diffuser soft glare free light complete with driver holder & driver & LED lamp suitable for roof ceiling including connecting up with driver flexible copper conductor cases of suitable size complete all as specified and directed by Engr-in-Charge. |
| 110 | Taking down existing ceiling fan safely by disconnecting the electric connection and removing from ceiling of bldg by descrewing the nut, bolt etc during the execution of work and refixing/rehanging the same after completion of plastering/repairing including minor repair and fixed on ceiling with the help of new locking pin, reel insulator, nuts of suitable size and electric connection , including one coat of synthetic enemal paint of existing colour complete all as specified and as directed. |
| 111 | M&L for providing/ cutting the round/ square hole of required size in wall finishing the distrubed surfaces as per existing finishes complete all as spd and supply and fixing MS ventilating fans Single phase, 230 volts 300 mm or 12” H.D EX Fan (900 RPM) complete and supply and grouting the ragged bolts in wall, fixing the frame on the exhaust side (outer surface of the wall) and connecting with and including PVC insulated copper cable suitable size from ceiling rose to exhaust fan motor and writting MES No. with black synthetic enamel paint 2.0 cm high complete all as spd and directed by Engr-in-charge. |
| 112 | S&F in replacement of sheet metal enclosure MCB distribution board, double door with IP-43 protection single phase 240 volts 6 way, including suitable size copper bus bar and neutral link fixed flush in wall including chases in wall for fixing DB and making good the distributed wall surfaces to match with existing specification complete all as specified and directed. |
| 113 | S&F in replacement for MCB SP 240 volts any rating from 6 to 40 amps, 'C' cruve with rupturing capacity 10 KA, including providing thimble for out going cables complete all as specified and directed. |
| 114 | S&F in replacement for MCB SPN 240 volts any rating from 6 to 40 amps, 'C' cruve with rupturing capacity 10 KA, including providing thimble for out going cables complete all as specified and directed. |
| 115 | Taking down and refixing of existing hylum sheet/modular switch boards/light fittings/holder/switches/sockets/ceiling roses/etc. sheets/lights to be fitted with new suitable size screws/catcher etc complete all as specified and directed. Note:-Light fittings/holder/ceiling rose/sockets electrically connected on onehylum/modular sheet will be measured as one job only. |
| 116 | S&F in replacement sub Main Wiring with PVC insulated unsheathed multistrand FRLS-H flexible copper conductor cable of size 2x6 sqmm and one PVC insulated multistrand unsheathed FRLS-H flexible copper conductor cable of size 6 sqmm (green colour) as earthing lead connecting to main earthing dolly drawn in and including non metallic PVC concealed conduit 20mm dia complete and making good to disturbed surface complete of wall/floor with cement mortar and finishes to match the existing surface complete all as specified and directed. |
| 117 | S&F in repair 1100 volts grade heavy duty cable PVC insulated aluminium conductor, served with inner sheathing of PVC tape and overall PVC sheathed in service connection one twin core flat cable or circular 10 Sqmm including PVC conduit of suitable size complete all as specified and directed by Engr-in-charge. |
| 118 | S&F in replacement bldg secuirty light fitting energy saving high efficiency LED street light fitting 25 Watts, 5700 K, IP 66, having pressure die cast housing with toughened glass and individual high power LEDs with secondary optics, prismatic polycarbonate cover complete including GI bracket of size 25 mm dia bent to shape having length on less than 0.9 mtr fixing with clamp etc and making connections using suitable size copper cable from ceilling rose/ PVC connector to light fittings or as directed by Engr-in-chrage. |
| 119 | Supply, installation, testing and commissioning of 100 LPD capacity Flat Plate Collector (FPC) type Solar Water Heating System complete with stainless steel hot water storage tank of 100 litre capacity having inner ceramic/glass enamel coating and 50 mm thick PUF insulation, suitable for maintaining water temperature between 60°C to 80°C, including 3 KW electrical backup with suitable size copper sub-main wiring, thermostat control, 20 mm dia copper pipe connection from collector to tank, active (forced circulation) pressurised type system with necessary pump, controller, sensors, valves, fittings, supports and accessories complete as required and directed.Note:-The complete system shall comply with applicable BIS/MNRE specifications. Contractor shall provide 5 years warranty on solar collector and storage tank without any extra cost. |
| 120 | S&F rotational mouled plythylene water storage tank 250 Ltrs (Cylindrical vertical with top) hoisted and fixed is position with all connected item like as elbow, Tee, socket, PTMT High-Pressured Ball Valve (ISI Marked) all at site reuirement specified in SSR Part-I. |
| 121 | S&F 3-layer PP-R polyypropylene random Copolymer) concealed pipes outer dia 32 mm SDR 7.4 (PN16) UV stabilized and antimicrobial fusion welded having therrmalstability for hot and cold water supply including all PP-R plain & brass threaded polypropylene random fittings fixed complete to walls, ceiling or in floor etc. |
| 122 | S&F Hot water pipe 3 layer (PP-R polypropylene random copolymer) Pipe Outer dia 20mm pipe duly insulted with glass wool and aluminium cladding 20 mm bore pipe. |
| 123 | Supply and fixing for Bib tap for 20 mm bore dia pipe, heavy duty polished bright cast copper alloy fancy type chromium plated (ISI Marked) confirming to IS-781 withh crutch handle screwed down for iron pipe with brass furrele complete all as specified and as directed |
| 124 | S&F freestanding 4-legged steel structure made of MS angle iron or ISMC channels, designed to safety hold a 250 Ltrs ttank at a minimum height of 1.5 meters (from ground to base of tank) for create sufficient gravitty pressure head (~1 bar) to feed water efficiently into solar collectors in a 100 KLD solar water heating system. Note : Hight of stand 1.5 meter (from ground to tank bottom Base Size Platform Size 900 mm x 900 mm (to support 250 L tank) MS Angle 50x50x6 mm (4 pcs) with M16 anchor bolts (4 legs) Paint Red oxide primer + 2 coats enamel anti-rust paint and with MS Flat: 40x6 mm (for base breacing). MS Plate: 6mm thick for top base |
| 125 | Note:-The accepted amount will be arrived after deducting the Sch of credit i.e. Rs 34,542.60 and any other reduction if any from quoted amount. |
| 126 | 500.0 |
| 127 | 400.0 |
| 128 | 200.0 |
| 129 | 200.0 |
| 130 | 450.0 |
| 131 | 250.0 |
| 132 | 3000.0 |
| 133 | 50.0 34542.6 Please Enable Macros to View BoQ information |
AI Tender Summary
Tender Timeline
Aug 06, 2026
11:30 IST
Tender Published
Tender notice published.
Completed
Aug 06, 2026
18:00 IST
Corrigendum-1 Issued
Clarifications on tender conditions and amendments issued.
Completed
Aug 13, 2026
18:00 IST
Corrigendum-2 Issued
Clarifications on tender conditions and amendments issued.
Upcoming · 6 days
Aug 20, 2026
18:00 IST
Corrigendum-3 Issued
Clarifications on tender conditions and amendments issued.
Upcoming · 13 daysAug 20, 2026
17:00 IST
Bid Submission Deadline
Online submission via eProcurement portal.
Upcoming · 13 daysAug 22, 2026
Bid Opening Date
Technical bids will be opened and evaluated.
Upcoming · 15 daysTender Documents
Download All (ZIP) ↓
Disclaimer
We takes all possible care for accurate & authentic tender information. However users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender