Tender For Repair And Maintenance Of Central Heating System And Hot Water Plants And Connected Works At Sk Uk, Rockfall And Tyakshi Area Under Ge 873 Ews
Tender Value
35 Lakhs
Estimated cost
Bid Submission
01 Aug 2026
19 days left
EMD
70000
Bank guarantee accepted
Document Fee
500
Non-refundable
Tender Type
Online
Tender Overview
Organization
Tender ID
Competition Type
NCB
Bidding Type
Tender
Location / State
leh → Jammu and Kashmir
EMD Exemption
Available
Quantity
Not Available
Website
Contact Person
Address
Project Description
Tender for Repair And Maintenance Of Central Heating System And Hot Water Plants And Connected Works At Sk Uk, Rockfall And Tyakshi Area Under Ge 873 Ews
BOQ
| Sl. No. | Item Description |
| 1 | Material and labour for servicing and maintenance of HOT Water Generator outlet by removing accumulated soot from smoke exhaust Chimney, outlet pipe line, removal of carbon by scraping out and washing with scalent and acid/kerosene oil etc. and removing of carbon waste carbonized materials and disposal of fume waste after every 500 Hrs of operation including re-assembling of all the dismantled component to its original position and ensuring smooth functioning of chimney complete all as specified and/ or as directed by Engr-in-Charge. |
| 2 | Material and labour for dismantling oil fired hot water generator of 1.5 Lakh K.Cal/hour capacity any model/ make, unscrewing and removal of boiler side/end plates, taking out burner, CHS control panel, cleaning drum and hot water coil with scalent de-carbonizing, scraping out carbon, dirt accumulated in drum and across coil, overhauling, servicing incl re- assembling all the dismantled component to its original position with testing and commissioning, complete all as specified and/ or as directed by Engr-in-Charge. |
| 3 | Supply and fix in replacement of Heat Tracing cable (heating element) suitable for hot water supply pipe line complete all as specified and/ or as directed by Engr-in-Charge. |
| 4 | Material and labour for dismantling oil fired hot water generator of 0.25 Lakh K.Cal/hour (Boiler) capacity any model/ make, unscrewing and removal of boiler side/end plates, taking out burner, CHS control panel, cleaning drum and hot water coil with scalent de-carbonizing, scraping out carbon, dirt accumulated in drum and across coil, overhauling, servicing incl re- assembling all the dismantled component to its original position with testing and commissioning, complete all as specified and/ or as directed by Engr-in-Charge. |
| 5 | Material and labour for disconnecting and taking up/down CHS pump set of 3 to 7.5 HP of any type from foundation and transporting to authorized workshop, carry out repairs such as replacement of pump bearing and overhauling including replacement of minor unserviceable components/spares like 'O' rings, Oil seal, shaft bush, gland packing, casing ring, gasket packing and greasing, welding, metaling, turning, polishing, Lathe work etc. along with replacement of major components/spares as per manufactures instruction and testing after repairing and reconnecting at site including re-commissioning and testing to ensure efficient and smooth functioning to achieve desired discharge of pump set etc complete all as specified and directed.Note:- Defective major components/spares if required shall be measured as supply only under respective item 5.01 to 5.04 here-in-after and labour element included in this item for replacement. |
| 6 | Supply only of high carbon steel pump shaft as per existing shaft sample. |
| 7 | Supply only stainless steel ball bearing as per existing sample. |
| 8 | Supply only impeller with impeller key as per existing sample |
| 9 | Supply only Mechanical seal as per sample for centrifugal pump |
| 10 | Supply and fix in replacement air release key as per sample for centrifugal pump complete all as specified and/ or as directed by Engr-in-Charge. |
| 11 | Supply and fix in replacement nut, bolt and washer as per sample for centrifugal pump set complete all as specified and/ or as directed by Engr-in-Charge. |
| 12 | Rewinding of 3 phase electric motor of 3 to 7.5 HP with super enameled copper winding wire of same gauge including impregnated paper, sleeves, lathorised fibre glass, varnish and tape, etc. refixing motor at its own position after rewinding and testing the motor at site on full load complete all as specified and/ or as directed by Engr-in-Charge. |
| 13 | Material and labour for disconnecting and removal of burner assembly, servicing, cleaning of burner for de-carbonized/deposited on combustion tank/blast tube with cleaning acid scalent and fixing of burner nozzle for smooth functioning and re-assembling burner and fixed to its original position with testing, complete all as specified and/ or as directed by Engr-in-Charge. Note:- Defective major components/spares if required shall be measured as supply only under respective item 7.01 to 7.10 here-in-after and labour element included in this item for replacement |
| 14 | Supply only burner nozzle jet suitable for burner. |
| 15 | Supply only photocell suitable for burner. |
| 16 | Supply only fuel pump suitable for burner. |
| 17 | Supply only flexible metal fuel pipe line suitable for plant. |
| 18 | Supply only fuel filter. |
| 19 | Supply only magnetic lead (Electrode). |
| 20 | Supply only time relay suitable for CHS burner assembly |
| 21 | Supply only contactor 10 to 15 Amp. |
| 22 | Supply only Normally open and Normally close switch. |
| 23 | Supply only fuel Ignition transformer suitable for burner. |
| 24 | Material and labour for taking down carefully by disconnecting and removing fan coil units of different sizes from hot water circulation line for cleaning with scalent remove the scale and dirt accumulated in copper tube, cleaning the filter, fins and cleaning of radiator parts of FCU and welding /brazing whereever necessary and arrest the leakage in the copper tubing with welding/brazing of the body incl re-assembling and connect the same to its original position, testing complete for smooth flow of water, complete all as specified and/or as directed by Engr-in-Charge. Note:- Defective major components/spares if required shall be measured as supply only under respective item 8.01 to 8.06 here-in-after and labour element included in this item for replacement. |
| 25 | Supply only blower motor as per existing sample |
| 26 | Supply only PCB board as per existing sample |
| 27 | Supply only fan blower motor as per existing sample |
| 28 | Supply only Relay as per existing sample |
| 29 | Supply only LED Display as per existing sample |
| 30 | Supply only capacitor as per existing sample Please Enable Macros to View BoQ information |
| 31 | Supply only capacitor as per existing sample Please Enable Macros to View BoQ information |
AI Tender Summary
Tender Timeline
Jul 11, 2026
11:30 IST
Tender Published
Tender notice published.
CompletedAug 01, 2026
17:00 IST
Bid Submission Deadline
Online submission via eProcurement portal.
Upcoming · 19 daysAug 08, 2026
Bid Opening Date
Technical bids will be opened and evaluated.
Upcoming · 26 daysTender Documents
Download All (ZIP) ↓
Disclaimer
We takes all possible care for accurate & authentic tender information. However users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender