Tender For Addnition/Alteration Of Bldg No.T-83 For The Troops At Hq Cif (R) Under Age (I) Cif (R )
Tender Value
9.70 Lakhs
Estimated cost
Bid Submission
31 Jul 2026
18 days left
EMD
19414
Bank guarantee accepted
Document Fee
500
Non-refundable
Tender Type
Online
Tender Overview
Organization
Tender ID
Competition Type
NCB
Bidding Type
Tender
Location / State
Rajouri → Jammu and Kashmir
EMD Exemption
Available
Quantity
Not Available
Website
Contact Person
Address
Project Description
Tender For Addnition/Alteration Of Bldg No.T-83 For The Troops At Hq Cif (R) Under Age (I) Cif (R )
BOQ
| Sl. No. | Item Description |
| 1 | Dismantling plain or corrugated steel sheeting, any gauge, thickness, including Nainital or similar pattern roof coverings. |
| 2 | Supply and fixing Pre- painted galvalume aluminum zinc coating GI based corrugated steel sheet 0.50mm thick of an colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws as specified and directed. |
| 3 | S & F plain galvalume aluminium zinc coating GI based plain steel sheet 0.50mm thick in ridges, hips, valley gutters at the external end slope of any colour having tansile strength 550 Mpa as in roof(ridges) covering fixed with self tapping screws and caps etc. |
| 4 | S & F rolled mild steel work in tubular trusses, vertical posts, rafters, purlins etc. including special shaped etc complete using ERW or induction butt welded tubes conforming to Gde St-240 and painted one shop coat of zinc chromate primer paint (including preparation of surface) at contractor's workshop before fabrication complete all as specified and directed. |
| 5 | S & F mild steel work as in wind ties for roof including all necessary drilling, bolting or riveting, etc.,and similar work confirming to Fe-290 Gde E-165 complete all as specified and directed. |
| 6 | Preparation of new steel surfaces of any description, not otherwise described over 10cm width or girth and applying two coats of synthetic enamel painting over a coat of red oxide primer complete all as specified and as directed by Engr-in-charge. |
| 7 | M & L for preparation of old painted steel surfaces of any description, over 10 cm width or girth, not other wise described and applying one coat of synthetic enamel paint complete all as specified and directed. |
| 8 | Demolition of cement concrete (unreinforced) in ground floor, paving not exc. 15 cm thickness (below or above ground level) complete all as specified and directed |
| 9 | Dismantling floor, hearth or wall tilling including cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish off the premises. |
| 10 | 25 mm thick PCC 1:2:4 type B-0 (using 12.50 mm graded crushed stone aggregate) as in sub base for laying floor finishes complete all as specified and directed. |
| 11 | Screed bed or bedding layer of mortar 10 mm thick in cement mortar 1:4 for laying floor finishes complete all as specified and directed. |
| 12 | M&L for Non-skid coloured ceramic tiles (square/rectangular) 7 to 8 mm thick, area of each tile exc 0.18 sqm but not exc 0.38 sqm as in floors, set and jointed in neat cement slurry and pointed in white or coloured cement to match the surface,complete all as specified and directed. |
| 13 | M & L for 50 mm thick cement concrete 1:3:6 type C 2 (40 mm graded aggregate ) as in plinth protection, finished even and smooth without using extra cement complete all as specified and directed |
| 14 | Taking down chowkhat or frames with shutters (without taking off shutters from the frames) not exceeding 1.5 Sqm each including cutting holes for taking out hold fasts, dismantling brick work (holes cut and any other damages to jambs, walls for taking out hold fast shall be finished identical to existing finish without any extra cost) complete all as specified and directed. |
| 15 | All as per ser item No 14 above but exceeding 1.50 Sqm and not exceeding 4.00 Sqm complete all as specified and directed. |
| 16 | Pressed steel frames for doors with one or more rebates including necessary supply and fixing lugs, hinges, lock strike plate etc. complete, of frame size 105 x 60 mm, including one shop coat of red oxide zinc chrome primer complete all as specified and directed. |
| 17 | S&F 35 mm thick plain framed panelled door shutters of 2nd class hard wood (Factory made) two panel with lock rail and panel of 9mm thick BWP commercial ply or 12mm veneered particle board with commercial veneering on both faces. The size of rail and stile as per IS : 1003 Part-I, Kiln seasoned and chemically pressure treated, fitted to chowkats complete all as specified and directed. |
| 18 | S&F 35 mm thick 2nd class hard wood plain framed factory made glazed and skelton shutters open rebated and prepared to receive glass/ wire gauge etc (without sas bars)edges of framing plain, chamfered or rounded, fitted with cut and mitred beads for secring glass,etc size of members of shuters as specified in SSR Part-I,Section 8, clause 8.24 (a); supply and fitted to chowkhats, all as specified. |
| 19 | Mild steel sliding door bolt plate type 250 mm long stove enameled black with bright bolt not less 12 mm dia bolt with and including a minimum of 6 bolts and nuts, four on bolt plate and two on staple plate complete all as specified and directed. |
| 20 | Aluminum anodised barrel tower bolts of extruded section with 150 mm long bolt complete all as specified and directed. |
| 21 | Aluminum handles cast type, anodised, 150 mm size complete all as specified and directed. |
| 22 | Mild steel cold rolled butt hinges medium weight 100 mm long fixed to pressed steel door frame if required complete all as specified and directed. |
| 23 | S & F in repair300 mm M S rat tail rod pattern including roller and roller plate fixed to wooden or steel frames with welding etc. complete all as specified and directed. |
| 24 | Steel window (Box type) factory made with side hung shutters including pintol hinges, steel handles, steel peg stay and all locking arrangement complete with glazing bars dovetailed or welded including one shop coat of red oxide primer complete all as specified and directed.Note : (i) The window shall be fabricated as per Drg CEUZ/TD/1269/2008 Sh 1/3. (ii) MS fillets, glazing, wire gauge shall be measured and paid separately. |
| 25 | All as per ser item No 24 here in before but without glazing bar complete all as specified and directed. |
| 26 | Mild steel framed work such as grills, gratings, etc. with ends of bars shouldered and/or riveted or forged into spikes, framed guard bar; barred iron doors; ladder; framed balusters; railing;frame work for water tanks,cup Board etc and similar work conforming to Fe 290 Gd E-165 complete all as specified. |
| 27 | Galvanised mild steel wire cloth, 0.56 mm nominal dia wire and average width of aperture 1.18 mm and fixed with tinned tacks or galvanised wire staple complete all as specified and directed. |
| 28 | 3 mm thick sheet glass ordinary quality and glazing with oil putty or wooden beads in squares not exceeding 0.50 Sqm in each pane complete all as specified and directed. |
| 29 | M&L for preparation of wooden surfaces exceeding 10 cms width or girth and applying two coats of synthetic enamel paint over one coat of pink primer complete all as specified. |
| 30 | S&F, solid PVC Wall panelling/lining consisting of 5mm thick wood grain printed colour PVC sheet as in striups and chanel inclusive of solvent cement and fixing at site on necessary pvc wooden frame incl fillets as per specifications and drawings |
| 31 | M&L for sand cushioning under floors including watering and consolidation . complete all as specified and as directed. |
| 32 | S& F coloured machine vibro mechenically floated glossy finish interlocking cement paver block,any shape and size confirming to IS 15658-2006 of 60mm thickness,M-35 Grade with,topping of cement mixed with imported pigment,colour and shape shall be approved by engr-in-charge ISI Marked. |
| 33 | M & L for PCC type C 2 1:3:6 (20mm graded stone aggregate) as in surface channels and drains etc incl.necessary form works. |
| 34 | Extra for forming fair finished drain or channel 45 cm inner girth in cement concrete using extra cement including forms, moulds, mitred/ stop ends etc complete all as speicified and directed by Engr-in-Charge |
| 35 | Taking down carefully copper/aluminium point wiring (light,fan,bell, socket or power) complete,including fixtures and fittings such as switches, ceiling roses, holders,regulators, sockets, tube light fittings and including making good the disturbed surfaces to match with existing surface and colour shade with putty and white cement for smooth finishing of holes,small patches etc complete all as specified and directed . Please Enable Macros to View BoQ information |
| 36 | Taking down carefully copper/aluminium point wiring (light,fan,bell, socket or power) complete,including fixtures and fittings such as switches, ceiling roses, holders,regulators, sockets, tube light fittings and including making good the disturbed surfaces to match with existing surface and colour shade with putty and white cement for smooth finishing of holes,small patches etc complete all as specified and directed . Please Enable Macros to View BoQ information |
AI Tender Summary
Tender Timeline
Jul 10, 2026
11:30 IST
Tender Published
Tender notice published.
CompletedJul 31, 2026
17:00 IST
Bid Submission Deadline
Online submission via eProcurement portal.
Upcoming · 18 daysAug 07, 2026
Bid Opening Date
Technical bids will be opened and evaluated.
Upcoming · 25 daysTender Documents
Download All (ZIP) ↓
Disclaimer
We takes all possible care for accurate & authentic tender information. However users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender