Tender For Addition Alteration To Kitchen Of Bldg No P-554, Special Repairs To Bldg No T-45 (Rr Mt) Of 3 Cesr, Addn/Altn To Drainage Sys In Near/ Adjacent Of Main Gate To Culvert Near Spear Top Of 3 Cesr And Addn/Altn To Drainage Sys Of 3 Cesr At Rms
Tender Value
46 Lakhs
Estimated cost
Bid Submission
31 Jul 2026
17 days left
EMD
92000
Bank guarantee accepted
Document Fee
500
Non-refundable
Tender Type
Online
Tender Overview
Organization
Tender ID
Competition Type
NCB
Bidding Type
Tender
Location / State
Wokha → Nagaland
EMD Exemption
Not Available
Quantity
Not Available
Website
Contact Person
Address
Project Description
Tender For Addition Alteration To Kitchen Of Bldg No P-554, Special Repairs To Bldg No T-45 (Rr Mt) Of 3 Cesr, Addn/Altn To Drainage Sys In Near/ Adjacent Of Main Gate To Culvert Near Spear Top Of 3 Cesr And Addn/Altn To Drainage Sys Of 3 Cesr At Rms
BOQ
| Sl. No. | Item Description |
| 1 | S&F in repairs pre-painted galvalume aluminum zinc coating GI based corrugated trapezoidal steel sheet 0.50mm thick of an colour having tensile strength of 550 Mpa as in roof covering /cladding to wall, fixed with self tapping screws complete all as specified and as directed. |
| 2 | S&F in repairs pre-painted galvalume aluminum zinc coating GI based Plain steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws complete all as specified and as directed. |
| 3 | S&F steel work in tubular trusses, post, purlins including special shaped washer etc. Complete using ERW or induction butt welded tubes conforming to IS 1161-1979 grade st-240 including dismantling of old iron or mild steel work from its position of any description complete all as specified and as directed. |
| 4 | S & F 2nd class hard wood scantling as in framed work etc clean sawn complete including dismantling of old one from its position all as specified and directed. |
| 5 | S & F second class hardwood weather boarding, clean sawn, plain, 20 mm thick or feather edged 15 mm to 20mm thick and fixed with 30mm laps complete all as specified and as directed. |
| 6 | M&L for 15mm thick plastering in CM (1:4) on one side of lathing in two separate layers finished even and smooth without using extra cement and surfaces finished even and smooth (without using extra cement) including demolition of reed, lathing single or double, including battens and plaster or chicken wire lathing with and including provision of GI wire netting 0.71 mm dia and 12 mm mesh lathing in to reed in walls incl all laps cutting and waste complete all as specified and as directed. |
| 7 | Taking down plastering on lathing (other than wire-netting), without removing lathing, in Cement mortar (one side only measured in cases where both sides are plastered) |
| 8 | M&L for Rendering 15 mm thk in CM 1:4 on stone masonry surfaces or surface other than fair face of brick-work or on one side of lathing finished fair and even without using extra cement complete all as specified and as directed. |
| 9 | M&L for rendering 12 mm thick in CM (1:6) on other side of lathing finished even and smooth without using extra cement complete all as specified and as directed. |
| 10 | M&L for brick work with sub class `B' bricks(using old size burnt bricks) straight or curved on plan exc 6m mean radius built in CM (1:6) including demolition of old brick work from its position complete all as specified and as directed. |
| 11 | M&L for brick work with sub class `B' bricks (using old size burnt bricks) straight or curved on plan to any radius in half brick thick walls built in CM (1:4) including demolition of old brick work from its position complete all as specified and as directed. |
| 12 | M&L for Rendering 15 mm thk in CM (1:6) on fair face of brick-work or concrete surface to be finished fair and even without using extra cement complete all as specified and as directed. |
| 13 | M&L for Rendering 15 mm thick in CM (1:4) other than fair face of brick-work , finished the surfaces fair and even without using extra cement complete all as specified and as directed. |
| 14 | M&L for Rendering 10mm thick in CM (1:6) on other than fair face brick work/concrete surfaces finished even and fair without using extra cement including taking down old plaster from its positions complete all as specified and as directed. |
| 15 | M&L for 1.5 mm thick Birla white putty/JK white wall care putty on walls complete all as specified and as directed. |
| 16 | M&L for applying two coats of oil bound distemper on old plastered surfaces of walls including preparation of surface complete all as specified and as directed. |
| 17 | M&L for preparation of new plastered or un plastered surface of walls including cornices, pilasters etc and applying two coats of cement base paint over and including a coat of primer of approved shade on walls complete all as specified and as directed. |
| 18 | M&L for preparation of old plastered surface of walls including cornices, pilasters etc and applying two coats of cement base paint over and including a coat of primer of approved shade on walls complete all as specified and as directed. |
| 19 | M&L for preparation of new plastered or un plastered surface of walls and applying two coats of oil bound distemper over and including a coat of primer of approved shade on walls complete all as specified and as directed. |
| 20 | M&L for applying two coats of oil bound distemper over and including a coat of primer of approved shade on old plastered surfaces of walls including preparation of surface complete all as specified and directed. |
| 21 | M&L for preparation of new surfaces of steel and iron work of any description over 10 cm width or girth not otherwise described and applying two coats of synthetic enamel paint over and including a coat of redoxide primer on new surfaces in any tint complete all as specified and as directed. |
| 22 | M&L for preparation of new untreated wooden surfaces of any description not otherwise described over 10 cm width or girth and applying two coats of synthetic enamel paint over a coat of pink wood primer complete all as specified and as directed. |
| 23 | M&L for preparation of old Wood work of any description over 10 cm width or girth not otherwise described and but applying two coats of synthetic enamel paint over a coat of pink wood primer on new surfaces |
| 24 | Taking down chowkhat or frames exc 1.5 Sqm but not exc 4 Sqm each (without taking off shutter from the frame) complete all as specified and as directed. |
| 25 | Taking down chowkhat or frames not exc 1.5 Sqm each (without taking off shutter from the frame) complete all as specified and as directed. |
| 26 | S&F factory made 30mm thick, flush shutters, solid core construction, with particle board core and plywood face panels complete all as specified and as directed. |
| 27 | S&F factory made second class hardwood glazed and skeleton window and ventilator shutters, 30mm thick, open rebated and prepared to receive glass, gauze, etc. (without sash bars), edge of framing plain, chamfered or rounded, fitted with cut and mitred beeds for securing glass etc.; sizes of members of shutters as specified in SSR Part I, Section 8. clause 8.20 (b); supplied and fitted to chowkats complete all as specified and as directed. |
| 28 | S&F sheet glass 3mm thick ordinary quality, pin headed type and glazing with oil putty or wooden beads not exceeding 0.5 Sqm in each pane complete all as specified and as directed. |
| 29 | S&F mild steel wire cloth, 0.56mm nominal dia of wire and average width of aperture 1.18mm, fixed with tinned tacks or galvanized wire staples complete all as specified and as directed. |
| 30 | Demolition, Cement concrete of any description and in any position not otherwise specifically provided for complete all as specified and as directed by the Engineer-in-Charge. |
| 31 | M&L for 75 mm thick PCC (1:3:6) type C-2 , (using 40 mm graded stone aggregate) in plinth protection/aprons/path laid to slope of 1:12, finished fair and even without using extra cement with and including all necessary formwork to divide the area in panels, finishing exposed edges fair or rounding or chamfering where directed and providing 10 mm wide joints throughout thickness of plinth protection duly filled with mastic filling (one part of hot bitumen 85/25 and three part of fine sand by weight) complete all as specified and as directed. |
| 32 | M&L for PCC (1:3:6) type C-2, 75 mm thick (using 40mm graded stone agg) as in sub base complete all as specified and as directed. |
| 33 | M&L for machine pressed precast concrete interlocking paver block any shape & size conforming to IS15658-2006 of 80mm thickness M-40 grade using grey cement & pigment laid over and including 50 mm thick sand cushioning including watering and consolidation for laying interlocking blocks etc complete all as specified and as directed. |
| 34 | Dismantling floor, hearth or wall tiling including cement mortar bedding (including backing), removing serviceable tiles to store and rubbish off the premises complete all as specified and directed. |
| 35 | M&L for PCC (1:4:8) type D-2, 75 mm thick (using 40mm graded stone agg) as in sub base complete all as specified and as directed. |
| 36 | S&F 100 size stainless steel butt hinges complete all as specified and directed. |
| 37 | S&F 150 mm Aluminium handles, cast type, anodised complete all as specified and directed. |
| 38 | S&F 150 mm Aluminium, anodised, barrel tower bolts of extruded section and fixed complete all as specified and directed. |
| 39 | S&F in repairs GI tubes medium grade, galvanised wih all fittings and fixed complete to walls and ceiling or laid on floors etc, 15 mm bore complete all as specified and as directed. |
| 40 | S&F in repairs GI tubes medium grade, galvanised wih all fittings and fixed complete to walls and ceiling or laid on floors etc, 20 mm bore complete all as specified and as directed. |
| 41 | M&L for precast cement concrete type B-1 (1:2:4) (Using 20 mm graded stone aggregate) as in cover slabs, manhole cover, chamber cover and drainge cover set in cement mortar (1:6) including necessary formwok including demolition of old reinforced concrete complete all as specified and as directed. |
| 42 | M&L for TMT bars, 6 mmdia upto 10mm dia,as in reinforcement, cut to length, bent to shape required including cranking,bending spirally for hooping for column, hooking ends and binding with and incl MS wire(annealed) not less than 0.9 mm dia complete all as specified and as directed. |
| 43 | M&L for 20mm thick Granite Z black in colour (of any type) work (table rubbed and mirror polished) in steps, jambs, pillars, window cills, cooking platforms, laid over and including 20mm thick screed bed/bedding layer in cement mortar (1:4) and pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite including demolition of old tiles/slab including cement mortar bedding of any description complete all as specified and as directed. |
| 44 | Dismantling, floor, hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish off the premises |
| 45 | M&L for Non Skid coloured ceramic tiles 7 to 8 mm thick (square/ rectangular) area of each tile exceeding 0.18 Sqm but not exceeding 0.38 Sqm, in floors laid over and including 15mm thick screed bed for laying floor finishes in CM (1:6) set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tiles complete all as specified and as directed. |
| 46 | M&L for dark Vitrified Ceramic tiles , (8-9) mm thick (square/ rectangular) polished,area of each tiles n exc 0.36sqm , set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tiles over and including backing coat of 10 mm thick in CM (1:4) complete all as specified and as directed. complete all as specified and as directed. |
| 47 | M&L for providing Machine cut ,mirror polished kota stone slab 20-25mm thick over and including 10mm thick baking coat in CM (1:4) on vertical surfaces , in risers of steps,skirting, dados, and pillar and jointed with grey cement slurry mixed with pigment to match the shade of the stone slab including rubbing and polishing including demolition of old tiles/slab including cement mortar bedding of any description complete all as specified and as directed. |
| 48 | S&F in repairs Stainless steel wire cloth. 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire staples |
| 49 | Mirror polishing on marble/ granite/ Kota stone/ stone work where ever required to give high gloss finish complete all as specified and as directed. |
| 50 | Demolition of brick work or stone/boulder masonry, built in cement mortar including all quions, arches, pillers etc complete all as specified and as directed. |
| 51 | M&L for brick work with sub class `B' bricks (using old size burnt bricks) straight or curved on plan to any radius in half brick thick walls built in CM (1:4) complete all as specified and as directed. |
| 52 | M&L for Anti termite treatment of soil under existing floors using emulsion @ one litre per hole, 300mm apart ncluding drilling and plugging 12mm dia holes with cement mortar 1:2 (1 cement: 2 coarse and) to match the existing floors complete all as specified and as directed. |
| 53 | M&L for Anti termite treatment at points of contact of wood work by chemical emulsion (in oil or kerosene based solution) @ 0.5 litre/hole by drilling 6mm dia holes at a downward angle of 45 degree at 150mm centre to centre and sealing the same complete all as specified and as directed. |
| 54 | S&F sinks made of stainless steel 1mm thick kitchen or laboratory with plugs, washers and waste pipe; including bedding in cement mortar on to dwarf wall or including fixing cantilever brackets and connecting union to pipe, overall size not less than 495mm x 420mm bowl size not less than 410mm x 330mm x 160mm complete all as specified and as directed. |
| 55 | M&L for modular kitchen bottom cabinet carcass and shutters (kitchen cabinet ) with width varies from 45 cm to 60 cm and height 60 to 70 cm made of 18 mm thick plain High density PVC foam board interior grade with one side decorative lamination glossy finish & other side plain white (lamination measured separately) as in shelves, sides, back and doors including PVC lipping on all exposed edges of same texture & shade to match that of outer laminate, fitted with selected quality modular type stainless steel hydraulic auto clossing concealed hinges and sliding channels, fancy type 200 mm long stainless steel handles of Make: Hettich,Ebco,Hafle or equivalent as approved by GE, complete all as specified and directed by Engr in change and manufacturer specification. Note: (a) Area shall be measured flat of each member of cubboard (b) Design & layout of cabinate and pattern / colour of laminate to be approved by GE.(c) Laminates, hardwares and fittings will be measured and paid separately. |
| 56 | M&L for modular kitchen overhead cabinet carcass and shutters (kitchen cabinet ) with width varies from 45CM to 60 cm and height 60 to 70 cm made of 18 mm thick plain High density PVC foam board interior grade with one side decorative lamination glossy finish & other side plain white( lamination measured separately) as in shelves, sides, back and doors including PVC lipping on all exposed edges of same texture & shade to match that of outer laminate, fitted with selected quality modular type stainless steel hydraulic auto clossing concealed hinges and sliding channels, fancy type 200 mm long stainless steel handles of Make: Hettich,Ebco,Hafle or equivalent as approved by GE, complete all as specified and directed by Engr in change and manufacturer specification. Note: (a) Area shall be measured flat of each member of cubboard (b) Design & layout of cabinate and pattern / colour of laminate to be approved by GE.(c) Laminates, hardwares and fittings will be measured and paid separately. |
| 57 | M&L for floor standing wall attached Narrow modular kitchen tall pull out pantry cabinet ( Size width 400 mm , depth 300 mm and height 1800 mm) with multiple shelves (8 Nos) with transparent acylic or polycarbonate baskets with metal rims swing or pull out shutters made of 18 mm thick plain High density PVC foam board interior grade with both side lamination 0.9mm thick , including PVC lipping on all exposed edges of same texture & shade to match that of outer laminate, with selected quality modular type stainless steel hydraulic auto clossing concealed hinges handles of Make: Hettich,Ebco,Hafle or equivalent as approved by GE, complete all as specified and directed by Engr in change and manufacturer specification. Note: (a) Area shall be measured flat of each member of cubboard (b) Design & layout of cabinate and pattern / colour of laminate to be approved by GE.(c) Laminates, hardwares and fittings will be measured and paid seperately. |
| 58 | S&F 0.9 mm thick Decorative laminate type 1 of surface finish, colour and pattern as approved, fixed with approved adhesive as per manufacturer's instructions complete all as specified and as directed. |
| 59 | S&F for Stainless Steel (AISI 304 grade ) non magnetic multilayer nickel chrome plated for multipurpose utensils container including frame work , telescopic channels , handles etc as required & complete all as specified and as directed, Note:- Make, Utensils sample , design & pattern of each basket to be approved by GE of following size in each kitchen :- |
| 60 | S&F Kitchen plain basket made out of 4 mm dia Stainless stell wire , C/C spacing 30 mm ,size 536 mm x 500 mm x 100mm of approved make & design complete all as specified and as directed. |
| 61 | S&F Kitchen plain basket made out of 4 mm dia Stainless stell wire , C/C spacing 30 mm, size 536 mm x 500 mm x 150mm of approved make & design complete all as specified and as directed. |
| 62 | S&F Kitchen plate basket made out of 4 mm dia Stainless stell wire , C/C spacing 30 mm, size 536 mm x 500 mm x 200mm of approved make & design complete all as specified and as directed. |
| 63 | S&F PVC Cutlery tray 600 mm of approved make & design complete all as specified and as directed. |
| 64 | S&F stainless steel basket of costomised size for cutlery, cup and saucer of approved make & design complete all as specified and as directed. |
| 65 | S&F stainless steel two shelf bottle rack of sixe 200 mm x 485 mm x 430 mm with external width 200 mm in spice jar, bottles,glass jar etc( Baskets made out of stainless steel 4 mm dia wire 30 mm C/C and fixed to kitchen cupboards with necessary fixing arrangements like auto closed sliding channel make Hettich, Hafele, Ebco or equivalent of approved make & design complete all as specified and as directed. |
| 66 | S&F stainless steel auto closed sliding / telescopic channel of length 500 mm with 3 nos of holding ball of load carrying capcity 45 to 50 kg, width 45 mm including necessary fixing arrangement complete all as specified and directed by Engr in charge. Make: Hettich, Ebco, Hafele or euivalent as approved by GE. |
| 67 | S& F Auto closed cabinet hinges for fixing cabinet shutters complete all as specified and directed by Engr in charge. Make: Hettich, Ebco, Hafele or euivalent as approved by GE. |
| 68 | S&F 150 mm length Fancy handle (Gola profile) in approved colour and design complete all as specified and directed by Engr in charge. Make: Hettich, Ebco, Hafele or euivalent as approved by GE. |
| 69 | S&F 100 mm length Fancy handle (Gola profile) in approved colour and design complete all as specified and directed by Engr in charge. Make: Hettich, Ebco, Hafele or euivalent as approved by GE. |
| 70 | Excavation in trenches not exceeding 1.5 m wide and not exceeding 1.5 m depth and getting out in soft/ loose soil complete all as specified and as directed. |
| 71 | Returning filling in trenches including spreading leveling watering and well ramming in layers not exceeding 25 cm thick all complete all as specified and as directed. |
| 72 | Removing of excavated material not exceeding 50 m and depositing where directed at a level not exceeding 1.5 m above the starting point all complete all as specified and as directed. |
| 73 | M&L for cement concrete type C-2, (1:3:6) (using 40mm graded stone aggregate) as in foundation, filling and mass concrete complete all as specified and as directed. |
| 74 | M&L for brick work with sub class `B' bricks(using old size burnt bricks) straight or curved on plan exc 6m mean radius built in CM (1:4) complete all as specified and as directed. |
| 75 | M&L for cement concrete type B-1(1:2:4) (using 20 mm graded stone aggregate) as in surface channels,drain bed, coping , complete all as specified and as directed. |
| 76 | M&L for Rendring 15mm thick in CM (1:4) on fair faces of brick work, surfaces finished even and fair without using extra cement complete all as specified and as directed. |
| 77 | M&L for Extra for forming fair finished drain or channel 30 cm inner girth in cement concrete using extra cement including forms moulds complete all as specified and as directed. |
| 78 | Add to item No.77(here-in-before) for additional 25mm inner girth or under girth 30cm complete all as specified and as directed. |
| 79 | M&L for PCC (1:2:4), Type B-0,(using 12.5 mm graded stone aggregate) as in Haunching /Benching of drain and manholes complete all as specified and as directed. |
| 80 | M&L for precast factory made manhole cover/ drain covers with plain faces using RCC (1:2:4) type B-1(using 20mm graded stone aggregate) and set in CM (1:4) including formwork etc of required sizes complete all as specified and as directed. |
| 81 | M&L for Point wiring in repairs complete for One light point controlled by one, one way switch with two runs of 1.5 sqmm single core PVC insulated FR-LSH cable 1100 volts grade with multi-stranded copper conductors, drawn through and including PVC double locked Casing & caping including provision of 1.5 sqmm, FR-LSH, PVC insulated copper cable as earth continuity conductor connected to common earth dolly, including PVC rectagular box for mounting switches / sockets / regulators etc. with 3 mm thick plastic laminated sheet cover of suitable size as required at site and 50 mm deep complete all as specified and as directed. |
| 82 | M&L for Point wiring in repairs complete for One 3 pin socket outlet 5 Amps on the same board with two runs of 1.5 sqmm single core PVC insulated FR-LSH cable 1100 volts grade with multi-stranded copper conductors, drawn through and including PVC double locked Casing & caping including provision of 1.5 sqmm, FR-LSH, PVC insulated copper cable as earth continuity conductor connected to common earth dolly, including PVC rectagular box for mounting switches / sockets / regulators etc. with 3 mm thick plastic laminated sheet cover of suitable size as required at site and 50 mm deep complete all as specified and as directed. |
| 83 | S&F Switch Piano, flush type single pole, one way 6 Amps complete all as specified and as directed. |
| 84 | S&F Switch Socket combination, 2 in 1, 3 pin 6A flush type complete all as specified and as directed. |
| 85 | S&F ceiling rose 3 terminal PVC/Polycarbonate isolated body complete all as specified and as directed. |
| 86 | S&F in repairs/replacement 20W LED, 4', Wall mounted LED batten, extruded aluminium heat sink provided for efficient heat dissipation & integrated electronic driver.etc with all accessories internally pre-wired and fixing the same and connecting up with flexible copper cable from ceiling rose to the light fitting complete all as specified and as directed. |
| 87 | Supply , fixing and testing of LED Bldg Security light fitting of capacity 25 Watt 230 V AC outdoor type with high pressure die cast aluminum hosing and heat resistant complete with driver, lamp bracket with impact and corrosion resistant including thermal management in multiple optics complete with IP 65/66 protection complete including 1.2 mtr GI bracket of 25mm bore light grade bent to shape and fixed on wall with metal fastners 2 Nos 10mm dia incl drilling of holes as reqd and connecting up with flexible copper cable of size 0.75 sqmm 3 core from ceiling rose to the light fitting all as specified and directed by Engr-in-Charge. |
| 88 | M&L for sub main wiring in repairs complete with two runs of 1.5 Sq mm and one run of 1.5 Sqmm for earth wire with multi standard copper conductors FRLSH quality, 1100 volts grade, drawn through and including PVC conduit and its accessories of suitable size including making good the disturbed surfaces and paint touch up to match with the existing surface) complete all as specified and as directed. NOTE:- Two runs of 1.5 Sq mm + one run of 1.5 Sq mm and one run of PVC conduit and its accessories of suitable size shall be measured as one unit length. |
| 89 | M&L for sub main wiring in repairs complete with two runs of 4.0 Sq mm and one run of 4.0 Sq mm for earth wire with multi standard copper conductors FRLSH quality, 1100 volts grade, drawn through and including PVC conduit and its accessories of suitable size including making good the disturbed surfaces and paint touch up to match with the existing surface) complete all as specified and as directed. NOTE:- Two runs of 4.0 Sq mm + one run of 4.0 Sq mm and one run of PVC conduit and its accessories of suitable size shall be measured as one unit length. |
| 90 | S&F in repair/ replacement of unsv light fittings of existing high mast with LED energy saving, environmental friendly,LED flood light 120 watt 230 V AC outdoor type with thermal management in multiple optics and equipped with IP66 protection, with impact and corrosion resistant complete with driver and lamp suitable for high mast/tower lights as application including openign and fixing of nuts, bolts and washers on existing high mast/tower/wksp structure properly complete all as specified and as directed. |
| 91 | S&F in repairs MCB Distribution board double door type SPN 8 way, sheet steel, powder painted, with copper bus bar neutral link & earth bar etc. and fixing MCBs of various rating capacity complete all as specified and as directed. |
| 92 | S&F in repairs MCB Distribution board double door type SPN 4 way, sheet steel, powder painted, with copper bus bar neutral link & earth bar etc. and fixing MCBs of various rating capacity complete all as specified and as directed. |
| 93 | S&F in repairs MCB SPN 32 Amp rating 240V, 10KA 'C' curve miniature circuit breaker (MCB) of following poles and current carrying capacity in the MCB DB complete with connection testing and commissioning complete all as specified and as directed. |
| 94 | S&F in repairs MCB SP 5-40 amp rating 240V, 10KA 'C' curve miniature circuit breaker (MCB) of following poles and current carrying capacity in the MCB DB complete with connection testing and commissioning complete all as specified and as directed. |
| 95 | M&L for laying of LT UG cable, XLPE insulated, galvanised steel strip or wire armoured, heavy duty electric cable with aluminium conductor, 1100 volts grade, cross-sectional area of 6 sq mm, 2 core including taking out old unsv cable complete all as specified and as directed. NOTE :- (i) Excavation and earth work, sand cushioning, cable protection cover, pipe etc. shall be measured and paid seperately under relevant items. |
| 96 | M&L for spread fine river sand in trenches complete all as specified ans as directed. Note: Punned thickness shall be measured and paid. |
| 97 | M&L for laying brick sub class 'B' old size burnt bricks for cable protection of size 230mmx115mmx75mm complete all as specified and as directed |
| 98 | Supply & laying tubes 'light grade' galvanised, with all fittings, fixed complete to walls, poles, ceilings for protection of cables of size 32 mm dia bore including taking out unsv GI tubing complete all as specified and as directed. |
| 99 | M&L for earthing complete with galvanized steel earth plate electrode of size 600x600x6mm thick buried directly in ground (earth pit not less than 2.25m deep below the normal ground level) with top edge of the earth plate not less than 1.5 mtr below normal ground level connected to galvanised earth lead wire 4 mm dia as earth lead connectd by means of bolts, nuts, washers and check nuts all as shown in electrical plate No 3 of MES SSR Part-I, including testing on completion complete all as specified and as directed. NOTE:- (i) The unit rate shall also included for earth work in hard/ dense soil, PCC (1:3:6) type C1 chamber, CI frame with CI cover funnel with GI watering pipe 20mm dia Medium grade, GI protection pipe light grade 15mm dia and wire mesh complete in addition to item No 1 (a) to (e) of preamble (notes) under sub heading earthing, specified on Sl Page No 441 of MES SSR Part-II. (ii) Earthing lead and GI protection pipe beyond 7.5m will be measured and paid separately. Please Enable Macros to View BoQ information |
AI Tender Summary
Tender Timeline
Jul 10, 2026
11:30 IST
Tender Published
Tender notice published.
CompletedJul 31, 2026
17:00 IST
Bid Submission Deadline
Online submission via eProcurement portal.
Upcoming · 17 daysAug 03, 2026
Bid Opening Date
Technical bids will be opened and evaluated.
Upcoming · 20 daysTender Documents
Download All (ZIP) ↓
Disclaimer
We takes all possible care for accurate & authentic tender information. However users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender