Tender For Construction Of Judicial Court Complex At Dehra,Tehsil Dehra Distt. Kangra (H.P.) Under Centrally Sponsored Scheme For The Development For Infrastructure Facility For Judiciary.(Sh:- Construction of 3 Nos Court Halls(1 No. For Adj & 2 Nos
Tender Value
36.39 Lakhs
Estimated cost
Bid Submission
17 Jul 2026
5 days left
EMD
72800
Bank guarantee accepted
Document Fee
2000
Non-refundable
Tender Type
Online
Tender Overview
Organization
Tender ID
Competition Type
NCB
Bidding Type
Tender
Location / State
Kangra → Himachal Pradesh
EMD Exemption
Not Available
Quantity
Not Available
Website
Contact Person
Address
Project Description
Tender for Construction Of Judicial Court Complex At Dehra,Tehsil Dehra Distt. Kangra (H.P.) Under Centrally Sponsored Scheme For The Development For Infrastructure Facility For Judiciary.(Sh:- Construction of 3 Nos Court Halls(1 No. For Adj & 2 Nos For Civil Judge )(Sh:-Providing Fire Fighting System Therein)
BOQ
| Sl. No. | Item Description |
| 1 | Providing, fixing, testing and commissioning of MS air cushion tank on top of each riser fabricated form 6mm thick MS plate, 250mm in diameter and 1.2 m in height with dished ends fabricated from 8mm thick MS plate with Air release valve with stop cock, flanged inlet connection and drain arrangement with 25mm dia valve, pressure gauge with gun metal stop cock complete with all accessories as required in all respect and to the best satisfaction of Engineer-in-Charge.Makes:- Fabricated item. |
| 2 | Providing, fixing, testing and commissioning of Perched air vessel (size 450 mm dia & 2000 mm height) for pressurization of hydrant / sprinkler system complete with adequate pressure switches (as per design / requirement) with valves to operate as per operating sequences including 25 mm dia drain valve, air release valve with stop cock on the top, minimum 50 mm dia inlet with isolating valve duly painted from inside and outside with two coats of synthetic enamel paint over a coat of primer complete as required and Suitable cement concrete foundation with plaster, along with all neccessory floor supporting stand and foundation arrangement.(Vessel should be suitable for rated working pressure) as required complete in all respects and to the best satisfaction of Engineer-in-charge. |
| 3 | Makes:- Fabricated item. |
| 4 | Providing, laying, jointing, testing and commissioning of following sizes of MS 'C' Class (Heavy duty) pipes conforming to IS-1239 with all fittings (standard MS fitting with welded joint shall be used on the pipes) including tees, elbows, reducers, union, flanges, rubber gaskets, GI nuts bolts, washer including supporting/fixing the pipe on floor / wall /ceiling with clamps, hangers (using anchor fastners) as per specification. including cutting holes and chases in brick, RCC work and making good the same to original conditions complete in all respects. All hangers, clamps, brackets etc. shall be of iron unless specified otherwire and then supply of the same shall also be included for rates under this head. Welding of any kind on the galvanized support / hanger shall not be permitted including synthetic enamel paint of approved shade over a coat of zinc primer.Priorto application of primer the surface should be cleaned dirt,rusts,rough substance etc. as required complete in all respects and to the best satisfaction of Engineer-in-charge. |
| 5 | 25mm dia pipe |
| 6 | 80mm dia pipe |
| 7 | 100 mm dia pipe |
| 8 | 150 mm dia pipe |
| 9 | 200 mm dia. Pipe |
| 10 | Makes:- Jindal/Tata./Surya Tube. |
| 11 | Providing two coats of synthetic enamel paint of approved shade over a coat of primer. Prior to application of primer the surface should be cleaned for any dirt, rusts, rough substance etc. Including painting of legends both direction arrow as per the approval of the Project Manager as required complete in all respects and to the best satisfaction of Engineer-in-charge. |
| 12 | 25mm dia pipe |
| 13 | 80 mm dia pipe |
| 14 | 100mm dia pipe |
| 15 | 150mm dia pipe |
| 16 | 200 mm dia pipe |
| 17 | Providing & Fixing of burden type Stainless Steel dial type pressure gauge with brass isolation valve and pipe of 100 mm dia with Caliberation: 0-20 Kg/cm2 as required complete in all respects and to the best satisfaction of Engineer-in-charge. |
| 18 | Make:- H Guru, Bell, Fiebig |
| 19 | Providing & fixing stainless steel fire hydrant single headed landing valve with 80 mm N.B. flanged inlet, s.s spindle controlled 63 mm dia female instantaneous outlet type. SS coupling, blank cap, chain, twist release type lug & all accessories Conforming to IS standards as required complete in all respects and to the best satisfaction of Engineer-in-charge. |
| 20 | Make: Minimax/OMEX/ Padmini |
| 21 | Providing & Fixing of 63 mm dia 15 m long non-percolating flexible hose (RRL- type A) as per IS : 636. Type A with stainless steel male & female instantaneous type coupling (IS 903) (For internal and External hydrant system) as required complete in all respects and to the best satisfaction of Engineer-in-charge. |
| 22 | Make: Minimax/OMEX/ Padmini |
| 23 | Providing and Fixingstainless steel 63 mm dia instantaneous pattern branch short pipe, 20 mm dia nozzle conforming to IS 903, suitable for inter connection to hose pipe coupling as required complete in all respects and to the best satisfaction of Engineer-in-charge. |
| 24 | Make: Minimax/OMEX/ Padmini |
| 25 | Providing & fixing ball valve 25mm dia. as required complete in all respects and to the best satisfaction of Engineer-in-charge. |
| 26 | Make: Sant/Zoloto/Audico. |
| 27 | Providing & fixing of Bitumein sheet 4mm thick (pipekot) wraping & coating for underground pipe150 mm dia. as required complete in all respects and to the best satisfaction of Engineer-in-charge. |
| 28 | Make Shalimar/WTL or equivalent |
| 29 | Providing & Fixing of wall mounting swinging type first aid fire hose reel with drum, hanging bracket, 36.5 Mtr. length x 20 mm dia high pressure hose reel tubing as per IS: 444 with gun metal (GM) shut off nozzle having 5 mm dia orifice. The hose reel shall be conforming to IS : 884-1985. Rate shall include 25 mm dia M.S. pipe connection from Riser to hose reel, sockets, nipples, elbows and ball valve (25 mm dia). Drum shall be fixed on adjoining wall through anchor fasteners / cement concrete block as and when required complete in all respects and to the best satisfaction of Engineer-in-charge.. |
| 30 | Make: Minimax/OMEX/ Padmini |
| 31 | Weather proof standard fire hose cabinet made of 18 SWG powder coated fibre. sheet having single or double opening glazed (3.0 mm thick glass) shutter including necessary locking arrangement by allan key, stove enamelled Fire red finish (as per IS : 5, shade no. 536) with \\" Fire Hose\\" marked on front, suitable for housing 2 nos. 15m long 63 mm dia Hose pipe, 1 No. branch pipe & nozzle spanner as required complete in all respects and to the best satisfaction of Engineer-in-charge. |
| 32 | Make: Minimax/OMEX/ Padmini |
| 33 | Providing Cast iron /steel Butterfly Valve Confirming to type P.N 1.6 of I.S 13095-1991 Complete with Flanges bolt, nuts, gasket etc. As per table 'E' specification complete in all respect hydraulically test to 20 K./sqcm. as required complete in all respects and to the best satisfaction of Engineer-in-charge. |
| 34 | 80 mm Dia |
| 35 | 100 mm Dia |
| 36 | 150 mm Dia |
| 37 | 200 mm Dia |
| 38 | Makes:-Zoloto/Sant/Audco |
| 39 | Providing and fixing Cast Iron dual plated Check Valve (NRV) horizontal type with gunmetal seat non-return valve confirming to class - I of IS : 5312 including nuts, bolts, 1.5 mm thick compressed asbestos gasket as per table \\"E\\" and specifications as required complete in all respects and to the best satisfaction of Engineer-in-charge. |
| 40 | 80 mm dia |
| 41 | 100 mm Dia |
| 42 | 150 mm Dia |
| 43 | Makes:-Zoloto/Sant/Audco |
| 44 | Providing & fixing Gunmetal Collecting head inlet connection to external hydrant ring/hydrant riser with 4 Nos. 63 mm dia instantaneous type inlet and 150 mm dia flanges outlet conforming to IS:904 with blank cap and chain. |
| 45 | Make: Minimax/OMEX/ Padmini |
| 46 | Supply, installation, testing and commissioning of electrically driven high pressure centrifugal fire hydrant / sprinkler pump, suitable for automatic operation consisting of the following: |
| 47 | (a).Multistage Multi-outlet, centrifugal pump (Flow : 2280 LPM and Head : 70 mtr), suitable for operation on 415 volts ± 10 %, 3 phase, 50 HZ A.C supply. The installation shall be complete with flexible coupling and coupling guard as required. Fire pump shall have C.I. casing, CS diffusers, bronze impeller (hard finished and dynamically balanced) and S.S. (410) Shaft with mechanical seal, capable for delivering the required flow at the required head to ensure a minimum pressure of 3.5 Kg/Sqcm at the farthest or topmost hydrant / sprinkler. The installation shall be complete with necessary pressure gauge with gun metal shut off cock on delivery side.(b).Squirrel cage induction motor, TEFC type suitable for operation on 415 volts, 3 phase 50 HZ A.C supply, of suitable Capacity (45 KW.) for the above pump with synchronous speed of 2900 RPM, conforming to IP 55 protection & class F insulation. The motor shall conform to IS 325-1978 (up to date) with flexible coupling and coupling guard, complete as required.Common base plate for (a) and (b) from G.I.Channel for required size.(d)d) Suitable RCC pump-Foundations as per manufactures design and 4 nos Dunlop (cushy foot) heavy duty Antivibration mounting pads. |
| 48 | Make:- Kirloskar/Siemens/Grundfoss |
| 49 | Supply, installation, testing and commissioning of Diesel Engine driven fire pump suitable for automatic operation comprising of the following and conforming to BS 649/IS 10002 all amended upto date. |
| 50 | A) Horizontally mounting,centrifugal type single/multi-stage fire pump having cast ironbody, bronze impeller,stainless steel shaft &capable of delivering 2280LPM against a total head of 70 M complete withnecrssary Y stainer on the sunction side and pressure gauge with stop cocks etc. on the delivery side including bybass arrangement (with 50mm dia GM stop valve and upto 5mGI stop valve and upto 5M GI medium pipe) for perodical testing of thepumping set of the pumping set as per TAC rules. b) Water cooled TAC approved Diesel Engine suitable for the developing at least 62 BHP at 2150RPM for above pumping complete with autmatic starting mechanism, batteries,automatic battery charger unit,flexble coupling withthe pump,coupling with the pump,fuel tank,silencer,exhaust pipe with insulation appro. 25m length& all standard accessories as requrid asper TAC rules including earthing,mandatory spares and tool kit. c) Common bed plate for mounting pump and Engine fabricated of suitable MS channel as per manufacturer recommendations. d)Suitable RCC pump foundation as per manufacture design 8Nos Dunlop Anti-vibration(cushy foot) heavy duty mounting pad. |
| 51 | Make:- Kirloskar/Siemens/Grundfoss |
| 52 | Supply, installation, testing and commissioning of jockey pump (pressurisation pump) comprising of the following: |
| 53 | (a)Horizontal pump(Flow :180 LPM and Head :70mtr) suitable for operation on 415 volts ± 6%, 3 phase, 50 HZ A.C supply. The installation shall be complete with Flexible coupling and coupling guard, complete as required.The pump casing shall be CI, shaft shall be SS & impeller/ shaft sleeve/casing wearing ring shall be bronze. The pump shall be provided with mechanical seal The system shall be complete with necessary pressure gauge with gun metal shut off cock on delivery side. b)Squirrel cage induction motor totally enclosed fan cooled type suitable for 415 volts +10%-10% 3 phase 50HZ AC supply of suitable capacity(appro11KW) for the above pump with synchronous speed of 1500/3000 RPM confirming to IS325 &duly coupled with above pump coupled with flexible coupling including earthing as per relevant Indian Standard and specification. c) Common bed plate for mounting pump and Motor fabricated of suitable MS channel as per manufactures recommendation. d)Suitable RCC pump foundation as per manufactures design Dunlop 4 Nos Dunlop Anti-vibration (cushy foot) heavy duty mounting pads. |
| 54 | Make:- Kirloskar/Siemens/Grundfoss |
| 55 | SITC of electrical main conrol panel made 16 gauge sheet with power coating consisting of following items.1No. Voltmeter with selector switch 3Nos Ampere meter with selector switch 3Nos.sets ofcurrent transformer MCCB 250 Amp-1No MCCB 200 Amp 1No Automatic starter,60 HP motor battery charging set Engine start-stop Relay Engine control AMF relay Engine crank relay Audio Hooter DC control relay Engine control selector switch 63 Amp MCCB-starter 15 HP motor 3 set of the start stop switch 9Nos.indicating lamps Automanul switchset, interlocking kit/terminal charging rate selector switch of trickle/boost. |
| 56 | Makes:- Advance/Delight Power Control or equivalent. |
| 57 | Supply, installation, testing and commissioning of Pressure switch for fire pumps of approved make,including necessary wiring and cut off valve up to central panel & other material as described in specifications. |
| 58 | Make:- Indfoss /System Sensor |
| 59 | Providing, installation,testing and commissioning of Stainless steel Y strainer fabricated out of 1.6 mm thick stainless steel. Grade 304 sheet with 3mm dia hole with stainless steel flange including carriage of material in all leads and lift. |
| 60 | 200 mm dia. |
| 61 | Suppling and installation following Size of Perforated Hot Dipped Galvanised iron cable tray (Galvanisation thickness not less than 50 microns) with perforation not more than 17.5% in convenient sections, joined with connectors, suspended from the celling with G.I suspenders including G.I bolts & nuts,etc as required. |
| 62 | 225 mm width X 50 mm depth X 1.6 m Thickness |
| 63 | Providing and laying of one No. aluminium conductor, PVC insulated and PVC sheathed, armoured/XLPE power cable, working voltage 1100 volts grade direct in ground; to be laid 1 meter below the ground level including excavation and refilling the trench etc.as required, but excluding sand cushioning and protective covering:- |
| 64 | Armoured cable 35 sq. mm ( Four core) |
| 65 | Armoured cable 70 sq. mm ( Four core) Please Enable Macros to View BoQ information |
AI Tender Summary
Tender Timeline
Jul 10, 2026
11:30 IST
Tender Published
Tender notice published.
CompletedJul 17, 2026
17:00 IST
Bid Submission Deadline
Online submission via eProcurement portal.
Upcoming · 5 daysJul 17, 2026
Bid Opening Date
Technical bids will be opened and evaluated.
Upcoming · 5 daysTender Documents
Download All (ZIP) ↓
Disclaimer
We takes all possible care for accurate & authentic tender information. However users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender