Tender For Certain Repair To Roof Covering, Joinery, False Ceiling, Glazing And Allied Works At Rakhmuthi Mil Stn And Its Outstations Under Ge (S) Akhnoor.
Tender Value
40 Lakhs
Estimated cost
Bid Submission
31 Jul 2026
18 days left
EMD
80000
Bank guarantee accepted
Document Fee
500
Non-refundable
Tender Type
Online
Tender Overview
Organization
Tender ID
Competition Type
NCB
Bidding Type
Tender
Location / State
Jammu → Jammu and Kashmir
EMD Exemption
Not Available
Quantity
Not Available
Website
Contact Person
Address
Project Description
Tender for Certain Repair To Roof Covering, Joinery, False Ceiling, Glazing And Allied Works At Rakhmuthi Mil Stn And Its Outstations Under Ge (S) Akhnoor.
BOQ
| Sl. No. | Item Description |
| 1 | Dismantling of mild steel work of any description, complete all specified and directed. |
| 2 | Dismantling timber scantlings 40 Sqcm and over in section, in any position, unframed work, complete all as specified and as directed by Engineer-In-Charge. |
| 3 | S&F for mild steel rolled sections as in main and cross beams, hip and jack rafters; purlins where connected to common rafters and running rails and guides for sliding doors; fixed with angle cleats or other connecting plates, confirming to grade Fe 410-W (Gde E-250 quality-A), complete all as specified and directed. |
| 4 | Fixing only mild steel rolled sections as in main and cross beams, hip and jack rafters; purlins where connected to common rafters and running rails and guides for sliding doors; fixed with angle cleats or other connecting plates, confirming to grade Fe 410-W (Gde E-250 quality-A), complete all as specified and directed. |
| 5 | Dismantling asbestos cement (corrugated, semicorrugated, etc.) sheets in roof coverings, complete all as specified and as directed by Engineer-In-Charge. |
| 6 | Dismantling of plain or corrugated steel sheeting, any gauge, thickness, including any pattern roof coverings, complete all as specified and directed by Engineer-In-Charge. |
| 7 | S&F for galvanised, corrugated mild steel sheeting, 0.63mm thick, with two corrugations side lap, fixed with L-type or J-type or cranked hook bolts sand washers, in roofs, walls etc. with grade of zinc coating 275, complete all as specified and as directed by Engineer-In-Charge. |
| 8 | S&F for plain, galvanised, mild steel sheeting, 0.80mm thick, in ridges, hips, valley gutters, drip and straight flashings (length and girth as fixed) with grade of zinc coating 275, fixed with L-type or J-type or cranked hook bolts sand washers, in roofs, walls etc. with grade of zinc coating 275, complete all as specified and as directed by Engineer-In-Charge. |
| 9 | S&F for pre- painted galvalume aluminum zinc coating GI based corrugated steel sheet 0.50mm thick of an colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws as specified & directed, complete all specified and directed. |
| 10 | Fixing only pre- painted galvalume aluminum zinc coating GI based corrugated steel sheet 0.50mm thick of an colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws as specified & directed, complete all specified and directed. |
| 11 | S&F for pre-painted galvalume aluminum zinc coating GI based plain steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/ cladding to wall, fixed with self tapping screws, complete all specified and directed. |
| 12 | Dismantling of wall and ceiling boards (fibre, pulp, insulation, etc.) or insulation boards/ slabs/ blankets, any thickness, including cover fillets, complete all as specified and as directed by Engineer-In-Charge. |
| 13 | S&F for Non asbestos ceiling board of 4mm thick, designer, in ceiling fixed as per manufacturer’s instructions, including powder coated galvanised iron snap grid frame work of main and tee (weight not less than 240gm/Rm), angle (weight not less than 217 gm/Rm), grid size 595x595mm, for false ceiling all as specified, and hangers not less than 6mm nominal dia, galvanised iron (upto 1200mm length) adjusting level fixed to roof slabs by means of ceilling cleats made out of galvanised iron wire of 4.0mm dia, length as required at site and expansion hold fasteners 12.50mm dia, 40mm long, complete all specified and directed. |
| 14 | FIxing only ceiling board of 4mm thick, designer, in ceiling fixed as per manufacturer’s instructions, including powder coated galvanised iron snap grid frame work of main and tee (weight not less than 240gm/Rm), angle (weight not less than 217 gm/Rm), grid size 595x595mm, for false ceiling all as specified, and hangers not less than 6mm nominal dia, galvanised iron (upto 1200mm length) adjusting level fixed to roof slabs by means of ceilling cleats made out of galvanised iron wire of 4.0mm dia, length as required at site and expansion hold fasteners 12.50mm dia, 40mm long,complete all as specified and as directed. |
| 15 | Demolition of brickwork or stone/ boulder masonry, built in cement mortar including all quoins, arches, pillars, etc, but excluding ashlar facings, dressed stonework and precast concrete articles, complete all as specified and as directed. |
| 16 | M&L for brick work with sub class 'B' bricks old size straight or curved in plane exc 6m mean radius built in cement mortar 1:6, complete all as specified and directed. |
| 17 | Descriptionn all as per serial item No. 15 but except brick, complete all as specified and as directed by Engineer-in-Charge. |
| 18 | Taking down cement plaster on brick or stone walls etc including raking out joints, hacking for key, scrubbing down with water etc, complete all as specified and directed. |
| 19 | M&L for rendering 10 mm thick in cement mortar 1:6 on any surfaces of brick work or concrete surfaces, finished even & smooth without using extra cement, complete all specified and directed. |
| 20 | M&L for rendering 15 mm thick in cement mortar 1:4 on fair faces of brick work or concrete surfaces, finished even & smooth without using extra cement,complete all specified and directed. |
| 21 | M&L for preparation of new plastered or unplastered surfaces of walls and applying two coats of oil bound distemper over a promer coat of chalk whitening , complete all as specified and as directed. |
| 22 | M&L for preparation of new plastered or unplastered surfaces of walls and applying two coats of cement based paint over a coat of primer , complete all as specified and as directed. |
| 23 | M&L for preparation of old/ decorated plastered or unplastered surfaces of walls and applying one coat of cement paint, complete all as specified and as directed by Engineer-In-Charge. |
| 24 | M&L for preparation of old/ decorated plastered or unplastered surfaces of walls and applying one coat of oil bound distemper (different colour), complete all as specified and as directed by Engineer-In-Charge. |
| 25 | Taking down chowkats or frames with shutters (without taking off shutters from the frames) not exceeding 1.5 Sqm each, complete all as specified and directed by Engineer-In-Charge. |
| 26 | Taking down chowkhat or frame with shutters (without taking off shutters from frames) exc. 1.5 Sqm but n.exc 4 Sqm each, complete all as specified and directed by Engineer-In-Charge. |
| 27 | Taking down shutter of any description exceeding 1.0 Sqm but not exceeding 2.0 Sqm, complete all as specified and directed. |
| 28 | S&F for aluminium powder coated (minimum thickness of powder coating 50micron) frame for window, ventilator with one or more rebates including joining cleat for fixing etc, complete all as specified and as directed. |
| 29 | S&F for powder coated aluminium door shutters, aluminium section weighing 0.55 kg/m including necessary joining cleats,glazing clips, ruber neoprene packing, handles 2 Nos in each door, hinges,door seal at bottom,anodised aluminum snap beading screws etc.(thickness of powder coating should not less than 50 micron) including 5.5 mm Sheet glass,ordinary quality fixed in windows in square exc 0.5 sqm and 2 mm aluminium sheet and bottom panel, complete all as specified and as directed complete all as specified and as directed. |
| 30 | S&F for aluminium powder coated window ( including glazed and skelton shutter ) and ventilator shutters, side hung type without sash bars, aluminium sections weighing 0.55 kg/m including glass of 5.5 mm thick, necessary joining cleats, glazing clips,rubber packing, anodised aluminium snap beading, screws, anodised aluminium fittings such as peg stays 150mm long (1 no.). hinges type B-21 100mm long (2 no.)suitable handle (1 no.) (thickness of powder coating should not less than 50 micron) complete all as specified and as directed by Engineer-in-Charge. |
| 31 | S&F for aluminium powder coated window, side hung type without sash bars, aluminium sections weighing 0.55 kg/m including Galvanised mild steel wire cloth, 0.46 mm nominal dia of wire and average width of aperture 1.18mm , including anodised aluminium grill of mesh size 70mm x70 mm and thickness 3-4 mm (anodised transparent or dyed to required shade according to IS: 1868 with minimum anodic coating of grade AC 15) of approved design/pattern, with approved standard section and fixed to window shutter frame with C.P. brass/ stainless steel screws @ 200 mm centre to centre, including cutting the grill to proper opening size for fixing and operation of handles and fixing approved anodised aluminium standard section around the openingnecessary joining cleats, glazing clips,rubber packing, anodised aluminium snap beading, screws, anodised aluminium fittings such as peg stays 150mm long (1 no.). hinges type B-21 100mm long (2 no.)suitable handle (1 no.) (thickness of powder coating should not less than 50 micron) complete all as specified and as directed by Engineer-in-Charge. |
| 32 | S&F in repair for aluminium (extruded section) body door closer hydraulically regulated, designation No. 3, universal type, suitable for door shutters of 851 to 1000 mm in width and of weight between 61 to 80 kg ISI marked, complete all as specified and as directed. Please Enable Macros to View BoQ information |
| 33 | S&F in repair for aluminium (extruded section) body door closer hydraulically regulated, designation No. 3, universal type, suitable for door shutters of 851 to 1000 mm in width and of weight between 61 to 80 kg ISI marked, complete all as specified and as directed. Please Enable Macros to View BoQ information |
AI Tender Summary
Tender Timeline
Jul 10, 2026
11:30 IST
Tender Published
Tender notice published.
CompletedJul 31, 2026
17:00 IST
Bid Submission Deadline
Online submission via eProcurement portal.
Upcoming · 18 daysAug 07, 2026
Bid Opening Date
Technical bids will be opened and evaluated.
Upcoming · 25 daysTender Documents
Download All (ZIP) ↓
Disclaimer
We takes all possible care for accurate & authentic tender information. However users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender