Tender For Certain Repairs To Joinery, Ceiling, Aluminium Partition And Other Allied Works In Zone-I, Etf, Aag And Domestic Area At Tbrl Range Ramgarh
Tender Value
20 Lakhs
Estimated cost
Bid Submission
30 Jul 2026
17 days left
EMD
40000
Bank guarantee accepted
Document Fee
500
Non-refundable
Tender Type
Online
Tender Overview
Organization
Tender ID
Competition Type
NCB
Bidding Type
Tender
Location / State
Panchkula → Haryana
EMD Exemption
Available
Quantity
Not Available
Website
Contact Person
Address
Project Description
Tender for Certain Repairs To Joinery, Ceiling, Aluminium Partition And Other Allied Works In Zone-I, Etf, Aag And Domestic Area At Tbrl Range Ramgarh
BOQ
| Sl. No. | Item Description |
| 1 | Taking down chowkhats or frames with shutters (without taking off shutters from the frame) n.exc. 1.5 Sqm each complete all as specified and directed. |
| 2 | All as per serial item No 1 above but exc. 1.5 Sqm and n.exc. 4 Sqm each complete all as specified and directed. |
| 3 | Taking down shutters of any description n.exc. 1 Sqm each complete all as specified and directed. |
| 4 | All as per serial item No 3 above but exc. 1 Sqm and n.exc. 2 Sqm each complete all as specified and directed.. |
| 5 | Refixing shutters in same opening of any description n exc 1 Sqm each in same opening complete all as specified and directed. |
| 6 | Refixing shutters in same opening of any description exc 1 Sqm but n exc 2 sqm each in same opening complete all as specified and directed. |
| 7 | Cutting holes for inserting hold fast and making good dismantled portion in CM (1:3) in brick walls, built in cement mortar or cement concrete 1:2:4 type B1as required exc one brick but not exc two bricks complete all as specified and direcrted. |
| 8 | Supply and fixing for factory made solid panel PVC door shutter 30mm thick (style) consisting of frame made out of M.S tubes for top & bottom rails. M.S frame shall be covered with heat moulded plain colour PVC C channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheet for top rail, lock rail & bottom rail, on either side & as gap insert for top rail & bottom rail. Panelling of plain colour PVC sheet to be fitted in the M.S frame welded/sealed to the stiles & rails with suitable PVC sheet beading and jointed together with solvent cement complete all as specified and directed. |
| 9 | Supply and fixing for factory made solid PVC chowkhats or frames of size 50mmX47mm made out of 5mm plain colour PVC sheet reinforced with MS Square tube, complete all as specified and directed. |
| 10 | Supply and fixing for aluminium anodized barrel tower bolt of extruded section 150mm long complete all as specified and directed. |
| 11 | All as per serial iten no 10 but 100mm long complete all as specified and directed. |
| 12 | Supply and fixing aluminium anodized handle of extruded section 150mm long complete all as specified and directed. |
| 13 | All as per serial item no 12 above but 125mm long complete all as specified and directed. |
| 14 | Supply and fixing for aluminium anodized floor door stopper 140mm long overall length ccomplete all as specified and directed. |
| 15 | Supply and fixing for stainless steel butt hinges medium weight cold rolled 100mm size ccomplete all as specified and directed. |
| 16 | All as per serial item no 15 above but 75mm size complete all as specified and directed.. |
| 17 | Supply and fixing for continuous (piano) hinges, mild steel, bright finish or electro-galvanised width of trap when open 40mm thick complete all as specified and directed. |
| 18 | Supply and fixing for 40mm dia, cupboard knobs fixed with nut, screw and washer of mild steel bright finished complete all as specified and directed. |
| 19 | Supply and fixing for 100mm size of aluminium hasp & staple including bolt to hinge plate & fixed with screws complete all as specified and directed. |
| 20 | Supply and fixing for steel windows with side hung shutters including projecting type hinges with steel handles,steel peg stays complete with glazing bars dovetailed or welded complete all as specified and directed. |
| 21 | Supply and fixing for steel ventilator with top hung shutter includig hinges steel peg stay, handle complete all as specified and directed. |
| 22 | Material and labour for framed work such as grills, gratings, etc. with ends of bars shouldered and/or riveted, or forged into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; framework of water tanks and similar work conforming to Fe.290.Gde-E-165 complete all as specified and directed. |
| 23 | Material and labour for plain, solid, straight chowkhats and frames, wrought framed rebated on the solid, rounded or chamfered, put together with glue, pinned at joints using 2nd class hardwood (hollock) complete all as specified and directed. |
| 24 | Supply and fixing for 105X60mm pressed steel frames for doors with one or more rebates including necessary fixing lugs hinges lock strike plate etc complete all as specified and directed. |
| 25 | Supply and fixing for 125X60mm pressed steel frames for doors with one or more rebates including necessary fixing lugs, hinges, lock strike plate etc complete all as specified and as directed. |
| 26 | Material and labour for 30mm thick 2nd class hardwood (Hollock) factory Plain, framed, panelled shutters (any number of panels), with panels of timber flat on both sides (feather edged), or of veneered particle board medium density, wood particle board with commercial face veneers: supplied chowkats complete all as specified and directed. |
| 27 | Supply and fixing for 35mm thick 2nd class hardwood (Hollock) factory made glazed and skelton shutters, open rebated and prepared to receive glass etc divided into squares with sash bars, edges of framing plain, chamfered or rounded fitted with cut and mitered beads for securing glass etc, size of members complete all as specified and directed. |
| 28 | Supply and fixing for 18mm thick both side prelaminated high density high moisture resistances (HDHMR) board any colour / sunmica finished wood grains, with white base paint finish UV HDHMR corner side rounding with edge bending tape, PVC boxes, drawer any shape and sizes will be made up by machines matching with final finish (UV) complete all as specified and directed. Note :- Design and colour approved by Engr-in-Charge) |
| 29 | Supply and fixing for 2nd class hard wood plain fillets sectional area exc. 6sqcm n.exc. 13 Sqcm clean sawn, secured with nails or brads complete all as specified and directed. |
| 30 | Supply and fixing for 2nd class hard wood plain fillets sectional area exc. 3sqcm n.exc. 6 Sqcm clean sawn, secured with nails or brads complete all as specified and directed. |
| 31 | Supply and fixing for MS helical door spring (rat tail pattern) 300mm long including roller and roller plate complete including welding and providing 40x3 mm size 75 cm long flat iron welded to angle iron frame as in repair complete all as specified and directed. |
| 32 | Supply and fixing for galvanized mild steel wire cloth 0.56mm nominal dia of wire and average width of aperture 1.18mm and fixed with tinned tacks or galvanized wire staples complete all as specified and directed. |
| 33 | All as per serial item No 32 above but fixed in repairs complete all as specified and directed. |
| 34 | Dismantling structural steel work incl doors, gates but excluding framed, trusses etc complete all as specified and directed.. |
| 35 | Supply and fixing for mild steel work as in doors or gates of angle or other section of grade Fe-410 W(Gde E-250) quality B with gusset plates, rails, braces etc complete drilled for fixing of steel sheeting or other covering doors etc to be prepared for hanging or sliding with and including either hooks and hinges or steel hanging door fitting (exclusive of steel sheeting) fasteing and fixing complete fixed in repair complete all as specified and directed. |
| 36 | Material and labour for PCC 1:3:6 type C-0 using 12.5mm graded stone aggregate as in filling of pressed steel chowkats complete all as specified and directed. |
| 37 | Supply and fixing for 30mm thick flush shutters, solid core construction, with block board core and both face covered with decorative face veneer with lipping/ frame to match complete all as specified and directed. |
| 38 | Hacking out old broken glass (any thickness, size, quality or description) from wooden/steel frame complete all as specified and directed. |
| 39 | Supply and fixing for 4.80mm thick sheet glass, ordinary quality and glazing with oil putty in square n exc 0.5 sq. m in each pane complete all as specified and directed. |
| 40 | Supply and fixing for 5.50mm thick Sheet glass, ordinary quality and glazing with oil putty in square exc 0.5 sq. m in each pane complete all as specified and directed.. |
| 41 | Supply and fixing for rough cast, wired figured glass, 6.4mm thick and glazing with oil putty in square n exc 0.5 sqm in each pane complete all as specified and directed. |
| 42 | All as per serial item no 41 above but exc 0.5 sqm but n exc 0.75 sqm in each pane complete all as specified and directed. |
| 43 | All as per serial item no 41 above but exc 0.75 sqm but n exc 1.00 sqm in each pane complete all as specified and directed.. |
| 44 | Supply and fixing for figured glass, pin head type and glazing with oil putty in squares n.exc. 0.5 Sqm each of thickness 3.0mm complete all as specified and directed.. |
| 45 | Supply and fixing in repair 12mm thick toughened glass as in hinged doors, partitions automatic doors and similar work including cutting to shape, drilling holes as required complete all as specified and directed.. |
| 46 | Providing and fixing in repair Powder coated aluminium (minimum thickness of powder coating 50 micron) work for doors, windows, ventilators and partitions (Fixed portions) with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS:1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, aluminium snap beading for glazing/ paneling, C.P. brass/ stainless steel screws, all complete as per architectural drawings and the directions complete all as specified and directed. |
| 47 | Supply and fixing for powder coated of any colour (minimum thickness of powder coating 50 micron) anodised aluminium door shutters, aluminium section weighing 0.55 kg/m including necessary joining cleats, glazing clips, ruber neoprene packing,handles 2 Nos in each door, 150mm long tower bolt 2 Nos, hinges anodised aluminum snap beading screws etc complete all as specified and directed. |
| 48 | Taking down aluminium door shutters of size exc. 1.00 Sqm but n.exc. 2.00 Sqm, dismantling the door, both sides screwed and tightening inside frame, both side bottled & reassembled the door, fittings all items glass beading, hinges replacing rubber/aluminium beading where defective and fitted in position complete all as specified and directed. |
| 49 | Supply and fixing for double action floor spring hydraulically regulated made up of minimum 1.25 mm thickaluminium alloy sheet foundation box, main body with stainless steel cover, governing pivot made of brass, other parts made of mild steel heavy duty and fixed fixed in repairs complete all as specified and directed. |
| 50 | Supply and fixing for aluminium (Die cast) body door closer hydraulic regulated, designation No. 2, universal type, suitable for door shutters of 701 to 850 mm in width and of weight between 36 to 60 kg complete all as specified and directed. |
| 51 | Supply and fixing in repair aluminium (Die cast) body door closer hydraulic regulated, designation No. 2, universal type, suitable for door shutters of 701 to 850 mm in width and of weight between 36 to 60 kg complete all as specified and directed. |
| 52 | Supply and fixing in repairs 100mm size mortice locks of brass body, 4 levers suitable to aluminium door shutters complete all as specified and directed. |
| 53 | Supply and fixing in repair powder coated aluminium window and ventilator shutters, side hung type without sash bars, aluminium sections weighing 0.55 kg/m including 5mm thick plain glass, necessary joining cleats, glazing clips, rubber packing, anodised aluminium snap beading, screws, anodised aluminium fittings such as peg stays 150mm long (1 no.). hinges type B-21 100mm long (2 no.) suitable handle (1 no.) complete all as specified and directed. |
| 54 | Supply and fixing in repair collapsible steel gates, top hung, consisting of channel pickets, pivoted flat bars top & bottom runners, MS handles, etc as specified, erected in position and securing runners with hold fasts & brackets complete all as specified and directed. |
| 55 | Supply and fixing in repairs venetian blinds, sheer demout zebra blinds of with aluminium roller tube, cassette colour white fabric weight 140gms, light control 70% fabric composition 100% polyester complete all as specified and directed |
| 56 | Supply and fixing in repairs venetian blinds, vertical type, complete all as specified and directed. Make - Vista or equivalent . |
| 57 | Supply and fixing in repairs powder coated aluminium grills, fixed to aluminium windows/partitions /door frame including all fixing arrangements like aluminium channels, screws etc complete all as specified and directed. |
| 58 | Dismantling existing wall/ceiling board, partition any type including wooden framed work/GI frame work of any size & specifications complete all as specified and directed. |
| 59 | Material and labour for suspended false ceilling comprising of 4mm thick non asbestos fibre cement bulding boards fixed or laid/inserted to GI frame work with screws over Gl frame work for seamless ceiling comprising of Gl perimeter channnel 0.55 mm thick with two unequal flanges of 20 and 30 mm and web of 27 mm fixed to surrounding wall using nylon sleeves and screws at 450 mm centre to centre/ intermediate channel 0.9 mm thick having two equal flanges of 15 mm each and web of 45 mm suspended from soffit at approx 900 mm centre to centre with Gl cleat and steel expansion fasteners with and including ceiling section (not exc 1.2 m length) of 0.55 mm thickness having kurled web of 50 mm and flange of 26 mm each with lips of 10.5 mm fixed to the intermediate channel with connecting clips across the intermediate channel at 457 mm centre to centre. Hangers 6 mm dia. G.I. (upto 1200mm length) adjusting level fixed to roof slabs by means of ceilling cleats made out of G.I. flat 40 x 3 mm size 60mm long and expansion hold fasteners 12.5mm dia. 40mm long complete all as specified and directed. |
| 60 | Supply and fixing for 12mm thick gypsum board including two coat of oil bound distemper with Gl frame work for seamless ceiling comprising of Gl perimeter channnel 0.55 mm thick with two unequal flanges of 20 and 30 mm and web of 27 mm fixed to surrounding wall using nylon sleeves and screws at 450 mm centre to centre/intermediate channel 0.9 mm thick having two equal flanges of 15 mm each and web of 45 mm suspended from soffit at approx 900 mm centre to centre with Gl cleat and steel expansion fasteners with and including ceiling section (not exc 1.2 m length) of 0.55 mm thickness having kurled web of 50 mm and flange of 26 mm each with lips of 10.5 mm fixed to the intermediate channel with connecting clips across the intermediate channel at 457 mm centre to centre complete all as specified and directed. |
| 61 | Supply and fixing for solid PVC wall lining/panelling consisting of 4 to 5mm thick hollow type, single side prelam PVC sheet used instead of plain colour sheet fix to wall with screws incl matching PVC beading complete all as specified and directed. |
| 62 | Supply and fixing for 5mm thick PVC sheet fillet of width 35mm for wall paneling inclusive of fixing on to wall to make PVC frame as per specification and drawing complete all as specified and directed.. |
| 63 | Material and labour in repairs 12 mm thick particle board, medium density, flat pressed, single layer type or three layer type with BWR type adhesive, fixed with screws to timber frame work complete all as specified and directed. |
| 64 | Supply and fixing for 300mm Aluminium alloy, anodised, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast-aluminium alloy and fixed complete all as specified and directed. |
| 65 | Supply and fixing for rubber beading in aluminium doors and windows fixed in repair complete all as specified and directed. |
| 66 | Supply and fixing for aluminium beading in aluminium doors and windows fixed with screw as in repair complete all as specified and directed. |
| 67 | Supply and fixing in repairs gauge springs for rolling shutters as per existing complete all as specified and directed. |
| 68 | Supply and fixing in repair 5mm thick polycarbonate multi wall sheet both side UV Coated, fixed with coach/Self taping screws and fixed on MS/Aluminium framed work complete all as specified and directed. |
| 69 | Material and labour for PCC 1:2:4 type B-1, using 20mm graded crushed stone aggregate as in bed plates, hold fast, lacing course coping, bed blocks etc complete all as specified and directed. |
| 70 | Demolition of brick / block masonry built in CM including all quoins, arches, pillars etc and clearing rubbish off the premises complete all as specified and directed.. |
| 71 | Material and labour for brick work with subclass B bricks, straight or curved on plan exc 6m mean radius built in cement mortar (1:6) complete all as speecified and directed |
| 72 | All as per serial item No. 71 above but except brick complete all as specified and directed. |
| 73 | Taking down cement plaster on brick walls including hacking out joints, hacking for key, scrubbing down with water complete all as specified and directed.. |
| 74 | Material and labour for rendering 15 mm thick on internal surface using cement plaster in CM 1:6 on fair faces of brick/concrete work surfaces complete all as specified and directed. |
| 75 | Material and labour Rendering 15 mm thick on external surface using cement plaster in CM 1:4 on fair faces of brick/concrete work surfaces complete all as specified and directed.. |
| 76 | Material and labour for two coats of synthetic enamel painting over a coat of pink primer including preparation of surfaces of wood or wood based material exc. 10 cm width or girth complete all as specified and directed. |
| 77 | Material and labour for two coats of synthetic enamel paint including one coat of red oxide primer on steel surfaces exc. 10cm width or girth including preparation of new surfaces, complete all as specified and directed. |
| 78 | Material and labour for two coats of cement base paint over a coat of primer on new plastered surfaces including preparation of surfaces complete all as specified and directed. |
| 79 | Material and labour for preparing newly plastered surfaces and applying two coats of oil bound distemper over a coat of 1mm thick wall care putty on walls complete all as specified and directed. Please Enable Macros to View BoQ information |
AI Tender Summary
Tender Timeline
Jul 09, 2026
11:30 IST
Tender Published
Tender notice published.
CompletedJul 30, 2026
17:00 IST
Bid Submission Deadline
Online submission via eProcurement portal.
Upcoming · 17 daysAug 03, 2026
Bid Opening Date
Technical bids will be opened and evaluated.
Upcoming · 21 daysTender Documents
Download All (ZIP) ↓
Disclaimer
We takes all possible care for accurate & authentic tender information. However users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender