Tender For special Repair To Bldg No A/8/116 (Single Living Or Line) & A/8/494 (Toilet Block) At Pms Under Ge Panagarh
Tender Value
37.93 Lakhs
Estimated cost
Bid Submission
30 Jul 2026
19 days left
EMD
75900
Bank guarantee accepted
Document Fee
500
Non-refundable
Tender Type
Online
Tender Overview
Organization
Tender ID
Competition Type
NCB
Bidding Type
Tender
Location / State
Purba Bardhaman → West Bengal
EMD Exemption
Not Available
Quantity
Not Available
Website
Contact Person
Address
Project Description
Tender for special Repair To Bldg No A/8/116 (Single Living Or Line) & A/8/494 (Toilet Block) At Pms Under Ge Panagarh
BOQ
| Sl. No. | Item Description |
| 1 | Demolition of Brickwork or stone/ boulder masonry, built in cement mortar or cement lime mortar including all quoins, arches, pillars, etc, but excluding ashlar facings, dressed stonework and precast concrete articles complete all as sepcified and directed. |
| 2 | M&L for fly ash brick work, old size straight or curved on plan exc 6 mtr mean radius built in CM 1:6 complete all as specified and directed. |
| 3 | Demolition of cement concrete reinforced as in chajja & similar suspended work (other than ground floor) complete all as specified and directed. |
| 4 | M & L for cement concrete 75mm thick 1:4:8, Type D-2 (Using 40 mm graded crushed stone aggregates) as in sub base for flooring etc complete all as specified and directed. |
| 5 | M&L for M-25 Design mix using 20mm graded crushed stone aggregate as in Foundations, including rafts, footings, foundation beams; plinth beams; bases for columns, etc.; basement slabs, under-reamed piles and mass concret complete all as specified and directed. |
| 6 | M&L for M-25 Design mix using 20mm graded crushed stone aggregate as in chajjas complete all as specified and directed. |
| 7 | M&L for M-25 Design mix using 20mm graded crushed stone aggregate as in Beams, cantilevers, bressummers, lintels over 1.5m span complete all as specified and directed. |
| 8 | M&L for Steel Centering and shuttering including strutting, propping etc. and removal of form to sides of concrete foundations, footings, bases of columns, raft and raft beams, sides and soffits (if any) of foundation and plinth beams; and similar work; vertical or to batter |
| 9 | M&L for Steel Centering and shuttering including strutting, propping etc. and removal of form to chullah hoods, chajjas, troughs and similar items including edge for fair finished surface of concreted complete all as specified and directed. |
| 10 | M&L for Steel Centering and shuttering including strutting, propping etc. and removal of form to sides and soffits of floor or roof beams, beam haunchings, girders, bressummers, lintels, cantilevers, shelves including sup- ports, overhangs, etc. also splays between floors and beams, etc. for fair finished surface of concrete, complete all as specified and directed. |
| 11 | M&L for rendering 15 mm thick on other than fair faces of brick work or concrete surfaces, finished fair and even) on walls in cement mortar (1:6), complete all as specified. |
| 12 | M&L for Rendering 15 mm thick cement plaster in CM 1:4 on fair faces of brick/concrete surfaces finished fair and even, mixed wth water proofing compound admixture (if directed) as per manufacturer's instruction, complete all as specified and directed.Note :- WPC will measuered and paid separatly under relevant item of schedule. |
| 13 | Supply only liquird water proofing compound complete all as specified. |
| 14 | Material & Labour for preparation of new surfaces of plastered walls and applying Two coats of Distempering with 1st quality acrylic distemper (ready mixed) having VOC content less than 50 gms/litre, of approved manufacturer, of required shade and colour complete, as per manufacturer's specification. over and including a coat of primer and 1.0 mm thick white wall care putty (premium quality) over plastered surfaces of walls to prepare the surface even and smooth complete all as specified . . |
| 15 | M&L for preparation of new surface and apply Two or more coats of 100% Premium acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives @ 1.43 litre/ 10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/ 10 sqm over new surface complete all as specified and directed. |
| 16 | M&L Mild steel TMT bars 10 mm dia & over , cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified. |
| 17 | S&F TMT reinforcement bar, conforming to Fe-500, 6mm to 8mm dia cut to length , bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire ( annealed) not less than 0.9mm dia or securing with chips. |
| 18 | S&F TMT reinforcement bar, conforming to Fe-500, 5mm dia and upto and including 10mm dia in stirrups, spacers and binders, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends as binding with and including mild steel wire (Annealed) not less than 0.9mm dia or securing with clips all as specified. |
| 19 | Dismantling framed trusses span n exd 10 mtr complete all as specified and directed. |
| 20 | M&L for Roof trusses (framed), trussed, purlins, crane gantries, rails and fastenings and heavy bracket framing (Beam, tee, angle, channel or flat sections) including distance pieces, cleats etc. Fe-410-W(Gde- E-250) quality-B complete all as specified and directed. |
| 21 | M&L Hand rails, half round or other steel section or core for wooden hand-rail straight portion, drilled and countersunk for balusters running bars, for doors, balusters, nosing to steps including embeding in concrete and screwing etc. wind ties for roof including securing bolts; complete all as specified and directed. |
| 22 | M&L for preparing of new steel & iron surfaces of any description, not otherwise described, over 10cm width or girth and applying two coats of synthetic enameled paint over a coat of Red oxide zinc chrome primer zinc chrome complete all as specified and as directed. |
| 23 | Dismantling (corrugated,semi corrugated ) sheet in roof covering complete all as specified and directed. |
| 24 | M & L for pre-painted hot-dip aluminium-zinc alloy metallic coated of any profile steel sheet corresponding to IS 15965:2012 of durability class 3, atmospheric classification category 3, coating class AZ150, 0.50 mm thick, of an approved colour and having yield strength of 550 MPa as in roof covering fixed with self tapping screws as specified up to anyheight including all necessary scaffolding and safety measures complete all as specified and directed |
| 25 | M & L for pre-painted hot-dip aluminium-zinc alloy metallic coated plain steel sheet as per IS 15965:2012 of durability class 3, atmospheric classification category 3, coating class AZ150, 0.50 mm thick, of an approved colour and having yield strength of 550 MPa as in ridge/ valley/ gutter fixed with self tapping screws as specified any height Mtr height including all necessary scaffolding and safety measures complete all as specified and directed |
| 26 | Taking down window chowkhats or frame not exceeding 1.5 Sq. m each with shutter(s) (without taking off shutters from the frame), including removing to store, complete all as specified. |
| 27 | Taking down chowkhats or frame exceeding 1.5 Sq. m but not exceeding 4 Sq. m each with shutter(s) (without taking off shutters from the frame), including removing to store, complete all as specified. |
| 28 | M&L for Factory made single extruded WPC (Wood Polymer Composite) solid door/ window/ Ceosetory windows & other Frames/ Chowkhat of size 60x125 mm comprising of virgin PVC polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/ wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) fabricated with miter joints after applying PVC solvent cement and screwed with full body threaded star headed SS screws having minimum frame density of 750 kg/ cum, screw withdrawal strength of 2200 N (Face) & 1100 N (Edge), minimum compressive strength of 58 N/mm2 , modules of elasticity 900 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/ moisture proof and fire retardan and fixed in position with MS hold fast/lugs/SS dash fasteners of required dia and length complete as per direction of Engineer-in-Charge. (M.S. hold fast/ lugs or SS dash fasteners shall be paid for separately Note: For WPC solid door/window frames, minus 5mm tolerance in dimension i.e depth and width of profile shall be acceptable. Variation in profile dimensions on plus side shall be acceptable but no extra payment on this account shall be made |
| 29 | S&F Factory made single extruded WPC (Wood Polymer Composite) solid decorative panelled decorative flush door shutter one side plain on other side of 30mm size comprising of virgin polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) having minimum density of 650 kg/cum and screw withdrawal strength of 1800 N (Face) & 900 N (Edge), minimum compressive strength 50 N/mm2 , modulus of elasticity 850 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/moisture proof and fire retardant and fixing with stainless steel butt hinges of required size with necessary full body threaded star headed counter sunk S.S screws, all as per direction of Engineer-In-Charge. (Note: stainless steel butt hinges and necessary S S screws shall be paid separately) |
| 30 | S&F for 35mm thick factory made single extruded WPC (wood polymer composite) solid wire gauzed i.e. panel will be of wire gauze in lieu of panel. The comprising of virgin polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/rice husk/wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) having minimum frame density of 650 kg/cum, screw withdrawal strength of 1800N (face) and 900N (Edge), minimum compressive strength of 50 N/mm2, modulus of elasticity 850N/mm2 and resistance to spread of flame of class A category with property of being termite /borer proof, water/moisture proof and fire retardant and fixing with stainless steel butt hings of required size with necessary full body threaded star headed counter sunk S.S screws , all as per direction of Engineer-in -Charge. Note :- Stainless steel butt hinges and necessary SS Screws shall be paid separately) |
| 31 | S&F solid PVC door frame of size 50mmx47mm made out of 5mm plain colour PVC sheet reinforced with MS square tube, supplying and fixing in opening as per specification and drawing. |
| 32 | S&F Factory made solid panel PVC door shutter 30mm thick (style) consisting of frame made out of MS tubes for top and bottom rails. MS frame shall be covered with heat moulded plain colour PVC 'C' channel having a PVC sheet trip of 20mm with stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail and bottom rail; panelling of plain colour PVC sheet to be fitted in the MS frame welded/sealed to the stiles and rails with suitable PVC sheet beading and joined together with solvent cement, supplying and fixing in the frame at site as per specification and drawing. |
| 33 | S&F Powder coated aluminium (minimum thickness of powder coating 50 micron) work for doors, windows,ventilators and partitions (Fixed portions) with extruded built up standard tubular sections/appropriate Z sections and other sections of approved make conforming to IS: 733 and IS:1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at nctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing/ paneling, C.Pbrass/ stainless steel screws, all complete as per architectural drawings and the directions of Engineer-in-Chief |
| 34 | S&F Providing and fixing Powder coated aluminium (minimum thickness of powder coating 50 micron) for shutters of doors, windows & ventilators including providing and fixing hinges/ pivots and making provision for fixing of fittings wherever required including the cost of EPDM rubber/neoprene gasket required (Fittings shall be paid for separately) with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS:1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing/paneling, C.P. brass/ stainless steel screws all.complete as per architectural drawings and the directions of Engineer-in-Charge. |
| 35 | S&F 4mm thick figured sheet glass ordinary quality any size and in any type of frame and glazing with oil putty (or beading ) in square n.exc 0.5 Sqm in each panes complete all as specified. |
| 36 | S & F Galvanised mild steel wire cloth, 0.56 mm nominal dia of wire and average width of aperture 1.18mm and fixed with stainless steel wire staples, complete all as specified. |
| 37 | S&F butt hinges, extruded alluminium,with mild steel hinge pin,bright polished and fixed, type 125 mm size B21 complete all as specified and directed. |
| 38 | S&F 150 mm long aluminium alloy handles,fabricated type, anodised complete all as specified and directed |
| 39 | S&F aluminium anodised 150 mm barrel tower bolts of extruded section complete all as specified and directed |
| 40 | S&F Aluminium alloy, anodised, 300 mm long sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast-aluminium alloy and fixed complete all as specified and directed. |
| 41 | M&L 75 mm cement concrete type B1 (1:2:4) using 20mm graded aggregate as in receiving floor finished complete all as specified and directed. |
| 42 | M&L for Non Skid ceramic white tiles 7mm to 8mm thick, (square or rectangular) area of each tile exc 0.18 Sqm but n. exc 0.38 sqm in floors etc , over & including 15 mm thick cement mortar (1:6) screed etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match, including dismantling of floor hearth or wall tiling incl cement martar bedding complete all as specified. |
| 43 | Material and labour for glazed ceramic white tiles in vertical surfaces of size 450x350x7mm thick quality not less than group II, straight edge, as in skirting , dados, walls etc set and jointed in neat cement slurry and pointed in white cement with pigment to match the shade of tiles over and including 10mm thick rendering in cement mortar 1:4 incl dismantling floor hearth or wall tiling, complete all as specified and directed. |
| 44 | Dismantling of building board of any discription fixed in any position complete all as specified and directed. |
| 45 | S&F in for 4 mm thick non asbestos fibrecement designer building boards fixed or laid/ inserted with and including to timber/GI / Aluminium frame work with screw fixed in ceiling flat or sloping with and including hangers 4 mm dia GI (up to 1200 mm length) adjusting level fixed to roof slabs by means of ceiling cleats made out of GI flat 40x3 mm size 60 mm long including anodised aluminium snap grid 605 x 605 mm frame work complete all as specified. |
| 46 | M&L for 75 mm thick cement concrete M10 (Nominal Mix) with 40mm graded crushed aggregate finished even and fair laid to a slope of 1 in 12, laid in alternate bays, each bay not exceeding 3 m length with joint filled with bituminous mastic filling comprising a mixture of 1 part of heated Industrial bitumen 85/25 grade and two parts of heated sand as in plinth protection complete all as specified |
| 47 | S & F in repairs vitreous china wash down water closet (pedestal pattern), white including thermoplastic seats and covers of grade 2 type, flat with hinging device of bronze or brass with nickel chromium plating, fixing bolt, connector to flush pipe and making connections to flush pipe, connector to branch soil pipe and anti syphonage pipes etc. including sealing the joints and making leak proof using sealant complete all as specified and as directed by Engineer-in-Charge. |
| 48 | S & F in repairs vitreous china squatting pan, 'Orissa\\" pattern, size 580 mm X 440 mm white with ‘P’ or ‘S” trap, front or back inlet and integral foot rests, any pattern and including fixing , connector to flush pipe, lime concrete bedding and making connections to flush pipe, connector to branch pipe and anti syphonage pipes etc. including sealing the joints and making leak proof using sealant complete all as specified and as directed by Engineer-in-Charge. |
| 49 | S&F in repair vitreous China wash basin white, flat back,size 550X450 mm excluding taps, waste, chain and plug and porcelain stopper but including brackets including cutting for pinning in ends of brackets or erecting stand but exclusive of fixing of supply and waste pipe complete all as spd and as directed. |
| 50 | S&F Vitreous China Urinal, Half stall type, white (excluding flushing cistern, flush pipe and waste pipe) bowl type (back or corner wall type), complete including providing and fixing plugs, bedding urinal against wall in cement mortar 1:2, securing urinal to plugs with and including 60mm long brass screws, pointing around urinal back in cement; fixing automatic flushing cistern with brackets, flush pipe, grating and Union for discharge pipe complete all as specified. |
| 51 | S&F Urinal Spreader of PTMT any colour for fixing with 15 mm dia pipe complete all as specified |
| 52 | S&F in repair 10 litre capacity PVC low level flushing cistern with all accessories complete fixed with WC including syphone pipe, PVC flushing pipe of size complete (with brackets) complete all as sepcified and directed. |
| 53 | S&F in repair PVC connection 15mm size PTMT nuts of length 600mm complete all as specified. |
| 54 | S&F in repair Pillar taps 15mm bore cast copper alloy, with capstan heads, chromium plated, screwed down high pressure, with or without lettered 'Hot' or 'Cold' with long screwed shanks and fly-nuts, screwed for iron pipe and fixed complete all as specified and as directed. |
| 55 | S&F as in repair bib taps cast copper alloy 15mm bore with fancy chromium plated screwed down, screwed for iron pipe or for brass ferrule complete all as sepcified and directed. |
| 56 | S&F in repairs health faucet (ABS body) mild steel chromium plated suitable for 15 mm dia pipe with 1.25 mtr long flexible tube and ABS wall hook including making connections and fixed in positions complete in all respect as specified and as directed. |
| 57 | S&F in repair toilet paper holder with flat recessed type stainless steel arm fixed to walls with chromium plated berass screws complete all as specified. |
| 58 | S&F in repair waste coupling of PTMT (half or full threaded) 32mm bore dia of discharge pipe complete all as specified and as directed. |
| 59 | S&F in repair sheet glass shelf assembly consisting of 5.5mm thick sheet glass shelf 12cm wide with chromium plated bracket guard and railing 60cm long complete all as specified and as directed. |
| 60 | S&F as in grating square 150mm size of PTMT(minimum 100 gms) complete all as sepcified and directed. |
| 61 | S&F as in repair tubular towel rail brass chromium plated 20 mm dia `D' type 60 cm long between flanges complete all as spd and directed. |
| 62 | S&F as in repair chromium plated shower roses 125 mm long with or without swivel joints, any size, including fixing fixing to steel pipe or union complete all as specified and direceted. |
| 63 | S&F in repairs 15 mm bore angle valves, cast copper alloy screwed down high pressure with crutch or butterfly handle screwed both ends for iron pipe or for unions complete all as specified and as directed. |
| 64 | S&F in repair soap dish, any type fixed to plugs chromium plated brass screws complete all as specified and as directed. |
| 65 | Cutting chases in brick walls, pinning in, making good to facings where required and pointing in cement mortar 1:3 and cutting chases for concealed water tubing and making good of groves for concealed GI tube, cutting not exc 10cm girth complete all as specified and as directed. |
| 66 | S&F 20 mm outer dia medium grade CPVC, SDR 11 & plain CPVC SDR 11 with all fittings (brass inside the fittings) and fixed complete to walls and ceiling or laid in floors complete all as specified and directed. |
| 67 | M & L Green marble work 15 mm thick (table rubbed and polished) in steps, jambs, pillars, window cills, cooking platforms and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with marble shade of following typesnt with admixture of pigment to match the shade of granite stone including grinding and polishing complete over 15mm thick Screed bed or backing coat for laying floor finishes in CM 1:6 complete all as specified and directed. |
| 68 | Demolition of cement concrete as in ground floors and pavings not exceeding 15 cm thick below or above ground level (unreinforced) complete all as specified and directed. |
| 69 | M&L for pavings, with mix of fly ash, clinker & stone dust in the proportion of 1:3:6 (ie 10% fly ash, 30% clinker and 60% stone dust ) laying in layers n. exc 10cm thick, watering, ramming and compacted with hand/power roller 8 to 12 tonn roller to required camber and gradient complete all as directed by Engineer-in-Charge. |
| 70 | M&L for hardcore of gauge not exceeding 63 mm of broken stone, deposited, spread and levelled layers not exceeding 15 cm thick, watered and rammed to a true surface, complete all as specified and directed. |
| 71 | M&L for Chequered Cement concrete tiles 20cm x 20cm x 25mm thick, set jointed and pointed in neat cement slurry in floors over 15mm thick screed bed in cement mortar 1:6, with grey cement and pigment complete all as specified and directed. |
| 72 | M&L for Brickwork with flyash bricks, straight or curved on plan to any radius in half brick thick walls,built in CM 1:4, complete all as specified and directed. |
| 73 | M&L PCC (1:3:6) type B1 as in kerbs incl necessary form work (cast in situ) etc complete as directed. |
| 74 | Taking down carefully aluminium/Copper conductor point wiring (light , fan, socket or powr) complete including fittings such as switches, ceiling rose, pendents, regulators sockets etc and removing (except those to be reused shall be kept in safe custody at the site) andmaking good disturbed surfaces of walls, floors etc to match with the existing completeall as specified and directed. Please Enable Macros to View BoQ information |
| 75 | Taking down carefully aluminium/Copper conductor point wiring (light , fan, socket or powr) complete including fittings such as switches, ceiling rose, pendents, regulators sockets etc and removing (except those to be reused shall be kept in safe custody at the site) andmaking good disturbed surfaces of walls, floors etc to match with the existing completeall as specified and directed. Please Enable Macros to View BoQ information |
AI Tender Summary
Tender Timeline
Jul 10, 2026
11:30 IST
Tender Published
Tender notice published.
CompletedJul 30, 2026
17:00 IST
Bid Submission Deadline
Online submission via eProcurement portal.
Upcoming · 19 daysJul 31, 2026
Bid Opening Date
Technical bids will be opened and evaluated.
Upcoming · 20 daysTender Documents
Download All (ZIP) ↓
Disclaimer
We takes all possible care for accurate & authentic tender information. However users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender