Tender For Construction Of Lab Block & Academic Block Fst, At Cots Mirgund Skuast-K (Capex).
Tender Value
9.88 Crore
Estimated cost
Bid Submission
29 Jul 2026
2 days left
EMD
19.76 Lakhs
Bank guarantee accepted
Document Fee
20000
Non-refundable
Tender Type
Online
Tender Overview
Organization
Tender ID
Competition Type
NCB
Bidding Type
Tender
Location / State
Srinagar → Jammu and Kashmir
EMD Exemption
Not Available
Quantity
Not Available
Website
Contact Person
Address
Project Description
Tender for Construction Of Lab Block & Academic Block Fst, At Cots Mirgund Skuast-K (Capex).
Corrigendum
| Sr No | Corrigendum Date | Corrigendum | Type | New Submission Date |
|---|---|---|---|---|
| 1 | 16-Jul-2026 | corrigendum / addendum | Other | 29-Jul-2026 |
BOQ
| Sl. No. | Item Description |
| 1 | STRUCTURAL |
| 2 | EARTHWORK: Earth work excavation by mechanical means (hydraulic excavator) in trenches for foundations, drains, pipes, cables, etc (not exceeding 1.5 m in width) and for shafts, wells, cesspits and the like not exceeding 10 sqm on plan, including dressing of sides and ramming of bottoms lift up to 1.5m, including getting out excavated earth and disposal of surplus excavated earth as directed, within a lead of 50 metres, all kinds of soil. including Dewatering if any from Foundation upto Plinth level. |
| 3 | STONE SOLING: Providing and laying of hand packed stone soling (size 150 mm-230mm), before laying of mud mat, compacted, consolidated, rammed and filling the voids with fine sand - all complete incl carriage upto site of work with all head loads. |
| 4 | MUDMAT: Cast-in-situ of concrete work of nominal mix concrete M7.5 grade nominal maximum size of stone aggregate 40mm volumetric batching in foundation trenches and ground floor, including curing but excluding formwork costs. |
| 5 | MASS CONCRETE: Providing and laying mass concrete1:3:6 (1 cement : 3 coarse sand : 6 graded stone aggregate 20 mm nominal size) in Below Ground and Above Grouns Plinth retaining walls, (any thickness) including attached pilasters, including curing but excluding the cost of centring, shuttering and finishing with |
| 6 | CAST-IN-STU DESIGN MIX M25: Providing and laying in position machine batched and machine mixed design mix M-25 grade cement concrete for reinforced cement concrete work, using cement content as per approved design mix,incluyding pumping of concrete to site laying but excluding the cost of centering, shuttering, finishing and reinforcement, including admixtures in recommended proportiond as per IS:9103 to accelerate, retard setting of concrete, improve workability without impairing strength and durability as per direction of Engineer-in-charge. Note: - Cement in this item is @ 330 kg/ cum. Excess or less cement used as per design mix is content considered payable or recoverable seperately all works Below Plinth Levl / Above Plinth Level upto level V (AGL/BGL). |
| 7 | UPTO PLINTH LEVEL |
| 8 | ABOVE PLINTH LEVEL |
| 9 | FORM WORK: Centering and shuttering including strutting, propping etc. and removal of formwork from the site, for all works from foundations, to roof level |
| 10 | BELOW PLINTH LEVEL |
| 11 | ABOVE PLINTH LEVEL |
| 12 | SLAB EDGES |
| 13 | PLINTH FILLING: Supplying and filling in plinth with GSB/ Second class sand under floors including, watering, ramming, consolidating and dressing complete including carriage, leads and lifts. |
| 14 | BACK FILLING: Filling available excavated earth (excluding rock) in trenches, plinth, sides of foundations etc. in layers not exceeding 20 cm in depth, consolidating each deposited layer by ramming and watering, lead upto 50 m and lift upto 1.5 m. |
| 15 | STEEL REINFORCEMENT: Steel reinforcement for R.C.C. works including straightening, cutting, bending, placing in position and binding - all complete from foundation to roof level of Thermo-Mechanically Treated bars of grade Fe-500D or higher |
| 16 | STRUCTURAL STEEL:Structural steel work in built up sections, trusses and framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer all complete. plates, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer also included. |
| 17 | ANCHOR BOLTS: Providing and fixing mild steel round holding down bolts with nuts and washer plates complete. |
| 18 | ARCHITECTURAL |
| 19 | Brick work with common burnt clay (non-modular) bricks of class designation 7.5 in foundation and plinth including curing in: Cement mortar 1:6 ( 1 cement : 6 coarse sand) |
| 20 | Extra for brick work with common burnt clay bricks/cement concrete bricks in superstructure above plinth level upto floor five level |
| 21 | Half brick masonry with common burnt clay (non-modular) bricks of class designation 7.5 in foundations and plinth including curing in Cement mortar 1:4 ( 1 cement : 4 coarse sand) |
| 22 | Extra for half Brick masonry in superstructure above plinth level upto floor V level. |
| 23 | 12 mm thick cement plaster in 1:6 cement mortar in walls using coarse sand. Including curing and carriage |
| 24 | Pointing on exposed brick masonry external surfaces with lime surkhi finish (I Lime: 2 Surkhi ) mixing in approved proportion, including raking out joints, cleaning and preparation of surface, applying and finishing joints in ruled/pointed pattern as directed, curing, including grinding the brick surface where required, finishing true to line, level and plumb, complete in all respects including cost of all materials involved, including scaffolding/staging and all incidental charges as directed by the Engineer-in-Charge. |
| 25 | Providing and applying Plaster of Paris putty of 2mm thickness over plastered surface to prepare the surface even and smooth complete |
| 26 | Providing and applying white cement based putty of 2 mm thick, of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete. |
| 27 | Applying one coat of water thinnable cement primer of approved brand and manufacture on wall surface. |
| 28 | Wall Painting with acrylic emulsion paint of approved brand and manufacture to give an even shade. Two or more coats on new work |
| 29 | Providing and fixing Plaster of Paris (POP) cornice, 50 mm to 75 mm thick, in approved designs and patterns, including necessary moulding, finishing, jointing, scaffolding, all materials, labour and carriage complete in all respects as directed by the Engineer-in-Charge. |
| 30 | Finishing with Deluxe multi surface paint system for interiors and exteriors using primer as per manufacturers’ specifications, Painting steel work with deluxe multi surface paint of required shade to give an even shade. Two or more coats applied @ 0.90litre/10sqm over an under coat of primer applied @ 0.80litre/10sqm ofapproved brand and manufacture |
| 31 | Add for plaster drip course/grooves in plastered surface or moulding to R.C.C. projections |
| 32 | Providing and laying vitrified floor tiles in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS:15622 of approved make, in all colours and shades, laid on 20mm thick cement mortar 1:4 (1cement :4 coarse sand) including grouting the joints with white cement and matching pigments etc. complete Size of tile 600x600 mm |
| 33 | Providing and laying Vitrified tiles in different sizes (thickness to be specified by manufacturer), with water absorption less than 0.08 % and conforming to I.S. 15622, of approved make, in all colours and shades, in skirting, riser of steps, over 12 mm thick bed of cement mortar 1:3 (1 cement: 3 coarse sand), including grouting the joint with white cement and matching pigments etc. complete. |
| 34 | Providing and laying Polished Granite stone flooring in required designand patterns, in linear as well as curvilinear portions of the building all complete as per the architectural drawings with 18 mm thick stone slab over 20 mm (average) thick base of cement mortar 1:4 (1 cement : 4 coarse sand) laid and jointed with cement slurry and pointing with whitecement slurry admixed with pigment of matching shade including rubbing, curing and polishing etc. all complete as specified and as directed by the Engineer-in-Charge, Polished Granite stone slab jet Black, Cherry Red, EliteBrown, Cat Eye or equivalent. |
| 35 | Providing edge moulding to 18 mm/16 mm thick marble stone counters, Vanities etc. including machine polishing to edge to give high gloss finish etc. complete as per design approved by Engineer-in-Charge.Granite Work |
| 36 | Providing and laying vitrified floor tiles in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS:15622 of approved make, in all colours and shades, laid on 20mm thick cement mortar 1:4 (1cement :4 coarse sand) including grouting the joints with white cement and matching pigments etc. complete Size of tile 4'x8\\". |
| 37 | Providing and laying Anti skid floor tiles of size 600x600 mm or more (thickness to be specified by the manufacturer), of 1st quality conforming to IS : 15622, of approved make, laid on 20 mm thick cement mortar 1:4 (1Cement : 4 Coarse sand), including grouting the joints with white cement and matching pigments etc., complete. |
| 38 | Providing and fixing Ist quality Digital wall tiles conforming (thickness to be specified by the manufacturer), of approved make, in all colours, shades of 600x1200mm size as approved by Engineer- in-Charge, in linings of walls skirting, risers of steps and dados over 12 mm thick bed of cement mortar 1:3 ( 1 cement : 3 coarse sand) and jointing with grey cement slurry @ 3.3 kg per sqm, including pointing in white cement mixed with pigment of matching shade complete size of tile 600x1200mm |
| 39 | Grouting the joints of tiles having joints of 3 mm width, using epoxy grout mix of 0.70 kg of organic coated filler of desired shade (0.10 kg of hardener and 0.20 kg of resin per kg), including filling / grouting and finishing complete as per direction of Engineer-in-charge. |
| 40 | Providing and fixing Granite of any colour or shade gang saw cut, mirror polished, premoulded and prepolished, machine cut for kitchen platforms, vanity counters, window sills, facias and similar locations, of required size, approved shade, colour and texture laid over 20 mm thick base cement mortar 1:4 (1 cement : 4 coarse sand), joints treated with white cement, mixed with matching pigment, epoxy touch ups, including rubbing, curing, moulding and polishing to edges to give high gloss finish etc. complete at all levels 16mm thick |
| 41 | Extra for providing opening of required size and shape for wash basin/ kitchen sink in kitchen platform, vanity counters and similar location in marble/granite / stone work including necessary holes for pillar taps etc. including moulding, rubbing and polishing of cut edges etc. complete. |
| 42 | Providing and laying chisel dressed Devri Stone of size 300x200 mm face with 150 mm depth in cement mortar 1: 6 (1 cement : 6 coarse sand) upto plinth level including curing, one face dressed |
| 43 | Extra for providing rounded edges to chisel dressed Devri Stone steps have two faces dressed (treads) with nosing in cement mortar all complete as specified and as directed by the Engineer-in-Charge Rough chisel dressed |
| 44 | Providing and laying 25mm thick fini chiseled dressed Devri Stone of size as approved fixed with 20mm thick cement mortar 1: 4 (1 cement : 4 coarse sand) including curing, one face dressed complete job. |
| 45 | Providing and laying cement concrete in retaining walls, return walls, walls (any thickness) including attached pilasters, columns, piers, abutments, pillars, posts,struts, buttresses, string or lacing courses, parapets, coping, bed blocks, anchors blocks, plain window sills, fillets etcupto floor V level, including curing but excluding the cost of centring, shuttering and finishing with 1:3:6 (1 cement : 3 coarse sand : 6 graded stone aggregate 20 mm nominal size) |
| 46 | Supplying and applying waterproofing at plinth level, sunken portions etc. using pre applied, pressure sensitive HDPE membrane as per specifications listed below with guarantee period of 10 years: Supplying and installing of 1.2 mm thick self adhesive HDPE membrane conforming to BS 8102, IS 16471 Type I standard for below ground structures, having puncture resistance of 1000 N (as per ASTM E 154) and hydrostatic head resistance not less than 60 m head (ASTM D 5385), tensile strength of 25 Mpa (ASTM D 412), & elongation of min. 500% (ASTM D 412), peel adhesion to concrete of 880 N/m (As per ASTM D 903 modified). The membrane should be comprising of a min HDPE layer of 0.8 mm and a pressure sensitive adhesive layer which is covered by a weather proof protective and trafficable granular layer of sand to protect self adhesive polymer layer. Place the membrane HDPE film side to the substrate with adhesive facing towards the concrete pour. End laps should be staggered to avoid a build-up of layers. Leave the membrane loosely laid, in position until overlap procedure is completed. Accurately position succeeding sheets to overlap the previous sheet 75 mm along the marked selvedge and edges shall be sealed. Ensure the underside of the succeeding sheet is clean, dry and free from contamination before attempting to overlap. At the end of each role, the grains should be removed by using hot air shovel gun & the joint between two sheets should be sealed with the help of double side tape. |
| 47 | Making plinth protection 50mm thick of cement concrete 1:3:6 (1 cement : 3 coarse sand :6 graded stone aggregate 20 mm nominal size) over 75mm bed of dry brick ballast 40mm nominal size well rammed and consolidated and grouted with fine sand including finishing the top smooth and curing complete |
| 48 | Providing and laying in position specified grade of reinforced cement concrete including curing but excluding the cost of centering, shuttering, finishing and reinforcement. 1:1½:3 (1 cement : 1½ coarse sand : 3 graded stone aggregate 20 mm nominal size) |
| 49 | Centering and shuttering including strutting, propping etc. and removal of form for: Shelves (cast-in-situ) |
| 50 | Lintel, beams, plinth beams, girders, bressumers and cantilevers. |
| 51 | Providing and fixing Track deck CRIL make or equivalent H.I. rib profiled sheets 1000 to 1020 mm cover width 28-35 mm high crests at 250 to 255 mm T.C.T(total coated thickness) high tensile S.M.P Galvalume steel. The sheets shall have wide panes with 3 no stiffing ribs, effective water shedding and special male/female ends with full return legs on side Lapps for purlins support and anti-capillary flute inside Lapp. The sheets shall have a hot dip metallic coated of zinc and aluminum (150 gms /sm) zinc/aluminum coating mass total on both sides AZ-150 as IS -1397 ,550 MPA yield stress. Providing silicon modified polyester coating of approved colour of total thickness of 35 micron comprising 20 micron exterior coat of S.M.P over 5 micron polyester back coat over 5 micron primer coats on both surfaces including side and end Lapp and using 8mm Galvalume hex self-drilling fastener on each crest of sheet for connection with purlins and seam bolts at 300mm centers on all sides and end Lapps etc (.measured for unit of laid area) (0.50 mm thickness ) |
| 52 | Providing and fixing precoated galvanised steel sheet roofingaccessories0.50 mm (+0.05 %) total coated thickness, Zinc coating 120grams per sqm as per IS: 277, in 240 mpa steel grade, 5-7 microns epoxyprimer on both side of the sheet and polyester top coat 15-18 micronsusing self drilling/ self tapping screws complete :Ridges/Valley plain (500 - 600mm) |
| 53 | Providing and fixing thermal insulation of ceiling (under deck insulation) with specified glass wool conforming to IS: 8183, 50mm thick, wrapped in 200 G Virgin Polythene bags fixed to ceiling with metallic cleats (50x50x3mm) @ 60cm c/c and wire mesh of 12.5mm x 24g wire for top most ceiling of building. With resin bonded rock wool with density 48 kg/cum |
| 54 | Providing and fixing factory made uPVC white colour casement/casement cum fixed glazed windows comprising of uPVC multi-chambered frame, sash and mullion (where ever required) extruded profiles duly reinforced with 1.60 ± 0.2 mm thick galvanized mild steel section made from roll forming process of required length (shape & size according to uPVC profile), uPVC extruded glazing beads of appropriate dimension, EPDM gasket, stainless steel (SS 304 grade) friction hinges, zinc alloy (white powder coated) casement handles, G.I fasteners 100 x 8 mm size for fixing frame to finished wall, plastic packers, plastic caps and necessary stainless steel screws etc. Profile of frame & sash shall be mitred cut and fusion welded at all corners, mullion (if required) shall be also fusion welded including drilling of holes for fixing hardware's and drainage of water etc. After fixing frame the gap between frame and adjacent finished wall shall be filled with weather proof silicon sealant over backer rod of required size and of approved quality, all complete as per approved drawing & direction of Engineer-in-Charge. ) Note: For uPVC frame, sash and mullion extruded profiles minus 5% tolerance in dimension i.e. in depth & width of profile shall be acceptable. Variation in profile dimension in higher side shall be accepted but no extra payment on this account shall be made. Casement window (Two track) single/Double panel with S.S. friction hinges (300 x 19 x 1.9 mm), made of (small series), with fly proof SS wire mesh and 6mm thick toughned glass frame 47 x 50 mm & sash 47 x 68 mm both having wall thickness of 1.9 ± 0.2 mm and single glass pane glazing bead of appropriate dimension. |
| 55 | Providing wood work in frames of doors, windows, clerestory windows andother frames, wrought framed and fixed in position with hold fast lugs or withdash fasteners of required dia and length (hold fast lugs or with dash fasteners shall be paid for separately):Second class deodar wood |
| 56 | Providing and fixing ISI marked flush door shutters conforming to IS: 2202 (Part I) decorative type, core of block board construction with frame of 1st class hard wood and well matched teak 3 ply veneering with vertical grains or cross bands and face veneers on both faces of shutters. With ISI marked M.S. pressed butt hinges bright finished of required size with necessary screws |
| 57 | French spirit polishing, Two or more coats on new works including a coatof wood filler |
| 58 | Providing and fixing Hardware fittings of approved including cost of screws etc all complete |
| 59 | Aldrop 300 mm brass heavy type |
| 60 | Aldrop 250 mm brass heavy type |
| 61 | Brass Handles 600 mm long |
| 62 | Brass Handles 200 mm long |
| 63 | Brass Handles 150 mm long |
| 64 | Providing and fixing bright finished brass tower bolts (barrel type) with necessary screws etc. complete. : 150mm |
| 65 | Providing and fixing double action hydraulic floor spring of approved brand and manufacture IS : 6315 marked, having brand logo embossed on the body/plate with double spring mechanism and door weight upto 125 kg for doors including cost of cutting floors, embedding in floors as required and making good the same matching to the existing floor With Stainless Steel cover plate minimum 1.25 mm thickness. |
| 66 | Providing and fixing stainless steel (Grade 304) railing made of Hollow tubes channels, plates etc. including welding ,grinding, buffing, polishing and making curvature (wherever required) and fitting the same with necessary stainless steel nuts and bolts complete ,including fixing the railing with necessary accessories and stainless steel dash fasteners, stainless steel bolts etc. of required size, on the top of the floor or the side of waist slab with suitable arrangement as per approval of Engineer-in-charge. The job includes Railing as per per Arch design and Hand rail for the staircases. |
| 67 | Providing and fixing aluminum work for doors, windows, ventilators and partitions with extruded built up standard tubular sections/appropriate Z sections and other sections of approved make conforming to IS: 733 and IS: 1285, fixed with dash fastener of required dia. and size including necessary filling up of gaps at junctions i.e, at top, bottom and sides with required EPDM rubber / neoprene gasket felt etc. Aluminum sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminum snap beading for glazing / panelling, C.P. brass / stainless steel screws, all complete as per architectural drawings and the directions of Engineer-in-Charge including cost 5mm thick glazing, 12mm thick particle board panelling and dash fasteners etc all complete.) |
| 68 | Note:-The rates quoted are inclusive of all carriages of materials (Mechanical/Manual) from source to site work and all extra charges including dewatering if any during the execution of work complete in all respects. Please Enable Macros to View BoQ information |
AI Tender Summary
Tender Timeline
Jul 16, 2026
11:30 IST
Tender Published
Tender notice published.
Completed
Jul 29, 2026
18:00 IST
Corrigendum-1 Issued
Clarifications on tender conditions and amendments issued.
Upcoming · 2 daysJul 29, 2026
17:00 IST
Bid Submission Deadline
Online submission via eProcurement portal.
Upcoming · 2 daysTender Documents
Download All (ZIP) ↓
Disclaimer
We takes all possible care for accurate & authentic tender information. However users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender