Tender For Special Repair To Flooring , Ceiling And Other Misc Works In Bldg No. T- 279 At Ciw, Meg & Centre Under Ge (North) Bangalore
Tender Value
1.10 Crore
Estimated cost
Bid Submission
06 Aug 2026
26 days left
EMD
1.85 Lakhs
Bank guarantee accepted
Document Fee
1000
Non-refundable
Tender Type
Online
Tender Overview
Organization
Tender ID
Competition Type
NCB
Bidding Type
Tender
Location / State
Bengaluru Urban → Karnataka
EMD Exemption
Not Available
Quantity
Not Available
Website
Contact Person
Address
Project Description
Tender for Special Repair To Flooring , Ceiling And Other Misc Works In Bldg No. T- 279 At Ciw, Meg & Centre Under Ge (North) Bangalore
BOQ
| Sl. No. | Item Description |
| 1 | Demolition of cement concrete and paving not exceeding 15 cm thick (below or above ground level) complete all as specified and as directed. |
| 2 | Taking down chowkats or frames with shutters (without taking off shutter from frames) not exc. 1.5 sqm each including making good the disturbed surfaces to match with the adjoining surfaces etc complete all as specified and as directed |
| 3 | Taking down chowkats or frames with shutters (without taking off shutter from frames) exc. 1.5 Sqm but n exc 4 Sqm each including making good the disturbed surfaces to match with the adjoining surfaces etc complete all as specified and as directed |
| 4 | Dismantling wrought iron or mild steel work of any description not otherwise provided for etc complete all as specified and as directed |
| 5 | M&L for Rolled mild steel sections as in main and cross beams, hip and jack rafters; purlins where connected to common rafters and running rails and guides for sliding doors; fixed with angle cleats or other connecting plates confirming to Fe 410 -W (Gde- E- 250) quality-A etc complete all as specified and as directed |
| 6 | Dismantling plain or corrugated steel sheeting any gauge, thickness in roof covering complete all as specified and as directed |
| 7 | S&F Pre-painted galvatume aluminum zinc coating GI based corrugated steel sheet 0.50mm thick of any colour having tensile strength of 550 MPA, 150 AZ, as in roof covering / cladding to wall, fixed with self tapping screws etc complete all as specified and as directed |
| 8 | M&L for Plain cement concrete (1:4:8) type D- 2 using 40mm graded stone aggregate as in 75 mm thick sub base to flooing etc complete all as specified and as directed |
| 9 | M & L for Cement concrete designer chequered tiles , exterior grade, coloured glossy finish rubber pressed of size 20cm x 20cm x 25mm thick set, jointed and pointed in neat cement slurry with grey cement and pigment to match the shade / colour / matrix of tiles over and including screed bed or bedding layer 15mm thick in cement mortar (1:6) including demolition of existing stone slab laid bedded and pointed in any mortar etc complete all as specified and as directed. |
| 10 | M&L for Plain cement concrete (1:2:4) type B-0 using 12.5 mm graded stone aggregates as in 25 mm thick sub base to flooring etc complete all as specified and as directed |
| 11 | M&L for Plain cement concrete (1:3:6) type C-1 using 20 mm graded stone aggregates as in 75 mm thick plinth protection finished fair & even without using extra cement including filling joints with sealing compound grade 'A' etc., complete all as specified and directed. |
| 12 | M&L for Vitrified Ceramic tiles light shade 10 mm thick (square / rectangular) polished, area of each tiles exceeding 0.42 sqm but not exceeding 1.00 sqm, in floors etc., set and jointed in neat cement slurry and pointed in white or coloured cement to match over & including 15 mm thick screed bed in cement mortar (1:6) including dismantling floor, hearth etc., complete all as specified and as directed |
| 13 | M&L for Vitrified Ceramic tiles light shade 10 mm thick (square / rectangular) polished, area of each tiles exceeding 0.42 sqm but not exceeding 1.00 sqm, in skirting / dado etc., set and jointed in neat cement slurry and pointed in white or coloured cement to match over & including 10 mm thick backing coat in cement mortar (1:4) including dismantling existing wall tiling etc., complete all as specified and as directed |
| 14 | Demolition of stone slabs tiles of any description or thickness in floors aprons laid bedeed and pointed in any mortar etc., complete all as specified and as directed |
| 15 | M&L for Heavy duty vitrified coloured tiles of size 600mmX600mmX15 to 16mm thick in floors, hard stone finish, etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match over & including 15 mm thick screed bed in cement mortar (1:6) complete all as specified and as directed (Make : Somary (Hard Stone) / Johnson (Meteor Series). |
| 16 | M&L for Heavy duty vitrified coloured tiles of size 600mmX600mmX15 to 16mm thick in skirting / dado, hard stone finish, etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match over & including 10 mm thick backing coat in cement mortar (1:3) complete all as specified and as directed (Make : Somary (Hard Stone) / Johnson (Meteor Series). |
| 17 | S&F Factory made pressed steel door frame of profile size 125 X 60 mm, made with 1.25mm thick M S sheet, with one ore more rebate includings necessary fixing lugs, hinges, locks strike plate etc complete all as specified and as directed |
| 18 | M&L for Plain cement concrete (1:3:6) type C-1 using 20mm graded stone aggregate as in hold fast block and filling in pressed steel chowkat including necessary formwork etc complete all as specified and as directed |
| 19 | S&F Flush shutter 35mm thick solid core construction with decorative choice lamination both sides of shutter, kiln seasoned and chemically pressure treated complete all as specified and as directed |
| 20 | S&F Glazed skeleton shutters 35 mm thick, factory made second class hardwood, open rebated and prepared to receive glass, gauze, etc. (without sash bars), edges of framing plain, chamfered or rounded. fitted with cut and mitred beads for securing glass etc.; sizes of members of shutters as specified in SSR Part I, Section 8, clause 8.24 (a) etc complete all as specified and as directed |
| 21 | S&F Steel window Box type double side shutters (Windows side hung type , Ventilators top hung) fabricated with pressed steel frames made out CRC Sheet of 80x60x1.25mm double rebated, Shutters box type made out of CRC Sheet of 40x20x1.0mm, windows & ventilator shutter fixed fixed with box type hinges, Aluminium die cast handles for glass shutters, Iron flat type handles for mesh shutters, Telescopic stays, etc including 12mm square guard bars/grill welded with steel frame (100c/c horizontally) all as specified and directed.NOTE: (i) unit rate quoted shall deemed to included steel frames, steel shutters, Guard bar/Grill, beading, fittings such as handles, hinges,Telescopic stays, locking arrangements and fixing of glass and wiremesh etc. (ii) Supply only sheet glass and stainless steel wire mesh will be measured and paid separately. (iii) All Windows / Ventilator shall be all as per CECZ TD drg No 539) |
| 22 | S&F Sheet glass 4mm thick ordinary quality and glazing with oil putty or wooden beading to wooden frame or steel frame in squares not exc 0.50 sqm in each pane complete all as specified and as directed |
| 23 | S&F Stainless steel wire cloth 0.36 mm nominal dia of wire and average width of aperature 1.40 mm and fixed with stainles steel wire stapel etc complete all as secified and as directed |
| 24 | S&F Aluminium anodised tower bolt 200 mm long of extruded section etc complete all as specified and as directed |
| 25 | S&F Aluminium handle 150 mm size, cast type, anodised etc complete all as specified and as directed |
| 26 | S&F Floor door stopper of aluminium alloy body and tongue, anodised, with hard drawn steel spring, overall length of cover plate150 mm, fixed in floor etc complete all as specified and as directed |
| 27 | S&F Aluminium alloy, anodised sliding door bolt 300 mm long with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded section and fixing bolts and sliding bolts of extruded section or cast aluminium alloy etc complete all as specified and as directed |
| 28 | S & F CPVC pipes 25mm outer dia, SDR 11 & Plain CPVC SDR 11 fittings on walls/ ceiling or laying in floors including taking down existing GI/CPVC pipe line etc complete all as specified and as directed |
| 29 | S & F in repairs Rotational moulded polythene water storage tank 1000 ltrs capacity (cylindrical vertical with closed top) hoisted and fixed in position all as specified in SSR part I including ball float valves high pressure of PTMT with epoxy coated aluminium rod & high density plastic ball 25 mm dia of bore etc complete all as specified and directed |
| 30 | S & F in repairs Gun metal, globe or gate valve with iron wheel head screwed both ends for iron pipe 25 mm dia bore all as specified and as directed. |
| 31 | Taking down cement plaster of any description hacking for key or raking out joint on old brick work / stone / concrete surface etc complete all as specified and as directed. |
| 32 | M&L for Rendering 15mm thick cement mortar (1:6) on fair faces of brick or concrete wall surfaces finished even and smooth without using extra cement complete all as specified and as directed. |
| 33 | M&L for rendering for ceiling 5 mm thick in CM 1:3 on fair faces of brick work or concrete surface finished even and smooth without using extra cement etc complete all as specified and as directed |
| 34 | M&L for preparation of New plastered ceiling surface and applying two coats Acrylic emulsion distemper, white or tinted over a coat of self primer complete all as specified and as directed |
| 35 | M&L for Preparation of new plastered wall suface and applying two coats Acrylic emulsion distemper, white or tinted over a coat of self primer complete all as specified and as directed |
| 36 | Complete removal exising treatment by means of wire brushing, sand paper, manually or mechanically up to visible of plastered surface including rubbing and washing etc complete all as specified and as directed |
| 37 | M&L for preparation of wall surface with sand paper etc to obtain smooth surface and applying 1mm thick wall care putty finished to smooth surfaces etc complete all as specified and as directed |
| 38 | M&L for Preparing old plastered suface of walls and applying two coats of Acrylic emulsion distemper white or tinted over a coat of self primer etc complete all as specified and as directed |
| 39 | M&L for preparing old ceiling surface and applying two coats of Acrylic emulsion distemper white or tinted over a coat of self primer etc complete all as specified and as directed |
| 40 | M & L for preparation of new or old plastered surface of wall and applying two coats of 100% Premium acrylic weather proof exterior emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives @ 1.43 litre/ 10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/ 10 sqm etc., complete all as specified and as directed |
| 41 | M&L for Preparation of new or previously un-treated steel and iron surfaces of any description, over 10 cm in width or girth, not otherwise described and painting with two coats of synthetic enamel paint over a coat of red oxide primer etc complete all as specified and as directed |
| 42 | S&F in repairs stainless steel decorative curtain rod of 25 mm dia bore including fancy finale caps cap (02 nos in each curtain rod) etc complete all as specified and as directed |
| 43 | S&F in repair Brass Chromium Plated designer Bracket for curtain rod of dia 25 mm dia made out of stainless steel flat not less than 20 mm wide 1.50 mm thick and overall length not less than 160 mm fixed with screws min 2 Nos with Rawl Plug of size not less than 50 mm long etc complete all as specified and as directed |
| 44 | S&F in repairs false ceiling with grid suspended system of size 600X600mm standard section consisting of wall angle 25x25mm, main T sec25x40mm, cross Tee 25mm x 25mm as per manufacturer instruction / catalogue , ceiling suspended with 3 mm dia GI wire hanger fixed with steel dash fastner, butter fly clips, hold down clips etc (Main corner, cross tee& wall angle of MS galvanized with PPPCGS) including 4 mm thick High pressure Steam Curing (HPSC) self textured design pre primered non asbestos fibre cement building boards fixed to false ceiling etc complete all as specified and as directed |
| 45 | M&L Pre-cast Cement concrete (1:3:6 ) type C-1 using 20 mm graded stone aggregates as in solid block masonary exc 10 cm in width and setting in CM (1:6) including demolition of brick Work / Stone Masonry / PCC block masonry built in cement mortar of any description all as specified and directed. |
| 46 | M&L for PCC (1:4:8) type D-2 using 40mm graded stone aggregate as in foundations, filling and mass concrete, complete all as specified and directed. |
| 47 | M&L for Cement concrete (1:2:4) type B-0 using 12.50mm graded stone aggregate as in copings, parapets and railing upto 60cm height, leveling concrete for Roof slab, kerbs, water troughs/Chajjas and the like including weathering, slightly rounded or chamfered angles and throating, necessary formwork complete all as specified and directed. |
| 48 | M&L for screed bed 10 mm thick in CM (1:3) mixed with water proofing compound finished even & smooth without using extra cement to receive roof tratement etc complete all as specified and as directed Notes: WPC will be measured and paid seperately . |
| 49 | M&L for water proofing treatment over roof surfaces all as per following specification complete all as specified and as directed :-(i) Removing all loose gravel, dirt, oil, grease and foreign materials by jet or dry air, cleaning the surfaces mechanically or by grinding to make the surface smooth(ii) Applying compatible oil bound bitumen primer @ 0.30 Kg/Sqm (iii) Laying 3 mm thick APP modified water proofing membrane weighing not less than 3.8 kg/sqm reinforced with non woven polyester matt weighing not less than 150 gm /sqm having softening point not less than 140 centigrade, having tensile strength of 650N /sqm and 350 N/sqm in longitudinal and transverse directions respectively of the reinforced tearing strength of 180N by torch application with minimum 10cm side overlap and 15cm end lap.(iii) Applying solar reflective bituminious aluminium paint @ 0.10 Kg/Sqm.(iv) Pond test for 72 hours shall be carried out for dampness / leakage test. |
| 50 | Supply only water proofing compound (Liquid), ISI marked, complete all as specified and as directed. |
| 51 | Removing debris building materials etc. to a distance of exc 900 mtr but not exc 1.00 Km, including loading, unloading and stacking at the destination etc complete all as specified and as directed |
| 52 | Taking down carefully aluminium / copper wiring/power point wiring (light, fan, socket or power) complete including fittings such as switches ceiling roses, regulators, sockets, light fittings, fans etc and making good the disturbed surface of walls, ceiling etc including making good to match with adjoining surfaces complete all as specified and as directed. |
| 53 | M & L for Surface Point Wiring with single core PVC insulated unsheathed FRLSH 1.5 Sqmm multi stranded copper conductor cable 1100 volts grade conforming to IS 694 drawn through and including non-metalic rigid PVC conduit with accessories surface type run on walls/ ceiling including MS terminal boxes fabricated with 1.6 mm thick MS sheet concealed on walls with plastic laminated sheet top cover 3 mm thick fixed with cadmium plated iron screws for housing the switches, switch socket outlets, fan regulators etc., including 1.5 Sqmm PVC insulated single core multi stranded copper conductor cable as earth continuity conductor and connecting to common earth dolly for following all as specified and as directed :- |
| 54 | One light / fan point controlled by one switch |
| 55 | One light point controlled by two way switch |
| 56 | One 3 pin socket out let 5 Amps on independent board |
| 57 | M & L for surface Point Wiring with single core PVC insulated unsheathed FRLSH 2.5 Sqmm multi stranded copper conductor cable 1100 volts grade conforming to IS 694 drawn through and including non-metalic rigid PVC conduit with accessories surface type run on walls / ceiling including M S terminal boxes fabricated with 1.6 mm thick MS sheet concealed on walls with plastic laminated sheet top cover 3 mm thick fixed with cadmium plated iron screws for housing the switches, switch socket outlets, fan regulators etc., including 2.5 Sqmm PVC insulated single core multi stranded copper conductor cable as earth continuity conductor and connecting to common earth dolly all as specified and as directed. |
| 58 | Note for Item No. 53 & 54 :-(i) The earth wire for the points in the same circuit can be looped from point to point(ii) Earth wire shall be taken inside the conduit(iii) Cost of terminal box is deemed to be included in the item rate quoted for point wiring(iv) Cost of a circuit of any length of cable from DB to any switch/ socket board to be included in point wiring. |
| 59 | S&F LED batten with luminaire 20 Watts capacity, 4 feet long suitable for indoor applications with extruded aluminium housing & integrated LED channel complete with all accessories all as specified and directed. |
| 60 | S&F Switch piano flush type single pole one way 5 Amps 230Volts all as specified and directed. |
| 61 | S&F Switch piano flush type single pole, two way 6 Amps, 230Volts all as specified and directed. |
| 62 | S&F Stepped type electronic fan regulator, flush, Switch/socket type, 230volts all as specified and as directed |
| 63 | S&F Switch socket combination 2 in 1 , 5 Amps flush type, 230volts all as specified and as directed |
| 64 | S&F Switch socket combination 2 in 1, 3 pin, 5 and 15 Amps flush type, 230volts universal all as specified and as directed |
| 65 | S&F in repairs MCB SPN, 32 Amps capacity 240 volts, 'C' series complete all as specified and as directed |
| 66 | S&F in repairs MCB single pole 10/16/20/32 Amps, 'C' series, 240 volts complete all as specified and as directed |
| 67 | S&F in repairs MCB Distribution Board, SPN 8 way, double door type 240 volts with 200 Amps rated busbar as specified and as directed. |
| 68 | S&F in repairs MCB Distribution Board, TPN 4 way, double door type 240 volts with 200 Amps rated busbar as specified and as directed. |
| 69 | S&F in repairs MCB TPN 63 Amps, 415 volts 10 KA, 'C' series complete all as specified and as directed |
| 70 | S&F in repairs Ceiling rose, surface bakelite type 65 x 50 mm, 3 terminals, 230volts all as specified and as directed |
| 71 | M & L for Sub main wiring with two runs of single core 6 Sqmm 1100 volts grade multistranded FRLS copper conductors cable along with 6 Sqm PVC insulated single core multistranded copper conductor cable as earth continuity conductor run through & including suitable size of PVC conduit and removing old existing submain wiring complete all as specified and as directed |
| 72 | M&L for Earthing with galvanized steel earth plate electrode 60 cm x 60 cm x 6mm thick buried directly in ground vertically to a depth not less than 2.25 mtr below ground level with top edge of earth plate at a depth not less than 1.5 mtr connected to galvanized earth lead wire 4 mm dia as earth lead up to 7.5 mtr long by means of nuts, bolts, thimbles,check nuts and washers etc made of galvanized iron connected to earthing test point all as shown in electrical plate No 3 of SSR Part-I and as specified or indicated and testing on completion including necessary earth work and excavation in any type of soil, PCC (1:3:6) type C1 chamber, pre cast slab 40mm thick in cement concrete (1:2:4) type B1 with 8 mm dia TMT bars reinforced at 10 cm centre to centre both ways, funnel with watering pipe, wire mesh, lugs, test point including dismantaling old un-serviceable earthing complete all as specified and as directed |
| 73 | Supply and fixing LED bldg security light fitting 30 Watts capacity, pressure die cast housing along with prismatic polycarbonate difuser with IP 66 protection, single piece and secondary lens delivering 120 lm/W, complete all as specified and as directed |
| 74 | S & F in repairs G I bracket made out of GI tubing medium grade 25 mm dia bore, approx length 1.5 m long including MS clamps made out of M S flat iron 25 x 6 mm, nuts & bolts, washers etc and including applying two coats of aluminum paint over a coat of red oxide primer complete all as specified and directed. Please Enable Macros to View BoQ information |
AI Tender Summary
Tender Timeline
Jul 09, 2026
11:30 IST
Tender Published
Tender notice published.
CompletedAug 06, 2026
17:00 IST
Bid Submission Deadline
Online submission via eProcurement portal.
Upcoming · 26 daysAug 13, 2026
Bid Opening Date
Technical bids will be opened and evaluated.
Upcoming · 33 daysTender Documents
Download All (ZIP) ↓
Disclaimer
We takes all possible care for accurate & authentic tender information. However users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender