Tender For Addition Alteration To To Bldg No P 70, P 72 And Provn Of Hay Store Shed At Chandimandir
Tender Value
19.37 Lakhs
Estimated cost
Bid Submission
29 Jul 2026
16 days left
EMD
38740
Bank guarantee accepted
Document Fee
500
Non-refundable
Tender Type
Online
Tender Overview
Organization
Tender ID
Competition Type
NCB
Bidding Type
Tender
Location / State
Panchkula → Haryana
EMD Exemption
Available
Quantity
Not Available
Website
Contact Person
Address
Project Description
Tender For Addition Alteration To To Bldg No P 70, P 72 And Provn Of Hay Store Shed At Chandimandir
BOQ
| Sl. No. | Item Description |
| 1 | Taking down existing plaster of any description on brick wall/ concrete surface including racking out joints, hacking for key, scrubbing down with water etc complete, all as specified and directed. |
| 2 | Demolition of brickwork or stone/ boulder masonry, built in cement mortar including all quoins, arches, pillars, etc. but excluding ashlar facings, dressed stonework and precast concrete articles complete all as specified and directed. |
| 3 | Brick work with sub class ‘B’ bricks of old size bricks, straight or curved on plan exc 6 metre mean radius built in cement mortar 1:6 complete all as specified & directed. |
| 4 | 15mm thick rendering in Cement and Sand mortar 1:6 over brick or concrete surfaces finished even and smooth without using extra cement complete all as specified and directed |
| 5 | 15mm thick rendering in Cement and Sand mortar 1:4 over roof slab finished even and fair mixed with water proofing compound as per manufacturer's instructions complete all as specified.Note : WPC shall be measured and paid separately. |
| 6 | Preparation of new or previously untreated steel surfaces of any description, not otherwise described, over 10 cm width or girth and applying two coats of Synthetic enamel paint (Ordinary tint) complete all as specified and directed. |
| 7 | Dismantling timber scantling exc 40 Sqcm in section in any position unframed work & removing from site complete all as specified and directed. |
| 8 | Mild Steel work in tubular trusses including special shaped washer etc. complete using ERW or induction butt welded tubes conforming to I. S.1161- 1979 grade St.-240, complete all as specified & directed by Engineer-in-Charge |
| 9 | Dismantling of asbestos cement (corrugated, semi corrugated, etc.) sheets in roof coverings and removal, complete all as specified and directed. |
| 10 | Pre-painted galvalume aluminium zinc (AZ-70) coating GI based corrugated steel sheeting 0.50 mm thick any colour having tensile strength 550 Mpa as in roof coverings/cladding to wall, fixed with self tapping screws etc, complete all as specified & directed by Engineer-in-charge. |
| 11 | Dismantling of wall and ceiling board (fibre, pulp insulation etc) any thickness including cover fillet & removing from site complete all as specified and directed |
| 12 | Powder coated GI Frame work grid Size of grid 605 x 605mm for ceiling comprising of Gl periMetre channel 0.55 mm thick with two unequal flanges of 20 and 30 mm and web of 27 mm, fixed to surrounding wall using nylon sleeves and screws at 450 mm centre to centre/intermediate channel 0.9 mm thick having two equal flanges of 15 mm each and web of 45 mm suspended from soffit at approx 900 mm centre to centre with Gl cleat and steel expansion fasteners with and including ceiling section (not exc 1.2 m length) of 0.55 mm thickness having kurled web of 50 mm and flange of 26 mm each with lips of 10.5 mm fixed to the intermediate channel with connecting clips across the intermediate channel at 457 mm centre to centre with hangers 6 mm dia. G.I. (upto 1200mm length) adjusting level fixed to roof by means of ceilling cleats made out of G.I. flat 40 x 3 mm size 60mm long and expansion hold fasteners 12.5mm dia, 40mm long, complete all as specified and directed |
| 13 | 4mm thick Non asbestos fibre cement building boards fixed or laid/ inserted to timber/GI/Aluminium framework with screws fixed in ceiling flat or sloping complete all as specified. |
| 14 | 5mm thick rendering in Cement and Sand mortar 1:3 on ceiling, chajja surfaces (concrete surfaces) finished even and smooth without using extra cement, complete all as specified and directed. |
| 15 | Supply only Liquid water proofing compound complete all as specified and as directed by Engineer-in-Charge. |
| 16 | Preparing old plastered surfaces of ceiling by rubbing down and stopping of painted surfaces and aplying two coat of distemper oil emulsion complete all as specified and directed. |
| 17 | Preparation of New decorated wall surfaces of ceiling and applying two coats of oil bound distemper over a coat of chalk whiting, complete all as specified and directed. |
| 18 | Preparation of new plastered surfaces of walls by washing, rubbing down and stopping of painted surfaces and applying two coats of cement base paint, complete all as specified and directed. |
| 19 | Preparation of old surfaces of walls and applying two coats of cement base paint, complete all as specified and directed |
| 20 | Preparing Newly plastered surfaces of wall and aplying two coat of distemper oil emulsion over a coat of Chalk whiting, on plastered surfaces, prepara-tory to distempering complete all as specified and directed. |
| 21 | Preparing old plastered surfaces of wall by washing, rubbing down and stopping of painted surfaces and aplying two coat of distemper oil emulsion complete all as specified and directed. |
| 22 | 75mm thick plain cement concrete type C-1 1:3:6 (Using 20mm graded crushed stone aggregates) as in plinth protection finished fair and even without using extra cement complete all as specified and directed. |
| 23 | Non skid ceramic coloured tiles, 7 to 8 mm thick (square/ rectangular) area or each tile exceeding 0.18 sqm but not exceeding 0.38 sqm, in floors etc set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tile, over and including 15mm thick screed bed in cement mortar 1:4 complete all as specified and directed. |
| 24 | Non skid ceramic coloured tiles 7 to 8 mm thick square/rectangular) area of each tile exc 0.18 sqm but not exceeding 0.38 sqm, in skirting /dado etc., set and jointed in neat cement slurry and pointed in white or Coloured cement to match over and including 10 mm thick bedding layer in CM 1:6, complete all as specified and directed. |
| 25 | Taking down chowkhats or frame n.exc 1.5 Sqm with shutter (without taking off shutters from the frame) and removal from site complete all as specified & directed. |
| 26 | Taking down chowkats or frame exc. 1.5 Sqm and n exc 4 Square metre with shutters, without taking off shutters from the frame, complete all as specified and directed. |
| 27 | Pressed steel frames 125mm x 60mm for doors with one or more rebates including necessary fixing lugs, hinges, lock strike plate, etc, including filling of PCC 1:3:6 in hollow frame complete all as specified and directed. |
| 28 | 30mm thick flush shutters, solid core construction, with block board core & plywood face panels, commercial type on both sides all as specified & directed by Engineer-in-charge. |
| 29 | 35 mm thick second class hard wood glazed and skeleton shutters open rebated and prepared to receive gauge/ glass etc, edges of framing plain chamfered or rounded fitted with cut and mitred beads for securing glass etc complete all as specified and directed. |
| 30 | Galvanised mild steel wire cloth 0.56 mm nominal dia of wire & avg width of aperture 1.18 mm in fixed with stainless steel wire staples, complete all as specified and directed. |
| 31 | 150 mm size aluminium anodized, barrel tower bolt of extruded section and fixed complete all as specified and directed. |
| 32 | 150mm Extruded aluminium alloy handle fabricated type, complete all as specified and directed. |
| 33 | Aluminium alloy, anodized, sliding door bolt 250mm long hasp , staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast aluminum alloy and fixed, complete all as specified and directed. |
| 34 | 300mm MS ordinary rat tail rod pattern spring incl roller plate complete all as specified and directed. |
| 35 | Preparation of new or previously untreated wood and wood based surfaces of any description, not otherwise described, over 10 cm width or girth and applying two coats of Synthetic enamel paint (Ordinary tint) over a coat of Pink primer complete all as specified and directed. |
| 36 | Floor door stopper of aluminium alloy body and tongue, anodized with hard drawn steel spring, fixed in floor (140mm size), complete all as specified and directed. |
| 37 | Powder coated aluminium (minimum thickness of powder coating 50 micron) work for doors, windows, ventilators, chowkhats and partitions (Fixed portions) with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS:1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing/ paneling, C.P. brass/ stainless steel screws, all complete as per architectural drawings and the directions of Engineer-in-Charge |
| 38 | Powder coated aluminium (minimum thickness of powder coating 50 micron) for shutters of doors, windows & ventilators including providing and fixing hinges/ pivots and making provision for fixing of fittings wherever required including the cost of EPDM rubber/neoprene gasket required (Fittings shall be paid for separately) with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS:1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing/ paneling, C.P. brass/ stainless steel screws all complete as per architectural drawings and the directions of Engineer-in-charge. |
| 39 | Powder coated aluminium Decorative grill (minimum thickness of powder coating 0 micron) of approved design / pattern (Aperture of grill should not be more than 75mm) with approved standard section and fixed to the existing window frame with C.P. brass/ stainless steel screws @ 200mm center to center, including cutting the grill to proper opening size for fixing and operation of handles and fixing approved anodized aluminium standard section around the opening , including aluminium ‘U’ channel and all necessary fitting complete all as per requirement of Engineer-in-Charge. |
| 40 | 4.00mm thick ordinary quality tinted glass, fixed to aluminum frame work ,in panels exc 0.5 Sqm in each pane, complete all as specified & directed. |
| 41 | Factory made single extruded WPC (Wood Polymer Composite) solid door/ window/ Ceosetory windows & other Frames/ Chowkhat of size 45 x 70 mm comprising of virgin PVC polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/ wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) fabricated with miter joints after applying PVC solvent cement and screwed with full body threaded star headed SS screws having minimum frame density of 750 kg/ cum, screw withdrawal strength of 2200 N (Face) & 1100 N (Edge), minimum compressive strength of 58 N/mm2, modules of elasticity 900 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/ moisture proof and fire retardant and fixed in position with MS hold fast/ lugs/SS dash fasteners of required dia and length complete as per direction of Engineer-in-Charge. (M.S. hold fast/ lugs or SS dash fasteners shall be paid for separately). |
| 42 | Providing and fixing factory made single extruded WPC (Wood Polymer Composite) solid decorative type flush door shutter of size 30mm thick comprising of virgin polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/ wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) having minimum density of 650 kg/cum and screw withdrawal strength of 1800 N (Face) & 900 N (Edge), minimum compressive strength 50 N/mm2 , modulus of elasticity 850 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/moisture proof and fire retardant. WPC to be laminated with PVC foil of minimum 14 microns thick of approved design pasted with hot melt adhesive on both faces of shutter and fixing with stainless steel butt hinges of required size with necessary full body threaded star headed counter sunk S.S screws, all as per direction of Engineer-in- Charge |
| 43 | 100 mm size butt hinges medium weight cold rolled stainless steel complete, all as specified and directed. |
| 44 | Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), removing and rubbish of the premisses, complete all as specified and directed. |
| 45 | Glazed coloured ceramic tiles in vertical surface 300mm x 450mm x 7mm thick , set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tile, over and including 10mm thick rendering in cement mortar 1:4 complete all as specified and directed. |
| 46 | Demolition of un-reinforced cement concrete in ground floors and pavings not exceeding 15 cm thickness. (Below or above ground level) complete all as specified and directed. |
| 47 | 75mm thick Plain cement concrete 1:3:6 type C-2 using 40mm graded aggregate as in sub base complete all as specified & directed. |
| 48 | Cutting chases in brick walls, pinning in, making good to facings where required and pointing in cement mortar (1:3) for concealed pipe etc and making good, cutting not exceeding 10cm girth complete all as specified & directed by Engineer-in-charge. |
| 49 | Taking up or down PVC/ GI tubing and connections 15mm bore from walls, floors etc complete all as specified and directed (cutting chases and making good shall be measured and paid separately). |
| 50 | Taking up or down PVC/ GI tubing and connections 20mm bore from walls, floors etc complete all as specified and directed (cutting chases and making good shall be measured and paid separately). |
| 51 | 20 mm (outer dia) CPVC pipes, SDR 11 and Plain CPVC SDR 11 fittings, fixed on walls/ceiling or laying in floors, complete all as specified and directed. |
| 52 | 20 mm bore Galvanized Steel tubes, medium grade including all fittings for flush pipes, water supply pipes etc., fixed to walls and ceilings or laid in floors complete all as specified and directed. |
| 53 | Brass elbow 20x15mm for CPVC pipe complete all as specified and directed. |
| 54 | Brass Tee 20mm dia for CPVC pipe complete all as specified and directed. |
| 55 | Male Brass Threaded Adaptor 20mm dia (MTA/ MBTA) ) for CPVC pipe complete all as specified and directed. |
| 56 | Female Brass Threaded Adaptor (FTA/ FBTA) 20mm dia for CPVC pipe complete all as specified and directed. |
| 57 | Bib taps brass, fancy type, long body with wall flange, chromium plated, cast copper alloy, screwed down for iron pipe or for brass ferrule, suitable for 15mm bore pipe, fixed in repair complete all as specified and directed. |
| 58 | Angular stop cock, fancy type, long body with wall flange cast copper alloy chromium plated, screwed down, screwed both and for iron pipe or for union, suitable for 15mm bore pipe, fixed as in repair complete all as specified and directed. |
| 59 | Stop cock, fancy type, cast copper alloy chromium plated, screwed down, screwed both and for iron pipe or for union, suitable for 15mm bore pipe, fixed as in repair complete all as specified and directed. |
| 60 | 15mm bore pillar tap, fancy type, cast copper alloy, with capstan heads, chromium plated, screwed down high pressure with or without lettered ‘Hot’ or ‘Cold’ with long screwed shanks and fly nuts, fancy type as in repair complete all as specified and directed. |
| 61 | Chromium plated, shower rose with or without swivel joints 125mm dia with arm and fixing to steel pipe 15mm bore, complete all as specified and directed |
| 62 | Looking mirror of size 600mmx450mm of selected quality mounted on PVC frame and back fixed to wall with screw and rawl plugs, fixed as in repairs,complete all as specified and directed. |
| 63 | Wash hand basin, vitreous china, flat back , white , of size 550X400mm, angle brackets waste coupling and waste pipe, fixed as in reapir complete all as specified and directed. |
| 64 | PVC valve less syphonic action type flushing cistern low level white with PVC in let ball valve, float and handle, 10 ltrs capacity and connection to pipes, set with concrete and making good to floor, fixed in repair complete all as specified & directed. |
| 65 | 15mm dia PVC connection with PTMT nut, of length 600mm, fixed as in repair complete all as specified and directed. |
| 66 | Towel rail 600mm long of PTMT fixed with and including chromium plated brass screws and wooden / plastic cleats (minimum weight 190gms), fixed as in repair complete all as specified and directed. |
| 67 | Nahani traps 75mm dia with grating including jointing to waste pipe with run led jointed and setting/fixed in cement concrete type B-1 1:2:4 fixed as in repair complete all as specified and directed. |
| 68 | PVC (SWR) gully trap 125/110 mm, setting and jointing with solvent cement fixed as in repair complete all as specified and directed. |
| 69 | Vitreous china squatting pan, “Orissa” pattern size 580mm x 440mm white, with integral foot rests (excluding flushing cistern and flush pipe) including connection to trap and flushing pipe, set with cement concrete, fixed as in repair, complete all as specified & directed. |
| 70 | Taking down eaves gutters and rainwater pipes (any size or pattern), including all fittings, heads, shoes, bends, swan-necks, etc., including cleaning or refixing or removal to Store complete all as specified and directed. |
| 71 | PVC (SWR) pipe, 110mm bore, single socketed in any length with rubber ring joints, having minimum density 6 Kg/cm2 laid in trenches or in floor, complete all as specified and directed. |
| 72 | PVC (SWR) pipe, 75mm bore, single socketed in any length with rubber ring joints, having minimum density 6 Kg/cm2 fixed to walls with MS clamps made out of flat iron including nuts bolts etc, complete all as specified and directed. |
| 73 | Supply and fixing PVC (SWR) bends any radius 110mm bore complete all as specified and directed. |
| 74 | 110mm bore PVC (SWR) junction single, (Single T/ Y) equal or unequal, with access door complete all as specified and directed. |
| 75 | 110mm bore PVC (SWR) vent cowl complete all as specified and directed. |
| 76 | Supply and fixing PVC (SWR) bends any radius 75mm bore complete all as specified and directed. |
| 77 | PVC (SWR) rain water pipe, 110mm bore, single socketed in any length with rubber ring joints, fixed to walls with MS clamps made out of flat iron of size 25mm x 3mm including nuts bolts etc, complete all as specified and directed. |
| 78 | Supply and fix 1000 litres capacity rotational moulded polyethylene water storage tanks (Cylindrical vertical with closed top) Double layered, screwable lid, hoisted and fixed in position, including tank nipple etc, including dismantling of existing water tank complete all as specified |
| 79 | 500 litres capacity rotational moulded polyethylene water storage tanks (Cylindrical vertical with closed top) double layered, white in colour, screwable lid, hoisted and fixed in position, including PTMT ball valve 20mm bore & PTMT tank nipple, etc, including dismantling of existing tank, complete all as specified and directed. |
| 80 | CP Brass wall mixer 15mm bore dia pipe for mixing hot & cold water screwed down for iron pipe and fixed, as in repair complete all as specified |
| 81 | Repair to RCC sunshades, chajjas, balconies, columns, bands, beams and similar RCC work at any position / height by dismantling loose / disintegrated portion including necessary scafolding and safety arrangements and fixing of reinforcement (cut to length, bent to shape required, including cranking, bending spirally including mild steel wire (annealed) not less than 0.9 mm dia. or securing with clips)/ chicken wire mesh wherever required and dubbing out with cement concrete 1:1.5:3, 15mm to 50mm thick, using 6 to 12mm graded stone aggregate to make up and finished the required shape including provision of necessary scaffolding and formwork up to four storey bldg if required and finished with 5mm thick rendering in cement mortar 1:4 finished even and fair without using extra cement complete all as specified and directed. |
| 82 | Hard drawn steel wire fabric n. Exc 4kg weight per square metre cut to lengths, bent to shape required and tying with and including mild steel wire (annealed) not less than 0.9mm in dia supplied and fixed in reinforcemnt complete all as specified and directed. |
| 83 | 16 to 18mm thick granite stone slabs(one piece), machine cut (of any type) work (table rubbed and polished) width and length as ordered, best quality machine cut and granite polished to be fixed on kitchen platform, window-cills, counter slab etc jointed with gray cement slurry and pointed in white cement mixed with marble dust (1:2) with admixture of pigment to match the shade of slab, screed bed 15mm thick in cement mortar 1:6 and rounding off/bull nosing exposed edges complete all as specified and directed. |
| 84 | Surface dressing n.exc 15cm deep in hard dense soil complete all as specified and directed |
| 85 | Excavation in trenches not exceeding 1.5m wide and not exceeding 1.5m in depth for foundation etc or for shaft, wells, cesspits, manholes, pier holes etc not exceeding 10 sqm on plan and getting out in soft and loose soil all as specified & directed by Engineer-in-Charge. |
| 86 | providing cement concrete type D2, 1:4:8 using 40 mm graded stone aggregate, as in foundations, filling and mass concrete and sub base etc., complete all as specified and as directed |
| 87 | Reinforced cement concrete (M-25, design mix) as in Foundations, including rafts, footings, foundation beams; plinth beams; bases for columns, etc.; basement slabs, under-reamed piles and mass concrete complete all as specified and directed (reinforcement shall be measured and paid for separately). |
| 88 | Reinforced cement concrete (M-25, design mix) as in columns, pillars etc complete all as specified and directed (reinforcement shall be measured and paid for separately). |
| 89 | Reinforced cement concrete (M-25, design mix) as in beams, cantilevers , bressumers,lintels over 1.5m span, all as specified and directed . (reinforcement shall be measured and paid for separately). |
| 90 | Reinforced cement concrete 1:1½:3 (nominal mix,type A-1, using 20mm graded crushed stone aggregate) as in chajjas, parapets, facia etc, all as specified and directed . |
| 91 | Reinforced cement concrete (M-25, design mix) as in slabs supported on walls, beams etc, shelves and the like complete all as specified and directed (reinforcement shall be measured and paid for separately). |
| 92 | Formwork to sides of concrete foundations, footings, bases of columns, raft and raft beams, sides and soffits (if any) of foundation and plinth beams; and similar work; vertical or to batter , all as specified and directed. |
| 93 | Form work to sides of pillars, columns and similar items (square, rectangular or polygonal) including edges rough finished surface of concrete flat complete all as specified and directed. |
| 94 | Form work to sides and soffits of floor or roof beams, beam haunchings, girders, bressummers, lintels, cantilevers, shelves including supports, overhangs, etc. also splays between floors and beams, etc. for roughly finished flat surfaces of concrete, all as specified. |
| 95 | Formwork to soffits of suspended slabs such as roof slabs, floor slabs, landings and similar work; not exceeding 200mm thick (Horizontal or sloping) curved/ flat, rough finished surfaces of concrete complete all as specified and directed. |
| 96 | Form work to edges of concrete, treads, break in floors, window cills, concrete railings, openings in concrete walls, floor and roofs n.exc 20cm wide and side of RCC / PCC bends in walls , horizontal or sloping and similar work exc 10cm but n.exc 20cm wide complete all as specified and directed. |
| 97 | TMT bars 10mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9 mm dia. or securing with clips complete all as specified and directed. |
| 98 | Mild steel TMT bars 6 to 8mm dia as in stirrups, spacers and binding , cut to length, bent to shape required including cranking, bending, spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips, all as specified. |
| 99 | Preparation of new surfaces and applying Two or more coats of 100% Premium acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives @ 1.43 litre/ 10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/ 10 sqm over new surfaces, complete all as specified and directed. |
| 100 | Preparation of old plastered surfaces and applying Two or more coats of 100% Premium acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives @ 1.43 litre/ 10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/ 10 sqm over new surfaces, complete all as specified and directed. |
| 101 | Sand filling (sand shallbe free from vegetation, pebbles, foreign materials) under floor including watering and consolidation in layers n.exc 25cm thick, complete all as specified & directed. |
| 102 | Hard core of broken stone or boulders of gauge exc. 63mm but n.exc 100mm, deposited, spread and leveled in layers n.exc. 15cm thick, watered and rammed to a true surface complete all as specified & directed. |
| 103 | Cement concrete 1:3:6, type C2 (40mm graded stone aggregate) for 100mm thick floor as in sub base complete all as specified & directed. |
| 104 | Returning filling in, including spreading, leveling, watering and well ramming in layers not exceeding 25 cm depth , complete all as specified and directed. |
| 105 | Steel windows with side hung shutters including projecting type hinges with steel handle, and steel peg stay, complete with glazing bars, dovetailed or welded including one coat of red oxide primer etc complete all as specified and directed. |
| 106 | Steel windows with side hung shutters including projecting type hinges with steel handle, and steel peg stay, complete without glazing bars, dovetailed or welded including one coat of red oxide primer etc complete all as specified and directed. |
| 107 | Framed work such as grills, gratings etc., with ends of bars shouldered and/or riveted, or forget into spikes; for ornamental and intricate design, framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; framework of water tanks and similar work conforming to Fe 410-0 or Fe 310-0, all as specified and directed. |
| 108 | Sheet glass 4mm thick, ordinary quality and glazing with oil putty in square, area not exc 0.5 sq. mtr in each pane,complete all as specified and directed. |
| 109 | Removal of excavated material exceeding 200 metre but n exc 500metre and depositing where directed at a level not exceeding 1.5 metre above the starting point , filling in including spreading, leveleing, watering and well ramming in layers not exc 25cm complete all as specified and directed. |
| 110 | Preparing surfaces of steel and iron work, new or old, of any description and girth, not otherwise described, and treated with tar or coal tar black paint treating small articles such as stop, covers, gully gratings, holdfasts, ends of posts, backs of chowkats, etc, area n exc 0.1 sq. m each complete all as specified and directed. |
| 111 | Material and labour cement concrete type B-0, 1:2:4 using (12.5 mm graded crushed stone aggregate) as in roof kerbs or mud stops, rounded or chamfered on edges in lintels upto 1.5m clear span, cills, steps, seismic and other similar bands, plinth courses, parapets and railings upto 60 cm in height, copings, bed plates, water troughs and the like including weathering, slightly rounded or chamfered angles and throating, including the use of forms or moulds with plain faces complete all as specified and directed. (Cement concrete item shall be reinforced, where ordered. Reinforcement shall be measured and paid separately). |
| 112 | Plain cement concrete 1:3:6 type B-1 using 20mm graded crushed stone aggregate as in foundation, filling and mass concrete complete all as specified & directed. |
| 113 | Cleaning top surface, terracing or cement concrete, including flashings and junction of parapets, etc., and adjoining vertical surfaces and applying bituminous primer @ 0.40 litres per square meter including APP based polymeric membrane minimum weighing 3 kg/sqm and minimum 3 mm thick reinforced with polyester non woven fabric (weight not less than 150 gms/sqm) laid on primed surface by torch application & membrane complete all over and including 10mm thick rendering in CM 1 :4 mixed with water proffing compound complete all as specified and directed. |
| 114 | Providing and laying 60mm thick factory made chamfered edge cement concrete paver block of M-35 grade with approved colour, design & pattern as in footpath, parks, lawns, drive ways or light trafiic parking etc., of required strength, thickness & size/shape, blocks made by table vibratory method using PU mould, laid in required colour & pattern over and including 50mm thick compacted bed of fine sand, compacting and proper embedding/ laying of inter locking paver blocks as per required size and pattern, finishing and sweeping extra sand incl dismantling of existing paver block any shape and size laid dryed of any thickness and pattern.complete all as specified and directed. |
| 115 | Demolition of 25mm thick RCC louvers / jalli in shaft & other similar place and removal of debrisupto a distance of 2 Km from starting point, including all necessary scaffolding and safety arrangement complete all as specified and directed. |
| 116 | Demolition of plain cement concrete (reinforcement cut as required to facilitate demolition) of any description and in any position complete all as specified and directed. |
| 117 | Providing precast cement concrete 40mm thick RCC Jallies in (1:2:4) type B-0 using 12.5mm graded crushed stone aggregate, (measured solid), including all mouldings but excluding frame set in cement mortar 1:4 Complete all as specified and directed. |
| 118 | Form work to chullah hoods, chajjas and similar items including edges / sides and soffits of lintels etc rough finished surface of concrete flat complete all as specified and directed. |
| 119 | Dubbing out average 20mm thick on irregular faces of walls, exposed reinforced surfaces, in Cement and Sand mortar 1:4 complete all as specified and directed |
| 120 | 25mm thick PCC 1:2:4 type B-0 (using 12.5mm graded crushed stone aggregate) as in sub base finished fair and even without using extra cement, complete all as specified and directed. |
| 121 | Kota stone slab 20-25mm thick in riser of steps, skirting, dado and pillars laid over and including 10mm thick rendering in 1:4, laid and jointed with grey cement slurry mixed with pigment to match the shade of slab including rubbing and polishing complete all as specified and directed. |
| 122 | Kota Stone Slab flooring, 20-25mm thick, best quality over and including cement screed bed 15mm thick in cement mortar 1:6, laid and jointed with grey cement slurry and pointed with grey cement mixed with pigment to match the shade of the slab including cutting, rubbing, grinding and polishing complete all as specified and directed. |
| 123 | 25mm dia stainless steel curtain rod including fixing fancy types brackets, stops, rollers etc., as in repairs complete all as specified and directed. |
| 124 | Demolition of mud phuska as in roof of any thickness incl plastering and leeping etc (whether full thickness removed or only a part thereof), removal of debris complete all as specified & directed. |
| 125 | 50mm thick (average thickness) PCC 1:2:4, type B-0 (using 12.5mm graded stone aggregates) as in levelling course, sub base and roof padding, including mixed with WPC complete all as specified and directed. |
| 126 | Prepration of surfaces of any description, over 10cm in width or girth, not otherwise described and applying two coats of Bituminous Aluminum paint @ 100gm/sqm on top of membrane complete all as specified & directed |
| 127 | Heat Resistant Terrace Tiles (300 mm x 300 mm x 20 mm) with SRI (solar refractive index) > 78, solar reflection > 0.70 and initial emittance > 0.75 on waterproof and sloped surface of terrace, laid on 20 mm thick cement sand mortar in the ratio of 1:4 (1 cement : 4 coarse sand) and grouting the joints with mix of white cement & marble powder in ratio of 1:1, including rubbing and polishing of the surface upto 3 cuts complete, including providing skirting upto 150 mm height along the parapet walls in the same manner complete all as specified and directed. |
| 128 | 15mm Tubes, medium grade galvanised, with all fitting and fixed complete to walls and ceilings or laid in floors in floors complete all as specified and directed. |
| 129 | Fixing only 20mm Tubes, medium grade galvanised, with all fitting and fixed complete to walls and ceilings or laid in floors in floors complete all as specified and directed. |
| 130 | Supply and fix 110mm bore PVC (SWR) bends any radius with access door etc complete all as specified and directed |
| 131 | Coloured non skid porcelain tiles exterior grade 600x600x10mm thick heavy duty (Endura from Johnson or equivalent) as in floor, set and jointed in neat slurry and pointed in coloured cement to match the colour of tiles over and including screed bed or bedding layer of 15mm thick in cement mortar 1:6, complete all as specified and directed |
| 132 | Solid PVC board 20mm thick, with 2mm thick prelam PVC sheet on the front face & 2mm relam PVC sheet on back with particle board core fixing in frame at site to cup board shutter, shelves and kitchen cabinet complete all as specified and directed. |
| 133 | Continuous piano hinges having flap width 40mm when open mild steel,bright finish or electrogalvanised complete all as specified and directed by Engineer-in-charge. |
| 134 | 100mm hasp and staple,aluminium anodised, including bolt to hinge plate and fixed with screws, complete all as specified and directed. |
| 135 | PVC body magnetic shutter catcher for kitchen cup boards, fixed with standard steel screws, complete all as specified and directed. |
| 136 | Stainless steel wire cloth 0.36mm nominal dia of wire and average width of aperture 1.40mm including fixed with tinned tacks / stainless steel wire staples, complete all as specified & directed. |
| 137 | Preparation of new plastered or un-plastered surfaces of wall and applying two coats of oil bound distemper over a coat of chalk whitening preparatory to distempering and priming complete all as specified and directed. |
| 138 | Disconnecting existing tanks exc 500 litres, setting aside (or lowering if required) for repairs, cleaning, etc. and hoisting if required reconnecting and re-fixing in position after Cleaning repairing etc. complete all as specified & directed by Engineer-in-charge. |
| 139 | Dismantling precast concrete interlocking paver block any shape and size laid dried of any thickness and pattern incl sand bedding layer ,complete all as specified and directed. |
| 140 | Taking down carefully aluminum/copper point wiring on & including hard wood battens, surface conduit and board/blocks etc or through conduits for light , socket or power point ,fan point complete incl fitting such as switches ,sockets, ceiling rose , holder socket, light fitting, regulators and making good disturbed surfaces of wall, floor , ceiling etc and removing materials (other than those for which credit has been given by the contractor) to the MES stores yard for keeping in safe custody complete |
| 141 | Point wiring with approved colour code multi stranded copper conductor, PVC insulated and unsheathed FRLSH cable of size 1.5 Sqmm ,1100 volts grade, two run of single core cable for phase & neutral and one run of single core multi stranded copper conductor, PVC insulated and unsheathed FRLSH cable of size 1.5 Sqmm ,1100 volts grade for earth continuity conductor to common earth and connected to earth dolly in and including new concealed PVC conduit terminated on and including new modular sunken box and suitable size of frame, cover for mounting switch, socket and regulator fixed on surface flush with wall , comprising of One light /bell/buzzer point controlled by one switch or one fan point controlled by one switch &fan regulator, complete all as specified and directed. Note : Unit rate is inclusive of making good the disturbed surfaces by provding by wall putty/POP after mason work and finshing to match the original and nothing extra shall be paid on this account. Note :Unit rate is inclusive of cutting chases in wall /foor/PCC and making good the disturbed surfaces to match the original and nothing extra shall be paid on this account. |
| 142 | All as per serial item 141 herein before but for socket outlet 3 pin 5 Amps on same board complete all as specified and directed |
| 143 | All as per serial item 141 herein before but for socket outlet 3 pin 6 Amps on independent board complete all as specified and directed |
| 144 | All as per serial item 141 herein before but One socket outlet three pin ,6/16 Amp, independent board, with 2.5 Sqmm (nominal area ) FRLSH cable & 2.5 Sqmm (nominal area ) cable as earth continuity conductor |
| 145 | Switch modular type (ISI marked), single pole, one way 6 Amps, one module (ISI marked), complete all as specified & directed. |
| 146 | Switch modular type (ISI marked), single pole, one way 16 Amps, one module (ISI marked), complete all as specified & directed. |
| 147 | Socket shutters outlet 2/3 pin 6 Amp modular type multi purpose two module (ISI marked), complete all as specified & directed. |
| 148 | Socket shutters outlet 2 in 1 pin 6/16 Amp modular type multi purpose combined 2 module (ISI marked), complete all as specified & directed. |
| 149 | Modular switch type stepped fan regulator, single pole, 230 volt two module complete all as specified and directed. |
| 150 | Ceiling rose, PVC or polycarbonate of size 65mmx50mm three terminals (ISI marked) all as specified and directed by Engineer-in-charge. |
| 151 | Lamp holder, PVC/Polycarbonate type with back plate modular type fixed on wall suitable for batten fitting ,complete all as specified and directed. |
| 152 | LED Bulb 12 watt self ballasted Retrofit type lamp with PBT body shell and DC diffuser CCT 6500 K complete all as specified and directed. |
| 153 | LED lights fitting, 4 feet, 1x 20W, inverter rechargeable, inbuilt lithium ion battery with charging time 8 to 10 hrs & back upt time minimum 8 hrs, 220V, AC decorative box type with driver, holder including LED tube light connecting up with three core flexible copper conductor cable of suitable size from ceiling rose fixed as in repair complete all as specified and directed. |
| 154 | LED lights fitting, 4 feet, 1x 20W, inverter rechargeable, inbuilt lithium ion battery with charging time 8 to 10 hrs & back upt time minimum 8 hrs, 220V, AC decorative box type with driver, holder including LED tube light connecting up with three core flexible copper conductor cable of suitable size from ceiling rose complete all as specified and directed. |
| 155 | LED Lights fitting 1 x 9/10 Watt, 2 feet ,220V AC decorative type including fitting fixed on wall/ceiling and connecting up complete with flexible cable white of suitable size and making necessary connection fixed as in repair complete all as specified and directed. |
| 156 | LED light fitting 1x9W/1X10W bulkhead luminaires including LED light driver holder connecting up with three core flexible copper conductor cable of suitable size, complete all as specified and directed. |
| 157 | LED light fitting 1x9W/1X10W bulkhead luminaires including LED light driver holder connecting up with three core flexible copper conductor cable of suitable size, complete all as specified and directed. |
| 158 | Taking down carefully old copper or aluminium sub main wiring of any Nos of wiring and size with earth wire on wooden batten/ surface conduit/ casing- capping complete with its all accessories and making good disturbed surfaces of wall , floors etc complete all as specified and directed. |
| 159 | Sub main wiring with two single core FRLSH PVC insulated and unsheathed cable with copper conductor of size 4 Sqmm (nominal area), 1100 Volt grade(with approved colour coding as per IS) with and including continuous earth wire of size 4 Sqmm PVC insulated and unsheathed FRLSH multi stranded copper conductor 1100 volts grade , and connected to main board drawing through PVC concealed conduit 25mm size(minimum size), cutting chases in walls for PVC concealed conduit and making good the disturbed surfaces by providing by wall putty/POP after mason work and finshing to match the original surfaces and nothing extra shall be paid on this account all as specified and directed. |
| 160 | Sub main wiring with two single core FRLSH PVC insulated and unsheathed cable with copper conductor of size 6 Sqmm (nominal area), 1100 Volt grade(with approved colour coding as per IS) with and including continuous earth wire of size 6 Sqmm PVC insulated and unsheathed FRLSH multi stranded copper conductor 1100 volts grade , and connected to main board drawing through PVC concealed conduit 25mm size(minimum size), cutting chases in walls for PVC concealed conduit and making good the disturbed surfaces by providing by wall putty/POP after mason work and finshing to match the original surfaces and nothing extra shall be paid on this account all as specified and directed. NOTE FOR SERIAL ITEM NO 158 & 159: (i) Two runs of cable, one run of earth wire shall be considered as one running metre(ii) Cutting chases will be measured and paid separtely(iii) colour code shall be Red for phase, Black for neutral and green for earth |
| 161 | Cutting chases in brick walls, pinning in, making good to facings where required and pointing in cement mortar (1:3) to ends or edges of landings, steps, cills, sunshades, shelves, lintels, etc and cutting chases for concealed water tubing or concealed conduit wiring etc and making good, cutting not exceeding 10cm girth Complete all as specified and directed . |
| 162 | Disconnecting the power supply and taking down carefully by unscrewing from boards fittings and fixtures such as DBs, Junction Box, Panels of any size complete with all MCCB's ,MCB's etc and removing from site, Complete all as specified and directed . |
| 163 | MCB DB, IP 43 protection, powder coated double door with locking arrangement suitable for surface and flush mounting, (2 + 10 way) 12 way SPN with 200 Amps busbar 240V completed all as specified and directed. |
| 164 | MCB DB, IP 43 protection, powder coated double door with locking arrangement suitable for surface and flush mounting, (2 + 6 way) 8 way SPN with 200 Amps busbar 240V completed all as specified and directed. |
| 165 | MCB DB, IP 43 protection, powder coated double door with locking arrangement suitable for surface and flush mounting, 4 way SPN with 200 Amps busbar 240V completed all as specified and directed. |
| 166 | MCB, SPN , 240 volt, 32Amps, 10 KA , 'C' series including connection with suitable size aluminium / copper lugs complete all as specified and directed |
| 167 | MCB ,SP , 240 volt, 6Amps to 32Amps, 10 KA , 'C' series including connection with suitable size aluminium / copper lugs complete all as specified and directed |
| 168 | Single pole and neutral sheet metal enclosure with a two pin and earth plug and socket complete with one number single pole MCB 20 Amps , 240 Volts for AC/Geyser point complete all as specified and as directed. |
| 169 | LED building security light fitting 1 x 35 Watt new generation energy saving and environmental friendly long life LED street light made up of pressure diecast aluminium housing with high power LED as lighting source and lens embedded PC cover having top opening seperate driver compartment with IP65 protection incl mounting bracket of suitable size and connection fixed as in repair complete all as specified and directed. |
| 170 | LED building security light fitting 1 x 35 Watt new generation energy saving and environmental friendly long life LED street light made up of pressure diecast aluminium housing with high power LED as lighting source and lens embedded PC cover having top opening seperate driver compartment with IP65 protection incl mounting bracket of suitable size and connection complete all as specified and directed. |
| 171 | Taking down carefully old unserviceable ceiling fan/wall fan/exhaust fan complete removing its blade and deposit to the MES store yard complete all as specified and directed. |
| 172 | Ceiling fans complete with blades, down rods, electronic regulator and accessories, 230 V, 1200 mm sweep. Min air delivery 210 CFM with service value 6.00 BEE. Five star rated with brushless direct current motor (BLDC) and provision of flexible copper cable 3 core from ceiling rose to fan complete all as specified and directed. |
| 173 | Exhaust fan made of sturdy Engineering plastic complete with louvers shutter, voltage 230V, 50 Hz, RPM 1200, Copper winding of sweep 300mm complete all as specified and directed. |
| 174 | Exhaust fan, steel body AC single Phase. 230V of size 300mm sweep with, blades, and frame and louvers and provision of flexible copper cable 3 core from ceiling rose to exhaust fan complete all as specified and directed. |
| 175 | Cutting openings, through brick walls in round shape , for 300mm dia exhaust fan and making good in cement mortar 1:3 or cement concrete 1:2:4 type B-l as required including finishing and matching the disturbed surface and removing surplus unserviceable bricks, hard-core, etc..from site and rubbish complete all as specified & directed by Engineer-in-charge. |
| 176 | XLPE insulated, armoured heavy duty electric cable with aluminium conductor, 1100 volts grade, cross-sectional area 16 sqmm, 2core, laid in trenches , sleeving through pipes of fixed on poles & wall or laid under floors inlcuding jointing with suitable size of alumunium lugs as specified and directed. |
| 177 | 32mm outer dia, double walled corrugated (DWC) HDPE duct pipe conforming to IS 14930 Part-II with anti rodent and non flame propogating properties of approved colour with fittings for cable protection from approval make complete , all as specified and directed |
| 178 | Removal of excavated material to distance exceeding 50 metre nut not exceeding 1.50 metre and depositing where directed at a level not exceeding 1.5 metre above the starting point , complete all as specified and directed. |
| 179 | Earthing complete with galvanized steel earth plate electrode 600mm x 600mm x 6mm buried directly in ground vertically to a depth not less than 2.25 meter below normal ground level (with top edge of earth plate not less than 1.5 meter below ground level) connected to galvanized iron earth lead wire 4mm dia, (main earthing lead ) by means of galvanized bolts, nuts and washers all as shown in electrical plate no 5 of MES Schedule Part-I (1991) with connected to earth test point & to main switch board with & including adequate quantity of charcoal dust and common salt alround earth plate & 15 mm dia GI pipe light grade for earth lead protection pipe for suitable length and GI pipe 20 mm dia light grade for watering pipe with funnel & wire mesh including necessary earth work and PCC (1: 3 : 6) type C-1 for earth pit and 40 mm thick pre-cast RCC cover in 1 : 2 : 4 type B1 with 3 Nos 8 mm dia TMT bars both ways complete all as specified & directed. |
| 180 | Earthing complete with galvanized steel earth plate electrode 600mm x 600mm x 6mm buried directly in ground vertically to a depth not less than 2.25 meter below normal ground level (with top edge of earth plate not less than 1.5 meter below ground level) connected to galvanized iron earth lead wire 4mm dia, (main earthing lead ) by means of galvanized bolts, nuts and washers all as shown in electrical plate no 5 of MES Schedule Part-I (1991) with connected to earth test point & to main switch board with & including adequate quantity of charcoal dust and common salt alround earth plate & 15 mm dia GI pipe light grade for earth lead protection pipe for suitable length and GI pipe 20 mm dia light grade for watering pipe with funnel & wire mesh including necessary earth work and PCC (1: 3 : 6) type C-1 for earth pit and 40 mm thick pre-cast RCC cover in 1 : 2 : 4 type B1 with 3 Nos 8 mm dia TMT bars both ways, taking out existing earthing complete all as specified & directed. Please Enable Macros to View BoQ information |
AI Tender Summary
Tender Timeline
Jul 08, 2026
11:30 IST
Tender Published
Tender notice published.
CompletedJul 29, 2026
17:00 IST
Bid Submission Deadline
Online submission via eProcurement portal.
Upcoming · 16 daysJul 31, 2026
Bid Opening Date
Technical bids will be opened and evaluated.
Upcoming · 18 daysTender Documents
Download All (ZIP) ↓
Disclaimer
We takes all possible care for accurate & authentic tender information. However users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender