Tender For Special Repair Of Bldg No T-280 At Certain Unit In Hasimara Mil Stn Under Ge (S) Binanguri
Tender Value
22.33 Lakhs
Estimated cost
Bid Submission
30 Jul 2026
17 days left
EMD
44700
Bank guarantee accepted
Document Fee
500
Non-refundable
Tender Type
Online
Tender Overview
Organization
Tender ID
Competition Type
NCB
Bidding Type
Tender
Location / State
Jalpaiguri → West Bengal
EMD Exemption
Available
Quantity
Not Available
Website
Contact Person
Address
Project Description
Tender for Special Repair Of Bldg No T-280 At Certain Unit In Hasimara Mil Stn Under Ge (S) Binanguri
BOQ
| Sl. No. | Item Description |
| 1 | Dismantling of plain or corrugated steel sheeting, any gauge, thickness, including Nainital or similar pattern roof coveringscomplete all as specified. |
| 2 | Dismantling timber scantlings 40 sqcm and over in section as in framed work in any positioncomplete all as specified.. |
| 3 | Dismantling of wall and ceiling Boards(Fiber,pulp, Insulation etc) or insulation Board/slab/blankets any Thinkness including cover filletscomplete all as specified. |
| 4 | Demolition of reed, lathing, single or double, including battens and plaster or chicken wire lathing. |
| 5 | Demolition of brick work or stone/boulder masonry built in cement mortar including all quoins, arches, pillars etccomplete all as specified. |
| 6 | Taking down chowkats or frames not exc 1.5 Sqm each with shutters ( with out taking off shutters from the frames)complete all as specified. |
| 7 | Taking down chowkats or frames exc 1.5 sqm but not exc 4.0 Sqm each with shutters ( with out taking off shutters from the frames)complete all as specified. |
| 8 | Demolition of cement concrete of any position and description complete all as specified. |
| 9 | M&L for PCC 1:4:8 type D2 using 40mm graded stone aggregate as in foundation filling and mass concretecomplete all as specified. |
| 10 | M&L fly ash Brick work using modular size bricks with sub class 'B' bricks curved on plan with mean radius not exc 6m with bricks roughly cut to radius or bricks with wedge shaped joints built in cement mortar 1:6complete all as specified. |
| 11 | M&L for RCC (nominal mix) 1:1.50:3. type B1 using 20 mm graded stone aggregate as in foundations, including rafts, footings, foundation beams, plinth beams, bases for columns, etc, basement slabs, under reamed piles and mass concretecomplete all as specified. Note - Reinforcement and form work shall be measured and paid separately. |
| 12 | M&L for RCC (nominal mix) 1:2:4 type B1 using 20 mm graded stone aggregate as in beam, cantilevers, bressummers, lintels over 1.5 m span and similar workcomplete all as specified.Note - Reinforcement and form work shall be measured and paid separately. |
| 13 | M&L for RCC nominal mix type A1,1:1.5:3 using 20mm gradded aggregate Slabs supported on walls, beams and columns in floors, shelves, platform, lintel, deck slabs and the like. |
| 14 | Form work to sides and soffits of floor or roof beam, beam hauchings, girders, bressummers, lintels, cantilevers, shelves, for flat rough finished concrete surfacescomplete all as specified. |
| 15 | Form work to sides of concrete foundation ,footings, bases of columns, raft and raft beams sides and soffits (if any )of foundation and plinth beams for flat rough finished concrete surfacecomplete all as specified. |
| 16 | M&L for RCC (nominal mix) 1:2:4 type B1 using 20 mm graded stone aggregate as in chajjas and similar workcomplete all as specified.Note - Reinforcement and form work shall be measured and paid separately. |
| 17 | Form work to chullah hood, chajjas, troughs and similar items including edges etc for rough finished flat concrete surfacecomplete all as specified. |
| 18 | Mild Steel TMT bar 10mm dia and over cut to length bent to shape required including cranking, bending spirally for hoping for columns hooking ends and binding with & including Mild Steel wire (annealed) not less than 0.9mm dia or securing with clipscomplete all as specified. |
| 19 | Mild Steel TMT bar 6 to 8 mm dia cut to length bent to shape required including cranking, bending spirally for hoping for columns hooking ends and binding with & including Mild Steel wire (annealed) not less than 0.9mm dia or securing with clipscomplete all as specified. |
| 20 | Mild Steel TMT bar 5mm dia and over upto and including 10mm dia as in stirrups, spacers & binders cut to length bent to shape required including cranking, bending spirally for hoping for columns hooking ends and binding with & including Mild Steel wire (annealed) not less than 0.9mm dia or securing with clipscomplete all as specified. |
| 21 | M&L for 40 mm thick in Cement concrete 1:2:4, type B-0 Damp proof course to horizontal or vertical surfaces including necessary formwork and mixed with water proofing compound 0.25Ltr/ Sqm or as per manufacturer's instructionscomplete all as specified. (Note: Water proofing compound shall be measured and paid seperately under relevant item of schedule 'A'). |
| 22 | M&L for 20 mm thick plaster of cement mortar (1:4) rendering on fair faces of brick work in two layers (10mm & 10mm) mixed with water proofing compound in top layer 200 ml per beg of cement or as per manufacturer's instructions finishing the surface fair and even without using extra cement complete all as specified and as directed. (Note: Water proofing compound shall be measured and paid seperately under relevant item of schedule 'A'). |
| 23 | Supply only Liquid water proofing compound all as specified. |
| 24 | M&L 15mm thick rendering in cement mortar 1:6 on other than fair face of brick work or concrete surface finished fair and even (without using extra cement)complete all as specified. |
| 25 | M&L for preparation of newly plastered surfaces of walls and applying two coats of oil bound distemper over a coat of primer after applying 2 coats of cement based wall putty 1 mm each to wall surfacecomplete all as specified. |
| 26 | M & L for preparing new Plastered surfaces of walls and applying two coat of cement base paint on surface of wal all as specified. |
| 27 | M & L for preparing new Plastered surfaces of walls and finishing the walls with Acrylic smooth exterior paint of required shade : New work (Two or more coats applied @1.67 Ltr/10 Sqm over and including priming coat of exterior primer applied @ 2.20 Kg/ 10 sqm). Make of Weather proof exterior acrylic emulsion and primer : Asian Apex Ultima/Berger weather coat long life 10 all as specified. |
| 28 | S & F Structural steel work in Roof trusses (framed), trussed, purlins, crane gantries, rails and fastenings and heavy bracket framing (Beam, tee, angle, channel or flat sections) including distance pieces, cleats etc. of Fe 410-W (Gde -E-250 quality- A) Add to any of the foregoing items if structural steel is painted one shop coat of zincchromate primer paint (including preparation of surface) at Contractor’s workshop before fabrication all as specified and directed. |
| 29 | S & F MS Plates (plain or chequered) channels, square cut or notched (ordinary and counter sunk) forming holes, without any attachment confirming to Fe-410-W (Gde E-250 quality B) with riveted, bolted or welded attachment complete all as specified and as directed by Engineer-in-charge. |
| 30 | S&F Mild steel screw bolts (machine made) with hexagonal / square heads at one end & screwed the other/ screwed both ends, each screwed end to be fitted with washers & one hexagonal or square nut, length of bolt exc 22.5cm & n exc 30cm long dia of shank 16 to 20 mm |
| 31 | M&L of two coat of synthetic enamel paint over one coat of red oxide on new steel surfaces of any description over 10cm in width or girth incl preparation of surfaces complete all as specified and as directed. |
| 32 | S & F pre painted galvalume aluminium zinc coating GI based corrugated steel sheet 0.50 mm thick of any colour having tensile strength 550 Mpa as in roof covering/ cladding/ eaves board fixed with selp tapping screwcomplete all as specified. |
| 33 | S & F pre painted galvalume aluminium zinc coating GI based plain steel sheet 0.50 mm thick of any colour having tensile strength 550 Mpa as in roof covering/cladding/eaves board fixed with selp tapping screwcomplete all as specified. |
| 34 | S&F Anodised aluminium snap grid frame work for false ceiling Size of grid 605 x 605mm all as specified. |
| 35 | S&F Hangers 6 mm dia. G.I. (upto 1200mm length) adjusting level fixed to roof slabs by means of ceilling cleats made out of G.I. flat 40 x 3 mm size 60mm long and expansion hold fasteners 12.5mm dia. 40mm long complete all as specified all as specified. |
| 36 | M&L for Non asbestos fibre cement building boards fixed or laid/ inserted totimber/GI/Aluminium framework with screws ,4mm thick designer board (610mm x 610mm ) size complete all as specified and as directed . |
| 37 | M & L for hardcore guage of broken stone or boulders of exc 63mm but n exc. 100 mm, deposited, spread and levelled in layers n exc. 15 cm thick, watered and rolled/rammed to a true surface. |
| 38 | Demolition of un-reinforced cement concrete in ground floors and pavings not exceeding 15 cm thickness (below or above ground level) as directed. |
| 39 | M&L for PCC 1:2:4 type B-1 using 20 mm graded stone aggregate as in floor finishes 25 mm thick finished even and smooth without using extra cementcomplete all as specified. |
| 40 | M&L for 100 mm thick Cement concrete 1:4:8 type D-2 using 40 mm graded stone aggregate as in sub basecomplete all as specified. |
| 41 | M&L for Machine cut kota stone slab flooring mirror finished 20-25 mm thick (each slab not less than 0.25 sqm) over cement screed base laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing and 15 mm thick screed bed or bedding layer in CM 1:4 surface finished fair and even for laying floor finishescomplete all as specified. |
| 42 | M&L for Machine cut kota stone in riser of steps, skirting, dado and pillar mirror finished 20-25 mm thick over cement base rendering laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing and including rendering 10 mm thick in cement mortor 1:4complete all as specified. complete all as specified. Please Enable Macros to View BoQ information |
| 43 | M&L for Machine cut kota stone in riser of steps, skirting, dado and pillar mirror finished 20-25 mm thick over cement base rendering laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing and including rendering 10 mm thick in cement mortor 1:4complete all as specified. complete all as specified. Please Enable Macros to View BoQ information |
AI Tender Summary
Tender Timeline
Jul 09, 2026
11:30 IST
Tender Published
Tender notice published.
CompletedJul 30, 2026
17:00 IST
Bid Submission Deadline
Online submission via eProcurement portal.
Upcoming · 17 daysAug 03, 2026
Bid Opening Date
Technical bids will be opened and evaluated.
Upcoming · 21 daysTender Documents
Download All (ZIP) ↓
Disclaimer
We takes all possible care for accurate & authentic tender information. However users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender