Tender For Renovation Of Khanna Inspection House Under The Control Of Irrigation Division Mahoba In District Mahoba. (Lot-02)
Tender Value
1.05 Crore
Estimated cost
Bid Submission
16 Jul 2026
2 days left
EMD
2.11 Lakhs
Bank guarantee accepted
Document Fee
2354
Non-refundable
Tender Type
Online
Tender Overview
Organization
Tender ID
Competition Type
NCB
Bidding Type
Tender
Location / State
Mahoba → Uttar Pradesh
EMD Exemption
Not Available
Quantity
Not Available
Website
Contact Person
Address
Project Description
Tender for Renovation Of Khanna Inspection House Under The Control Of Irrigation Division Mahoba In District Mahoba. (Lot-02)
BOQ
| Sl. No. | Item Description |
| 1 | Jungle clearence cutting heavy under growth and bushes upto 7.50 cm dia. Including removal. |
| 2 | Dismentling of existing slab including all cost material labour T&P etc. complete as per direction of Engineer-in-charge. |
| 3 | Dismentling of Masonary Brick work icluding all cost material labour T&P etc. complete as per direction of Engineer-in-charge. |
| 4 | Steel rainforcement including all cost material labour T&P etc. complete as per direction of Engineer-in-charge. |
| 5 | Centering & Shuttering for R.C.C. work including all cost material labour T&P etc. complete. |
| 6 | R.C.R. 1:4 including all cost material labour T&P etc. complete. |
| 7 | C.C. 1:3:6 Cement sand & mortar including all cost material labour T&P etc. complete. |
| 8 | C.C. 1:2:4 including all cost material labour T&P etc. complete as per direction of Engineer-in-charge. |
| 9 | C.C. 1:1.5:3 in Wearing coat on top of slab including all cost material labour T&P etc. complete as per direction of Engineer-in-charge. |
| 10 | Brick work class 150 with (1:4) cement sand mortar including all cost material labour T&P etc. complete as per direction of Engineer-in-charge. |
| 11 | Plaster 1:4 including all cost of labpur T&P etc. complete |
| 12 | Providing and laying Vitrified tiles in floor in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS:15622, of approved brand & manufacturer, in all colours and shade, laid on 20 mm thick cement mortar 1:4 (1 cement: 4 coarse sand) jointing with grey cement slurry @3.3 kg/sqm including grouting the joints with white cement and matching pigments etc. The tiles must be cut with the zero chipping diamond cutter only . Laying of tiles will be done with the notch trowel, plier, wedge, clips of required thickness, leveling system and rubber mallet for placing the tiles gently and easily. ouble charge vitrified tile polished finish of size. Size of Tile 600x600 mm |
| 13 | Providing and fixing 18 mm thick gang saw cut, mirror polished, premoulded and prepolished, machine cut for kitchen platforms, vanity counters, window sills, facias and similar locations of required size, approved shade, colour and texture laid over 20 mm thick base cement mortar 1:4 (1 cement: 4 coarse sand), joints treated with white cement, mixed with matching pigment, epoxy touch ups, including rubbing, curing, moulding and polishing of edges to give high gloss finish etc. complete at all levels. Granite stone slab of colour black, Cherry/Ruby red. Area of slab over 0.50 sqm |
| 14 | Providing edge maulding to 18mm thick granite/Marval stone including machine polishing ot edge to give high gloss finish etc. complete as per design approved by Engineer-in-charge. |
| 15 | Earth work by Power Transported Earth With a Lead beyond 200m and upto 1.0 km including excavation, loading, unloading, manual compation, dressing and all lift complete excluding royality and excluding cost of earth. |
| 16 | Dismentling Door, Windows, including choukhat with hol fash and Including stacking of dismentling as per direction of Engineer in charge. |
| 17 | Providing 40 x 5 mm flat iron holdfast 400 mm long including fixing to frame with 10 mm diameter bolts, nuts and wooden plugs and embedding in cement concrete block 300 x 100 x 150 mm 1:3:6 mix (1 cement : 3 coarse sand : 6 graded stone aggregate 20 mm nominal size). |
| 18 | Providing and laying damp-proof course 40 mm thick with cement concrete 1:2:4 (1 cement : 2 coarse sand (zone-III) derived from natural sources : 4 graded stone aggregate 12.5 mm nominal size derived from natural sources) and providing/ mixing water proofing material in cement concrete work in doses by weight of cement as per manufacturer's specification. |
| 19 | Providing and fixing Panelled or pannelled and glazed shutters for doors, windows and clerestory windows, fixing with butt hinges of required size with necessary serews, excluding panelling which will be paid for separately, all complete as per direction of Engineer-in-Charge (Note: butt hings and necessary screws shall be paid separately |
| 20 | Providing Wood work in fromes of doors, windows, clerestory windows and other frames, wrought framed and fixed in position with hold fast lugs or with dash fasteners of requrired din & length (Hold fast lugs or dash fastener shall be paid for separately) 9.1.2 sal wood cum 106720.85 |
| 21 | Providing and fixing wire gauge shutters using galvanized M.S. wire gauge of average width of aperture 1.4 mm in both directions with wire of dia 0.63mm for doors, windows and clerestory windows with hings and necessary screws: 9.27.1 35mm thick shutters 9.27.1.1 with ISI marked M.S. pressed butt hinges bright finished of required size 9.27.1.1.1 second class teak wood |
| 22 | Providing and fixing chromium plated brass curtain rod having wall thickness of 1.25mm with two chromium plated brass brackets fixied with C.P. Brass screws and PVC sleeves etc. wherever necessary Complete 9.46.3.25 mm dia meter 482.30 |
| 23 | Providing and fixing ISI Marked oxidised M.S. sliding door bolts with nuts and screws etc. complete. |
| 24 | Providing and fixing ISI marked oxidised M.S. tower bolt black finish, (Barrel type) with necessary screws etc. complete: 9.63.3 150x10mm each 53.05 |
| 25 | Providing and fixing ISI marked oxidised M.S. handles conforming to IS: 4992 with necessary screws etc. complete 9.66.1 125mm each 35.20 |
| 26 | Providing and fixing bright finished brass hanging type floor door stopper with ncesssary screws, etc. complete each 109.60 |
| 27 | Providing and fixing M.S. grills of required pattern in frames of windows etc. with M.S plates, square or round bars ete. including priming coat with approved steel primer all complete 9.48.2 Fixed to openings/wooden frames with rawl plugs screws ete. kg 197.70 |
| 28 | Providing and fixing lу proof stainless steel grade 304 wire gauge to windows and clerestory windows using wire gauge with average wideth of aperture 1.4 mm in both directions with wire of dia. 0.50mm all complete 9.135.1 with 2nd class teak wood beading 62x19mm sam 1404.25 |
| 29 | Painting or varnishing new wood work in small areas with one coat (UP to One sq. meter) of ready mixed Priming paint and two coat of approved superior quality ready mixed paint or varnish including supply of all material labour and tools and plants etc. required for proper completion of the work. Paint to be used should confirem ISI No. 103-1950 (Unnwd item No-641 @ 60) |
| 30 | Providing and filling the joints with spun yarn, cement slurry and cement mortar 1:2 ( 1 cement : 2 fine sand) in S.C.I./ C.I. Pipes : 100 mm dia pipe |
| 31 | Providing and fixing water closet squatting pan (Indian type W.C. pan) with 100 mm sand cast Iron P or S trap, 10 litre low level white P.V.C. flushing cistern, including flush pipe with manually controlled device (handle lever) coforming to IS : 7231with all fitting and fixtures complete, including cutting and making good the walls and floors wherever required:17.1.1 White Vitreous china Orissa pattern W.C. Pan of size 580x440mm with integral type foot rests. |
| 32 | Providing and fixing soil, waste and vent pipes : 100 mm dia. Sand cast iron S&S pipe as per IS: 1729 |
| 33 | Providing and fixing 500 mm. 400mm. Wash hand basin of white glazed earthen ware Ist quality ISI Marked (Hindustan neyer, cera make) with RS or Cl brackets painted white 15mm dia ep brass pillar cock with CP metal handle (weigth not less than 400gms) ISI Marked and 32mm. dia CP brass chain with rubber plug 32mm din ep brass waste standard pattern with check nut 32mm dia CP brass Por S trap and unions complete with PVC connection 0.50 size including Supply of all required material labour T&P ete. required material labour T&P etc. required for proper completion of work and including cutting and making good the walls and floor with cement coares sand and grit fittings used should |
| 34 | Providing and fixing flate back 465mm x 355mm x265mm size lipped fron urinal basin of white glazed earthen ware Ist quality (Hindustan, neyeer make) ISI marked with 5 lits CI automatic flushing cisten (Hindustan sanfax Ashoka make) ISI Makred with necessary fitting RS or Cl bracket standard size 32mm dia G.I flush pipe \\"B\\" class with brass uinions of fittings and Gl waste pipe 25mm dia x 0.66 mm complete including supply of all amterials labour and T&P etc. required for proper compeletion of workk including painting of cistern and fittintgs with approved paint cutting and making good the wall and floors where required with cement sand and grit. |
| 35 | Providing and fixing P.V.C. waste pipe for sink or wash basin including P.V.C. waste fittings complete.Flexible pipe 32 mm dia |
| 36 | Providing And fixing Stainless Steel A ISI 304 (18/8) Kitchen Sing as per IS: 13983 with C.1. Brackets and Stainless steel Plug 40mm, Including Painting of Fittings and brackets, Cutting and Making good the walls wherever required. |
| 37 | Providing and fixing Chlorinated Polyvinyl chloride (CPVC) pipes, having thermal stability for hot & old water supply, including all CPVC plain & brass threaded fittings, including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and testing of joints complete as per direction of Engineer in Charge.Internal work - Exposed on wall. 25 mm nominal dia Pipes |
| 38 | Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, i/c fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and the cost of cutting chases and making good the same including testing of joints complete as per direction of Engineer in Charge. Concealed work, including cutting chases and making good the walls etc 25 mm nominal dia Pipes |
| 39 | Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, i/c fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and the cost of cutting chases and making good the same including testing of joints complete as per direction of Engineer in Charge. Concealed work, including cutting chases and making good the walls etc.20 mm nominal dia Pipes |
| 40 | Providing and fixing uplasticised PVC connection pipe with brass unions : 45 cm length 15 mm nominal bore |
| 41 | Providing and placing on terrace (at all floor levels) polyethylene water storage tank, IS : 12701 marked, with cover and suitable locking arrangement and making necessary holes for inlet, outlet and overflow pipes but without fittings and the base support for tank. |
| 42 | Providing and applying plaster of paris putty of 2 mm thickness of approved brand and manufacturar, over the plastered wall surface to prepare the surface even and smooth complete. |
| 43 | Wall painting with acrylic emulsion paint, having VOC (Volatile Organic Compound) content less than 50 grams/ litre, of approved brand and manufacture, including applying additional coats wherever required, to achieve even shade and colour.13.82.2 Two coats |
| 44 | Laying coarse sand under interlocking tile including all cost of labour, material T&P etc. complete as per engineer-in-charge. |
| 45 | Painting with synthetic enamel paint of approved brand and manufacture of required colour to give an even shade on iron work: 13.99.1 One or more coats on old work |
| 46 | Providing and fixing false ceiling at all height including providing and fixing of frame work made of special sections, power pressed from M.S. sheets and galvanized with zinc coating of 120 gms/sqm (both side inclusive) as per IS : 277 and consisting of angle cleats of size 25 mm wide x 1.6 mm thick with flanges of 27 mm and 37mm, at 1200 mm centre to centre, one flange fixed to the ceiling with dash fastener 12.5 mm dia x 50mm long with 6mm dia bolts, other flange of cleat fixed to the angle hangers of 25x10x0.50 mm of required length with nuts & bolts of required size and other end of angle hanger fixed with intermediate G.I. channels 45x15x0.9 mm running at the spacing of 1200 mm centre to centre, to which the ceiling section 0.5 mm thick bottom wedge of 80 mm with tapered flanges of 26 mm each having lips of 10.5 mm, at 450 mm centre to centre, shall be fixed in a direction perpendicular to G.I. intermediate channel with connecting clips made out of 2.64 mm dia x 230 mm long G.I.wire at every junction, including fixing perimeter channels 0.5 mm thick 27 mm high having flanges of 20 mm and 30 mm long, the perimeter of ceiling fixed to wall/partition with the help of rawl plugs at 450 mm centre, with 25mm long dry wall screws @ 230 mm interval, including fixing of gypsum board to ceiling section and perimeter channel with the help of dry wall screws of size 3.5 x 25 mm at 230 mm c/c, including jointing and finishing to a flush finish of tapered and square edges of the board with recommended jointing compound, jointing tapes, finishing with jointing compound in 3 layers covering upto 150 mm on both sides of joint and two coats of primer suitable for board, all as per manufacturer's specification and also including the cost of making openings for light fittings, grills, diffusers, cutouts made with frame of perimeter channels suitably fixed, all complete as per drawings, specification and direction of the Engineer in Charge but excluding the cost of painting with 12.5 mm thick tapered edge gypsum moisture resistant board. |
| 47 | Providing & Laying of Interlocking concrete block pavement having thickness of 80mm including all cost of labour, material T&P etc. |
| 48 | Providing and fixing aluminium die cast body tubular type universal hydraulic door closer (Having brand logo with ISI, IS: 3564, embossed on the body door weight upto 35 kg and door width upto 700mm) with necessary accessories and screws etc. complete. 9.83 |
| 49 | Providing & Fixing 5KW of grid solar system including all cost of material, labour, T&P etc. complete. |
| 50 | Providing and fixing toilet paper holder. C.P. brass |
| 51 | Providing and fixing plain bend of required degree.100 mm dia. Sand cast iron S&S as per IS - 1729 |
| 52 | Providing and laying non-pressure NP2 class (light duty) R.C.C. pipes with collars jointed with stiff mixture of cement mortar in the proportion of 1:2 (1 cement : 2 fine sand) including testing of joints etc. complete. 150 mm dia. R.C.C. pipe |
| 53 | Providing and fixing C.P. brass bib cock of approved quality conforming to IS:8931 : 15 mm nominal bore |
| 54 | Providing and fixing C.P. brass long body bib cock of approved quality conforming to IS standards and weighing not less than 690 gms.15 mm nominal bore |
| 55 | Providing and fixing PTMT grating of approved quality and colour. Rectangular type with openable circular lid. 150 mm nominal size square 100 mm diameter of the inner hinged round grating |
| 56 | Providing and fixing PTMT Ball cock of approved quality, colour and make complete with Epoxy coated aluminium rod with L.P./ H.P.H.D. plastic ball. 40mm nominal bore, 206mm long. Weighing not less than 690 gms. |
| 57 | Providing and fixing C.P. brass angle valve for basin mixer and geyser points of approved quality conforming to IS:8931 15 mm nominal bore |
| 58 | Providing and fixing CP Brass Single lever telephonic wall mixer of quality & make as approved by Engineer in charge. 15 mm nominal dia |
| 59 | Providing and fixing ball valve (brass) of approved quality, High or low pressure, with plastic floats complete. 25 mm nominal bore |
| 60 | Providing and fixing PTMT towel rail complete with brackets fixed to wooden cleats with CP brass screws with concealed fittings arrangement. 450 mm long towel rail with total length of 495 mm, 78 mm wide and effective height of 88 mm, weighing not less than 170 gms of approved quality and colour. |
| 61 | Providing and fixing PTMT soap Dish Holder having length of 138 mm, breadth 102 mm, height of 75 mm with concealed fitting arrangements, weighing not less than 106 gms. |
| 62 | Providing and fixing mirror of superior glass (of approved quality) and of required shape and size with plastic moulded frame of approved make and shade with 6 mm thick hard board backing : Oval shape 450x350 mm (outer dimensions) |
| 63 | Providing and fixing C.P. brass shower rose with 15 or 20 mm inlet.100 mm diameter |
| 64 | Providing and fixing 8 mm dia C.P. / S.S. Jet with flexible tube upto 1 metre long with S.S. triangular plate to Eureopean type W.C. of quality and make as approved by Engineer - in - charge. |
| 65 | Wiring for light point/Fan point/Exsust fan point/Call well with 1.5 sq. mm FRLS PVC insulated copper conductor single core cable in surface/recessed steel conduit, with piano type switch, phenolic laminated sheet, suitable size MS Box and earthing the point with 1.5 sq. mm FRLS. PVC Insulated copper conductor single core cable etc. As required. |
| 66 | Wiring for light/ Power Plug with 2X4 sq. mm FRLS PVC insulated copper conductor single core cable in surface/recessed medium class PVC conduit along with 1 no. 4 sq. mm FRLS. PVC Insulated copper conductor single core cable for loop earthing as required. |
| 67 | Wiring for circuit/ submain wiring alongwith earth wire with the following sizes of FRLS PVC insulated copper conductor, single core cable in surface/ recessed medium class PVC conduit as required.2 X 1.5 sq. mm + 1 X 1.5 sq. mm earth wire |
| 68 | Wiring for circuit/ submain wiring alongwith earth wire with the following sizes of FRLS PVC insulated copper conductor, single core cable in surface/ recessed medium class PVC conduit as required.2 X 2.5 sq. mm + 1 X 2.5 sq. mm earth wire |
| 69 | Wiring for circuit/ submain wiring alongwith earth wire with the following sizes of FRLS PVC insulated copper conductor, single core cable in surface/ recessed medium class PVC conduit as required.2 X 4 sq. mm + 1 X 4 sq. mm earth wire |
| 70 | Supplying and drawing following pair 0.5 mm dia FRLS PVC insulated annealed copper conductor, unarmored telephone cable in the existing surface/ recessed steel/ PVC conduit as required. 1 Pair |
| 71 | Supplying and fixing following modular switch/ socket on the existing modular plate & switch box including connections but excluding modular plate etc. as required. 5/6A switch |
| 72 | Supplying and fixing following modular switch/ socket on the existing modular plate & switch box including connections but excluding modular plate etc. as required. 15/16A switch |
| 73 | Supplying and fixing following modular switch/ socket on the existing modular plate & switch box including connections but excluding modular plate etc. as required. 3 pin 5/6A switch outlet |
| 74 | Supplying and fixing following modular switch/ socket on the existing modular plate & switch box including connections but excluding modular plate etc. as required. 6 pin 15/16A switch outlet |
| 75 | Supplying and fixing suitable size Gl box with modular plate and cover in front of surface or in recess, including providing and fixing 3 pin 5/6 A modular socket outlet and 5/6 A modular switch, connections etc. as required. |
| 76 | Supplying and fixing suitable size Gl box with modular plate and cover in front on surface or in recess, including providing and fixing 6 pin 5/6 & 15/16 A modular socket outlet and 15/16 A modular switch, connections etc. as required. |
| 77 | Installation, Testing, Commissioning of wall bracket /ceiling fittings of all sizes and shapes containing upto two GLS/CFL/LED lamps per fitting, complete with all accessories including connections etc. as required. |
| 78 | Supplying & fixing suitable size Gl box wih modular plate and cover in front of surface or in recess including providing and fixing 25 A modular socket outlet and 25 A modular SP MCB, \\"C\\" curve including connections, painting etc. as required. |
| 79 | Supplying and fixing metal box of 150mmx75mmx60mm deep (Nominal size) on surface or in recess with suitable size of phenolic laminated sheet cover in front including providing and fixing 3 pin 5/6 A Socket outlet and 5/6 A Piano type switch , connections painting etc. As required. |
| 80 | Supplying and fixing metal box of 180mmx100mmx60mm deep (Nominal size) on surface or in recess with suitable size of phenolic laminated sheet cover in front including providing and fixing 6 pin 5/6 And 15/16 A Socket outlet and 15/16 A Piano type switch , connections Painting etc.As required. |
| 81 | Supplying and fixing 5A to 32A rating, 240/415V, 10 KA \\"C\\" Curve miniature circuit breaker suitable for inductive load of following poles in the existing MCB DB complete with connections, testing and commissioning etc. As required. |
| 82 | Supplying and fixing factory wired H.P.F. box type flourcent tube light complete including tube etc. On surface complete in all respect of Phillips/Bajaj/Havells/Crompt. Make suitable for 1x40 wattwith flourcent tube |
| 83 | Supplying and fixing following rating double pole , 240 V isolator in the existing MCB DB complete with connections testing and commissioning etc. As required. |
| 84 | Supplying and fixing following rating, double pole, (single phase and neutral), 240 V, residual current circuit breaker (RCCB), having a sensitivity current 30 mA in the existing MCB DB complete with connections, testing and commissioning etc. as required. 40A |
| 85 | Earthing with copper earth plate 600 mm X 600 mm X 3 mm thick including accessories, and providing masonry enclosure with cover plate having locking arrangement and watering pipe of 2.7 metre long etc. with charcoal/coke and salt as required. |
| 86 | Supply, Installation, Testing and Commissioning of 1200 mm sweep, BEE 5 star rated, ceiling fan with Brush Less Direct Current (BLDC) Motor, class of insulation: B, 3 nos. blades, 30 cm long down rod, 2 nos canopies, shackle kit, safety rope, copper winding, Power Factor not less than 0.9, Service Value (CM/M/W) minimum 6.00, Air delivery minimum 210 Cum/Min, 350 RPM (tolerance as per IS: 374-2019), THD less than 10%, remote or electronic regulator unit for speed control and all remaining accessories including safety pin, nut bolts, washers, temperature rise=75 degree C (max.), insulation resistance more than 2 mega ohm, suitable for 230 V, 50 Hz, single phase AC Supply, earthing etc. complete as required. |
| 87 | Supply & fixing of 7 mtr GI Octagonal Pole of approved make (top dia 70mm, Bottom dia 130mm and base plate 12mm thik) having 3mm thikness with single arm bracket (1 Mtr length) on RCC foundation including the cost of foundation, foundation bolts, excavation & back filling and Required T&P completee in all respect. |
| 88 | Supplying & Fixing of Pre-cast Boundary wall of M25 Grade, with column spacing of 1.80 m c/c including all cost of material, labour and T&P etc. As per instruction of Engineer-in-Charge. Size - H Shape pillar - 150x150mm.Size - Pannel - Bayx300x50mm.Steel Details1- H Shape piller 8mm dia - 4 Nos x 2.40 m = 9.60 m x 0.39 per Kg/m = 3.744 kg 2- Pannel 6.00mm dia - 3 Nos x 1.80 m = 5.40 m x 0.22 per kg/m =1.190kg.Total Steel = 4.93 kg/mtr. |
| 89 | Finishing walls with Acrylic Smooth exterior paint of required shade: 13.46.1 New work (Two or more coats applied @ 1.67 ltr/10 sqm over and inclucing priming coat of exterior primer applied @ 0.90 litre/10 sqm |
| 90 | Earth work in excavation in foundation in all cost of labour material T&P etc/ complete Please Enable Macros to View BoQ information |
AI Tender Summary
Tender Timeline
Jul 09, 2026
11:30 IST
Tender Published
Tender notice published.
CompletedJul 16, 2026
17:00 IST
Bid Submission Deadline
Online submission via eProcurement portal.
Upcoming · 2 daysJul 16, 2026
Bid Opening Date
Technical bids will be opened and evaluated.
Upcoming · 2 daysTender Documents
Download All (ZIP) ↓
Disclaimer
We takes all possible care for accurate & authentic tender information. However users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender