Tender For Construction Of Civil Supplies Godown At Thalla, Bharmour, Distt. Chamba, Sh:- Building Portion Including Water Supply & Sanitary Installation, Septic Tank With Soak Pit, Rain Water Harvesting System, Site Developement.
Tender Value
2.34 Crore
Estimated cost
Bid Submission
15 Jul 2026
5 days left
EMD
4.68 Lakhs
Bank guarantee accepted
Document Fee
7000
Non-refundable
Tender Type
Online
Tender Overview
Organization
Tender ID
Competition Type
NCB
Bidding Type
Tender
Location / State
Chamba → Himachal Pradesh
EMD Exemption
Not Available
Quantity
Not Available
Website
Contact Person
Address
Project Description
Tender for Construction Of Civil Supplies Godown At Thalla, Bharmour, Distt. Chamba, Sh:- Building Portion Including Water Supply & Sanitary Installation, Septic Tank With Soak Pit, Rain Water Harvesting System, Site Developement.
BOQ
| Sl. No. | Item Description |
| 1 | Excavation work by mechanical means (hydraulic excavator)/ manual in all height and depths and in all kind of soil including saturated soils comprising of pick work, jumper work, pick jumper work, blasting work both in soft and hard rocks, chiseling/ wedging out of rock (where blasting is prohibited) and their intermediate classification of soil , setting out true to the required line, grades, width, cutting and trimming of side slopes as shown in the drawing and if water is met with in the excavation due to springs, seepage, rain and other causes it shall be removed by the suitable diversion pumping or bailling out and excavation shall be kept dry wherever so required by the contractor at his own cost as directed by the Engineer-In-Charge and disposal all surplus excavated soil in acquired width or at an approved dumping site including its stacking leveling dressing including all lead and lifts by head load, mechnical transportation or by any oyher mode of transportation with all cost of labours, machineries and other incidentals to complete the work as per HP PWD specification. Any loss to the public/ private property during the course of execution and disposal of unserviceble meterial shall be the absolute responsibility of the contractor which shall have to be compensated by him in all case. The rate is including octroi, royality, Malkana, toll tax, GST or other taxes imposed by the Government. |
| 2 | Excavation work by mechanical means (hydraulic excavator)/ manual in foundation trenches or drains in earth work of all kind of soil such as pick work, jumper work, blasting work, jumper blasting work soft and hard blasting and saturated soil, de-watering, including wedging out rocks where blasting is prohibited, chiseling or any other mixed variety of soil, including shoring, strutting or bailing out water upto any depth or any height quantum of water including dewatering removal of slush and stacking the serviceable and unserviceable material clear from the edge of excavation and as per direction of Engineer-In-Charge and returning the stacked soil in 15 cm (Fifteen centimetre) layers, when required into plinths, side of foundation etcetera consolidating each deposited layer by ramming watering and then disposing of all excavated earth as directed by the Engineer-In-Charge, within all leads, lifts and other incidentals as per specifications, approved drawing, design and as directed by the Engineer-In-Charge. The rate is inclusive of octroi, royality, Malkana, Toll tax, sale tax, GST and any other taxes imposed by the Government. |
| 3 | Excavation work by mechanical means (hydraulic excavator)/ manual overall areas in earth work of all kind of soil such as pick work, jumper work, blasting work, jumper blasting work soft and hard blasting and saturated soil, de-watering, including wedging out rocks where blasting is prohibited, chiseling or any other mixed variety of soil, including shoring, strutting or bailing out water upto any depth or any height quantum of water including dewatering removal of slush and stacking the serviceable and unserviceable material clear from the edge of excavation and as per direction of Engineer-In-Charge and returning the stacked soil in 15 cm (Fifteen centimetre) layers, when required into plinths, side of foundation etcetera consolidating each deposited layer by ramming watering and then disposing of all excavated earth as directed by the Engineer-In-Charge, within all leads, lifts and other incidentals as per specifications, approved drawing, design and as directed by the Engineer-In-Charge. The rate is inclusive of octroi, royality, Malkana, Toll tax, sale tax, GST and any other taxes imposed by the Government. |
| 4 | Excavating trenches of required width for pipes, cables, etcetera including excavation for sockets, and dressing of sides, ramming of bottoms, upto any depth including getting out the excavated soil, then returning the soil as required, in layers not exceeding 20 cm (Twenty centimetre) in depth, including consolidating each deposited layer by ramming, watering, etcetera and disposing of surplus materials/excavated soil as per specification, approved drawing, design, specification and as per the entire satisfaction of Engineer-In-Charge, including carriage of material within all leads, lifts and other incidentals as per specifications, approved drawing, design and as directed by the Engineer-In-Charge. The rate is inclusive of octroi, royality, Malkana, Toll tax, GST and any other taxes imposed by the Government. . |
| 5 | Consolidation of sub grade with Road Roller 8-10 (eight - ten) Tonne, including making good the undulation etcetera with earth or quarry soil etcetera and rerolling the sub-grade completed as per HP.PWD specifications including carriage of material within all leads, lifts and other incidentals, as per approved specifications drawing, design and as directed by the Engineer-In-Charge. The rate is inclusive of octroi, royality, Malkana, Toll tax, GST and any other taxes imposed by the Government. |
| 6 | Providing and construction of granular sub-base 150mm (one hundered fifty milimeters) compacted thickness by providing well graded materials as per table 400.1 spreading in uniform layers with tractor mount grader on prepared surface, mixing by mix in place method with rotavator at OMC, and compacting with three wheel roller 80-100 (Eighty-hundred) kN static roller to achieve the desired density, complete as per MORD Technical Specification section 400 for grading-I material, including carriage of material within all leads, lifts and other incidentals, as per approved specifications drawing, design and as directed by the Engineer-In-Charge. The rate is inclusive of octroi, royality, Malkana, Toll tax, GST and any other taxes imposed by the Government. |
| 7 | Providing, laying, spreading and compacting by mechanically means stone aggregate size 53mm to 22.4mm (fifty three millimeter to twenty two point four millimeter) Grading-III size [75mm( seventy five millimeters) compacted thickness] to water bound macadam specification including spreading in uniform thickness using template, hand packing, rolling with three wheel 80-100 (eighty-Hundred) K.N. static roller in stages to proper grade and camber, applying and brooming, stone screening type-B of size 11.2mm (eleven point two milimetres) nominal size at the rate of 0.18Per cubic metre (zero point eighteen) cubic metres per 10 Per square metre (per ten square metres) and to fill up the interstices of coarse aggregate, watering and compacting to the required density as per MORD technical specifications section 400 and as per the entire satisfaction and direction of Engineer–In-Charge including carriage of materials within all leads, lifts and other incidental. The rate is including octroi, royality, Malkhana, toll tax, GST and any other taxes imposed by the Government. |
| 8 | Supplying and filling in plinth with sand under floors,including watering, ramming, consolidating and dressing complete including carriage of material within all leads, lifts and other incidentals. The rate is inclusive of octroi, royality, Malkana, Toll tax, GST and any other taxes imposed by the Government. |
| 9 | Providing & Filling in plinth with hard stone under floors & stone boulder behind retaining walls, including watering, ramming, consolidating and dressing complete including carriage of material within all leads, lifts and other incidentals. The rate is inclusive of octroi, royality, Malkana, Toll tax, GST and any other taxes imposed by the Government. |
| 10 | Providing and laying mechanically mixed and vibrated plain cement concrete 1:4:8 (One cement isto four sand isto eight graded stone aggregate 40mm (Forty millimetre) nominal size) and curing complete excluding cost of form work in Retaining wall/return wall/ breast wall and foundation & plinth complete as per architectural drawings including carriage of material within all leads, lifts and other incidentals, as per approved specifications drawing, design and as directed by the Engineer-In-Charge. The rate is inclusive of octroi, royality, Malkana, Toll tax, GST and any other taxes imposed by the Government. |
| 11 | Providing and laying mechanically mixed and vibrated plain cement concrete 1:3:6 (One cement isto three sand isto six graded stone aggregate 40mm (Forty millimetre) nominal size) and curing complete excluding cost of form work in Retaining wall/return wall/ breast wall and foundation & plinth complete as per architectural drawings including carriage of material within all leads, lifts and other incidentals, as per approved specifications drawing, design and as directed by the Engineer-In-Charge. The rate is inclusive of octroi, royality, Malkana, Toll tax, GST and any other taxes imposed by the Government. |
| 12 | Providing and laying in position machine batched and machine mixed cement concrete work of grade M-20 (Twenty) design mix to obtain the minimum compressive strength of 20N/mm square (Twenty newton per square millimetre) with cement contents not not less than @ 320 Kilogram/Cubic metres (at the rate Three hundred twenty kilogram Per Cubic metre) or as per approved design mix. All works upto plinth level to give a smooth surfaces machanically mixed and vibrated including curing complete and pumping of concrete to site of laying but excluding the cost of centering, shuttering, finishing and reinforcement, including admixtures in recommended proportions as per IS: 9103 to accelerate, retard setting of concrete, improve workability without impairing strength and durability etcetera including carriage of material within all leads, lifts and other incidentals as per specifications, approved drawing, design and as directed by the Engineer-in-charge. The rate is inclusive of octroi, royality, Malkhana, Toll tax, GST and any other taxes imposed by the Government.. |
| 13 | Providing and laying in position machine batched and machine mixed cement concrete work of grade M-25 (Twenty five) design mix to obtain the comprehensive stment concrete work up to plinth level using minimum cement content not less than five Newton/Square millimetre) 400 KG/Cum (four hundred kilogram per cubic metre) or as per approved design mix to give a smooth mechanically mixed & vibrated including curing complete and pumping and reinforcement, including admixtures in recommended proportions as per pumping of concrete to site of laying but excluding the cost of centering, shuttering, 15: 9103 to accelerate, retard setting of concrete, improve workability without impairing strength and durability for reinforced concrete work complete including carriage of material within all leads, lifts and other incidental as per specifications approved drawing, design and as per direction of Engineer-in-charge. The rate is including octroi, royalty, Malkana, toll tax, GST and any other taxes imposed by the Government |
| 14 | Providing and laying in position machine batched and machine mixed cement Poncrete work of grade M-25 (Twenty five) design mix to obtain the comprehensive strength of 25 N/mm² (twenty five Newton/Square millimetre) concrete for reinforced cement concrete work up to all floor level using minimum cement content not less than 400 KG/Cum (four hundred kilogram per cubic metre) or as per approved design mix to give a smooth mechanically mixed & vibrated including curing complete and pumping of concrete to site of laying but excluding the cost of centering, shuttering, finishing and reinforcement, including admixtures in recommended proportions as per 15: 9103 to accelerate, retard setting of concrete, improve workability without impairing strength and durability for reinforced concrete work complete including carriage of material within all leads, lifts and other incidental as per specifications approved drawing, design and as per direction of Engineer-in-charge. The rate is including octroi, royalty, Malkana, toll tax, GST and any other taxes imposed by the Government |
| 15 | Providing plinth protection with 50 mm (Fifty millimetres) thick interlocking paver blocks of M -30 (M-thirty) grade of NTC or its equivalent with 23cm (Twenty three centimetres) diametre Half round stone ware pipe for drainage purpose laid over 25cm (twenty five centimetres) thick cement concrete 1:4:8 (One cement isto four sand isto eight graded) stone aggregate bedding complete as per architectural drawings including carriage of material within all leads, lifts and other incidentals, as per approved specifications drawing, design and as directed by the Engineer-In-Charge. The rate is inclusive of octroi, royality, Malkana, Toll tax, GST and any other taxes imposed by the Government. |
| 16 | Providing and laying 100mm (Hundered millimetre) thick faciory made cement concrete interlocking paver block of M-50 M-fifty) grade made by block making machine with strong vibratory compaction, of approved size, design & shape, laid in required colour and pattern over and including 50mm (fifty millimetre) thick compacted bed of coarse sand, filling the joints with fine sand etcetera all complete including carriage of material within all leads, lifts and other incidentals, as per approved specifications drawing, design and as directed by the Engineer-In-Charge. The rate is inclusive of octroi, royality, Malkana, Toll tax, GST and any other taxes imposed by the Government. |
| 17 | Providing and laying 110mm (one hundered ten millimetre) diametre with working pressure not less than 4.5 Per Kilogram/cm2 (four point zero five kilogram per centimetre square) ISI marked PVC pipe weep holes in brick masonry/stone masonry, plain reinforced concrete, Abutments, Wing walls, Return walls and retaining/breast walls extended through the full width of the structure with slope I(V) : 20(H) (One vertical isto Twenty Horizontal) towards draining face complete as per drawing and MORD technical specification section 700 and 1200 and as per direction of Engineer-In-Charge including carriage of materials within all leads, lifts and other incidentals. The rate is including octroi, royality, Malkhana, toll tax, GST and any other taxes imposed by the Government. |
| 18 | Providing form work with steel plates of 3.15mm (Three decimal one five millimetres) thick, welded with angle iron in frames of 30x30x5mm (Thirty into Thirty into Five millimetres), so as to give a fair finish including centring, shuttering strutting and propping etcetera, with wooden battens and ballies for all heights/depth of propping and centring below supporting floor to ceiling and removal of the same for in-situ reinforced concrete and plain concrete work in Foundation footings, bases of columns and mass concrete or other similar works including carriage of material within all leads, lifts and other incidentals as per specifications, approved drawing, design, entire satisfaction and as directed by the Engineer-In-Charge. The rate is inclusive of octroi, royality, Malkana, Toll tax, GST and any other taxes imposed by the Government. |
| 19 | Providing form work with steel plates of 3.15mm (Three decimal one five millimetres) thick, welded with angle iron in frames of 30x30x5mm (Thirty into Thirty into Five millimetres), so as to give a fair finish including centring, shuttering strutting and propping etcetera, with wooden battens and ballies for all heights/depth of propping and centring below supporting floor to ceiling and removal of the same for in-situ reinforced concrete and plain concrete work in flat surfaces such as soffits of suspended floors roofs, landings balconies and access platform or other similar works for upto plinth and all floors level including carriage of material within all leads, lifts and other incidentals and as directed by the Engineer-In-Charge. The rate is inclusive of octroi, royality, Malkana, Toll tax, GST and any other taxes imposed by the Government. |
| 20 | Providing form work with steel plates of 3.15mm (Three decimal fifteen millimetres) thick, welded with angle iron in frames of 30x30x5mm (Thirty into Thirty into Five millimetres), so as to give a fair finish including centring, shuttering strutting and propping etcetera, with wooden battens and ballies for all heights and removal of the same for in-situ reinforced concrete and plain concrete work in Vertical surfaces such as walls (any thickness) partitions and the like including attached pilasters buttresses, plinth and string courses, vertcal fins and other similar works complete upto plinth and all floors level including carriage of material within all leads, lifts and other incidentals as per approved drawing, design, specifications and as directed by the Engineer-In-Charge. The rate is inclusive of octroi, royality, Malkana, Toll tax, GST and any other taxes imposed by the Government. |
| 21 | Providing form work with steel plates of 3.15mm (Three decimal one five millimetres) thick, welded with angle iron in frames of 30x30x5mm (Thirty into Thirty into Five millimetres), so as to give a fair finish including centring, shuttering strutting and propping etcetera, with wooden battens and ballies for all heights/depths of propping and centring below supporting floor to ceiling and removal of the same for in-situ reinforced concrete and plain concrete work in columns, pillar, piers, abutments, post and struts square, rectangular, polygonal etcetera for upto plinth and all floors level complete including carriage of material within all leads, lifts and other incidentals as per approved drawing, design, specifications and as directed by the Engineer-In-Charge. The rate is inclusive of octroi, royality, Malkana, Toll tax, GST and any other taxes imposed by the Government. |
| 22 | Providing form work with steel plates of 3.15mm (Three decimal one five millimetres) thick, welded with angle iron in frames of 30x30x5mm (Thirty into Thirty into Five millimetres), so as to give a fair finish including centring, shuttering strutting and propping etcetera; with wooden battens and ballies for all heights/depths of propping and centring below supporting floor to ceiling and removal of the same for in-situ reinforced concrete and plain concrete work in beams, cantilevers, girders, lintels sides and soffits of beams haunchings, cantilevers, bressumers and lintels for upto plinth and all floors level complete including carriage of material within all leads, lifts and other incidentals as per approved drawing, design, specifications, entire satisfaction and as directed by the Engineer-In-Charge. The rate is inclusive of octroi, royality, Malkana, Toll tax, GST and any other taxes imposed by the Government. |
| 23 | Providing form work with steel plates of 3.15mm (Three decimal fifteen millimetres) thick, welded with angle iron in frames of 30x30x5mm (Thirty into Thirty into Five millimetres), so as to give a fair finish including centring, shuttering strutting and propping etcetera, with wooden battens and ballies for all heights and removal of the same for in-situ reinforced and plain concrete work in edges of slab and breaks in floors and walls any thickness for upto plinth and all floors level complete including carriage of material within all leads, lifts and other incidentals as per approved drawing, design, specifications and as directed by the Engineer-In-Charge. The rate is inclusive of octroi, royality, Malkana, Toll tax, GST and any other taxes imposed by the Government. |
| 24 | Providing form work with steel plates of 3.15mm (Three decimal fifteen millimetres) thick, welded with angle iron in frames of 30x30x5mm (Thirty into Thirty into Five millimetres), so as to give a fair finish including centring, shuutering, strutting and propping etcetera with wooden battens and ballies for all height/depths and removal of the same for in situ-reinforced concrete & plain concrete work in window sills, cornice and moulding and the like upto all floors level including carriage of material within all leads, lifts and other incidentals as per specifications, approved drawing, design, specifications and as directed by the Engineer-In-Charge. The rate is inclusive of octroi, royality, Malkana, Toll tax, GST and any other taxes imposed by the Government. |
| 25 | Providing form work with steel plates of 3.15mm (Three decimal fifteen millimetres) thick, welded with angle iron in frames of 30x30x5mm(Thirty into Thirty into Five millimetres),so as to give a fair finish including centring, shuttering strutting and propping etcetera, with wooden battens and ballies for all heights and removal of the same for in-situ reinforced and Chullah hoods, weather shades, chhajjas, corbels etc. including edges, upto plinth and all floors level complete including carriage of material within all leads, lifts and other incidentals as per approved drawing, design, specifications and as directed by the Engineer-In-Charge. The rate is inclusive of octroi, royality, Malkana, Toll tax, GST and any other taxes imposed by the Government. |
| 26 | Providing and erection of Tor steel reinforcement Thermo Mechanically Treated bars of grade Fe-550D (five hundered fifty -D ) of Sail / TATA for reinforced cement concrete work including bending, binding, cutting, straightening and placing in position complete including cost of binding wires complete upto all floor levels as per approved specifications, drawing, design, as per entire satsfaction of the Engineer-In-Charge including carriage of material within all leads, lifts and other incidentals. The rate is inclusive of octroi, royality, Malkana, Toll tax, GST and any other taxes imposed by the Government. |
| 27 | Providing, fabrication and erection in position structural steel work of Tata / Sail / Reliance/Jindal Steel work welded in built up sections, in railing, brackets, gates, gratings framed guard bars, stringers, treads, landings etcetera of stair cases, including use of chequered plate and other similar works wherever required including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer using structural steel etcetera as required and works as per approved make all complete as per architectural drawings including carriage of material within all leads, lifts and other incidentals, as per approved specifications, drawing, design and as directed by the Engineer-in-charge. The rate is inclusive of octroi, royality, Malkhana, Toll tax, GST and any other taxes imposed by the Government. |
| 28 | Providing, fabrication and erection in position structural steel work of Tata / Sail / Reliance/Jindal riveted, bolted or welded in built up sections, trusses and framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer all complete as per architectural drawings including carriage of material within all leads, lifts and other incidentals, as per approved specifications, drawing, design and as directed by the Engineer-in-charge. The rate is inclusive of octroi, royality, Malkhana, Toll tax, GST and any other taxes imposed by the Government. |
| 29 | Providing and fixing Stainless Steel 316 (three hundered sixteen) grade, 50 mm (Fifty millimetres) or 38 mm (Thirty eight millimetres) diametre SST (Stainless steel) pipe handrail fixed with 35mm (Thirty five millimetres) diametre stainless steel baluster, as per detail in combination of 35mm (Thirty five millimetres) and 15/20mm (Fifteen or twenty millimetres) diametre SST pipe baluster knock down railing of KICH or its equivalent hand rail fixed on 10x50mm (Ten into fifty millimetres) stainless steel flat balusters, (DESIGN CODE DT53-2-163) placed at 1200 mm (One thousand two hundered millimetres) centre to centre along with 3 nos (Three Numbers) @ 16 mm (Sixteen millimetres) mid rail connected at the side of the baluster with fixtures. The baluster would be fixed on the floor with casted base plate minimum 6mm (six millimetre) thick base plate shall be concealed with suitable Stainless Steel 316 (three hundered six) grade cover cap railing made of Hollow tubes, channels, plates etcetera, including welding, grinding, buffing, polishing and making curvature (wherever required) and fitting the same with necessary stainless steel nuts and bolts complete, including fixing the railing with necessary accessories & stainless steel dash fasteners , stainless steel bolts etcetera, of required size, on the top of the floor or the side of waist slab with suitable arrangement complete as per architectural drawings including carriage of material within all leads, lifts and other incidentals, as per approved specifications drawing, design and as directed by the Engineer-in-charge. The rate is inclusive of octroi, royality, Malkana, Toll tax, GST and any other taxes imposed by the Government. |
| 30 | Providing and fixing angle iron frames for doors, windows and ventilators of Tata / Sail / Reliance/Jindal hisar having mild steel channel sections of size 75x40x4mm (seventy five into forty into four millimetre) and Mild Steel angle 25x20x3mm (twenty five into twenty into three millimetre), joints mitred and welded by Mild Steel flat iron 40x12mm (forty into twelve millimetre) to the existing T- iron frame size 25x25x3mm (twenty five into twenty five into three millimetre), and Z-sections as per detail to the wall with dash fastener, including fixing of necessary butt hinges and screws and applying a priming coat of approved steel primer complete as per architectural drawings including carriage of material within all leads, lifts and other incidentals, as per approved specifications drawing, design and as directed by the Engineer-in-charge. The rate is inclusive of octroi, royality, Malkana, Toll tax, GST and any other taxes imposed by the Government. |
| 31 | Providing and fixing Single rebate angle iron door,window,clerestory window frame manufactured from steel iron section of 40X40X5mm, (forty millimetre into forty millimetre into five millimetre) thickness including hinges jamb,lock jamb,beed and if required angle thrashold ofmild steel angle 50X25 mm (fifty millimetre into twenty five millimetre) welded or rigidly fixed by mechanical means,lugs with split end tails to each jamb including steel butt hinges 2.5 mm (two point five millimetre) thick with provision for locking arrangement and shock absorber as specified and applying a coat of approved steel primer after pre-treatment of the surface etcetera including carriage of material within all leads, lifts and other incidentals as per specifications, approved drawing, design and as directed by the Engineer-in-charge. The rate is inclusive of octroi, royality, Malkhana, Toll tax, sale tax, GST and any other taxes imposed by the Government. |
| 32 | Providing and fixing first class deodar wood work in frames of doors,windows, clerestory windows and other frames,wrought framed and fixed in position with hold fast lugs or with dash fasteners of required diametre & length , including carriage of material within all leads, lifts and other incidentals as per approved drawing, design, specifications and as directed by the Engineer-in-charge. The rate is inclusive of octroi, royality, Malkana, Toll tax, GST and any other taxes imposed by the Government. |
| 33 | Providing and Fixing factory made single rebate door frame fabricated from sections roll formed out of 1.2mm (one point two millimetre) thick galvanized steel (Base steel as per IS 513) with zinc of 120 gms/sq.mtr (one hundered twenty grams per square millimetre). The overall size of the section should be 105x60mm (One hundered five into sixty millimetre) with rebate of 37mm (thirty seven millimetre) for shutter. The frame section should be cut to length and metre joined with corner brackets made of CRCA electroplated. The frame should be provided with (a) 3 Nos. (three numbers) of M.S. powder coated 4” /100mm (One hundered millimetre) Butt hinges of 2mm (two millimetre) thickness welded to the frame. (b) 6 Nos. (six numbers) of 1.2mm (one point two millimetre) thick CRCA electroplated stiffeners should be welded to frame. (c) 6 Nos. (six numbers) of 8” /200mm (two hundered millimetre) M.S. hold fasts with split end tail welded to stiffener plates. (d) One number aldrop receiver.(e) Each frame should be provided with 25x50mm (Twenty five into fifty millimetre) tie rod at bottom. All welded places should be treated with protective coat of zinc rich primer. The entire frame should be provided with a coat of etched primer., all complete as per manufacturer's specification and direction of Engineer-In-Charge. The rate is inclusive of octroi, royality, Malkhana, Toll tax, sale tax, GST and any other taxes imposed by the Government. |
| 34 | Providing and fixing double rebate door frame fabricated from sections roll formed out of 1.2mm (one point two millimetre) thick galvanized steel (Base steel as per IS 513) with zinc of 120 gms/sq.mtr (one hundered twenty grams per square metre). The overall size of the section should be 125x60mm (One hundered twenty five into sixty millimetre). The frame section should be cut to length and meter joined with corner brackets made of CRCA electroplated. The frame should be provided with (a) 3 Nos. (three numbers) of M.S. powder coated 100mm ( one hundered millimetre) Butt hinges of 2mm (two millimetre) thickness welded to the frame. (b) 6 Nos. (six numbers) of 1.2mm (one point two millimetre) thick CRCA electroplated stiffeners should be welded to frame. (c) 6 Nos. (six numbers) of 200mm (two hundered millimetre) M.S. hold fasts with split end tail welded to stiffener plates. (d) One number aldrop receiver.(e) Each frame should be provided with 25x50mm (Twenty five into fifty millimetre) tie rod at bottom. All welded places should be treated with protective coat of zinc rich primer. The entire frame should be provided with a coat of etched primer., all complete as per manufacturer's specification and direction of Engineer-In-Charge. The rate is inclusive of octroi, royality, Malkhana, Toll tax, GST and any other taxes imposed by the Government. |
| 35 | Providing and fixing cold roll formed section of NCL section color 5000 (five thousand) Series or Elixir 3000 (three thousand) series Windows fabricated from roll formed sections made of Galvanized Steel Colour Coated/Powder Coated (Base Steel as per IS 513“D”quality,Galvanized as per IS 277 (Indian Standard two seven seven) with Zinc of 120 (one hundered twenty gramsper square metre) grams/Sq.Mtr.) with total coated thickness of 0.60mm (zero point six zero millimtre) with Coated Sectionss hould be with Primer Coat of Epoxy Primer of 5-7 (five to seven)microns thick, finish painted with Polyester Paint of 12-16 (twelve to sixteen) micron thick and back coated with Alkyd backer of 5-7 (five to seven) microns,or Powder Coated with pure Polyester Powder upto 50-60 (fifty to sixty)microns thick. Section for Frame should be of 98mmX50mm ( ninety eight into fifty millimetre) Section for Mullion should be of 46mm x 70 mm (forty six into seventy millimetre) ,Section for Shutter Frame s should be of 46mmX46mm (forty six into forty six millimetre), Section for Fixed Glass Bead should be of 18mm x 25mm (eighteen into twenty five millimetre) and Section for Flymesh Shutter Frame should be of 20mm x 40mm, (twenty into forty millimetre) Frame and Mesh Shutter Sectionsshould be cut to length and mitre joined with Corner Bracket made of Polypropylene.Glass Shutter should be mitre joined with corner brackets made of CRCA electroplated.Mullion Section should be joined with Frame/Mullion using Nylon Mullion Cap EthylPropylene Diamine Monomer (EPDM) Gasket should be used all around glass in shutter between Frame and Glazed Shutter and both sides of Fixed Glass.Frame should be fixed to brick/concrete masonary by using Nylon self expanding caps and driving MS electroplated 80mm (eighty millimetre) long screws into the caps through frames including MS Powder Coated Friction Hinges,S.S.Pivot Hinges, High Grade Aluminum Powder Coated Handle including carriage of material upto all leads and lift as per direction of Engineer-In-Charge. |
| 36 | Providing and fixing 65 x 100mm (sixty five into one hundered millimetre) factory made single extruded WPC (Wood Polymer Composite) solid doors/ windows / Celestory windows & other Frames / Chowkhat approved make of Alstone, Floresta, Ecoste, Century ply, comprising of virgin PVC polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/ wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) fabricated with miter joints after applying PVC solvent cement and screwed with ful body threaded star headed SS screws having minimum frame density of 850 Kilogram/Per Cubic metre (Eight hundered fifty kilogram per Per Cubic metre), screw withdrawal strength of 2200N (Face) & 1100N (Edge), minimum compressive strength of 58N/mm2 (fifty eight newton per millimetre square), modulus of elasticity 900N/mm2 (Nine hundered newton per millimetre square), and resistance to spread of flame of CIass A category with property of being Termite / borer proof, water / moisture proof and Fire retardant and fixed in position with M.S hold fast / lugs / SS dash fasteners of required diametre and length including carriage of material within all leads, lifts and other incidentals as per approved drawing, design, specifications and as directed by the Engineer-in-charge. The rate is inclusive of octroi, royality, Malkana, Toll tax, GST and any other taxes imposed by the Government. |
| 37 | Providing and fixing 40mm thick first Class deodar wood panelled or panelled and glazed shutters for doors windows and clerestory windows having top rail 100x40mm (One hundered into forty millimetre), style 100x40mm (One hundered into forty millimetre), middle rail 150 x 40mm (One hundered fifty into forty millimetre) and bottom rail shall be 200 x 40mm (Two hundered into forty millimetre) infill with 16mm (sixteen millimetre) thick 2nd class deodar wood wooden plank including brass butt hinges with necessary screws and 12x17.5mm (Twelve into seventeen point five millimetre) wooden beading, and lipping/ outer moulding 50x12.5mm (Fifty into twelve point five millimetre), complete as per architectural drawings specifications, design and as per the directions of Engineer-in-charge. The rate is inclusive of octroi, royality, Malkana, Toll tax, sale tax, GST and any other taxes imposed by the Government. |
| 38 | Providing and fixing 35mm (Thirty millimetre) thick both side commercial phenol bonded ISI Marked flush door shutter of CENTURY/ALPRO/ DURO PLY / GREEN PLY No.1S-2202 decorative type, core of block board construction to be finished with mica lamination of approved shade with frame of 1st (first) class hard wood and well matched ply veneering with vertical grain or cross bands and face veneering on both faces of shutters including black enameled Stainless steel butt hinges with necessary screws etcetera complete as per specifications, drawing and design including carriage of material within all leads, lifts and other incidentals and as directed by the Engineer-In-Charge. The rate is inclusive of octroi, royality, Malkana, Toll tax, GST and any other taxes imposed by the Government. |
| 39 | Providing and fixing to existing door frames 30mm (Thirty millimetre) thick factory made Prelaminated PVC door shutter consisting of frame made out of M.S. tubes of 19 (Nineteen) gauge thickness and size of 19x19mm (Nineteen into nineteen millimetre) for styles and 15x15mm (Fifteen into fifteen millimetre) for top & bottom rails, (Code no 9.120 ) of Rajshri M.S. frame shall have a coat of steel primers of approved make and manufacture M.S. frame covered with 5mm thick heat moulded PVC \\"C\\" channel of size 30mm (Thirty millimetre) thickness, 70mm (Seventy millimetre) width out of which 50mm (Fifty millimetre) shall be flat and 20mm (Twenty millimetre) shall be tappred in 45 (Forty five) degree angle on either side forming style and 5mm (Five millimetre) thick, 95mm (Ninety five millimetre) wide, PVC sheet out of which 75mm shall be flat and 20mm (Twenty millimetre) shall be tapered in 45o (Forty five degree) on the inner side to form top and bottom rail and 115mm (One hundered fifteen millimetre) wide PVC sheet out of which 75mm (Seventy five millmetre) shall be flat and 20mm (Twenty millimetre) shall be tapered on both side to form lock rail, top, bottom and lock rail shall be provided either side of the panel 10mm (Ten millimetre) thick, 20mm (Twenty millimetre) wide cross PVC sheet be provided as gap insert for top rail and bottom rail paneling of 5mm thick both side PVC Sheet to be fitted in the M.S. frame welded/sealed to the style & rails, joints mitred and jointed with solvent cement adhesive includingfixing of PVC shutter with existing frame with M.S. butt hinges 100x50x1.90mm (One hundered into fifty into One point nine zero millimetre) size with necessary screws etcetera complete including carriage of material within all leads, lifts and other incidentals as per specifications, approved drawing, design and as directed by the Engineer-in-charge. The rate is inclusive of octroi, royality, Malkhana, Toll tax, sale tax, GST and any other taxes imposed by the Government. |
| 40 | Providing and fixing 25mm (twenty five millimetre) thick Commercial Board water proof shutters with PGI sheet lining inside in SDB shutter including fixing with SS-304 (three hundered four) butt hinges with screws etcetera of Nova pan / Kit ply / National /Archidply / Action Tesa/ Green Ply complete including carriage of material within all leads, lifts and other incidentals as per specifications, approved drawing, design and as directed by the Engineer-In-Charge. The rate is inclusive of octroi, royality, Malkhana, Toll tax, GST and any other taxes imposed by the Government. |
| 41 | Providing and fixing 6.0 mm (six milimetre) thick toughened glass panes (weight not less than 15.00 Kilogram/ Square Metre) (Fifteen point zero zero kilogram per sqaure metre) Glass panes of Modi Guard/Saint Gobain/AIS/Atul/Gold Plus in door, window, ventilator shutters and partitions etcetera with EPDM / neoprene gasket etcetera complete including carriage of material within all leads, lifts and other incidentals as per specifications, approved drawing, design and as directed by the Engineer-in-charge. The rate is inclusive of octroi, royality, Malkhana, Toll tax, GST and any other taxes imposed by the Government. |
| 42 | Providing and fixing 5.0mm (Five millimetre) thickness float glass panes (weight not less than 12.5 Kilogram/ Square metre) (Twelve point five kilogram per sqaure metre)of Modi Guard / Saint Gobain / AIS / Atul / Gold Plus in door, window, ventilator shutters and partitions etcetera with EPDM rubber / neoprene gasket etcetera complete including carriage of material within all leads, lifts and other incidentals as per specifications, approved drawing, design and as directed by the Engineer-in-charge. The rate is inclusive of octroi, royality, Malkhana, Toll tax, GST and any other taxes imposed by the Government. |
| 43 | Providing and fixing 5.0mm (Five millimetre) thick froasted glass panes (weight not less than 12.5 Kilogram/ Square metre) (Twelve point five kilogram per sqaure metre) Glass panes of Modi Guard / Saint Gobain / AIS / Atul / Gold Plus in door, window, ventilator shutters and partitions etcetera with EPDM rubber / neoprene gasket etcetera complete including carriage of material within all leads, lifts and other incidentals as per specifications, approved drawing, design and as directed by the Engineer-In-Charge. The rate is inclusive of octroi, royality, Malkhana, Toll tax, GST and any other taxes imposed by the Government. |
| 44 | Providing and fixing Fly proof stainless steel grade 304 (three hundered four) wire guage with 0.5mm (Zero point five millimetres) diametre wire and 1.4mm (One point four millimetres) wide aperture for doors windows and clerestory windows with necessary screws complete as per architectural drawings including carriage of material within all leads, lifts and other incidentals, as per approved specifications drawing, design and as directed by the Engineer-in-charge. The rate is inclusive of octroi, royality, Malkana, Toll tax, GST and any other taxes imposed by the Government. |
| 45 | Providing and fixing M.S. (Mild steel) grills of require pattern in wooden/steel frames of windows etcetera with 12 x 6mm (Twelve into six millimetre)Mild Steel Flats in combination with 10 x 10 (Ten into Ten millimetre)mm square bars with round headed bolts and nuts or by screws complete all as per Drawing and Techanical Specifications including entire carriage of materials within all leads, lifts and other incidentals, as per approved and as directed by the Engineer-in-Charge. The rate is inclusive of octroi, royality, Malkhana, Toll tax, GST and any other taxes imposed by the Government. |
| 46 | Supplying and fixing rolling shutters of approved make made of 80mm x 1.25mm (Eighty into One point two five millimetre) M.S. Laths interlocked together through their entire length and joined together at the end by end locks mounted on specially designed pipe shaft with brackets side guides and arrangements for inside and outside locking with push pull operation complete but excluding the cost of the top cover and spring shutters , as per specification, approved drawing, design, as per entire satisfaction and direction of the Engineer-In-Charge including carriage of material within all leads, lifts and other incidentals. The rate is inclusive of octroi, royality, malkhana, toll tax, sale tax, GST and any other taxes imposed by the Government. |
| 47 | Providing and fixing 0.60 mm (Zero point sixty millimetres) thick prepainted steel sheet (ISI Marked-Z 120) of Tata Durashine or its equivalent, in roofing with hot dipped metallic zinc coated sheet with top coat of regular modified polyster (RNP) organic coating of 20 (Twenty) microns over 5 (Five) microns primer coating to back coat of polyster of 5 (Five) microns over 5 (Five) microns primer coating including fixing with prepainted iron J or L hooks, bolts and nuts 6mm (Six millimetre) diametre with prepainted limpet and rubber washers complete as per architectural drawings including carriage of material within all leads, lifts and other incidentals, as per approved specifications drawing, design and as directed by the Engineer-in-charge. The rate is inclusive of octroi, royality, Malkana, Toll tax, GST and any other taxes imposed by the Government. |
| 48 | Providing and fixing factory made ridges or hips having proper gola shape 60 cm (Sixty centimetres) overall with 0.60 mm (Zero point sixty millimetres) thick prepainted steel sheets of Tata Durashine or its equivalent in roofing with hot dipped metalic zinc coated sheets with top coat of regular modified polyster organic coating of 20 (Twenty) microns over 5 (Five) microns primer coating + back coat of polyster of 5 (Five) microns over 5 (Five) microns primer coating fixing with prepainted iron J or L hooks, bolts & nuts 6mm (Six millimetres) dia & prepainted G.I. limpet and bitumen washers complete as per architectural drawings including carriage of material within all leads, lifts and other incidentals, as per approved specifications drawing, design and as directed by the Engineer-In-Charge. The rate is inclusive of octroi, royality, Malkana, Toll tax, GST and any other taxes imposed by the Government. |
| 49 | Providing and fixing valley 90cm (Ninety centimetres) overall 0.60mm (Zero point sixty millimetres) thick prepainted steel sheet of Tata Durashine or its equivalent steels in roofing with hot dipped metalic zinc coated sheet with top coat of regular modified polyster organic coating of back coat of polyster of 5 (five) microns over 5 (five) microns primer coating including fixing with prepainted iron J or L hooks, bolts and nuts 6mm (six millimetres) dia with prepainted G.I. limpet and bitumen washers complete as per architectural drawings including carriage of material within all leads, lifts and other incidentals, as per approved specifications, drawing, design and as directed by the Engineer-In-Charge. The rate is inclusive of octroi, royality, Malkhana, Toll tax, GST and any other taxes imposed by the Government. |
| 50 | Providing and fixing flushing 38cm (Thirty eight centimetre) overall with 0.60mm (Zero point six zero millimetre) thick prepainted sheet of Tata Durashine or its equivalent in roofing with hot dipped metalic zinc coated sheet with top coat of regular modified polyster organic coating of 20 microns over 5 microns primer coating + back coat of polyster of 5 (Five) microns over 5 (Five) microns primer coating including fixing with prepainted iron J or L hooks, bolts and nuts 6mm (Six millimetre) dia meter and prepainted G.I. limpet and bitumen washers complete as per architectural drawings including carriage of material within all leads, lifts and other incidentals, as per approved specifications, drawing, design and as directed by the Engineer-In-Charge. The rate is inclusive of octroi, royality, Malkhana, Toll tax, GST and any other taxes imposed by the Government. |
| 51 | Providing and fixing 0.80 mm (Zero decimal eight millimetre) thick with zinc coating not less than 275 gm/m² (two hundered seventy five millimetre gram per square millimetre), 30cm (thirty centimetre) wide and 25cm (twenty five centimetre) deep, 80cm (eight centimetre) overall semi-circular / finished U-shaped as per design / plain prepainted G.S sheet gutter of Tata Durashine or its equivalent with iron brackets 40x3mm (forty into three millimetre) size, bolts, nuts and washers etcetera, including proving & fixing dome shape grating and making necessary connections with rain water pipes complete as per architectural drawings including carriage of material within all leads, lifts and other incidentals, as per approved specifications, drawing, design and as directed by the Engineer-in-charge. The rate is inclusive of octroi, royality, Malkhana, Toll tax, GST and any other taxes imposed by the Government. |
| 52 | Providing and fixing Mild Steel B.P. sheet 2.0mm (Two point zero millimetres) thick eaves board/facia/soffits/ceiling of Tata/ Sail/ Jindal hisar including cutting, fixing and welding to steel roof members and applying a coat of red lead primer complete as per the instruction of Engineer-Incharge (Base members of steel work shall be measured and paid separately) including fixing complete as per architectural drawings including carriage of material within all leads, lifts and other incidentals, as per approved specifications drawing, design and as directed by the Engineer-in-charge. The rate is inclusive of octroi, royality, Malkana, Toll tax, GST and any other taxes imposed by the Government. |
| 53 | Providing and fixing 0.5mm (Zero pint Five millimetre) thick GI Metal with perforated Tegular edge global white color tiles false ceiling tiles of Size 595x595mm (five hundered ninety five into five hundered ninety five millimetre) of Gyproc, Armstrong, Everest as per approved texture, design and patterns having with 8mm (Eight millimetre) and must be atleast 20% of perforation area with 1.8mm diametre hole work consisting of T-sections and L sections suitably fixed according to tile size complete including carriage of material within all leads, lifts and other incidentals, as per approved specifications drawing, design and as directed by the Engineer-In-Charge. The rate is inclusive of octroi, royality, Malkana, Toll tax, GST and any other taxes imposed by the Government. |
| 54 | Providing and fixing mild steel brackets made of vertical post 100x50mm (hundered into fifty millimetre), main frame of 50x50x3.0mm, ( fifty in to fifty in to three millimetre ) distribution member shall be 25x25mm of, hollow pipe of specified shape, projecting 450mm (four hundered fifty millimetre) outside the wall surface and 450mm (four hundered fifty millimetre) length fixed on wall with 4 (four) numbers, 6mm (six millimetre) diametre expansion hold fasteners, including drilling necessary holes in brick wall/ CC/ RCC surface and the cost of bolts etcetra The side M.S flat for brackets & centre piece shall be welded and fixed with M.S. nuts, bolts, & washers of size 25x6mm (twenty five into six millimetre), one bolts on Each side on the both sides of 50x50mm (fifty into fifty millimetre) hollow pipe, total length is 900mm (nine hundered millimetre) and angular length is 425mm (four hundered twenty five millimetre) including fixing complete as per architectural drawings including carriage of material, within all leads, lifts and other incidentals, as per approved specifications, drawing, design and as directed by the Engineer-in-charge. The rate is inclusive of octroi, royality, Malkhana, Toll tax, sale tax, GST and any other taxes imposed by the Government. |
| 55 | Providing and laying of brick work using Second class common burnt clay building bricks in super-structure upto all floor level in cement mortar 1:6 (One cement isto Six sand) and curing complete including carriage of material within all leads, lifts and other incidentals as per approved specifications, drawing, design and as directed by the Engineer-In-Charge. The rate is inclusive of octroi, royality, Malkana, Toll tax, GST and any other taxes imposed by the Government. |
| 56 | Providing and laying of half brick masonary with second class common burnt clay F.P.S. (non modular) bricks of class designation 7.5 (Seven point five) in superstructure above plinth up to all floor level in cement mortar 1:4 (One cement isto four sand) and curing complete including carriage of material within all leads, lifts and other incidentals as per approved specifications, drawing, design and as directed by the Engineer-In-Charge. The rate is inclusive of octroi, royality, Malkana, Toll tax, GST and any other taxes imposed by the Government. |
| 57 | Providing and laying of random rubble masonry with hard stone in foundation, plinth, retaining or returning/breast walls and other similar works including levelling up with cement concrete 1:6:12 (one cement isto six coarse sand isto twelve graded stone aggregate 20 mm (twenty millimetre) nominal size) upto plinth level with Cement mortar 1:6 (one cement isto six coarse sand) complete including carriage of material within all leads, lifts and other incidentals as per specifications, approved drawing, design and as directed by the Engineer-In-Charge. The rate is inclusive of octroi, royality, Malkana, Toll tax, GST and any other taxes imposed by the Government. |
| 58 | Providing and plastering 15mm (Fifteen millimetres) thick cement plasters in single coat on fair side of brick/concrete/ stone walls for interior/exterior plastering upto all floor level including arises, internal rounded angles, chamfers and or rounded angles not exceeding 80mm (Eighty millimetres) in girth and finished even and smooth with cement mortar 1:3 (One cement isto three sand) above plinth level to all floor level complete as per architectural drawings including carriage of material within all leads, lifts and other incidentals, as per approved specifications drawing, design and as directed by the Engineer-In-Charge. The rate is inclusive of octroi, royality, Malkana, Toll tax, GST and any other taxes imposed by the Government. |
| 59 | Providing and plastering 15mm (Fifteen millimetres) thick cement plasters in single coat on fair side of brick/concrete/ stone walls for interior/exterior plastering upto all floor level including arises, internal rounded angles, chamfers and or rounded angles not exceeding 80mm (Eighty millimetres) in girth and finished even and smooth with cement mortar 1:6 (One cement isto six sand) above plinth level to all floor level complete as per architectural drawings including carriage of material within all leads, lifts and other incidentals, as per approved specifications drawing, design and as directed by the Engineer-In-Charge. The rate is inclusive of octroi, royality, Malkana, Toll tax, GST and any other taxes imposed by the Government. |
| 60 | Providing and plastering 15mm (Fifteen millimetres) thick cement plasters in two coat on rough side of brick/concrete/stone walls for interior/exterior plastering upto all floor level including arises, internal rounded angles, chamfers and or rounded angles not exceeding 80mm (Eighty millimetres) in girth and finished even and smooth with cement mortar 1:6 (One cement isto six sand) above plinth level to all floor level complete as per architectural drawings including carriage of material within all leads, lifts and other incidentals, as per approved specifications drawing, design and as directed by the Engineer-In-Charge. The rate is inclusive of octroi, royality, Malkana, Toll tax, GST and any other taxes imposed by the Government. |
| 61 | Providing and plastering 6mm (Six millimetres) thick cement plaster to ceiling in cement mortar 1:3 (One cement isto three sand) complete as per architectural drawings including carriage of material within all leads, lifts and other incidentals, as per approved specifications drawing, design and as directed by the Engineer-In-Charge. The rate is inclusive of octroi, royality, Malkana, Toll tax, GST and any other taxes imposed by the Government. |
| 62 | Providing and plastering 15mm (Fifteen millimetres) thick cement plasters in single coat on fair side of brick/concrete/ stone walls for exterior plastering upto all floor level including arises, internal rounded angles, chamfers and or rounded angles not exceeding 80mm in girth and finished even and smooth with cement mortar 1:5 (One cement isto five sand) above plinth level to all floor level complete as per architectural drawings including carriage of material within all leads, lifts and other incidentals, as per approved specifications drawing, design and as directed by the Engineer-In-Charge. The rate is inclusive of octroi, royality, Malkana, Toll tax, GST and any other taxes imposed by the Government. |
| 63 | Providing and plastering 12mm (twelve millimetre) thick and 100mm (One hundered millimetre) wide plain cement mortar bands in cement mortar 1:4 (one cement isto four fine sand) surface of brick/concrete/ stone walls for exterior plastering upto all floor level including arises, internal rounded angles, chamfers and or rounded angles including carriage of material within all leads, lifts and other incidentals, as per approved specifications drawing, design and as directed by the Engineer-In-Charge. The rate is inclusive of octroi, royality, Malkana, Toll tax, GST and any other taxes imposed by the Government. |
| 64 | Providing and plastering of 15mm Cement plaster in cement mortar 1:5 (one cement isto five sand) on surface of brick/ concrete/ stone walls including forming groove of uniform size from 12x12 mm (twelve into twelve millimetre) and upto 25x15 mm (twenty five into fifteen millimetre) in the top layer of plastered surface as per approved design & pattern having 230mm c/c (two hundered thirty millimetre centre to centre) horizontally equal wideness and finishing of groove complete as per architectural drawings including carriage of material within all leads, lifts and other incidentals, as per approved specifications drawing, design and as directed by the Engineer-in-charge. The rate is inclusive of octroi, royality, Malkhana, Toll tax, sale tax, GST and any other taxes imposed by the Government. |
| 65 | Providing and plastring 20mm (Twenty millimetre) thick Pattern in cement Plaster with cement Mortar 1:4 (One cement isto Four coarse sand) In Single Coat on the fair side of brick Concrete Stone walls for Interior plastising making a uniform 150+28+150) (one hundred fiftyplus twenty plus one hundred fifty millimeter band and creating a 20mm (Twenty millimeter) Horizontal groove between two band upto all floor levelling meluding asises, Internd rounded angle chamfers and or arounded angle in all girth and finished even smooth complete as per architectural drawings including carriage of material within all leads, lifts and other incidentals, as per approved specifications drawing, design and as directed by the Engineer-in-charge. The rate is inclusive of octroi, royality, Malkhana, Toll tax, sale tax, GST and any other taxes imposed by the Government. |
| 66 | Providing and laying 600x 600mm (Six hundered into six hundered millimetre), 10mm (ten millimetre thick) Double Charge / Ultra Charge vetrified tiles of Kajaria / NITCO / Somany / Simpolo/ Johnson with water absorption less than 0.08% (zero decimal zero eight percent) and conforming to IS: 15622, of approved shade and design, in flooring laid on a bed of 20mm (twenty millimetre) thick cement mortar 1:4 (One cement isto four sand) laid over and jointed with neat cement slurry finished with flush pointing in white cement mixed with pigment of required shade to match the shade of tiles complete as per architectural drawings including carriage of material within all leads, lifts and other incidentals, as per approved specifications, design and as directed by the Engineer-In-Charge. The rate is inclusive of octroi, royality, Malkhana, Toll tax, GST and any other taxes imposed by the Government. |
| 67 | Providing and laying (600x600x10)mm (Six hundered into Six hundered into ten millimetres) full body /full body anti skid vitrified tile with water absorption less than 0.5% (Zero point five percent) and conforming to IS: 15622 of approved makeNitco /Kajaria / Simpolo /Johnson / Somany/Orient & bell/ AGL/ RAK/ Restile in all colours and shades in flooring or other similar location etc., laid on 20mm (twenty millimetre) thick base of cement mortar 1:4 (One cement isto four coarse sand) in all shapes & patterns including grouting the joints with white cement mixed with matching pigments etcetera complete in all respect including carriage of material within all leads, lifts and other incidentals, as per approved specifications, drawing, design and as directed by the Engineer-in-charge. The rate is inclusive of octroi, royality, Malkhana, Toll tax, sale tax, GST and any other taxes imposed by the Government. |
| 68 | Providing and laying 600x 600mm (Six hundered into six hundered millimetre), 10mm (ten millimetre thick)Double Charge / Ultra Charge Vitrified tiles of Kajaria / NITCO / Somany / Simpolo/ Johnson as per approved shade and design, with water absorption less than 0.08% (Zero point zero eight percent) and conforming to I.S. 15622, of approved make, in all colours & shade, in skirting, riser of steps, over 12 mm (Twelve millimetre) thick bed of cement mortar 1:3 (One cement isto Three coarse sand), jointing with grey cement slurry @ 3.3 Per Kilogram/ Per square metre (Three point three kilogram Per square metre) including grouting the joint with white cement & matching pigments etcetera complete as per architectural drawings including carriage of material within all leads, lifts and other incidentals, as per approved specifications, design and as directed by the Engineer-In-Charge. The rate is inclusive of octroi, royality, Malkhana, Toll tax, GST and any other taxes imposed by the Government. |
| 69 | Providing and laying (600x600x10)mm (Six hundered into Six hundered into ten millimetres) full body /full body anti skid vitrified tile of Nitco /Kajaria / Simpolo /Johnson / Somany/Orient & bell/ AGL/ RAK/ Restile as per approved shade and design of the office and thickness to be specified by manufacturer), with water absorption less than 0.08% (Zero point zero eight percent) and conforming to I.S. 15622, of approved make, in all colours & shade, in skirting, riser of steps, over 12mm (Twelve millimetre) thick bed of cement mortar 1:3 (One cement isto Three coarse sand) jointing with grey cement slurry @ 3.3 Kilogram/ Square metre (Three point three kilogram per suare metre) including grouting the joint with white cement and matching pigments etcetera complete as per architectural drawings including carriage of material within all leads, lifts and other incidentals, as per approved specifications, drawing, design and as directed by the Engineer-in-charge. The rate is inclusive of octroi, royality, Malkhana, Toll tax, sale tax, GST and any other taxes imposed by the Government. |
| 70 | Providing and laying 300x300 mm (Three hundered into Three hundered millimetre) with 10mm (ten millimetre) thickness of premium quality antiskid ceramic floor tiles ofNitco /Kajaria / Simpolo /Johnson / Somany/Orient & bell/ AGL/ RAK/ Restile/Orient & bell/ AGL/ RAK/ Restile conforming to IS : 15622 of approved shade and design, laid on a bed of 20mm (twenty millimetre) thick cement mortar 1:4 (One cement isto four sand) laid over and jointed with neat cement slurry finished with flush pointing in white cement mixed with pigment of required shade to match the shade of tiles complete as per architectural drawings including carriage of material within all leads, lifts and other incidentals, as per approved specifications, drawing, design and as directed by the Engineer-in-charge. The rate is inclusive of octroi, royality, Malkhana, Toll tax, sale tax, GST and any other taxes imposed by the Government. |
| 71 | Providing and laying 300x450mm (Three hundered into four hundered fifty millimetres) into 10mm (ten millimetre) thick Ceramic Glazed tiles of Nitco /Kajaria / Simpolo /Johnson / Somany/Orient & bell/ AGL/ RAK/ Restile in skirting risers of steps and dados with cement mortar 1:3 (One cement isto three sand) laid over and jointed with neat cement slurry finished with flush pointing in white cement mixed with pigment of required shade to match the shade of tiles complete, as per approved drawing, design, specifications and as per directions and entire satisfaction of the Engineer-In-Charge, including carriage of material within all leads, lifts and other incidentals. The rate is inclusive of octroi, royality, malkhana, Toll tax, GST and any other taxes imposed by the Government. |
| 72 | Providing and laying mirror polished 25mm (Twenty five millimetre) thick Kota stone minimum Size 55x55cm (Fifty five into Fifty five centimetre) of uniform colour with 15cm (Fifteen centimetre) wide Jaisalmer Yellow marble band of same shade that of flooring of approved shade as per detail slab flooring over 20 mm (twenty millimetre) thick base laid over and jointed with grey cement slurry mixed with pigment to match the shade of the slab, including rubbing and polishing complete with base of cement mortar 1:4 (One cement isto Four coarse sand) complete as per architectural drawings including carriage of material within all leads, lifts and other incidentals, as per approved specifications, design and as directed by the Engineer-in-charge. The rate is inclusive of octroi, royality, Malkhana, Toll tax, GST and any other taxes imposed by the Government. |
| 73 | Providing and laying Kota stone slabs 25mm (Twenty five millimetre) thick in risers of steps, skirting, dado and pillars laid on 12mm (Twelve millimetre) thick cement mortar 1:3 (One cement isto Three coarse sand) and jointed with grey cement slurry mixed with pigment to match the shade of the slabs, including rubbing and polishing complete as per architectural drawings including carriage of material within all leads, lifts and other incidentals, as per approved specifications, design and as directed by the Engineer-in-charge. The rate is inclusive of octroi, royality, Malkhana, Toll tax, GST and any other taxes imposed by the Government. |
| 74 | Providing and laying 300x300x25 mm (Three hundered into three hundered into twenty five millimetres) Labrador Design ( Rainbow Series) tiles of NTC / Unistone / Atlantic in flooring in ramp for person with disability on 20mm (Twenty millimetres) average thick base of cement mortar 1:4 (One cement isto four sand) laid over and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and granite polish finish complete as per architectural drawings including carriage of material within all leads, lifts and other incidentals, as per approved specifications drawing, design and as directed by the Engineer-In-Charge. The rate is inclusive of octroi, royality, Malkana, Toll tax, sale tax, GST and any other taxes imposed by the Government. |
| 75 | Providing and laying 60mm (sixty millimetre) thick faciory made cement concrete interlocking paver block of M-40 M-forty) grade made by block making machine with strong vibratory compaction, of approved size, design & shape, laid in required colour and pattern over and including 50mm (fifty millimetre) thick compacted bed of coarse sand, filling the joints with fine sand etcetera all complete including carriage of material within all leads, lifts and other incidentals, as per approved specifications drawing, design and as directed by the Engineer-In-Charge. The rate is inclusive of octroi, royality, Malkana, Toll tax, GST and any other taxes imposed by the Government. |
| 76 | Providing and applying distempering with oil bound washable distemper of Nerolac/ Asian Paints to give an even shade : New work (two or more coats) over and including water thinnable priming coat with cement primer Priming coat with distemper primer complete including carriage of material within all leads, lifts and other incidentals, as per approved specifications drawing, design and as directed by the Engineer-In-Charge. The rate is inclusive of octroi, royality, Malkana, Toll tax, sale tax, GST and any other taxes imposed by the Government. |
| 77 | Providing and applying Birla / J.K. white wall care putty over plaster surface after thoroughly brushing the surface free from mortar dropings, dust, loose material and other foreign matters, sand papered smooth to give final matt finish to the surface upto floor all level complete including carriage of material within all leads, lifts and other incidentals, as per specifications, approved drawing, design and as directed by the Engineer-In-Charge. The rate is inclusive of octroi, royality, Malkhana, Toll tax, GST and any other taxes imposed by the Government. |
| 78 | Providing and painting Wall painting (two coats) with Premium acrylic emulsion of Asian Paints/ Dulux /Berger paints/Nerolac Suraksha paints for interior grade on undecorated concrete/stone/plastered wall surfaces to give an even shade including thoroughly brushing the surface free from mortar dropping and other foreign matter and sand papered smooth including applying of putty as required for matting the surface smooth complete as per architectural drawings including carriage of material within all leads, lifts and other incidentals, as per approved specifications drawing, design and as directed by the Engineer-In-Charge. The rate is inclusive of octroi, royality, Malkhana, Toll tax, GST and any other taxes imposed by the Government. |
| 79 | Providing and painting two coats with silicon & acrylic emulsion of Asian Paints/ Dulux /Berger paints/Nerolac Suraksha paints for interior grade on undecorated concrete/stone/plastered wall surfaces to give an even shade including thoroughly brushing the surface free from mortar dropping and other foreign matter and sand papered smooth including applying of putty as required for matting the surface smooth complete as per architectural drawings including carriage of material within all leads, lifts and other incidentals, as per approved specifications, drawing, design and as directed by the Engineer-In-Charge. The rate is inclusive of octroi, royality, Malkhana, Toll tax, GST and any other taxes imposed by the Government. |
| 80 | Providing and painting walls with weather proof exterior emulsion of Asian Paints/ Dulux /Berger paints/Nerolac Suraksha paints of approved shade having VOC less than 50 gm/litre (Fifty gram per litre) and UV resistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance exterior paint of required shade with silicon additives New work (Two or more coats applied @ 1.43 litre/ 10 Square metre (One point forty three litre per ten square metre) over and including priming coat of exterior primer applied @ 0.90 litre/10 Square metre (Zero point ninety litre per ten square metre) upto all floor level complete as per architectural drawings including carriage of material within all leads, lifts and other incidentals, as per approved specifications, drawing, design and as directed by the Engineer-In-Charge. The rate is inclusive of octroi, royality, Malkhana, Toll tax, GST and any other taxes imposed by the Government. |
| 81 | Providing & finishing surface with Epoxy paint (two or more coats) on steel work at all locations prepared and applied as per manufacturer's specifications including preparation of surface, etcetera complete as per approved brand Asian Paints/ Dulux /Berger paints/Nerolac Suraksha paints complete as per architectural drawings including carriage of material within all leads, lifts and other incidentals, as per approved specifications, drawing, design and as directed by the Engineer-In-Charge. The rate is inclusive of octroi, royality, Malkhana, Toll tax, GST and any other taxes imposed by the Government. |
| 82 | Providing and painting with oil type wood preservative of (Asian Paints/ Dulux /Berger paints/Nerolac Suraksha paints) for new wood work by applying two or more coats, including preparing the surface by thoroughly cleaning oil, grease, dirt and other foreign matter, sand papering and knotting etcetera complete including carriage of material within all leads, lifts and other incidentals, as per approved specifications drawing, design and as directed by the Engineer-In-Charge. The rate is inclusive of octroi, royality, Malkana, Toll tax, GST and any other taxes imposed by the Government. |
| 83 | Providing and applying priming coat over new wood and wood based surfaces after and including preparing the surface by thoroughly cleaning oil, grease, dirt and other foreign matters sand papering and knotting of readymixed paint brushing with white lead for priming of Asian paints, ICI Asian Paints/ Dulux /Berger paints/Nerolac Suraksha paints complete including carriage of material within all leads, lifts and other incidentals, as per approved specifications drawing, design and as directed by the Engineer-In-Charge. The rate is inclusive of octroi, royality, Malkana, Toll tax, GST and any other taxes imposed by the Government. |
| 84 | Providing and painting two coats (excluding priming coat) on new wood and wood based surface with enamel paint of Asian paints, ICI Asian Paints/ Dulux /Berger paints/Nerolac Suraksha paints to give an even shade including cleaning the surface of dirt, dust and other foreign matter, sand papering & stopping including carriage of material within all leads, lifts and other incidentals, as per approved specifications, drawing, design and as directed by the Engineer-In-Charge. The rate is inclusive of octroi, royality, Malkhana, Toll tax, GST and any other taxes imposed by the Government. |
| 85 | Providing and laying Damp Proof Course 50mm (fifty millimetre) thick with cement concrete 1:2:4 (one cement isto two sand isto four graded/crushed stone aggregate) 20mm (Twenty millimetre nominal size) and curing complete, as required at site including carriage of material within all leads, lifts and other incidentals, as per approved specifications, drawing, design and as directed by the Engineer-In-Charge. The rate is inclusive of octroi, royality, Malkana, Toll tax, GST and any other taxes imposed by the Government. |
| 86 | Providing & applying a coat of residual petroleum bitumen of grade of VG-10 (Viscosity grade-Ten) of approved quality using 1.7 Kilogram/Square metre (One point seven kilogram per square metre) on damp proof course after cleaning the surface with brushes and finally with apiece of cloth lightly soaked in kerosene oil etcetera complete including carriage of material within all leads, lifts and other incidentals, as per approved specifications, drawing, design and as directed by the Engineer-In-Charge. The rate is inclusive of octroi, royality, Malkhana, Toll tax, GST and any other taxes imposed by the Government. |
| 87 | Providing and laying water proofing treatment to vertical and horizontal surfaces of depressed portions of W.C., kitchen and the like consisting of:i) Ist course of applying cement slurry @ 4.4 (four point four) Kilogram/Square metre mixed with water proofing compound conforming to IS 2645 in recommended proportions including rounding off junction of vertical and horizontal surface.ii) IInd course of 20 mm cement plaster 1:3 (One cement isto three coarse sand) mixedwith water proofing compound in recommended proportion including rounding off junction of vertical and horizontal surface.iii) IIIrd course of applying blown or residual bitumen applied hot at 1.7 (one point seven) Kilogram.per Square metre of area.iv) IVth course of 400 (four hundered) micron thick PVC sheet. (Overlaps at joints of PVC sheet should be 100mm (one hundered millimetre) wide and pasted to Each other with bitumen @ 1.7 (one point seven) Kilogram/Square metre. complete as per architectural drawings including carriage of material within all leads, lifts and other incidentals, as per approved specifications, drawing, design and as directed by the Engineer-In-Charge. The rate is inclusive of octroi, royality, Malkhana, Toll tax, GST and any other taxes imposed by the Government. |
| 88 | Providing and laying Dr. Fixit Torch Shield (P-3160-3mm), APP (Atactic Polypropylene Polymer) modified prefabricated five layer, 3 mm (three millimetre) thick water proofing membrane, black finished reinforced with glass fibre matt consisting of a coat of bitumen primer for bitumen membrane @ 0.40 litre/Per Square Metre (at the rate zero point fourty litre per square metre) by the same membrane manufactured of density at 25°C, 0.87 - 0.89 Per Kilogram/litre and viscocity 70 - 160 cps. Over the primer coat the layer of membrane shall be laid using butane torch and sealing all joints etcetera, and preparing the surface complete. The vital physical and chemical parameters of the membrane shall be as under : Joint strength in longitudinal and transverse direction at 23°C as 350/300 N/ 5cm (five centimetre) . Tear strength in longitudinal and transverse direction as 60/80N. Softening point of membrane not less than 150°C. Cold flexibility shall be upto -2°C when tested in accordance with ASTM,D -5147. The laying of membrane shall be got done through the authorised applicator of the manufacturer of membrane including carriage of material within all leads, lifts and other incidentals as per approved specifications, drawing, design and as directed by the Engineer-In-Charge. The rate is inclusive of octroi, royality, Malkana, Toll tax, GST and any other taxes imposed by the Government. |
| 89 | Providing and fixing 25mm (twenty five millimetre) thick Commercial Board waterproof termite resistant shutters for cup boards including fixing with SS 304 grade hinges with screws etcetera and finished with 25x6mm (twenty five into six millimetre) hard wood lipping / edging complete of Nova pan / Kit ply / National / Archidply / Action Tesa / Green Ply including carriage of material within all leads, lifts and other incidentals as per approved specifications, drawing, design and as directed by the Engineer-In-Charge. The rate is inclusive of octroi, royality, Malkana, Toll tax, GST and any other taxes imposed by the Government. |
| 90 | Providing and fixing 19mm (Nineteen millimetre) thick water proof termite resistant commercial board in shelves/box for cup board with butt joints & fixing with nails & screws etcetera complete of Nova pan / Kit ply / National / Archidply / Action Tesa / Green Ply including carriage of material within all leads, lifts and other incidentals as per approved specifications, drawing, design and as directed by the Engineer-in-charge. The rate is inclusive of octroi, royality, Malkana, Toll tax, GST and any other taxes imposed by the Government. |
| 91 | Providing and fixing 1.00mm (one millimetre) thick colored & decorative high pressure laminated sheet of plain / wood grain in gloss / matt/ suede finish with high density protective surface layer and reverse side of adhesive bonding quality conforming to IS : 2046 Type S, including cost of adhesive of approved quality including carriage of material within all leads, lifts and other incidentals as per approved specifications, drawing, design and as directed by the Engineer-In-Charge. The rate is inclusive of octroi, royality, Malkana, Toll tax, GST and any other taxes imposed by the Government. |
| 92 | Providing and fixing 250x16mm (Two hundered fifty into Sixteen millimetres) nominal size bright/matt finished Stainless steel sliding door bolts ISI marked or approved quality & make with necessary screws etcetera complete including carriage of material within all leads, lifts and other incidentals and as per specifications, approved drawing, design and as directed by the Engineer-In-Charge. The rate is inclusive of octroi, royality, Malkana, Toll tax, GST and any other taxes imposed by the Government. |
| 93 | Providing and fixing 100x10mm (One hundered into Ten millimetres) nominal size bright/matt finished Stainless steel Tower bolts (barrel type), ISI marked or approved quality & make with necessary screws etcetera complete including carriage of material within all leads, lifts and other incidentals and as per specifications, approved drawing, design and as directed by the Engineer-In-Charge. The rate is inclusive of octroi, royality, Malkana, Toll tax, GST and any other taxes imposed by the Government. |
| 94 | Providing and fixing 300x16mm (Three hundered into Sixteen millimetres) nominal size aluminium sliding door bolts ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour or shade, with nuts and screws etcetera complete, including carriage of material within all leads, lifts and other incidentals and as per specifications, approved drawing, design and as directed by the Engineer-In-Charge. The rate is inclusive of octroi, royality, Malkhana, Toll tax, GST and any other taxes imposed by the Government. |
| 95 | Providing and fixing 250x16mm (two hundered fifty into Sixteen millimetres) nominal size aluminium sliding door bolts ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour or shade, with nuts and screws etcetera complete, including carriage of material within all leads, lifts and other incidentals and as per specifications, approved drawing, design and as directed by the Engineer-In-Charge. The rate is inclusive of octroi, royality, Malkhana, Toll tax, GST and any other taxes imposed by the Government. |
| 96 | Providing and fixing aluminium 200x10mm (two hundered into Ten millimetres) nominal size Tower bolts, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour or shade, with nuts and screws etcetera. complete, including carriage of material within all leads, lifts and other incidentals and as per specifications, approved drawing, design and as directed by the Engineer-In-Charge. The rate is inclusive of octroi, royality, Malkhana, Toll tax, GST and any other taxes imposed by the Government. |
| 97 | Providing and fixing aluminium 150x10mm (One hundered fifty into Ten millimetres) nominal size Tower bolts, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour or shade, with nuts and screws etcetera. complete, including carriage of material within all leads, lifts and other incidentals and as per specifications, approved drawing, design and as directed by the Engineer-In-Charge. The rate is inclusive of octroi, royality, Malkhana, Toll tax, GST and any other taxes imposed by the Government. |
| 98 | Providing and fixing 150x10mm (One hundered fifty into Ten millimetres) nominal size oxidised M.S. tower bolt black finish, (Barrel type) with necessary screws complete, including carriage of material within all leads, lifts and other incidentals and as per specifications, approved drawing, design and as directed by the Engineer-In-Charge. The rate is inclusive of octroi, royality, Malkhana, Toll tax, GST and any other taxes imposed by the Government. |
| 99 | Providing and fixing 100x10mm (One hundered into Ten millimetres) nominal size oxidised M.S. tower bolt black finish, (Barrel type) with necessary screws complete, including carriage of material within all leads, lifts and other incidentals and as per specifications, approved drawing, design and as directed by the Engineer-In-Charge. The rate is inclusive of octroi, royality, Malkhana, Toll tax, GST and any other taxes imposed by the Government. |
| 100 | Providing and fixing bright finished brass 100 mm (one hundered millimetre) mortice latch and lock with 6 (six) levers and a pair of lever handles of approved quality with necessary screws complete, including carriage of material within all leads, lifts and other incidentals and as per specifications, approved drawing, design and as directed by the Engineer-In-Charge. The rate is inclusive of octroi, royality, Malkhana, Toll tax, sale tax, GST and any other taxes imposed by the Government. |
| 101 | Providing and fixing 65x35mm (Sixty five into Thirty five millimetres) size special quality chromium plated brass cup board lock with six levers including necessary screws etcetera complete (Indian make approved quality) including carriage of material within all leads, lifts and other incidentals and further as per specifications, approved drawing, design and as directed by the Engineer-In-Charge. The rate is inclusive of octroi, royality, Malkana, Toll tax, GST and any other taxes imposed by the Government. |
| 102 | Providing and fixing 125x34x24 mm (one hundered twenty five into thirty four into twnety four millimetre) weighing not less than 23 gms (twenty three grams) of bright finished PTMT handles with screws complete as per architectural drawings specifications, design and as per the directions of Engineer-In-Charge including carriage of material within all leads, lifts and other incidentals. The rate is inclusive of octroi, royality, Malkana, Toll tax, sale tax, GST and any other taxes imposed by the Government. |
| 103 | Providing and fixing bright /matt finished Stainless Steel 304 Grade 125mm (one hundered twenty five millimetre of approved quality & make with necessary screws etcetera complete including carriage of material within all leads, lifts and other incidentals and as per specifications, approved drawing, design and as directed by the Engineer-In-Charge. The rate is inclusive of octroi, royality, Malkana, Toll tax, GST and any other taxes imposed by the Government. |
| 104 | Providing and fixing 100mm (One hundered millimetres) nominal size aluminium Handles ISI marked anodised (anodic coating not less than grade AC 10 as per IS: 1868) transparent or dyed to required colour or shade with necessary screws etcetera; complete including carriage of material within all leads, lifts and other incidentals and as per specifications, approved drawing, design and as directed by the Engineer-In-Charge. The rate is inclusive of octroi, royality, Malkhana, Toll tax, GST and any other taxes imposed by the Government. |
| 105 | Providing and fixing 125mm (One hundered twenty five millimetres) nominal size M.S. Handles ISI marked with necessary screws etcetera; complete including carriage of material within all leads, lifts and other incidentals and as per specifications, approved drawing, design and as directed by the Engineer-In-Charge. The rate is inclusive of octroi, royality, Malkhana, Toll tax, GST and any other taxes imposed by the Government. |
| 106 | Providing and fixing 100mm (One hundered millimetres) nominal size M.S. Handles ISI marked with necessary screws etcetera; complete including carriage of material within all leads, lifts and other incidentals and as per specifications, approved drawing, design and as directed by the Engineer-In-Charge. The rate is inclusive of octroi, royality, Malkhana, Toll tax, GST and any other taxes imposed by the Government. |
| 107 | Providing and fixing aluminium hanging floor Twin door stopper, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour and shade, with necessary screws etcetera; complete including carriage of material within all leads, lifts and other. incidentals and further as per specifications, approved drawing, design and as directed by the Engineer-In-Charge. The rate is inclusive of octroi, royality, Malkana, Toll tax, GST and any other taxes imposed by the Government. |
| 108 | Providing and fixing aluminium hanging floor Single door stopper, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour and shade, with necessary screws etcetera; complete including carriage of material within all leads, lifts and other. incidentals and further as per specifications, approved drawing, design and as directed by the Engineer-In-Charge. The rate is inclusive of octroi, royality, Malkana, Toll tax, GST and any other taxes imposed by the Government. |
| 109 | Providing and fixing 250mm (two hundered fifty millimetres) nominal size aluminium casement stays, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour or shade, with nuts and screws etcetera complete, including carriage of material within all leads, lifts and other incidentals and as per specifications, approved drawing, design and as directed by the Engineer-In-Charge. The rate is inclusive of octroi, royality, Malkhana, Toll tax, GST and any other taxes imposed by the Government. |
| 110 | Providing and fixing 200mm (two hundered millimetres) nominal size aluminium casement stays, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour or shade, with nuts and screws etcetera complete, including carriage of material within all leads, lifts and other incidentals and as per specifications, approved drawing, design and as directed by the Engineer-In-Charge. The rate is inclusive of octroi, royality, Malkhana, Toll tax, GST and any other taxes imposed by the Government. |
| 111 | Providing and fixing double action hydraulic floor spring of approved brand and manufacture conforming to IS : 6315, having brand logo embossed on the body / plate with double spring mechanism and door weight upto 125 Per Kilogram (one hundered twenty five kilogram), for doors, including cost of cutting floors, embedding in floors as required and making good the same matching to the existing floor finishing and cover plates with brass pivot and single piece M.S. sheet outer box with slide plate etcetera complete, including carriage of material within all leads, lifts and other incidentals and as per specifications, approved drawing, design and as directed by the Engineer-In-Charge. The rate is inclusive of octroi, royality, Malkhana, Toll tax, GST and any other taxes imposed by the Government. |
| 112 | Providing and fixing aluminium extruded section body tubular type universal hydraulic door closer (having brand logo with ISI, IS : 3564, embossed on the body, door weight upto 36 Per Kilogram to 80 Per Kilogram (thirty six kilogram to eighty kilogram) and door width from 701 mm to 1000 mm (seven hundered one millimetre to one thousand millimetre), with double speed adjustment with necessary accessories and screws etcetera complete, including carriage of material within all leads, lifts and other incidentals and as per specifications, approved drawing, design and as directed by the Engineer-In-Charge. The rate is inclusive of octroi, royality, Malkhana, Toll tax, GST and any other taxes imposed by the Government. |
| 113 | Providing and fixing 150mm (One hundered fifty millimetres) diametre on wall face PVC rain water pipes of working pressure 4/6 Per Kilogram/cm2 (Four/six kilograms/per centimeters square) ISI marked of Finolex / Vectus including filling the joints with approved adhesive complete as per architectural drawings including carriage of material within all leads, lifts and other incidentals, as per approved specifications drawing, design and as directed by the Engineer-In-Charge. The rate is inclusive of octroi, royality, Malkana, Toll tax, GST and any other taxes imposed by the Government. |
| 114 | Providing and fixing 150mm (One hundered fifty millimetres) nominal bore/diameter Plain bend ISI marked of Finolex / Vectus including fixing with approved adhesive complete. including carriage of material within all leads, lifts and other incidentals, as per approved specifications drawing, design and as directed by the Engineer-In-Charge. The rate is inclusive of octroi, royality, Malkana, Toll tax, GST and any other taxes imposed by the Government. |
| 115 | Providing and fixing 150mm (One hundered fifty millimetres) diametre Shoe on wall face PVC rain water pipes working pressure 4/6 K.g/cm2 (Four/six kilogram/per centimetres square) ISI marked of Finolex / /Vectus including priming coat, painting and welding etcetera complete as per architectural drawings including carriage of material within all leads, lifts and other incidentals, as per approved specifications drawing, design and as directed by the Engineer-In-Charge. The rate is inclusive of octroi, royality, Malkana, Toll tax, GST and any other taxes imposed by the Government. |
| 116 | Providing and fixing 150mm (One hundered fifty millimetre) diametre PVC clamps ISI marked of Finolex / Vectus approved design to PVC rain water pipe including cost of cutting holes and steel screws, rawal plug and making good the walls etcetera complete as per architectural drawings including carriage of material within all leads, lifts and other incidentals, as per approved specifications drawing, design and as directed by the Engineer-In-Charge. The rate is inclusive of octroi, royality, Malkana, Toll tax, GST and any other taxes imposed by the Government. |
| 117 | Water Supply & Sanitary Installations Making connection of galvanized mild steel distribution branch with galvanized mild steel main 20mm to 40mm (Twenty milimetres to Forty milimetres) nominal bore by providing and fixing tees including cutting and threading the pipe complete as per architectural drawings including carriage of material within all leads, lifts and other incidentals, as per approved specifications drawing, design and as directed by the Engineer-In-Charge. The rate is inclusive of octroi, royality, Malkana, Toll tax, GST and any other taxes imposed by the Government. |
| 118 | Providing and fixing 110mm (One hundered ten millimetre) nominal bore/diameter High pressure PVC Spigot and Socket, waste and ventilating pipe 4.00 to 4.6 mm (Four point zero to four point six millimetre) thick of ISI marked of Finolex / Vectus including fixing with approved adhesive etcetera complete as per architectural drawings including carriage of material within all leads, lifts and other incidentals, as per approved specifications drawing, design and as directed by the Engineer-In-Charge. The rate is inclusive of octroi, royality, Malkana, Toll tax, GST and any other taxes imposed by the Government. |
| 119 | Providing and fixing 150mm (One hundered fifty millimetre) nominal bore/diameter High pressure PVC Spigot and Socket, waste and ventilating pipe 4.00 to 4.6 mm (Four point zero to four point six millimetre) thick of ISI marked of Finolex / Vectus including fixing with approved adhesive etcetera complete as per architectural drawings including carriage of material within all leads, lifts and other incidentals, as per approved specifications drawing, design and as directed by the Engineer-In-Charge. The rate is inclusive of octroi, royality, Malkana, Toll tax, GST and any other taxes imposed by the Government. |
| 120 | Providing and fixing 75mm (Seventy five millimetre) nominal bore/diameter High pressure PVC Spigot and Socket, waste and ventilating pipe 4.00 to 4.6 mm (Four point zero to four point six millimetre) thick of ISI marked of Finolex / Vectus including fixing with approved adhesive etcetera complete as per architectural drawings including carriage of material within all leads, lifts and other incidentals, as per approved specifications drawing, design and as directed by the Engineer-In-Charge. The rate is inclusive of octroi, royality, Malkana, Toll tax, GST and any other taxes imposed by the Government. |
| 121 | Providing and fixing 110mm (One hundered ten millimetres) diametre Plain bend on wall face PVC rain water pipes working pressure 4/6 K.g/cm2 (Four/six kilogram/per centimetres square) ISI marked of Finolex / Vectus including priming coat, painting and welding etcetera complete as per architectural drawings including carriage of material within all leads, lifts and other incidentals, as per approved specifications drawing, design and as directed by the Engineer-In-Charge. The rate is inclusive of octroi, royality, Malkana, Toll tax, GST and any other taxes imposed by the Government. |
| 122 | Providing and fixing 75mm (Seventy five millimetre) nominal bore/diameter Plain bend ISI marked of Finolex / Vectus including fixing with approved adhesive complete. including carriage of material within all leads, lifts and other incidentals, as per approved specifications drawing, design and as directed by the Engineer-In-Charge. The rate is inclusive of octroi, royality, Malkana, Toll tax, GST and any other taxes imposed by the Government. |
| 123 | Providing and fixing 110mm (One hundered ten millimetre) diametre P.V.C door bend with oval access door, of Finolex / Vectus insertion rubber washer 3mm (Three millimeter) thick bolts and nuts ISI marked including finishing with approved adhesive complete including carriage of material within all leads, lifts and other incidentals as per specifications, approved drawing, design and as directed by the Engineer-In-Charge. The rate is inclusive of octroi, royality, Malkana, Toll tax, GST and any other taxes imposed by the Government. |
| 124 | Providing and fixing 110x75mm (One hundered into seventy five millimetre) nominal size ISI marked P.V.C floor trap of Finolex / Vectus of self cleaning design complete including fixing with approved adhesive cost of cutting and making good the walls and floors etcetera complete as per architectural drawings including carriage of material within all leads, lifts and other incidentals, as per approved specifications drawing, design and as directed by the Engineer-In-Charge. The rate is inclusive of octroi, royality, Malkana, Toll tax, GST and any other taxes imposed by the Government. |
| 125 | Providing and fixing 110mm (One hundered ten millimetre) nominal bore/diameter ISI marked PVC collar of Finolex / Vectus complete upto all floor level complete as per architectural drawings including carriage of material within all leads, lifts and other incidentals, as per approved specifications drawing, design and as directed by the Engineer-In-Charge. The rate is inclusive of octroi, royality, Malkana, Toll tax, GST and any other taxes imposed by the Government. |
| 126 | Providing and fixing 75mm (Seventy five millimetre) nominal bore/diameter P.V.C cowl of Finolex / Vectus ISI marked including finishing with approved design with steel screws and rawal plugs etcetera complete as per architectural drawings including carriage of material within all leads, lifts and other incidentals, as per approved specifications drawing, design and as directed by the Engineer-In-Charge. The rate is inclusive of octroi, royality, Malkana, Toll tax, GST and any other taxes imposed by the Government. |
| 127 | Providing and fixing 90mm (Ninety millimetre) nominal bore/diameter P.V.C cowl of Finolex / Vectus ISI marked for waste and ventilating pipes including finishing with approved design with steel screws and rawal plugs etcetera. complete as per architectural drawings including carriage of material within all leads, lifts and other incidentals, as per approved specifications drawing, design and as directed by the Engineer-In-Charge. The rate is inclusive of octroi, royality, Malkana, Toll tax, GST and any other taxes imposed by the Government. |
| 128 | Providing and fixing 110mm (One hundered ten millimetre) nominal bore/diameter P.V.C cowl of Finolex / Vectus ISI marked for waste and ventilating pipes including finishing with approved design with steel screws and rawal plugs etcetera. complete as per architectural drawings including carriage of material within all leads, lifts and other incidentals, as per approved specifications drawing, design and as directed by the Engineer-In-Charge. The rate is inclusive of octroi, royality, Malkana, Toll tax, GST and any other taxes imposed by the Government. |
| 129 | Providing and fixing square-mouth S.W. gully trap class SP-1 complete with C.I. grating brick masonry chamber with water tight C.I. cover with frame of 300 x300 mm (three hundered into three hundered millimetre) size (inside) the weight of cover to be not less than 4.50 (four point five)Per Kilogram and frame to be not less than 2.70 Per Kilogram (two point seven zero kilogram)as per standard design: 100x100 mm (one hundered into one hundered millimetre) size P type, with common burnt clay F.P.S. (non modular) bricks of class designation 7.5. complete as per architectural drawings including carriage of material within all leads, lifts and other incidentals, as per approved specifications drawing, design and as directed by the Engineer-In-Charge. The rate is inclusive of octroi, royality, Malkana, Toll tax, GST and any other taxes imposed by the Government. |
| 130 | Providing and fixing white vitreous china flat back single half stall urinal Large flat back no 60002 of size 39x37.5x59cm (Thirty nine into thirty seven point five into fifty nine centimentre) with white PVC automatic flushing cistern of Hindware/ Cera/ Jaquar of star white / Snow white shade and as shown in the drawing / as per details with ittings, standard size C.P. brass flush pipe, spreaders with unions and clamps (all in C.P. brass) with waste fitting as per IS : 2556, C.I. trap with outlet grating and other couplings in C.P. brass, including painting of fittings and cutting and making good the walls and floors wherever required with 10 (Ten) litre P.V.C. automatic flushing cistern including necessary fitting complete including carriage of material within all leads, lifts and other incidentals as per specifications, approved drawing, design and as directed by the Engineer-in-charge. The rate is inclusive of octroi, royality, Malkhana, Toll tax, sale tax, GST and any other taxes imposed by the Government. |
| 131 | Providing and fixing 300 x 600mm (Three hundered into Six Hundered millimetre) vitreous china division plate for urinals of Hindware/cera/Jaquar of star white / snow white shade complete including carriage of material within all leads, lifts and other incidentals as per specifications, approved drawing, design and as directed by the Engineer-In-Charge. The rate is inclusive of octroi, royality, Malkana, Toll tax, GST and any other taxes imposed by the Government. |
| 132 | Providing and fixing white vitreous china pedestal type water closet (European type) No 20087 (S - 10 ) Size 57x 35x39cm (Fifty seven into thirty five into thirty nine millimetre) nominal size with seat and lid, 10 litre (Ten) low level white PVC flushing cistern (sleek Plus) having dual flush system of Hindware/ Cera/ Jaquar of star white / Snow white shade and as shown in the drawing / as per details & C.P. flush bend with fittings and C.I. brackets, 40 mm (Forty millimetre) flush bend 20mm (Twenty millimetre) over flow pipe with seat & lid fixed with C.P. brass hinges and rubber buffers,with specials of standard make and mosquito proof coupling of approved municipal design complete including painting of fittings and brackets, cutting and making good the walls and and fixed with jet pressure and intergal P or S trap including jointing the trap and soil pipe with adhesive of approved brand. (Jet Spray to be measured and paid for separately) complete as per architectural drawings including carriage of material within all leads, lifts and other incidentals, as per approved specifications drawing, design and as directed by the Engineer-in-charge. The rate is inclusive of octroi, royality, Malkhana, Toll tax, sale tax, GST and any other taxes imposed by the Government. |
| 133 | Providing and fixing vitreous china pedestal type/wash down floor mounted Matrix water closet (WC) for specially abled person Cat no. 7011 with size of (740x550x835)mm (Seven hundered forty into five hundered fifty into Eight hundered thirty five millimetre) with supporting arrangement, white colour studio set along with 8mm (eight millimetre) diametre C.P pre-installed jet arrangement, SEAT COVER, Flushing CISTERN 10ltr. (ten litre) capacity and twin flushing valves etc. complete in all respect, water closet (European Type - WC pan) with integral 'p' or 's' trap including jointing the trap with soil pipe in cement mortar 1:1 (one cement, one sand) (with cistern, seat cover and flush fitting) of approved make (Hindware/ Cera/ Jaguar Star white/ Snowhite), complete including carriage of material within all leads, lifts and other incidentals as per specifications, approved drawing, design and as directed by the Engineer-In-Charge. The rate is inclusive of octroi, royality, Malkana, Toll tax, GST and any other taxes imposed by the Government. |
| 134 | Providing and fixing Health faucet ABS with rubbit cleaning system, flexible tube upto 1.25 mtr (one point two five metre) long PVC Flexible tube & ABS wall hook to extended wall mounted type W.C. of quality and make Kingston / Gem / Parko / JAL, ESS / Jaquar / Seiko complete including carriage of material within all leads, lifts and other incidentals as per specifications, approved drawing, design and as directed by the Engineer-In-Charge. The rate is inclusive of octroi, royality, Malkana, Toll tax, GST and any other taxes imposed by the Government. |
| 135 | Providing and fixing wash basin White Vitreous China Flat back wash basin Delta No 10010 size 550x 400 mm (Five hundered fifty into four hundered millimetre) (Pedestal type wash Basin ) Hindware/ Cera/ Jaquar of star white / Snow white shade and as shown in the drawing / as per details with single 15 mm (Fifteen millimetre) C.P. brass pillar tap with C.I. brackets, 15 mm (Fifteen millimetre) C.P. brass pillar taps, 32 mm (Thirty two millimetre) C.P. brass waste of standard pattern, including painting of fittings and brackets, cutting and making good the walls wherever required including necessary fitting complete including carriage of material within all leads, lifts and other incidentals as per specifications, approved drawing, design and as directed by the Engineer-in-charge. The rate is inclusive of octroi, royality, Malkhana, Toll tax, sale tax, GST and any other taxes imposed by the Government. |
| 136 | Providing and fixing Stainless Steel kitchen sink with drain board of Diamond/Unik/ Preyag big size 610x510x200 mm (Six hundered ten into five hundered ten into two hundered millimetres) including C.P. waste with C.I. or M.S. brackets painted white including cutting holes in walls and making good the same complete including carriage of material within all leads, lifts and other incidentals as per specifications, approved drawing, design and as directed by the Engineer-in-charge. The rate is inclusive of octroi, royality, Malkhana, Toll tax, GST and any other taxes imposed by the Government. |
| 137 | Providing and fixing 15mm (Fifteen millimeters) diametre C.P. brass bib tap of conforming to IS:8931 of Jaquar / Hindware / Cera / Kerovite & Jal of approved quality (superior or heavy type) complete including carriage of material within all leads, lifts and other incidentals as per specifications, approved drawing, design and as directed by the Engineer-In-Charge. The rate is inclusive of octroi, royality, Malkana, Toll tax, GST and any other taxes imposed by the Government. |
| 138 | Providing and fixing 15 mm (Fifteen millimeters) nominal bore, C.P. brass long body bib cock of approved quality conforming to IS standards and weighing not less than 690 gms Jaquar / Hindware / Cera / Kerovite & Jal including carriage of material within all leads, lifts and other incidentals as per specifications, approved drawing, design and as directed by the Engineer-In-Charge. The rate is inclusive of octroi, royality, Malkana, Toll tax, GST and any other taxes imposed by the Government. |
| 139 | Providing and fixing 15mm (Fifteen millimeter) diametre C.P. brass stop cock (concealed) of standard design and of approved make conforming to IS:8931 Jaquar / Hindware / Cera / Kerovite & Jal including carriage of material within all leads, lifts and other incidentals as per specifications, approved drawing, design and as directed by the Engineer-In-Charge. The rate is inclusive of octroi, royality, Malkana, Toll tax, GST and any other taxes imposed by the Government. |
| 140 | Providing and fixing 32 mm (Thirty two millimetre) diametre P.V.C. flexible waste pipe of Finolex / Relpipe (Reliance )/Vectus for sink or wash basin including P.V.C. waste fittings complete including carriage of material within all leads, lifts and other incidentals as per specifications, approved drawing, design and as directed by the Engineer-In-Charge. The rate is inclusive of octroi, royality, Malkana, Toll tax, GST and any other taxes imposed by the Government. |
| 141 | Providing and fixing 25mm (twenty five millimetre) nominal size gun metal gate valve with C.I. wheel of approved quality (screwed end) including carriage of material within all leads, lifts and other incidentals as per specifications, approved drawing, design and as directed by the Engineer-In-Charge. The rate is inclusive of octroi, royality, Malkana, Toll tax, GST and any other taxes imposed by the Government. |
| 142 | Providing and fixing 15mm (Fifteen millimeter) diametre C.P. brass angle valve for basin mixer and geyser points of approved quality conforming to IS:8931, Jaquar / Hindware / Cera / Kerovite & Jal including carriage of material within all leads, lifts and other incidentals as per specifications, approved drawing, design and as directed by the Engineer-In-Charge. The rate is inclusive of octroi, royality, Malkana, Toll tax, GST and any other taxes imposed by the Government. |
| 143 | Providing and fixing 1216 (15mm (fifteen millimetre) OD pipe Polyethelene-Aluminium Polyethelene PE-AL- PE Composite Pressure Pipes conforming to IS - 1545 ,2004 of Kitec U.V. stabilized with carbon black having thermal stability for hot & cold water supply, capable to withstand temperature up to 80°C (Eighty degree celcius), including all special fittings of composite material (engineering plastic blend and brass inserts wherever required) e.g. elbows, tees, reducers, couplers & connectors etcetera with clamps at 1.00 metre (One metre) spacing for concealed works, including cutting chases, testing the joint and making good the wall etcetera complete as per architectural drawings including carriage of material within all leads, lifts and other incidentals, as per approved specifications drawing, design and as directed by the Engineer-In-Charge. The rate is inclusive of octroi, royality, Malkana, Toll tax, GST and any other taxes imposed by the Government. |
| 144 | Providing and fixing 1620 (20mm (Twenty millimetre) OD pipe Polyethelene-Aluminium Polyethelene PE-AL- PE Composite Pressure Pipes conforming to IS - 1545 ,2004 of Kitec U.V. stabilized with carbon black having thermal stability for hot & cold water supply, capable to withstand temperature up to 80°C (Eighty degree celcius), including all special fittings of composite material (engineering plastic blend and brass inserts wherever required) e.g. elbows, tees, reducers, couplers & connectors etcetera with clamps at 1.00 metre (One metre) spacing for concealed works, including cutting chases, testing the joint and making good the wall etcetera complete as per architectural drawings including carriage of material within all leads, lifts and other incidentals, as per approved specifications drawing, design and as directed by the Engineer-In-Charge. The rate is inclusive of octroi, royality, Malkana, Toll tax, GST and any other taxes imposed by the Government. |
| 145 | Providing and fixing 15mm (Fifteen millimetre) diametre to wall ceiling and floor galvanised mild steel tubes (Medium grade) tube fitting and clamps including making good the wall, ceiling and floor complete in all respect including carriage of material within all leads, lifts and other incidentals as per specifications, approved drawing, design and as directed by the Engineer-In-Charge. The rate is inclusive of octroi, royality, Malkana, Toll tax, GST and any other taxes imposed by the Government. |
| 146 | Providing and fixing 20mm (Twenty millimetre) diametre to wall ceiling and floor galvanised mild steel tubes (Medium grade) tube fitting and clamps including making good the wall, ceiling and floor complete in all respect including carriage of material within all leads, lifts and other incidentals as per specifications, approved drawing, design and as directed by the Engineer-In-Charge. The rate is inclusive of octroi, royality, Malkana, Toll tax, GST and any other taxes imposed by the Government. |
| 147 | Providing and fixing 25mm (Twenty five millimetre) diametre to wall ceiling and floor galvanised mild steel tubes (Medium grade) tube fitting and clamps including making good the wall, ceiling and floor complete in all respect including carriage of material within all leads, lifts and other incidentals as per specifications, approved drawing, design and as directed by the Engineer-In-Charge. The rate is inclusive of octroi, royality, Malkana, Toll tax, GST and any other taxes imposed by the Government. |
| 148 | Providing and fixing 600x450mm (Six hundered into four hundered fifty millimeters) bevelled edge mirror of superior glass mounted on 6mm (Six millimeters) thick hard board ground fixed to wooden cleats with C.P. brass screws and washers complete. including carriage of material within all leads, lifts and other incidentals as per specifications, approved drawing, design and as directed by the Engineer-In-Charge. The rate is inclusive of octroi, royality, Malkana, Toll tax, GST and any other taxes imposed by the Government. |
| 149 | Providing and fixing 600x120x5 mm (Six hundered into one hundered twenty into five millimetre) glass shelf of Jaquar / Hindware / Cera / Kerovite & Jal with edges round off, supported on anodised aluminium angle frame with C.P. brass brackets and guard rail complete fixed with 40mm (Forty millimetre) long screws, rawl plugs etcetera complete including carriage of material within all leads, lifts and other incidentals as per specifications, approved drawing, design and as directed by the Engineer-In-Charge. The rate is inclusive of octroi, royality, Malkana, Toll tax, GST and any other taxes imposed by the Government. |
| 150 | Providing and fixing CP brass soap Dish Holder having length of 138mm (one hundered thirty eight millimetre), breadth 102mm (one hundered two millimetre), height of 75mm (seenty five millimetre) with concealed fitting arrangements, weighing not less than 106 (one hundered six) gms complete including carriage of material within all leads, lifts and other incidentals as per specifications, approved drawing, design and as directed by the Engineer-In-Charge. The rate is inclusive of octroi, royality, Malkana, Toll tax, GST and any other taxes imposed by the Government. |
| 151 | Providing & Fixing in position Aluminium C.P glossy wall mounted 6 (six) pegs hooks rail fixed with C.P. brass screws and rawl plugs etcetera including carriage of material within all leads, lifts and other incidentals as per specifications, approved drawing, design and as directed by the Engineer-In-Charge. The rate is inclusive of octroi, royality, Malkana, Toll tax, GST and any other taxes imposed by the Government. |
| 152 | Providing and fixing C.P. brass toilet paper Holder including carriage of material within all leads, lifts and other incidentals as per specifications, approved drawing, design and as directed by the Engineer-In-Charge. The rate is inclusive of octroi, royality, Malkana, Toll tax, GST and any other taxes imposed by the Government. |
| 153 | Providing and fixing PVC connection pipe ISI marked 45cm (forty five centimeters) long and 15mm (fifteen millimeters) nominal bore with brass unions complete including carriage of material within all leads, lifts and other incidentals as per specifications, approved drawing, design and as directed by the Engineer-In-Charge. The rate is inclusive of octroi, royality, Malkana, Toll tax, GST and any other taxes imposed by the Government. |
| 154 | Providing and fixing 15mm (Fifteen millimeters) nominal bore brass full way valve with wheel of Jaquar / Hindware / Cera / Kerovite & Jal complete including carriage of material within all leads, lifts and other incidentals as per specifications, approved drawing, design and as directed by the Engineer-In-Charge. The rate is inclusive of octroi, royality, Malkana, Toll tax, GST and any other taxes imposed by the Government. |
| 155 | Providing and fixing 20mm (twenty millimeters) nominal bore brass full way valve with wheel of Jaquar / Hindware / Cera / Kerovite & Jal complete including carriage of material within all leads, lifts and other incidentals as per specifications, approved drawing, design and as directed by the Engineer-In-Charge. The rate is inclusive of octroi, royality, Malkana, Toll tax, GST and any other taxes imposed by the Government. |
| 156 | Providing and fixing 110mm (one hundered ten millimetre) diametre P.V.C single equal branch of Finolex / Relpipe (Relience) / Vectus with insertion rubber washer 3mm (Three millimeter) thick bolts and nuts ISI marked including finishing with approved adhesive complete including carriage of material within all leads, lifts and other incidentals as per specifications, approved drawing, design and as directed by the Engineer-In-Charge. The rate is inclusive of octroi, royality, Malkana, Toll tax, GST and any other taxes imposed by the Government. |
| 157 | Providing and fixing 75mm (Seventy five millimetre) diametre P.V.C single equal branch of Finolex / Relpipe (Relience) / Vectus with insertion rubber washer 3mm (Three millimeter) thick bolts and nuts ISI marked including finishing with approved adhesive complete including carriage of material within all leads, lifts and other incidentals as per specifications, approved drawing, design and as directed by the Engineer-In-Charge. The rate is inclusive of octroi, royality, Malkana, Toll tax, GST and any other taxes imposed by the Government. |
| 158 | Providing and fixing CP brass towel ring of Jaquar / Hindware / Cera / Kerovite & Jal trapezoidal shape 215 mm (two hundered fifteen millimetre) long, 200 mm (two hundered millimetre) wide with minimum distances of 37 mm (thirty seven millimetre) from wall face with concealed fittings arrangement of approved quality and colour, weighing not less than 88 (eighty eight) gms including carriage of material within all leads, lifts and other incidentals as per approved specifications, drawing, design and as directed by the Engineer-In-Charge. The rate is inclusive of octroi, royality, Malkana, Toll tax, GST and any other taxes imposed by the Government. |
| 159 | Providing and placing on terrace (at all floor levels) polyethylene water storage tank of Finolex / Vectus having tripple layer of IS No: 12701 marked, with cover and suitable locking arrangement and making necessary holes for inlet, outlet and overflow pipes including fittings but excluding the base support for tank complete including entire carriage of material within all leads, lifts and other incidentals, as per specifications, approved drawing, design and as directed by the Engineer-In-Charge. The rate is inclusive of octroi, royality, Malkana, Toll tax, GST and any other taxes imposed by the Government. |
| 160 | Providing and laying cement concrete 1:4:8 (One Cement isto four Sand isto eight graded stone aggregate 40mm (Forty millimetre) nominal size ) all round for PVC. pipes of 150mm (One hundered fifty millimetre) internal diameters, for bedding , for senior pipe necessary form work and curing complete including entire carriage of material within all leads, lifts and other incidentals, as per specifications, approved drawing, design and as directed by the Engineer-In-Charge. The rate is inclusive of octroi, royality, Malkana, Toll tax, GST and any other taxes imposed by the Government. |
| 161 | Providing and laying cement concrete 1:3:6 (One Cement isto three Sand isto six graded stone aggregate 40mm (Forty millimetre) nominal size ) all round for PVC. pipes of 150mm (One hundered fifty millimetre) internal diameters, for hauching, necessary form work and curing complete including entire carriage of material within all leads, lifts and other incidentals, as per specifications, approved drawing, design and as directed by the Engineer-In-Charge. The rate is inclusive of octroi, royality, Malkana, Toll tax, GST and any other taxes imposed by the Government. |
| 162 | Constructing brick masonry manhole in cement mortar 1:4 (One cement isto Four coarse sand ) with R.C.C. top slab with 1:2:4 mix (One cement isto two coarse sand (zone- III) isto four graded stone aggregate 20 mm (Twenty millimetre) nominal size), foundation concrete 1:4:8 mix (One cement isto Four coarse sand (zone- III) isto Eight graded stone aggregate 40 mm (Forty millimetre) nominal size), inside plastering 12 mm (Twelve millimetre) thick with cement mortar 1:3 (One cement isto Three coarse sand) finished with floating coat of neat cement and making channels in cement concrete 1:2:4 (One cement isto Two coarse sand isto Four graded stone aggregate 20 mm (Twenty millimetre) nominal size) finished with a floating coat of neat cement complete as per standard design Inside size 90x80cm (Ninety into eighty centimetre) and 45cm (Forty five centimetre) deep including C.I. cover with frame (light duty) 455x610mm (Four hundered fifty five into six hundered ten millimetre) internal dimensions, total weight of cover and frame to be not less than 38 Per Kilogram (Thirty eight kilograms) (weight of cover 23 Per Kilogram (Twenty three kilograms) and weight of frame 15 Per Kilogram (Fifteen kilograms) With Sewer bricks conforming to IS : 4885 complete including carriage of material within all leads, lifts and other incidentals as per specifications, approved drawing, design and as directed by the Engineer-In-Charge. The rate is inclusive of octroi, royality, Malkana, Toll tax, GST and any other taxes imposed by the Government. |
| 163 | Constructing brick masonry manhole in cement mortar 1:4 (One cement isto Four coarse sand ) with R.C.C. top slab with :2:4 mix (One cement isto two coarse sand (zone- III) isto four graded stone aggregate 20 mm (Twenty millimetre) nominal size), foundation concrete 1:4:8 mix (One cement isto Four coarse sand (zone- III) isto Eight graded stone aggregate 40 mm (Forty millimetre) nominal size), inside plastering 12 mm (Twelve millimetre) thick with cement mortar 1:3 (One cement isto Three coarse sand) finished with floating coat of neat cement and making channels in cement concrete 1:2:4 (One cement isto Two coarse sand isto four graded stone aggregate 20 mm (Twenty millimetre) nominal size) finished with a floating coat of neat cement complete as per standard design Inside size 120x90cm (One hundered twenty into ninety centimetre) and 90cm (Ninety centimetre) deep including C.I. cover with frame (light duty) 455x610 mm (Four hundered fifty five into six hundered ten millimetre) internal dimensions, total weight of cover and frame to be not less than 38 Per Kilogram (Thirty eight kilograms) (weight of cover 23 Per Kilogram (Twenty three kilograms) and weight of frame 15 Per Kilogram Fifteen kilograms) With Sewer bricks conforming to IS : 4885 complete including carriage of material within all leads, lifts and other incidentals as per specifications, approved drawing, design and as directed by the Engineer-In-Charge. The rate is inclusive of octroi, royality, Malkana, Toll tax, GST and any other taxes imposed by the Government. |
| 164 | Constructing brick masonry chamber for underground C.I. inspection chamber and bends with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in cement mortar 1:4 (One cement isto Four coarse sand) C.I. cover with frame (light duty) 455x610mm (Four hundered fifty five into six hundered ten millimetre) internal dimensions, total weight of cover with frame to be not less than 38 Per Kilogram (Thirty eight kilograms) (weight of cover 23 Per Kilogram (Twenty three kilograms) and weight of frame 15 Per Kilogram (Fifteen kilograms) ), R.C.C. top slab with 1:1.5:3 mix (One cement isto One and Half Fine sand isto Three graded stone aggregate 20 mm (Twenty millimetre) nominal size), foundation concrete 1:5:10 (One cement isto Five fine sand isto ten graded stone aggregate 40 mm (Forty millimetre) nominal size), inside plastering 12 mm (Twelev millemetre) thick with cement mortar 1:3 (One cement isto Three coarse sand), finished smooth with a floating coat of neat cement on walls and bed concrete etcetera complete as per standard design Inside dimensions 455x610 mm (Four hundered fifty five into six hundered ten millmetre) and 45 cm (Forty five centimetre) deep for single pipe line complete including carriage of material within all leads, lifts and other incidentals as per specifications, approved drawing, design and as directed by the Engineer-In-Charge. The rate is inclusive of octroi, royality, Malkana, Toll tax, GST and any other taxes imposed by the Government. |
| 165 | Providing and fixing 455x610mm (Four hundered fifty five into six hundered ten millimetre) light duty rectangular cast iron manhole with frame cover weight 23 Kilogram (Twenty three kilograms) single seal pattern complete including carriage of material within all leads, lifts and other incidentals as per approved specifications, drawing, design and as directed by the Engineer-In-Charge. The rate is inclusive of octroi, royality, Malkana, Toll tax, GST and any other taxes imposed by the Government. |
| 166 | Supplying and fixing C.I. cover 300x300 mm (three hundered into thhree hundered millimetre) without frame for gully trap (standard pattern) the weight of cover to be not less than 4.5 Kilogram (four point five kilogram) complete including carriage of material within all leads, lifts and other incidentals as per approved specifications, drawing, design and as directed by the Engineer-In-Charge. The rate is inclusive of octroi, royality, Malkana, Toll tax, GST and any other taxes imposed by the Government. |
| 167 | Providing and fixing S.F.R.C heavy duty manhole cover Circular shape 560mm (five hundered sixty millimetre) diametre precast R.C.C. manhole cover with frame - H.D. - 20 (twenty) within all leads, lifts and other incidentals as per approved specifications, drawing, design and as directed by the Engineer-In-Charge. The rate is inclusive of octroi, royality, Malkana, Toll tax, GST and any other taxes imposed by the Government. |
| 168 | Provision for water lifting pump 1.00 HP (One point zero zero horse power) of serex/Kirloskar/Crompton/Wortington including all necessary fittings complete including carriage of material within all leads, lifts and other incidentals as per approved specifications, drawing, design and as directed by the Engineer-In-Charge. The rate is inclusive of octroi, royality, Malkana, Toll tax, GST and any other taxes imposed by the Government. |
| 169 | Providing and fixing 25 mm (twenty five millimetre) diametre fire hydrent inculuding all necessary fiting compelete including carriage of material within all leads, lifts and other incidentals as per approved specifications, drawing, design and as directed by the Engineer-In-Charge. The rate is inclusive of octroi, royality, Malkana, Toll tax, GST and any other taxes imposed by the Government. Please Enable Macros to View BoQ information |
AI Tender Summary
Tender Timeline
Jul 09, 2026
11:30 IST
Tender Published
Tender notice published.
CompletedJul 15, 2026
17:00 IST
Bid Submission Deadline
Online submission via eProcurement portal.
Upcoming · 5 daysJul 16, 2026
Bid Opening Date
Technical bids will be opened and evaluated.
Upcoming · 6 daysTender Documents
Download All (ZIP) ↓
Disclaimer
We takes all possible care for accurate & authentic tender information. However users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender