Tender For Providing And Installation Of 1 No. India Mark-Iii (65 Mm) And India Mark-Ii (32Mm) Deepwell Hand Pump At Shamlech Near Vikas Mashroom Farm Tehsil & Distt. Solan. (Sh:- Drilling By Dth/ Odex Percussion/ Calyx/ Rc Portable Rigs 100 Metres D
Tender Value
6.02 Lakhs
Estimated cost
Bid Submission
16 Jul 2026
5 days left
EMD
12050
Bank guarantee accepted
Document Fee
350
Non-refundable
Tender Type
Online
Tender Overview
Organization
Tender ID
Competition Type
NCB
Bidding Type
Tender
Location / State
Solan → Himachal Pradesh
EMD Exemption
Not Available
Quantity
Not Available
Website
Contact Person
Address
Project Description
Tender for Providing And Installation Of 1 No. India Mark-Iii (65 Mm) And India Mark-Ii (32Mm) Deepwell Hand Pump At Shamlech Near Vikas Mashroom Farm Tehsil & Distt. Solan. (Sh:- Drilling By Dth/ Odex Percussion/ Calyx/ Rc Portable Rigs 100 Metres Deep & Its Energisation).
BOQ
| Sl. No. | Item Description |
| 1 | Transportation of suitable truck/ tractor where only road available, DTH & ODEX/ Percussion Calyx/ RC drilling with portable rigs alongwith necessary accessories etc. to the site of work and erection of portable rig including levelling etc. complete in all respects as per directions of Engineer-in- Charge. |
| 2 | Drilling bores of 165mm dia as per IS:2800-1979 using DTH from ground level in the over burden as per directions of Engineer-in-Charge/ Hydrogeologist, with suitable rigs for drilling through rocky formations consisting of sand stone, limestone, dolomites, conglomerate, silt, clay or any other type of sedimentary, metamorphic and igneous rock including cost of attachments, consumable stores, bits, water, POL etc. complete in all respect as detailed below:- |
| 3 | From 0m to 20m depth |
| 4 | Drilling bores of 152 mm dia as per IS : 2800-1979 using ODEX (TUBEX) attachement required drilling in collapsible strata conglomerate, boulder, pebble,gravels, silt, clay etc. including cost of attachments, consumable stores, bits, water, POL etc. complete with system of simultaneous lowering of 125 mm nominal bore, 5.0 mm thick MSERW fincut casing pipe which will be welded together using 2.5 mm or 3.25 mm dia. Advani Oerlikon electrodes, with one plain end and the other end chamfered to 50 degrees removing paint on the area to be welded, inclusive of the cost of bio-degradable and non-toxic foam flush etc. complete in all respects as per directions of Engineer-in-Charge. MSERW fincut casing pipe, casing shoe and bit tube as per requirement of ODEX to be paid separately. |
| 5 | Non Trible Area |
| 6 | Supplying and lowering of IS Marked 125 mm dia PVC casing pipe medium class 5mm thick screwed and socketed as per IS 12818-1992 (Part-1) with upto date ammendments including cost of all cuttings, factory threadings, welding, wherever required, in random lengths of 6 mtrs. including transportation charges (For DTH bores) complete in all respect as per direction of Engineer-in-charge. |
| 7 | Non Trible Area |
| 8 | Supplying and lowering of IS Marked 125 mm dia N.B. 5mm thick fincut MSERW casing pipes as per IS : 4270-2001 and requirement of ODEX attachement from approved manufacturers complete in all respect as per direction of Engineer-in-charge. |
| 9 | Non Trible Area |
| 10 | Prividing and fixing suitable casing shoe and bit tube as per requirement of ODEX attachment complete in all respect as per directions of Engineer-in- Charge. |
| 11 | Non Trible Area |
| 12 | Collection and preservation of soil samples in polythene bags after every 1 metre complete in all respects as per directions of Engineer-in- charge. |
| 13 | Development of borewell and yield testing with air compressor through V notch and disinfection etc. complete in all respects as per IS 2800: 1979 and as per directions of Engineer-in Charge. |
| 14 | Providing & installing submersible pump conforming to ISS 9034-1976 alongwith directly coupled submersible type squirrel cage electric induction motor suitable for operation on 415 volt. 3 Phase 50 C.P.S.A.C supply water lubricated bearing and provided with pivoted segment thrust bearing to with stand normal vertical lead with minimum wear & tear and dully fitted with device to take upto the expension of water with heating of motor complete of make KSB/ Kirloskar/ Mather & Platt complete in all respect as per direction of Engineer-in-Charge. (1set of 5HP). |
| 15 | Supply & fixing of L&T/ Havells/ Standard make control panel for submersible pump complete with shaft and angle iron, febricated dully painted and complete with internal wiring and comparising of air break starter mainswitch of suitable amp., T.P. volt meter, ameter, phase indicating lamps complete in all respects including entire carriage of material upto all lifts & leads. |
| 16 | Supply and fixing stainless steel rope wire suitable to wear the weight of motor pump complete in all respect. |
| 17 | Supplying and fixing supporting clamps to submersible pump sets complete in all respects including entire carriage of material upto all lifts & leads. |
| 18 | Supply & fixing of 4x6mm PVC insulated copper around cable complete in all respects including entire carriage of material upto all leads & lifts. |
| 19 | Lowering and jointing of PVC pipe 32mm dia 10KG pressure heavy duty complete in all respects including entire carriage of material upto all lifts & leads. |
| 20 | Providing and fixing MS adaptor of 32mm complete in all respects including entire carriage of material upto all lifts & leads Please Enable Macros to View BoQ information |
AI Tender Summary
Tender Timeline
Jul 08, 2026
11:30 IST
Tender Published
Tender notice published.
CompletedJul 16, 2026
17:00 IST
Bid Submission Deadline
Online submission via eProcurement portal.
Upcoming · 5 daysJul 16, 2026
Bid Opening Date
Technical bids will be opened and evaluated.
Upcoming · 5 daysTender Documents
Download All (ZIP) ↓
Disclaimer
We takes all possible care for accurate & authentic tender information. However users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender