Tender For Repair / Maintenance Of Installed Pumping Sets, Starter, Electric Motors, Control Panels And Connected Items Of Water Supply Installations Of Cvd Family Quarter Area, 60 Inf Bde, Cvd Depot Pump House, Old Base Hospital, Hazipeer Line And S
Tender Value
36 Lakhs
Estimated cost
Bid Submission
29 Jul 2026
20 days left
EMD
72000
Bank guarantee accepted
Document Fee
500
Non-refundable
Tender Type
Online
Tender Overview
Organization
Tender ID
Competition Type
NCB
Bidding Type
Tender
Location / State
New Delhi → Delhi
EMD Exemption
Available
Quantity
Not Available
Website
Contact Person
Address
Project Description
Tender for Repair / Maintenance Of Installed Pumping Sets, Starter, Electric Motors, Control Panels And Connected Items Of Water Supply Installations Of Cvd Family Quarter Area, 60 Inf Bde, Cvd Depot Pump House, Old Base Hospital, Hazipeer Line And Shekhawati Line, Area Of Age(U) Water Supply No-1 Under Ge(U) Water Supply Delhi Cantt-10.
BOQ
| Sl. No. | Item Description |
| 1 | Disconnecting of electric connections from LT control panel and starter of submersible pump set of size 5 to 12.5 HP ,removing the pipe line connections from discharge side and taking down/out submersible pump set along with column pipe from bore well with the help of chain pully block including transportation to workshop for repairs and back , lowering the pump in bore well after repairs after replacement of rusted nuts, bolts, washers, rubber gasket etc including testing complete all as specified and as directed. |
| 2 | Disconnecting of electrical connections from panel board including disconnecting the cable leads from the motor terminal box and taking down/out electric motor of any capacities and makes from base plate of pump set after opening the nuts, bolts etc. Dismantling the induction/Submersible motor and seperate the stator and rotor and removing the Unserviceable DE & NDE sede bearing, burnt winding wire from stator and rewinding the same as per existing supper enamelled copper wire gauge F class insulation used including varnishing and heating for drying of winding, transporting the motor to workshop for repair and back, re-installed after repair including testing complete all as specified and directed . |
| 3 | Disconnecting of electric connection and De-coupling the Centrifugal pump of capacity 10 to 15 HP and removing from foundation for repair after opening /cutting the rusted nuts, bolts etc and dismantling complete pump and repairing the same with replacing the following unserviceable spare parts i.e CI Casing wear ring, interstage ring, stuffing box bush, lentern ring, eye bolt with nut, shaft sleeve, impeller key, coupling key, water liquid reflector, bearing cartridge, bearing plate, shaft bush, MS stud with nut, gland rope, gasket packing including grinding work of lathe machine and re-assembling the same including the transporting the pump from side to workshop for repair and back, re-installed at existing position after repair and providing new MS nuts, bolts,packing flange etc including testing complete all as specified and directed. |
| 4 | Disconnecting of electric connection and De-coupling the Centrifugal pump of capacity 20 to 30 HP and removimg from foundation for repair after opening /cutting the rusted nuts, bolts etc and dismantling complete pump and repairing the same with replacing the following unserviceable spare parts i.e CI Casing wear ring, interstage ring, stuffing box bush, lentern ring, eye bolt with nut, shaft sleeve, impeller key, coupling key, water liquid reflector, bearing cartridge, bearing plate, shaft bush, MS stud with nut, gland rope gasket packing including grinding work of lathe machine and re-assembling the same including the transporting the pump from side to workshop for repair and back, re-installed at existing position after repair and providing new MS nuts, bolts,packing flange etc including testing complete all as specified and directed. |
| 5 | Disconnecting of electric connection and De-coupling the Centrifugal pump of capacity 40/50HP and removing from foundation for repair after opening /cutting the rusted nuts, bolts etc and dismantling complete pump and repairing the same with replacing the following unserviceable spare parts i.e CI Casing wear ring, interstage ring, stuffing box bush, lentern ring, eye bolt with nut, shaft sleeve, impeller key, coupling key, water liquid reflector, bearing cartridge, bearing plate, shaft bush, MS stud with nut, gland rope gasket packing including grinding work of lathe machine and re-assembling the same including the transporting the pump from side to workshop for repair and back, re-installed at existing position after repair and providing new MS nuts, bolts,packing flange etc including testing complete all as specified and directed. |
| 6 | Disconnecting the electric connection of monoblock pump of capacity 1 to 3 HP and removing the same from foundationfor repair after opening /cutting the rusted nuts, bolts etc and dismantling complete pump and repairing the same with replacing the following unserviceable spare parts i.e CI Impeller, GM shaft sleeve, Mechanical seal, water seal, water liquid reflector, MS stud with nut, gland rope gasket packing including grinding work of lathe machine and re-assembling the same including the transporting the pump from side to workshop for repair and back, re-installed at existing position after repair and providing new MS nuts, bolts,packing flange etc including testing complete all as specified and directed. |
| 7 | Disconnecting the electric connection of monoblock pump of capacity 5 to 7.5 HP and removing the same from foundationfor repair after opening /cutting the rusted nuts, bolts etc and dismantling complete pump and repairing the same with replacing the following unserviceable spare parts i.e CI Impeller, GM shaft sleeve, Mechanical seal, water seal, water liquid reflector, MS stud with nut, gland rope gasket packing including grinding work of lathe machine and re-assembling the same including the transporting the pump from side to workshop for repair and back, re-installed at existing position after repair and providing new MS nuts, bolts,packing flange etc including testing complete all as specified and directed. |
| 8 | Dismantling complete submersible pump of capacity 5 to 7.5 HP and repairing the same with replacing the following unserviceable spare parts i.e GM bush, roror sleeve, water seal, thrust bearing, sealing ring, upper & lower housing flange upper & lower with stud and nut, wire mesh, drain plug, SS distance sleeve, impeller key, inter ring GM neck ring, Guide bush, GM impeller/EPV Impeller, CI section chamber,SS coupling, CI stage bowl, T bolt with nut including grinding work of lathe machine and re-assembling the same testing complete all as specified and directed |
| 9 | Dismantling complete submersible pump of capacity 10 to 12.5 HP and repairing the same with replacing the following unserviceable spare parts i.e GM bush, roror sleeve, water seal, thrust bearing, sealing ring, upper & lower housing flange upper & lower with stud and nut, wire mesh, drain plug, SS distance sleeve, impeller key, inter ring GM neck ring, Guide bush, GM impeller/EPV Impeller, CI section chamber,SS coupling, CI stage bowl, T bolt with nut including grinding work of lathe machine and re-assembling the same testing complete all as specified and directed |
| 10 | Supply and Fixing in replacement of Ball Bearing 6306 |
| 11 | Supply and Fixing in replacement of Ball Bearing 6307 |
| 12 | Supply and Fixing in replacement of Ball Bearing 6308 |
| 13 | Supply and Fixing in replacement of Ball Bearing 6309 |
| 14 | Supply and Fixing in replacement of Ball Bearing 6310 |
| 15 | Supply and Fixing in replacement of Ball Bearing 6312 |
| 16 | Supply and Fixing in replacement of Ball Bearing 6314 |
| 17 | Supply and fixing spare tyre for coupling type TC/P/011 after taking down/out as existing at site complete all as specified and directed. |
| 18 | Supply and fixing spare tyre for coupling type TC/P/013 after taking down/out as existing at site complete all as specified and directed. |
| 19 | Supply and fixing spare tyre for coupling type TC/P/014 after taking down/out as existing at site complete all as specified and directed |
| 20 | Supply and fixing spare tyre for coupling type TC/P/015 after taking down/out as existing at site complete all as specified and directed. |
| 21 | Supply and fixing spare tyre for coupling type TC/P/019 after taking down/out as existing at site complete all as specified and directed. |
| 22 | Material and labour for Aluminnium Spray painting by airless compressor with high pressure Two coat of synthetic enamel paint as per existing pattern or scheme, on centrifugal pump & motor of any capacity rating 5-50 HP upto NRV or sluice valve,and MS Base channel including preparation of surfaces by scratching and removing all the rust complete all as specified and directed. |
| 23 | Supply and Fixing in replacement MS base channel of size as exists including fabrication from structural steel sections including nuts, bolts, washers, welding, bending cold or hot, drilling holes for bolts in any shape or size as indicated or directed and inclusive of one primer coat, one under coat and one finshing coat of paint. |
| 24 | Supplying , laying , jointing, welding and testing MS Pipe (Heavy class 'C') IS : 1239/3589, of followiing sizes laid in trenches or in Horizontal/Vertical/inclined position or laying on floors for connections for suction, to header and connected to out going water main CI/DI/GI pipe line, for following size including taking out the old unserviceable pipes.Note:- MS Flanges incl fabrication work will be measured and paid separately. |
| 25 | 80mm dia |
| 26 | 100 mm dia |
| 27 | 150 mm dia |
| 28 | Supply and fixing in replacement of MS flange 16mm thick duly welded with flange joint including nuts bolts, washer, Rubber or fiber board gasket joint of following sizes. |
| 29 | 80mm bore |
| 30 | 100 mm bore |
| 31 | 150 mm bore |
| 32 | Material and labour for PCC (1:4:8) type D2 (with 40 mm graded aggregate) as in Providing, cement concrete in roof kerbs or mud stops, rounded or chamfered on edges, coping, grouting, MS nut for motor base, finished even and smooth without using extra cement as on brick work/flooring complete including demilition of PCC all as specified and directed. |
| 33 | Supply and Fixing in replacement of Anti Vibration Pad with nuts, bolts and washers complete all as specified and directed. |
| 34 | Excavation in trenches not exceeding 1.5 mtr wide and not exceeding 1.5 m in depth for taking out/laying of under ground cables/pipes etc n. exc 10 sqm on plan and n. exc 1.5 m in depth and getting out and in hard/dence soil. |
| 35 | Returning fillling in including spreding, leveling, watering and well ramming in layers not exc 25 cm thick all as specifed and directed by Engineer-in-charge. |
| 36 | Removing execavated material from site to a distance not exc 50 metres away and depositing where directed not exc 1.5 metres from the starting point all as specified and directed by Engineer-in-charge |
| 37 | Supplying and laying well burnt bricks sub class B for protection of cable complete all as specified and directed |
| 38 | M&L Sand filling under and above the electrical cable for cable cushioning complete all as specified and directed. |
| 39 | Material and Labour XLPE insulated, armoured heavy duty electric cable with aluminium conductor 1100 volts grade cross sectional area 16 sq mm 4 core laying in treanches/floor/wall including taking out old unserviceable cable and connection to panel for incoming and out going using aluminium lugs complete all as specified and directed by Engineer-in-Charge. |
| 40 | Material and Labour XLPE insulated, armoured heavy duty electric cable with aluminium conductor 1100 volts grade cross sectional area 25 sq mm 4 core laying in treanches/floor/wall including taking out old unserviceable cable and connection to panel for incoming and out going using aluminium lugs complete all as specified and directed by Engineer-in-Charge. |
| 41 | Material and Labour XLPE insulated, armoured heavy duty electric cable with aluminium conductor 1100 volts grade cross sectional area 35 sq mm 3.5 core laying in treanches/floor/wall including taking out old unserviceable cable and connection to panel for incoming and out going using aluminium lugs complete all as specified and directed by Engineer-in-Charge. |
| 42 | Openning of gland packing coupling and removing the unserviceable gland rope from centrifugal/Monoblock pump set of capacity 10 to 100 HP and fixing the new gland rope all as per existing size gland rope complete all as specified and directed. |
| 43 | Openningcutting of nut bolts & stem and removing the unserviceable gland rope from Sluice valve of size 100 to 300 mm dia and fixing the new gland rope all as per existing size gland rope complete all as specified and directed. |
| 44 | Excavation in trenches by cutting of road crossing, PCC hard standing for taking out/laying of cables including M& L for PCC (1:2:4) type B-I (with 20 mm graded aggregate) as in coping, grouting, finished even and smooth without using extra cement as on brick work/flooring complete making good the existing surface complete all as specified and as directed. |
| 45 | M & L for heat shrinkable LT 1100V straight through joint suitabel for aluminium conductor cable of size 25 to 50 sqmm complte all as specified and diretced. |
| 46 | Analog time switch type QT (daily) model FM/1 QUARTZ, voltage 240 VAC,50 Hz, Contact rating 16 A/250 VAC complete all as specified and directed. |
| 47 | S&F in replacement rotational moulded polythylene water storage tanks of capacity 500 ltr triple layer cylindrical vertical with closed top hoisted and fixed in position for priming of centrifugal pump set all as specified in SSR part I |
| 48 | S&F in replacement rotational moulded polythylene water storage tanks of capacity 1000 ltr triple layer cylindrical vertical with closed top hoisted and fixed in position for priming of centrifugal pump set all as specified in SSR part I |
| 49 | Supply & Laying in replacement of 20 mm bore GI pipe mediun grade ISI mark including all fittings in old/new positions in trenches/wall/floor complet and making good the distributed surfaces as per existing complete all as specified and directed . |
| 50 | Supply & fixing in replacement of 20 mm Gun metal gate valve with iron wheel head screwed both ends for iron pipe as per IS-778 compete, ISI marked complete all as specified and directed. |
| 51 | Supplying and fixing MS column pipe, heavy grade, class 'C', 50 mm bore , heavy duty, flange welded on both ends of size 3 mtr length complete all as specified and directed. Note: rate quoted for taking up/down is deemed to be included in item No. 1 |
| 52 | Supplying and fixing MS column pipe, heavy grade, class 'C', 80 mm bore , heavy duty, flange welded on both ends of size 3 mtr length complete all as specified and directed. Note: rate quoted for taking up/down is deemed to be included in item No. 1 |
| 53 | Supply & fixing in replacement submersible copper cable of size 4 Sq mm 3 core, 1100 Volts complete all as specified and as directed by engr-in-charge . |
| 54 | M&L for re-development of bore well of any capacity and size at the pressure 22 kg/sqcm to 25 kg/sqcm by DTH machine of capacity 1200 cfm includiing air pipe and connected items to improve the yield of tube well by DTH machine including transportation of machine all as specified and directed |
| 55 | Testing the cables with high voltage DC testing machine and locating the fault in the cables by fault locating machine to pin point exact position of fault, disconnecting faulty 1100 volts LT cables of different sizes from both ends, removal of fault, Reconnection and testing of cables after removal of fault complete all as specified and directed by Engr-in-charge. NOTE:(a) 1100 volt cables and joints shall be measured and paid for seperately under respective items of schedule (b) Retrieved old serviceable cable cover/ bricks will be laid in trenches for cable protection. If extra PCC cover / bricks and sand required at site shall be measured and paid separately under respective items of BOQs. (c) Exacavation and earth work will be measured and paid for separately under respective items of schedule. |
| 56 | Materil and labour for pump shaft stainless steel suitable for 15 HP centrifugal pump set including turning, grinding and balancing work. |
| 57 | Materil and labour for pump shaft stainless steel suitable for 40 HP centrifugal pump set including turning, grinding and balancing work. |
| 58 | Materil and labour for pump shaft stainless steel suitable for 50 HP centrifugal pump set including turning, grinding and balancing work. |
| 59 | Materil and labour for CI impeller suitable for 15 to 20 HP centrifugal pump set including turning, grinding and balancing work. |
| 60 | Materil and labour for CI impeller suitable for 30 HP centrifugal pump set including turning, grinding and balancing work. |
| 61 | Materil and labour for CI impeller suitable for 40 HP centrifugal pump set including turning, grinding and balancing work. |
| 62 | Taking up suction pipe of size 80/100/150 mm dia after opening of nuts and bolts and open the bottom plate of Swing type CI foot valave and replace the unserviceable leather Gasket of swing disc as per existing size but the minimum thickness is not less than 6 mm. |
| 63 | Supply & Fixing in replacement PVC insulated multistranded copper conductor wire of 16 Sqmm size, single core, 1100 volts complete all as specified and as directed. |
| 64 | Supply & Fixing in replacement PVC insulated multistranded copper conductor wire of 25 Sqmm size, single core, 1100 volts complete all as specified and as directed. |
| 65 | Supply & fixing in replacement of MCCB thermal relay range 320- 400 Amps, 4 pole 415V of breaking capacity 50 KA and and connecting to bus bars and cable end termination with suitable lugs complete all as specified and directed. |
| 66 | Supply & fixing in replacement MCCB thermal relay range 200- 250 Amps, 4 pole 415V of breaking capacity 36 KA and and connecting to bus bars and cable end termination with suitable lugs complete all as specified and directed |
| 67 | Supply & fixing in replacement MCCB thermal relay range MCCB 160-200 Amps, 4 pole, 415 V, breaking capacity 36 KA complete all as specified and directed. |
| 68 | Supply & fixing in replacement MCCB thermal relay range 4 pole MCCB 100-125 Amps,415V, breaking capacity 18 KA |
| 69 | Supply & fixing in replacement MCCB thermal relay range 4 pole MCCB 63-80 Amps,415 V, breaking capacity 18 KA complete all as specified and directed. |
| 70 | Supply and fixing fully automatic stat delta motor starter MN or ML suitable for 17.5 HP of motor rating AC 3 duty 415V 50 Hz 3 phase, ML-1.5/MN 16 FASD relay range 9-15 Amps including taking down old starter complete all as specified and directed. |
| 71 | Supply & Fixing fully automatic star delta motor starter MN or ML suitable for 30 HP of motor rating AC 3 duty 415V 50 Hz 3 phase, ML-2/MN 25 FASD relay range 14-23 Amps including taking down old starter complete all as specified and directed. |
| 72 | Supply & Fixing fully automatic stat delta motor starter suitable for 40 HP of motor rating AC 3 duty 415V 50 Hz 3 phase, ML-3 / MN 32 FASD relay range 20-33 Amps including taking down old starter complete all as specified and directed. |
| 73 | Supply & Fixing fully automatic stat delta motor starter type suitable for 50 HP of motor rating AC 3 duty 415V 50 Hz 3 phase, ML-4 / MN 45 FASD relay range 30-50 Amps including taking down old starter complete all as specified and directed. |
| 74 | Supply and fixing DOL motor starter suitable for 10 HP of motor rating AC 3 duty 415V 50 Hz 3 phase, ML / MN relay range 9-15 Amps including taking down old starter complete all as specified and as directed by Engr in charge |
| 75 | Supply & Fixing in replacement 3 pole power contactor type ML-1.5 or MNX type, 415 Volts, 50 HZ range 25 Amps complete all as specified and as directed |
| 76 | Supply & Fixing in replacement 3 pole power contactor type ML-2 or MNX type, 32 Amps, 415 Volts, 50 HZ complete all as specified and as directed |
| 77 | Supply & Fixing in replacement 3 pole power contactor type ML-3 or MNX type, 40 Amps, 415 Volts, 50 HZ complete all as specified and as directed. |
| 78 | Supply & Fixing in replacement 3 pole power contactor type ML-4, 70 Amps, 415 Volts, 50 HZ complete all as specified and as directed. |
| 79 | Supply & Fixing in replacement of over load replay type ML 1.5/2 or MNX type , relay range 13-21 Amp complete all as specified and as directed. |
| 80 | Supply & Fixing in replacement of over load relay type ML 2 or MNX type, relay range 20-32 Amps complete all as specified and as directed. |
| 81 | Supply & Fixng in replacement of over load relay type ML 3 or MNX type , relay range 28-42 Amps complete all as specified and as directed. |
| 82 | Supply and installation of flanged ends Water Meter woltman type, including testing and making good connection with flanged ends, with gasket rubber sheet and nut & bolts etc ISI Marked fixing in horizontal / incline / vertical position, including taking out unserviceable of following sizes complete all as specified and as directed at site by the Engineer-in-Charge. |
| 83 | 100 mm bore |
| 84 | 150 mm bore |
| 85 | Supply and Fixing in replacement of CI Foot valve of following size , Flanged ends, Swing type opration with rubber sheet as per IS-4038 including taking out unserviceable of following sizes all as specified and directed by Engineer-in-Charge. Note :- Flanged joints complete with jointing material shall deemed to be included in the unit rate of this items. |
| 86 | 80 mm bore |
| 87 | 100 mm bore |
| 88 | 150 mm bore |
| 89 | Supply and installation of flanged ends strainer/dirt box, PN-10 with stainless steel mesh suitable for water meter for potable water supplies on up stream of water meter to avoid foreign material entering into meter including taking out unserviceable of following sizes complete all as specified and as directed at site by the Engineer-in-Charge. |
| 90 | 100 mm bore |
| 91 | 150 mm bore |
| 92 | Material and labour including jointing and testing of cast iron sluice valves class PN-1.0, conforming to IS:14846 flanged ends drilled having stainless steel spindle with cast iron wheel at top complete with nuts, bolts, washers and rubber gaskets including taking out unserviceable sluice valve and removal from site for the follwing sizes complete all as specified . |
| 93 | 80 mm bore |
| 94 | 100 mm bore |
| 95 | 150 mm bore |
| 96 | Supply and fixing jointing and testing of cast iron Non return valve without by pass arrangment swing type confirming to IS 5312 flanged ends pressure rating PN 1.0 complete including taking out unserviceable NRV all as specified and as directed by Engineer-in-Charge. Note - Flanged joints complete with rubber jointing materail shall deemed to be included in the unit rate of this item |
| 97 | 80 mm bore |
| 98 | 100 mm bore |
| 99 | 150 mm bore |
| 100 | Supply & fixing , install testing and commissioning of LT panel ,outdoor type cubical shape,three phase, 4 wire, Aluminium bus bar for phases and neutral made out of CRCA Steel sheet 3.0 mm thick sheet ,factory fabricated, CPRI approved, dust and vermin proof, sloopy roof, opening at bottom for cable in/ Out, provn for ventilation, angle iron frame and four legs of 50x50x6mm thick angle iron, 2 ft long grouted on PCC foundation of height not less than 30 cm from the ground level, grouting properly, and of suitable size to accomodate the items mentioned below and having seperate compartment /chambers for cable gallery busbar, switch gear all as specified and comprising of following including necessary cable connections to the MCCBs, voltmeter, Ammeter and cable lugs, spreader terminals etc.(a) Aluminium bus bar with PVC sleeve suitable for 200 amps for Phase & 100 Amp for Neutral - 01Set.(b) Voltmeter, digital type 0- 500 Volt,with selector switch - 01 set Make: DIP/AE/IMP/NSD(c) Ammeter Digital type 0-200 Amps, with selector switch and CT - 03 set Make: DIP/AE/IMP/NSD(d) Phase indicating lamps LED type ( red , yellow, blue) 01 set(e) Incoming MCCB 63 Amp 4 pole 16 KA - 01 No (f) Outgoing MCCB 40 Amp 3 pole 16 KA -01 Nos (g) FASD Starter ML-1.5 with MS sheet enclosure -01 Nos (h) Outgoing MCB SPN 20 Amp, 230 Volts 10 KA -01 No (j) Smart water pump control system (Varun -S3 (RF + GSM) with SIM & 1 Year Recharge complete |
| 101 | Supply , installation, commissioniong and testing of smart water pump control system in borewell up to 10 HP including varun controller, remote, 02 no. of antennas (RF+GSM), user manual M2M SIM complete all as specified and as directed at site by the Engineer-in-Charge. Features: LCD Display, Dry run and over run protection, Smart Scheduling, App based control & Notifications, Internet free control with GSM and app control. |
| 102 | An amount of Rs 2,01,128.00 shall be deducted from BOQ on account of schedule of credit Please Enable Macros to View BoQ information |
AI Tender Summary
Tender Timeline
Jul 08, 2026
11:30 IST
Tender Published
Tender notice published.
CompletedJul 29, 2026
17:00 IST
Bid Submission Deadline
Online submission via eProcurement portal.
Upcoming · 20 daysJul 31, 2026
Bid Opening Date
Technical bids will be opened and evaluated.
Upcoming · 22 daysTender Documents
Download All (ZIP) ↓
Disclaimer
We takes all possible care for accurate & authentic tender information. However users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender