Tender For Construction Of Phc,Alied Works In Premisses With Electrification By Dismantling Old Phc Building At Nandar, Tq. Paithan, Dist. Chh. Sambhajinagar
Tender Value
4.43 Crore
Estimated cost
Bid Submission
16 Jul 2026
6 days left
EMD
4.43 Lakhs
Bank guarantee accepted
Document Fee
2360
Non-refundable
Tender Type
Online
Tender Overview
Organization
Tender ID
Competition Type
NCB
Bidding Type
Tender
Location / State
Aurangabad → Maharashtra
EMD Exemption
Not Available
Quantity
Not Available
Website
Contact Person
Address
Project Description
Tender for Construction Of Phc,Alied Works In Premisses With Electrification By Dismantling Old Phc Building At Nandar, Tq. Paithan, Dist. Chh. Sambhajinagar
BOQ
| Sl. No. | Item Description |
| 1 | PART A - WORK PORTION |
| 2 | MAIN BUILDING |
| 3 | Excavation for foundation in earth, soil of all types, sand, gravel and soft murum, including removing the excavated material up to a distance of 50 m. beyond the building area and stacking and spreading as directed, dewatering, preparing the bed for the foundation and necessary back filling, ramming, watering including shoring and strutting etc. complete. (Lift upto 1.5 m.) By Mechanical Means. Bd.A.1 Page 1 Number 259. SSR I.No. 21.02, Sr.No.721, P.No.153 |
| 4 | Ground Floor |
| 5 | Excavation for foundation in earth, soils of all types, sand,gravel and soft murum, including removing the excavated material upto a distance of 50 metres beyond the building area and stacking and spreading as directed, dewatering, preparing the bed for the foundation and necessary back filling, ramming, watering including shoring and strutting etc. complete. (Lift from 1.5m to 3.0m) By Mechanical Means Spec.No.: Bd.A.2 Page 1 Number 259 SSR I.No.21.04, Sr.No.723 P.No.153 |
| 6 | Ground Floor |
| 7 | Filling in plinth and floors with contractors material/brought from outside and approved by Engineer incharge in layers of 15 cm to 20 cm including watering and compaction etc. complete.. Spec. No. Bd.A.11 Page 1 Number 263. SSR I.No. 21.37, Sr.No. 751, P.No. 157 |
| 8 | Ground Floor |
| 9 | Conveying materials obtained from road cutting including all lifts, laying in layers of 20cm to 30cm. breaking clods, dressing to the required lines, curves, grades and section, watering and compacting to not less than 97% of standard Proctor density for a lead of over 50m. to 300m. inclusive from the site of excavation to the site of deposition as directed. Spec. No. MORTH 305 SSR I.No. 2.25, Sr.No. 98 P.No.24 |
| 10 | Ground Floor |
| 11 | Providing preconstructional antitermite treatment as per I.S. 6313 (Part-II) by treating the bottom surface and sides of excavation at the rate of 5 litres of emulsion concentrate of 1.0 percent of chlorophyrifos per square meter of surface area covering 10 years guarantee on bond paper...Spec. No. As directed by Engineer in Charge. SSR I.No.21.22, Sr.No.737, P.No.155 |
| 12 | Ground Floor |
| 13 | Providing preconstructional antitermite treatment as per I.S. 6313 (Part-II) treatment by treating the backfill in immediate contact with foundation at the rate of 5 litres of emulsion concentrate of 1.0 percent of clorophyrifos per One Square Metre of verticalsurface area covering 10 years guarantee on bond paper.. Spec. No. As directed by Engineer in harge. SSR I.No.21.23, Sr.No.738 P.No.155 |
| 14 | Ground Floor |
| 15 | Providing preconstructional antitermite treatment as per I.S. 6313 (Part-II) by treating the top surface of plinth filling at the rate of 5 litres of emulsion concentrate at 1.0 percent of clorophyrifos per One Square Metre of surface area covering ten years guarantee on bond paper... Spec. No. As directed by Engineer in harge. SSR I.No.21.24, Sr.No.739 P.No.156 |
| 16 | Ground Floor |
| 17 | Providing preconstructional antitermite treatment as per I.S. 6313 (Part-I) to the soil along the external face of building by punching holes of 1.2 of 1.5 C.M. diametre about 30 -60 cm deep at 15 cm c/c as close to the wall as possible and to inject 0.5 percent of aldrin or clorophyrifos at the rate of 7.5 litres per hole and sealing the same with proper filling and covering 10 years guarantee on bond paper... Spec. No. As directed by Engineer in harge. SSR I.No.21.25, Sr.No.740 P.No.156 |
| 18 | Ground Floor |
| 19 | Providing soling using 80 mm size trap metal in 15 cm. layer including filling voids with Crushed sand/grit, ramming, watering etc. complete.. Spec. No. As directed by Engineer in charge. SSR I.No. 21.40, Sr.No. 754, P.No. 157 |
| 20 | Ground Floor |
| 21 | Providing and laying Cast in situ/Ready Mix cement concrete in M-10 of trap/ granite/ quartzite/ gneiss metal for foundation and bedding including bailing out water, Steel centering, formwork, laying/pumping, compacting, roughening them if special finish is to be provided, finishing if required and curing complete, with fully automatic micro processor based PLC with SCADA enabled reversible Drum Type mixer/concrete Batch mix plant (Pan mixer) etc. complete. With fine aggregate (Crushed sand VSI Grade) Spec. No. Bd.E.1 Page 1 No. 287.SSR I.No.24.01, Sr.No.827, P.No.175 |
| 22 | Ground Floor |
| 23 | Providing and laying Cast in situ/Ready Mix cement concrete in M15 of trap/ granite/quartzite/gneiss metal for bed blocks, foundation blocks and such other items including bailing out water, Steel centering, formwork, laying/ pumping, compacting, roughening them if special finish is to be provided, finishing uneven and honeycombed surface and curing etc. complete. The Cement Mortar 1:3 plaster is considered for rendering uneven and honeycombed surface only. Newly laid concrete shall be covered by gunny bag, plastic, tarpaulin etc. (Wooden centering will not be allowed.), with fully automatic micro processor based PLC with SCADA enabled reversible Drum Type mixer/ concrete Batch mix plant (Pan mixer) etc. complete. With fine aggregate (Crushed sand VSI Grade) Sepc. No. Bd.E.4 Page Number 289 and B7, Page Number38. SSR I.No. 24.08, Sr.No. 830, P.176 |
| 24 | Ground Floor |
| 25 | Providing and laying Cast in situ/Ready Mix cement concrete M-15 of trap/ granite/quartzite/gneiss metal for coping to plinth or parapet, moulded or chamfered as per drawing or as directed including steel centering, plywood/ steel formwork compacting, roughening them if special finish is to be provided, finishing uneven and honeycombed surface and curing etc. complete. The Cement Mortar 1:3 plaster is considered for rendering uneven and honeycombed surface only. Newly laid concrete shall be covered by gunny bag, plastic, tarpaulin etc. (Wooden centering will not be allowed.) With fine aggregate (Crushed sand VSI Grade) Spec No. : Bd.E. 3/ Page No.288/ I.S. 456 (2000).SSR I.No.24.16, Sr.No.835, P.No.177 |
| 26 | Ground Floor |
| 27 | Providing and laying Cast in situ/Ready Mix cement concrete M-25 of trap / granite/quartzite/ gneiss metal for R.C.C. work in foundations like raft, strip foundations, grillage and footings of R.C.C. columns and steel stanchions etc. including bailing out water, Steel centering, formwork ,cover blocks, laying/pumping, compaction and curing roughening the surface if special finish is to be provided (Excluding reinforcement and structural steel) etc. complete, with fully automatic micro processor based PLC with SCADA enabled reversible Drum Type mixer/ concrete Batch mix plant (Pan mixer) etc. complete. With fine aggregate (Crushed sand VSI Grade) Spec. No.Bd.F.3 Page 1 No. 298 and B.7, Page No.38. SSR I.No.25.13, Sr.No.837 P.No.178 |
| 28 | Ground Floor |
| 29 | Providing and laying Cast in situ/Ready Mix cement concrete M-25 of trap / granite /quartzite/ gneiss metal for R.C.C. columns as per detailed designs and drawings or as directed including steel centering, formwork, cover blocks, laying/pumping, compaction finishing the formed surfaces with cement mortar 1:3 of sufficient minimum thickness to give a smooth and even surface or roughening if special finish is to be provided and curing etc. complete,(Excluding reinforcement and structural steel).with fully automatic micro processor based PLC with SCADA enabled reversible Drum Type mixer/ concrete Batch mix plant (Pan mixer) etc. complete. With fine aggregate (Crushed sand VSI Grade) Spec. No. : Bd.F.5 Page No. 300 and B.7, Page.No. 38.SSR I.No.25.33, Sr.No.842, P.No.180 |
| 30 | Ground Floor |
| 31 | Providing and laying Cast in situ/Ready Mix cement concrete in M-25 of trap/ granite/ quartzite/ gneiss metal for R.C.C. beams and lintels as per detailed designs and drawings or as directed including steel centering, formwork, cover blocks, laying/pumping, compactionand roughening the surface if special finish is to be provided and curing etc. complete. (Excluding reinforcement and structural steel).with fully automatic micro processor based PLC with SCADA enabled reversible Drum Type mixer/ concrete Batch mix plant (Pan mixer) etc. complete. With fine aggregate (Crushed sand VSI Grade) Spec. No. :Bd.F.6 Page Number 300 and B.7, Page 1 Number38 Page.No. 38.SSR I.No.25.52, Sr.No.847, P.No.181 |
| 32 | Ground Floor |
| 33 | Providing and laying Cast in situ/Ready Mix cement concrete M-25 of trap/ granite / quartzite/ gneiss metal for R.C.C. slabs and landings as per detailed designs and drawings including steel centering, formwork, cover blocks, laying/pumping, compaction finishing the formed surfaces with cement mortar 1:3 of sufficient minimum thickness to give a smooth and even surface or roughening if special finish is to be provided and curing etc. complete,(Excluding reinforcement and structural steel).with fully automatic micro processor based PLC with SCADA enabled reversible Drum Type mixer/ concrete Batch mix plant (Pan mixer) etc. complete. With fine aggregate (Crushed sand VSI Grade) Spec No.Bd.F.8 Page No. 302 and B.7, Page1 No.38. SSR I.No.25.72, Sr.No.852 P.No.182 |
| 34 | Ground Floor |
| 35 | Providing and laying Cast in situ/Ready Mixcement concrete M-25 of trap/ granite/ quartzite/ gneiss metal for R.C.C. chajja as per detailed design and drawings including steel centering, formwork, cover blocks, laying/pumping, compacting and roughening the surface if special finish is to be provided and curing complete. (Excluding reinforcement and structural steel). with fully automatic micro processor based PLC with SCADA enabled reversible Drum Type mixer/ concrete Batch mix plant (Pan mixer) etc. complete. With fine aggregate (Crushed sand VSI Grade) Spec.No. Bd.F.9 Page 1 No. 303 and B.7, Page No.38.SSR I.No.26.07, Sr.No.857, P.No.184 |
| 36 | Ground Floor |
| 37 | Providing and laying Cast in situ/Ready Mix cement concrete M-25 of trap / granite / quartzite / gneiss metal for R.C.C. canopy as per detailed designs and drawings including steel centering, formwork, laying/pumping, compacting and roughening the surface if special finish is to be provided and curing etc. complete (excluding reinforcement). with fully automatic micro processor based PLC with SCADA enabled reversible Drum Type mixer/ concrete Batch mix plant (Pan mixer) etc. complete. With fine aggregate (Crushed sand VSI Grade) Spec. No. Bd.F.8 Page 1 No. 303 and B.7, Page No.38 SSR I.No.26.11, Sr.No.859 P.No.184 |
| 38 | Ground Floor |
| 39 | Providing and laying Cast in situ/Ready Mix cement concrete in M-25 of trap/ granite/ quartzite/ gneiss metal for R.C.C. pardi of required thickness including steel centering, formwork, cover blocks, laying/pumping, compacting and roughening them if special finish is to be provided and curing complete. (Excluding reinforcement and structural steel).with fully automatic micro processor based PLC with SCADA enabled reversible Drum Type mixer/ concrete Batch mix plant (Pan mixer) etc. complete. With fine aggregate (Crushed sand VSI Grade) Spec. No. Bd.F.11 Page 1 No. 304 and B.7, Page No. 38.SSR I.No.26.19, Sr.No.861, P.No.185 |
| 40 | Ground Floor |
| 41 | Providing and laying Cast in situ/Ready Mix cement concrete in M-25 of trap / quartzite/granite /gneiss metal for R.C.C. Waist slab, and steps of staircases as per detailed design and drawings or as directed including steel centering, plywood/ steel formwork, steel props, laying/pumping, compaction, finishing uneven and honeycombed surface with C.M. 1:3 of sufficient minimum thickness to give a smooth and even surface or roughening the surface if special finish is to be provided and curing etc. complete. (Excluding einforcement, including cover block).(Newly laid concrete shall be covered by gunny bag, plastic, tarpaulin etc.) with fully automatic micro processor based PLC with SCADA enabled reversible Drum Type mixer/ concrete Batch mix plant (Pan mixer) etc. complete. With fine aggregate (Crushed sand VSI Grade) Spec.No.Bd. F. 13 Page No. 305 / I.S. 456 (2000..SSR I.No.26.26, Sr.No.864, P.No.186 |
| 42 | Ground Floor |
| 43 | Providing and fixing in position TMT - FE - 500 bar reinforcement of various diameters for R.C.C. pile caps, footings, foundations, slabs, beams columns, canopies, staircase, newels, chajjas, lintels pardis, copings, fins, arches etc. as per detailed designs, drawings and schedules. including cutting, bending, hooking the bars, binding with wires or tack welding and supporting as required complete.. Spec.No. Bd.F.17, Page 1 No. 306. SSR I.No.26.33, Sr.No.871, P.No.188 |
| 44 | Ground Floor |
| 45 | Providing and fabricating structural steel work in rolled sections like joists, channels, angles, tees etc. as per detailed design and drawings or as directed including cutting, fabricating, hoisting, erecting, fixing in position making riveted / bolted /welded connections without connecting plates, braces etc. and including one coat of anticorrosive paint and over it two coats of oil painting of approved quality and shade etc. complete.. Spec. No. Bd.C.2 Page 1 Number 275 SSR I.No.23.01, Sr.No.816, P.No.173 |
| 46 | Ground Floor |
| 47 | Providing fly ash brick masonry with conventional / I.S. type fly ash bricks in C.M. 1:6 in foundation and plinth including bailing out water manually striking joints, racking out joints watering and scaffolding etc. complete..Spec. No. As director by engineer in charge and BDG- 2 and 5. SSR I.No.27.12, Sr.No.899 P.No.198 |
| 48 | Ground Floor |
| 49 | Providing fly ash brick masonry with conventional/ I.S. type bricks in cement mortar 1:6 in superstructure including striking joints, raking out joints, watering and scaffolding etc. Complete. Spec. No. As director by engineer incharge and BDG- 2 and 5. SSR I.No.27.13, Sr.No.900 P.No.198 |
| 50 | Ground Floor |
| 51 | Providing Second class fly ash brick masonry with conventional / I.S. type bricks in cement mortar 1:4 in half brick thick wall including mild steel longitudinal reinforcement of two bars of 6 mm diameter / two hoop iron strips 25 mm x 1.60 mm at every third course, properly bent and bounded at ends scaffolding raking out joints and watering etc. complete. Spec. No. Bd. G. 7 Page 316. SSR I.No.27.14, Sr.No.901 P.No.198 |
| 52 | Ground Floor |
| 53 | Providing cement based water proofing treatment to terraces (Indian water proofing or alike) with brick bats laid in required slope to drain the water for any span after cleaning the base surface. Applying a coat of cement slurry admixed with approved water proofing compound and laying the brick bats on bottom layer in C.M.1:5 admixed with approved water proofing compound filling up to half depth of brick bats, curing this layer for 3 days, applying cement slurry over this layer joints of brick bats with C.M.1:3 admixed with approved water proofing compound and finally top finishing with average 20 mm. thick layers of same mortar added with jute fiber at 1Kilogramper bag including finishing the surface smooth with cement slurry admixed with approved water proofing compound. Marking finished surface with false squares of 300mm x 300 mm. making the junctions at the parapet rounded and tapered top for required height, with drip mould at the junction of plaster and parapet and curing and covering 10 years Guarantee against leakproofness on Court fee stamp paper of Rs. 500/- including ponding test etc. complete. .Spec. No. : As directed by Engineer in charge. SSR I.No.31.04, Sr.No.940, P.No.205 |
| 54 | Ground Floor |
| 55 | Providing and applying two coats of High Albedo paint having minimum Solar Reflective Index (SRI) 108 (with solar reflectance & thermal emittance tested as per ASTM) C 1549 and ASTM C 1371 respectively, VOC less than 10 cc/gm. The coating thickness and the methodology of application shall strctly as per manufacturer's specifitions and as approved by engineer in charge. Surface preparation includes cleaning with metal wire brush to remove all dust, fungus etc, washing with water all complete.The contractor shall give guarantee for the performance of SRI and also the durabitity of coating, all complete as per direction of Engineer - in- incharge.. Spec. No. : As directed by Engineer in charge. SSR I.No.48.19, Sr.No.1637 P.No.313 (SSR 2022-23 GREEN BUILDING) |
| 56 | Ground Floor |
| 57 | Providing internal cement plaster 12mm thick in single coat in cement mortar 1:5 without neeru finish to concrete or brick surfaces, in all positions including scaffolding and curing etc. complete Spec. No. : Bd.L.4 Page 1 No. 368. SSR I.No.32.03, Sr.No.957, P.No.209 |
| 58 | Ground Floor |
| 59 | Providing internal cement plaster 20mm thick in Single coats in cement mortar 1:5 without neeru finish, to concrete, brick surface, in all positions including scaffolding and curing etc. complete Spec. No. : Bd.L.4 Page 1 No. 368. SSR I.No.32.06, Sr.No.960, P.No.209 |
| 60 | Ground Floor |
| 61 | Providing and applying plaster / wall punning with plaster of paris ( with plaster of paris material) in 10 to 13 millimeter thickness to previously plastered surface / or on newly brick surface( Excluding rough cast plaster ) in all position including preparing and Finishing the surface scaffolding etc.complete.. Spec. No. : Bd.L.4 Page No. 203. SSR I.No.32.30, Sr.No.981, P.No.211 |
| 62 | Ground Floor |
| 63 | Providing sand faced plaster externally in cement mortar using approved screened sand, in all positions including base coat of 15 mm thick in cement mortar 1:4 using waterproofing compound at 1Kilogramper cement bag curing the same for not less than 2 days and keeping the surface of the base coat rough to receive the sand faced treatment 6 to 8 mm thick in cement mortar 1:4 finishing the surface by taking out grains and curing for fourteen days scaffolding etc.complete. Spec. No. : Bd.L.7 Page 1 No. 369. SSR I.No.32.11, Sr.No.963, P.No.209 |
| 64 | Ground Floor |
| 65 | Providing and applying Texture plaster with finishing with texture material of approved make in 3 to 4 millimeter thickness on previously plastered surface, including Plaster Groove 6mm thickness or Tape Grooves 35 to 45 mm thickness or as required, in all position including preparing the surface, scaffolding etc. complete. Spec. No. : Bd.L.7 Page 1 No. 369. SSR I.No.32.32, Sr.No.983, P.No.211 |
| 66 | Ground Floor |
| 67 | Providing and Fixing Processed Stone Cladding on wall surface/ plywood surface. RCC pardi/ Wall and all type of Interior, Exterior Compound wall and Gate etc. of cladding processed stone with material of Processed clay, Wooden chips, Silica sand, Cement, GFRC admixtures, Colour pigments, Fiber up to thick of 230 mm/ 25 mm including scaffolding, fixing of screw, etc. (As directed by Engineer in Charge) Spec. No. As directed by Engineer-In- Charge. SSR I.No.51.192, Sr.No.2031 P.No.409 |
| 68 | Ground Floor |
| 69 | Providing fine cement finish 1.5 mm thick over green plaster surface including scaffolding curing etc. complete. . Spec. No. : As directed by Engineer in charge. SSR I.No.32.21, Sr.No.972, P.No.210 |
| 70 | Ground Floor |
| 71 | Providing patti/ band 75mm wide on plastered surface 12 mm to 15 mm thick in C.M. 1:3 line and level including neat finishing scaffolding curing etc. complete. . Spec. No. Bd.L. Page No. SSR SSR I.No.32.23, Sr.No.974, P.No.210 |
| 72 | Ground Floor |
| 73 | Providing patti/ band 100mm wide on plastered surface 12 mm to 15 mm thick in C.M. 1:3 line and level including neat finishing scaffolding curing etc. complete. Spec. No. As directed by Engineer in charge. SSR I.No.32.24, Sr.No.975, P.No.210 |
| 74 | Ground Floor |
| 75 | Providing patti/ band 150mm wide on plastered surface 12 mm to 15 mm thick in C.M. 1:3 line and level including neat finishing scaffolding curing etc. complete. Spec. No. : As directed by Engineer in charge. SSR I.No.32.25, Sr.No.976, P.No.210 |
| 76 | Ground Floor |
| 77 | Providing and fixing chicken mesh of 22 gauge, with about 30 cm. width at the junction of R.C.C members and brick work, of approved quality including fixing mesh in position by necessary drilling in concrete /B.B.masonry and or tying by binding wire etc. complete. Spec No.: As directed by Engineer in charge. SSR I.No.32.26, Sr.No.977, P.No.210 |
| 78 | Ground Floor |
| 79 | Providing and applying Two coats of wall care Putty on plastered surface and Ceiling and Walls to prepare surface even and smooth of approved make, etc complete.. Spec No.: As directed by Engineer in charge. SSR I.No.32.34, Sr.No.985, P.No.212 |
| 80 | Ground Floor |
| 81 | Providing and fixing false ceiling with eco-friendly light-weight calcium silicatetiles of spintone surface texture aerolite make or equivalent of size 595mm x 595mm having 15mm thick densified micro look edge and 100% humidity resistance incombustible as per BS 46part IV and thermal conductivity 0.043 w/m 0 KC and NRC 0.50 placed in true horizontal level suspended grid of size 600x600mm made from hot dipped G.I. steel sections ion silhouette profile, rotary stitched double webbed white with 6mm reveal profile (white/black), wherein, main T runner of size 42mmx14mm between main tee 600mm center-tocenter and secondary cross T of size 33x14x0.43mm thick of length 600mm long spaced inter-locked at middle of the first crossed T in each panel to form grid of 1200mmx600mm resting on periphery wall Profile wall section 19mm (7+7) x 19mmx0.40thicknesses and laying false ceiling for services like diffusers grills including cutting, making opening for light fittings, fixtures, , smoke detectors etc., wherever required. Main T runners suspended from ceiling with using G.I. soffit cleats of size 25x35x1.6 mm of required length fixed to the ceiling with 6mm dia and 50mm long dash fastener, 4mm dia G.I. adjustable rods with powder- coated/good quality G.I. level adjustment clips of 35x35x0.8mm spaced @1200, center-tocenter along main T all complete at all heights as per the specifications, drawings and as per Spec.No. As Directed By Engineer in charge. SSR I.No.38.40, Sr.No.1180, P.No.238 |
| 82 | Ground Floor |
| 83 | Providing and fixing in position Gypsum board false ceiling with 12.5 mm thick Gypsum boards, screwed/fixed to the under structure of suspended G.I. Grid constructed and suspended from the main ceiling consisting of ceiling sections of size 25 x 50 mm maximum center to center distance of 600 milimetre perimeter channel and intermediate channels at maximum center to center distance 1200 milimetre galvanized grid should be fixed to reinforced cement concrete slab. The gypsum board should be fixed to galvanized iron grid with necessary screws. The boards should be taped and filled from underside to give smooth, seamless ceiling. The rate should include necessary additional ceiling sections and intermediate channels. Additional intermediate channels should be fixed to strap hangers for additional support to prevent strapping at every 1200 milimetre item to be completed in all respect including necessary sleeves for ducts finishing of joints cut outs, painting including labour, material, lifts etc. all complete. Spec.No. As Directed By Engineer in charge. SSR I.No.38.51, Sr.No.1191, P.No.243 |
| 84 | Ground Floor |
| 85 | Providing groove to required size at specified location as directed by Engineer, at junction of brick masonry wall and R.C.C beams or Column, at junction of composite masonry, including scaffolding, finishing, curing etc. complete. Spec. No. As directed by Engineer in charge. SSR I.No.32.37, Sr.No.987, P.No.212 |
| 86 | Ground Floor |
| 87 | Providing and laying vitrified rustic matt stone finish tiles having size 590 mm to 605 mm x 590 mm to 605 mm of 8 to 10mm thickness and confirming to IS. 15622-2006 (Group Bla) of approved make, shade and pattern for flooring in required position laid on a bed of 1:4 cement mortar including neat cement float, filling joints, curing and cleaning etc. complete. Spec. No. Bd.M.12 Page One Number 385. SSR I.No.33.44, Sr.No.1031 P.No.217 |
| 88 | Ground Floor |
| 89 | Providing and laying vitrified mirror / glossy finish tiles having size 590 mm to 605 mm x 590 mm to 605 mm of 8 to 10 mm thickness and confirming to IS. 15622-2006 ( group Bla) of approved make, shade and pattern for dado and skirting in required position fixed in 1:4 cement mortar including neat cement float, filling joints, curing and clearing etc. complete Spec. No. Bd.M.12 Page 1 No. 385. SSR I.No.33.41, Sr.No.1028 P.No.217 |
| 90 | Ground Floor |
| 91 | Providing and laying Vitrified MATT finish having decorative type of size 1000 millimeter x 1000 millimeter of 8 to 10 millimeter thickness (on a existing flooring) with bonding chemical and confirming to IS 15622-2006 (Group Bla) of approved make shade and pattern for flooring in required position laid on a bed of bonding chemical filling joints curing and cleaning etc .complete. Spec. No. Bd.M.12 Page No. 385. SSR I.No.33.61, Sr.No.1047 P.No.220 |
| 92 | Ground Floor |
| 93 | Providing and laying cement concrete flooring 40mm thick with M20 cement concrete laid to proper level and slope in alternate bays, including compaction, filling joints, marking lines to give appearance of tiles of 30cm x 30cm or other size laid diagonally/square etc. finishing smooth (with extra cement) in any colour as directed and Curing etc. complete. With Crushed sand VSI Grade Spec. Nos. : Bd.M.6 Page One Number 381. SSR I.Nos.33.12, Sr.Nos.999, P.Nos.214 |
| 94 | Ground Floor |
| 95 | Providing and laying ceramic tiles having size 30 cm. x 60 cm. confirming to corresponding I.S. for dado and skirting in required position with readymade adhesive mortar of approved quality on plaster of 1:2 cement mortar including joint filling with white/ colour cement slurry cleaning curing etc. complete. Spec. No. : Bd.M.13 Page One Number 386..SSR I.No.33.27, Sr.No.1014 P.No.215 |
| 96 | Ground Floor |
| 97 | Providing and laying Antiskid Ceramic tiles of approved quality of size 30 cm x 30 cm and confirming to IS 15622-2006 (Group-B IIA) for antiskid flooring in required position laid on a bed of 1:4 cement mortar including cement float, filling joint with cement slurry cleaning curing etc. complete.. Spec. No. :Bd. M-12 page 1 No. 385.SSR Item I.No.33.67, Sr.No.1051, P. No. 220 |
| 98 | Ground Floor |
| 99 | Providing and laying machine cut machine Polished Kota stone flooring 25mm to 30mm thick and required width in plain/ diamond pattern on bed of 1:6 C. M. including cement float, filling joints with neat cement slurry, curing, polishing and cleaning etc. complete.. Spec. No. Bd.M.3 Page 1 No.380.SSR I.No.33.06, Sr.No.993 P.No.213 |
| 100 | Ground Floor |
| 101 | Providing Mirror polishing to Kota Stone including using all necessary stones and equipments cleaning, washing etc. complete. For Flooring Spec. No. As directed by Engineer in charge. SSR I.No.33.28, Sr.No.1015 P.No.216 |
| 102 | Ground Floor |
| 103 | Providing and laying machine cut machine polished machine cut Kota stone slabs 20 to 25 mm thick for treads and risers of steps and staircases, with rounded nosing for the treads on a bed of 1:4 cement mortar including cement float, filling joints with neat cement slurry, curing, polishing and cleaning etc. complete.. Spec No.:As directed by Engineer in charge. SSR I.No.33.18, Sr.No.1005, P.214 |
| 104 | Ground Floor |
| 105 | Providing and laying in position flooring of Sira Gray / Kashmir white granite stone as approved by Architect / Engineer Incharge / Chief Engineer etc. of approved shade and size 18 mm to 20 mm thick on bed 1:6 cement mortar including cement floats striking joints, pointing in C.M. 1:3 curing and cleaning etc. complete... Spec. No. Bd.M. 3 B/Page Number 380. SSR I.No.33.34, Sr.No.1021 P.No.216 |
| 106 | Ground Floor |
| 107 | Providing and fixing machine cut machine polished 18 mm to 20 mm thick Sira Gray / Kashmir white granite stone as approved by Architect / Engineer Incharge / Chief Engineer etc. for treads and risers of steps and staircases of approved colour and shade with full moulding and three grooved line for the treads on bed of 1:4 Cement mortar including float filling joints with neat cement slurry curing polishing and cleaning etc. complete.. Spec No.:Bd. M.22 B/Page Number 390. SSR I.No.33.35, Sr.No.1022, P.216 |
| 108 | Ground Floor |
| 109 | Providing and laying Sira Gray / Kashmir white granite stone as approved by Architect / Engineer Incharge / Chief Engineer etc.granite stone of 18 to 20 mm thick for door frame/ dado/ window boxing etc. On C.M. 1:6 including filling joints with polymer base filler nosing/moulding the sharp edges wherever necessary, curing, etc. complete..Spec. No. As directed by Engineer-In- Charge. SSR I.No.33.68, Sr.No.1052 P.No.220 |
| 110 | Ground Floor |
| 111 | Providing and laying chequered tiles of approved quality of size 30 cm x 30 cm, confirming to corresponding I.S. for flooring in required position laid on a bed of 1:4 cement mortar including cement float, filling joint with cement slurry cleaning curing etc. complete.. Spec No.:Bd. M-12 page Number 385. SSR I.No.33.66, Sr.No.1050, P.220 |
| 112 | Ground Floor |
| 113 | Providing and constructing granite kitchen platform with fixing of stainless steel sink 600 mm x 450 mm size as per detailed drawing including vertical both side polished kadappah stone 25 to 30 mm thick supports with kadappah top 35 to 40 mm thick and polished granite 16 to 20 mm top with side strips of granite at front and both sides of platform raised with two vertical granite supports 15 cm height and top granite of 75 x 40 cm including cutting, opening for sink of required size in kadappah as well as granite etc. complete. (Platform top size 5.00 m x 0.60 m and height is 0.75 m) Spec. No. As directed by Engineer-In- Charge. SSR I.No.41.78, Sr.No.1369 P.No.273 |
| 114 | Ground Floor |
| 115 | Providing and applying priming coat on concrete/ masonary/ Asbestos Cement plastered surfaces including scaffolding if necessary, preparing the surface by thoroughly cleaning oil, grease, dirt and other foreign matter and sand papering as required etc. complete.. Spec. No. : As directed by Engineer in charge. SSR I.No.35.21, Sr.No.1090 P.No.225 |
| 116 | Ground Floor |
| 117 | Providing and applying washable oil-bound distemper of approved colour and shade to old and new surfaces in two coats including scaffolding, preparing the surfaces. (excluding the primer coat.) etc. complete.Spec. No. : Bd.P.5 Page No. 413. SSR I.No.36.11, Sr.No.1106 P.No.227 |
| 118 | Ground Floor |
| 119 | Providing and applying plastic emulsion paint of approved quality, colour and shade to new surface in three coats including scaffolding, preparing the surface. (excluding primer coat) etc. complete. as directed by Engineer in charge.Spec. No. : Bd.P.6 Page One Number 414 and Preapproval of Superintending Engineer SSR I.No.36.14, Sr.No.1109, P.No.228 |
| 120 | Ground Floor |
| 121 | Providing and applying two coats of exterior acraylic emulsion paint confirming to corresponding I.S. of approved manufacture and of approved colour to the plastered surfaces including cleaning ,preparing the plaster surface, applying primer coat,scaffolding if necessary , and watering the surface for two days etc complete. Spec. No. : As directed by Engineer in charge. SSR I.No.35.25, Sr.No.1631, P.No.225 |
| 122 | Ground Floor |
| 123 | Providing and fixing frame with / without ventilator of size as specified with Country cut teak wood for doors and windows including chamfering, rounding, rebating, iron holdfast of size 300mm x 40mm x 5mm with oil painting, etc. complete Spec.No.As directed by Engineer in charge. SSR I.No.39.01, Sr.No.1194 P.No.245 |
| 124 | Ground Floor |
| 125 | Providing and fixing Country cut teak wood double or single leaf panelled shutters, 35 mm thick style top and freze rail 95 x 35 thick with lock and bottam rail 195 x 25 mm thick and panels without ventilator as per detailed drawing excluding the door frame, stainless steel fixtures and fastening and finishing the wood work with oil painting 3 coats complete. Spec.No. BD-T-11 and 12 Page Number 482-83. SSR I.No.39.08, Sr.No.1201 P.No.246 |
| 126 | Ground Floor |
| 127 | Providing and fixing 34 mm thick moulded door shutter consisting of solid core single leaf flush door of 30 mm thickness lipped with 15 mm ( 5mm x 3) thick x 30 mm width on one style and top rail and 10 mm (5mm x 2) thick x 30 mm width on other style and bottom rails. The inner panels laminated with 2 mm thick termite proof, water proof and fire resistant moulded PVC sheet with 2,4,6 design in different plain and /or prelim colours on one side after routing the moulded design on flush doors and 2 mm plain and /or pre lam PVC on other side using rubber adhesive on flush door and solvent cement adhesive on the PVC lipping etc. as per direction of Engineer in charge and manufacturers specification and drawing etc. complete.. Spec. Nos. BD-T-34 Page Nos. 499. SSR I.Nos.39.48, Sr.Nos.1241 P.Nos.256 |
| 128 | Ground Floor |
| 129 | Providing and fixing in position powder coated aluminium louvered windows / ventilator of various sizes with powder coating as per detailed drawing and specifications including aluminium frames 80 x 38 mm x 1.22 mm box type, 5 mm thick sheet glass louvers, of approved quality etc. complete..Spec. No. : As directed by Engineer in charge. SSR I.No.39.68, Sr.No.1263 P.No.259 |
| 130 | Ground Floor |
| 131 | Providing and Fixing 30 MM thick BOTH SIDE PRELAMINATED SOLID PANEL PVC DOOR SHUTTER consisting of frame made out of M.S tubes of 19 guage thickness and, size 19 x 19 mm for styles and 15 x15 mm for the top and bottom rails, M.S frame shall have a coat of metel primer of approved make and manufacture. M.S frame shall be covered with heat mouled PVC 'C' channel made from 5 mm (+/0.25) thick prelaminated sheet of density 600 Kilogram/cbm ,of size 30mm thickness 70mm width out of which 50mm shall be flat and 20mm shall be tapered in 45? angle on either side forming stiles ; and 5 mm thick ,95 mm wide PVC sheet out of which 75 mm shall be falt and 20 mm shall be tapered in 45 on the inner side to form top and bottom rail and 115 mm wide PVC sheet out of which 75 mm shall be falt and 20 mm shall be tapered on both sides to form lock rail.Top,bottom and lock rail shall be provided either side of the panel. An additional 5 mm (+/0.25) thick PVC strip of 20 mm width is to be stuck on the bottom side of the ' c ' channel prelaminated paneling of 5 mm (+/0.25) thick PVC sheet to be fitted inside the M.S. frame welded/ sealed to the styles and rails with 5 mm (+/0.25) x 30 mm PVC sheet beading on either side and joined together with solvent cement adhesive etc ,10 mm thickness (5 mm (+/0.25) x 2 nos ) 20 mm wide cross PVC sheet as gap insert for the rail and bottom rail. Door to be fixed to frames with 3 nos M.S.powder coated but hinges of size 100 mm x 25MM x 2mm using 32 mm long steel screws drilled suitable to pass through both the walls of the M.S tube. Other hardwares Spec. No. : As directed by Engineer in charge. SSR I.No.39.47, Sr.No.1240 P.No.255 |
| 132 | Ground Floor |
| 133 | Providing and fixing in position. (as per I.S.1868 / 1982) Aluminium sliding window of two tracks with rectangular pipe having overall dimension ?63.50 x 38.10 x 1.02 mm at weight 0.547 Kilogram/One Running Metre. and window frame bottom track section 61.85 x 31.75 x 1.20 mm at weight 0.695 Kilogram/One Running Metre. Top and side track section 61.85 x 31.75 x 1.30 mm at weight 0.659 Kilogram/One Running Metre. The shutter should be of bearing bottom 40 x 18 x 1.25 mm at weight 0.417 Kilogram/One Running Metre. Inter locking section 40 x 18 x 1.10 mm at weight 0.469 Kilogram/One Running Metre. And handle section 40 x 18 x 1.25 mm at weight 0.417 Kilogram/One Running Metre. and top section 40 x 18 x 1.25 mm at weight 0.417 Kilogram/Running metre. As per detailed drawings and as directed by Engineer in charge with all necessary Aluminium sections fixtures and fastenings such as roller bearing in nylon casting and self locking catch fitted in vertical section of shutter including 5 mm thick plain glass with all required screws and nuts etc, complete. With powder coating without box Spec. No. : As directed by Engineer in charge..SSR I.No.39.40, Sr.No.1233, P.No.252 |
| 134 | Ground Floor |
| 135 | Providing and fixing in position (as per 1868 / 1982) Aluminium sliding window of three tracks with rectangular pipe 95 x 38.10 x 0.90 mm at weight 0.637 Kilogram/One Running Metre. with window frame bottom track section 92 x 31.75 x 1.30 mm at weight 1.070 Kilogram/One Running Metre.. Top and side track section 92 x 31.75 x 1.30 mm at weight 0.933 Kilogram/Running metre. The shutter should be of bearing bottom 40 x 18 x 1.25 mm at weight 0.417 Kilogram/One Running Metre. Inter locking section 40 x 18 x 1.10 mm at weight 0.469 Kilogram/Running metre. and handle and top section 40 x 18 x 1.25 mm at weight 0.417 Kilogram/Running metre. As per detailed drawings and as directed by Engineerincharge with all necessary Aluminium sections fixtures and fastenings such as roller bearing in nylon casting and self locking catch fitted in vertical section of shutter including 5 mm thick plain glass and aluminium mosquito net shutter with stainless steel jail with all required screws and nuts etc, complete. With powder coating without box Spec. No. : As directed by Engineer in charge. SSR I.No.39.44, Sr.No.1237 P.No.254 |
| 136 | Ground Floor |
| 137 | Providing and fixing mild steel grill work for windows, ventilators, etc. 15 Kilogram/ One Square Metre as per drawing including fixtures necessary welding and painting with one coat of anticorrosive paint and two coats of oil painting complete. Spec. No. : Bd.U. 1 Page No. 537. SSR I.No.40.02, Sr.No.1292 P.No.264 |
| 138 | Ground Floor |
| 139 | Providing and Fixing mat finish stainless steel (of 302 grade ) railing with top pipe of 50 mm dia. and vertical pipe of 38 mm dia at 0.60 m c/c or as required and horizontal pipes of 25 mm dia in three rows, all pipes of 2 mm thick including buffing,fabricating fixtures and fastening including pipe base of appropriate diameter and ball base of 75 mm dia above newel post of 75 mm diameter etc. complete (Prior approval of sample and brand by Ex.Engineer is necessary before use) Spec No.:As directed by Engineer Incharge.SSR I.No.40.08, Sr.No.1298 P.No.265 |
| 140 | Ground Floor |
| 141 | Providing and fixing C.P. 2 Way BIB cock with wall flange of approved make including necessary sockets/ union nut etc. complete as directed by Engineer in charge. SSR I.No.48.27, Sr.No.1644, P.No.314 (SSR 2022-23 GREEN BUILDING) (Jaquar / Equivalent make Confirming Green Bldg Certificate) |
| 142 | Ground Floor |
| 143 | Providing and fixing 15 mm dia. screw down bib/ stop tap of brass including necessary socket union nut complete. Spec. No.: Bd.V. 8 Page No. 554..SSR I.No.41.40, Sr.No.1334, P.No.270 |
| 144 | Ground Floor |
| 145 | Providing and fixing push cock (Self closing tap) symet type of 15 mm dia. including necessary socket, testing etc. complete. Spec No.:As directed by Engineer in charge. SSR I.No.41.54, Sr.No.1348, P.No.271 (Jaquar / Equivalent make Confirming Green Bldg Certificate) |
| 146 | Ground Floor |
| 147 | Providing and fixing White glazed with bottle trap earthenware Wash Hand Basin of 63x45 cm size including cold water piller taps, brackets, rubber plugs and brass chain, stop tap, chromium plate bottle trap and necessary pipe connections including UPAC waste pipe and trap upto the outside face of the wall, making good the damaged surface, testing etc. complete. BDV.-30 Page Number616. SSR I.No.41.70, Sr.No.1363 P.No.272 (Jaquar / Equivalent make Confirming Green Bldg Certificate) |
| 148 | Ground Floor |
| 149 | Providing and fixing Oval Type Under Counter Wash Hand Basin of 420 x 590 x 195mm size with pillar cock, C.P.Angular stop cock, long thread of approved make continental including SS bottle trap of necessary pipe connection up to the outside face of the wall, having Telephonic Black / Colour Granite of 180 mm thick fixed on Black Kadappa Framework, etc. Complete as directed by Engineer in charge.. SSR I.No.48.35, Sr.No.1651, P.No.315 (SSR 2022-23 GREEN BUILDING) |
| 150 | Ground Floor |
| 151 | Providing and laying concrete pipes of I.S.NP. class of 150mm diameter in proper line, level and slope including necessary collars, excavation, laying, fixing with collars in cement mortar 1:1 and refilling the trench complete.Spec. No. :Bd.V.41, Page No. 573.SSR I.No.42.07, Sr.No.1378 P.No.274 |
| 152 | Ground Floor |
| 153 | Providing and laying concrete pipes of I.S.NP. class of 300mm diameter in proper line, level and slope including necessary collars, excavation, laying, fixing with collars in cement mortar 1:1 and refilling the trench complete.. Spec. No. :Bd.V.41, Page No. 573.SSR I.No.42.09, Sr.No.1380 P.No.274 |
| 154 | Ground Floor |
| 155 | Providing , constructing and fixing 250 mm dia. Inspection chamber made up of UPVC material of thickness 3.5 mm and height of 259 mm with inlet and outlet of 110 mm dia. with 75 mm dia. U Trap, Ultra shaft pipe of Upvc material having height of 470 mm and fixing Ultra 250 mm dia. UPVC cover and frame in 150 mm thick in c.c.1:2:4, having crushed sand bed of 100 mm thick of size 550 mm dia. Including excavation and refilling the sides of chamber by crushed sand cushioning 150 mm thickness, connecting all required UPVC fittings with rubber lubricant etc. complete.. Spec. Nos. : As Directected By Engineer Incharge. SSR I.Nos.43.27, Sr.Nos.1498, P.Nos.290 |
| 156 | Ground Floor |
| 157 | Providing , constructing and fixing 450 mm dia. Inspection chamber made up of Polypropylene / polyethylene material of thickness 3.5 mm and height of 388 mm with 160 or 200 mm main inlet (s) outlet and 110 and / or 160 mm branch inlets, with 450 mm dia. Ultra shaft pipe of HDPE material having height of 460 mm, having R.C.C. cover and frame fixing in 150 mm thick in c.c.1:2:4, having crushed sand bed of 150 mm thick of size 750 mm dia. Including excavation and refilling the sides of chamber by sand crushed cushioning 150 mm thickness, connecting all required UPVC fittings with rubber lubricant etc. complete. Spec. Nos. : As Directected By Engineer Incharge. SSR I.Nos.43.28, Sr.Nos.1499, P.Nos.290 |
| 158 | Ground Floor |
| 159 | Providing and fixing 450mm x 550mm size superior type Belgium mirror with 16mm dia. nickel plated towel rod etc. complete..Spec No.:As directed by Engineer in charge.. SSR I.No.42.20, Sr.No.1391, P.No.276 |
| 160 | Ground Floor |
| 161 | Providing and fixing stainless steel sink of size 600 x 510 x 200 mm incluidng coupling, outlet pipe, elbow and other necessary fitting, finishing etc. complete... Spec No.:As directed by Engineer in charge. SSR I.No.42.78, Sr.No.1449, P.No.282 (Jaquar / Equivalent make Confirming Green Bldg Certificate) |
| 162 | Ground Floor |
| 163 | Providing and fixing C.P. Angular stop clock with wall flange of approved make continental including necessary sockets/union nut etc. complete. Spec No.:As directed by Engineer in charge. SSR I.No.42.79, Sr.No.1450, P.No.282 (Jaquar / Equivalent make Confirming Green Bldg Certificate) |
| 164 | Ground Floor |
| 165 | Providing and fixing C.P. BIB cock with wall flange of approved make including necessary sockets/ union nut etc. complete. Spec No.:As directed by Engineer in charge. SSR I.No.42.83, Sr.No.1454, P.No.283 (Jaquar / Equivalent make Confirming Green Bldg Certificate) |
| 166 | Ground Floor |
| 167 | Providing and fixing C.P. sink cock with raised J\\" shaped swinging casted spout ofapproved make including necessary sockets/ union nut etc. complete.\\" Spec No.:As directed by Engineer in charge. SSR I.No.42.84, Sr.No.1455, P.No.283 (Jaquar / Equivalent make Confirming Green Bldg Certificate) |
| 168 | Ground Floor |
| 169 | Providing and fixing 40 mm. dia Ball cock medium type with PVC float including sockets and necessary fittings and tested as per municipal requirements etc. complete. . Spec No.:As directed by Engineer in charge. SSR I.No.42.36, Sr.No.1407, P.No.277 |
| 170 | Ground Floor |
| 171 | Providing and fixing 15 mm. dia Ball cock medium type with PVC float including sockets and necessary fittings and tested as per municipal requirement etc. complete. Spec No.:As directed by Engineer in charge. SSR I.No.42.37, Sr.No.1408, P.No.277 |
| 172 | Ground Floor |
| 173 | Providing and fixing Shower Head, with shower arm of approved make mixer of including all necessary pipe fittings and connections etc. complete as directed by Engineer in charge. Spec Nos.:As directed by Engineer in charge. SSR I.Nos.48.34, Sr.Nos.1650, P.Nos.315 (Jaquar / Equivalent make Confirming Green Bldg Certificate) |
| 174 | Ground Floor |
| 175 | Providing and fixing C.P. wall mixer with provision for overhead shower with 115mm long bend pipe and wall flange of approved make including necessary sockets/union nut etc. complete. Spec Nos.:As directed by Engineer in charge. SSR I.Nos.42.81, Sr.Nos.1452, P.Nos.282 (Jaquar / Equivalent make Confirming Green Bldg Certificate) |
| 176 | Ground Floor |
| 177 | Providing and fixing Orissa Pan of size 580x445x260 mm with approved make flush valve including trap, C.I. soil and vent pipe upto outside face of wall including 100mm dia. C.I. plug, bend and necessary pipe connection, etc complete. As directed by Engineer in charge.. Spec No. As directed by Engineer in charge. SSR I.No.48.38, Sr.No.1654, P.No.315 (SSR 2022-23 GREEN BUILDING) (Jaquar / Equivalent make Confirming Green Bldg Certificate) |
| 178 | Ground Floor |
| 179 | Providing and fixing white Opal series European type wall-hung, of size 400 mm x 370 mm x 575mm with approved make flush valve including soil pipe, vent pipe upto outside face of wall, 100mm dia C.I. plug bend inlet pipe all fittings, cutting & making good walls, floors etc as directed by Engineer in charge.. Spec No.:As directed by Engineer in charge. SSR I.No.48.37, Sr.No.1653, P.No.315 (SSR 2022-23 GREEN BUILDING) |
| 180 | Ground Floor |
| 181 | Providing and fixing white glazed earthenware lipped flat back/corner type Urinal with PVC 5 liters flushing cistern with fittings, inlet pipe with stop tap, brackets for fixing the cistern, 32 mm diameter P.V.C. flush pipe with fitting including lead soil pipe, lead trap and soil pipe connection up to the outside face of wall.. Spec No.:As directed by Engineer in charge. SSR I.No.41.60, Sr.No.1354, P.No.271 |
| 182 | Ground Floor |
| 183 | Providing and fixing 75 mm dia stabiliser pipe/ P.V.C. soil vent/waste pipe and with necessary fixtures and fitting such as bends, tees, single junctions, slotted vent, clamps etc. complete Spec. No.: As directed by Engineer in charge.SSR I.No.42.51, Sr.No.1422, P.No.279 |
| 184 | Ground Floor |
| 185 | Providing and fixing 100 mm dia stabiliser pipe/ P.V.C. soil vent/waste pipe and with necessary fixtures and fitting such as bends, tees, single junctions, slotted vent, clamps etc. complete.Spec. Nos.: As directed by Engineer in charge.SSR I.Nos.42.52, Sr.Nos.1423, P.Nos.279 |
| 186 | Ground Floor |
| 187 | Providing , laying and fixing ,jointing Eco- drain 110 mm SN 8 Nu- Drain Upvc pipes or of equivalent make, manufacture as per EN 13476 or equivalent as per I.S.15328 with fittings such a bends, tees, coupler, etc, jointing with rubber lubricant including necessary excavation, trench refilling with selective excavated material etc. complete.. Spec. No.: As directed by Engineer in charge.SSR I.No.43.30, Sr.No.1501, P.No.291 |
| 188 | Ground Floor |
| 189 | Providing , laying and fixing ,jointing Eco- drain 160 mm SN 4 Nu- Drain Upvc pipes or of equivalent make, manufacture as per EN 13476 or equivalent as per I.S.15328 with fittings such a bends, tees , coupler, etc, jointing with rubber lubricant including necessary excavation, trench refilling with selective excavated materialetc. complete Spec. No.: As directed by Engineer in charge.SSR I.No.43.31, Sr.No.1502, P.No.291 |
| 190 | Ground Floor |
| 191 | Providing and fixing H.D.P container one piece moulded water tank made out of low density polythyler and built corrugation including of delivery up to destination hoisting and fixing of accessories such as inlet, outlet overflow of all tanks capacity above 1000 to 20,000 litres Spec. No. As directed by Engineer in charge. SSR I.No.42.54, Sr.No.1425, P.No.280 |
| 192 | Ground Floor |
| 193 | Providing and fixing on walls/ ceiling/ floor 15 mm dia. CPVC pipe with necessary fittings, remaking good the demolished portion etc. complete. Including removing existing pipe line if necessary and conveying and stacking the same in PWD chowky or as directed etc. complete..Spec.No.: BD.V 5 page 551 and as directed by Engineer in charge. SSR I.No.42.55, Sr.No.1426, P.No.280 |
| 194 | Ground Floor |
| 195 | Providing and fixing on walls/ceiling/floor 20 mm dia. CPVC pipe with necessary fittings, remaking good the demolished portion etc. complete. Including removing existing pipe line if necessary and conveying and stacking the same in PWD chowky or as directed etc. complete.. Spec. No.: BD.V 5 page 551 and as directed by Engineer in charge. SSR I.No.42.56, Sr.No.1427, P.No.280 |
| 196 | Ground Floor |
| 197 | Providing and fixing on walls/ ceiling/ floor 25 mm dia. CPVC pipe with necessary fittings, remaking good the demolished portion etc. complete. Including removing existing pipe line if necessary and conveying and stacking the same in PWD chowky or as directed etc. complete. Spec.No.: BD.V 5 page 551 and as directed by Engineer in charge. SSR I.No.42.57, Sr.No.1428, P.No.280 |
| 198 | Ground Floor |
| 199 | Providing and fixing on walls/ ceiling/ floor 32 mm dia. CPVC pipe with necessary fittings, remaking good the demolished portion etc. complete. Including removing existing pipe line if necessary and conveying and stacking the same in PWD chowky or as directed etc. complete.. Spec. No.: BD.V 5 page 551 and as directed by Engineer in charge. SSR I.No.42.58, Sr.No.1429, P.No 280 |
| 200 | Ground Floor |
| 201 | Providing and fixing on walls /ceiling/ floor 40 mm dia. CPVC pipe with necessary fittings, remaking good the demolished portion etc. complete. Including removing existing pipe line if necessary and conveying and stacking the same in PWD chowky or as directed etc. complete. Spec.No.: BD.V 5 page 551 and as directed by Engineer in charge .SSR I.No.42.59, Sr.No.1430, P.No.280 |
| 202 | Ground Floor |
| 203 | Providing and fixing on walls/ ceiling/ floor 50 mm dia. CPVC pipe with necessary fittings, remaking good the demolished portion etc. complete. . Spec.Nos.: BD.V 5 page 551 and as directed by Engineer in charge .SSR I.Nos.42.60, Sr.Nos.1431, P.Nos.280 |
| 204 | Ground Floor |
| 205 | Providing and fixing 15 cm rigid PVC Nahani trap including PVC grating ,bend,connectingpiece of UPVC pipe up to the outside face of wall ,making the good damaged surface and testing etc. complete ( Prior approval of sample and brand by Ex. Engr. is necessary before use) Spec. No. BD.V 32 A page 551 and as directed by Engineer in charge. SSR I.No.43.18, Sr.No.1489 P.No.288 |
| 206 | Ground Floor |
| 207 | Providing and fixing P.V.C. Rain water pipes of 160mm outer diameter and having wall thickness of 2.2 to 2.7 mm confirming to I.S. 13592-1992 including proper rainwater receiving recess with P.V.C. plug, bend, necessary fittings, such as, offsets, shoes, inluding fixing the pipe on wall using approved wooden cleats projecting 25mm to 40mm from face of wall a fixing with clips of approved quality and One Number ,filing the joint using rubber gasket with solvent cement and properly resting the shoe of pipes on C.C. or masonry blocks, including necessary scaffolding and maintenance for 3 yrs for any leakages or dislocations of pipes. All the P.V.C. fittings and additional 2 piece socket clips shall be got approved from engineer in charge etc. complete.. Spec No. As directed by Engineer Incharge. SSR I.No.42.85, Sr.No.1456, P.No.283 |
| 208 | Ground Floor |
| 209 | Providing and laying in trenches 15 mm dai. CPVC pipe including necessary excavation, fittings. Refilling trenches etc. complete Including removing existing pipe line if necessary and conveying and stacking the same in PWD chowky or as directed etc. complete... Spec. Nos.: BD.V 5 page 551 and as directed by Engineer in charge. SSR I.Nos.42.61, Sr.Nos.1432, P.Nos.280 |
| 210 | Ground Floor |
| 211 | Providing and laying in trenches 20 mm dai. CPVC pipe including necessary excavation, fittings. Refilling trenches etc. complete. Including removing existing pipe line if necessary and conveying and stacking the same in PWD chowky or as directed etc. complete.. Spec. Nos.: BD.V 5 page 551 and as directed by Engineer in charge. SSR I.Nos.42.62, Sr.Nos.1433, P.Nos.281 |
| 212 | Ground Floor |
| 213 | Providing and laying in trenches 25 mm dai. CPVC pipe including necessary excavation, fittings. Refilling trenches etc. complete. Including removing existing pipe line if necessary and conveying and stacking the same in PWD chowky or as directed etc. complete.. Spec. Nos.: BD.V 5 page 551 and as directed by Engineer in charge. SSR I.Nos.42.63, Sr.Nos.1434, P.Nos.281 |
| 214 | Ground Floor |
| 215 | Providing and laying in trenches 32 mm dai. CPVC pipe including necessary excavation, fittings. Refilling trenches etc. complete. Including removing existing pipe line if necessary and conveying and stacking the same in PWD chowky or as directed etc. complete.. Spec. Nos.: BD.V 5 page 551 and as directed by Engineer in charge. SSR I.Nos.42.64, Sr.Nos.1435, P.Nos.281 |
| 216 | Ground Floor |
| 217 | Providing and laying in trenches 40mm dai. CPVC pipe including necessary excavation, fittings. Refilling trenches etc. complete. Including removing existing pipe line if necessary and conveying and stacking the same in PWD chowky or as directed etc. complete.. Spec. Nos.: BD.V 5 page 551 and as directed by Engineer in charge. SSR I.Nos.42.65, Sr.Nos.1436, P.Nos.281 |
| 218 | Ground Floor |
| 219 | Providing and laying in trenches 50mm dai. CPVC pipe including necessary excavation, fittings. Refilling trenches etc. complete. Including removing existing pipe line if necessary and conveying and stacking the same in PWD chowky or as directed etc. complete.. Spec. Nos.: BD.V 5 page 551 and as directed by Engineer in charge. SSR I.Nos.42.66, Sr.Nos.1437, P.Nos.281 |
| 220 | Ground Floor |
| 221 | Providing and fixing in position UPVC ultra violet stabilized 110 mm outer diameter cowl dome confirming to I.S.-4985 including making joints with solvent cement etc. complete Spec No.:As directed by Engineer in charge. SSR I.No.43.25, Sr.No.1496, P.No.290 |
| 222 | Ground Floor |
| 223 | Providing and fixing Glass self 125 mm wide and 600 mm long with necessary chromium plated brackets providing T.W.gutties etc. complete Spec. No.: As directed by Engineer in charge .SSR I.No.43.26, Sr.No.1497, P.No.290 |
| 224 | Ground Floor |
| 225 | Providing and fixing 90 cm x 60 cm Granite plate engraving 10 cm. height letter,figures including painting the lefters/figures with approved colour and shade complet Spec. No. Bd.W.7 Page No.586. SSR I.No.44.12, Sr.No.1527, P.No.294 |
| 226 | Ground Floor |
| 227 | Providing and fixing lioghtening conductor system comprising of erecting AirTermination consisting of tubular copper rod of 25mm dia. 1.2 mm thick with multiple points head 1.2 mt. long ( Heavy Duty) welded or clamped to G.I. pipe pole B grade 50 mm diaof requiired length with M.S. round bnase plate 25 Cm diam and 10mm thick at bottom embeded in cement concrete 1:3:6 dfoundation of size 45 cm diam x 45 cm Height and providing earthing with copper earth plate of size 60 x 60 x 0.3 cms with cadmium plated nut bolts to fix earthing strip burried in specially prepared earth pits 1.5 metre below ground level with 40Kilogramcharcoal and salt with altemate layers of charcoal and salt and G.I.pipe 40mm dia 2 meter length burried in earthe upto earthling plate remining portion above ground level for watering and refilling comcpete Note- Copper strip fropm lightening conductor is not considered in this item... Spec. Nos.: As directed by Engineer in charge .SSR I.Nos.44.18, Sr.Nos.1533, P.Nos.295 |
| 228 | Ground Floor |
| 229 | Supply, fixing and installation of 4mm thick Aluminium Composite Panel (ACP) of approved colour for external cladding in combination of solid and metallic colours, including all necessary Framework, support and complete weather sealing as per architectural drawing. The Aluminium Composite Panel (ACP) should be made out of thermoplastic core of low-density polyethylene LDPE (100% virgin mix), sandwiched between two aluminium sheets of ALLOY GRADE- 5000 series, each not less than 0.50 mm thick, total thickness of aluminium composite panels not to be less than 4 mm, the exposed surface thereof shall have Stove lacquered finishing coat not less than (26 + - 2) micron (containing minimum 70% kynar 500 based PVDF) of colour and shade as per architectural design. The inside surface (facing the building exterior surface)shall have polyster based powder coating not less than 25 Micron with protective peel-off foil on the exterior face (peel off film will in no case leave any adhesive mark over the composite panel surface after it is peeled off). The supporting framework shall be made out of 50 mm X25mm X 3mm thick Aluminium section to be spaced horizontally and vertically for fixing of panel of size 900 mm X 1200 mm and fixed to the building structure as per design through 50mm X50mm X5 mm MS angle clamps prefixed to masonry or slab, columns with Hilti make anchor fastener screws. The fixing of panel to be done with the help of VHB tapes and screws and all the sealing of joints to be done with weather sealent Silicon as directed by Engineer-in-charge. (Prior permission of S.E. is necessary before inclusion of this item in estimate) Spec. Nos. As directed by Engineer in charge. SSR I.Nos.51.235, Sr.Nos.2048, P.Nos.416 |
| 230 | Ground Floor |
| 231 | Providing soak pit of size 120cm x 120cm x 120cm including excavating and filling with brick-bats. . Spec. No. Bd.V.46, Page Number 576. SSR I.No.42.19, Sr.No.1390, P.No.275 |
| 232 | Ground Floor |
| 233 | RWH - Shallow Percolation Pit providing, constructing 2.0m deep shallow depth percolation pit comprising of 1.0m dia pre-cast RCC rings, 300mm thick side filling around outside of RCC rings (annular space) with 40mm size boulders including filling of percolation pit up to 0.5m depth (from bottom up) with 25-75mm clean washed gravels followed by 0.5m depth of 10-25mm of clean washed stones followed by 0.5m of washed river fine aggregate (natural sand/crushed sand VSI grade finely washed etc.) including netlon mesh between each gravel/fine aggregate (natural sand/crushed sand VSI grade finely washed etc.) media layer including covering with RCC slab, manhole frame & cover, PVC rungs etc. including arrangement for inlet & outlet pipe, excavation & backfilling as shown in the drawing. The rate shall be inclusive of all labour, material, wastage, scaffolding, transportation, taxes, including all leads, lifts at all levels. All material should be of approved make. All works complete as per the drawing, technical specification and direction of the Engineer in charge. Spec. No. Bd.V.46, Page Number 576. SSR I.No.48.46, Sr.No.1662, P.No.317 |
| 234 | Ground Floor |
| 235 | Providing and fixing board displaying information, such as 'Name of work, Tender cost, Name of Contractor, Work completion and liability period etc', having rectangular shape of 1.20m x 0.90m size made out 18 gauge (1.25mm) thick mild steel sheet painted with one coat of Zinc chromate stoving primer and two coats of enamel paint on front side and grey stove enamel on back side and border / messages / symbols etc. with approved colour shade paint complete, on M.S.angle of size 35 x 35 x 3 mm frame with properly cross braced M.S. angles of size 35mmx35mmx3mm duly painted including Two M.S. angle iron posts of size 65 mm x 65 mm x 6 mm, 3.65 m long painted with alternate black and white bands of 25 cm width including all fixtures etc.and fixing the boards in 1:4:8 concrete block of size 60 cm x 60 cm x 75 cm including, excavation, refilling, transportation, and labour etc complete. Spec. No. As directed by Engineer in Charge Spec. No. MORTH 801.SSR I.No.6.36, Sr.No.284 P.No.60 |
| 236 | Ground Floor |
| 237 | COMPOUND WALL |
| 238 | Excavation for foundation in earth, soil of all types, sand, gravel and soft murum, including removing the excavated material up to a distance of 50 m. beyond the building area and stacking and spreading as directed, dewatering, preparing the bed for the foundation and necessary back filling, ramming, watering including shoring and strutting etc. complete. (Lift upto 1.5 m.) By Mechanical Means Bd.A.1 Page Number 259. SSR I.No. 21.02, Sr.No.721, P.No.153 |
| 239 | Excavation for foundation in earth, soils of all types, sand,gravel and soft murum, including removing the excavated material upto a distance of 50 metres beyond the building area and stacking and spreading as directed, dewatering, preparing the bed for the foundation and necessary back filling, ramming, watering including shoring and strutting etc. complete. (Lift from 1.5m to 3.0m) By Mechanical Means Spec.No.: Bd.A.2 Page Number 259 SSR I.No.21.04, Sr.No.723 P.No.153 |
| 240 | Providing soling using 80 mm size trap metal in 15 cm. layer including filling voids with Crushed sand/grit, ramming, watering etc. complete. Spec. No. As directed by Engineer in charge. SSR I.No. 21.40, Sr.No. 754, P.No. 157 |
| 241 | Providing and laying Cast in situ/Ready Mix cement concrete in M15 of trap/ granite/ quartzite/ gneiss metal for bed blocks, foundation blocks and such other items including bailing out water, Steel centering, formwork, laying/ pumping, compacting, roughening them if special finish is to be provided, finishing uneven and honeycombed surface and curing etc. complete. The Cement Mortar 1:3 plaster is considered for rendering uneven and honeycombed surface only. Newly laid concrete shall be covered by gunny bag, plastic, tarpaulin etc. (Wooden centering will not be allowed.), with fully automatic micro processor based PLC with SCADA enabled reversible Drum Type mixer/ concrete Batch mix plant (Pan mixer) etc. complete. With fine aggregate (Crushed sand VSI Grade) Sepc. No. Bd.E.4 Page Number 289 and B7, Page Number38. SSR I.No. 24.08, Sr.No. 830, P.176 |
| 242 | Providing and laying Cast in situ/Ready Mix cement concrete M-15 of trap/ granite/quartzite/gneiss metal for coping to plinth or parapet, moulded or chamfered as per drawing or as directed including steel centering, plywood/ steel formwork compacting, roughening them if special finish is to be provided, finishing uneven and honeycombed surface and curing etc. complete. The Cement Mortar 1:3 plaster is considered for rendering uneven and honeycombed surface only. Newly laid concrete shall be covered by gunny bag, plastic, tarpaulin etc. (Wooden centering will not be allowed.) With fine aggregate (Crushed sand VSI Grade) Spec No. : Bd.E. 3/ Page No.288/ I.S. 456 (2000).SSR I.No.24.16, Sr.No.835, P.No.177 |
| 243 | Providing and laying in situ /Ready Mix cement concrete M-20 of trap / granite /quartzite/ gneiss metal for R.C.C. work in foundations like raft, strip foundations, grillage and footings of R.C.C. columns and steel stanchions etc. including bailing out water, Steel centering formwork, laying/pumping cover blocks, compaction and curing roughening the surface if special finish is to be provided (Excluding reinforcement and structural steel) etc. complete, with fully automatic micro processor based PLC with SCADA enabled reversible Drum Type mixer/ concrete Batch mix plant (Pan mixer) etc. complete. With fine aggregate (Crushed sand VSI Grade) Spec. No.Bd.F.3 Page No. 298 and B.7, Page No.38. SSR I.No.25.11, Sr.No.836 P.No.178 |
| 244 | Providing and laying Cast in situ/Ready Mix cement concrete M-20 of trap / granite /quartzite/ gneiss metal for R.C.C. columns as per detailed designs and drawing or as directed including steel centering, formwork, cover blocks, laying/pumping, compaction finishing the formed surfaces with cement mortar 1:3 of sufficient minimum thickness to give a smooth and even surface or roughening if special finish is to be provided and curing etc. complete.(Excluding reinforcement and structural steel).with fully automatic micro processor based PLC with SCADA enabled reversible Drum Type mixer/ concrete Batch mix plant (Pan mixer) etc. complete. With fine aggregate (Crushed sand VSI Grade) Spec. No. : Bd.F.5 Page No. 300 and B.7, Page.No. 38.SSR I.No.25.31, Sr.No.841, P.No.179 |
| 245 | Providing and laying Cast in situ/Ready Mix cement concrete M-20 of trap / granite /quartzite/ gneiss metal for R.C.C. beams and lintels as per detailed designs and drawings or as directed including steel centering, formwork, cover blocks, laying/pumping, compactionand roughening the surface if special finish is to be provided and curing etc. complete. (Excluding reinforcement and structural steel). with fully automatic micro processor based PLC with SCADA enabled reversible Drum Type mixer/ concrete Batch mix plant (Pan mixer) etc. complete. With fine aggregate (Crushed sand VSI Grade) Spec. No. Bd.F.6 Page No. 300 and B.7, Page No.38.SSR I.No.25.50, Sr.No.846, P.No.181 |
| 246 | Providing and fixing in position TMT - FE - 500 bar reinforcement of various diameters for R.C.C. pile caps, footings, foundations, slabs, beams columns, canopies, staircase, newels, chajjas, lintels pardis, copings, fins, arches etc. as per detailed designs, drawings and schedules. including cutting, bending, hooking the bars, binding with wires or tack welding and supporting as required complete. Spec.No. Bd.F.17, Page No. 306. SSR I.No.26.33, Sr.No.871, P.No.188 |
| 247 | Providing fly ash brick masonry with conventional/ I.S. type bricks in cement mortar 1:6 in superstructure including striking joints, raking out joints, watering and scaffolding etc. Complete. Spec. No. As director by engineer incharge and BDG- 2 and 5. SSR I.No.27.13, Sr.No.900 P.No.198 |
| 248 | Providing sand faced plaster externally in cement mortar using approved screened sand, in all positions including base coat of 15 mm thick in cement mortar 1:4 using waterproofing compound at 1Kilogramper cement bag curing the same for not less than 2 days and keeping the surface of the base coat rough to receive the sand faced treatment 6 to 8 mm thick in cement mortar 1:4 finishing the surface by taking out grains and curing for fourteen days scaffolding etc.complete. Spec. No. : Bd.L.7 Page No. 369. SSR I.No.32.11, Sr.No.963, P.No.209 |
| 249 | Providing groove to required size at specified location as directed by Engineer, at junction of brick masonry wall and R.C.C beams or Column, at junction of composite masonry, including scaffolding, finishing, curing etc. complete. Spec. No. As directed by Engineer in charge. SSR I.No.32.37, Sr.No.987, P.No.212 |
| 250 | Providing and applying three coats of water proof cement paint of approved manufacture and of approved colour to new plastered surfaces including scaffolding if necessary, cleaning and preparing the surface, watering for two days etc. complete. Spec.One Numbe Bd.O.8/Page OneNumber406. SSR I.No.35.15, Sr.No.1085, P.No.224 |
| 251 | Providing and fixing 50 mm. dia. medium class G.I.pipe gate with wicket gate of approved drawing with all fixtures and fittings in two leaves with strong hold fast embedded in c.c. block at top and bottom with locking arrangement including cutting, bending, making holes and with one coat of primer etc. complete. Spec. No. As directed by Engineer in charge. SSR I.No.23.05, Sr.No.820 P.No.173 |
| 252 | CC ROAD |
| 253 | Excavation for roadway in earth, soil of all sorts, sand, gravel or soft murum including dressing section to the required grade, camber and side slopes and conveying the excavated materials with all lifts upto a lead of 50m. and spreading for embankment or stacking as directed. Spec. No.MORTH 301 SSR I.No.2.11, Sr. No. 87 P.No.23 |
| 254 | Providing earth work in embankment with approved materials obtained from departmental land upto lead of 50m. including all lifts, laying in layers of 20cm. to 30cm. thickness breaking clods, dressing to the required lines, curves, grades & section, watering and compaction with vibratory roller to achieve not less than 97 % of standard proctor density etc. complete ( Material obtained from departmental Land) Spec. No. MORTH 401 SSR I.No.2.27, Sr. No.100 P.No.25 |
| 255 | Construction of granular sub-base by providing close graded Material, mixing in a mechanical mix plant at OMC, carriage of mixed Material to work site, spreading in uniform layers with motor grader/ Paver on prepared surface and compacting with vibratory roller to achieve the desired density, complete as per clause 401 -- Plant Mix Method and Grading - I Material. Spec. No. MORTH 401 SSR I.No.3.01, Sr. No.113 P.No.27 |
| 256 | Construction of dry lean cement concrete Sub- base over a prepared sub-grade with coarse and fine aggregate ( natural sand/ VSI grade finely washed crushed sand) conforming to IS: 383, the size of coarse aggregate not exceeding 25 mm, , cement content not to be less than 150 kg/ cum, optimum moisture content to be determined during trial length construction, concrete strength not to be less than 10 Mpa at 7 days, mixed in a batching plant/ Weigh batch mixer, transported to site with all leads and lifts, laid with a paver with electronic sensor /by suitable means as approved by Engineer-in-charge , compacting with vibratory roller, finishing, curing and including preparation of sub-grade surface if required etc. complete. SSR I.No. 5.13, Sr. No.181, P.No.43 |
| 257 | Providing and laying in situ cement concrete M -30 with tremix treatment for 200 mm thickness for Concrete Road is including laying plastic sheet for 125 micron thicknesswith groove cutting of 4 mm wide and 20 mm deep with necessary refilling with bitumen( excluding reinforcement) with coarse and fine aggregate ( natural sand/ VSI grade finelywashed crushed sand) etc. complete with fully automatic micro processor based PLC withSCADA enabled reversible Drum Type mixer/ concrete Batch mix plant (Pan mixer) etc. complete. SSR I.No.5.22, Sr. No. 190, P.No.44 |
| 258 | Providing and fixing in position TMT FE 500, tie bars precoated with anticorrosive epoxy paint of 12 mm dia. 70 cms.long and at 30.00 cm. C/C and wherever directed including handling, straightening wrapping with paper of approved quality for half length, necessary cutting, handling, straightening , supported by assembly of TMT FE 500, chairs with proper alignment etc. complete. Spec.no. MORTH 602.6.4.2 SSR I.No.5.16 Sr. No. 184, P.No.43 |
| 259 | Supplying hard murum/ kankar at the road site, including conveying and stacking complete. SSR I.No.2.29a, Sr.No. 102 P.No.25 |
| 260 | Spreading hard murum/ soft murrum/ gravel or kankar for side width complete. SSR I.No.2.30, Sr. No. 104 P.No.25 |
| 261 | Compacting the hard murum side widths including laying in layers on each side with vibratory roller including artificial watering etc. complete. SSR I.No.2.31, Sr. No. 105, P.No.25 |
| 262 | Conveying materials obtained from road cutting including all lifts, laying in layers of 20cm to 30cm. breaking clods, dressing to the required lines, curves, grades and section, watering and compacting to not less than 97% of standard Proctor density for a lead of over 50m. to 300m. inclusive from the site of excavation to the site of deposition as directed. SSR I.No.2.25, Sr.No.98 P.No.24 |
| 263 | B.T ROAD |
| 264 | Providing earth work in embankment with approved materials obtained from departmental land or other sources upto lead of 50m. including all lifts, laying in layers of 20cm. to 30cm. thickness breaking clods, dressing to the required lines, curves, grades and section, watering and compaction with Power roller to achieve not less than 97 % of standard proctor density etc. complete (with prior permission of SE) MORTH 305 SSR I.No.2.27 P.No.21 |
| 265 | Supplying hard murum/ kankar at the road site, including conveying and stacking complete.DSR I.No.2.29 P.No.22 |
| 266 | Spreading hard murum for side width etc. complete DSR I.No.2.30 P.No.22 |
| 267 | Compacting the hard murum side widths including laying in layers on each side with power roller including artificial water ing etc. complete. DSR I.No.2.31 P.No.22 |
| 268 | Construction of granular sub-base by providing close graded material, spreading in uniform layers with motor grader / Paver on prepared surface, mixing by mix in place method with rotavator at OMC, and compacting with vibratory roller to achieve the desired density, complete as per clause 401 -- By Mix in Place Method and Grading - I Material DSR I.No.3.04 P.No.23 |
| 269 | Providing, laying, spreading and compacting stone aggregates of specific sizes to water bound macadam specification including spreading in uniform thickness, hand packing to proper grade and camber, applying and brooming requisite type of screening/ binding Materials to fillup the interstices of coarse aggregate, watering and compacting with Intelligent Compactor with compaction analyzer and V-Sat at tachment . to the required density. Grading I (Using Screening Type A (13.2) mm Aggregate)DSR I.No.3.18 P.No.25 |
| 270 | Providing, laying, spreading and compacting stone aggregates of specific sizes to water bound macadam specification including spreading in uniform thickness, hand packing to proper grade and camber, applying and brooming requisite type of screening/ binding Materials to fillup the interstices of coarse aggregate, watering and compacting with Intelligent Compactor with compaction analyzer and V-Sat attachment. to the required density. Grading II (Using Screening Type B (11.2 mm) Aggregate) SSR I.No.3.20 P.No.25 |
| 271 | Providing and constructing 75 mm. thick Modified Penetration Macadam (MPM) road surface including all materials, preparing the existing road surface, spreading 40 mm. stone metal layers 30% crusher broken metal + 70% Hand broken (by breaking rubble obtained by blasting) heating and spraying the bitumen of VG-30 grade@2 Kg/ sqm, spreading 12 mm.size chips compacting with three wheel static roller having weight 8 to 10 MT. to achive the desired degree of compaction as per Technical Specification Clause 506 etc. complete. Including picking of existing WBM surface. Spec No. IRC-SP-20, 2002 Clause No. 8.7.3. DSR I.No.3.35 P.No.27 |
| 272 | Open Graded Premix Surfacing- Providing and Laying OGC 20 mm thickness composed of 13.2 mm to 5.6 mm aggregates premixed with bituminous binder transported to site with VTS, laid over a previously prepared surface, finished to the required grade, level, alignment , and rolling to achieve the desired compaction VG-30 Bitumen, including providing and laying seal coat sealing voids in a bituminious surface laid to the specified level and cross fall using Type A seal coat but excluding prime / tack coat . For Bitumen VG-30 bulk--USING drum mix type hot mix plant with SCADA, Paver and Vibratory roller MORTH 510 SSR I.No.4.08 P.No.33 |
| 273 | Providing and applying tack coat on the prepared surface heating by fames in Boiler and spraying bitumen with sprayer on Dry / Hungry B.T. surface 3 kg/10 sqm. (VG-30 bulk bitumen rates are considered to arrive at rates) SSR I.No.3.31 Sr.no.141 P.No.30 |
| 274 | Providing and laying of Type - B premix seal coat with HMP of approprate crushed stone chipping 6.70 mm size and penetration bitumen of specified grade @ 0.68Kilogram/ Square Metre. , preparing existing road surface including mixing in suitable Batch Mix plant and rolling by static roller having weight 8 to 10 MT. etc. complete. (VG-30 bulk bitumen rates are considered to arrive at rates) MORTH 513 SSR I.No.4.03 Sr.no.161 P.No.35 |
| 275 | DISMANTLING |
| 276 | Excavation for foundation in earth, soil of all types, sand, gravel and soft murum, including removing the excavated material up to a distance of 50 m. beyond the building area and stacking and spreading as directed, dewatering, preparing the bed for the foundation and necessary back filling, ramming, watering including shoring and strutting etc. complete. (Lift upto 1.5 m.) By Mechanical Means INo. Bd.A.1 Page No.259 SSR No.21.02 I.No.719, Page No.115 |
| 277 | Ground Floor |
| 278 | Conveying materials obtained from road cutting including all lifts, laying in layers of 20cm to 30cm. breaking clods, dressing to the required lines, curves, grades and section, watering and compacting to not less than 97% of standard Proctor density for a lead of over 50m. to 300m. inclusive from the site of excavation to the site of deposition as directed. Spec. No. MORTH 305 SSR I.No. 2.25, Sr.No. 98 P.No.24 |
| 279 | Ground Floor |
| 280 | Dismantling stone masonry in Mud including stacking the materials as directed with all leads, lifts etc. complete. SSR No.46.10 Sr. No.1548, Page No.296 |
| 281 | Ground Floor |
| 282 | Dismantling brick masonry in lime or cement mortar and stacking the materils as directed with all leads, lifts etc. S.S.R No.46.09 I.No.1547, Page No.296 |
| 283 | Ground Floor |
| 284 | Dismantling the R.C.C. Work 1:2:4 and sorting out the materials such as steel etc. as directed and stacking them within the specified lead as directed etc. complete. S.S.R No.46.29 I.No.1565, Page No.297 |
| 285 | Ground Floor |
| 286 | Removing brick bat coba including stacking the spoils as directed with all leads, lifts etc, complete.Spec.No.: Bd.A.2 Page 1 Number 259 SSR I.No.46.14, Sr.No.1552 P.No.296 |
| 287 | Ground Floor |
| 288 | Removing cement tiles, or marble or polished shahabad floor or dado without bed concrete including stacking the materials as directed with all leads, lifts etc. completeS.S.R No.46.19 I.No.1557, Page No.297 |
| 289 | Ground Floor |
| 290 | Removing doors and windows with frames and stacking the materials as directed with all leads, lifts etc. complete. As directed by Engineer incharge. S.S.R No.46.15 I.No.1539, Page No.215 |
| 291 | Ground Floor |
| 292 | Removing ventilators and small windows with frame and stacking the materials with alleads, lifts etc. complete... As directed by Engineer in charge. SSR I.No.46.16, Sr.No.1554 P.No.296 |
| 293 | Ground Floor |
| 294 | Removing urinal pans or wash hand basins with frame including disconnecting the sanitary and water supply connections, removing the same carefully and stacking the serviceable materials as and where directed including throwing the unserviceable materials outside etc complete INo. Bd.A.1 Page No.259 SSR No.46.40 I.No.1576, Page No.298 |
| 295 | Ground Floor |
| 296 | Removing W.C. pans including disconnecting the sanitary and water supply connections, removing and breaking flooring and bed con-crete around pan removing the same carefully and stacking the serviceable materials as adn where directed including throwing the unserviceable materiasls out side etc. carefully and throwing out the refusal outside etc. complete INo. Bd.A.1 Page No.259 SSR No.46.41 I.No.1577, Page No.298 |
| 297 | Ground Floor |
| 298 | SUMPWELL AND PUMPHOUSE |
| 299 | Excavation for foundation in earth, soil of all types, sand, gravel and soft murum, including removing the excavated material up to a distance of 50 m. beyond the building area and stacking and spreading as directed, dewatering, preparing the bed for the foundation and necessary back filling, ramming, watering including shoring and strutting etc. complete. (Lift upto 1.5 m.) By Mechanical MeansBd.A.1 Page Number 259. SSR I.No. 21.02, Sr.No.721, P.No.153 |
| 300 | Excavation for foundation in earth, soils of all types, sand,gravel and soft murum, including removing the excavated material upto a distance of 50 metres beyond the building area and stacking and spreading as directed, dewatering, preparing the bed for the foundation and necessary back filling, ramming, watering including shoring and strutting etc. complete. (Lift from 1.5m to 3.0m) By Mechanical Means Spec.No.: Bd.A.2 Page 1 Number 259 SSR I.No.21.04, Sr.No.723 P.No.153 |
| 301 | Conveying materials obtained from road cutting including all lifts, laying in layers of 20cm to 30cm. breaking clods, dressing to the required lines, curves, grades and section, to not less than 97% of standard Proctor density for a lead of over 50m. to 300m. inclusive from the site of excavation to the site of deposition as directed. Spec. No. MORTH 305 SSR I.No. 2.25, Sr.No. 94 P.No.24 |
| 302 | Filling in plinth and floors with contractors material/brought from outside and approved by Engineer incharge in layers of 15 cm to 20 cm including watering and compaction etc. complete. Spec. No. Bd.A.11 Page Number 263. SSR I.No. 21.37, Sr.No. 751, P.No. 157 |
| 303 | Providing soling using 80 mm size trap metal in 15 cm. layer including filling voids with Crushed sand/grit, ramming, watering etc. complete. Spec. No. As directed by Engineer in charge. SSR I.No. 21.40, Sr.No. 754, P.No. 157 |
| 304 | Providing and laying Cast in situ/Ready Mix cement concrete in M-10 of trap/ granite/ quartzite/ gneiss metal for foundation and bedding including bailing out water, Steel centering, formwork, laying/pumping, compacting, roughening them if special finish is to be provided, finishing if required and curing complete, with fully automatic micro processor based PLC with SCADA enabled reversible Drum Type mixer/concrete Batch mix plant (Pan mixer) etc. complete. With fine aggregate (Crushed sand VSI Grade) Spec. No. Bd.E.1 Page No. 287.SSR I.No.24.01, Sr.No.827, P.No.175 |
| 305 | Providing and laying in situ /Ready Mix cement concrete M-20 of trap / granite /quartzite/ gneiss metal for R.C.C. work in foundations like raft, strip foundations, grillage and footings of R.C.C. columns and steel stanchions etc. including bailing out water, Steel centering formwork, laying/pumping cover blocks, compaction and curing roughening the surface if special finish is to be provided (Excluding reinforcement and structural steel) etc. complete, with fully automatic micro processor based PLC with SCADA enabled reversible Drum Type mixer/ concrete Batch mix plant (Pan mixer) etc. complete. With fine aggregate (Crushed sand VSI Grade) Spec. No.Bd.F.3 Page No. 298 and B.7, Page No.38. SSR I.No.25.11, Sr.No.836 P.No.178 |
| 306 | Providing and laying Cast in situ/Ready Mix cement concrete M-20 of trap / granite /quartzite/ gneiss metal for R.C.C. columns as per detailed designs and drawing or as directed including steel centering, formwork, cover blocks, laying/pumping, compaction finishing the formed surfaces with cement mortar 1:3 of sufficient minimum thickness to give a smooth and even surface or roughening if special finish is to be provided and curing etc. complete.(Excluding reinforcement and structural steel).with fully automatic micro processor based PLC with SCADA enabled reversible Drum Type mixer/ concrete Batch mix plant (Pan mixer) etc. complete. With fine aggregate (Crushed sand VSI Grade) Spec. No. : Bd.F.5 Page No. 300 and B.7, Page.No. 38.SSR I.No.25.31, Sr.No.841, P.No.179 |
| 307 | Providing and laying Cast in situ/Ready Mix cement concrete M-20 of trap / granite /quartzite/ gneiss metal for R.C.C. beams and lintels as per detailed designs and drawings or as directed including steel centering, formwork, cover blocks, laying/pumping, compactionand roughening the surface if special finish is to be provided and curing etc. complete. (Excluding reinforcement and structural steel). with fully automatic micro processor based PLC with SCADA enabled reversible Drum Type mixer/ concrete Batch mix plant (Pan mixer) etc. complete. With fine aggregate (Crushed sand VSI Grade) Spec. No. Bd.F.6 Page No. 300 and B.7, Page No.38.SSR I.No.25.50, Sr.No.846, P.No.181 |
| 308 | Providing and laying Cast in situ/Ready Mix cement concrete M-20 of trap/ granite / quartzite/ gneiss metal for R.C.C. slabs and landings as per detailed designs and drawings including steel centering, formwork, cover blocks, laying/pumping, compaction finishing the formed surfaces with cement mortar 1:3 of sufficient minimum thickness to give a smooth and even surface or roughening if special finish is to be provided and curing etc. complete,(Excluding reinforcement and structural steel).with fully automatic micro processor based PLC with SCADA enabled reversible Drum Type mixer/ concrete Batch mix plant (Pan mixer) etc. complete. With fine aggregate (Crushed sand VSI Grade) Spec No.Bd.F.8 Page No. 302 and B.7, Page No.38. SSR I.No.25.70, Sr.No.851 P.No.182 |
| 309 | Providing and laying Cast in situ/Ready Mixcement concrete M-20 of trap/ granite/ quartzite/ gneiss metal for R.C.C. chajja as per detailed design and drawings including steel centering, formwork, cover blocks, laying/pumping, compacting and roughening the surface if special finish is to be provided and curing complete. (Excluding reinforcement and structural steel). with fully automatic micro processor based PLC with SCADA enabled reversible Drum Type mixer/ concrete Batch mix plant (Pan mixer) etc. complete. With fine aggregate (Crushed sand VSI Grade) Spec.No. Bd.F.9 Page No. 303 and B.7, Page No.38.SSR I.No.26.05, Sr.No.856, P.No.184 |
| 310 | Providing and laying Cast in situ/Ready Mix cement concrete in M-20 of trap/ granite/ quartzite/ gneiss metal for R.C.C. pardi of required thickness including steel centering, formwork, cover blocks, laying/pumping, compacting , curing , finishing and rougheningthem if special finish is to be provided and curing complete.(Excluding reinforcement and structural steel).with fully automatic micro processor based PLC with SCADA enabled reversible Drum Type mixer/ concrete Batch mix plant (Pan mixer) etc. complete. With fine aggregate (Crushed sand VSI Grade) Spec. No. Bd.F.11 Page No. 304 and B.7, Page No. 38.SSR I.No.26.17, Sr.No.860, P.No.185 |
| 311 | Providing and fixing in position TMT - FE - 500 bar reinforcement of various diameters for R.C.C. pile caps, footings, foundations, slabs, beams columns, canopies, staircase, newels, chajjas, lintels pardis, copings, fins, arches etc. as per detailed designs, drawings and schedules. including cutting, bending, hooking the bars, binding with wires or tack welding and supporting as required complete. Spec.No. Bd.F.17, Page No. 306. SSR I.No.26.33, Sr.No.871, P.No.188 |
| 312 | Providing fly ash brick masonry with conventional / I.S. type fly ash bricks in C.M. 1:6 in foundation and plinth including bailing out water manually striking joints, racking out joints watering and scaffolding etc. complete..Spec. No. As director by engineer in charge and BDG- 2 and 5. SSR I.No.27.12, Sr.No.899 P.No.198 |
| 313 | Providing and fixing 20 to 25 mm thick rough shahabad box type waterproofing for basement or underGround Floor on a base of Cement concrete 1:3:6, including sub base of 2.50 centimeter thick Cement mortar 1:3 with conceal, secrete (RMW), Algae proof or other alike waterproofing liquids, raking of joints upto 35 mm depth, filling the joints with 6 mm size crushed metal, hand grouting with cement slurry, curing and cleaning, with 7 years guarantee on court fee stamp of Rs. 100/- with ponding test etc complete. (excluding Cement concrete 1:3:6 base concrete ) Spec. No. : Bd.J.2 Page Number 355. SSR I.No.31.12, Sr.No.948, P.No.206 |
| 314 | Providing and fixing 20 to 25 mm thick rough shahabad box type waterproofing treatment to vertical outside faces of Reinforced Cement concrete walls of basement or underGround Floor including filling the gap of 25 mm between rough shahabad and R.C.C. walls with cement grout mixed with water proofing liquid Algae proof or other alike with one tile lift method, brushing the joints horizontally with cement slurry mixed with water proofing liquid for width 30 to 35 mm and sloping coping over topmost tile with cement mortar 1:3, butting the bottom most with Cement concrete 1:2:4 mixed with water proofing liquid, curing, with 7 years guarantee on court fee stamp of Rs.100/- with ponding test etc complete. (excluding Cement concrete 1:3:6 base concrete) Spec. No. : Bd.J.2 Page Number 355. SSR I.No.31.13, Sr.No.949, P.No.207 |
| 315 | Providing internal cement plaster 12mm thick in single coat in cement mortar 1:5 without neeru finish to concrete or brick surfaces, in all positions including scaffolding and curing etc. Spec. No. : Bd.L.4 Page No. 368. SSR I.No.32.03, Sr.No.957, P.No.209 |
| 316 | Providing internal cement plaster 20mm thick in Single coats in cement mortar 1:5 without neeru finish, to concrete, brick surface, in all positions including scaffolding and curing etc. complete Spec. No. : Bd.L.4 Page No. 368. SSR I.No.32.06, Sr.No.960, P.No.209 |
| 317 | Providing sand faced plaster externally in cement mortar using approved screened sand, in all positions including base coat of 15 mm thick in cement mortar 1:4 using waterproofing compound at 1Kilogramper cement bag curing the same for not less than 2 days and keeping the surface of the base coat rough to receive the sand faced treatment 6 to 8 mm thick in cement mortar 1:4 finishing the surface by taking out grains and curing for fourteen days scaffolding etc.complete. Spec. No. : Bd.L.7 Page No. 369. SSR I.No.32.11, Sr.No.963, P.No.209 |
| 318 | Providing neeru finish to plastered surfaces in all positions including scaffolding and curing etc. complete.Spec. No. : Bd. L.10, Page No.370. SSR I.No.32.15, Sr.No.966, P.No.210 |
| 319 | Providing fine cement finish 1.5 mm thick over green plaster surface including scaffolding curing etc. complete. Spec. No. : As directed by Engineer in charge. SSR I.No.32.21, Sr.No.972, P.No.210 |
| 320 | Providing and applying Two coats of wall care Putty on plastered surface and Ceiling and Walls to prepare surface even and smooth of approved make, etc complete.. Spec No.: As directed by Engineer in charge. SSR I.No.32.34, Sr.No.985, P.No.212 |
| 321 | Providing and laying vitrified mirror / glossy finish tiles decorative type having size 590 mm to 605 mm x 590 mm to 605 mm of 8 to 10 mm thickness and confirming to IS. 15622-2006 ( group Bla) of approved make, shade and pattern for flooring in required position laid on a bed of 1:4 cement mortar including neat cement float, filling joints, curing and clearing etc. complete. Spec. No. Bd.M.12 Page No. 385. SSR I.No.33.40, Sr.No.1027 P.No.217 |
| 322 | Providing and laying vitrified mirror / glossy finish tiles having size 590 mm to 605 mm x 590 mm to 605 mm of 8 to 10 mm thickness and confirming to IS. 15622-2006 ( group Bla) of approved make, shade and pattern for dado and skirting in required position fixed in 1:4 cement mortar including neat cement float, filling joints, curing and clearing etc. complete Spec. No. Bd.M.12 Page 1 No. 385. SSR I.No.33.41, Sr.No.1028 P.No.217 |
| 323 | Providing and applying three coats of water proof cement paint of approved manufacture and of approved colour to new plastered surfaces including scaffolding if necessary, cleaning and preparing the surface, watering for two days etc. complete.Spec.One Number:Bd.O.8/Page One Number406 SSR I.No.35.16, Sr.no.1086 P.No.224 |
| 324 | Providing and fixing rolling shutter fabricated from steel laths of minimum thickness 0.9 mm with lock plate of 3.15 mm thickness reinforced with 35 x 35 x 5 mm angle section fitted with sliding bolts and handles for both sides, deep M.S. channel section of depth and thickness not less than 65 mm and 3.15 mm respectively with hold fast arrangements, M.S. Bracket plate 300 x 300 x 3.15 mm minimum size and shape with square bar, suspension shaft of minimum 32 mm diameter, hood cover of M.S. sheet not less than 0.9 mm thickness and of any size at top and safety devices including mechanical gear operation arrangement consisting of worm gear wheels and worms of high grade cast iron or mild steel and one coat of red lead primer etc. complete. (I.S. 62481979) (With mechanical gear) Spec.No.BD-T-55 Page Number 510 SSR I.No.39.25, Sr.No.1218 P.No.249 |
| 325 | Providing and fixing in position (as per 1868 / 1982) Aluminium sliding window of three tracks with rectangular pipe 95 x 38.10 x 0.90 mm at weight 0.637 Kilogram/One Running Metre. with window frame bottom track section 92 x 31.75 x 1.30 mm at weight 1.070 Kilogram/One Running Metre.. Top and side track section 92 x 31.75 x 1.30 mm at weight 0.933 Kilogram/Running metre. The shutter should be of bearing bottom 40 x 18 x 1.25 mm at weight 0.417 Kilogram/One Running Metre. Inter locking section 40 x 18 x 1.10 mm at weight 0.469 Kilogram/Running metre. and handle and top section 40 x 18 x 1.25 mm at weight 0.417 Kilogram/Running metre. As per detailed drawings and as directed by Engineerincharge with all necessary Aluminium sections fixtures and fastenings such as roller bearing in nylon casting and self locking catch fitted in vertical section of shutter including 5 mm thick plain glass and aluminium mosquito net shutter with stainless steel jail with all required screws and nuts etc, complete. With powder coating without box Spec. No. : As directed by Engineer in charge. SSR I.No.39.44, Sr.No.1237 P.No.254 |
| 326 | Providing and laying telephone black / Amba White / Cadburybrown / Ruby red / Ocean Brown granite stone of 18 to 20 mm thick for door frame/ dado/ window boxing etc. On C.M. 1:6 including filling joints with polymer base filler nosing/moulding the sharp edges wherever necessary, curing, etc. complete.Spec. No. As directed by Engineer-In- Charge. SSR I.No.33.68, Sr.No.1052 P.No.220 |
| 327 | Providing and fixing mild steel grill work for windows, ventilators, etc. 15 Kilogram/ One Square Metre as per drawing including fixtures necessary welding and painting with one coat of anticorrosive paint and two coats of oil painting complete. Spec. No. : Bd.U. 1 Page No. 537. SSR I.No.40.02, Sr.No.1292 P.No.264 |
| 328 | Providing and Fixing mat finish stainless steel (of 302 grade ) railing with top pipe of 50 mm dia. and vertical pipe of 38 mm dia at 0.60 m c/c or as required and horizontal pipes of 25 mm dia in three rows, all pipes of 2 mm thick including buffing,fabricating fixtures and fastening including pipe base of appropriate diameter and ball base of 75 mm dia above newel post of 75 mm diameter etc. complete (Prior approval of sample and brand by Ex.Engineer is necessary before use Spec No.:As directed by Engineer Incharge.SSR I.No.40.08, Sr.No.1298 P.No.265 |
| 329 | Boring work (including transport.) 200/215 mm diameter in the soil / gravel surface Bore diameter of 150 mm in solid rock. This includes diameter drilling work. (Wet drilling) MJP Bore Well SSR Shedule 'B' A (item no 1)विंधण काम (वाहतुकीसह.) माती / मुरुमाच्या भूप्रस्तरात २०० / २१५ मी.मी. व्यासाचे विंधणकाम व पक्क्या पाषाणात १५० मी.मी. व्यासाच्या विंधण कामाचा यात समावेश आहे. (वेट ड्रिलिंग) |
| 330 | After completion of drilling bore well, capacity test by flushing (air lift method) is measured with 90 degree \\"V\\" notch. MJP Bore Well SSR Shedule 'B' A (item no 2)विंधण विहीर पूर्ण केल्या नंतर फ्लूशिंगद्व्यारे (air lift method) क्षमता चाचणी ९० अंशाच्या \\"व्ही\\" नॉचने मोजणे |
| 331 | 180 mm diameter PVC Casing pipe (8 kg / cm2) (IS 4985-1988)In exceptional circumstances / Casing pipes with a rock surface and if more than 40 feet of casing pipe is required, the casing should be used with the technical approval of the Deputy Engineer and Geologist.१८० मी.मी. व्यासाचा पी.व्ही.सी. केसिंग पाईप (८ कि.ग्रॅ. / से.मी.) (IS ४९८५-१९८८)अपवादात्मक परिस्थितीमध्ये/दगड गोट्यांचा भूस्तर असलेल्या ठिकाणी व ४० फुटापेक्षा केसिंग पाईप अत्यावश्यक असल्यास उपअभियंता व भुवैज्ञानिक यांच्या तांत्रिक मान्यतेने सदर केसिंग वापरण्यात यावा. |
| 332 | 180 mm diameter PVC Casing pipe (8 kg / cm2) (IS 4985-1988) Casing lowering, grounding१८० मी.मी. व्यासाचा पी.व्ही.सी. केसिंग पाईप (८ कि.ग्रॅ. / से.मी.) (IS ४९८५-१९८८)केसिंग लोअरिंग, ग्राऊंटिंग करणे. |
| 333 | 180 mm diameter cap for PVC pipe.१८० मी.मी. व्यासाचा पी.व्ही.सी. पाईप साठी कॅप. Please Enable Macros to View BoQ information |
AI Tender Summary
Tender Timeline
Jul 08, 2026
11:30 IST
Tender Published
Tender notice published.
CompletedJul 16, 2026
17:00 IST
Bid Submission Deadline
Online submission via eProcurement portal.
Upcoming · 6 daysJul 17, 2026
Bid Opening Date
Technical bids will be opened and evaluated.
Upcoming · 7 daysTender Documents
Download All (ZIP) ↓
Disclaimer
We takes all possible care for accurate & authentic tender information. However users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender