Tender For Dry Docking & Allied Repairs Of Of installation Nireekshak (Sr 26)
Tender Value
Ref. Documents
Estimated cost
Bid Submission
29 Jul 2026
12 days left
EMD
2 Crore
Bank guarantee accepted
Document Fee
Ref. Documents
Non-refundable
Tender Type
Online
Tender Overview
Organization
Tender ID
Competition Type
NCB
Bidding Type
Tender
Location / State
Ernakulam → Kerala
EMD Exemption
Available
Quantity
Not Available
Website
Contact Person
Address
Project Description
Tender for Dry Docking & Allied Repairs Of Of installation Nireekshak (Sr 26)
BOQ
| Sl. No. | Item Description |
| 1 | SUMMARY OF QUOTATION |
| 2 | ServicesTotal Cost of Dry Dock Hire Charges and other Admin & General Services quoted in the BoQ |
| 3 | Cost of repair part :-(a) Total cost of Hull Work Package |
| 4 | (b) Total cost odf Engineering Work Package |
| 5 | (c) Total cost of Electrical Work Package |
| 6 | (d) Total cost of Diving Work Package |
| 7 | GST on serial 1.01 to 1.05 |
| 8 | Total Budgeary Cost of Spares |
| 9 | GST applicable for 1.07 |
| 10 | Any other Taxes & Duties |
| 11 | Miscellaneous (not included in any of the serial above) |
| 12 | GST if any on serial 1.10 |
| 13 | HULL - PART I |
| 14 | SR 4 - During SRs/NRs, tanks, cofferdams and sea tubes which are repaired by build-up/renewal are to be air pressure tested iaw para 47 of NO 01/15. The pressure testing is to be carried out by Refitting Authorities in the presence of ship staff and Quality Control inspectors of the Refitting Authority. Under no circumstance, the procedure of running pressure test is to be used to confirm the structural integrity of these spaces. |
| 15 | SR 1 - SS to chip, clean all tanks, tank tops, bilges of machinery spaces, cofferdams, shaft recess and other accessible internal surface of underwater hull up to and including area 500mm above boot top line. Project specific defect to DYD defects to DYD for survey/repairs. Dockyard to carry out repair of the same. |
| 16 | SR 2 - Dockyard to carry out visual survey of area at SR2 and repair as per NO 01/15. SS to restore the paint scheme. |
| 17 | SR 3 - Dockyard to carry out survey and inspection of all bollard/fairlead/cleat/ deck eyes/ staghorn and other deck fittings structure including stiffening members in the vicinity with non-destructive techniques. |
| 18 | SR 1 - All tanks, cofferdams and sea tubes which are repaired by build-up/renewal or are subjected to hot work for welding of pad piece/ foundation on any of their boundaries are to be air pressure tested. The pressure applied should never exceed that which corresponds to a pressure of 0.2 kg/sq cm (2 meters of water or 0.20 bars or 2.1/2 ibf/ sq in).Note: All outstanding defects affecting water tight integrity of W/T compartments/ clusters/ tanks, which could not be rectified during previous operational cycle, are to be projected in Defect List Part II. |
| 19 | SR 3 - Carry out 100% visual survey of external UW hull structure in accordance with NO 01/15. (a) 100% visual survey of external UW hull and USG Survey in way of machinery compartment.( Group- D ships ) |
| 20 | SR 4 - Excessive areas of breakdown of abrasive anticorrosive paints to be blasted and recoated with full paint scheme. Paint scheme on full underwater hull and boot top including wind and water areas i.e. area up to 500mm above boot top area is to be restored. Surface preparation to be undertaken iaw with NO 53/16. Paint scheme repair/ repairs is to be undertaken iaw IHQ, MoD (N) policy letter NC/0528/LLPS dated 20 Jul 11 and NCD 1491 issue 1 of May 11. |
| 21 | SR 6 - Paint scheme of all technical windows above water line to be restored iaw NO 53/16. Test and trials of all renewed plates are to be carried out iaw para 42 and 43 of NO 01/15. |
| 22 | SR 1 - Remove marine fouling from the hull using wooden scrapper or hydro jetting with maximum pressure not exceeding 3000 psi. |
| 23 | SR 2 - Scrape and clean under water and boot topping area (including wind and water areas) to remove all loose paint film, rust etc. Wind and water areas to be considered up to 500mm above boot top. |
| 24 | SR 5 - Application of one coat of antifouling paint on underwater hull and boot top area to be carried out post adequate surface preparation based on the finndings of joint inspection with OEM. Paint touchup and maintenance painting to be carried out i.a.w NO 53/16. |
| 25 | SR 3 - Check clearances of lower and upper beaings or bushes, whichever is fitted, of rudder. Renew/ repack rudder bearings/ gland bushes, if required. SS to record in EMAP. |
| 26 | SR 4 - Examine rudder pintle bearings to ensure that they are fully lubricated before undocking. |
| 27 | SR 2 - Examine underwater structure in accordance with NO 01/15, paying particular attention to hull plating in the vicinity of rudder(s), fitting upto the rudder head, for signs of corrosion, defects and damage. |
| 28 | SR 1 - Carry out abrasive blasting/ scraping to bare metal of areas of corrosion/ paint damage. Restore the paint scheme as per ship's UW paint schemein accordance with NO 53/16. |
| 29 | SR 2 - Clean remaining sacrificial anodes with steel wire brush.NOTE:- Ensure sacrificial anodes are not painted. Any paint or coating over the anodes is to be scrapped clean before undocking. |
| 30 | SR 1 - Inspect sacrificial anodes fitted to underwater hull, rudders, rope gaurd, shaft tunnel, stern tubes, inlets and outlets, sea tubes, bilges and coffer dams. Renew those consumed 50% or more. |
| 31 | SR 2 - Paint inlets and discharges in accordance with NO 53/16 and policy issued by IHQ/DNA from time to time. |
| 32 | SR 1 - Remove, clean and examine gratings of minimum 25% under water inlets and discharges. Examine plating, coating and zincs of inlets and discharges and areas adjacent to them. Replace grating on completion of any repair and recoat work on inlets, discharges and gratings. Sea tubes graded critical during the proceeding refit to be examined & repaired. |
| 33 | SR 3 - Visual survey of 25% of sea tubes (as indicated by SS) post removal of valves. Endoscopic survey of remaining 75% of sea tubes may be carried out. |
| 34 | SR 1 - Remove, clean and examine gratings of all under water inlets and discharges. Examine plating, coating and zincs of inlets and discharges and areas adjacent to them. Replace gratings post completion of repair and recoat work on inlets, discharges and gratings. [Note:- Valves are required to be opened by SS/Yard (>100mm). SS to chip, clean and prepare the surface area and offer for survey. SS to blank the sea tubes in case of requirement. Assistance of yard may be sought towards provision of blanks. |
| 35 | SR 2 - Carry out 100% visual survey and endoscopy of all sea chest/ sea tubes/ UW inlets/ outlets and OBDs for internal corrosion, pitting and cracks etc. Sea tubes graded critical during the preceding refits are to be ultrasonically surveyed and repaired as per instruction contained in the Navy Order 01/15. Undertake air pressure test of all repaired/ renewed sea tubes/sea chest and OBDs post structural repair/ renewal. (For all ships)Note: (i) All seatubes are to be surveyed irrespective of their material. During survey of sea tubes, specific attention is to be paid to the neck region. All branch pipes/ flush through lines welded to sea chest/ seatubes are to be surveyed as part of seatubes. In case of Talwarclass of ships, the rubber lining of the sea tube shall be inspected for any deterioration and water entrapment.(ii) Conditional assessment of bimetallic joints is to be carried out whilst undertaking survey of the seatubes. 100% endoscopy of seatubes is to be carried out post repairs and application of coating prior to undocking of the ship.(iii) Sea tubes not accessible for survey and painting because of small diameter are to be renewed. |
| 36 | SR 3 - All Sea chest/sea tubes and OBDs which are repaired by build-up/renewal are to be air pressure tested iaw Para 47 of NO 01/15. The pressure testing is to be carried out by Refitting Authorities in the presence of ship staff and Quality Control inspectors of the Refitting Authority. Under no circumstance, the procedure of running pressure test is to be used to confirm the structural integrity of these spaces. |
| 37 | SR 4 - Restore/renew paint scheme of all UW sea chest/ sea tubes/ OBDs with appropriate paint scheme post completion of survey and repair as per NO 53/16 and policy directives issued by IHQ/DNA time to time. Sea tubes removed for repair to be abrasive blasted and coated with paint scheme prior to fitment. Plates laps, welds etc to be faired with epoxy putty before application of paint. For FAC class, ships seatubes are to be painted with separate paint scheme as approved by IHQ/DNA. |
| 38 | SR 1 - Survey all under water appendages/ fittings for pitting, corrosion or any damage paying particular attention to paint failure/ damage area to stern shaft bracket, ropeguard, eddy plates, eddy cones, stern tube, skeg, bilge keel plate, stabilizers fin etc. iaw NO 01/15. Undertake repair as necessary |
| 39 | SR 2 - Clean to bare metal all corroded area and area of paint failure of U/W appendages and preserved in accordance with NO 53/16 and policy directives issued by NHQ/IHQ time to time. |
| 40 | SR 3 - Check draught marks are in position and intact with ship structure. (NES-164/DEFSTAN 02-164 & BR 3001 Chapter 28 article 2811). Undertake painting of draft marks as per NO 53/16 and policy directives issued by IHQ/DNA from time to time. |
| 41 | SR 4 - Examine fairing of underwater appendages for roughness and unfairness or any damage paying particular attention to the shaft brackets, ropeguards and eddy plates etc. Renew/repair the unfaired/damaged fairing for their smoothness. |
| 42 | SR 5 - Clean and repaint the sea side surface of stabilizer fin boxes. The fin wings extended and turned to maximum angle to the horizontal to give better access to the fin box (if applicable) |
| 43 | SR 6 - Check clearance for stabilizer fins (if applicable). |
| 44 | SR 7 - Recoat shaft brackets in accordance with NO 53/16 |
| 45 | SR 9 - Carry out 100% NDT of the weld joints of bilge keel or pressure testing of bilge keel |
| 46 | SR 1 - Examine mast structure, whip aerial platforms and the surrounding structure on deck, eye plates, load carrying members for signs of corrosion. Examine bolted, riveted and intermittent welded structure connections for signs of fracture. Portable and semi portable fittings to be removed for closer examination of structure underneath. Any known defects to be raised to dockyard for rectification. |
| 47 | SR 3 - Survey and test all standing & running riggings fitted on mast structure along with associated fittings. Renew wire ropes and associated fittings as necessary. |
| 48 | SR 4 - Carry out load testing of eye plates, bottle screws etc if due (not to exceed 27 months). |
| 49 | SR 2 - Sample visual survey of dadoe of bulkeads in wet compartments and rectify defects observed |
| 50 | SR 1 - Examine funnel casing both internal and external, paying particular attention to plating and perforated sheet, wire mesh etc, casing on internal side (if applicable). Portable or semi portable fittings that obscure structure are to be removed for the examination of structure behind. Project the specific defects to yard for liquidation. Structure revealed post removal of semi portable fittings to be preserved in accordance as per NCD and NO 53/16 and policy letters. |
| 51 | SR 1 - Calibrate the over-load mechanism of starter |
| 52 | SR 2 - Check contact and wiring for wear/deterioration. renew as necessary. |
| 53 | SR 3 - Examine entire assembly including brake lining ,brake shoe, brake disc and associated fittings. renew brake lining and shoe of excessively worn down |
| 54 | SR 4 - Survey all wire ropes, spare gear and other associated lifting gears. renew as necessary. |
| 55 | SR 5 - Carry out SPM checks on electrical motor. Lubricate/replace bearing as necessary. |
| 56 | SR 8 - Inspect the worm wheel assembly for any wear and presence of metallic particles. |
| 57 | SR 7 - Open slewing assembly bearing housing and inspect bearing for play. Renew if necessary |
| 58 | SR 6 - Overhaul electric motor subject to QC check.Carry out trials on completion of repairs. |
| 59 | SR 9 - Check oil in gear case and examine gear teeth for breakage and presence of foreign matter.Check bearings for collapse and shaft for rust and corrosion.Renew/repair as necessary. |
| 60 | SR 10 - Record Volt/Amps/Speed parameters of davit and associated systems during load test.Record load test details. |
| 61 | SR 11 - Check brake lining on winch and change liner if damaged. |
| 62 | SR 12 - Check all rotating parts, lever etc for free movement. |
| 63 | SR 1 - Check oil leakage from pump. Renew seals , gaskets. Renew worn out parts. |
| 64 | SR 3 - Check pressure relief valve for correct setting. |
| 65 | SR 7 - Check the air gap between the brake pad and brake disc. Adjust as required. |
| 66 | SR 9 - Overhaul the following:-(a) Mooring cooling water pump(b) Oil circulating pump |
| 67 | SR 6 - Remove the brake pads , wash the discs with trichloroethylene. |
| 68 | SR 7 - Carry out electrical checks such as IR and HV on starter panels/armature windings. If neccesary apply varnish by brush and allow to dry. |
| 69 | SR 2 - Carry out slew ring wear test by measuring instruments with an exactness of atleast 1/10 mm. The safe funtioning of the slew ring is dangerously reduced if the maximum allowable deviation is exeeded. |
| 70 | SR 6 - Change the filter element of the built in filters. A clogged filter element causes a \\"BY-PASS\\" through the filter which results in the system operating with un-filtered oil. |
| 71 | SR 8 - Check serviceability of bearing. If necessary overhaul the motor. |
| 72 | SR 1 - Check the bolts by tightening them with the specified torque. During the operation the bolted connection must be relieved of all tensile stresses coming from external loads. |
| 73 | SR 3 - Hydraulic oil in the hydraulic system is to be laboratory tested. The lab report will help in determining the life span of the oil. |
| 74 | SR 4 - Keep the system clean. Change filter elements regularly. Change hydraulic fluid when recommended by lab or once every year. |
| 75 | SR 9 - Load test the crane and associated fittings as per NCD 3910. Period test should not exceed 27 months. |
| 76 | SR 5 - Slew/winch/travel gear box (with oil immersed multi-plate brake). Make: Homworthy. Change oil every 200 running hours or once every year as per specified grade:- AGIP BLASIA 150 |
| 77 | SR 1 - Surface preparation by hydro blasting of the anchors, chain cable and associated accessories is to be carried out prior to undertaking visual survey |
| 78 | SR 4 - Carry out survey of all stopper assemblies by removing the joining shackle and open up the pelican hook. Hammer test all parts of the stopper assembly, including each chain cable link and the pelican hook. Visually examine all parts of the stopper assembly for crack and distortion. Check pelican hook, buckler link for operation and ease of movement and ability to secure the pelican hook. If the buckler link is difficult to operate, It must be made workable by cleaning and greasing the pin. Examine for corrosion, particularly in stress areas. iaw NO 02/21. |
| 79 | SR 5 - Unscrew bottle slip/ compressor whereas fitted to its fullest extent and thoroughly clean and grease threads before assembly. |
| 80 | SR 6 - Undertake survey of adapter piece for cracks or wear and undertake repair as per NO 02/21 |
| 81 | SR 7 - Survey all deck fittings associated with anchor chain cable arrangement ie deck eyes/ eye plates including gulletine/ gulletine roller, compressor with complete structure whereas fitted paying particular attention eye plates/ eye bolts etc for wear, corrosion/ deterioration and ovality of hole. Undertake repair/ renewal iaw NO 02/21. |
| 82 | SR 9 - Survey anchor, chain cable, swivel adaptor, shackles and all associated fittings (An experienced Dockyard blacksmith is to assist the survey). Break, clean and grease all joining shackles. Undertake repair/renewal as applicable iaw 02/21. Forward a report on IN 305/nso 269(b) to authorities as mentioned in para 15 of NO 02/21. |
| 83 | SR 1 - Survey and renew suspect safety nets if not carried out during last 3 years. SS to maintain record of survey and renewals. |
| 84 | SR 6 - Renew air filter elements / pads/ frames. |
| 85 | SR 5 - Blow through of trunking with compressed air / Automatic robotic cleaning be undertaken to Ventilation trunkings observed clogged / dirty as indicated by SS. |
| 86 | SR 7 - Remove, chemically clean (both air and water side), pressure test and fit back twelve ATU coolers associated with Volna system (HF & TS). Restore trunkings and lagging on completion. |
| 87 | SR 8 - Remove, overhaul and refit all the pneumatic mushroom heads associated with Volna compartments. Test for correct operation on completion of job. |
| 88 | SR 3 - Where the grease filters consist of a single sheet of copper in the gauge frame which slides into a housing in the exhaust trunkings (some ships may have gauge boxes fitted in the canopies) the portable section of the lining between the filter and the equipment served is to be removed and the internal surfaces of portable, canopy and trunking thoroughly cleaned. Carryout random checks to confirm necessity of internal surface cleaning. |
| 89 | SR 2 - Renew motor and blower/impeller bearings fitted subject to QC checks (SS to forward SPM readings to DYD). |
| 90 | SR 1 - Examine the interior of hot water and fresh water expansion tanks for corrosion. Raise specific defects to dockyard as necessary. |
| 91 | SR 4 - Strip and clean 50 % of soil and urinal drain pipes. Re-galvanize where required. |
| 92 | SR 3 - Strip, clean and overhauling of 50 % WC and urinal flushing valves, reducing valves and reducer. |
| 93 | SR 1 - Strip, examine and refit 50% of discharge valves (All valves are to be examined during a three year period). |
| 94 | SR 2 - Strip, examine and refit 50% of geared storm valves. Renew wornout leather seatings, where necessary (All valves are to be examined during a three year period). |
| 95 | SR 3 - Strip, examine and refit 50% of non-geared storm valves. Renew wornout leather seatings where necessary (All valves are to be examined during a three year period). |
| 96 | SR 4 - Strip, examine and refit 50% of plug cock valves (All valves are to be examined during a three year period). |
| 97 | SR 2 - Examine the structure of all Fuel/Lub oil tanks including tanktops for pitting, corrosion and other structural defects and damage. Project specific defects to yard for rectification. Exterior surfaces of tanks surveyed during periodical survey of structure to be included in defect list together with a list of items / fittings and machinery which will be required to be lifted to facilitate survey. |
| 98 | SR 4 - Undertake pressure testing of Fuel/ Lub oil tanks which are repaired by build-up/ renewal iaw Para 47 of NO 01/15. The pressure testing is to be carried out by Refitting Authorities in the presence of ship staff and Quality Control inspectors of the Refitting Authority. Under no circumstance, the procedure of running pressure test is to be used to confirm the structural integrity of these spaces. |
| 99 | SR 3 - Examine preservative coating of tanks. Project specific defects related to yard. Yard to restore paint scheme iaw NCD 1491, NO 53/16 and policy directive issued by IHQ/DNA as applicable.Note:(a) Inspection of Paint OEM be carried out wherever applicable(b) Galvanised ladders are not to be painted. Ensure that suction strainer boxes are clear.(c) The surface preparation work and painting interiors of fresh water and distilled water tanks is required to be undertaken by healthy personnel, wearing clean outfits. On completion, of painting, each tank should be inspected to ensure that the coating/ paint film completely covers the surface, with particular attention to parts of the structures which are not readily visible.(d) The minimum time for filling the fresh water tank if freshly coated should be 7 days. The tanks should be washed out with fresh water and any sediment or dirt present should be removed and the covers are closed before the tanks are brought into use.(e) The water sample from the tank after 72 hours of immersion should be sent to NMRL or the Naval Dockyard laboratories for potability test prior to use of water for drinking purpose. |
| 100 | SR 8 - Undertake pressure testing of FW tanks which are repaired by build-up/ renewal iaw Para 47 of NO 01/15. The pressure testing is to be carried out by Refitting Authorities in the presence of ship staff and Quality Control inspectors of the Refitting Authority. Under no circumstance, the procedure of running pressure test is to be used to confirm the structural integrity of these spaces. |
| 101 | SR 8 - Undertake air pressure testing of all ballast tanks which are repaired by build-up/renewal iaw Para 47 of NO 01/15. Note: - The pressure testing is to be carried out by Refitting Authorities in the presence of ship staff and QC inspectors of the Refitting Authority. Under no circumstance, the procedure of running pressure test is to be used to confirm the structural integrity of these spaces. |
| 102 | SR 9 - Undertake visual survey of all tanks and check the paint condition of all ballast/ trimming tanks including fittings inside the tanks for any paint defects/ deterioration. Restore/ renew, whichever is applicable, the paint scheme of affected areas post appropriate surface preparation. |
| 103 | SR 4 - Examine the condition of sacrificial anode fitted in cofferdam and void spaces, if any. Undertake renewal of sacrificial anodes if consumed beyond 50%. |
| 104 | SR 5 - Restore paint scheme of cofferdams and void spaces in accordance with relevant NO 53/16/ NCD 1491/ policy directives and post survey and renewal. |
| 105 | SR 6 - Undertake pressure testing of all cofferdams and void spaces which are repaired by build-up/ renewal iaw Para 47 of NO 01/15. The pressure testing is to be carried out by Refitting Authorities in the presence of ship staff and Quality Control inspectors of the Refitting Authority. Under no circumstance, the procedure of running pressure test is to be used to confirm the structural integrity of these spaces. |
| 106 | SR 3 - Undertake air pressure testing of all sludge and bilge tanks which are repaired by build-up/renewal iaw Para 47 of NO 01/15. Note: - The pressure testing is to be carried out by Refitting Authorities in the presence of ship staff and QC inspectors of the Refitting Authority. Under no circumstance, the procedure of running pressure test is to be used to confirm the structural integrity of these spaces. |
| 107 | SR 2 - Carry out leak test of fuel tank by LP air with assistance from repair yards.Note: (For Afloat Units every refits) |
| 108 | SR 1 - Weigh the RIB and compare with ideal weight. Record the same in Boat log book. Undue increase of weight, if any be reported for detailed examination.(Note: - For afloat units during every refits.) |
| 109 | SR 2 - FSWR slings to be load tested iaw INBR 1552. Period of test should not exceed 27 months. (Note :- For Afloat Units every refits.) |
| 110 | SR 1 - Brows are to be examined, repaired as necessary. Dockyard testing not more than 16 months.NOTE: Brows are to be tested at the first opportunity after any repairs carried out by ships staff. |
| 111 | SR 2 - Provide necessary input on weight of items removed/ replaced to the Ship Staff during refit with the following details: - (a) Weight of equipment/ components including installation material being added/ removed and items being degutted/ re-gutted. In case of non- availability of details of weight, actual weighing of items is to be ensured. (b) Co-ordinates (X, Y, Z) of centre of gravity of all weight are to be provided for recording in the Weight Management Book. |
| 112 | SR 3 - Scrutinise the weight calculation forwarded by SS and provide assistance in finalising the positions of additional weights (if reqd) for docking/undocking. |
| 113 | SR 1 - Weight Control Team is to be constituted to record and monitor the weight of items taken in and out of the ship. Weight changes are to be recorded in the Weight Management Book. |
| 114 | SR 2 - Provide necessary input on weight of items removed/ replaced to the Ship Staff during refit with the following details: - (a) Weight of equipment/ components including installation material being added/ removed and items being degutted/ re-gutted. In case of non- availability of details of weight, actual weighing of items is to be ensured. (b) Co-ordinates (X, Y, Z) of centre of gravity of all weight are to be provided for recording in the Weight Management Book. |
| 115 | SR 3 - Scrutinise the weight calculation forwarded by SS and provide assistance in finalising the positions of additional weights (if reqd) for docking/undocking. |
| 116 | SR 1 - Weight Control Team is to be constituted to record and monitor the weight of items taken in and out of the ship. Weight changes are to be recorded in the Weight Management Book. |
| 117 | HULL - PART II |
| 118 | Metallic scuppers along with rubber scupper lips at scattered location on weather deck corroded and perished .To be renewed.Qty-15 |
| 119 | Outlet discharge of various drainage lines on ship side corroded and perished .To be renewed.Qty-12 |
| 120 | Renewal of silicon rubber beading of escape hatch to be undertaken. Job involve removal of old rubber beading and fitment of new silicon rubber beading. Post renewal of silicon rubber beading, chalk test of same to be undertaken. |
| 121 | Portable holding stanchions along with stanchion shoe at winch deck corroded thinned and holed to be undertaken. Job involves degutting and regutting of lagging and panelling. |
| 122 | Manufacturing of portable hand rails near emergency escape scuttle at officer`s lobby to be undertaken. |
| 123 | Teak wood at quarter deck damaged and perished. Same to be renewed in situ. Wood to be provided by yard. |
| 124 | Wooden sealant between teak wood at quarter deck to be restored. |
| 125 | Manufacturing of cover for drain line at quarter deck to be undertaken as per dimension. Mat- MS. Approx length- 10 Meter. |
| 126 | Deck eye for securing of oxygen quads on quarter deck corroded thinned and holed. Same to be renewed in situ. Work involves removal of teak wood and deck underlay. Post renewal of deck eyes restoration of deck underlay of surrounding area, DPT and load testing for the deck eyes to be undertaken. Qty-30, SWL-1 Ton. |
| 127 | Survey and load testing of deck eyes at various locations on upper deck to be undertaken. If found unsat, same to be renewed as per existing dimensions. |
| 128 | Overhead rope reel in ASP along with its foundation, bracket and operating mechanism corroded thinned and holed. To be renewed as per existing dimension in situ. Work involves manufacturing of new rope reel and fitment the same. |
| 129 | 06 number rope reels on weather deck not freely rotating to be repaired/ renewed. Job involves- Dismantle the rope drum.Qty-06, Renew the bushes of rope drum.qty-04 in each drum. Material-brass .Size dia-80mm, Repair or Renewed metallic parts if found damaged, Refit the rope drum and brake assembly and prove the operation of rope drum.Qty-06. |
| 130 | Platina ropes for securing of tyre fender along with Stainless steel D-shackles and wire mousing damaged/perished to be renewed as per existing dimensions in situ |
| 131 | Kick-out panel along with frames of NWT doors damaged and perished. To be renewed as per dimension. |
| 132 | Perspex sheet doors of cabinet damaged and perished in Electrical, CPO cabin and diving cabin to be renewed as per dimension. |
| 133 | 20 in nos NWT doors of accommodation containers and cabins along with Door frames, rubber beading , Kick out panel, Mortise Locks and stoppers corroded thinned and damaged to be renewed as per existing dimensions and specifications. 02 in no. Acoustic & Fire retardant doors with vision panel of dimension ( 300 x300) mm to be fitted in MCR (Port and Stbd) alongwith frame. All items to be provided by yard. |
| 134 | Hydraulic door closer of various NWT doors are to be renewed at various places.Qty-20. Items to be provided by yard. |
| 135 | Wooden beading of dado area in alleyways is damaged/ broken to be renewed as per existing wooden beading. Mat-wood |
| 136 | All 23 in nos tanks to be ventilated by using exhaust and supply blowers for a duration of 48 hours. Once all tanks are cleaned Gas free, men entry and safe for hot work certificate to be obtained by shipyard from authorised agency. Qty-23 tanks Job involves opening of manholes and ventilation for all 23 tanks. |
| 137 | Post obtaining men entry certificate, All 23 tanks to be manually cleaned and left over fuel or fresh water or feed water or sludge to be removed thereafter. Cater for removal approx 300 KG of sludge from each tank. |
| 138 | Examine condition of paint coating (OM 750) on tanks, system pipelines passing through tanks, fitting and structure. Clean to bare metal wherever corrosion is evident or paint coating is damaged, affected due to hot work, paint as per approved paint scheme (OM 750) to be applied. Paints to be provided by yard.APT of all tanks those who are subject to hot work is to be undertaken prior commencement of painting. |
| 139 | All 7 in nos tanks to be ventilated by using exhaust and supply blower for a duration of 48 hours. Once tanks are cleaned gas free, man entry and safe for hot work certificated to be obtained by shipyard from authorised agency. shipyard to obtain man entry clearance certificate from authorised agency for all 07 fresh water tanks. Job involves opening of manholes for all 7 tanks. |
| 140 | Post obtaining men entry certificate, all 7 in nos tanks to be manually cleaned and left over fresh water or sludge to be removed thereafter. Cater for removal of approx 01 ton of sludge from each tank. |
| 141 | Full paint scheme to be restored in affected due to hot work or mechanical damage restore iaw 53-16. APT of tanks those who will be subjected to hot work to be undertaken prior commencement of painting. Paints to be provided by yard. |
| 142 | Post inspection of fresh water tanks if more than 50 percent of EP-1 coating has deteriorated, dockyard to preserve the all 7 tanks completely iaw no 53-16. Paints to be provided by yard. |
| 143 | All tanks to be ventilated by using exhaust and supply blower for a duration of 48 hours .Once tanks are cleaned, gas free and man entry safe for hot work certificates to be obtained by shipyard from authorised agency. Job involves opening of manholes for all 10 tanks. |
| 144 | Post obtaining men entry certificate, all tanks to be manually cleaned and left over sea water or sludge to be removed thereafter. Cater for removal for approx 01 ton of sludge from each tank. Qty-10 |
| 145 | Full paint scheme to be restore in affected area due to hot work mechanical damage restore iaw no 53-16. Apt of tanks those who will be subjected to hot work to be undertaken prior commencement of painting. No. Of ballast tanks -10. Paints to be provided by yard. |
| 146 | Repair plating structure and fitting of tanks as found necessary during inspection and survey. Renew stud of manhole covers and coaming. |
| 147 | Welding of bonding straps to be undertaken at indicated locations. Bonding strap to be provided by yard. |
| 148 | Bilge plates to be secured with the foundation by Dzus fasteners at various internal compartments Material SS. Qty -200 Nos. |
| 149 | Anticipated renewal of DMR 249A steel of various thickness of plate is 10 tons, thickness 04 mm to 16 mm. |
| 150 | HDNS Paint defect - blistering, peel off, crack observed at quarter deck, foxle and both catwalk to be renewed with existing paint scheme. Job involves surface preparation of ST-2.5 standard with hand tools and paint scheme to be restored iaw no 53-16. Area 1400 SQM. Paints to be provided by yard. |
| 151 | Undertake surface preparation and touch up painting of external above water ship side including moon pool area, super structure and all containers subjected to hot work/build up and plate renewal. |
| 152 | Undertake surface preparation and painti touch up of internal compartments as per existing paint scheme. Internal compartments included ASP, Aft Thruster, Shaft tunnel, SDC area, Engine room, STP, Fwd Thruster and Bosun store compartment. Paints to be provided by yard. |
| 153 | Carry out painting of draft marking, pennant number and Nireekshak font as per no 53-16. |
| 154 | Undertake surface preparation and painting of all water line marking, NBCD and volumetric marking including digit writing as existing in all underwater internal compartments. |
| 155 | Epoxy deck covering (deck underlay) of JS and SS bathroom cracked - uprooted. To be renewed. Job involves removal of old deck covering, prepare surface area for survey, after surface preparation survey the area and apply deck underlay. |
| 156 | Top coat of epoxy deck covering of all wet compartment cracked - uprooted. To be renewed. Job involves removal of old top coat and apply new top coat. Wet compartment includes SR & JR sailor bathroom, Galley, Laundry, Sick bay, Wardroom pantry & CO Pantry, JOM bathroom, ATU-1, ATU-2 compartment and all officers’ bathrooms. |
| 157 | Top coat of epoxy deck covering (Dark blue with sparkle) of all dry compartment cracked - uprooted. To be renewed. Job involves removal of old top coat and apply new top coat with sparkle. dry compartment includes CO Lobby, officer lobby, Dining hall and wardroom lobby, DCHQ lobby and Canteen lobby. |
| 158 | Dadoes casting at in all wet compartment to be undertaken. Height of dado casting should be 230mm. Job involves removal old dado casting up to bare metal and reapplying deck covering |
| 159 | Excessive noise and vibrations observed on laundry washing machine. Carry out DI/DR of laundry washing machine including drainage lines and valves. Repair-renew of defective part if any. Job involves complete dismantling of machine, maintenance and testing of all valves, check of bearing of rotating parts for any damage. If damage, renew the same. |
| 160 | Overhead CRCA and bulkhead panelling deteriorated at scattered location incuding MCR. To be renewed. Item to be provided by refitting authority. |
| 161 | SS panelling damaged at scattered locations in galley. To be renewed in situ. |
| 162 | Lub oil (OMD-113) to be charged post cleaning of gear box of both davits. 60 Ltr each. |
| 163 | 04 nos lub oil drain plugs of davit gear box damaged resulting in oil leakage .to be renewed. Leakage from gear box to be rectified. |
| 164 | Visual survey and load test of both safety preventer to be undertaken as per INBR 1552. If found unserviceable, same to be renewed. |
| 165 | Anchor winch observed slipped in clutched in position. DI/DR to be undertaken in presence of SS. |
| 166 | Excessive Noise, Vibration and jerk observed on all two mooring winch while Operation. Suspect loose securing clamps of hydraulic pipes in local control panel and weak foundation. DI-DR to be carried out. |
| 167 | Supporting brackets of. Mooring pipeline corroded or broken, to be renewed as per existing dimensions. |
| 168 | Mooring pipe line flanges and securing Allen bolts corroded and deformed, To be renewed. Replace various O-Rings of all joints. Each flange contains 04 number Allen bolts. |
| 169 | Leakage observed from hydraulic line local control panel, Port and Stbd at boat deck. To be repaired and renewed in situ.Qty-02. |
| 170 | Various hydraulic flexible hoses of hydraulic winch found defective to be renewed in situ as per existing dimensions. |
| 171 | Leakage observed from hydraulic motor and valves near hydraulic tank in engine room. To be repaired and renewed in situ.Qty-04. |
| 172 | Calibration of both tensiometer to be undertaken. If found defective during calibration, Renew/ repair of the same. |
| 173 | Static break motor along with bearing of both hydraulic winches defective. Same to be renewed. |
| 174 | \\"O\\" ring of all valves and joints of hydraulic line to be renewed with high pressure \\"o\\" rings. Working prressure-200 bar.Qty-100. |
| 175 | Calibration of all pressure gauges to be undertaken and calibration certificate to be provided to ship. Calibration date and next calibration due date to be pasted under each pressure gauge. Renewal of pressure gauges to be undertaken, if found defective. |
| 176 | Calibration and serviceability checks of all control panel along with all light indication in bridge and winch deck to be check. If found renewed the same. |
| 177 | Load test of both hydraulic anchor winch to be undertaken. Qty-02, static brake- 10 Ton, Disc brake- 04 Ton |
| 178 | Hydraulic pipe lines along with securing brackets of mooring winch corrored thined and holed to be renewed as per existing dimention. |
| 179 | Dismantle anchors, swivel pieces and D-shackle with pin from anchor steel wire rope. Qty- 02 for each anchor and wire rope. |
| 180 | Guide bracket along with full mechanism of tenso meter corroded and thinned to be repaired /renewed. |
| 181 | Carry out load test of anchor strop, dia meter 12 mm EFSWR.Qty-02. Static load- 3.4 Ton, breaking load-8.5 Ton. |
| 182 | oil leakage observed from hydraulic pump of both hydraulic door to be repaired. Hydraulic oil to be refilled. Renew parts those which found defective |
| 183 | Rubber beading of both hydraulic doors found damaged and perished. Same to be renewed as per existing specification. Post renewal of rubber beading, chalk test to be proven in presence of HITU and SS. |
| 184 | Undertake air hose test of common bulkhead of engine room -shaft tunnel and same to be witnessed by HITU (Koc). Job involves chalk testing of 02 hydraulic doors, renewal of rubber beading with hardness of 70‑90 A. |
| 185 | APT of 03 clusters to be undertaken and witnessed by HITU (Koc). If any defect observed during conducting of APT, the same defects to be rectify. |
| 186 | Carry out chemical cleaning of all pipe lines. Job involves dismantling of pipelines and refitment of pipe lines along with new gasket post cleaning. Post refitment of sewage pipes line, vacuum and leak test to be undertaken for finding any leakage. |
| 187 | Undertake effluent test of STP sewage and certificate for the same may be issued .Qty- 01. |
| 188 | Abnormal noise observed from both EVAC pumps. DI/DR of both pump along with motor and overhauling to be undertaken. Defective parts to be renewed, if found defective. |
| 189 | leakage observed from valves fitted in sanitary lines overhauling to be undertaken. |
| 190 | Functional checks and repairing of WC commode along with discharge valve, control mechanism, water valve, push button to be undertaken. Renew the same if found defective. QTY- 15 each |
| 191 | 10 in no WC commode back sitting cover broken. To be renewed as per sample. |
| 192 | Abnormal noise observed from CHT pump. E&R of CHT pump to be undertaken. if found defective, same to be renewed. |
| 193 | Renewal of mechanical seal of CHT pump to be undertaken. |
| 194 | Supporting bracket of pipe lines of CHT pumping out system corroded and thinned. To be renewed in situ. |
| 195 | System pipelines of CHT pumping out system corroded thinned and holed. Same to be renewed as per existing dimension. |
| 196 | Level gauge indicator of CHT malfunctioning / not working. Same to be repaired/renewed and proved in situ. |
| 197 | Clean the hydraulic oil tank and charge hydraulic oil if required (SS-32). |
| 198 | Boom of crane observed play in slew direction on rough sea. DI/DR to be undertaken. |
| 199 | Various hydraulic hoses of hydraulic deck crane found defective to be renewed in situ as per existing dimensions |
| 200 | Calibration of all pressure gauges to be undertaken and calibration certificate to be provided to ship. Calibration date and next calibration due date to be pasted under each pressure gauge. Renewal of pressure gauges to be undertaken, if found defective. |
| 201 | Calibration and functional checks of all control panels along with all light indications in crane to be check for operation. If found defective, renew the same. |
| 202 | Remove steel wire rope from crane and undertaken visual survey of wire rope and fitment back. |
| 203 | Carry out calibration of zinc reference electrode and multimeter. Calibration certificate for the same may be issued Qty- Each-01 |
| 204 | ATU filters of both ATUs corroded thinned and holed. To be renewed as per existing specification and dimensions |
| 205 | Grease filter housing and exhaust trunking of galley to be cleaned and refitted |
| 206 | Diffusers/Ventilation duct of AC trunking fitted in air conditioned compartments/cabins along with associated fittings damaged. To be renewed as per existing specification and dimension. Size of diffuser- 400 x 400 mm |
| 207 | Ventilation trunking meshes at various compartment and bathroom and WCs heavily corroded and holed to be renewed. Material-SS mesh . Qty-16. Job involves dismantle ventilation trunking, removal of cold lagging, degutting and regutting of panelling. Wire, lagging etc, securing of trunking with clamps. Qty-150 Rmtr. |
| 208 | Renew 05 number rubber beading on ventilation flaps as per existing specification. |
| 209 | 03 numbers mushroom heads corroded thinned and holed to be renewed as per existing specification. Material -MS. Cater for renewal of mushrooms along with deck penetrations. Material-MS. |
| 210 | 14in numbers mushroom head wire mesh broken, corroded to be renewed in situ. |
| 211 | 08 in numbers canvas bellow connecting between fan and trunking perished to be stitched as per sample |
| 212 | 05 in numbers spindle of mushroom head wheel jammed, to be eased and lubricated and leather seat to be renewed |
| 213 | Robotic cleaning of ventilation trunking in machinery compartment and accomodation spaces to be undertaken |
| 214 | Sacrificial anodes of all ballast tanks consumed. Shipyard to procure sacrificial anodes and same to be renewed in situ. Sacrificial anode- MK-II |
| 215 | Chilled water lagging of ventilation trunking and ATU drains to be renewed repaired as per existing specification. |
| 216 | Rubber beading of WT doors to be replaced with silicon rubber beading. Shipyard to provide silicon rubber beading. Job involves removal of old rubber beading and fitment of silicon rubber beading. Post fitment of silicon rubber coaming chalk test of all doors to be undertaken in presence of HITU and SS. |
| 217 | Rubber beading of WT hatches to be replaced with silicon rubber beading. Shipyard to provide silicon rubber beading. Job involves removal of old rubber beading and fitment of silicon rubber beading. Post fitment of silicon rubber coaming chalk test of all doors to be undertaken in presence of HITU and SS. |
| 218 | Locking mechanism along with handle jammed. DIDR of locking mechanism to be undertaken in situ. Renew defective parts if found defective. Post repaires chalk test to be undertaken in presence of HITU. |
| 219 | Back plates of WT hatches corroded thinned to be repaired in situ. |
| 220 | Strip and chemically clean all drain pipe including bathroom pipes renew where found defective. Regalvanised, repaint where required. |
| 221 | Drain pipe of split ACs to be chemically cleaned. Job involves removal of all deck drain and fitment of the same pipe lines post chemical cleaning. Renew the pipelines if necessary. |
| 222 | Strip, examine, overhaul and refit all ball valves. Renew all defective worn out parts. Qty -04 nos. |
| 223 | Water leakage observed from buoyancy chamber. DI/DR to be undertaken. Post defect rectification leak test to be carry out. Qty -02. |
| 224 | Collar of both RIBs observed damaged and faded. To be renewed with new collar. Type- foam filled collars. Qty -02. |
| 225 | Various fitting of 4.7 mtr ribs found loose/damaged to be renewed/repaired. |
| 226 | Hot water lagging in various bathrooms to be renewed in situ. |
| 227 | Chilled water lagging of split ac lines to be renewed repaired as per existing specification. |
| 228 | MWMB lagging damaged or perished at various locations. To be renewed in situ. |
| 229 | Insulation of HMP RU lockers perished-damaged. To be repaired renewed. Mat -phenolic foam. Qty- 04 |
| 230 | Locking mechanism of HMG RU locker along with handle damaged broken to be repaired. |
| 231 | Examine and repair or renew damaged or corroded MS stanchions along with stanchions shoe. |
| 232 | Carry out random load testing of PVC guardrails with end fittings and submit certificates to SS. |
| 233 | Metallic guardrails chains corroded and broken at various places on upper deck to be renewed. material SS . |
| 234 | Locking mechanism of cold and cool room defective. To be renewed. Qty-02 |
| 235 | Rubber beading of cool and cold room perished. To be renewed. Qty- 15 RMT |
| 236 | Door panelling cracked and broken to be renewed as existing. |
| 237 | Water condensation tray in cool and cold room damaged or broken to be renewed as per existing dimension. Mat-SS |
| 238 | Rubber beading of moon pool hatch perished and deteriorated. To be renewed as per sample. Post renewal chalk test to be carried out. Work involves removal of old rubber coaming, cleaning of ms coaming, application of primer on the coaming before fitment and refitment of new rubber. Shipyard to procure rubber beading to be procured from navy approved vendor viz- irmra, Mumbai. Note- size of moon pool and rubber beading- 40 mm x 25 mm, length 12000 mm. Qty-01 |
| 239 | Leakage observed from fresh water isolating valves in SS and JS bathroom. To be renewed. Qty-20 |
| 240 | GI pipelines in various bathrooms holed thinned and corroded. To be renewed in situ. Mat-.5 and 1 inch GI pipe .Qty-40 Rmtr. Job involves removal covering of hot lagging, degutting and regutting of panelling, cables, lagging associated fittings. |
| 241 | Wash basin of scullery and bathrooms corroded thinned and holed to be renewed and fitted as per existing specification and dimension. Mat-SS |
| 242 | 18 in no bottle traps of wash basin defective to be renewed. Work involves renewal of bottle trap and also caters modification of pipe required as per new bottle trap. |
| 243 | Wire braded hose of wash basin perished and worn out .to be renewed or replaced. Work involves removal of old wire braded hose and replacement with new wire braded hose and connecting hoses to wash basin taps. Hoses should sustain pressure of 05 Bar |
| 244 | 18 in no taps of water mixing taps of wash basin defective or water not holding to be renewed with superior quality jaguar push taps for wash basin. Job involves renewal of valves along with flexible wire braded hoses connection connecting to fixed piping of.5 inch |
| 245 | 15 in nos fixed shower arrangement along with shower head defective. To be renewed with superior quality fittings. Shipyard to procure fixed shower arrangement of jaguar make and cater for modification of securing bracket as per fixed shower arrangement. Job involves renewal of 15 in nos shower mixer along with supporting bracket. |
| 246 | Renewal of 'fixed shower piping with 0.5 inch steel coated pipe of length of 01 Mtr with end fittings for every shower mixer |
| 247 | 04 no of SS mirrors in bathroom perished or film damaged to be renewed . |
| 248 | 20 in no health faucets in various WCs defective or water not holding, to be renewed with superior quality faucets .work involves removal of old faucets and replacement of new faucets. Hoses should sustain pressure of 05 Bar. Qty-20. |
| 249 | 25 in nos tumbler bolts of the scuttles defective, bent, threading worn out. To be renewed. Mat-brass or ss.size-80mm long and 15 mm dia. |
| 250 | Rubber beading of port holes scuttles worn out. To be renewed and chalk tested. Post renewal of rubber beading, silicon gel to be applied arround the of rubber beading to avoide ingress of water.Qty-30 |
| 251 | Outside area around the scuttles are corroded and not accessible for maintenance. Area to be painted post surface preparation as per existing paint scheme. |
| 252 | Undertake fabrication type ladders in DCHQ lobby and officer lobby corroded, thinned and holed. To be repaired renewed. Ladder length-3 Mtr, width-200mm, steps-13, Mat- MS. Qty-03. |
| 253 | Aluminium straps of various footsteps of ladder damaged or broken to be renewed. Job involves removal of old straps and fitment of new straps. Mat-AL, Qty -50 mtr |
| 254 | Portable extendable aluminium ladder damaged and broken to be renewed as per existing dimension. |
| 255 | Carry out electroplating for the following - ships bell, ceremonial dice stanchions, ceremonial dice stanchions chains, ships builder tally, 02 in nos ships bell .Qty-8 Sqmtr |
| 256 | Manufacturing of new chart table in bridge to be undertaken as per existing specification and dimension. Mat-wood |
| 257 | 05 in nos lockers in bridge corroded thinned and holed to be renewed in bridge to be renewed as per existing dimension. Job involves removal of old damaged locker and fitment of new locker. |
| 258 | 02 in nos file rack in bridge, 03 file rack in hull office and 08 rack in paint store corroded thinned and holed to be renewed as per existing dimension. Job involves removal of old rack and fitment of new rack. |
| 259 | Water leakage observed from deck head through piercing of search light and magnetic compass. DI/DR to be undertaken in situ. |
| 260 | Drain pipe from bridge wing to stbd and port boat deck corroded thinned and holed to be renewed as per existing dimension. Dia- 2 inch |
| 261 | Cover of captain chair and seat cover of boat to be renewed as per existing specification. |
| 262 | Lifebuoy stand broken to be repair or renewed as per existing dimension. Mat-wood |
| 263 | Painting of ship's crest on Perspex sheet for lifebuoy stand to be undertaken. |
| 264 | Manufacturing of 02 in nos aluminium footstep for gangway to be undertaken as per dimension. |
| 265 | Awning cover of various equipment and fittings to be manufactured as per existing dimension. Equipment are 02 in nos 4.7 mtr RIB. |
| 266 | 04 in nos gangway state board broken or damaged to be repaired to be repaired. |
| 267 | Manufacturing of 02 in nos stand for gangway state board as per dimension and repair of 03 in nos stand for gangway state board to be undertaken. Mat-wood |
| 268 | Life raft cradle along with foundation corroded, holed to be repaired along with dropping system. Material-MS angle bar 30mm x 30 mm x4 mm and ms flat bar 300 x 4mm thick.qty-7,length-50 Rmtr. |
| 269 | Post inspection, Heave compensation assembly to be made operational considering all load conditions and to be proved during load test |
| 270 | Manufacturing of new pattern Ashoka emblem for lifebuoy stand, ship’s crest to be undertaken as per sample. Qty-Each-02 |
| 271 | Renewal and fitment of 04 in nos MOB marker along with securing arrangement to be undertaken. |
| 272 | 05 in nos lockers on weather deck corroded thinned and holed to be renewed as per existing dimension. Job involves removal of old damaged locker and fitment of new locker. |
| 273 | Locking arrangement of 03 in nos locker on deck no 1 to be repaired. |
| 274 | Manufacturing of portable sentry post for security sentry to be undertaken as per existing specification and dimension. |
| 275 | 02 in nos 51 mm mortar launcher stand damaged broken to be repaired |
| 276 | Office table along with its slider drawers with locking arrangement defective. To be renewed/repaired. |
| 277 | 03 in nos racks in ship's office corroded thinned and holed to be renewed. |
| 278 | Position of potato peeler machine along with foundation in ship's galley to be repositioned. |
| 279 | Vegetable cutting table with drawer corroded or damaged or broken. To be renewed as per existing specification. |
| 280 | Food tasting table below man trap alarm indicator damaged or broken. To be renewed. |
| 281 | Sliding mechanism in drawer in galley corroded thinned and holed to be renewed as per existing dimension. Mat-SS |
| 282 | Vertical lockers along with locking mechanism thinned corroded and hoed to be repaired /renewed in ERA mess. |
| 283 | Securing bracket of port ladder in E/R damaged broken to be welded. |
| 284 | RU locker with locking arrangement in E/R broken to be repaired. |
| 285 | Additional/Unnecessary fitting in E/R to be cut at various location |
| 286 | Shoe racks along with securing arrangement found defective to be renewed/repaired at various compartment. |
| 287 | Tables sliding drawers along with locking arrangement at various offices not functioning properly to be renewed or repaired |
| 288 | Locking mechanism along with keys found defective to be renewed at various containers to be undertaken. |
| 289 | Sliding mechanism of drawers along with locking arrangement below bunks are found damaged defective to be repaired/renewed at various compartment. |
| 290 | Locking arrangement along with of vertical lockers in various messes found defective to be repaired/renewed. |
| 291 | Renewal of 10 in nos jammed or perished hinged of EDA door to be undertaken. |
| 292 | Locking arrangement of 02 in nos SPTA lockers of EDA perished to be repaired/ renewed. |
| 293 | Doors of EDA corroded thinned and holed to be renewed as per existing dimension. |
| 294 | Securing frame of main broadcast speaker corroded thinned and holed to be repaired. |
| 295 | Manufacturing of seat cover for 04 in nos ready use storage boxes of MCR/SRE. |
| 296 | Flag locker broken damaged, to be repaired on bridge top as per sample, Mat - GI sheet |
| 297 | Securing strips of all PCs at wt office to be made. Mat-SS |
| 298 | Securing arrangement of operator chair at WT office to be undertaken. |
| 299 | Manufacturing of emblem for jack and ensign staff to be undertaken. |
| 300 | Manufacturing of Motorola charging bay at WT office to be undertaken as per sample. |
| 301 | File racks with securing strips at wt office perished. To be renewed/repaired as per existing dimension. |
| 302 | Aft thruster’s compartment bilge area is not accessible for survey and maintenance. Area to be surveyed and restore paint scheme post surface preparation up to SA 2.5. |
| 303 | Survey and renew if required of plate under taut wire bottle in port side engine room. |
| 304 | Survey of bilge frame to be undertaken in E/R, if found defective repair work be undertaken |
| 305 | 4 nos split AC foundation angles corroded thinned holed to be renewed in situ. Qty - 04. |
| 306 | 20 nos ship side MS eye of tyre fender corroded and thinned to be renewed Qty - 20. |
| 307 | Deck undulation observed at stbd catwalk near foxle, barber lobby, scullery area. Hull office, CPO cabin lobby, Survey of same area to be undertaken. Renewal/repair as found necessary. Job involves removal of old plates and renewal of new plates. |
| 308 | Water accumulation observed due to undulation observed on bridge top & Quarter deck. Hull survey for the same to be undertaken. Certificate for the same to be provided to ship. Repair/renew the plates if found necessary. Do as necessary to avoide accumulation of water. |
| 309 | Survey of tank top and tank side of both DB tanks in sat control room and DDC area. Renew /repair as found necessary. Job involves degutting and regutting of fittings of diving equipments. |
| 310 | Survey of both funnels area to be undertaken. Repair/renew if found necessary. |
| 311 | Survey of ref plant area and engine room catwalk area to be undertaken. Repair/renew if found necessary. |
| 312 | Survey of top area of containers to be undertaken. Renew repair if found necessary. |
| 313 | Anticipated build up of corroded, pitted area post survey |
| 314 | Anticipated renewal of MS plate post survey of the area. |
| 315 | Cutting of left unwanted metal from UW external hull to be undertaken |
| 316 | Brass tallies of the following to be manufactured and fitted as per sample or drawings with engraving as indicated by ships staff. Compartment tallies -50, Tank cover tallies -40, Lifting appliances tallies -20, Breather pipe tallies -50 and Mushroom heads tallies-20 . |
| 317 | Nireekshak name board at gangway damaged/broken to be repaired /renewed as per existing dimension. Mat-wood and brass |
| 318 | wire mesh of tank breather pipe perished, damaged. To be renewed and fitted in situ. Material-SS wire mesh. Qty-40 |
| 319 | Fixed shoring arrangement along with fixed shore damaged broken to be renewed as per existing dimension. |
| 320 | Fire hydrants mark and hose basket marking at scattered locations to be undertaken as per existing specification. Qty-35 |
| 321 | Watertight risk and control marking on doors and hatches damaged perished to be undertaken as per existing specification qty- 24 |
| 322 | Securing arrangement for AFFF, CO2, DCP extinguishers and FB 5x along with AFFF container post corroded or damaged or broken to be renewed at various locations. |
| 323 | Securing arrangement for ELBA post corroded or damaged or broken to be renewed at various locations. |
| 324 | Securing arrangement or installation of galley fire fighting system damaged broken to be renewed as per existing dimension and specification. |
| 325 | Securing arrangement for DD pump and BA charging compressor corroded thinned and holed. To be renewed as per dimension. |
| 326 | Hinges and securing hooks of basic boxes damaged broken to be renewed as per existing dimension. |
| 327 | Location marking tallies of various compartments to be renewed as per existing specification. |
| 328 | Hose basket for fire hoses corroded thinned and broken to be renewed and fitted as per dimension |
| 329 | Opening and fitment of panelling at various place to be undertaken for carry out various work.Renewal of damaged bulkhead/dech head panelling to be undertaken if required |
| 330 | Repair of various husbandry tools to be undertaken. Cordless impact screw driver-03, Cordless drill machine-02, Power drill machine-03, and cordless impact wrench with socket-02. Rivet Gun-02, 5 \\" angle grinder - 03, Cordless Grinder - 04. qty-29 |
| 331 | Load test of triangular plate for towing rope to be undertaken. SWL-20 Ton |
| 332 | Visual survey of towing rope (64) mm hawser to be undertaken. |
| 333 | Load test of towing shackles to be undertaken. |
| 334 | Load test of 32 mm towing pendent be undertaken. SWL-2 Ton |
| 335 | Load test of towing slip be undertaken. SWL-12.5 Ton |
| 336 | Load test of 32 mm chapping piece be undertaken. SWL-20 Ton |
| 337 | Renewal of 10 in nos slings for hoisting of various equipments. |
| 338 | Manufacturing of foldable Ty shade for quarter master to be undertaken. |
| 339 | Manufacturing of duplicate key of various locks as per sample. |
| 340 | GRP Coating on top of 04 man hole cover damaged or perished to be renewed in situ. |
| 341 | Servicibility and upgradation of L RAD (Long range acoustic device). |
| 342 | Canopies cover of sentry post faded/damaged to be renewed. |
| 343 | Empty collector of LMG damaged/broken to be renewed. |
| 344 | Empty collector of HMG damaged/broken to be renewed. |
| 345 | Empty collector of MMG damaged/broken to be renewed. |
| 346 | 01 in no Ceremonial dice damaged broken to be renewed. Mat-wood |
| 347 | Extension/ RE location of Ben Berry plateform in ship Galley. |
| 348 | Aata kneeding machine found defective, to be renewed |
| 349 | Foundation of Four hot plate, two hot plate and deep fat frier perished/ broken to be renewed. |
| 350 | Fitment of Aqua guard in ships galley to be undertaken and connection of fresh water supply to be provided for the same |
| 351 | Wooden cupboard to be replaced with CRCA cupboard in ship's galley as per sample i.a.w NHQ/DNA policy. |
| 352 | Light stand in ships galley corroded/ perished to be repaired/ renewed. |
| 353 | Locker for stowage of utensil in ships galley broken to be renewed as per sample |
| 354 | Deck drain pipeline of Ships galley to be chemically cleaned. Job involves removal of all drain line and fitment of the same pipe lines post chemical cleaning. Qty-25 Rmtr. |
| 355 | Foundation of small fridge in wardroom pantry corroded/ perished to be repaired. |
| 356 | Door/ Shutter for serving window damaged/ broken to be repair/ renewed. Qty - 02 Nos, Mat - SS |
| 357 | Survey & Load test of deck eyes at various location in engine room and shaft tunnel to be undertaken |
| 358 | Ventilation trunking perished/ holed to be repair/ renewed at various location |
| 359 | RU locker for stowage of hygiene item corroded/ perished to be repaired/ renewed as per various sample |
| 360 | Shop dispencer stand at JS, SS and Officer bathroom broken, to be repaired/ renewed |
| 361 | Mic connection box cover corroded, to be repair/ renewed. Mat - MS |
| 362 | CCTV base foundation perished at scattered location, to be renewed. Mat - MS |
| 363 | Diving intercom mic connection box and speaker foundation perished, to be renewed. Mat - MS |
| 364 | Mic connection box and speaker base with cover at Q deck and Foxle corroded, to be repair/ renewed. Mat - MS |
| 365 | Stiching of canvas cover for following :- (a) side scan sonar - 01 (b) gyro repeaters - 04 |
| 366 | Deflector sheets on pipe lines near electrical equipment broken at various location, to be renewed. |
| 367 | Stowage box for battries perished at scattered location, to be renewed. Mat- MS |
| 368 | Foundation of general lights at various location perished, to be renewed. Mat- MS |
| 369 | Hinges of control panel cover and junction box perished, to be renewed. Mat- MS |
| 370 | Ventilation trunking corroded/pershied, to be repaired/manufactured in SRE and equipment room. Mat - AL |
| 371 | Assistance required for maintenance of UW compartment for offering to HITU in Dry Dock (i) Surface preparation to ST 3 |
| 372 | (ii) Maintenance painting (paint will be provided by ship) |
| 373 | HULL - PART III |
| 374 | ABER replacement of Single Arm boat davit to be undertaken. Equipment BOM to be supplied by IN and installation material to be supplied by shipyard. Installation, STW, commissioning and trials under OEM supervision to be catered by the shipyard. Scope of work is as follows:- Scope of work-(a) Removal of entire existing cable, control panel and supply panel alongwith clamp , securing bracket and associated fittings.(b) Removal of existing Boat Davit with associated fittings.(c) Installation of New Boat Davits with a associated fittings including control panel. (d) Fitment and calibration of limit switches on both davits.(e) Cabling and wiring to be caried out.(f) Fitment of new SWR.(g) Fitment of limit switches with securing brackets. (h) Fitment of control panel, supply panel along with associated fittings(j) Restoration of paint scheme iaw NO-53/16.(k) Undertake modification required for installation of boat davit along with associated fittings. (m) Fitment of addition strengthing members for boat davit.(n) Undertake Load test of both davits and safety preventor iaw INBR 1552(p) Supply and fitment of instruction tallies, operating procedure plates and load test tallies.(q) Degutting and Regutting of lagging in affected area post completion of hot work.(r) Fitment of ladder/ stand for easy access to undertake repair.(s) Proving of HATs/ SATs of system post fitment and certificate to be provided.(t) Serviciability checks of ARH to be carried out and certificate to be provided. |
| 375 | ABER replacement of Hydraulic Anchor Winch to be undertaken. Equipment BOM to be supplied by IN and installation material to be supplied by shipyard. Installation, STW, commissioning and trials under OEM supervision to be catered by the shipyard. Scope of work is as follows:- (i) De-gutting and removal of existing Hydraulic Anchor Winch with associated fittings like:-(a) De-gutting and removal of Hydraulic Tank from E/R. Capacity-4000 ltrs(b) De-gutting and removal of Hydraulic Lines running from Tanks to the system. Length-200 RMT(c) De-gutting and removal of foundations, supporting brackets, securing clamps etc(d) De-gutting and removal of Local control panel including all fittings from Winch deck(e) De-gutting and removal of Remote control panel including all fittingsand cables(f) Removal of Motors with pumps including starter panels and Cables(Local and Remote). Qty-06(g) Removal of Existing SWR, Length-400 M each, Qty-02(h) Removal of existing tensionometer and supporting clamps including all sensors and load cells(j) Removal of laggings, panels and misc fittings. which are affecting hot work areas(ii) Fitment of new Anchor Winch with associated fittings like:-(a) Manufacturing and fitment of foundations suitable to new Anchor Winch, Qty-02(b) Fitment of new electric driven horizontal anchor winch along with associated fittings (i.e. 25HP electric motor with electromagntic brake, reduction gearbox, Band brake assembly, Dog clutch for main shaft, Spooling, Control panel, Bridge/ Remote control console, Local control console and DBR Box). Qty-02(c) Supply and fitment of instruction tallies, operating procedure plates and load test tallies for both(d) Fitment of tensionometer and supporting clamps including all sensors and load cells with display unit(e) Fitment of additional strengthning member, supporting brackets, securing clampss wherever required for installation of the system.(f) Post completion of hot work, Restoration of lagging, Panelling and appropriate paint scheme as per NO 53/16 in affected areas including foundations and Anchor Winch with all associated securing arrangements(g) Supply of one set of instlation and commissioning tools, jigs and fixtures(h) Supply and fitment of safety switches. (j) Supply and fitment of new control panel with cabling(k)Supply and laying of all cables pertaining to the system for remote and local both the operation.(m) Proving of HATs/ SATs of the system post fitment iaw NCD 3901 and certificates to be provided. (n) Carry out load test of Anchor Winch with SWR iaw INBR 1552. (p) Undertake modification required for fitment of control panel, remote panel , cable route and other fittings.(q) Resolution of installation issues faced post fitment while operation during guarantee period to be catered by shipyard (r)/Manufacture/ fittment of chequred plate with foundation post de gutting of hydraulic oil tank. Mat- MS/AL. Area- 20 sqmtr(s) Renwal of steel (DMR 249 A) considering de gutting and fittment of new anchor winch foundation with supporting brackets. Qty- 2 Ton |
| 376 | ENGINEERING - PART I |
| 377 | Both Main Engines Carry out 1000 hourly routines on Both Main engine as per maintop no MT 23015:1000H3 - Check and adjust temperature and pressure switches: Renew switches: |
| 378 | Carry out annual routines on Both main engine as as per maintop no MT 23015: A1-Carry out SOAP analysis of Both Main engine and gear box oil samples: |
| 379 | Carry out 3000 hourly routines on Both Main engine as per maintop no MT 23015:3000H1 - Check over speed protection and automatic stop: |
| 380 | Carry out 5000 hourly routines on Both Main engine as per maintop no MT 23015:5000H1- Check and adjust inlet and exhaust valve clearances |
| 381 | 5000H2-U/T spot checks of fuel cams/ inlet and exhaust cams withdrive |
| 382 | 5000H3- U/T spot checks of camshaft drive with gear wheels |
| 383 | 5000H4- Lubricate pilot starting air distributer with drive. |
| 384 | 5000H5- U/T spot checks of governor drive |
| 385 | 5000H6- Clean charge air cooler, air intake side and water side |
| 386 | 5000H7- U/T spot checks of flexible gear wheel, pump drive (pumpend) |
| 387 | 5000H8- U/T spot checks of flexible coupling |
| 388 | 5000H9- Calibrate temperature and pressure gauges. |
| 389 | 5000H10- ndertake spot checks of fuel injection pump drive |
| 390 | 5000H11- Clean fuel injector nozzle holder |
| 391 | 5000H12- Replace fuel injector nozzle |
| 392 | 5000H13- U/T Spot checks of fuel injection pump erosion plug |
| 393 | 5000H14- Check flexible fuel connections |
| 394 | 5000H15- Check crankshaft deflection: (Also check before and afterevery major overhaul/docking). Record the reading in servicelog. |
| 395 | 5000H16- Check lubricating oil priming pump(electrical). |
| 396 | 5000H17- Clean valve gear lub oil system strainer |
| 397 | 5000H18- Check all exhaust manifold bellows |
| 398 | 5000H20- Check sea water pump with drive. |
| 399 | Carry out 10000 hourly routines on Both Main engine as per maintop no MT 2301510000H1- Overhaul inlet and exhaust valves and valve guides. Changethe parts if necessary |
| 400 | 10000H2- Overhaul air starting valves |
| 401 | 10000H3- U/T spot checks of camshaft bearing and thrust washers |
| 402 | 10000H4- Overhaul valve gear system for inlet and exhaust valve |
| 403 | 10000H5- Overhaul/replace inlet and exhaust valve/ valve seatsaccording to wear |
| 404 | 10000H6- Check indicator valves |
| 405 | 10000H7- Replace flexible fuel connections |
| 406 | 10000H8- U/T spot checks of cooling water pump drive |
| 407 | 10000H9- Overhaul sea water pump |
| 408 | Both Main engine lub oil System Carry out SR routine on both main engine lub oil system as per Maintop no MT- 23115 and 23141 which include following(a) SR1-Dismantle, chemically clean and pressure test the cooler upto 1.5 times of working pressure. |
| 409 | (b) SR2-Dismantle and clean the thermostat valve. |
| 410 | Both Main engine Fuel oil SystemSR2- (a) Refit all remote operated quick closing valves fitted on service and settling tanks: Job involves remove ,overhaul, pressure test and fitment including replacement of required spares: Size - 32 mm ,(b) Renew the defective valves: (Shipyard to quote separately for both the serials: Payment at actual) |
| 411 | Both Main engine intake and exhaust systemCarry out SR routine on both main engine intake and exhaust system as per Maintop which include followingSR2- Check non metallic part pipes, muffler and exhaust line for cracks and distortion, Renew the defective parts: |
| 412 | SR3- Check and adjust alignment of compensator adjust as necessary during fitment: |
| 413 | SR5- Remove and inspect the lub oil drain cock of the exhaust gas expansion piece and clean it by blowing through compressed air (if applicable): |
| 414 | SR6- Check and grease all support hangers of air induction and exhaust system: |
| 415 | SR7-Calibrate the thermo couples and temperature indicators (if fitted): Exhaust Thermo couple range - 0 to 600°C Qty - 32 Intake thermo couple range - 0 to 70°C Qty - 04 |
| 416 | SR9- Application and restoration of recommended paint schemeon all components of the air intake and exhaust system: |
| 417 | SR10- (a) Inspect and clean all components of Air Induction System from weather deck opening to TC Rubber bellow:(b) Replace air filter: Yard to quote the spares |
| 418 | Carry out occassional routine on both main engine intake and exhaust system as per Maintop no MT 233000 which include following:-O3 - Whenever any repair / renewal of exhaust sytem is undertaken, the renewal/ repaired system must be pressure tested up to 1:5 kg/cm2 times the working pressure, i:e 4:5 bar: |
| 419 | Both Main engine S/W circulating systemSR2- Calibrate all pressure gauges: Suction press - (-1 to10) bar Qty - 02, Discharhe Range - (0 -10) bar, Qty - 08 bar |
| 420 | Main shaftingCarry out SR routine on both main propulsion shaft line as per Maintop no MT 27022 which include followingSR1- Survey and Repair of protective coating of tail shaft: |
| 421 | SR2- Carry out visual check of all external bolts, locking strips and wire: |
| 422 | SR3- Check condition of anodes, Renew the anodes eroded more than 50%: |
| 423 | SR4- Check condition of shaft balance pad: Note: remove pads when approx 2 mm of lining remains: |
| 424 | SR1- Undertake sample inspection of Plummer bearings on each shaft line for scoring/corrosion: In case any abnormality observed, carry out inspection of balance plummer bearings on the same shaft line: |
| 425 | SR4- Renew and Carry out calibration of remote and local temperature indicator : Range 0 to 110 Degree Celsius: (Yard to quote the spares) |
| 426 | Ships Firemain systemSR1- Renew all leaking plug, butterfly and ball valves: |
| 427 | SR2- Refit / repair leaking valves other then the plug / butterfly and ball valves: Size- 65 mm Qty- 05 |
| 428 | Ships fuel systemSR8- Check operation of hand pumps in the system and overhaul,if required: |
| 429 | SR11-Overhaul of all quick shut off valves of fuel system: |
| 430 | Ships Freshwater systemSR1- Visually examine entire length of hot lagging for domestic hot water system and renew as necessary: |
| 431 | SR2- Refit Defective valves in the system: Size 32 mm (SDNR)- 03, Size 50 mm (SDNR)-03, Size 25 mm- 04 |
| 432 | SR5- Calibrate automatic cut-in and cut-out mechanism ofhydrophore tanks (as applicable Range- cut in 1:7 bar, cut out 3:2 bar |
| 433 | SR6- Refit and calibrate relief valve in the hydrophore tankpneumatic charging system (if applicable) Qty-02, set Value - 6 bar |
| 434 | HP AIR SYSTEMSR1- Calibration/ Checks correct functioning of system relief valves. (INBR 3000 Art 2302). Qty-02, set Value - 5 bar, Qty - 06 Set value 8:5 Bar, Qty - 07 Set value 31 bar: |
| 435 | SR5- Replace all leaking plug/butterfly valves. |
| 436 | Fuel oil centrifugeCarry out Annual routines as follows:-A1 Check treads of inlet pipe and of oil pairing disc for damage and wear |
| 437 | A2 Check inlet device(a) Check the flow indicator if clogged: Clean the sight glass:(b) Check the reducing valve cone for scratches and play:(c) Check the non return valve cone for scratches and play: |
| 438 | A3 Dismantle and examine sepearator bowl assembly thoroughly: Clean all components and checks following:-(a) Check disc stack pressure(b) Checks for corrosion, erroision and cracks(c) Galling of guide surface |
| 439 | A4 Renew oil in gear housing: Check the teeth of worm wheel and worm for wear: |
| 440 | Lub oil centrifugeCarry out Annual routines as follows:-A1 Check treads of inlet pipe and of oil pairing disc for damage and wear |
| 441 | A2 Check inlet device(a) Check the flow indicator if clogged: Clean the sight glass:(b) Check the reducing valve cone for scratches and play:(c) Check the non return valve cone for scratches and play: |
| 442 | A3 Dismantle and examine sepearator bowl assembly thoroughly: Clean all components and checks following:-(a) Check disc stack pressure(b) Checks for corrosion, erroision and cracks(c) Galling of guide surface |
| 443 | A4 Renew oil in gear housing: Check the teeth of worm wheel and worm for wear: |
| 444 | Gear box lub oil pump SR1- Carry out performance trial of the pump including parameterchecks (suction/ discharge pressure), vibration trials,insulation/ SPM checks on motor, motor starting-runningcurrent checks etc. Assess for satisfactory performance and defects, it any. Overhaul pump if performance is suboptimal |
| 445 | SR2- Inspect condition of suction/ discharge compensators.Renew as necessary. |
| 446 | SR3- Calibrate all instrumentation Main oil pressure gauge - (0 to 70) bar Qty - 02, Clutch oil pressure gauge - (0 to 40) bar Qty - 02, Bearing oil pressure gauge - (2:5 to 3:0) bar Qty - 02, GB cooler pressure gauge - (0 to 70) bar Qty - 02: Pressure transmitter - (0 to 70) bar Qty - 02, (0 to 40) bar Qty - 02, (0 to 10) bar Qty - 02, Temperature transmitter - (0 to 100) °C Qty - 02, (0 to 110) °C Qty - 04 Pressure switches - 08 |
| 447 | SR4- Carry out functional test of relief valve. Reset to specifiedlifting pressure. Relief valve pressure - 45 bar Qty - 02, Main oil pressure - (27 to 30) bar Qty - 02, Clutch oil pressure - (25 to 27) bar Qty - 02, Bearing oil pressure - (2:5 to 3:0) bar Qty - 02 |
| 448 | SR5- Inspect the suction strainer. Renew if required |
| 449 | SR7- Refit suction and discharge valves. |
| 450 | SR8-Check condition of coupling guards. Repair/ replace ifrequired. |
| 451 | Fuel Oil Transfer PumpSR1- Carry out performance trial of the pump including parameter checks (suction/ discharge pressure), vibration trials, insulation/ SPM checks on motor, motor starting-running current checks etc. Assess for satisfactory performance and defects, it any. Overhaul pump if performance is suboptimal |
| 452 | SR2- Inspect condition of suction/ discharge compensators.Renew as necessary. |
| 453 | SR3- Calibrate all instrumentation |
| 454 | SR4- Carry out functional test of relief valve. Reset to specified lifting pressure |
| 455 | SR5- Inspect the suction strainer. Renew if required |
| 456 | SR7- Refit suction and discharge valves. |
| 457 | SR8-Check condition of coupling guards. Repair/ replace ifrequired. |
| 458 | Main engine lub oil priming pump SR1- Carry out performance trial of the pump including parameter checks (suction/ discharge pressure), vibration trials, insulation/ SPM checks on motor, motor starting-running current checks etc. Assess for satisfactory performance and defects, it any. Overhaul pump if performance is suboptimal |
| 459 | SR2- Inspect condition of suction/ discharge compensators. Renew as necessary. |
| 460 | SR3- Calibrate all instrumentation |
| 461 | SR4- Carry out functional test of relief valve. Reset to specifiedlifting pressure |
| 462 | SR5- Inspect the suction strainer. Renew if required |
| 463 | SR7- Refit suction and discharge valves. |
| 464 | SR8-Check condition of coupling guards. Repair/ replace ifrequired. |
| 465 | Fuel oil cargo pump (MT 31200)SR1- Carry out performance trial of the pump including parameter checks (suction/ discharge pressure), vibration trials, insulation/ SPM checks on motor, motor starting-running current checks etc. Assess for satisfactory performance and defects, it any. Overhaul pump if performance is suboptimal |
| 466 | SR2- Inspect condition of suction/ discharge compensators. Renew as necessary. |
| 467 | SR3- Calibrate all instrumentation |
| 468 | SR4- Carry out functional test of relief valve. Reset to specifiedlifting pressure |
| 469 | SR5- Inspect the suction strainer. Renew if required |
| 470 | SR7- Refit suction and discharge valves. |
| 471 | SR8-Check condition of coupling guards. Repair/ replace if required. |
| 472 | AC S/W Pump (Port & Stbd)A2 Check alignment between pump and motor (applicable for coupled pumps): Re-align if required: This routine is to be carried out in the event that alignment checks have not been carried out as part of any repair work on pump-motor in the preceding one year: Note:- Routines A1 & A2 is to be conjoined with refit incase refit is falling due in the year: Man-hours : Two |
| 473 | SR1 Carry out performance trial of the pump including parameter checks(suction/discharge pressure), vibration trials, insulation/SPM checks on motor, motor starting-running current checks etc: Assess for satisfactory performance and defects, if any: Man-hours : One |
| 474 | SR2 Calibrate all instrumentation: Suction Gauge - ( -1 to 10) bar, Qty - 02 Discharge gauge - ( 0 to 10) bar, Qty - 02 |
| 475 | SR3 Inspect and renew if required the suction strainer: |
| 476 | General Service PumpCarry out annual routine as per maintop: Following to be checked:-A2 Check alignment between pump and motor (applicable for coupled pumps): Re-align if required: This routine is to be carried out in the event that alignment checks have not been carried out as part of any repair work on pump-motor in the preceding one year: Note:- Routines A1 & A2 is to be conjoined with refit incase refit is falling due in the year: Man-hours : Two |
| 477 | SR1 Carry out performance trial of the pump including parameter checks(suction/discharge pressure), vibration trials, insulation/SPM checks on motor, motor starting-running current checks etc: Assess for satisfactory performance and defects, if any: Man-hours : One |
| 478 | SR2 Calibrate all instrumentation: Suction Gauge - ( -1 to 7) bar, Qty - 01 Discharge gauge - ( 0 to 10) bar, Qty - 01 |
| 479 | SR3 Inspect and renew if required the suction strainer: |
| 480 | Carry out annual routine as per maintop: Following to be checked:-A2 Check alignment between pump and motor (applicable for coupled pumps): Re-align if required: This routine is to be carried out in the event that alignment checks have not been carried out as part of any repair work on pump-motor in the preceding one year: Note:- Routines A1 & A2 is to be conjoined with refit incase refit is falling due in the year: Man-hours : Two |
| 481 | SR1 Carry out performance trial of the pump including parameter checks(suction/discharge pressure), vibration trials, insulation/SPM checks on motor, motor starting-running current checks etc: Assess for satisfactory performance and defects, if any: Man-hours : One |
| 482 | SR2 Calibrate all instrumentation: Suction Gauge - ( -1 to 7) bar, Qty - 01 Discharge gauge - ( 0 to 10) bar, Qty - 01 |
| 483 | SR3 Inspect and renew if required the suction strainer: |
| 484 | Carry out annual routine as per maintop: Following to be checked:-A2 Check alignment between pump and motor (applicable for coupled pumps): Re-align if required: This routine is to be carried out in the event that alignment checks have not been carried out as part of any repair work on pump-motor in the preceding one year: Note:- Routines A1 & A2 is to be conjoined with refit incase refit is falling due in the year: Man-hours : Two |
| 485 | SR1 Carry out performance trial of the pump including parameter checks(suction/discharge pressure), vibration trials, insulation/SPM checks on motor, motor starting-running current checks etc: Assess for satisfactory performance and defects, if any: Man-hours : One |
| 486 | SR2 Calibrate all instrumentation: Suction Gauge - ( -1 to 10) bar, Qty - 01 Discharge gauge - ( 0 to 10) bar, Qty - 0 |
| 487 | SR3 Inspect and renew if required the suction strainer: |
| 488 | Carry out annual routine as per maintop: Following to be checked:-A2 Check alignment between pump and motor (applicable for coupled pumps): Re-align if required: This routine is to be carried out in the event that alignment checks have not been carried out as part of any repair work on pump-motor in the preceding one year: Note:- Routines A1 & A2 is to be conjoined with refit incase refit is falling due in the year: Man-hours : Two |
| 489 | SR1 Carry out performance trial of the pump including parameter checks(suction/discharge pressure), vibration trials, insulation/SPM checks on motor, motor starting-running current checks etc: Assess for satisfactory performance and defects, if any: Man-hours : One |
| 490 | SR2 Calibrate all instrumentation: Suction Gauge - ( -1 to 10) bar, Qty - 02 Discharge gauge - ( 0 to 10) bar, Qty - 02 |
| 491 | Carry out annual routine as per maintop: Following to be checked:-A2 Check alignment between pump and motor (applicable for coupled pumps): Re-align if required: This routine is to be carried out in the event that alignment checks have not been carried out as part of any repair work on pump-motor in the preceding one year: Note:- Routines A1 & A2 is to be conjoined with refit incase refit is falling due in the year: Man-hours : Two |
| 492 | SR1 Carry out performance trial of the pump including parameter checks(suction/discharge pressure), vibration trials, insulation/SPM checks on motor, motor starting-running current checks etc: Assess for satisfactory performance and defects, if any: Man-hours : One |
| 493 | SR2 Calibrate all instrumentation: Suction Gauge - ( -1 to 5) bar, Qty - 01 Discharge gauge - ( 0 to 7) bar, Qty - 01 |
| 494 | Carry out annual routine as per maintop: Following to be checked:-A2 Check alignment between pump and motor (applicable for coupled pumps): Re-align if required: This routine is to be carried out in the event that alignment checks have not been carried out as part of any repair work on pump-motor in the preceding one year: Note:- Routines A1 & A2 is to be conjoined with refit incase refit is falling due in the year: Man-hours : Two |
| 495 | SR1 Carry out performance trial of the pump including parameter checks(suction/discharge pressure), vibration trials, insulation/SPM checks on motor, motor starting-running current checks etc: Assess for satisfactory performance and defects, if any: Man-hours : One |
| 496 | SR2 Calibrate all instrumentation: Suction Gauge - ( -1 to 7) bar, Qty - 01 Discharge gauge - ( 0 to 10) bar, Qty - 01 |
| 497 | Carry out annual routine as per maintop: Following to be checked:-A2 Check alignment between pump and motor (applicable for coupled pumps): Re-align if required: This routine is to be carried out in the event that alignment checks have not been carried out as part of any repair work on pump-motor in the preceding one year: Note:- Routines A1 & A2 is to be conjoined with refit incase refit is falling due in the year: Man-hours : Two |
| 498 | SR1 Carry out performance trial of the pump including parameter checks(suction/discharge pressure), vibration trials, insulation/SPM checks on motor, motor starting-running current checks etc: Assess for satisfactory performance and defects, if any: Man-hours : One |
| 499 | SR2 Calibrate all instrumentation: Suction Gauge - ( -1 to 7) bar, Qty - 02 Discharge gauge - ( 0 to 10) bar, Qty - 02 |
| 500 | Carry out annual routine as per maintop: Following to be checked:-A2 Check alignment between pump and motor (applicable for coupled pumps): Re-align if required: This routine is to be carried out in the event that alignment checks have not been carried out as part of any repair work on pump-motor in the preceding one year: Note:- Routines A1 & A2 is to be conjoined with refit incase refit is falling due in the year: Man-hours : Two |
| 501 | SR1 Carry out performance trial of the pump including parameter checks(suction/discharge pressure), vibration trials, insulation/SPM checks on motor, motor starting-running current checks etc: Assess for satisfactory performance and defects, if any: Man-hours : One |
| 502 | SR2 Calibrate all instrumentation: Suction Gauge - ( -1 to 10) bar, Qty - 02 Discharge gauge - ( 0 to 10) bar, Qty - 02 |
| 503 | SR3 Inspect and renew if required the suction strainer: |
| 504 | Carry out annual routine as per maintop: Following to be checked:-A2 Check alignment between pump and motor (applicable for coupled pumps): Re-align if required: This routine is to be carried out in the event that alignment checks have not been carried out as part of any repair work on pump-motor in the preceding one year: Note:- Routines A1 & A2 is to be conjoined with refit incase refit is falling due in the year: Man-hours : Two |
| 505 | SR1 Carry out performance trial of the pump including parameter checks(suction/discharge pressure), vibration trials, insulation/SPM checks on motor, motor starting-running current checks etc: Assess for satisfactory performance and defects, if any: Man-hours : One |
| 506 | SR2 Calibrate all instrumentation: Suction Gauge - ( -1 to 5) bar, Qty - 02 Discharge gauge - ( 0 to 7) bar, Qty - 02 Pressure switch ( 0 to 7) bar Qty- 02 |
| 507 | (A) Carry out 2000 hourly routine on DA 2 & 3 as follows:-2000H3- Inspect the flexible coupling for cracks and check alignment. |
| 508 | 2000H4- Check fuel injection pump timing. |
| 509 | 2000H6- Calibrate fuel injectors. Reset injection spray pressure to 170-180 kg/sq.cm. pressure |
| 510 | 2000H12- Check alignment between engine and alternator. Adjust asnecessary |
| 511 | 2000H13- Check operation of thermostat valve on lub oil cooler andheat exchanger. Renew if necessary. |
| 512 | 2000H14- Chemically clean, renew all 'O' seals and gaskets. Pressuretest following to the pressure mentioned against each :-(a) Heat ExchangerSeawater side 4.0 Kg/sq.cm.Fresh water side 4.0 Kg/sq.cm.(b) Oil coolerOil side 10.0 Kg/sq.cm.Water side 04.0 Kg/sq.cm.(c) Inter coolerAir side 2.5 Kg/sq.cm.Water side 4.0 Kg/sq.cm. |
| 513 | 2000H17- Throughly clean turbocharger on both turbine andcompressor sides. Examine turbine blade and compressorwheel for damage. Clean diffuser |
| 514 | 2000H20- Check insulation blankets of turbo supercharger air andexhaust system. Renew if necessary. |
| 515 | 2000H24- Check crankshaft end clearances |
| 516 | 2000H26- Renew zinc anode on heat exchanger,after cooler andexhaust manifold. |
| 517 | 2000H28-Check and inspect drive gears for camshaft and auxiliaries |
| 518 | (A) Carry out 8000 hourly routine on DA 1 and 4, which also include 2000 hourly, 4000 hourly routine:-2000H3- Inspect the flexible coupling for cracks and check alignment. |
| 519 | 2000H4- Check fuel injection pump timing. |
| 520 | 2000H6- Calibrate fuel injectors. Reset injection spray pressure to 170-180 kg/sq.cm. pressure |
| 521 | 2000H12- Check alignment between engine and alternator. Adjust asnecessar |
| 522 | 2000H13- Check operation of thermostat valve on lub oil cooler andheat exchanger. Renew if necessary. |
| 523 | 2000H14- Chemically clean, renew all 'O' seals and gaskets. Pressuretest following to the pressure mentioned against each :-(a) Heat ExchangerSeawater side 4.0 Kg/sq.cm.Fresh water side 4.0 Kg/sq.cm.(b) Oil coolerOil side 10.0 Kg/sq.cm.Water side 04.0 Kg/sq.cm.(c) Inter coolerAir side 2.5 Kg/sq.cm.Water side 4.0 Kg/sq.cm. |
| 524 | 2000H17- Throughly clean turbocharger on both turbine andcompressor sides. Examine turbine blade and compressorwheel for damage. Clean diffuser |
| 525 | 2000H20- Check insulation blankets of turbo supercharger air andexhaust system. Renew if necessary. |
| 526 | 2000H24- Check crankshaft end clearances |
| 527 | 2000H26- Renew zinc anode on heat exchanger,after cooler andexhaust manifold. |
| 528 | 2000H28-Check and inspect drive gears for camshaft and auxiliaries |
| 529 | 4000H1- Carry out 2000 Hourly routines.Note: Record all measured dimensions and clearances in theengine log. |
| 530 | 4000H2- Remove all cylinder heads and dismantle valve gear: Decarbonise combustion spaces: Grind in valves: Check condition of valve guide and valves: Renew as necessary |
| 531 | 4000H3- Examine condition of valve gear bracket, parts and valve seat inserts: Renew as necessary: |
| 532 | 4000H4- Renew cylinder head joints, flexible hoses and cover joints: |
| 533 | 4000H5-Remove one piston assembly and cylinder liner at random and measure and record following in the engine log:a) Piston ring clearancesb) Gauge liner internally for abnormal wear, pitting and corrosion of external surfaces:c) Big end bearing shells and crankpin for clearances and ovality respectively:Note:-In case wear/ corrosion is abnormal, examine all cylinder liners and renew parts as required: |
| 534 | 4000H6- Carry out water pressure test under gravity head from over head tank: Check bottom of the liners through crank case door for leakage: |
| 535 | 4000H7- Examine pins and bushes of fuel control mechanism: |
| 536 | 4000H8- Calibrate fuel injection pump: Overhaul if necessary: |
| 537 | 4000H9- Calibrate low lub oil pressure and high temperature protection devices: |
| 538 | 4000H10- Overhaul the pumps: Renew worn parts as necessary: |
| 539 | 4000H11-Calibrate all temperature and pressure gauges: |
| 540 | 4000H13- Inspect valves and rings of air starting valves: Renew if necessary |
| 541 | 4000H14- TURBOCHARGERCheck condition and measure bearing clearances, overhaul if necessary:PRE 8000 HOURLY ROUTINES:Check compression pressures of all cylinders, it should be more than 19 bar: Renew piston rings of all those cylinders not confirming to specified compression pressure during 8000 Hourly routines: |
| 542 | 4000H15- Check and inspect drive gears for camshaft and auxiliaries: |
| 543 | 8000H1- MAJOR INSPECTIONCarry out 4000 Hourly routines:Note: Record all measured dimensions and clearances in the engine log: |
| 544 | 8000H2- Remove all piston assemblies, decarbonise pistons and check ring clearances, renew piston rings as necessary: |
| 545 | 8000H3- Measure big end bearing clearances and examine bearing shells, their bolts, nuts and washers: Renew if necessary: |
| 546 | 8000H4-Examine crank pin surfaces for scoring and check for ovality: |
| 547 | 8000H5- Carry out crack detection test of gudgen pin, piston and cam shafts: |
| 548 | 8000H6- Gauge all liners internally, extract one liner from each bank and examine for external corrosion and pitting: If required extract all liners and renew as necessary: |
| 549 | 8000H7- Remove and refit overspeed trip gear: |
| 550 | 8000H8- Check condition of cam shaft: Examine push rod sleeves,roller tappets and renew if necessary: |
| 551 | 8000H9- Check all connecting rods for bend and twist: Clean andflush oil passages: |
| 552 | 8000H10- Check torsional vibration damper: |
| 553 | 8000H11- Overhaul fuel feed pump and renew all seals |
| 554 | 8000H12- Overhaul fuel injection pump, check governor assembly and renew the parts in case of excessive wear: Renew all seals and 'O' rings: Calibrate fuel pump and governor assembly together: |
| 555 | 8000H13- Overhaul turbo supercharger, renew the bearings: Renew entire unit if parts are excessively worn: |
| 556 | 8000H14-Check operation of all alarms and safety devices: Reset asnecessary: |
| 557 | 8000H15- Renew all flexible hoses: |
| 558 | 8000H16- Check air starting valve and clean starting air distributor: |
| 559 | 8000H17- Carry out water pressure test of cooling water chambers and check for leaks (especially the packing of cylinder liners against the crank case: |
| 560 | Carry out SR routine on Diesel Alternator1,2,3 & 4 intake and exhaust system as per Maintop which include followingSR2- Check non metallic part pipes, muffler and exhaust line for cracks and distortion, Renew the defective parts: |
| 561 | SR3- Check and adjust alignment of compensator adjust as necessary during fitment: |
| 562 | SR5- Remove and inspect the lub oil drain cock of the exhaust gas expansion piece and clean it by blowing through compressed air |
| 563 | SR6- Check and grease all support hangers of air induction and exhaust system: |
| 564 | SR7-Calibrate the thermo couples and temperature indicators (if fitted) |
| 565 | SR8- Inspect for condition and overhaul cocks/ fittings for measurement of air intake depression and exhaust back pressure measurement in exhaust trunkings at appropriate locations: |
| 566 | SR9- Application and restoration of recommended paint schemeon all components of the air intake system: |
| 567 | SR10- (a) Inspect and clean all components of Air Induction System from weather deck opening to TC Rubber bellow:(b) Replace air filter: |
| 568 | Carry out occassional routine on Diesel Alternator1,2,3 & 4 intake and exhaust system as per Maintop no MT 23315 which include following:-O3 - Whenever any repair / renewal of exhaust sytem is undertaken, the renewal/ repaired system must be pressure tested up to 1:5 kg/cm2 times the working pressure: |
| 569 | Carry out occassional routine as follows:-O1-When the system has been assembled after repair work,blow through with dry nitrogen: Thereafter pressure test to15 Bar working presssure for 24 hours to check forleakage |
| 570 | O2 On completion of the pressure test, system is to bedehydrated by vacuum pump : On completion carry outvacuum test for 24 hours: |
| 571 | O3 After refit or major repair to the gas system or components,insert Nylon bags/felt filters in the suction screen and removeevery 24 hours of running for cleaning until gas system isproved clean:(Note:- Plant capacity will be reduced during this period) |
| 572 | O5 On each occasion that the compressor is decoupled from themotor, realign the compressor and check alignment:(Refer to INSMA Acquaint M6/66 Dated 11 Jul 14) |
| 573 | O7 Compressor oil seal to be checked for leakage duringrunning (limit 15 drops/Hr): In case oil leakage is excessive,schedule for renewal of shaft seal at the first availableopportunity: |
| 574 | O9 Test alarms and trip functions by simulation before starting: |
| 575 | O10 Inspect externally all the switches, push buttons, indicationlamps for any damage, dents, cracks and corrosion if any: |
| 576 | Carry out 4000 hourly routine as follows:- 4000H1-Check Compressor & Motor alignment for misalignment (specified limits Radial - 0:10mm, Axial - 0:076mm along with coupling gap of 140mm): If observed out of specified limits, realign the motor and compressor: |
| 577 | 4000H2- Check all system parameters like discharge /suction temperature, Chilled water & Sea water pressure: Carryout corrective actions if parameters are not within specified values: |
| 578 | 4000H3- Renew Compressor Oil: Type - SAVSYN2068 |
| 579 | 4000H4- Carry out greasing of driven and non-driven ends of motor (as applicable): |
| 580 | 4000H5- Check tightness of terminal connections in motor terminal box, soft starter panel and local control panel: Tighten connections if required with the assistance of electrical department personnel: |
| 581 | 4000H6- Check health of Motor Bearing by SPM Meter: Replace the bearings if readings observed out of specified limits: |
| 582 | 4000H7- Replace filter drier core for liquid injection line: |
| 583 | 4000H8- Check Differential pressure across oil filter element in duplex oil filter and clean the oil filter element if required: |
| 584 | 4000H9- Check tightness of holding down bolts/fasteners: Replace if found corroded: |
| 585 | 4000H10- Check functioning of expansion valves: Calibrate as required: |
| 586 | Carry out six monthly routines as per maintop which include followinhg:-6M2 - Check operation of pilot operated solenoid valves, capacity control solenoid valves and pressure switches for set points: Reset/ Calibrate/Replace if deviation observed: |
| 587 | Carry out annual routines as per maintop which include following:-A1 - Calibrate all gauges, panel modules and alarms /trip cutouts: |
| 588 | A3- Calibrate all Relief valves: Range - 15 bar |
| 589 | Carry out 8000 hourly routine as follows:-8000H1- Check compressor loading/unloading mechanism. Replacepiston seal and loading/unloading solenoid valves, ifrequired. |
| 590 | 8000H2- Check compressor Axial Thrust clearance (Inlet EndClearance). It should be as follows:-(a) XRV-204 Compressors.0.100 MM to 0.125MM. Replace all bearings if clearance>0.125MM.(b) XRV-127 compressors. 0.065 MM to 0.090MM Replace all bearings if clearance>0/0.090MM. |
| 591 | 8000H3- Check Compressor radial float of the bearing (inlet endjournal bearing) it should not be:-(a) XRV 204 <0.085mm(b) XRV 127 <0.015mmIn case the limits is exceeded replace bearing. |
| 592 | 8000H4- Check/Calibrate/Replace linear positioner indicator or limitswitch mechanism of compressor for proper loading/unloading mechanism. |
| 593 | 8000H7- Replace filters for POSV ‘s (Pilot Operated Solenoid Valves). |
| 594 | 8000H9- Carry out calibration of pressure, temp gauges, pressure transmitters, temperature transmitters, FKD 40-41 controller, and thermostatic expansion valve of liquid & liquid Injection line. |
| 595 | 8000H10- Carry out calibration of pressure & temp switches, thermostats, pressure safety valves, flow / DP gauges across chilled water & sea water for operation as per set points. |
| 596 | Carry out SR routines as per maintop which include following:-SR1 - Inspect chilled water pipe insulation: Renew where required: Gas line insulation required from plant to ATU's |
| 597 | SR2 - Check the water flow through condenser and refrigerant discharge pressure: In case flow is less than specified and discharge pressure is higher than normal, undertake insitu descaling of the condenser (chemically or mechanically): |
| 598 | SR3- Calibrate gauges & cut outs |
| 599 | SR4 - Overhaul and pressure testing of filter drier by pass valves: Type - Brassomatic Dia - 7/8'' |
| 600 | SR5 - Overhaul and pressure testing of sea water inlet and outletvalves of condenser: Type - Gate Valve, Dia - 100 mm |
| 601 | Carry out occassional routine as follows:-O1 - Clean Condenser tubes: |
| 602 | Carry out 800 and 2400 hourly routines as follows:-800H3 - Check All safety switches: If Set points are found disturbed,Carry out recalibration & resetting or replace the switch: |
| 603 | 800H4 - Check All the gauges for correctness of reading:Recalibrate or replace as required: |
| 604 | 2400H3 - Check Pipe line insulation: If Damaged, Replace it: |
| 605 | SR1- Completely remove fairing epoxy compound to inspect the stage of fasteners on the rudder: Renew the fasteners if deteriorated: Re-apply fairing epoxy compond post inspection/ DR:Note:- In addition to positive locking of fasteners, ensured by 'L' plates, split pins/ lock washers/ interlocking seizing wires are to be introduced: |
| 606 | SR3- Renew complete local wiring, in case of any major routines falling due on the steering gear system |
| 607 | Carry out SR routine as follows:-SR4-Ascertain the available quantity of Halon in the cylinders either by using liquid level indicator or by weighing the cylinders as per Article 3:2:5:4 of technical manual:Halon bottle - 04, Pilot bottle - 02 |
| 608 | SR6- Refit 02 out of 08 valve of system valves: Size- 15 mm |
| 609 | SR8-Inspect all flexible hoses in the system and replace ifrequired. |
| 610 | Carry out SR routine as follows:-SR3- Calibrate the sensors, replaced if error exceeds 0:5% of full scale: |
| 611 | SR4- Replace the battery of UPS: |
| 612 | SR5- Check for proper output of SMPS: |
| 613 | SR6- Check output of DC to DC convertor for 24 V DC: |
| 614 | SR7- Check the proper functioning of software and upgrade if any problem persists |
| 615 | Carry out Annual & SR routine as follows:-A2- Check level and condition of oil in seal package: Renew sealpackage if oil is emulsified: |
| 616 | SR1-The lubrication of mechanical seals should be checked: The lubricant might get contaminated with foreign material or get blackened due to overheating: In such cases, oil chamber should be flushed and filled with fresh oil: Before filling, heat the oil to 140 degrees C and cool it to 60 degrees C for removal of moisture in oil: |
| 617 | Carry out Annual & SR routine as follows:-A2- Check level and condition of oil in seal package: Renew seal package if oil is emulsified: |
| 618 | SR1-The lubrication of mechanical seals should be checked: The lubricant might get contaminated with foreign material or get blackened due to overheating: In such cases, oil chamber should be flushed and filled with fresh oil: Before filling, heat the oil to 140 degrees C and cool it to 60 degrees C for removal of moisture in oil: |
| 619 | ENGINEERING - PART II |
| 620 | Air leakage observed from BME air starting distributor view back pressure from air starting valves: Suspect air starting valves malfunctioning: Overhauling of the valves to be undertaken: Job involves removal, overhauling and refitting:Spares required for DR to be provided: Shipyard to quote for both the serials: Payment at actual: |
| 621 | Both main engine Copper lines for pressure gauges and pressure switches damaged/ perished: To be renewed as per sample with end adaptors:(Fuel pressure line, Jacket water pressure line, Lub oil pressure (Before filter and after filter), rocker arm oil pressure, charge air pressure A bank & B bank, Control air pressure line, sea water presssure etc) |
| 622 | Removal/ degutting of unused/ unwanted control air, fuel and lub oil lines mounted on the both main engines to be undertaken. Job involves removal of unused lines from engine to various pressure transmitters and analog parameters indication panel. |
| 623 | Manufacturing of transparent safety guard for the following panels of MCR: Material- High quality Plastic(a) RPM/ Pitch control lever(b) Both main engine safety alarm panel(c) Both main engine starting panel(d) Helicon control panel |
| 624 | Calibration of all pressure and temperature swtiches/ transmitters to be carried out: Certificate to be provided: Safety Device Checks to be undertaken as per OEM recommendation post refitment: Yard to quote for the service: |
| 625 | Both main engine lub oil and fresh water thermostat calibration to be undertaken as per OEM recommendation |
| 626 | Following valves not holding, to be overhauled- (a) 125 MM SDSL - 05 (Both Sea water pump suction vv, discharge vv & interconnecting valve |
| 627 | Scaling observed in both main engine fresh water expansion tanks.Chemical cleaning to be carried out. Testing pressure- 5 bar |
| 628 | Sub optimal performance of both main engine sea water pumps observed due to not developing sufficient pressure: Overhauling of both pumps to be carried out |
| 629 | Manufacturing of safety guards for Plummer block 6 temperature sensor of both shafts to be undertaken |
| 630 | To facilitate lub oil sampling in gear box and isolation of HP lines during safety device checks , provisioning of high pressure isolating cocks in both gear boxes pressure gauge/ transmitter lines to be undertaken. Working pressure- 30 -40 bar |
| 631 | Stbd Gear box main oil pressure and clutch oil pressure observed below operating range during prolonged exploitation: Defect to be rectified as per E&R |
| 632 | Both gear box pressure switches and temperature sensors to be calibrated: Certificate to be provided: Safety Device Checks of both gear boxes to be underaken post fitment of instrumentation: |
| 633 | Both gear box lub oil temperature slightly increasing: Lub oil cooler chemical cleaning and pressure testing to be carried out: Job involves removal, overhauling and pressure testing:Testing pressure - 06 bar |
| 634 | Both Gear box lub oil filter ultrasonic cleaning to be carried out |
| 635 | Both gear box lub oil cooler sea water valves to be overhauled: Dia - 65mm, qty - 05,Type- Gate valve (lub oil cooler S/W inlet and outlet valve, isolation valves for strainer) |
| 636 | Port GBLO pump purging valve spindle and wheel damaged/ broken: To be replaced |
| 637 | Sea water pump not developing sufficient pressureof all four DA: Overhauling of pump to be carried out: |
| 638 | Calibration of all instrumentation to be undertaken as per set values: Safety Device Checks of all 04 DA s to be carried out as per MTU trial protocols |
| 639 | Lub oil Sample cock is not avaialable in all DAs: Provision of lub oil sampling cock on all 04 DA to be undertaken: |
| 640 | Sea water leakage observed from pump discharge flange: Manufacturing and fitment of dishcarge flange to be undertaken as per existing dimension: |
| 641 | Exhaust lagging of all four DA found to be perished, same to be renewed |
| 642 | Sea water pump inlet gate valve not holding SIZE - 65 MM: To be overhauled and pressure tested: Job involves removal, overhauling and pressure testing: Testing pressure - 04 bar |
| 643 | Corrosion plugs of DA fresh water cooler and intercooler to be manufactured with end adaptors as per sample: |
| 644 | Exhaust temperature sensors of DAs malfunctioning: Calibration of all four DAs to be carried out: Renew the defective sensors: |
| 645 | DA fuel suction and discharge valve not holding:Overhauling of valves to be carried out: Renew the valve, if necessary: Qty - 08 Size - 25 mm |
| 646 | DA sea water pump suction and discharge valve not holding: Overhauling suction and discharge valves to be carried out: Renew the defective valves, if necessary: Qty - 08 Dia - 80 mm |
| 647 | Air leakage observed from air system valve for DA starting. Overhauling to be carried out. Qty- 04 nos, Dia- 25 mm |
| 648 | Sight glass not available in all four DAs: Provisioning of sight glass in all four DAs expansion tank to be carried out: Qty - 04 |
| 649 | Fuel line and return line corroded: Renewal of fuel line and return fuel line to RU tank to be carried out of all four DAs: Dia - 32 mm, mat - MS length - 50 mtr |
| 650 | All four DAs belt guard deteriorated/ corroded: Renewal of all four DAs belt guard to be undertaken as per sample: Mat - MS qty - 04 |
| 651 | All four DAs lub oil filing line cap broken: Manufacturing of Lub oil filing line cap to be carried out as per sample : Qty - 06 |
| 652 | Calibration of EDA RPM gauge (0 to 2500), fresh water temperature (0 to 150) and lub oil pressure ( 0 to 15) kg/cm2 gauges to be carried out:Qty - 06: Renew if necessary: |
| 653 | Safety device check and calibration of EDA lub oil pressure switch, F/W Temp: switch and over speed trip to be carried out: Qty 05 |
| 654 | Functional test/Calibration of solenoid valve to be undertaken: Replace defective solenoid valves (Pilot operated solenoid valve sporlan type 180S with 230 V AC coil, ASCO capacity control solenoid valve 230V with coil assembly) |
| 655 | Both AC plant compressor Differential Sea water pressure cutout to be calibrated: |
| 656 | Both AC plant compressor suction, discharge, DOP and sea water pressure gauges to be calibrated: Calibration certificate to be provided |
| 657 | Calibration/setting of thermostatic expansion valves to be carried out: |
| 658 | Scaling observed in condenser tubes: Chemical cleaning and pressure testing of both condensers to be carried out. Testing pressure- 5 bar |
| 659 | Gas leakage observed from ATU 1 TEV flange. Replacement of end flange gasket to be undertaken. Job involves retrieval of refrigerant, replacement of gasket, vacuum testing,pressure testing with Nitrogen and gas refilling |
| 660 | Manufacturing of zinc anodes to be undertaken as per sample |
| 661 | Overhauling of sea water system valves to be carried out: Qty: 12, Dia - 100 mmAC S/W Pump (P & S) suction vv- 02, Type- SDAC S/W Pump (P & S) discharge vv- 02, Type- SDNR vvAC S/W Pump pressure regulating valve-01,Type-SDNR vv |
| 662 | S/W differential pressure controller malfunctioning: Defect to be rectified: |
| 663 | AC gas system hot lagging perished at various places: AC gas system hot lagging to be renewed |
| 664 | AC gas system cold lagging perished at various places: AC gas system cold lagging to be renewed |
| 665 | Flow switch of AC showing erratic readings: Calibration of the same to be undertaken |
| 666 | Gas leakage observed from glands of condenser bypass valve & both condenser inlet valve: Overhauling to be carried out, Make-M/s Danfoss, Size- various: Job involves restoration of gas, removal, repair, refitment and setting back of system post completion: Yard to quote for the spare and OEM service seperately:(a) Liquid line isolation vv, Type- Globe vv, Size- 5/8\\"(b) Hot gas bypass line vv, Type- Globe vv, Size- 1 3/8\\"(c) Liquid line NRV vv, Size- 5/8\\"(d) Line line vv to ATU 1, Type- Globe vv, Size- 1 3/8\\"(e) Liquid line vv to ATU 2, Type- Globe vv, Size- 7/8\\"(f) Liquid line bypass vv, Type- Globe vv, Size- 1 3/8\\"(j) Suction line vv from ATU 1, Type- NRV, Size- 4 1/8\\"(k) Suction line vv from ATU 2, Type-NRV, Size- 4 1/8\\" |
| 667 | Refrigerant leakage observed from TEV end flange. Installation of isolation valve to be undertaken between TEV and ATU coil for removal and replacement of TEV |
| 668 | Solenoid vv of gas system malfunctioning: Calibration of gas system solenoid valves to be carried out: Defective solenoid valves to be replaced: Calibration certificate to be provided |
| 669 | Cold room/ cool room temperature sensors showing erratic readings: Calibration of cold room/ cool room temperature sensors to be carried out: Replace defective sensors: Calibration certificate to be provided |
| 670 | Pressure gauges of Ref showing erratic readings: Calibration of all pressure gauges to be carried out: Calibration certificate to be provided |
| 671 | Ref plant condenser sea water line strainer detiorated: Manufactured as per sample |
| 672 | Cold lagging of Both ref plant perished at various places: cold lagging to be renewed |
| 673 | Sea water system valves not holding: Overhauling of sea water system valves to be carried out: Qty 08 nos(a) Ref Condenser 1 & 2 inlet vv- Type- Gate vv, Qty- 02 nos(b) Ref Condenser 1 & 2 outlet vv- Type Gate vv,Qty- 02 nos |
| 674 | Thermostatic expansion valves malfunctioning: Calibration/setting of thermostatic expansion valves to be carried out: |
| 675 | Gas leakage observed from glands of condenser bypass valve & both condenser inlet valve: Overhauling to be carried out, Make-M/s Danfoss, Size- 5/8\\", 7/8\\" |
| 676 | Scaling observed in condenser tubes: Chemical cleaning and pressure testing of both condensers to be carried out, Testing pressure- 5 bar |
| 677 | Manufacturing of zinc anodes to be undertaken as per sample |
| 678 | S/W differential pressure controller malfunctioning: Serviceability checks to be undertaken |
| 679 | Both steering gear lub oil pressure gauges showing erratic readings: Calibration of Both steering gear lub oil pressure gauges to be carried out Qty-02: Range (0 to 15) bar |
| 680 | Clamping of both steering hydraullic system pipeline found to be broken during DI DR of lub oil leakage through rudder stock seal: Replacment/ provisioning of the clamps to be undertaken: |
| 681 | Ultrasonic cleaning of all four thrusters lub oil filter |
| 682 | All four thrusters pitch changing solenoid malfunctionig, serviciability checks to be carried out: |
| 683 | All four thrusters propeller and two main shafting propellers cleaning and preservation to be carried out during dry docking: |
| 684 | Calibration of both compressor Auto cut-in/cut-off pressure switches to be carried out: Cut-off pressure- 30 bar, cut-in pressure - 20 bar |
| 685 | Both HP air compressor low oil level sensor defective, calibration to be carried out:, Replace defective low level sensor(Shipyard to quote separately for both the serials: Payment at actual) |
| 686 | Solenoid valve of air siren malfunctioning: Serviceability checks of pneumatic air siren and solenoid valve to be carried out: |
| 687 | Air quality of BA Charging compressor found to be in alarm limit: Cleaning of air intake cooler and renewal of all filters undertaken by SS: Defect to be rectified: |
| 688 | HP hoses of BA compressor deteriorated: Replacement of all HP hoses with pressure gauge units, filters and adaptors/connectors of charging units to be carried out: |
| 689 | Carry out calibration of pressure gauge of BA compresssor:Replacement of defective gauge:(Shipyard to quote separately for both the serials: Payment at actual) Range (0 to 350) PSI |
| 690 | Electro Pnumetic valve of Ows hard to operate: Overhauling of electro pneumatic valve to be undertaken |
| 691 | Calibration of all instrumentation fitted to be undertaken Suction Guage (-1 to 5) bar Qty 02 Discharge guage (0 o 10) Qty- 04 |
| 692 | Sea water leakage observed from top cover of chamber 1: Top cover gasket to be replaced. Spare held with SS |
| 693 | Sea water overboard discharge valve hard to operate: Overhauling to be undertaken, Type- SDNR, Size- 65 mm |
| 694 | Overhauling of both AC sea water pumps to be carried out view decrease in flow rate observed. Impellers to be replaced if necessarey. |
| 695 | Overhauling of both Ref sea water pumps to be carried out view deterioration in performance |
| 696 | SV mounts observed to be cracked/ deformed, to be replacedMake- Resistoflex, Type AKCC |
| 697 | Suction and discharge valves of General service pump not holding, to be overhauled. Size- 100 mm Type- SDNR |
| 698 | Suction and discharge valves of fire main pump not holding, to be overhauledSize- 100 mm Type- SDNR |
| 699 | Suction and discharge valves of diving sea water pump not holding, to be overhauled. Size- 65 mm Type- SDNR |
| 700 | Suction and discharge valves of diving fresh water pump not holding, to be overhauled. Size- 50 mm, Type- SDNR |
| 701 | Emergency fire pump priming line with end flanges to be manfuctured as per drawing, Mat- Cu Ni |
| 702 | Performance and serviceability checks including test bed trial of 20 and 40 TPH submersible to be undertaken: Flow rate checks to be undertaken and necessary certificate to be issued |
| 703 | Flexible hoses of both DD pump found to be cracked/ deteriorated, to be renewed |
| 704 | Exhaust leakage observed from both DD pumps due to crack observed on exhaust muffler: Replacment of the same to be undertaken: |
| 705 | Peformance of hydrophore pumps observed to be sub optimal: Overhauling of pumps to be undertaken |
| 706 | System valves found leaking from glands: Overhauling of valves to be undertaken, Size- 125mm, 150 mm (Tank no.13,15,16,17,38,39), Type- QSV |
| 707 | Fire hydrant lugs and coupling found damaged: Repair of fire hydrant coupling/ lugs to be carried out: Coupling Qty- 10 ,Lugs Qty-28 |
| 708 | Calibration of auto cut off/ cut in pressure switfh fitted on hydrophore tank to be undertaken: Calibration certficate to be provided Cut in 1:7 Bar Cut out 3:2 bar |
| 709 | Calibration of Pressure relief valve fitted on hydrophore tank pneumatic system to be undertaken: Calibration certficate to be provided Range 6 bar |
| 710 | Renewal of hot lagging to be undertaken |
| 711 | Manufacturing and fitment of bilge covering net to be carried as per sample/drawing in engine room at various locations:approx area - 50 sq mtr |
| 712 | Suction and discharge valves of bilge pump not holding, to be overhauledSize- 100 mm Type SDNR |
| 713 | Renewal of all bilge suction strainer to be carried out as per sample: Qty - 10 mat - Cuni |
| 714 | Butterfly nuts of both main sea chest strainer to be renewed: Purging line and purging cock of both main sea chest to be renewed: |
| 715 | Pressure test of all 04 halon cylinders to be undertaken view pressure testing of cylinders falling due. Job involves removal of cylinders from its position, retrieval of halon, pressure test of cylinders, refilling of halon and pressurizing with Nitrogen at 42 bar. Last pressure tested in 2021,due in 2026) |
| 716 | Tank guaging system display getting switched off frequently: Suspect improper output of SMPS: Defect to be rectified: |
| 717 | UPS not holding power, to be replaced |
| 718 | Renewal of all flexible fuel hoses to be undertaken |
| 719 | Remote control assembly observed to be malfunctioning, to be replaced |
| 720 | Peformance of S/W pump observed to be sub optimal: To be replaced |
| 721 | Calibration of all instrumentation fitted to be undertaken |
| 722 | Replacement of spark plugs to be undertaken |
| 723 | Steering found to be hard to operate: Steering cable to be replaced |
| 724 | Calibration of the following test equipment to be carried out: Calibration certificate to be provided(a) Nagman LP Calibrator |
| 725 | (b) Nagman HP Calibrator |
| 726 | (c) Nagman Temperature Calibrator |
| 727 | (d) SPM T-30 |
| 728 | (e) Kittiwake Lub oil test centre |
| 729 | (f) PH meter |
| 730 | (g) Frequency Generator |
| 731 | (h) Conductivity meter |
| 732 | (j) Salinometer |
| 733 | (k) mV mA Calibrator |
| 734 | Calibration of the following relief valves to be carried out: Calibration certificate to be provided(a) HP Air Compressor (1&2) First Stage (Set Pressure - 60 PSI) |
| 735 | (b) HP Air Compressor (1&2) Second stage (Set Pressure - 300 PSI) and |
| 736 | (c) HP Air Compressor (1&2) Third stage (Set Pressure - 31 Bar) |
| 737 | (d) Emergency Air Compressor First Stage (Set Pressure -8 Bar) |
| 738 | (e) Emergency Air Compressor Second stage (Set Pressure – 32 Bar) |
| 739 | (f) AC Condenser (1&2) Relief valve (Set Pressure- ) |
| 740 | (g) Ref Condenser (1&2) Relief valve (Set Pressure- ) |
| 741 | Calibration of following Instrumentation to be Carried Out:-(a) Suction Pressure Gauge(Range -2 to +2 Bar), Qty-25 , |
| 742 | (b) Discharge Pressure Gauge(Range 0 to 5 Bar),Qty-25, |
| 743 | (c) Discharge Pressure Gauge(Range 0 to 7 Bar),Qty-15 |
| 744 | (d)Analogue thermometer(Range 0 to 7 0C), Qty-30 |
| 745 | Pressure gauge lines of pumps found to be deteriorated, to be renewed along with end fittings: Mat- Copper, Size- 15 mm, end fittings - Brass |
| 746 | Purging cocks of all pumps found to be deteriorated, to be renewed as per sample: |
| 747 | Running and stop light indication found defective in MCR auxiliary and Blower indication panel: Renewal of all LED lamps to be undertaken Defect to be rectified: |
| 748 | Pressure gauge lines, cock and valves to be renewed as per sample of various equipments: Copper tube size- 1/2\\" dia |
| 749 | End fittings for copper lines |
| 750 | Cock valves 1/2\\" dia |
| 751 | Following works to be undertaken on Bilge plates:- Renewal of rubber beading/coaming of Engine Room, Shaft Tunnel and ASP compartment bilge plates, Thickness- 5mm, Width-50mm,Running Length- 900 mtr |
| 752 | Following to be Manufactured as per sample:(a) Diesel Alternator Turning handle |
| 753 | (b) Main engine indicator cock opening handle |
| 754 | Valve wheels of various of various sizes to be manufactured view corroded as per sample: |
| 755 | Securing bracket for emergency air compressor starting handle to be provided: |
| 756 | Running and stop light indication found defective in MCR auxiliary and Blower indication panel: Renewal of all LED lamps to be undertaken Defect to be rectified: |
| 757 | POL to be provided for undertaking various routines on equipment as per details mentioned below. Shipyard to quote the serials seperately, Payment at actuals, based on the quantity mentioned in the Work Completion Certificate on not exceeding basis: (a) Oil Marine gear CEP 150 (For thrusters, CPP & G.box)- 2200 ltrs(b) Oil OMD 113 (For both main engines, HPAC, DA, Plummer block)-3000 lts(c) Oil servo system SS 68 (For Steering gear hydraullic system)- 620 ltrs(d) Oil OEP 220 (For Rudder stock) - 420 ltrs(e) Oil HLP 68 (For BME Turbocharger) - 20 ltrs(f) Oil 20W40 (For BME governor) - 20 ltrs(g) Oil Reniso SE 55 (For AC plants) - 80 ltrs (h) Oil syenthetic SAV SYN 2068- 20 ltrs(j) Oil Baour synthetic oil (For BA charging compressor)- 10 ltrs(k) Grease MMEP2 (For plummer blocks)- 40 kg(l) Nitrogen gas for PT of AC & Ref system- as per requirement |
| 758 | Machinery ventilation trunking in Engine Room and Shaft Tunnel found to be deteriorated at scattered location: Dismatling/ renewal and chemical cleaning of trunkings to be undertaken |
| 759 | Cracked/ Damaged trunking branches to be renewed: |
| 760 | Renewal of wire mesh and rubber beading of ventilation trunking in machinery spaces to be carried out: Aprrox area - 25 Sq Mtrs |
| 761 | Machinery compartment painting to be carried out as per the paint scheme: Area- 1000 Sq/Mtr: |
| 762 | Repair/ overhauling/ servicability checks of following UW valves to be undertaken prior undocking: Job involves removal, repair, pressure testing and refitment: Defective valve to be replace: Yard to quote for the spares:Fire main suction vv - 01, Dia - 100 mm |
| 763 | Bilge suction vv - 01, Dia - 100 mm |
| 764 | Emer: Fire pump sea chest vv- 01, Dia - 125 mm |
| 765 | DA suction vv - 01, Dia - 100 mm |
| 766 | AC S/W pump suction vv - 02, Dia - 125 mm |
| 767 | ME S/W pump sea chest vv – 02, Dia - 125 mm |
| 768 | ME s/w OBD vv - 02, Dia- 100 mm |
| 769 | Ref s/w OBD vv -01, Dia- 32 mm |
| 770 | Cleaning of all UW POL tanks to be undertaken: Provide ventilation obtain gas free certificate: Total no of POL tanks as follows:-(a) Fuel Tanks- Total 16, (b) Lub Oil tank- Total 07 |
| 771 | Calibrate all instrumentation |
| 772 | Suction strainer corroded/damaged. To be renewed |
| 773 | Suction and discharge valves not holding. To be overhauled, Size- 150mm, Type - SDNR |
| 774 | Low cooling effect observed. Suspect scaling in condenser tubes. Condenser cleaning and pressure test to be undertaken |
| 775 | S/W system cocks not holding. To be renewed, Size- 25 mm |
| 776 | Both AC condenser tubes found to be choked. Chemical cleaning and pressure testing (at 1.5 times of working pressure )of both condensers to be carried out. All end cover gaskets and o rings to be replaced |
| 777 | Scaling observed in heat exchangers (Fresh water, lub oil and inter cooler). Chemical cleaning and pressure testing (at 1.5 times of working pressure ) to be undertaken. All end cover gaskets and o rings to be replaced |
| 778 | SR1- Internally clean the 25% of exhaust silencer/fittings. |
| 779 | Tube stacks / tube sheet of FW oil cooler persihed. Tube stacks to be manufactured as per sample and cooler to be pressure tested at 1.5 times working pressure |
| 780 | Dismantle and overhaul entire hydraulic control system. |
| 781 | Excessive, pitting and corrosion observed on the operating cylinders of CPP cylinder of both shafts. Cleaning and metal build up of the same to be undertaken post dismounting. |
| 782 | Air leakage observed from main engine air starting station, same to be overhauled. Yard to quote for spares. |
| 783 | Moisture ingression in starting air system observed in starting air bottles causing malfunctioning of starting air valves. Defect to be rectified. |
| 784 | Cleaning and polishing of both propeller blades and preservation to be carried out during dry docking. |
| 785 | Excessive fuel leak off from injectors observed in Port main engine. Suspect improper loading of Port Main Engine, Defect to be rectified. |
| 786 | Overhaul of Both main engine sea water differential valve, interconnecting valve. Size 125 mm Globe vv. |
| 787 | Leakage observed from bodies of fuel and lub oil filters of both main engines. Filter bodies to be renewed. ( to be sourced from OEM ) |
| 788 | Redundant control air, fuel and lub oil lines mounted on the both main engines to be removed. Job entails degutting of existing lines after removal of fuel and lub oil lines. Engine bodies to be prepared and painted as per colour scheme |
| 789 | Control panels of all 4 DAs to be overhauled. DA no. 1 cranking automatically after switching off starting/PLC panel. Defect to be rectified. |
| 790 | (a) Repair/ serviceability checks of Over Voltage Protection Unit (OVPU), Reverse Power Relay and Over Speed Trip. |
| 791 | REF plant condenser S/W line to be renewed. Length 50mtr. Material cu ni. Dia 40mm. |
| 792 | PRT and CSL in house trials reports revealed oil leakage from thrusters seal. Meeting with OEM brought out replacement of seal on all four Thrusters for the defect rectification. |
| 793 | CPP blade routines, Hub overhauling and blade foot inspection & skimming. |
| 794 | During overhauling by OEM, scoring marks, pitting & shaft edge deformation observed on port steering pump shaft. Replacement of pump shaft required. |
| 795 | Rudder angle indicator malfunctioning, suspect rudder angle amplifier PCB defective , need to be replaced and system to be proven. |
| 796 | Check and Replace the servo piston rod and Gaco seal, retaining ring and circlip of both Gear boxes |
| 797 | ELECTRICAL - PART I |
| 798 | SR1 - Remove and examine sea-water side of Alternator air cooler (where fitted) for corrosion, erosion and fouling. Clean tube plate and tubes with water jet (BR 3000 art. 1801 refers). Carry out chemical cleaning if necessary. Pressure test on completion. |
| 799 | SR5 - Check AVR for serviceability. Carry out calibration as necessary. In case of any tuning/ calibration undertaken on AVR, the voltage control test and paralleling trials to be undertaken. |
| 800 | SR9 - Check securing arrangement of power and control cables to bus bar/ AVR. All loose screws to be tightened. Defective screws to be replaced. |
| 801 | SR10 - Replace the following (where applicable) :- (a) Thermo-couple(b) Electrical temperature indicator(c) Tacho-meter transmitter(d) Ball and roller bearing of pump motor(e) Rotating Rectifier assembly |
| 802 | SR11 - Carry out SPM checks, phase balancing, insulation measurement. Overhaul generator and replace bearings, if required and carry out load trials and Record results in Log Book. Note:- Before changing the lubricant of bearings, wash out bearing assembly. Washing the bearing assembly is to be carried as per Technical Instructions of the Alternator. |
| 803 | SR2 - Check the function of speed control relay device as per the service Manual. Adjust if required. |
| 804 | SR5 - Remove and examine sea water side of generator air cooler (where fitted) for corrosion, erosion and fouling. Clean tube plate and tubes with water jet (INBR 300 art. 1801 refers). Carry out chemical cleaning if necessary. Pressure test on completion. |
| 805 | SR6 - Replace the following (where applicable) :- (a) Ignition coil (b) spark plug(c) Thermo-couple(d) Electrical temperature indicator(e) Tacho-meter transmitter(f) Ball and roller bearing of pump motor(g) Rotating Rectifier assembly. |
| 806 | SR1 - Remove and examine sea-water side of Alternator air cooler (where fitted) for corrosion, erosion and fouling. Clean tube plate and tubes with water jet (BR 3000 art. 1801 refers). Carry out chemical cleaning if necessary. Pressure test on completion. |
| 807 | SR5 - Check AVR for serviceability. Carry out calibration as necessary. In case of any tuning/ calibration undertaken on AVR, the voltage control test and paralleling trials to be undertaken. |
| 808 | SR9 - Check securing arrangement of power and control cables to bus bar/ AVR. All loose screws to be tightened. Defective screws to be replaced. |
| 809 | SR10 - Replace the following (where applicable) :-(a) Thermo-couple(b) Electrical temperature indicator.(c) Tacho-meter transmitter.(d) Ball and roller bearing of pump motor.(e) Rotating Rectifier assembly. |
| 810 | SR11 - Carry out SPM checks, phase balancing, insulation measurement. Overhaul generator and replace bearings, if required and carry out load trials and Record results in Log Book. Note:- Before changing the lubricant of bearings, wash out bearing assembly. Washing the bearing assembly is to be carried as per Technical Instructions of the Alternator. |
| 811 | SR5 - Carry out complete overhauling of the rectifier. |
| 812 | SR1 - Calibrate 50% of panel instruments/ meters. |
| 813 | SR3 - Carry out in-situ serviceability checks of breakers and raise specific defect to dockyard for repairs . Carry out serviceability checks of GSK relay and other protection circuits ; raise specific defects to dockyard, (where applicable). |
| 814 | SR5 - Carry out following routines on Switchboard and busbars:- (a) Inspect lugs/ connectors/CT/PT and other components and undertake repair deterioration / damageof MSB cables/ wiring as necessary. (b) Repair/ replace busbars insulators if necessary. (c ) Clean and decarbonised the busbars. (d) carryout fuctional checks of MSB and paralleling trials with all combinations of generator supply |
| 815 | SR1 - Calibrate 50% of panel instruments/ meters. |
| 816 | SR3 - Carry out in-situ serviceability checks of breakers and raise specific defect to dockyard for repairs . Carry out serviceability checks of GSK relay and other protection circuits ; raise specific defects to dockyard. (where applicable) |
| 817 | SR5 - Carry out following routines on Switchboard and busbars:- (a) Inspect lugs/ connectors/CT/PT and other components and undertake repair deterioration / damageof MSB cables/ wiring as necessary(b) Repair/ replace busbars insulators if necessary(c ) Clean and decarbonised the busbars (d) carryout fuctional checks of MSB and paralleling trials with all combinations of generator supply |
| 818 | SR1 - Overhaul Navigational lights, control panels, check all the switches and replace defective switches. |
| 819 | SR2 - Check the supply cables of signaling projectors, if perished Renew/Rewire. |
| 820 | SR3 - Check bell circuits and check all the lights for correct brilliancy. |
| 821 | SR1 - Overhaul the equipment completely and do as mentioned below:-(a) Change the element if defective(b) Renew the internal wiring if perished(c) Check the rotary switches, change with new one if required(d) Calibrate temperature sensors and temperature gauges if fitted(e) Check temperature cut-out of water heaters for satisfactory operation and adjust as required. |
| 822 | SR1 - Overhaul the motor & starters. Renew bearings subject to Q.C checks (SS to forward SPM readings). |
| 823 | SR2 - Calibrate Over-load mechanism of the starter. |
| 824 | SR6 - Calibrate the Over-load mechanism of the starter. |
| 825 | SR2 - Carry out the alignment of the pump driven unit with the motor if necessary. |
| 826 | SR3 - Carry out SPM checks. Lubricate/ replace bearings as necessary (Raise specific defects to dockyard). |
| 827 | SR1 - Carry out complete overhauling of the equipment. The overhaul procedure includes dismantling EPH whistle completely, removal and cleaning of all parts separately, replacement of damage components, inspection of mounting position and reassemble and putting back the EPH Whistle in operation.(Refer Operation and Maintenance manual for Marine Electric Piston Horn Whistle Model RKEW-200) Chapter-4 Para 2and 3. |
| 828 | SR2 - Do the dismantling of Electric motor and carry out maintenance routines as per para 4 Chapter 4. (Refer Operation and Maintenance manual for Marine Electric Piston Horn Whistle Model RKEW-200).Note: Follow the reverse procedure of para 4 when assembling the electric motor after repair/maintenance. |
| 829 | SR1 - Lubricate/ replace bearings as necessary (SS to Carry out SPM checks and forward SPM checks report to QC). |
| 830 | SR2 - Carry out calibration of Overload Relay (OLR)/ Thermal Protection (TP) of starter. |
| 831 | A2 - Dismantle the heating elements and clean or descale them thoroughly. Check switch, fuses, temperature limiter and reassemble them as per drawing. |
| 832 | SR1 - Calibrate all Instrumentation. |
| 833 | SR2 - Overhaul 25% system valves. |
| 834 | SR1 - Overhaul 25% system valves. |
| 835 | SR2 - Calibrate all Instrumentation. |
| 836 | SR1 - Lubricate/ replace bearings as necessary (SS to Carry out SPM checks and forward SPM checks report to QC). |
| 837 | SR2 - Carry out calibration of Overload Relay (OLR)/ Thermal Protection (TP) of starter. |
| 838 | SR1 - Overhaul the motor & starters. Renew bearings subject to Q.C checks (SS to forward SPM readings). |
| 839 | SR2 - Calibrate Over-load mechanism of the starter. |
| 840 | SR2 - Calibrate the over-load mechanism of starter. |
| 841 | SR2 - Calibrate the over-load mechanism of starter. |
| 842 | SR1 - Overhaul the motor & starters. Renew bearings subject to Q.C checks (SS to forward SPM readings). |
| 843 | SR2 - Calibrate Over-load mechanism of the starter. |
| 844 | SR1 - Overhaul the motor & starters. Renew bearings subject to Q.C checks (SS to forward SPM readings). |
| 845 | SR2 - Calibrate Over-load mechanism of the starter. |
| 846 | SR1 - Overhaul the motor & starters. Renew bearings subject to Q.C checks (SS to forward SPM readings). |
| 847 | SR2 - Calibrate Over-load mechanism of the starter. |
| 848 | SR1 - Overhaul the motor & starters. Renew bearings subject to Q.C checks (SS to forward SPM readings). |
| 849 | SR2 - Calibrate Over-load mechanism of the starter. |
| 850 | SR1 - Overhaul the motor & starters. Renew bearings subject to Q.C checks (SS to forward SPM readings). |
| 851 | SR2 - Calibrate Over-load mechanism of the starter. |
| 852 | SR1 - Overhaul the motor & starters. Renew bearings subject to Q.C checks (SS to forward SPM readings). |
| 853 | SR2 - Calibrate Over-load mechanism of the starter. |
| 854 | SR1 - Overhaul the motor & starters. Renew bearings subject to Q.C checks (SS to forward SPM readings). |
| 855 | SR2 - Calibrate Over-load mechanism of the starter. |
| 856 | SR1 - Overhaul the motor & starters. Renew bearings subject to Q.C checks (SS to forward SPM readings). |
| 857 | SR2 - Calibrate Over-load mechanism of the starter. |
| 858 | SR2 - Calibrate Over-load mechanism of the starter. |
| 859 | SR1 - Overhaul the motor & starters. Renew bearings subject to Q.C checks (SS to forward SPM readings). |
| 860 | SR1 - Overhaul the motor & starters. Renew bearings subject to Q.C checks (SS to forward SPM readings). |
| 861 | SR2 - Calibrate Over-load mechanism of the starter. |
| 862 | SR1 - Overhaul the motor & starters. Renew bearings subject to Q.C checks (SS to forward SPM readings). |
| 863 | SR2 - Calibrate Over-load mechanism of the starter. |
| 864 | SR1 - Overhaul the motor & starters. Renew bearings subject to Q.C checks (SS to forward SPM readings). |
| 865 | SR2 - Calibrate Over-load mechanism of the starter. |
| 866 | SR1 - Overhaul the motor & starters. Renew bearings subject to Q.C checks (SS to forward SPM readings). |
| 867 | SR2 - Calibrate Over-load mechanism of the starter. |
| 868 | SR1 - Overhaul the motor & starters. Renew bearings subject to Q.C checks (SS to forward SPM readings). |
| 869 | SR2 - Calibrate Over-load mechanism of the starter. |
| 870 | SR2 - Carry out the alignment of the pump driven unit with the motor if necessary. |
| 871 | SR3 - Carry out SPM checks. Lubricate/ replace bearings as necessary (Raise specific defects to dockyard). |
| 872 | SR6 - Calibrate the Over-load mechanism of the starter. |
| 873 | SR2 - Carry out the alignment of the pump driven unit with the motor if necessary. |
| 874 | SR3 - Carry out SPM checks. Lubricate/ replace bearings as necessary (Raise specific defects to dockyard). |
| 875 | SR6 - Calibrate the Over-load mechanism of the starter. |
| 876 | SR2 - Calibrate the Over-load mechanism of the starter. |
| 877 | SR3 - Carry out the alignment of the pump driven unit with the motor if necessary. |
| 878 | SR6 - Carry out SPM checks. Lubricate/ replace bearings as necessary (Raise specific defects to dockyard). |
| 879 | SR2 - Carry out the alignment of the pump driven unit with the motor if necessary. |
| 880 | SR3 - Carry out SPM checks. Lubricate/ replace bearings as necessary (Raise specific defects to dockyard). |
| 881 | SR6 - Calibrate the Over-load mechanism of the starter. |
| 882 | SR3 - Carry out SPM checks. Lubricate/ replace bearings as necessary (Raise specific defects to dockyard). |
| 883 | SR2 - Carry out the alignment of the pump driven unit with the motor if necessary. |
| 884 | SR6 - Calibrate the Over-load mechanism of the starter. |
| 885 | SR3 - Carry out the alignment of the pump driven unit with the motor if necessary. |
| 886 | SR2 - Carry out SPM checks. Lubricate/ replace bearings as necessary (Raise specific defects to dockyard). |
| 887 | SR6 - Calibrate the Over-load mechanism of the starter. |
| 888 | SR6 - Calibrate the Over-load mechanism of the starter. |
| 889 | SR2 - Carry out the alignment of the pump driven unit with the motor if necessary. |
| 890 | SR3 - Carry out SPM checks. Lubricate/ replace bearings as necessary (Raise specific defects to dockyard). |
| 891 | SR1 - Lubricate/ replace bearings as necessary (SS to Carry out SPM checks and forward SPM checks report to QC). |
| 892 | SR2 - Carry out calibration of Overload Relay (OLR)/ Thermal Protection (TP) of starter. |
| 893 | A1 - Calibrate the over-load mechanism of the starter. |
| 894 | SR1 - Lubricate/ replace bearings as necessary (SS to Carry out SPM checks and forward SPM checks report to QC). |
| 895 | SR2 - Carry out calibration of Overload Relay (OLR)/ Thermal Protection (TP) of starter. |
| 896 | A1 - Calibrate the over-load mechanism of the starter. |
| 897 | SR1 - Lubricate/ replace bearings as necessary (SS to Carry out SPM checks and forward SPM checks report to QC). |
| 898 | SR2 - Carry out calibration of Overload Relay (OLR)/ Thermal Protection (TP) of starter. |
| 899 | A1 - Calibrate the over-load mechanism of the starter. |
| 900 | SR1 - Lubricate/ replace bearings as necessary (SS to Carry out SPM checks and forward SPM checks report to QC). |
| 901 | SR2 - Carry out calibration of Overload Relay (OLR)/ Thermal Protection (TP) of starter. |
| 902 | A1 - Calibrate the over-load mechanism of the starter. |
| 903 | A2 - Remove and carry out overhauling (and replacement of bearing based on QC) of the motor fitted in trunkings for Boiler room / Engine room / DA compartment and Galley exhaust. |
| 904 | A2 - Remove and carry out overhauling (and replacement of bearing based on QC) of the motor fitted in trunkings for Boiler room / Engine room / DA compartment and Galley exhaust. |
| 905 | SR2 - Calibrate Over-load mechanism of the starter. |
| 906 | SR1 - Overhaul the motor & starters. Renew bearings subject to Q.C checks (SS to forward SPM readings). |
| 907 | SR1 - Overhaul the motor & starters. Renew bearings subject to Q.C checks (SS to forward SPM readings). |
| 908 | SR2 - Calibrate Over-load mechanism of the starter. |
| 909 | SR2 - Calibrate Over-load mechanism of the starter. |
| 910 | SR1 - Overhaul the motor & starters. Renew bearings subject to Q.C checks (SS to forward SPM readings). |
| 911 | SR2 - Carry out the alignment of the pump driven unit with the motor if necessary. |
| 912 | SR3 - Carry out SPM checks. Lubricate/ replace bearings as necessary (Raise specific defects to dockyard). |
| 913 | SR6 - Calibrate the Over-load mechanism of the starter. |
| 914 | SR1 - Overhaul the motor & starters. Renew bearings subject to Q.C checks (SS to forward SPM readings). |
| 915 | SR2 - Calibrate Over-load mechanism of the starter. |
| 916 | SR1 - Open the unit and check the wiring/ contacts for wear/ deterioration. Renewal/ replace any defective componant, if necessorry |
| 917 | SR2 - Check manualy movable part of the contactors |
| 918 | SR1 - Check sensor for contamination due to exhaust gases, wash it with fresh water and mild soap solution as necessary. |
| 919 | SR2 - Check the shock/vibration mounts, renew if necessary. |
| 920 | SR 3 - Carry out parameter checks of the radar. |
| 921 | SR 4 - Clean & apply RF paint on the antenna. |
| 922 | SR 5 - Inspect the shock mounts and check that the fastening units are properly tightened. Re-coat with Necol Lacquer. |
| 923 | SR 6 - Change the oil in combined antenna pedestal. Check the system for proper operation. |
| 924 | SR 7 - Carry out VSWR, Sensitivity and Power output checks. |
| 925 | SR 10 - Measure characteristic impedance of the antenna feeder. |
| 926 | SR 11 - Carry out complete overhauling of the equipment and test for optimum performance. |
| 927 | 4M 4 - Check power output of the system |
| 928 | 4M 5 - Check the range calibration of the display. |
| 929 | 6M 3 - Carry out internal inspection of all devices. Check the fan for working (with unit switched ON). Remove dust build up within the unit and around the air filter. Wash/ replace air filter as necessary. |
| 930 | 6M 6 - Remove the pedestal cover of antenna group and carry out the following:-(If applicable) (i) Internal cleaning of casing, remove dust, dirt and scales if any(ii) Proper connection of power cable(iii) Replace mechanical, electrical and electronic components, if required(iv) Check the antenna position indicator components replace if required(v) Check integrity and tension of driving belt, replace if required. |
| 931 | 6M 1 - Check antenna for mechanical damage/ water penetration. |
| 932 | 6M 2 - Check the antenna motor brushes for excessive wear and lubricate the drive shaft and gear using the grease nipple. |
| 933 | 6M 7 - Check the drive motor brush as it has an expected life of 2000 Hrs. Replace it when half of overall length has worn out. |
| 934 | 6M 4 - Check the currents in transmitter and receiver ensure they are in prescribed range. |
| 935 | 6M 5 - Check for the following of antenna group:- (If applicable) (i) No part of the antenna front has been painted (ii) Condition of scanner base housing (iii) Condition of ball bearing (iv) Condition of grease on the fixing bolts of cover appply if necessery. |
| 936 | SR1 - (a)Carry out the printer and speed control checks as per INBR 2651(2), Part II, Para 2.3.10. (As Applicable)(b)Carry out checks of Printer as per INBR 4826(iii) Chapter 3, Para 3.8 (For Ver 3). (As Applicable) |
| 937 | SR4 - (a)Service the Echo Sounder PCBs in accordance with the INBR 2651(2), part II, Para 3.2. (As Applicable) (b)Service the Echo Sounder modules in accordance with the INBR 4826(iii), Chapter 5 (For Ver3).(As Applicable) |
| 938 | SR2 - Examine the transducer and casing. Preserve the transducer surface during dry-docking. Carryout visiual examination of the transducer cables, checks continuity and insulation. Project defects to Dockyard for necessory repairs. |
| 939 | SR3 - Carry out visual examination of PCBs Viz. PC1 to PC11 / Modules in accordance with Annual Maintenance Schedule of INBR 2651(2), Part II, Para 2.4.1 (As Applicable).Note: - (i)INBR 4826(X) Part II chapter 2, Para 2.4 refers for Ver 3.1(ii)INBR 4826(iii) Chapter 2, Para 2.4 refers for Ver 3 |
| 940 | SR1 - (a) Carry out the printer and speed control checks as per INBR 2651(2), Part II, Para 2.3.10. (As Applicable)(b) Carry out checks of Printer as per INBR 4826(iii) Chapter 3, Para 3.8 (For Ver 3). (As Applicable) |
| 941 | SR3 - Carry out visual examination of PCBs Viz. PC1 to PC11 / Modules in accordance with Annual Maintenance Schedule of INBR 2651(2), Part II, Para 2.4.1 (As Applicable).Note: - (i)INBR 4826(X) Part II chapter 2, Para 2.4 refers for Ver 3.1(ii)INBR 4826(iii) Chapter 2, Para 2.4 refers for Ver 3 |
| 942 | SR4 - (a) Service the Echo Sounder PCBs in accordance with the INBR 2651(2), part II, Para 3.2. (As Applicable)(b)Service the Echo Sounder modules in accordance with the INBR 4826(iii), Chapter 5 (For Ver3).(As Applicable) |
| 943 | SR1 - (a) Carry out the No load test in accordance with the Maintenance Manual 2650(2), chapter 5, para 5.1.1. (As Applicable) |
| 944 | SR1 - (b) Overhaul and Reconditioning in accordance with INBR 4835(v) (For Ver3). (AsApplicable). |
| 945 | SR2 - (c)Carry out Speed and Distance run for the Master Unit. |
| 946 | SR2 - Carry out serviceability checks of UPS, PCBs in interface unit and processor. Raise specific defect to yard for repairs. |
| 947 | SR1 - Carry out functional Performance check of the system. |
| 948 | SR2 - Carry out serviceability checks of UPS and system consoles. |
| 949 | SR1 - Check the transducers for vegetation growth and damage. The transducers emitter surface must be cleaned using a soft brush and clear fresh water. Do not use steel brushes or scrapers. Damaged transducers must be replaced. |
| 950 | SR2 - Renew the antifouling coating. |
| 951 | SR1 - Check shock aborber, replace if defective |
| 952 | SR1 - Carry out serviceability checks of batteries. |
| 953 | SR2 - Carry out capacity test of batteries. |
| 954 | SR3 - Carry out serviceability checksm of invertor as per technical mannual |
| 955 | SR1 - Inspect shock/ vibration mountings for damage/ detriotion. Renew if necessory. Apply necol lacquer on shock mounts |
| 956 | SR2 - Carry out calibration and perform self-checks. |
| 957 | SR1 - Carry out the performance and parameters checks as per section 4.2 & 4.3 of maintenance manual. |
| 958 | SR1 - Inspect the shock mount for damage/ detrioration, renew if necessary |
| 959 | SR2 - Carry out callibration of recorder unit and perform self check. |
| 960 | SR1 - Carry out Overhauling of antenna system. |
| 961 | SR1 - Carry out servicebility checks of all RF modem cards, serial cards, power supply cards and RAID card in server and SADL.(Routine of RAID card not applicable to Link II MOD I Ver 2.4) |
| 962 | SR2 - Inspect the shock mounts for damage/deterioration, renew if required. |
| 963 | SR1 - Inpect shock/ vibration mountings for damage/ detoriation, renew if required |
| 964 | SR2 - Inspect wiring componants for damage, internal cleaning |
| 965 | SR1 - Carry out serviceability check of all units and overall check-up of system including ACOS, PCBs, Manual call points, detectors & Hooters (where applicable). Project specific defect to dockyard and undertake repair/ replacement of defective part. |
| 966 | SR 6 - Calibrate the Over-load mechanism of the starter. |
| 967 | SR 3 - Carry out SPM checks. Lubricate/ replace bearings as necessary. |
| 968 | SR 2 - Carry out the alignment of the pump driven unit with the motor if necessary. |
| 969 | SR6 - Carry out calibration of Overload Relay (OLR)/ Thermal Protection (TP) of starter. |
| 970 | SR3 - Lubricate/ replace bearings as necessary (SS to Carry out SPM checks and forward SPM checks report to QC). |
| 971 | SR1 - Renew supporting liquid, distilled water and carry out following checks:- (i) Switch ON gyro compass and check its performance. (ii) Check follow-up system with gyro compass. (iii) Check sensitivity of follow-up system, it should not be less than70 degrees/ second. |
| 972 | SR2 - Overhaul motors and renew bearings. |
| 973 | SR 3 - Carry out SPM checks. Lubricate/ replace bearings as necessary. |
| 974 | SR 6 - Calibrate the Over-load mechanism of the starter. |
| 975 | SR 2 - Carry out the alignment of the pump driven unit with the motor if necessary. |
| 976 | SR 6 - Calibrate the Over-load mechanism of the starter. |
| 977 | SR 3 - Carry out SPM checks. Lubricate/ replace bearings as necessary. |
| 978 | SR 2 - Carry out the alignment of the pump driven unit with the motor if necessary. |
| 979 | ELECTRICAL - PART II |
| 980 | Preservation and securing of all electrical equipment/ DBs/ JBs to be undertaken prior to commencement of refit till completion of habitability work onboard. |
| 981 | Repair of existing fitted commercial UPS view low backup including replacement of batteries (1KVA- 25 Qty) |
| 982 | Overlay of both radars with WECDIS is prone to intermittent, the same need to be proven. RIB (Radar Interface Box) to be repair if required. |
| 983 | Radar sensitivity renders low over the period of exploitation, Rx Assy to be checked for optimum performance, repair if required (Qty-02) |
| 984 | Buffer unit of Both DGPS malfunctioning. Replacement of same to be carried out. System to be proved post DI/DR. |
| 985 | All nav data of ship's GPS 2 observed to be lost intermittently view display port of GPS JB defective. Need to be rectified. |
| 986 | Software glitch observed in the system resulting deletion of complete system configuration frequently. Defect rectification to be carried out for the same. |
| 987 | User Interface Software and communication with trasducer of system stop working frequenlty. RA for DI/DR |
| 988 | DR required on system view showing eratic depth value on 210 hz channel. |
| 989 | 5KVA UPS of UWT malfunctioniong intermitantly due to aging. UPS and batteries to be replaced (Qty-06). |
| 990 | Two 3KVA UPS of DP systeme not working due to aging. Need to be replaced. |
| 991 | System position accuracy observed to be low view HDOP and VDOP showing approx 2 mtrs, also the system declared obsolete by OEM. Need to be upgraded to the latest version. |
| 992 | Wind Sensors of DP system malfunctioning due to aging. System to be raplaced with latest version. |
| 993 | (b) Defective Microphones (Mic) of Main broadcast, need to be replaced. |
| 994 | (d) Repair of 8 Watt speakers and cabling (4 core screen cable - approx 100 Mtrs) at following places to be carried out in view of defective: -(i) Quarter deck (port & stbd)(ii) Foxle(iii) Catwalk (port & stbd)(iv) Bridge Top(v) EDA(vi) SDC Container (Outside) |
| 995 | (e) Repair/Replacement of Mic Connection Box at following Locations to be carried out in view of defective:-(i) Foxle(ii) Quarter Deck (port & stbd)(iii) Bridge Top |
| 996 | (a) Sub-optimal performance and repeated failures of amplifiers of Machinery, MCR-BRIDGE, Diving & Conning intercom. Replacement of amplifiers be undertaken. |
| 997 | (b) Intercom wiring of Foxle, Bridge Wing, Quarter Deck (Port & Stbd), Boat Deck (Port & Stbd) and Bridge top for MCB & Speaker deteriorated/ damaged, to be replaced Qty- 500 mtrs (4 core screen cable). |
| 998 | (c) Replacement of MCB at following Locations to be carried out in view of malfuctioning:-(i) Bridge Top (port & stbd)(ii) Bridge Wing (port & stbd)(iii) Boat Deck (port & stbd)(iv) Foxle(v) Quarter deck (port & stbd)(vi) SDS Container (outside) |
| 999 | (a) Repair of telephone exchange system in view of frequently failure, suspected defect on following cards :-(i) Controller card (ii) Tone generation card(iii) Power supply unit |
| 1000 | (b) Telephone wiring of deck crane & catwalk (port & stbd) damaged and deteriorated, needs to be replaced. |
| 1001 | (c) Replacement of Junction Boxes of Telephone exchange at following Locations to be undertaken in view of deteriorated:-(i) Port Catwalk(ii) DCHQ Lobby(iii) DDC(iv) Dining Hall Lobby(v) Captains Looby(vi) Officers Lobby(vii) Stbd Catwalk |
| 1002 | Repair of following module of SDR NC to be carried out in view of main MCB tripping frequently:-(i) Power Distribution Unit(ii) RF & Baseband Unit(iii) V/UHF PA 50W (Qty-02)(iv) HF PA 100W |
| 1003 | (a) Augmentation of additional storage capacity of existing CCTV NAS Storage system for min 30 days backup. |
| 1004 | (b) Laying of VGA cable from SDC and SDS to bridge through cable tray for live streaming of dive feed (Qty-120 Mtrs) |
| 1005 | (c) Replacement of D-Link switch in MCR in view of malfunctioning. |
| 1006 | (d) Replacement of 05 Static IP Cameras (waterproof) & 02 PTZ cameras (waterproof) to be undertaken in view of defective. |
| 1007 | (e) Replacement of client PC & server pc in MCR & Bridge need to be undertaken view malfunctioning. |
| 1008 | (f) CCTV Camera wiring (cat-6) of following locations damaged and deteriorated, needs to be replaced, old cables to be removed:-(i) Foxle(ii) Bosun Store(iii) Catwalk (port & stbd)(iv) MainMast PTZ(v) Captains' Lobby(vi) Officers' Lobby(vii) Galley(viii) DCHQ(ix) FWD Thruster(x) Canteen Lobby(xi) Engine Room (Qty-04)(xii) Shaft Tunnel (Qty-02)(xiii) Sat Control Room(xiv) EDA(xv) Deck Crane PTZ(xvi) Engine Room PTZ(xvii) ASP(xviii) Aft Thruster(xix) Boat Deck (port & stbd)(xx) magazine(xxi) Armoury(xxii) Moonpool PTZ |
| 1009 | Calibration checks (Repairing if required) of following NBCD equipment view calibration falling due in E-AMP and calibration certificate to be provided:: -(i) Radiation survey meter- 03 Qty(ii) Decontamination kit- 02 Qty(iii) Gamma zone monitor- 01 Qty(iv) Thermal imagine camera- 02 Qty(v) Field telephone- 04 Qty |
| 1010 | (a) Replace defective lamps. |
| 1011 | (b) Existing wiring of following galley equipment perished/ deteriorated and need to be replaced: -(i) Range four hot plate- 01 qty(ii) Range two hot plate- 01 qty(iii) Bain Marie- 01 qty(iv) Deep fat frier- 01 qty |
| 1012 | (c) Implementation of shock mount and new earthing straps on following galley equipmenmts:-(i) Range four hot plate- 01 qty(ii) Range two hot plate- 01 qty(iii) Bain Marie- 01 qty(iv) Deep fat frier- 01 qty |
| 1013 | Manufacturing and fitment of cable tray (Qty - 300 Mtrs) view deteriorated and securing of cables with Rubber shield metallic strip throughout the ship. Removal of old cables from machinary Compartments |
| 1014 | Replacement of battery charger, navigational panel, compass, horn and rewiring of Boat cables including proper securing. |
| 1015 | Sealing of cable glands at various places post completion of cabling work. |
| 1016 | Replacement of window wiper in view of tripping frequently and showing sub-optimal performance. |
| 1017 | Repair of led lights, replace defective LED drivers (50 Qty) view defective. |
| 1018 | Calibration checks of 01 voltmeter and 01 ammeter in view of calibration falling due in E-AMP and provide calibration certificate. |
| 1019 | Replace of heating elements and thermostat of both calorifiers view malfunctining, proper heating and proper cut in cut out off not working. |
| 1020 | (b) Repair of shore supply junction box view deteriorated. Defective switches (02), fuse bases(06) & lugs (12) to be replaced. |
| 1021 | (a)Replacement of 12 NBCD switch sockets with weather proof IP66/ 67 compliant & recabeling of NBCD Sockets view deteriorated and low insulation value. |
| 1022 | (b) Implementation of Protective cover on Sockets on Upper decks to provide additional protection to the switch sockets |
| 1023 | Replacement of 05 SPTs, 05 audio visual alarm, 05 hooter view defective. |
| 1024 | (a) Repairs of soft starters, Control panel , VFD of both boat davit motors view malfunctioning. |
| 1025 | (b) Replacement of 10 limit switches view damaged. |
| 1026 | (a) Implementation of LED Flood lights for following machinary space as part of change management policy:-(i) Main Engine Room(ii) Deep Diving Chamber Compartment(DDC)(iii) Shaft Tunnel(iv) ASP & Aft Thruster(v) Fwd Thruster |
| 1027 | Implementaion of metallic polycarbonate shields covers to be fitted within pipelines flanges in vicinity of electrical equipment:-(i) MCC1,2 & 3.(ii) AC control panel 1& 2.(iii) Balast Pump Control Panel (P) (S).(iv) Ref Control Panel.Authority NHQ/DNO letter Op/Safety/5106/5B dated 31 Dec 2019 |
| 1028 | DA 1 and 4 cabels showing low insulation below 2M ohm (required above 40 M ohm). Old cables to be replaced with new cables. |
| 1029 | (a) Ebonite insulating plates are to be placed over live terminals inside distribution boxes |
| 1030 | (b) Tally indicating details of equipment fed from each switch/ MCB to be placed for easy identification |
| 1031 | (a) Replacement of weather proof IP66/ 67 compliant switch sockets view low insulation |
| 1032 | (b) Recabling required for illumination sockets view damaged (220V). |
| 1033 | (a) Replacement of all navigational Lights view base and light defective. |
| 1034 | (b) Recabling required for navigational lights view damaged and perished (220V). |
| 1035 | (a) Repair of Deck crane motor and control Panel as Power cointinuosly Tripping. |
| 1036 | (b) Replacement of limit switch and carbon brushes view defective. |
| 1037 | (a) Repair of clutch in/out indication of mooring remote panel in view of not working.(b) Replacement of DE (6313ZZ C3) and NDE (6312ZZ C3) bearings of all 04 mooring motors in view of SPM observed in yellow zone. (440V, 60Hz, 3ph, 46 KW) |
| 1038 | (a) Feed from LWTW not processed at DP system. Suspect PLC malfunctioning.(b) Replacement required of the followings due to deterioration: -(i) Pneumatic line including valve assembly(ii) Solenoid valve assembly for boom in/out(iii) Emergency stop push button including contactor |
| 1039 | (a) Repair of pelorus repeaters of Gyro in view of pivot damaged and key deteriorated. Qty-04 |
| 1040 | (b) Locking mechanism of Gyro sphere to be changed in view damaged. |
| 1041 | (c) Defective indication lamps of control units to be replaced. |
| 1042 | (a) Calibration of the system to be carried out and prove the system for optimum performance and provide calibration certificate. |
| 1043 | (a) Repair of following in view of defective:-(i) 10 Manual call points(ii) 10 smoke/heat detectors (iii) 05 Hooters. |
| 1044 | (a) Repair of following in view of malfunctioning :-(i) 05 float sensors (ii) Software of MCP |
| 1045 | (a) Carry out swing check and calibrate the compass. |
| 1046 | (a) Calibration of RCI-1550 display unit to be carried out in view of showing erratic reading. |
| 1047 | (b) Calibrate the both tensiometer sensor for pay out/ pay in and load on cable. Repair encoder PCB and sensor. |
| 1048 | (a) Defective contactors of starter to be replaced(i) 3RT1975-6A (Qty-02)(ii) 3RT1965-6A (Qty-02)(b) Following Contactors and timer relay of thruster starter no. 4 defective, to be replaced.(i) 3TF54 (Qty- 02)(ii) 3TF57 (Qty- 02)(iii) Timer relay (Qty-08)(c) Overhauling and bearing replacement of Thruster Motors in view of SPM reading observed in yellow zone. DE- NU7220 (Qty - 04), NDE- 7220B (Qty-04).Capacity - 371 KW each, 440V, 60Hz, 3Ø. |
| 1049 | (a) Carry out overhauling and bearing replacement of servo motor (3.5 kW, 440V, 60Hz) view SPM in yellow zone. Bearings no. DE- 6206ZZ (Qty-04), NDE- 6205ZZ (Qty-04).(b) Pressure gauges to be calibrated view showing erratic reading.(c) DR on Servo remote starting view not operational from Aft Thruster console at bridge |
| 1050 | (a) Liver Arms of 04 Thrusters and 02 Engine propultion to be replaced in view of generation alignment error. Qty - 06.(b) Feed back assembly of thrusters need to be replaced in view of faulty signals. Qty -03.(c) Adjustment and Calibration required in pitch actuator of all four thruster view slow response time. |
| 1051 | (a) Carry out replacement of desicant and nitrogen purging of pedestal assembly as per para 4.5.8 of INBR 1353 (ii).(b) DR of erratic feed of WSDS and GPS. |
| 1052 | (a) Overhaul the transmitter and receiver unit view malfunctioning, replace defective selector switches (06), push buttons(12) and indication lamp (12) view defective. |
| 1053 | (a)Replacement of following subunits of TVRO need to be undertaken in view signal tracking.(i) Antenna(ii) ACU(iii) Multiswitch(iv) Modulator (Qty-12)(v) Combiner(vi) Set Top Box (Qty-16)(vii) TVRO Amplifier (Qty-03) |
| 1054 | (b) TVRO RF Cables of following locations damaged and deteriorated, needs to be replaced:-(i) Antenna to Multiswitch(ii) Multiswitch to TVRO rack(iii) TVRO Rack to Amplifier(iv) Amplifier to 08 Containers & Barber Shop through Splitters(v) Amplifier to 09 Officers Cabin(vi) Amplifier to 07 SS Cabins(vii) Multiswitch to Wardroom, Dining Hall, Captains Cabin (Day & Night) & Sat Control Room |
| 1055 | Recabling of MCC 1,2 & 3 view low insulation observed. |
| 1056 | ELECTRICAL - PART III |
| 1057 | Installation of Repeaters of Log & Echosounder in MCR as per approved BPs |
| 1058 | Installation of Naval ADS-B as per approved BPs |
| 1059 | Installation of Second AIS as per approved BPs |
| 1060 | DIVING - PART I |
| 1061 | Test of positive buoyancy when loaded as if fully manned and equipped. |
| 1062 | Dry function test of all components and release mechanism of ballast weight. 06 guide wire socket bushes to be replaced. |
| 1063 | Following equipment function test of SDC to be carried out and proved:- (i) SDC Guide wire release system. (ii) Bell main wire release system. (iii) Umbilical cutter. (iv) Visual inspection / function test of emergency rescue system. |
| 1064 | Calibration of digital temperature gauge. |
| 1065 | Calibration all pressure gauges. |
| 1066 | Testing & Servicing of Tescom regulator at max working pressure. |
| 1067 | Visual examination and Ultrasound NDT of critical areas of lift attachment points of SDC. |
| 1068 | SDC Ultrasonic & magnetic particle Inspection of complet SDC. |
| 1069 | MPI of SDC Lifting hooks & pin. |
| 1070 | Valves, regulators and relevant fittings Gas leak test at maximum working pressure of the system. |
| 1071 | Bail out bottle thorough internal and external visual examination and gas leak test to maximum working pressure. |
| 1072 | SDC Umbilical pressure testing to max working pressure. Length 400 mtrs. High pressure hoses and SDC main umbilical’s to be examined for visual damage and tightness. |
| 1073 | Pressure testing of 02 LP diver’s umbilical hoses up to 35 bars. Length 50 mtrs each. |
| 1074 | Gas leak test at max. Working pressure of diver’s hot water hose. |
| 1075 | Servicing of main umbilical panel. (MARA Panel) |
| 1076 | Pressure testing of bell internal pipe lines as follows: - (i) Inlet pipe line 70 bars. (ii) Exhaust pipeline 500 PSI. (iii) Water pipe line 70 bars. (iv) All pipe work to be pressure tested to maximum working pressure. |
| 1077 | Testing and servicing of Tescom regulators. |
| 1078 | Testing and servicing of valves. |
| 1079 | Function testing and servicing of Gas panel. |
| 1080 | Testing and servicing of NRVs. |
| 1081 | Functional testing and servicing of Hot water panel. |
| 1082 | Painting of SDC internal surface as per scheme with hyperbaric paint. |
| 1083 | Painting of SDC external surface as per paint scheme |
| 1084 | Servicing and function test of external hatch spring locking arrangement. |
| 1085 | Replacement of Ó’ring of sealing (Mating) surface of internal hatch / external hatch |
| 1086 | Servicing and function test of internal hatch. Replacement of hatch if required. |
| 1087 | Check scrubber fan operation. Replace, if defective. |
| 1088 | Check marine connector, Replace, if damaged. |
| 1089 | Servicing of oil filled junction box. Replace transformer oil post overhauling . |
| 1090 | Check connectors of inside junction box, if any damage replaces connectors of junction box. |
| 1091 | Check all cable lugs, if any damage replace with new. |
| 1092 | Check batteries for capacity test. If found defective replace batteries. |
| 1093 | Check connectors and wirings for any deterioration. Renew as necessary / Replace, if defective. |
| 1094 | Overhauling of Communication System between Chamber and Control Panel. Amron communication system |
| 1095 | Overhauling of Helium scrambling systems. |
| 1096 | Overhauling & Function testing of Through water communication (TWC) |
| 1097 | Servicing of SDC BIBS. Replaced/ Renewal of SDC BIBS |
| 1098 | Replacemet/ Overhauling of deep diving first stage regulators |
| 1099 | 40001.40 Servicing and calibration of two CO2 analyzers. Replacement of 02 sensors. |
| 1100 | Testing and servicing of 52 valves. |
| 1101 | Testing and servicing of 04 Tescom regulators.(Replacement-02 regulators) |
| 1102 | Testing and servicing of 08 NRVs.(Replacement-04 NRVs) |
| 1103 | Painting of SDC internal surface as per scheme with hyperbaric paint. |
| 1104 | Painting of SDC external surface as per paint scheme. |
| 1105 | NDT/USG of complete SDC. |
| 1106 | Servicing and calibration of two O2 analyzers. Replacement of 02 sensors. |
| 1107 | Overhauling of camera supply in SDC control Room |
| 1108 | Functional test of electrical cables and equipment to be carried out. All components to be checked for insulation/continuity. Defective components (if any), to be replaced. |
| 1109 | Servicing and function test of bell main release system |
| 1110 | Servicing and functional test of Scrubbers and heaters. |
| 1111 | Servicing and functional test of Main Umblical cutter |
| 1112 | Servicing and functional test of Bell camera |
| 1113 | Servicing and alignment of clamping machanism. |
| 1114 | Servicing of Main supply junction box inside SDC |
| 1115 | Servicing of SDC umbilical panel. |
| 1116 | Calibration of digital tempreture gauge in SDC control room |
| 1117 | Overhauling of complete Pneumatic hoisting system. |
| 1118 | Main winch wire to be disconnected from winch drum and to be surveyed visually overall for corrosion/ chafing. |
| 1119 | Renew the brake pads when the distance between rail and the brake disc reaches 2 mm. |
| 1120 | Outer end to be re-socketed and white metal fitted with two existing retaining means. |
| 1121 | Complete assembly to be load tested thereafter as follows: - (i) Static Load- 1.5 times SWL (15 Tons) (ii) Functional Load test at SWL (12.5 Tons) (iii) Working load (10 Tons). |
| 1122 | Main Winch drum visual examination and NDT test of critical areas followed by function test at maximum SWL. |
| 1123 | Destruction test of wire sample taken beyond one sheave for determination of Factor of Safety (FOS). |
| 1124 | Overhauling and static load test of brake system of main winch to 1.25 times maximum SWL (12.5 Tons). |
| 1125 | Visual examination and NDT of critical areas of lift attachment points of diving bell followed by load test to 1.5 times max. SWL (10 tons). |
| 1126 | MPI of SDC winch – open spelter socket & pin. |
| 1127 | Pressure lubrication of entire length of wire 350 M. |
| 1128 | Calibration of SDC main wire counter & certification to issued for the same. Weight cell to measure weight to be provided as part of IMCA D018 regulations |
| 1129 | Visual examination and NDT (U/S or eddy currents as appropriate) of critical areas of Main Winch drum. |
| 1130 | Serviciability checks of main starter panel. |
| 1131 | Guide weight winch wire to be disconnected from winch drum and to be surveyed visually overall for corrosion/ chafing. |
| 1132 | MPI of SDC Guide weight winch – open spelter socket & pin. |
| 1133 | Renew the brake pads when the distance between rail and the brake disc reaches 2 mm. |
| 1134 | Outer end to be re-socketed and white metal fitted with two existing retaining means. |
| 1135 | Complete assembly to be load tested thereafter as follows: - (i) Static Load- 1.5 times SWL (1.5 Tons) (ii) Functional Load test at SWL (2 Tons) (iii) Working load (1 Tons). |
| 1136 | New Guide weight winch drum to be provide with grooves and spooling mechanism |
| 1137 | Destruction test of wire sample taken beyond one sheave for determination of Factor of Safety (FOS). |
| 1138 | Overhauling and static load test of brake system of Guide weight winch to 1.25 times maximum SWL (1.25 Tons). |
| 1139 | 40003.09 Visual examination and NDT of critical areas of lift attachment points of Guide weight followed by load test to 1.5 times max. SWL (2 tons). |
| 1140 | 40003.1 Pressure lubrication of entire length of wire 350 M. |
| 1141 | 40003.11 Calibration and overhauling/replacement of all wire counters. |
| 1142 | 40003.12 Calibration and overhauling/replacement of all wire counters. Calibration certificate to be issued for the same. |
| 1143 | Replacement of guide weight winch wire (350 m) each 44 mm. |
| 1144 | Calibration of overload relay of starters, certificate to be provided. |
| 1145 | Carry out chemical cleaning of hydraulic oil cooler. |
| 1146 | Renew ‘O’ seals of valves if found leaking. |
| 1147 | Renewal of brake band and disc spring inside brake cylinder. |
| 1148 | Load testing of load mate motor chain. |
| 1149 | Servicing of load mate motor |
| 1150 | Replace rubber coaming of moon pool hatch |
| 1151 | Check moon pool railing alignment. |
| 1152 | Check serviceability of solenoid valve, Replace, if defective. |
| 1153 | Load testing of deck fittings. |
| 1154 | Gas leak test at max working pressure of bell TUP clamp. |
| 1155 | Flushing of complete hydraulic lines. |
| 1156 | Servicing of TUP Hydraulic System. |
| 1157 | Safety interlock Pipe Work: - Visual examination and gas leak test at maximum working pressure. |
| 1158 | Hydraulic System:-Check oil leakage from pump. Renew seals, gaskets. |
| 1159 | Hydraulic pressure gauge calibration/replacement to be conducted. |
| 1160 | Servicing of Main valve of hydraulic tanks. |
| 1161 | Servicing of all hydraulic components of trolley. |
| 1162 | Servicing and alignment of SDC Cursure guide Railing. |
| 1163 | Clean the hydraulic oil tank and renew hydraulic oil if sample found contaminated. |
| 1164 | Analyze hydraulic oil or completely replace the oil and filter elements. |
| 1165 | Pressure testing and cleaning of Hydraulic oil cooler tube. |
| 1166 | Servicing of Pneumatic Hoisting System. |
| 1167 | Thorough external and internal visual inspection and Pressure testing of Pneumatic hoisting LP tank to full working pressure (i.e. 15 bars). |
| 1168 | Pressure Test of pneumatic hoses failing test replace Hoses. |
| 1169 | Chipping and painting of complete Trolley as per scheme. |
| 1170 | Replacement of defective hydraulic valves. |
| 1171 | Check serviceability of solenoid valve, Replace, if defective. |
| 1172 | Overhauling of Hydraulic mechanism of moonpool hatch |
| 1173 | Pressure testing of all the hydraulic pipelines. |
| 1174 | Gas leak test at max working pressure. |
| 1175 | Replacement of all view ports as part of PVHO guidelines and IMCA D 018 |
| 1176 | Calibration of humitidity and temperature sensors, certificate to be provided. |
| 1177 | Overhauling of all BIBS. Repalcement of 10 BIBS in DDC |
| 1178 | Overhauling of all Valves. |
| 1179 | Overhauling of Tescom regulators. |
| 1180 | Servicing, function testing and gas leak test at maximum working pressure of the following:- (i) Pipe work system. (ii) All Valves. (iii) Regulators and Relevant Fittings. |
| 1181 | Hyperbaric Fire Extinguisher:- Thorough external and internal visual examination and gas leak test to maximum WP(15 months). |
| 1182 | Function test to demonstrate operation of the Fixed fire fighting system. |
| 1183 | Sewage tanks of entry lock & Single lock to be through external and internal visual examination and gas leak test to maximum working pressure. |
| 1184 | Overhauling of main lock and single lock toilet valves. |
| 1185 | Medical lock overhauling alignment of medical lock doors. |
| 1186 | Check scrubber fan operation. Replace, if defective. |
| 1187 | Check marine connector, to be Replaced |
| 1188 | Carry out complete overhauling of pump motor, control panel and heaters. |
| 1189 | Camera, Light, DVR & Video Monitor:- Check connectors and wirings for any deterioration. Renew as necessary. |
| 1190 | Overhauling of Communication System between Chamber and Control Panel. |
| 1191 | Overhauling of Helium scrambling systems. |
| 1192 | Painting of DDC internal surface as per scheme with hyperbaric paint. |
| 1193 | Painting of DDC external surface as per paint scheme. |
| 1194 | Painting of all switchboards as per paint scheme. |
| 1195 | Replacement of all ‘O’Rings of DDC complex. |
| 1196 | Calibration of H2S monitor. |
| 1197 | Function test at required relief setting to maximum working pressure. |
| 1198 | Servicing of Medical lock. Alignment of medical lock. Replacement of shaft piston. Qty 02. |
| 1199 | Toilet valves for main lock and single lock to be overhauled. Replacement of 02 valves. |
| 1200 | Painting of DDC internal surface as per scheme with hyperbaric paint. |
| 1201 | Painting of DDC external surface as per paint scheme. |
| 1202 | Overhauling of Communication System between DDC and Sat control room (make-Amron. (Specifications - 220V, Talk back communication system). |
| 1203 | Servicing of all cameras in DDC |
| 1204 | Function test of fixed firefighting equipment- sprinkling system in DDC. |
| 1205 | Calibration of all depth gauges. |
| 1206 | Calibration of all pressure gauges. |
| 1207 | Servicing of all Tescom regulators. |
| 1208 | Replacement of all Valves.(quarter turn and needle)(Make : swagelok/ Parker) |
| 1209 | Upgradation of Sat Control Panel. |
| 1210 | Oxygen cleaning of pipe lines. |
| 1211 | Replacement of oxygen and carbon dioxide sensors. Make : Analox |
| 1212 | Overhauling of oxygen and carbon dioxide analyser. Replacement if defective |
| 1213 | Servicing and calibration of following measuring equipment. (Digital Meter) :- (i) Voltmeter 0 to 30 V – 04. (ii) Voltmeter 0 to 50 V – 02.(iii) Voltmeter 0 to 60 V – 01. (iv) Voltmeter 0 to 200 V – 02. (v) Voltmeter 0 to 300 V – 01. certificate to be provided. |
| 1214 | Serviceability checks of breakers in-situ. |
| 1215 | Serviceability checks of GSK relay and other protection circuits in-situ, certificate to be provided. |
| 1216 | Check phasing-in device type EPI. Clean thoroughly and carry out functioning Test. |
| 1217 | Repair/ replace busbars insulators if necessary. |
| 1218 | Clean and decarbonizes the busbars. |
| 1219 | Replacement of transformer |
| 1220 | Carryout out function test of Diving Switch Board. |
| 1221 | All valves of Air Inlet and Air exhaust to be overhauled. |
| 1222 | Overhaul pressure reducing valves and calibrate the measuring instruments. |
| 1223 | Servicing and pressure testing of relief valve to be carried out. Pressure to be set 11 Bars. |
| 1224 | Housing leak test to an internal pressure of 10 bars. |
| 1225 | Overhauling of SRB winch wire spooling mechanism. |
| 1226 | Lubrication /Galvanized Steel Wire Rope (length 225mtrs). |
| 1227 | Servicing and calibration of SRB winch wire counter. |
| 1228 | Pressure testing of SRB umbilical LP hoses up to 45 bars. |
| 1229 | Pressure testing of SRB Exhaust hose up to 500 PSI. |
| 1230 | High pressure hoses and SRB main umbilical’s to be examined for visual damage and tightness. |
| 1231 | Machining of upper, lower hatch and both mating surfaces of SRB. |
| 1232 | Overhauling/ servicing of SRB upper hatch closing mechanism. |
| 1233 | Change the rubber gaskets of the doors of the entrance and junction hatches and that of the supporting flange. |
| 1234 | Air pressure test of bell's air working chamber with internal pressure of 10 kgf/cm2 for leakage. |
| 1235 | Overhauling of pneumatic motor and gear assembly. |
| 1236 | Pressure testing of following Pipe lines:- (i) HP 4500 PSI (ii) Exhaust 500 PSI (iii) LP 70 Bars. |
| 1237 | Check scrubber fan operation. Replace, if defective. |
| 1238 | Check marine connector, Replace, if damaged. |
| 1239 | Check connectors of inside junction box, if any damage replaces connectors of junction box. |
| 1240 | Check all cable lugs, if any damage replace with new. |
| 1241 | Check batteries for capacity test. If found defective replace batteries. |
| 1242 | Check connectors and wirings for any deterioration. Renew as necessary. |
| 1243 | Overhauling of Communication System between Chamber and Control Panel. |
| 1244 | Overhauling of Helium scrambling systems. |
| 1245 | Painting of internal surface of SRB as per scheme with hyperbaric paint. |
| 1246 | Painting of external surface of SRB as per scheme. |
| 1247 | NDT/USG of complete SRB surface |
| 1248 | 'O' Ring of SRB matting surface and hatches to be replaced. |
| 1249 | Overhauling of water flow meter. |
| 1250 | MPI of SRB Lifting hooks & pin. |
| 1251 | Calibration of pressure gauges, certificate to be provided. |
| 1252 | Functional test of SRB mating adapter on TUP with SRB. |
| 1253 | Winch wire to be disconnected. Wire to be surveyed (visual) and tested to SWL of 1.5 Tons. Rewound on winch drum. 12mm |
| 1254 | Pressure testing of LSX LP and HP hoses. Replace if necessary.(300 Mtrs each). |
| 1255 | Servicing of SRB wire cutter. |
| 1256 | Compensating tank cleaning/painting and pressure testing at maximum working pressure. |
| 1257 | Overhauling of slipring. |
| 1258 | Servicing of all Sea water valves. |
| 1259 | Manufacturing of all J bolts as per design/ sample. Material : |
| 1260 | Gas leak test at max working pressure. |
| 1261 | Pressure leak test to maximum rated working pressure of whips and connectors. |
| 1262 | Calibration and overhauling of all pressure regulators. |
| 1263 | Servicing/ internal cleanliness appropriate to intended duty and gas leak test at maximum working pressure of the following:- (i) Pipe work system. (ii) All Valves. (iii) Regulators and Relevant Fittings. |
| 1264 | Overhauling of Tescom regulators. |
| 1265 | Medical lock overhauling alignment of medical lock doors. |
| 1266 | Replacement of all ‘O' Rings of all chamber doors. |
| 1267 | Check scrubber fan operation. Replace, if defective. |
| 1268 | Check marine connector, Replace, if damaged. |
| 1269 | Camera, Light, DVR & Video Monitor:- Check connectors and wirings for any deterioration. Renew as necessary. |
| 1270 | Painting of Chamber internal surface as per scheme with hyperbaric paint. |
| 1271 | Painting of Chamber external surface as per paint scheme. |
| 1272 | Function test at required relief setting to maximum working pressure. |
| 1273 | Repalcement Viewports as part of PVHO guidelines and IMCA D 018 |
| 1274 | Painting of Therapeutic Chamber internal surface as per scheme with hyperbaric paint. |
| 1275 | Painting of Therapeutic Chamber external surface as per scheme with hyperbaric paint. |
| 1276 | CO2 and O2 analyser to functionally tested. |
| 1277 | Servicing of SAECO valve and bell equipments. Check operation. |
| 1278 | Calibration of pressure Gauges. |
| 1279 | Servicing of SAECO valve and bell equipments. Check operation. |
| 1280 | Calibration of pressure Gauges. |
| 1281 | Servicing of SAECO valve and bell equipments. Check operation. |
| 1282 | Calibration of pressure Gauges. |
| 1283 | Servicing of SAECO valve and bell equipments. Check operation. |
| 1284 | Servicing and replacement of filters (F1, F2, & F3). |
| 1285 | Overhauling of BPR regulators. |
| 1286 | Overhauling of reclaim bell equipment. |
| 1287 | Servicing of oxygen panel. |
| 1288 | Servicing of helium reclaim control panel. |
| 1289 | Servicing of Bell external water Trap unit. |
| 1290 | Function test at required relief setting to maximum working pressure. |
| 1291 | R1& R2 bottle thorough internal and external visual examination and gas leak test to maximum working pressure. |
| 1292 | Servicing and Function test of CO2 Scrubber. |
| 1293 | Independent static load test on each break system at 1.5 times max. SWL - 1 ton. |
| 1294 | Cut back SWR rope beyond first sheave and test to destruction to prove safety factor. |
| 1295 | Re-terminate and apply static load test at 1.5 times SWL. |
| 1296 | Load test of Lift Attachment Point at 1.5 times max.SWL followed by NDT of critical area. |
| 1297 | Winch drums brake to be overhauled and checked for SWL up to 02 Tons. |
| 1298 | Calibration of all hydraulic pressure gauges. |
| 1299 | Calibration of overload mechanism of the starter. |
| 1300 | Calibration of winch and ram gauges. |
| 1301 | Hydraulic Fluid/Oil analyzed or completely replaced. Clean and renew oil filters on the tank and calibrate main hydraulic pump pressure. |
| 1302 | Overhauling of SDS pump. Defective components to be replaced. |
| 1303 | Overhauling of hydraulic cylinders. |
| 1304 | Electrical Components:- Overhauling of 440 V 60 Hz 3 Phase 30 KW motor and starter calibration of OLR, certificate to be provided. |
| 1305 | Pressure testing of 02 diver main supply hoses of umbilical up to 45 bar. Length 100 m. |
| 1306 | Electrical insulation test for 04 in nos electrical & communication cables of diving umbilical. Length 100m. |
| 1307 | Servicing and internal cleanliness appropriate to intended duty and gas leak test at maximum working pressure of the following:-(i) Pipe work system. (ii) All Valves. (iii) Regulators and Relevant Fittings. |
| 1308 | Check serviceability of solenoid valve, Replace, if defective. |
| 1309 | Camera, Light, DVR & Video Monitor:- Check connectors and wirings for any deterioration. Renew as necessary. |
| 1310 | Overhauling of Communication System between Diver helmet and Control Panel. |
| 1311 | Overhauling of Helium scrambling systems. |
| 1312 | Mix Gas Dive panel:- Oxygen cleaning of pipelines. |
| 1313 | OBG air bottle: - Thorough internal and external visual inspection, hydraulic pressure test and chemical cleaning and drying (as per OEM manual). |
| 1314 | Replacement of SDS first stage regulators for emergency bailout bottles |
| 1315 | Replacement of SDS cage view deteriotion. Design : As per sample. Material : SS 316 |
| 1316 | Calibration of pressure gauge. |
| 1317 | Gas leak test at Max WP of all pipe works and valves. |
| 1318 | Through External visual examination and gas leak test to maximum working pressure of all cylinders.(30 cylinders in each quad) |
| 1319 | Servicing and Gas leak test at maximum working pressure of all valves. |
| 1320 | Replacement of canvas covers |
| 1321 | Chipping, repairs and painting of quads frames. |
| 1322 | Clean the separator, empty the condensate collector. |
| 1323 | Exchange intake filter – element. |
| 1324 | Leak testing and general visual inspections of both compressor. |
| 1325 | Check terminal clamps for tightness. |
| 1326 | Change seals, o-rings acc. |
| 1327 | Pressure vessel sight control, recording hours and counting of cycles of both compressore. |
| 1328 | Pressure relief valve control, may obstruct change. |
| 1329 | Change final separator filter cartridge. |
| 1330 | If necessary exchange filter cartridge / dryer system of both compressor. |
| 1331 | Check functional testing, final inspection and test run of both compressore. |
| 1332 | Check v-belt and fan blades. Replace if damaged |
| 1333 | Check functionality, automatic condensate drain of both compressore. |
| 1334 | Overhaul automatic condensate drain of both compressore.. |
| 1335 | Exchange oil filter cartridge of both compressore.. |
| 1336 | Check suction, pressure valve of stages of both compressore.. |
| 1337 | Check intermediate pressure and oil pressure of both compressore.. |
| 1338 | Exchange oil of both compressore.. |
| 1339 | Check safety valves, if there are no test options than exchange. |
| 1340 | Exchange seals, o-rings acc. to maintenance kit. of both compressore. |
| 1341 | Check temperature sensor. |
| 1342 | Check wearing of cylinders, pistons and piston-rings, if necessary replace of both compressore.. |
| 1343 | Exchange v-belt. |
| 1344 | Visual check of piston and cylinder. |
| 1345 | Check bearer rings and seal rings of piston and cylinder. |
| 1346 | Check belt tension. |
| 1347 | Drain and replace oil. |
| 1348 | Clean oil strainer. |
| 1349 | Replace oil filter. |
| 1350 | Check compensating pump and grease eccentric of hydraulic oil circuit. |
| 1351 | Clean oil cooler. |
| 1352 | Replace or refurbish of gas valve. |
| 1353 | Replace wiper ring of oil wiper. |
| 1354 | Visual check for wear of Vee belt drive. |
| 1355 | Visual check bar over of gearbox. |
| 1356 | Alignment check of gearbox. |
| 1357 | Check Piston rings. |
| 1358 | Check crosshead/ cylinder and piston/cylinder clearance. |
| 1359 | Check small end pin bush clearance. |
| 1360 | Check bearings of crankshaft and connected rod. |
| 1361 | Check crosshead/ crosshead sleeve clearance of piston and cylinder. |
| 1362 | Calibration of Gauges. |
| 1363 | Calibration of temperature and Humidity Sensor. |
| 1364 | Cleaning of glycol water tubes with brush in cooling unit. |
| 1365 | Gas leak test of all pipe work at max. WP. |
| 1366 | Serviceability checks of hermitically sealed compressors. |
| 1367 | Calibration of HP and LP cut-outs. |
| 1368 | Overhauling of primary and secondary pumps. |
| 1369 | Servicing of Solenoid valves, renew if defective |
| 1370 | Serviceability Checks and continuity test of all electric components of the CMU. |
| 1371 | Actuators to be replaced. |
| 1372 | Sea water coolers to be chemically cleaned. |
| 1373 | Replacement of Danfoss Heat exchanger plates. |
| 1374 | Carry out complete overhauling of pump motor, control panel and heaters. |
| 1375 | Overhauling of sea water system. |
| 1376 | Function test of all relief valves and their calibration at max. WP. |
| 1377 | Internal overpressure test plus gas leak test to full WP of all gas receivers. |
| 1378 | Functional test and calibration of all relief valves. |
| 1379 | Functional testing of heating element of CMU. Defective elements to be replaced. |
| 1380 | Carry out performance trial of the pump including parameter checks (suction/discharge pressure), vibration trials, insulation/SPM checks on motor, motor starting-running current checks etc. assess for satisfactory performance and defects, if any. |
| 1381 | Undertake overhaul of 25% of total standalone centrifugal pump (including those recommended by trial agencies). Undertake performance trials of overhauled pumps. |
| 1382 | Calibrate all instrumentation, certificate to be provided. |
| 1383 | Inspect and renew if required the suction strainer. |
| 1384 | Check conditions of rubber inserts, metal shims etc in coupling and renew, if required. |
| 1385 | Refit 25% of suction and discharge valves. |
| 1386 | Analysers to examined, function tested and calibrated. |
| 1387 | Check operation of oxygen and carbon dioxide analysers. If found defective, replace the same. |
| 1388 | Replace O2 and CO2 sensors (As per shelf life of sensors). Make : Analox) |
| 1389 | Both Anode Plugs to be replaced |
| 1390 | 18 in number pressure gauges to be calibrated, Anticipatory replacement of 05 gauges. |
| 1391 | 05 defective sea water inlet/outlet valves to be replaced. |
| 1392 | All heating elements of WHE/MHE to be cleaned. Total 48 in nos. |
| 1393 | 02 Inlet filters to be changed |
| 1394 | Condition of inner walls of cylinders of both WHE and MHE to be checked. If worn out cylinders to be replaced. |
| 1395 | All 'O' rings of WHE and MHE to be replaced. |
| 1396 | Overload mechanism of WHE/MHE to be calibrated, certificate to be provided. |
| 1397 | Servicing of pumps. |
| 1398 | Calibration of pressure Gauges. |
| 1399 | Servicing and Function test of Blast proof Charging Bay. |
| 1400 | Function test at required relief setting to maximum working pressure. |
| 1401 | Gas leak test at Max WP of all pipe works and valves. |
| 1402 | Replacement of all flexible hoses. |
| 1403 | Calibration of Pressure Gauges. |
| 1404 | Servicing of Tescom Regulators. |
| 1405 | Calibration of Digital Readout Alarm. |
| 1406 | Gas leak test at Max WP of all pipe works and valves. |
| 1407 | Servicing and function test of Gas Blender System. |
| 1408 | Function test at required relief setting to maximum working pressure. |
| 1409 | Through external visual examination and gas leak test to max working pressure |
| 1410 | Calibration of pressure gauges. |
| 1411 | Gas leak test at Max WP of all pipe works and valves. |
| 1412 | GDP hoses to be pressure tested to WP (330 Bars) Defective hoses to be replaced. |
| 1413 | Servicing of all Tescom regulators. |
| 1414 | Painting of all Kelly Bottles. |
| 1415 | Through External visual examination and gas leak test to maximum working pressure of Kelly Bottles. |
| 1416 | Replacement of niddle valves, QRC coupling and manifold assembly |
| 1417 | Relief valve setting at requisite pressure on all Kelly Bottles, GDP and ADP. |
| 1418 | Replace the air intake cartridge. |
| 1419 | Replace the coalescing cartridge. |
| 1420 | Change of oil. and pour new oil. |
| 1421 | Synthetic lube oil has to be changed. |
| 1422 | Replace valves. |
| 1423 | Replace pistons and piston ring. |
| 1424 | Complete overhauling of the pump; Dismantle the pump. |
| 1425 | Replace all rubber parts of the pump. |
| 1426 | Check bearing. Replace if found defective. |
| 1427 | Check the connecting coupling of the pump. If any abnormalities in rubber parts then replace the spindle of coupling. |
| 1428 | Check the performance of the pump and re-install in the system and check again. |
| 1429 | Check contacts and wirings for wear/ deterioration. Renew as necessary. |
| 1430 | Carry out the alignment of the pump driven unit with the motor (if necessary). |
| 1431 | Carry out SPM checks. Lubricate/ replace bearings as necessary (Raise specific defects to dockyard). |
| 1432 | Carry out inspection of rubber gaskets between the covers and shell body of starters. Check motor terminal box sealing. Renew, if required. |
| 1433 | Carry out proper tightening of seals in water tight modules. Replace, if necessary. |
| 1434 | Calibrate the Over-load mechanism of the starter, certificate to be provided. |
| 1435 | Calibrate the over-load mechanism of the starter, certificate to be provided. |
| 1436 | Lubricate/ replace bearings as necessary. |
| 1437 | Overhaul motor and starter subject to QC checks. Carry out Trials on completion of repairs. |
| 1438 | Replace the spark plugs. |
| 1439 | Replace the water pump impeller. |
| 1440 | Inspect the wire harness connectors. |
| 1441 | Inspect the engine motor mounts. |
| 1442 | Change the engine oil and filter. |
| 1443 | Inspect the thermostat, saltwater or brackish water only. |
| 1444 | Replace the Quickleen to the fuel tank. |
| 1445 | Replace the gear lubricant. |
| 1446 | Inspect the corrosion control anodes. |
| 1447 | Lubricate the propeller shaft splines. |
| 1448 | Replace all filters on the suction side of the fuel system. |
| 1449 | Check the torque of the outboard mounting hardware. |
| 1450 | Servicing and functional tested by M/s Videoray |
| 1451 | Replacement of damage parts using hardware replacement and software configuration procedures as per manual by OEM. |
| 1452 | Function test and software up gradation by M/s Videoray |
| 1453 | Complete overhauling of the tools, Dismantle the tools. |
| 1454 | Check bearing replace if found defective. |
| 1455 | (C) Check the connecting coupling of the tools if any abnormalities in rubber parts then replace the spindle of coupling. |
| 1456 | Servicing and function test of all components. |
| 1457 | The complete assembly is to be proof-tested to max working pressure. |
| 1458 | Overhauling of Oxygen regulators. |
| 1459 | Pressure test of flexible oxygen pipes up to max working pressure. |
| 1460 | Overhauling of Cutting / Welding Torch |
| 1461 | Load Test of shackles. |
| 1462 | Replacement of lifting strops. |
| 1463 | Servicing of all valves. |
| 1464 | Pressure test of LP hoses at max working pressure. |
| 1465 | Calibration and functional test of relief valves. |
| 1466 | Inflation of bag post fitment of test plug against leakage, wears, cut and abrasion. |
| 1467 | Overhauling, Repair and replacement of defective bags with manufacturer approved parts. (Make : Subsalve, USA) |
| 1468 | Replacement of Air intake filter. |
| 1469 | Clean or flush through crank case after draining oil and charge it with new oil. |
| 1470 | Check all the relief valves for its proper functioning and reset valve. |
| 1471 | Tighten all the bolts with torque spanner for retorque. |
| 1472 | Check operation of low oil level switch. |
| 1473 | Carry out performance test. |
| 1474 | Clean air flow passage of after cooler internally. |
| 1475 | Check moter bearing and lubricate bearing. |
| 1476 | Replacement of NRVs. |
| 1477 | Servicing and fuction test of Superlite 17C Helmet (Ultra Jewel). Renewal of complete repair Kit. (Make : Kirby Morgan) |
| 1478 | Servicing and fuction test of Superlite 37 B Helmet. Renewal of complete repair Kit. (Make : Kirby Morgan) |
| 1479 | Servicing and fuction test of Superlite 18 B (Bandmasks). Renewal of complete repair Kit. (Make : Kirby Morgan) |
| 1480 | Major LRS Survey to be undertaken during the maintenance period of saturation diving system and air diving system. Certification of systems to be undertaken. |
| 1481 | DIVING - PART II |
| 1482 | Servicing of solenoid valves. Replacement of 01 solenoid valves. Defective components if any to be replaced. |
| 1483 | Switches/ lamps to be replaced. |
| 1484 | Servicing of operating pannels (guide weight and trolly) |
| 1485 | Overhauling of Guide weight hydraulic pump. Anticipatory replacement of bearings and seals. |
| 1486 | Guide weight contol Panel Painting/Polishing(Steel Paint) |
| 1487 | Overhauling of Clamp motor (qty-01). Anticipatory Replacement/repair of worn-out/damaged motor components |
| 1488 | Servicing of 04 solenoid valves. Replacement 01 solenoid valve |
| 1489 | Replacement of bushes & shaft of TUP clamp. |
| 1490 | Replacement of corroded metalic stanchions (fixed guardrails) near operating pannel/ SDC. |
| 1491 | Safety interlocks for clamping mechanism to be calibrated. Anticipatory replacement of pressure switch |
| 1492 | Carry out survey and functional test of entire hydraulic system. Change/repair defective components. |
| 1493 | 12 Greasing nipples to be flushed and renewal if required. |
| 1494 | Chemical cleaning of sea water coolers (total 02) to be carried out. Anticipatory replacement of 01 cooler |
| 1495 | Overhauling of Trolley and Guide weight hydraulic pump motors. |
| 1496 | Cleaning of hydraulic oil main tank |
| 1497 | Repair/ replacement of 03 defective gauges. |
| 1498 | Overhauling of 06 speech scrambling systems (Make Amron).Defective components to be replaced. |
| 1499 | Replacement of 05 defective depth gauges. |
| 1500 | Ó'Ring of Main Lock , Entry Lock, VTT, HTT & Medical Lock to be replaced. |
| 1501 | VTT Hydraulic Motor & pump to be overhauled.Dective part to be replaced (if any). |
| 1502 | Servicing of 03 CO2 Analysers. Replacement of 03 CO2 sensors. |
| 1503 | Tescom regulators to be overhauled. Replacement of 03 regulators |
| 1504 | Servicing of 02 Helium analysers. Replacement of 02 Helium sensors |
| 1505 | All HP pipe lines (Tungum), valves and connections of SDC control room, sat control room and other diving sytems to be chemicaly cleaned and pressure tested to 1.1 times of WP. Length 450 m. Pipe failing pressure test to be replaced. Anticipated replacement 30 mtrs. |
| 1506 | Replacement of 15 Nupro filter. |
| 1507 | Replacement of Diving switch board indication lamps |
| 1508 | All switches and other components of light panel to be changed as per chamber light voltage. |
| 1509 | Insulation meter replacement with digital insulation meter. |
| 1510 | Replacement of EDA KW meter with new KW meter including CT. |
| 1511 | Generator guard of EDA and main section (for 800A ACB) section to be replaced with new guard of same specification. |
| 1512 | KW meter and Ammeter of main section to be replaced of low rating including CTs. (300 KW & 500 Amps) |
| 1513 | Switch cum Fuse panel of Sat Control Room non ops. To be replaced. (220V AC, 30V AC, 24V DC of Main Lock & 24V DC of Single Lock) with provision of dimmer. |
| 1514 | 220V AC TV, Analyser & Actuator switch socket replacement (07 in no.) |
| 1515 | Remote ON/OFF push button of EDA non-ops. To be repaired. |
| 1516 | SDC contactor of (110V, 220V, 24V DC) to be replaced. |
| 1517 | Servicing of 02 flow meter. Replacement of 01 flow meter. |
| 1518 | Serviceability checks of SRB main lock camera, Amron microphone, lights and scrubber are to be carried out. All defective components to be repaired/replaced. Anticipatory replacement of Amron microphone and scrubber fan 02 each. |
| 1519 | Replacement of winch wire (11mm Galvanized Steel Wire Rope, rotating, length 200 mtrs) of SRB tested to 2.25 Tons (SWL of 1.5 Tons). Along with thimble eye on one end. |
| 1520 | Air lock to main working chamber hatch nuts to be replaced. |
| 1521 | O' Ring of SRB matting surface to be replaced |
| 1522 | Replacement of upper hatch O-Ring. |
| 1523 | Replacement of Middle Hatch O-Ring. |
| 1524 | Painting of internal surface of SRB as per scheme with hyperbaric paint. |
| 1525 | Housing leak test to internal pressure of 10 bar. |
| 1526 | Machining of upper, lower hatch and both mating surfaces of SRB. |
| 1527 | Lower hatch to be aligned. |
| 1528 | NDT/USG of complete SRB surface |
| 1529 | Alignment of upper hatch of SRB. |
| 1530 | Provisioning of pump and accumulator (20 ltrs) for supplying liquid food to Submarine at 150 mtrs (16 bar). |
| 1531 | Painting of external surface of SRB as per scheme. |
| 1532 | Hydrogen burner to be replaced |
| 1533 | Replacement of 02 portable hyperbaric CO2 monitor in SRB. |
| 1534 | Air lock to main working chamber hatch nuts to be replaced. |
| 1535 | Servicing of scrubber fan and replacement of stainer. |
| 1536 | One defective CO2 analyser to be replaced |
| 1537 | Servicing of 02 in number Tescom regulator to be carried out. Defective parts to be replaced |
| 1538 | Replacement of 'O' rings. |
| 1539 | Winch drum brake to be overhauled and checked for SWL upto 01 Tons. |
| 1540 | Calibrate the overload mechanism of the starter. |
| 1541 | Electrical insulation test for 02 in nos electrical & communication cables of diving umbilical. Length 100m. |
| 1542 | Overhauling of starter panel. |
| 1543 | Replacement oil filter, drain and replace oil. |
| 1544 | Cleaning/ replacement of oil strainer. |
| 1545 | Both Anode Plugs to be replaced |
| 1546 | Anticipatory replacement of 05 pressure gauges. |
| 1547 | Flexible hose with brass end fittings to be replaced. |
| 1548 | Temperature controller erratic needs repair/replacement. |
| 1549 | Visual examination, functional testing and continuity test of all electric components of the CMU. Defective components to be replaced. |
| 1550 | Sea water coolers to be chemically cleaned. |
| 1551 | Provisioning of oxygen depletion sensor Analox O2NE plus for warning of leakege of helium gas near kelly bottles with indication in DDC area/ sat control room. |
| 1552 | Function test of helium reclaim system. |
| 1553 | Replacement of 04 webbing strops of capacity 05 tons. |
| 1554 | Replacement of 02 webbing strops of capacity 12 tons. |
| 1555 | 04 in number defective diving LED hat lights to be replaced. 300 mtr rating, 5000 lumen. |
| 1556 | Replacement of 06 damaged hot water suits and 06 inner suits. |
| 1557 | Replacement of all defective CO2 & O2 analysers including those failing functional tests. |
| 1558 | 06 Cal/ Zero gas regulators defective. To be replaced. |
| 1559 | Replacement of 08 in no defective rotary switches in diving switchboard. |
| 1560 | 05 in no temperature/humidity hygrometers damaged. Serviceability checks to be carried out. To be repaired/replaced if defective. |
| 1561 | INSTRUCTIONS ON SECURITY, SAFETY AND MOVEMENT |
| 1562 | (A) SHIPYARD TO QUOTE FOR ALL SERIALS. BULK/LUMPSUM COSTING IS NOT ALLOWED. ALL PAYMENTS WILL BE ON ACTUALS ON NOT EXCEEDING BASIS. (B) ALL SPARES ARE TO BE SOURCED THROUGH OEM AND OEM SUPERVISION IS TO BE ENSURED FOR ROUTINE/REPAIRS OF ALL EQUIPMENT.(C) IF SHIP REFIT AT SHIPYARD CONTINUES BEYOND 150 DAYS FOR ANY REASON INCLUDING FORCE MAJEURE, ALL ADMIN/GENERAL SERVICES ARE TO BE EXTENDED WITHOUT ADDITIONAL COST. |
| 1563 | PASSES OF ALL NIREEKSHAK PERSONNEL TO BE MADE AND PRIORITY CLEARANCE FOR ALL PERSONNEL OF THE SHIP DURING ENTIRE DURATION OF REFIT |
| 1564 | SHIPYARD IS REPONSIBLE FOR THE SAFETY OF THE VESSEL AND THE VESSEL'S PROPERTY FROM INCLEMENT AND ADVERSE WEATHER, FOR SAFETY AND SECURITY OF ALL ITEMS/ MATERIAL/EQUIPMENT THAT IS DEGUTTED/REMOVED FROM ONBOARD THE SHIP AND THE SAME ITEM IS TO BE FITTED ONBOARD. SHIPYARD IS TO ESTABLISH A SECURITY PERIMETER AROUND THE VESSEL WITH 2 SENTRIES ROUND THE CLOCK. SHIPYARD EXECUTIVES/STAFF/WORKERS/CONTRACTORS SHALL STRICTLY ABIDE BY ALL NAVAL PROCEDURES / INSTRUCTIONS INTIMATED VERBALLY OR IN WRITING BY SHIP'S OFFICERS AND PROJECT MONITORING OFFICERS. ALL SHIPYARD WORKERS /CONTRACTORS /STAFF ENTERING ONBOARD FOR WORK SHALL BE IN POSSESSION OF VALID ID CARDS AND SHALL SHOW THE SAME WHILE ENTERING/LEAVING OR AS DIRECTED. THE PASSES FOR OFFICERS, PMT AND SAILORS (INCLUDING CAR & BIKE) TO BE ISSUED WITHIN 5 DAYS OF THE ARRIVAL OF THE VESSEL WITH VALIDITY TILL COMPLETEION OF REFIT. THE ENTRY/ EXIT TO SHIP YARD WILL CONTINUE EVEN IN ABSENCE OF SHIP YARD PASSES. |
| 1565 | PRIORITY CLEARANCE TO ALL NAVAL OFFICERS FOR ENTRY/EXIT TO SHIPYARD, SAILORS OF THE SHIP AND PROJECT MONITORING TEAM TO BE GIVEN SPECIAL CHANNEL FOR UNINTERRUPTED MOVEMENT).SHIPYARD TO PERMIT UNRESTRICTED ENTRY /EXIT OF MATERIAL/ SPARES/ ITEMS/ EQUIPMENTS ON SHIP'S AND PROJECT MONITORING OFFICER'S LETTER AT ANY HOUR OF THE DAY. IMMEDIATE CLEARANCE (WITHIN 05 MIN) TO BE GIVEN BY SHIPYARD ON VERBAL INTIMATION/EMAIL/LETTER FROM SHIP AND PROJECT MONITORING TEAM.SHIPYARD TO PERMIT ENTRY/EXIT OF INDIVIDUALS OF ANY FIRM /COMPANY/ORGANIZATION /GUESTS ONBOARD THE VESSEL ON SHIPS AND PROJECT MONITORING OFFICERS LETTER. PREFERRENTIAL /IMMEDIATE CLEARANCE(WITHIN 05 MIN) TO BE GIVEN BY SHPYARD BY VERBAL INTIMATION /EMAIL/LETTER FROMN SHIP OR PROJCT MONITORING TEAM. ALL SHIPYARD WORKERS/SUBCONTRACTORS ETC TO BE CHECKED/SCANNED PRIOR ENTRY ONBOARD THE SHIP AND ALSO ALL ITEMS/BAGS TO BE X-RAYED. CCTV RECORD (WITH NIGHT VISION) OF THE ENTIRE SHIP'S PERIMETER TO BE MAINTAINED FOR THE DURATION OF REFIT AND BACK UP OF ATLEAST 30 DAYS TO BE MAINTAINED. |
| 1566 | INSTRUCTIONS ON DD & WHARFAGE |
| 1567 | PD1 - THE REFITTING AUTHORITY IS TO TAKE ALL ACTIONS TO ENSURE THAT THE DOCKING IS CARRIED OUT IN ACCORDANCE WITH THE LATEST ISSUE OF THE DOCKING PLAN FOR THE PLANNED VERSION OF THE DOCKING WHICH IS SPECIFIC TO THE VESSEL (AND NOT GENERIC TO A CLASS OF VESSELS) AND FOR A PARTICULAR DOCKING PROCEDURE. THE REFITTING AUTHORITIES ARE TO FORWARD DOCKING PLAN, ALONG WITH THE CHECK OFF LIST PROMULGATED VIDE NC/POLICY/H-134/REFIT DATED 11 MAY 18, TO IHQ(N)/DNA THROUGH COMMAND HQS FOR APPROVAL. THE DOCKING FACILITY IS TO BE PREPARED IN ACCORDANCE WITH THE REQUIREMENTS OF THE DOCKING PLAN AND DOCKING PROCEDURES. SR- 26 |
| 1568 | PD2 - A DOCK MASTER IS TO BE APPOINTED BY THE REFITTING AUTHORITY FOR EACH DOCKING EVOLUTION AND THE SAME IS TO THE INTIMATED TO COMMANDING OFFICER/ MASTER OF THE VESSEL AS PER FORMAT OF NO STR 01/11, PREFERABLY 72 HOURS IN ADVANCE OF THE COMMENCEMENT OF DOCKING EVOLUTION.SR- 26 |
| 1569 | PD4 - REFITTING AUTHORITY (DOCK MASTER AND PLANNER) ARE TO REVIEW THE CALCULATION SUBMITTED BY THE SHIP. THE DOCKING/ UNDOCKING CONFERENCES ARE TO BE ORGANISED BY THE REFITTING AUTHORITY (DOCK MASTER AND REFIT PLANNER) TO REVIEW READINESS FOR DOCKING/ UNDOCKING OPERATIONS, AT LEAST 24 HOURS PRIOR DOCKING/ UNDOCKING. FURTHER, IN ORDER TO UNDERSTAND CRITICALITY OF EACH OPERATION, AND DEMARCATION OF RESPONSIBILITIES OF THE STAKEHOLDERS, THE DOCK MASTER IS TO CONDUCT A CENTRALISED BRIEFING FOR ALL THE STAKEHOLDERS 24 HOURS PRIOR EVERY DOCKING/ UNDOCKING OPERATION.SR- 26 |
| 1570 | DRY DOCKING & WHARFAGE |
| 1571 | DOCK BLOCK PREPARATION FOR DOCKING OF SHIP IN VERSION - II, BOTH CENTER LINE AND SIDE BLOCKS. SHIPYARD TO ARRANGE FOR THIRD PARTY INSPECTION AND HAND OVER DULY RECOMMENDED CERTIFICATE FOR DOCK BLOCK PREPARATION TO NAVY POST INSPECTION |
| 1572 | DOCKING AND UNDOCKING OF THE VESSEL IN VERSION- I (DURATION 30 DAYS). SHIPYARD TO PLAN AND COMPLETE ALL DRY DOCK RELATED WORK WITH IN DRY DOCK TIME. ELSE SHIPYARD TO CONTINUE DOCKING OF SHIP ALONG WITH ALL ALLIED SERVICES TILL COMPLETION OF WORK WITH OUT ANY EXTRA COST. PAYMENT WILL BE RESTRICTED TO ACCEPTED PERIOD OF CONTRACT |
| 1573 | DOCKING & UNDOCKING (QUOTE AS ONE UNIT) |
| 1574 | SUBSEQUENT DAYS IN DOCK. |
| 1575 | ARRANGE TUG AND PILOTAGE FOR TAKING THE VESSEL FROM NAVAL JETTY TO THE DOCK, DOCKING, UNDOCKING & DELIVERY OF VESSEL BACK AT NAVAL JETTY. PAYMENT BASED ON THE ACTUAL TIMES AS PER WCC ON NOT EXCEEDING BASIS. |
| 1576 | MOORING/UNMOORING AND LINE HANDLING FOR EACH OPERATION |
| 1577 | PROVIDE WHARFAGE / WET BASIN FACILITIES (WITH 6M DEPTH AT ALL CONDITIONS) AS REQUIRED FOR COMPLETION OF WORK PACKAGE. DREDGING AS REQUIRED TO BE CARRIED OUT PRIOR TO COMMENCEMENT OF REFIT AT SHIPYARD'S COST. PAYMENT WILL BE RESTRICTED TO ACCEPTED PERIOD IN THE CONTRACT |
| 1578 | ON DOCKING OF SHIP, ALL MARINE GROWTH ON PROPELLER TO BE SCRAPPED OF USING SUITABLE METHOD BY SHIPYARD. PROPELLER TO BE PRESERVED AND ALSO CLEANING TO BE UNDERTAKEN AS PER IN STANDARDS |
| 1579 | TECHNICAL SUPPORT SERVICES |
| 1580 | SHIPYARD IS REPONSIBLE FOR THE SAFETY OF THE VESSEL AND THE VESSEL'S PROPERTY FROM INCLEMENT AND ADVERSE WEATHER |
| 1581 | SHIPYARD IS RESPONSIBLE FOR SAFETY AND SECURITY OF ALL ITEMS/ MATERIAL/EQUIPMENT THAT IS DEGUTTED/REMOVED FROM ONBOARD THE SHIP AND THE SAME ITEM IS TO BE FITTED ONBOARD |
| 1582 | SHIPYARD IS TO ESTABLISH A SECURITY PERIMETER AROUND THE VESSEL WITHIN 2 SENTRIES ROUND THE CLOCK |
| 1583 | SHIPYARD EXECUTIVES/ STAFF/ WORKERS/CONTRACTORS SHALL STRICTLY ABIDE BY ALL NAVAL PROCEDURES / INSTRUCTIONS INTIMATED VERBALLY OR IN WRITING BY SHIP'S OFFICERS AND PROJECT MONITORING OFFICERS. |
| 1584 | ALL SHIPYARD WORKERS /CONTRACTORS /STAFF ENTERING ONBOARD FOR WORK SHALL BE IN POSSESSION OF VALID ID CARDS AND SHALL SHOW THE SAME WHILE ENTERING/LEAVING OR AS DIRECTED |
| 1585 | THE PASSES FOR OFFICERS, PMT AND SAILORS TO BE ISSUED WITHIN 02 DAYS OF THE ARRIVAL OF THE VESSEL WITH VALIDITY TILL COMPLETION OF REFIT. THE ENTRY/ EXIT TO SHIP YARD WILL CONTINUE EVEN IN ABSENCE OF SHIP YARD PASSES |
| 1586 | PRIORITY CLEARANCE TO ALL NAVAL OFFICERS FOR ENTRY/EXIT TO SHIPYARD, SAILORS OF THE SHIP AND PROJECT MONITORING TEAM TO BE GIVEN SPECIAL CHANNEL FOR EASE OF MOVEMENT. |
| 1587 | SHIPYARD TO PERMIT UNRESTRICTED ENTRY /EXIT OF MATERIAL/ SPARES/ ITEMS/ EQUIPMENTS ON SHIP'S AND PROJECT MONITORING OFFICER'S LETTER AT ANY HOUR OF THE DAY. IMMEDIATE CLEARANCE (WITHIN 05 MIN) TO BE GIVEN BY SHIPYARD ON VERBAL INTIMATION/EMAIL/LETTER FROM SHIP AND PROJECT MONITORING TEAM |
| 1588 | SHIPYARD TO PERMIT ENTRY/EXIT OF INDIVIDUALS OF ANY FIRM /COMPANY/ORGANIZATION /GUESTS ONBOARD THE VESSEL ON SHIPS AND PROJECT MONITORING OFFICERS LETTER. PREFERRENTIAL /IMMEDIATE CLEARANCE(WITHIN 05 MIN) TO BE GIVEN BY SHIPYARD BY VERBAL INTIMATION /EMAIL/LETTER FROMN SHIP OR PROJECT MONITORING TEAM |
| 1589 | ALL SHIPYARD WORKERS/SUBCONTRACTORS ETC TO BE CHECKED/SCANNED PRIOR ENTRY ONBOARD THE SHIP AND ALSO ALL ITEMS/BAGS TO BE X-RAYED. |
| 1590 | CCTV RECORD (WITH NIGHT VISION) OF THE ENTIRE SHIP'S PERIMETER TO BE KEPT FOR LAST THIRTY DAYS |
| 1591 | PROVIDE QA COVERAGE FOR ENTIRE WORK PACKAGE BY A REGISTERED THIRD PARTY INSPECTING AGENCIES EX - LRS, IRS, ABS ETC. |
| 1592 | SHIPYARD TO SUBMIT QAP AND QIP WITH IN 2 WEEKS OF SIGNING OF CONTRACT |
| 1593 | A DETAILED PERT /GANTT CHART TO BE SUMITTED TO NSRY AND SHIP (IN HARD AND SOFT MEDIA) ON TWO WEEKS PRIOR COMMENCEMENT OF REFIT. THE PERT/GANT CHART TO BE UPDATED TWICE EVERY MONTH AS PER THE PROGRESS OF REFIT. |
| 1594 | ONLINE MONITORING OF REFIT AND PERT CARDINALS TO BE ENABLED WITH MS PROJECT AND PRIMAVERA WITH SHIPYARD REPS, NSRY(K) REPS AND SHIP STAFF AS USERS |
| 1595 | PROVISION OF SHORE POWER 3 PHASE, 415V, 50HZ, FOR 30 DAYS IN DRY DOCK & FOR THE DURATION OF STAY FOR COMPLETE REFIT INCLUDING NECESSARY CONNECTION / DISCONNECTION (RATES AS PER ACTUAL READING ON BOARD/ENERGY METER READING INSTALLED BY SHIPYARD) POWER SUPPLY CABLE AND METER TO BE PROVIDED BY SHIPYARD. QUOTE FOR 1000 KWH/DAY. PAYMENT BASED ON THE ACTUAL DAYS AS PER WCC ON NOT EXCEEDING BASIS. SHIPYARDS TO INSTALL POWER METER . SHIP SHOULD BE EARTHED AT 04POINTS WHILE IN DRY DOCK. EARTHING CABLE TO BE SUPPLIED BY SHIPYARD. PROPER EARTHING AND ELECTRICAL SAFETY TO BE ENSURED |
| 1596 | PROVIDE 03 SEA WATER FIRE MAINS WITH 08 BAR PRESSURE FOR ENTIRE DURATION WITH CONTROL VALVES, MANIFOLDS AND INCLUDE NECESSARY CONNECTION / DISCONNECTION. SHIPYARD TO CONNECT REFERENCE PRESSURE GAUGE AT ALL MANIFOLDS DISCHARGE LINE. CALIBERATION CERTIFICATE OF PRESSURE GAUGES TO BE SUBMITTED ON COMMENCEMENT OF REFIT. PAYMENT BASED ON THE ACTUAL DAYS AS PER WCC ON NOT EXCEEDING BASIS. |
| 1597 | SHIPYARD TO PROVIDE 02 PORTABLE AC UNITS (TOTAL 80 TR CAPACITY) WITH AIR HOSES AND VENT PIPES TO SHIP DURING THE PERIOD OF WHARFAGE AND DRY DOCKING. ADEQUATE FLEXIBLE HOSES (MINIMUM)TO CARRY CHILLED AIR FROM PORTABLE AC UNITS TO ACCOMODATION AREAS, IN SHIP'S SUPERSTRUCTURE AND BELOW DECKS AND ELECTRONICS/ CONTROLS/ SENSOR COMPARTMENTS OF THE SHIP TO BE CATERED BY SHIP YARD. PAYMENT BASED ON THE ACTUAL DAYS AS PER WCC ON NOT EXCEEDING BASIS. RIGGING OF REQUIRED HOSES WIL BE RESPONSIBILITY OF THE SHIPYARD |
| 1598 | PROVIDE FRESH WATER 04 TONS PER DAY. PAYMENT BASED ON THE ACTUAL DAYS AS PER WCC ON NOT EXCEEDING BASIS. QUOTE TO INCLUDE NECESSARY CONNECTION / DISCONNECTION |
| 1599 | PROVIDE FACILITIES FOR GARBAGE COLLECTION AND DISPOSAL ARRANGEMENTS (15 KG EACH) TWICE PER DAY FROM SHIP PAYMENT BASED ON THE ACTUAL DAYS AS PER WCC ON NOT EXCEEDING BASIS. |
| 1600 | FOLLOWING TO BE PROVIDED:-PROVIDE CRANE 10-15 TON CAPACITY DURING THE REFIT (FOR NAVY'S REQUIREMENT ONLY. SHIPYARD REQUIREMENTS ARE TO BE CATERED IN SEPERATELY). PAYMENT BASED ON THE ACTUAL DAYS AS PER WCC ON NOT EXCEEDING BASIS. |
| 1601 | PROVIDE SERVICES OF ONE LISTERS DURING THE REFIT (FOR NAVY'S REQUIREMENT ONLY. SHIPYARD REQUIREMENTS ARE TO BE CATERED IN SEPERATELY). PAYMENT BASED ON THE ACTUAL HOURS AS PER WCC ON NOT EXCEEDING BASIS. |
| 1602 | PROVIDE SERVICES OF ONE FORK-LIFT DURING THE REFIT (FOR NAVY'S REQUIREMENT ONLY. SHIPYARD REQUIREMENTS ARE TO BE CATERED IN SEPERATELY). PAYMENT BASED ON THE ACTUAL HOURS AS PER WCC ON NOT EXCEEDING BASIS. |
| 1603 | PROVIDE MOBILE CRANE 40 TON CAPACITY DURING THE REFIT (FOR NAVY'S REQUIREMENT ONLY). PAYMENT BASED ON THE ACTUAL HOURS AS PER WCC ON NOT EXCEEDING BASIS. |
| 1604 | SHIPYARD TO ARRANGE FOR DEFUELLING OF SHIP PRIOR TO COMMENCEMENT OF REFIT. (Details of the tank will be provided later) |
| 1605 | CLEANING OF ALL TANKS, VENTILLATION AND OBTAINING GAS FREE CERTIFICATE IS THE RESPONSIBILITY OF SHIPYARD. SHIPYARD TO PROVIDE FACILITY TO DUMP DIRTY FUEL, SLUDGE AND LUB OIL. PAYMENT BASED ON THE ACTUALS AS PER WCC ON NOT EXCEEDING BASIS. |
| 1606 | SHIPYARD HAS TO STORE THE DEFUELLED LSHFHSD AND AFCAT IN SUITABLE PLACE AND REFUEL THE SAME BACK TO SHIP AT END OF REFIT AFTER GETTING SERVICEABLE CERTIFICATE FROM IOCL. CATER FOR FRESH FUEL INCASE DEFUELLED LSHFHDS/ AVCAT GOT CONTAMINATED (Details of the tank will be provided later) |
| 1607 | PROVIDE 15 FIRE FIGHTING TRAINED HOT WORK SENTRIES WITH 02 SUPERVISORS FOR 16 HRS EACH DAY FOR THE DURATION OF REFIT. NUMBER OF SENTRIES REQUIRED WILL BE INTIMATED BASED ON SHIP YARD'S REQUISITION FOR HOT WORK RECEIVED THE PREVIOUS DAY. PAYMENT BASED ON THE ACTUAL DAYS AS PER WCC ON NOT EXCEEDING BASIS. |
| 1608 | PROVISIONING OF 10 SEMI-SKILLED SAFETY SENTRIES TO ENSURE SAFETY AND HOUSE KEEPING DURINGTHE FOLLOWING EVOLUTIONS AND FOR UNDERTAKING TIMELY OPERATIONALISION AND TRIALS OF ALL EQUIPMENT ON COMPLETION OF ROUTINES/REPEIR:-(I) FOR MANNING THE SHIP TO CHECK FOR LEAKAGE/FOODING AT VARIOUS LOCATIONS DURING TRIALS OF FIRE MAIN,DRENCHER,SPRINKLER AND OTHER FIRE-FIGHTING SYSTEM CHECKS AS A PART OF PRE-REFIT AND POST REFIT TRIALS.(II) DURING TRANSFER OF LUB OIL AND FUEL IN SYSTEM TANKS AND EQUIPMENT FROM JETTY.(III) FOR MANNING VARIOUS COMPARTMENTS DURING HARBOUR TRIALS OF EQUIPMENT AND MAJOR FIRE FIGHTING EQUIPMENT.(IV) FITMENT OF BILGE PLATES IN UNDERWATER COMPARTMENTS AND SAFETY GUARDS OF ALL EQUIPMENT.(V) TORQUE TIGHTNESS CHECKS OF SYSTEM PIPES AND FLANGES THROUGHOUT THE SHIP PRIOR TO COMMISSIONING OF EACH SYSTEM TO PREVENT LEAKAGES. PAYMENT BASED ON THE ACTUAL DAYS AS PER WCC ON NOT EXCEEDING BASIS. |
| 1609 | TEMPORARY LIGHTING AND VENTILLATION ONBOARD FOR THE ENTIRE DURATION OF REFIT TO BE PROVIDED IN ALL MACHINERY COMPARTMENTS, COMPARTMENTS WITHIN SUPERSTRUCTURE, ALL ALLEYWAYS/ PASSAGE WAYS, CARGO SPACE, BALLAST TANKS MUST BE WELL LIT WITH 24 VDC LAMPS. PROVISION OF MAXIMUM 20 LIGHT POINTS PER DAY. PAYMENT BASED ON THE ACTUAL DAYS AS PER WCC ON NOT EXCEEDING BASIS. |
| 1610 | PROVIDE LOAD BANK 500 KW FOR LOAD TRIALS OF DAS WITH M-LOAD TRIALS CAPACITY INCLUDING HIRE CHARGES WITH OPERATOR CREW AND NECESSARY CONNECTION/SHIFTING. (FOR NAVY'S ADDITIONAL REQUIREMENT,IF ANY ONLY. SHIPYARD REQUIREMENTS VIZ. MANDATORY TRIALS POST ROUTINES ARE TO BE CATERED IN SEPERATELY). PAYMENT BASED ON THE ACTUAL DAYS AS PER WCC ON NOT EXCEEDING BASIS. |
| 1611 | PROVIDE PORTABLE 250 KW DA INCLUDING HIRE CHARGES WITH OPERATOR CREW AND NECESSARY CONNECTION/SHIFTING. (FOR NAVY'S ADDITIONAL REQUIREMENT,IF ANY ONLY. SHIPYARD REQUIREMENTS VIZ. DA REQUIREMENT VIEW NON AVAILABILITY OF SHORE SUPPLY TO BE CATERED SEPERATELY). PAYMENT BASED ON THE ACTUAL DAYS AS PER WCC ON NOT EXCEEDING BASIS. |
| 1612 | 15 NOS PORTABLE VENTILATION BLOWERS NEED TO BE SUPPLIED FOR THE DURATION OF REFIT FOR VENTILATION OF THE COMPARTMENTS AND TANKS (FOR NAVY'S REQUIREMENT ONLY. SHIPYARD REQUIREMENTS ARE TO BE CATERED IN SEPERATELY) PAYMENT BASED ON THE ACTUAL DAYS AS PER WCC ON NOT EXCEEDING BASIS. |
| 1613 | 02 NOS LP AIR COMPRESSOR NEED TO BE SUPPLIED FOR THE DURATION OF REFIT FOR LP AIR SUPPLY. (FOR NAVY'S REQUIREMENT ONLY. SHIPYARD REQUIREMENTS ARE TO BE CATERED IN SEPERATELY). PAYMENT BASED ON THE ACTUAL DAYS AS PER WCC ON NOT EXCEEDING BASIS. |
| 1614 | PROVIDE CARRY AWAY PIPES (4 INCH DIA, 10 NOS) . FIXING AND REMOVAL OF CARRY AWAY PIPES TO BE CATERED BY SHIPYARD. PAYMENT AT ACTUALS, BASED ON THE QUANTITY MENTIONED IN THE WORK COMPLETION CERTIFICATE ON NOT EXCEEDING BASIS. PAYMENT BASED ON THE ACTUAL DAYS AS PER WCC ON NOT EXCEEDING BASIS. |
| 1615 | SHIPYARD TO ENSURE MOVEMENT OF STEEL FROM MO (KOC) / NSRY (KOC) TO SHIPYARD INCLUDING LOADING / UNLOADING, MANPOWER (04 MEN), TRAILOR, MOBILE CRANE (02 NOS, 5 TONNE EACH), FORK LIFT AND OTHER REQUIRED ACCESSORIES. PAYMENT BASED ON THE ACTUAL DAYS AS PER WCC ON NOT EXCEEDING BASIS. |
| 1616 | ANALYSIS OF LUB OIL, COOLENT, HYDRAULIC OIL AND POTABLE WATER. (all Main Engines, Diesel Alternators, Gear Boxes and Auxilary machineries) TO BE CARRIED THROUGH NABL CERTIFIED LABORATRY AND TWO COPIES OF THE EACH REPORT TO BE SUBMITTED WITHIN 24 HOURS OF TEST UNDERTAKEN. SHIPYARD TO MAKE ARRANGEMENT FOR AVAILABILITY OF PORTABLE TESTING FACILITY WITHIN SHIPYARD PREMISES TO ADVANCE THE TIMELINES. PAYMENT BASED ON THE ACTUALS AS PER WCC ON NOT EXCEEDING BASIS. |
| 1617 | (1) LUB OIL TEST(1.1) BASIC TEST:- THE BASIC TEST OF LUB OIL SHOULD COVERS THE FOLLOWING:-(1.1.1) BY USING METHOD OF ASTM D445 :- (1.1.1.1) VISCOSITY @ 40 DEGREE C (CST) (1.1.1.2) VISCOSITY @ 100 DEGREE C (CST) (1.1.1.3) VISCOSITY INDEX (CALCUATED)(1.1.2) WATER CONTENT (% VOL) BY ASTM D95 METHOD. (1.1.3) FLASH POINT ( DEGREE CENTIGRADE) BY ASTM D92 METHOD (1.1.4) TBN (MG KOH/G)) BY ASTM D644 METHOD(1.1.5) TAN (MG KOH/G)) BY ASTM D644 METHODPAYMENT BASED ON THE ACTUALS AS PER WCC ON NOT EXCEEDING BASIS. |
| 1618 | (1.2) ADVANCE TEST :- THE ADVANCE TEST OF LUB OIL SHOULD COVERS THE FOLLOWING BY USING ASTM D5185 METHOD:- (1.1.1) WEAR METALIC PARTICALS OF FE, CR, NI, AL, CU, SN, PB AND AG TO BE ANALISED IN TERMS OF PPM IN THE GIVEN SAMPLES OF LUB OIL. (1.1.2) CONTAMINANTS OF SI, NA AND MG TO BE ANALISED IN TERMS OF PPM IN THE GIVEN SAMPLES OF LUB OIL. PAYMENT BASED ON THE ACTUALS AS PER WCC ON NOT EXCEEDING BASIS. |
| 1619 | (2)COOLANT TEST / FRESH WATER ADDITIVE TEST - THE FOLLOWING PARAMETERS TO BE ANALYSIS FOR GIVEN SAMPLE: -(2.1) PH VALUE (2.2) CHLORIDE CONTENT (2.3) PERCENTAGE OF INHIBITOR (2.4) HARDNESS (2.5) ANY OTHER TEST REQUIRED. PAYMENT BASED ON THE ACTUALS AS PER WCC ON NOT EXCEEDING BASIS. |
| 1620 | (3) POTABLE WATER - TEST TO BE CARRIED OUT TO ACERTAIN THE SUITABLITY FOR DRINKING WATER. PAYMENT BASED ON THE ACTUALS AS PER WCC ON NOT EXCEEDING BASIS. |
| 1621 | (4) HYDRAULIC TEST:-(4.1) BASIC TEST SHOULD COVERS THE FOLLOWING:- (4.1.1) VISCOSITY @ 20% IN TERMS OF CST BY USING METHOD OF ASTM D445(4.1.2) VISCOSITY @ 50% IN TERMS OF CST BY USING METHOD OF ASTM D446(4.1.3) VISCOSITY INDEX RESULTS BY CALICULATIONS BY USING METHOD OF ASTM D447(4.1.4) TESTING BY VISUAL / APPREARANCE(4.1.5) WATER CONTENT TEST BY CRACKLE (4.1.6) WATER CONTENT TEST IN TERMS % VOL BY USING METHOD OF ASTM D95(4.1.7) PENTANE INSOLUBLE TEST IN TERMS OF % WT BY USING METHOD OF ASTM D893(4.1.8) TOLUENE INSOLUBLE TEST IN TERMS OF % WT BY USING METHOD OF ASTM D893(4.1.9) TAN TEST IN TERMS OF MG KOH/G BY USING METHOD OF ASTM D644(4.1.10) SALT CONTENT TEST IN TERMS OF PPM BY USING METHOD OF IP 77(4.1.11) FLASH POINT TEST IN TERMS OF DEGREE CENTIGRADE BY USING METHOD OF ASTM D92/ 93. PAYMENT BASED ON THE ACTUALS AS PER WCC ON NOT EXCEEDING BASIS. |
| 1622 | (4.2) HYDRAULIC ADVANCE TEST SHOULD BE CARRIED OUT TO FIND OUT THE MEASUREMENT OF CONTAMINATION (SIZE OF QUANTITY OF MECHANICAL IMPURITIES) BY USING THE METHOD OF DEFSTAN 5-56/ ISSUE 2 (1982) TO MEET THE ISO 11500. PAYMENT BASED ON THE ACTUALS AS PER WCC ON NOT EXCEEDING BASIS. |
| 1623 | (4.3) PROVISION OF CONTAINERS/ SAMPLE BOTTLES:- STANDARD CONTAINERS/ SAMPLE BOTTLES (CAPACITY OF 250 ML) TO BE PROVIDED BY SHIPYARDS FOR LANDING THE SAMPLES OF LUB OILS, COOLANTS, HYDRAULIC OILS ETC FOR ANALYSIS. PAYMENT BASED ON THE ACTUALS AS PER WCC ON NOT EXCEEDING BASIS. |
| 1624 | PUMPING OUT AND CLEANING OF BILGES TO BE UNDERTAKEN TO ENSURE SAFE WORKING CONDITION ONBOARD. AREA- 800 SQMTR. PAYMENT BASED ON THE ACTUALS AS PER WCC ON NOT EXCEEDING BASIS. |
| 1625 | COMPRESSION TESTING FOLLOWED BY GROUPING OF VIBRATION MOUNTS, REPLACE/ROUTINES TO BE CARRIED OUT FOR ALL MOUNTS BEING REPLACED, AS PER NAVAL STANDARDS |
| 1626 | ADMIN SERVICES |
| 1627 | SEPARATE SHORE TOILETS AND WASHROOMS FOR SHIP'S OFFICERS AND CREW SUITABLE FOR 20 OFFICERS AND 150 SAILORS NEAR TO SHIPS BERTH / DOCK (WITHIN 100 MTRS). PAYMENT BASED ON THE ACTUAL DAYS AS PER WCC ON NOT EXCEEDING BASIS. |
| 1628 | 01 AC DINING HALL WITH LEATHER SOFA SET, DINING TABLE TV WITH DTH CONNECTION,MUSIC SYSTEM AND ADEQUATE CUTLERY AND CHAIRS, CLOSE TO CO'S OFFICE. DINING OF 20 OFFICERS AT A TIME NEAR SHIPS BERTH (WITHIN 200 MTRS). PAYMENT BASED ON THE ACTUAL DAYS AS PER WCC ON NOT EXCEEDING BASIS. |
| 1629 | 01 AC DINING HALL SUITABLE FOR DINING TABLE AND CHAIRS FOR DINING OF 70 JUNIOR SAILORS AT A TIME NEAR SHIPS BERTH (WITHIN 200 MTRS). PAYMENT BASED ON THE ACTUAL DAYS AS PER WCC ON NOT EXCEEDING BASIS. |
| 1630 | 01 AC DINING HALL SUITABLE FOR DINING TABLE AND CHAIRS FOR DINING OF 30 SENIOR SAILORS AT A TIME NEAR SHIPS BERTH (WITHIN 200 MTRS). PAYMENT BASED ON THE ACTUAL DAYS AS PER WCC ON NOT EXCEEDING BASIS. |
| 1631 | PROVISION OF SHORE GALLEY WITH 04 LPG BURNERS/ELECTRIC HOT PLATES, INCLUDING COST OF GAS/ELECTRICITY AND SINK WITH WATER CONNECTION FOR WASHING OF PLATES, UTENSILS ETC. FRESH WATER RO PURIFIER/ HEAVY DUTY AQUAGUARD TO BE FITTED FOR MEETING GALLEY AND SHIPS CREW WATER REQUIREMENT (AT TWO LOCATIONS VIZ GALLEY AND DINING HALL). PAYMENT BASED ON THE ACTUAL DAYS AS PER WCC ON NOT EXCEEDING BASIS |
| 1632 | ONE DEEP FREEZER MAINTAINED AT TEMPERATURE (1-3°C) AND ANOTHER AT (-10°C), IF REQUIRED. PAYMENT BASED ON THE ACTUAL DAYS AS PER WCC ON NOT EXCEEDING BASIS |
| 1633 | AIR CONDITIONED SPACE FOR STOWAGE OF FRESH RATION. ( 12 FEET X 12 FFET). PAYMENT BASED ON THE ACTUAL DAYS AS PER WCC ON NOT EXCEEDING BASIS |
| 1634 | AIR CONDITIONED SPACE FOR STOWAGE OF DRY RATION. ( 12 FEET X 12 FFET). PAYMENT BASED ON THE ACTUAL DAYS AS PER WCC ON NOT EXCEEDING BASIS |
| 1635 | PROVISION OF 06 NOS 40 FT CONTAINERS FOR STOWAGE OF DEGUTTED ITEMS DURING NR. PAYMENT BASED ON THE ACTUAL DAYS AS PER WCC ON NOT EXCEEDING BASIS |
| 1636 | SUPPLY 300 LITRES OF DRINKING WATER (AQUAFINA/ KINLEY/ BISLERY) PER DAY ONBOARD SHIP AND OFFICE SPACES. PAYMENT BASED ON THE ACTUAL DAYS AS PER WCC ON NOT EXCEEDING BASIS |
| 1637 | WATER CONNECTION, HEAVY DUTY WASHING MACHINE, DRIER AND DRYING AREA FOR SHIP'S DHOBI FOR REFIT DURATION. PAYMENT BASED ON THE ACTUAL DAYS AS PER WCC ON NOT EXCEEDING BASIS |
| 1638 | DEDICATED PARKING AREA NEAR REFIT OFFICE FOR 120 PERSONNEL |
| 1639 | AIR CONDITIONED & FULLY FURNISHED OFFICE SPACE FOR CO (INCLUDING OFFICE TABLE, EXECUTIVE CHAIR, VISITORS SOFA, TV WITH DTH, FIRMLY MOUNTED GODREJ SAFE, 01 STRONG LOCKER AND 03 VISITORS CHAIRS AND DINNING TABLE WITH CHAIR) WITH ATTACHED TOILET AND WASHROOM FOR COMMANDING OFFICER FOR REFIT DURATION. PAYMENT BASED ON THE ACTUAL DAYS AS PER WCC ON NOT EXCEEDING BASIS |
| 1640 | AIR CONDITIONED & FULLY FURNISHED OFFICE SPACE (03 ROOMS/CONTAINERS) FOR OFFICERS, 05 EXECUTIVE CHAIR, AND 10 VISITORS CHAIRS FOR REFIT DURATION. PAYMENT BASED ON THE ACTUAL DAYS AS PER WCC ON NOT EXCEEDING BASIS |
| 1641 | AC OFFICE SPACE FOR REFIT OFFICE (ROOMS(06)/ CONTAINERS (06) FOR OFFICES VIZ, ENGG OFFICE, ELE OFFICE, HULL OFFICE, GUNNERY/SS OFFICE, SHIPS/REG OFFICE AND REFIT OFFICE, SIX TABLES, 20 CHAIRS AND 08 RACKS WITH LOCK FOR FILE KEEPING ARE TO BE PROVIDED FOR REFIT DURATION. PAYMENT BASED ON THE ACTUAL DAYS AS PER WCC ON NOT EXCEEDING BASIS |
| 1642 | PROVIDE 01 AC OFFICE SPACE / CONTAINER WITH REFRIGERATOR FOR SHIP'S SICK BAY FOR REFIT DURATION INCLUDING BEDS, TABLES AND STORAGE CUPBOARDS (TWO EACH). CLEARNCE OF MEDICAL WASTE ON DAILY BASIS. PAYMENT BASED ON THE ACTUAL DAYS AS PER WCC ON NOT EXCEEDING BASIS |
| 1643 | STATIONARY IS TO BE PROVIDED FOR SMOOTH FUNCTIONING OF SHIPS OFFICE FOR RS 25,000/- PER MONTH. PAYMENT BASED ON THE ACTUALS AS PER WCC ON NOT EXCEEDING BASIS |
| 1644 | 40 INCH TVs WITH DTH CONNECTION AT 04 SEPARATE LOCATIONS ARE TO BE PROVIDED DURING REFIT PERIOD. PAYMENT BASED ON THE ACTUAL DAYS AS PER WCC ON NOT EXCEEDING BASIS |
| 1645 | ALL PCS/PERIPHERALS IN OFFICE SPACES TO BE SETUP IN LAN CONFIGURATION AS INDICATED BY SHIP STAFF. PAYMENT BASED ON THE ACTUAL DAYS AS PER WCC ON NOT EXCEEDING BASIS |
| 1646 | ONE OFFICE ASSISTANT/CLEANING STAFF FOR DAILY MAINTENANCE TO BE AVAILABLE 12 HRS IN A DAY FOR REFIT DURATION. PAYMENT BASED ON THE ACTUAL DAYS AS PER WCC ON NOT EXCEEDING BASIS |
| 1647 | PROVIDE 02 NO 40 FT CONTAINERS/LAY-APART STORE FOR STOWAGE AND PRESERVATION OF SPARES/ ITEMS DURING REFIT TIME. PAYMENT BASED ON THE ACTUAL DAYS AS PER WCC ON NOT EXCEEDING BASIS |
| 1648 | PROVIDE AC 01 CONTAINERS/LAY-APART STORE FOR STOWAGE AND PRESERVATION OF CRITICAL SPARES / ITEMS DURING REFIT TIME. PAYMENT BASED ON THE ACTUAL DAYS AS PER WCC ON NOT EXCEEDING BASIS |
| 1649 | PROVIDE TWO SEPARATE AC PORTABLE CABINS FOR OOD AND DUTY WATCH DURING NIGHT ADJACENT TO SHIP IN JETTY FOR THE FULL REFIT DURATION. PAYMENT BASED ON THE ACTUAL DAYS AS PER WCC ON NOT EXCEEDING BASIS |
| 1650 | SHIPYARD TO PROVIDE FULLY EQUIPED AMBULANCE ON SHORT NOTICE.PAYMENT BASED ON THE ACTUAL DAYS AS PER WCC ON NOT EXCEEDING BASIS |
| 1651 | SULLAGE BARGE (100 TONS CAPACITY) TO BE PROVIDED ON THREE OCCASIONS. ONCE PRIOR COMMENCEMENT OF REFIT, ONCE AFTER UNDOCKING AND ONCE AFTER TRIALS. PAYMENT AT ACTUALS. |
| 1652 | PROVIDE CASUAL LABOURS TO UNDERTAKE BILGE CLEANSHIP DURING TRIAL PHASE OF REFIT. NO OF PERSONNEL - 08. DURATION - 45 DAYS. PAYMENT AS PER ACUTAL MAN DAYS UTILISED. |
| 1653 | (A) PROVIDE FULLY FURNISHED OFFICE SPACE( 400 SQFT) FOR OI/C PROJECT MONITORING TEAM OF NSRY(KOC) WITH TWO ACs, WORK STATION, LOCKERS, STORAGE, ATTACHED TOILET, WASHROOM, CHANGING ROOM, LAND LINE TELEPHONE WITH STD AND 01 BROAD BAND CONNECTION AND TV (44 INCH ATLEAST WITH DISH CONNECTION). PAYMENT BASED ON THE ACTUAL DAYS AS PER WCC ON NOT EXCEEDING BASIS |
| 1654 | (B) PROVIDE FULLY FURNISHED OFFICE SPACE( 400 SQFT) FOR STAFF OF RMT(NSRY(KOC) WITH TWO ACs, FOUR WORK STATIONS, FOUR LOCKERS AND STORAGE, ATTACHED TOILET, WASHROOM, CHANGING ROOM, LAND LINE TELEPHONE WITH STD AND 01 BROAD BAND CONNECTION AND TV (MINIMUM 42 INCH ATLEAST WITH DISH CONNECTION). PAYMENT BASED ON THE ACTUAL DAYS AS PER WCC ON NOT EXCEEDING BASIS |
| 1655 | (C) ONE FULLY FURNISHED AC OFFICE SPACE FOR FIVE(05) SAILORS OF THE PROJECT MONITORING TEAM WITH FIVE(05) INDIVIDUAL WORKSTATIONS, STORAGE AND LOCKERS, ATTACHED TOILET, WASHROOM, CHANGING ROOM AND LAND LINE TELEPHONE WITH STD AND 01 BROAD BAND CONNECTION. P ALL OFFICE STATIONARY ITEMS / SUPPLIES AS REQUIRED, FOR THE ENTIRE DURATION OF THE REFIT IS TO BE PROVIDED. (ALL PCS / PERIPHERALS TO BE SET UP IN LAN CONFIGURATION, AS AND WHERE REQUIRED BY COA). PAYMENT BASED ON THE ACTUAL DAYS AS PER WCC ON NOT EXCEEDING BASIS |
| 1656 | ONE OFFICE ASSISTANT/CLEANING STAFF FOR DAILY MAINTENANCE TO BE AVAILABLE 12 HRS IN A DAY FOR REFIT DURATION. PAYMENT BASED ON THE ACTUAL DAYS AS PER WCC ON NOT EXCEEDING BASIS |
| 1657 | STATIONARY, AS INDICATED BY RMT, IS TO BE PROVIDED FOR SMOOTH FUNCTIONING OF RMT(PLANNING & COMMERCIAL) OFFICE OF NSRY FOR Rs 35,000/- PER MONTH. PAYMENT BASED ON THE ACTUALS AS PER WCC ON NOT EXCEEDING BASIS |
| 1658 | FOLLOWING TO BE ENSURED FOR ALL ABOVE OFFICE SPACES (A) DRINKING WATER THROUGH RO/AQUAGAUARD WITHIN 50 M (B) SEPARATE TOILETS FOR OFFICERS AND CREW ARE TO BE PROVIDED WITHIN 50M (C) DAILY MAINTENANCE / CLEANING. PAYMENT BASED ON THE ACTUALS AS PER WCC ON NOT EXCEEDING BASIS |
| 1659 | PROVIDE ONE CHANGING ROOM WITH LOCKERS AND ATTACHED WASH ROOM FOR 10 NSRY(K) WORKERS. PAYMENT BASED ON THE ACTUAL DAYS AS PER WCC ON NOT EXCEEDING BASIS. |
| 1660 | PROVIDE 04 DATA ENTRY OPERATORS WITH 1-2 YEARS EXPERIENCE HAVING ADEQUATE COMPUTER KNOWLEDGE AND EXPERIENCE IN MS PROJECT, OFFICE(PPT, WORD, EXCEL, ETC). (ADDITIONAL DAYS INCLUDED FOR PRE-REFIT AND POST-REFIT ACTIVITIES) FOR PLANNING (02 NOS) & COMMERCIAL (02 NOS) DEPARTMENT OF NSRY. SHIPYARD TO PROVIDE A PROOF OF MINIMUM WAGES OF RS 1465/- PER DAY (EXCLUDING EPF AND ESI CONTRIBUTION OF EMPOLYEE & EMPLOYER) PAID TO THE REFIT DATA ENTRY OPERATORS. PAYMENT BASED ON THE ACTUAL DAYS AS PER WCC ON NOT EXCEEDING BASIS. |
| 1661 | 01 OFFICE ASSISTANCE TO BE PROVIDED TO PROJECT MONITORING TEAM/ OFFICE FOR MOVEMENT OF DOCUMENTS/REPORTS. POEN / OFFICE ASSISTANCE IS REQUIRED TO VISIT ONBOARD SHIP AND LOCATIONS (AS REQUIRED) FOR MOVEMENT OF FILES /OTHER ASSISTANCES ROUND THE CLOCK ON SHIFT BASIS. SHIPYARD TO PROVIDE A PROOF OF MINIMUM WAGES OF RS 1250/- PER DAY (EXCLUDING EPF AND ESI CONTRIBUTION OF EMPOLYEE & EMPLOYER) PAID TO THE POEN / OFFICE ASSISTANCE. PAYMENT BASED ON THE ACTUAL DAYS AS PER WCC ON NOT EXCEEDING BASIS. |
| 1662 | PROVIDE 02 TECHNICAL SUPERVISIORS [RETIRED IN SAILORS (ERA/EAP) OR EACH WITH MINIMUM B.TECH WITH TWO YEARS EXPERIENCE IN SHIPYARD ] FOR PLANNING & COMMERCIAL DIVISION OF NSRY. (ADDITIONAL DAYS INCLUDED FOR PRE-REFIT AND POST-REFIT ACIVITIES). SALARY TO MATCH SHIPYARD ASSISTANT/ DEPUTY MANAGER LEVEL. (SHIPYARD TO PROVIDE A PROOF OF MINIMUM WAGES OF RS 2565/- PER DAY (EXCLUDING EPF AND ESI CONTRIBUTION OF EMPOLYEE & EMPLOYER) PAID TO THE REFIT COORDINATORS. PAYMENT BASED ON THE ACTUAL DAYS AS PER WCC ON NOT EXCEEDING BASIS. |
| 1663 | PROVIDE 02 REFIT COORDINATORS EACH WITH MINIMUM B.TECH WITH ATLEAST TWO YEAR EXPERIENCE. SALARY TO MATCH SHIPYARD ASSISTANT/ DEPUTY MANAGER LEVEL. (ADDITIONAL DAYS INCLUDED FOR PRE-REFIT AND POST-REFIT ACIVITIES) FOR RMT OF NSRY. PAYMENT AT ACTUALS.SHIPYARD TO PROVIDE A PROOF OF MINIMUM WAGES OF RS 2565/- PER DAY (EXCLUDING EPF AND ESI CONTRIBUTION OF EMPOLYEE & EMPLOYER) PAID TO THE REFIT COORDINATORS. PAYMENT BASED ON THE ACTUAL DAYS AS PER WCC ON NOT EXCEEDING BASIS. |
| 1664 | PROVIDE 03 ACCOUNTANTS CUM AUDITORS WITH ATLEAST BCOM DEGREE AND HAVING 2 YEARS EXPERIENCE IN ACCOUNTING AND AUDIT FOR HANDLING BILLS AND CONTRACTS FOR COMMERCIAL DEPARTMENT OF NSRY. (ADDITIONAL DAYS INCLUDED FOR PRE-REFIT AND POST-REFIT ACIVITIES) PAYMENT AT ACTUALS. SHIPYARD TO PROVIDE A PROOF OF MINIMUM WAGES OF RS 2198/- PER DAY (EXCLUDING EPF AND ESI CONTRIBUTION OF EMPOLYEE & EMPLOYER) PAID TO THE REFIT ACCOUNTANT-CUM-AUDITORS. PAYMENT BASED ON THE ACTUAL DAYS AS PER WCC ON NOT EXCEEDING BASIS. |
| 1665 | AC EXECUTIVE ROOM FOR CO WITH ATTACHED TOILET/BATHROOM DURING REFIT DURATION, (INCLUDING TV WITH DTH CONNECTION, CONSERVENCY, HOT WATER, HOUSE KEEPING, LAUNDRY SERVICES(08 PIECE PER DAY), MEALS (VEG/NON VEG 2 PER DAY), BEVERAGE(2 PER DAY)),IN HOTEL AS PER AS PER ENTITLEMENT. PAYMENT BASED ON THE ACTUAL DAYS AS PER WCC ON NOT EXCEEDING BASIS. |
| 1666 | AC EXECUTIVE ROOM FOR 04 HEADS OF DEPARTMENT WITH ATTACHED TOILET/BATHROOM DURING REFIT DURATION, (INCLUDING TV WITH DTH CONNECTION, CONSERVENCY, HOT WATER, HOUSE KEEPING, LAUNDRY SERVICES(08 PIECE PER DAY), MEALS (2 PER DAY), BEVERAGE(2 PER DAY)),IN HOTEL AS PER AS PER ENTITLEMENT. PAYMENT BASED ON THE ACTUAL DAYS AS PER WCC ON NOT EXCEEDING BASIS. |
| 1667 | AC SINGLE CABINS EACH FOR 13 OFFICERS WITH ATTACHED TOILETS AND BATHROOMS DURING REFIT DURATION (INCLUDING TV WITH DTH CONNECTION, CONSERVENCY, HOT WATER, HOUSE KEEPING, LAUNDRY SERVICES(08 PIECE PER DAY), MEALS (VEG/NON VEG 2 PER DAY), BEVERAGE(2 PER DAY)). IN HOTEL AS PER AS PER ENTITLEMENT. PAYMENT BASED ON THE ACTUAL DAYS AS PER WCC ON NOT EXCEEDING BASIS. |
| 1668 | AC ACCOMODATION FOR 40 SENIOR SAILORS ON TWIN SHARING BASIS (INCLUDING TV WITH DTH CONNECTION, CONSERVENCY, HOT WATER, HOUSE KEEPING, 08 PIECES OF LAUNDARY PER SAILOR PER DAY). IN HOTEL AS PER AS PER ENTITLEMENT. PAYMENT BASED ON THE ACTUAL DAYS AS PER WCC ON NOT EXCEEDING BASIS. |
| 1669 | AC ACCOMODATION/DORMATORY FOR 120 JUNIOR SAILORS. (INCLUDING TV WITH DTH CONNECTION, CONSERVENCY, HOT WATER, HOUSE KEEPING, LAUNDARY WITH AUTOMATIC WASHING MACHINES,DRYING AND IRONING FACILITY). ACCOMODATION AS PER AS PER ENTITLEMENT. PAYMENT BASED ON THE ACTUAL DAYS AS PER WCC ON NOT EXCEEDING BASIS. |
| 1670 | TWO ROOMS NEAR SAILORS ACCOMDATION FOR FUNCTIONING OF SHIP'S BARBER SHOP AND DOBHI. PAYMENT BASED ON THE ACTUAL DAYS AS PER WCC ON NOT EXCEEDING BASIS. |
| 1671 | TWO AC ACCOMODATION FOR STAFF OF RMT(NSRY) WITH ATTACHED TOILET/BATHROOM DURING REFIT DURATION, (INCLUDING TV WITH DTH CONNECTION, CONSERVENCY, HOT WATER, HOUSE KEEPING, LAUNDRY SERVICES(08 PIECE PER DAY PER STAFF), MEALS (VEG/NON VEG 03 PER DAY PER STAFF). HOTEL AS PER ENTITLEMENT. PAYMENT BASED ON THE ACTUAL DAYS AS PER WCC ON NOT EXCEEDING BASIS. |
| 1672 | TWO AC EXECUTIVE SUITE FOR OI/C RMT WITH ATTACHED TOILET/BATHROOM DURING REFIT DURATION, (INCLUDING TV WITH DTH CONNECTION, CONSERVENCY, HOT WATER, HOUSE KEEPING, LAUNDRY SERVICES(08 PIECE PER DAY PER OFFICER), MEALS (VEG/NON VEG 03 PER DAY PER OFFICER), BEVERAGE(2 PER DAY PER OFFICER)). HOTEL AS PER ENTITLEMENT. PAYMENT BASED ON THE ACTUAL DAYS AS PER WCC ON NOT EXCEEDING BASIS. |
| 1673 | TWO AC EXECUTIVE SUITE FOR REFIT REVIEWING OFFICERS DEPUTED BY COA WITH ATTACHED TOILET/BATHROOM DURING REFIT DURATION, (INCLUDING TV WITH DTH CONNECTION, CONSERVENCY, HOT WATER, HOUSE KEEPING, LAUNDRY SERVICES(08 PIECE PER DAY PER OFFICER), MEALS (VEG/NON VEG 03 PER DAY PER OFFICER), BEVERAGE(2 PER DAY PER OFFICER). PAYMENT BASED ON THE ACTUAL DAYS AS PER WCC ON NOT EXCEEDING BASIS. |
| 1674 | PROVIDE ONE TONNER TRUCK (WITH TRANSIT INSURANCE, PACKING AND LOADING) FOR TRANSPORTING SHIPS MATERIAL/SPARES FROM SHIPYARD TO MO(K)/NSRY(K) FOR 10 HRS/100 KMS PER DAY WHICHEVER IS LESS. REQUIREMENT FOR TRANSPORT WILL BE INTIMATED ONE DAY IN ADVANCE. PAYMENT BASED ON THE ACTUAL DAYS AS PER WCC ON NOT EXCEEDING BASIS. |
| 1675 | PROVIDE TWO FIVE SEATER AC CARS, ONE EACH FOR OI/C RMT AND COMMERCIAL SECTION (15 HRS/150 KMS PER DAY). (CAR REGISTRATION NOT TO BE OLDER THAN 2025, WHITE COLOUR, FITTED WHITE SEAT COVERS, SANITISATION DAILY, DRIVER TO BE WELL GROOMED AND MUST WEAR SHIRT, TROUSER AND SHOES WITH VALID POLICE CLEARANCE CERTIFICATE FOR DRIVERS). PAYMENT BASED ON THE ACTUAL DAYS AS PER WCC ON NOT EXCEEDING BASIS. |
| 1676 | PROVIDE ONE FIVE SEATER AC CAR FOR VISITING OFFICERS (NSRY) (15 HRS/150 KMS PER DAY) (CAR REGISTRATION NOT TO BE OLDER THAN 2025, WHITE COLOUR, FITTED WHITE SEAT COVERS, SANITISATION DAILY, DRIVER TO BE WELL GROOMED AND MUST WEAR SHIRT, TROUSER AND SHOES WITH VALID POLICE CLEARANCE CERTIFICATE FOR DRIVERS). PAYMENT BASED ON THE ACTUAL DAYS AS PER WCC ON NOT EXCEEDING BASIS. |
| 1677 | ONE 05 SEATER AC CAR FOR SHIPS CO (15 HRS/100 KMS PER DAY) (CAR REGISTRATION NOT TO BE OLDER THAN 2025, WHITE COLOUR, FITTED WHITE SEAT COVERS, SANITISATION DAILY, DRIVER TO BE WELL GROOMED AND MUST WEAR SHIRT, TROUSER AND SHOES WITH VALID POLICE CLEARANCE CERTIFICATE FOR DRIVERS). PAYMENT BASED ON THE ACTUAL DAYS AS PER WCC ON NOT EXCEEDING BASIS. |
| 1678 | TWO 05 SEATER AC CAR FOR SHIPS REFIT OFFICERS(15 HRS/100 KMS PER DAY) (CAR REGISTRATION NOT TO BE OLDER THAN 2025, WHITE COLOUR, FITTED WHITE SEAT COVERS, SANITISATION DAILY, DRIVER TO BE WELL GROOMED AND MUST WEAR SHIRT, TROUSER AND SHOES WITH VALID POLICE CLEARANCE CERTIFICATE FOR DRIVERS). PAYMENT BASED ON THE ACTUAL DAYS AS PER WCC ON NOT EXCEEDING BASIS. |
| 1679 | TWO AC BUS (52 SEATER) FOR SHIPS COMPANY. 15 HRS/150 KMS PER DAY). PAYMENT BASED ON THE ACTUAL DAYS AS PER WCC ON NOT EXCEEDING BASIS. |
| 1680 | PROVISION OF TWO MINI LORRY OF FOUR TONNE CAPACITY FOR TRANSPORTING SHIP'S MATERIALS/ITEMS/ SPARES.(15 HRS/150 KMS PER DAY). PAYMENT BASED ON THE ACTUAL DAYS AS PER WCC ON NOT EXCEEDING BASIS |
| 1681 | TWO BATTERY OPERATED TROLLEY FOR MAN / MATERIAL SHIFTING WITHIN THE SHIPYARD PREMISIS. PAYMENT BASED ON THE ACTUAL DAYS AS PER WCC ON NOT EXCEEDING BASIS |
| 1682 | PROVISIONING OF A TRAINED DEDICATED SOFTWARE OPERATOR (WITH A MINIMUM OF 03 YEARS EXPERIENCE) FOR UNDERTAKING REFIT MONITORING THROUGH REFIT MONITORING SOFTWARE (TO BE RPOVIDED BY THE SHIPYARD ALONG WITH ALL REQUISITE HARDWARE VIZ STANDALONE PC (QTY - 2), SERVER (QTY - 01), OFC (AS REQUIRED)), TO UNDERTAKE REAL TIME TRACKING OF REFIT ACTIVITIES / FOR MONITIORING FOR THE PERIOD OF REFIT. SOFTWARE SHOULD BE ABLE TO MONITOR THE REAL TIME PROGRESS OF REFIT IN A MULTIPLE REFIT ENVIRONMENT AND INDICATE CHANGES IN REFIT TIMELINES AS AS RESULT OF VARYING DYNAMICS IN REFIT VIZ. ALLOCATION OF PRODUCTION RESOURCES, MANPOWER, INCREASE IN SOW WARRANTING MORE MANDAYS AS AGAINST ORIGINALLY ENVISAGED ETC. THE REFIT MONITORING SOFTWARE ON COMPLETION OF REFIT, TO BE HANDED OVER TO COA. HARDWARE WILL BE RETURNED TO SHIPYARD POST DEGAUSSING BY IN TEAM ON COMPLETION OF DELIVERY PERIOD. THE FIRM TO RENDER AFTER SALES SERVICES UNDER WARRANTY CLAUSE FOR 01 YEAR POST EXPIRY OF DELIVERY PERIOD (PAYMENT AT ACTUALS). |
| 1683 | LIST OF SPARES TO BE QUOTED BY THE SHIPYARDS |
| 1684 | ENGINEERING |
| 1685 | Adjusting screw |
| 1686 | locking nut |
| 1687 | spring houseing |
| 1688 | seeling sleave |
| 1689 | cap nut |
| 1690 | pipe connection |
| 1691 | inlet connector |
| 1692 | retaiaing nut |
| 1693 | injector assembly |
| 1694 | o ring |
| 1695 | nozzle |
| 1696 | gasket |
| 1697 | washer |
| 1698 | gasket |
| 1699 | collar nut |
| 1700 | spindle assembly |
| 1701 | gasket |
| 1702 | cosalip (high temprature anti seize |
| 1703 | Fuel injection pump assemply complete |
| 1704 | split washer |
| 1705 | flange |
| 1706 | Push road follower |
| 1707 | O ring |
| 1708 | spring |
| 1709 | Push road |
| 1710 | Cam follower |
| 1711 | Circlip |
| 1712 | cam roller |
| 1713 | Screw |
| 1714 | Lock washer |
| 1715 | Shaft, cam roller |
| 1716 | Bushing |
| 1717 | Spacer |
| 1718 | Spacer |
| 1719 | pipe, inject .pump- inject valve (high pressure pipe ) |
| 1720 | pipe , inject. Pump- collect. pipe |
| 1721 | pipe, distrib. Pipe- inject pump |
| 1722 | pipe, fual drain |
| 1723 | pipe, drain oil cyl. Block- collector pipe |
| 1724 | flexiable fuel connections |
| 1725 | Hose clip |
| 1726 | Sealing sleeve |
| 1727 | Seal ring |
| 1728 | Cam follower |
| 1729 | Screw |
| 1730 | Locking plate |
| 1731 | cam roller |
| 1732 | Bushing |
| 1733 | Shaft |
| 1734 | Gasket |
| 1735 | Ball bearing |
| 1736 | Gasket |
| 1737 | Split pin |
| 1738 | Gear wheel |
| 1739 | Ball bearing |
| 1740 | Spacer |
| 1741 | Shaft gear Wheel ,governor drive |
| 1742 | Bevel gear wheel |
| 1743 | Beval gear wheel |
| 1744 | Circlip |
| 1745 | Ball bearing |
| 1746 | O ring |
| 1747 | Gasket governor 1,0 mm |
| 1748 | Gasket governor 0,75 mm |
| 1749 | Gasket governor 0,25 mm |
| 1750 | Gasket governor 0,15 mm |
| 1751 | Gasket governor 0,5 mm |
| 1752 | Coupling |
| 1753 | Coil spring |
| 1754 | Sealing ring |
| 1755 | springe-plate |
| 1756 | Spacer |
| 1757 | Circlip |
| 1758 | Circlip |
| 1759 | Gasket governor 1,0 mm |
| 1760 | Gasket governor 0,75 mm |
| 1761 | Gasket governor 0,5 mm |
| 1762 | Gasket governor 0,25 mm |
| 1763 | Gasket governor 0,15 mm |
| 1764 | Tapered guid pin |
| 1765 | pilot starting air distributor with drive overhaul kit |
| 1766 | Strainer |
| 1767 | Gasket |
| 1768 | Gasket |
| 1769 | Lube oil priming pump complete overhauling kit |
| 1770 | Gasket set for LO PHE |
| 1771 | O ring |
| 1772 | Strainer Element |
| 1773 | hose clamp |
| 1774 | Rubber sleeve |
| 1775 | hose clamp |
| 1776 | Rubber sleeve |
| 1777 | Copaslip |
| 1778 | Complete exhaust manifold parts (includng bellows )with fastners for KV -12 |
| 1779 | Gasket set for fresh water PHE |
| 1780 | cooling water pump overhaul kit (if engine driven ) |
| 1781 | Temperature and pressure gauges |
| 1782 | Sealing ledge, compl |
| 1783 | Sealing ledge, compl |
| 1784 | Sealing ledge, compl |
| 1785 | Gasket |
| 1786 | Gasket |
| 1787 | Circlip |
| 1788 | Cup, Rocker Arm- Exh Valve |
| 1789 | Allen Screw |
| 1790 | Inlet Valve |
| 1791 | Valve spring, inner |
| 1792 | Valve spring, outer |
| 1793 | spring retainer |
| 1794 | Impact Bolt |
| 1795 | slide Shoe |
| 1796 | Circlip |
| 1797 | Tapered seat lock |
| 1798 | Core hole cover |
| 1799 | Gasket, core hole cover |
| 1800 | Ring/Sleeve - injection valve |
| 1801 | Bushing / fuel oil valve- R 10/13 |
| 1802 | Sleeve , injection valve |
| 1803 | O Ring |
| 1804 | Adjusting screw rocker Arm |
| 1805 | Gasket |
| 1806 | Stud M 12x20, set screw |
| 1807 | Male stud |
| 1808 | Pipe, Lub oil bracket Roc Arms |
| 1809 | T-connector |
| 1810 | Nut, Adj , Screw rocker Arm |
| 1811 | Adjusting screw rocker Arm |
| 1812 | Chain |
| 1813 | Chain lock |
| 1814 | Roller bearing |
| 1815 | Circlip |
| 1816 | Big end bearing , Upper |
| 1817 | Big end bearing, Lower |
| 1818 | Piston ring set |
| 1819 | Circlip |
| 1820 | Main bearing shell, upper |
| 1821 | Main bearing shell, lower |
| 1822 | Thrust washer |
| 1823 | Banjo screw |
| 1824 | O ring kit Hydraulic tool (Main bearing) |
| 1825 | O ring kit Hydraulic tool (Con rod bearing) |
| 1826 | O ring kit Hydraulic tool (Cylinder head) |
| 1827 | o ring |
| 1828 | nozzle |
| 1829 | gasket |
| 1830 | washer |
| 1831 | gasket |
| 1832 | collar nut |
| 1833 | spindle assembly |
| 1834 | gasket |
| 1835 | cosalip (high temprature anti seize compound) |
| 1836 | spill plug( eriosen plug )& its washer |
| 1837 | Seal washer |
| 1838 | Seal washer |
| 1839 | eroisen plug |
| 1840 | copper gasket for fuel pump connection |
| 1841 | Filter- element |
| 1842 | Gasket kit |
| 1843 | Strainer |
| 1844 | Filter elementes |
| 1845 | Centrifugal filter overhauling kit + paper insert kit |
| 1846 | CA cooler gasket kit (Air side & water side) |
| 1847 | Anode set |
| 1848 | Gasket |
| 1849 | Gasket |
| 1850 | Gasket |
| 1851 | Gasket |
| 1852 | Gasket |
| 1853 | Gasket |
| 1854 | Gasket |
| 1855 | Gasket |
| 1856 | Gasket |
| 1857 | Sealing ring |
| 1858 | cylinder head overhauling kit |
| 1859 | O ring |
| 1860 | Gasket |
| 1861 | Gasket sealing frame cyl.Hea |
| 1862 | Circlip |
| 1863 | Lock ring valve spndle |
| 1864 | sleeve , outer |
| 1865 | hose clamp |
| 1866 | Gasket |
| 1867 | Hex lock nut |
| 1868 | Gasket |
| 1869 | Valve Seat |
| 1870 | Exhaust Valve Guide |
| 1871 | O ring |
| 1872 | Bushing , Bearing Bracket |
| 1873 | Disc, Rocker Arm, Exh, Valve |
| 1874 | Bushing , Bearing Bracket |
| 1875 | Disc, Rocker Arm sahft (washer) |
| 1876 | Circlip A 40 |
| 1877 | sahft, Rocker Arm, Inlet Valve |
| 1878 | Bushing Rocker Arm |
| 1879 | Valverator, K/L - Engine |
| 1880 | Exh. Valve |
| 1881 | O ring, Valve guide |
| 1882 | Inlet Valve guide |
| 1883 | Megaseal |
| 1884 | Molycote 55 m (big bottle) |
| 1885 | Molycote paste type p74,0,5 kg |
| 1886 | Copper Gasket for branch pipe, fuel oil to pump |
| 1887 | adjusting screw |
| 1888 | locking nut |
| 1889 | spring housing |
| 1890 | sealing sleeve |
| 1891 | cap nut |
| 1892 | pipe connection |
| 1893 | inlet connector |
| 1894 | retaining nut |
| 1895 | injector assembly |
| 1896 | Fuel injection pump assembly complete |
| 1897 | Split washer |
| 1898 | Control rod |
| 1899 | control sleeve |
| 1900 | Spring Plate Upper |
| 1901 | Circlip Upper |
| 1902 | Spring Plunger |
| 1903 | Plunger |
| 1904 | Plunger Cylinder |
| 1905 | Spring plate Lower |
| 1906 | tappet |
| 1907 | Circlip lower |
| 1908 | Relief Valve assembly |
| 1909 | Seal Washer |
| 1910 | O-ring |
| 1911 | O-ring |
| 1912 | Valve |
| 1913 | O-ring |
| 1914 | Gasket Kit |
| 1915 | Flange |
| 1916 | Spacer |
| 1917 | Spacer |
| 1918 | Pipe, inject.pump-inject.valve ( High pres5ure pipe) |
| 1919 | Pipe, inject.pump - collect. pipe |
| 1920 | Pipe, distrib.pipe - inject.pump |
| 1921 | Pipe, fuel drain |
| 1922 | Pipe. drain oil, cyl.block - collector |
| 1923 | Hose clip |
| 1924 | Sealing sleeve |
| 1925 | Seal ring |
| 1926 | Cam follower |
| 1927 | Screw |
| 1928 | Locking plate |
| 1929 | Cam roller |
| 1930 | Bushing |
| 1931 | Shaft |
| 1932 | Gasket |
| 1933 | Ball bearing |
| 1934 | Gasket |
| 1935 | Split pin |
| 1936 | Gear wheel |
| 1937 | Ball bearing |
| 1938 | Spacer |
| 1939 | Shaft gear wheel, governor drive |
| 1940 | Bevel gear wheel, governor drive |
| 1941 | Bevel gear wheel |
| 1942 | Circlip |
| 1943 | Ball bearing |
| 1944 | O-ring |
| 1945 | Gasket governor 1,0 mm |
| 1946 | Gasket governor 0,75 mm |
| 1947 | Gasket governor 0,25 mm |
| 1948 | Gasket governor 0.15 mm |
| 1949 | Gasket governor 0,5 mm |
| 1950 | Coupling |
| 1951 | Coil spring |
| 1952 | Sealing ring |
| 1953 | Springe-plate |
| 1954 | Spacer |
| 1955 | Circlip |
| 1956 | Circlip |
| 1957 | Gasket governor 1,0 mm |
| 1958 | Gasket governor 0, 75 mm |
| 1959 | Gasket governor 0,5 mm |
| 1960 | Gasket governor 0,25 mm |
| 1961 | Gasket governor 0, 15 mm |
| 1962 | Tapered guide pin |
| 1963 | Circlip |
| 1964 | Cross disc |
| 1965 | Spring |
| 1966 | Coupling |
| 1967 | Spring Sleeve pin |
| 1968 | Shaft |
| 1969 | Gasket (0.5 mm thickness) |
| 1970 | Gasket (1.0 mm thickness) |
| 1971 | Circlip |
| 1972 | Roller Bearing |
| 1973 | Start Air release valve |
| 1974 | Sealing Ring |
| 1975 | O ring |
| 1976 | Gasket |
| 1977 | Split Pin |
| 1978 | Castle Nut |
| 1979 | Taper roller bearing |
| 1980 | Sealing ring |
| 1981 | Washer |
| 1982 | Distributor valve |
| 1983 | Gasket |
| 1984 | Guide Pin |
| 1985 | Sheet Metal |
| 1986 | Strainer |
| 1987 | Gasket |
| 1988 | Gasket |
| 1989 | Lube oil priming pump complete overhauling kit |
| 1990 | Gasket set for LO PHE |
| 1991 | O-ring |
| 1992 | stariner element |
| 1993 | Hose Clamp |
| 1994 | Rubber sleeve |
| 1995 | Hose Clamp |
| 1996 | Rubber sleeve |
| 1997 | Copaslip |
| 1998 | Complete exhaust Manifold parts ( including bellows)with fastners for KV.12 |
| 1999 | Gasket set for fresh water PHE |
| 2000 | Temperature and pressure gauges |
| 2001 | Sealing ledge, compl |
| 2002 | Sealing ledge, compl |
| 2003 | Sealing ledge, compl |
| 2004 | Gasket |
| 2005 | Gasket |
| 2006 | Thrust washer |
| 2007 | Bearing shell |
| 2008 | Repair Kit Cooling Water Pump |
| 2009 | Gasket for water pipe |
| 2010 | Gasket water pump |
| 2011 | Gasket for water pipe |
| 2012 | Copper washer |
| 2013 | Shut off valve |
| 2014 | Copper washer |
| 2015 | Valve seat |
| 2016 | Spring retainer |
| 2017 | Distance sleeve |
| 2018 | Valve spring, inner |
| 2019 | valve spring , outer |
| 2020 | Spring retainer |
| 2021 | Allen Screw |
| 2022 | Impact Bolt |
| 2023 | Circlip |
| 2024 | Cup, Rocker Arm - Exh. Valve |
| 2025 | Core Hole Cover |
| 2026 | Gasket, Core Hole Cover |
| 2027 | RING/SLEEVE-INJECTION VALVE |
| 2028 | BUSHING/FUEL OIL VALVE-R 10/13 |
| 2029 | Sleeve, Injection Valve |
| 2030 | O-Ring |
| 2031 | Impact Bolt |
| 2032 | Slide Shoe |
| 2033 | circlip |
| 2034 | Tapered seat lock |
| 2035 | Adjusting Screw Rocker Arm |
| 2036 | Gasket |
| 2037 | Stud M12X20, Set Screw |
| 2038 | Male Stud |
| 2039 | Pipe,Lub.Oil Bracket Roc.Arms |
| 2040 | T-Connector |
| 2041 | Nut, Adj. Screw Rocker Arm |
| 2042 | Adjusting Screw Rocker Arm |
| 2043 | Chain |
| 2044 | Chain lock |
| 2045 | Roller bearing |
| 2046 | Circlip |
| 2047 | Big end bearing, Upper |
| 2048 | Big end bearing. Lower |
| 2049 | Piston ring set |
| 2050 | Molycote Paste Type P74, |
| 2051 | Piston |
| 2052 | Gudgeon pin bushing |
| 2053 | Gudgeop pin |
| 2054 | circlip |
| 2055 | O ring kit Hydraulic tool ( Main bearin ) |
| 2056 | O ring kit Hydraulic tool ( Con rod bearing) |
| 2057 | O ring kit Hydraulic tool ( Cylinder head) |
| 2058 | Nipple |
| 2059 | Slinger |
| 2060 | Socket screw |
| 2061 | Lockin washer |
| 2062 | Socket screw |
| 2063 | Locking washer |
| 2064 | Set of spares screws |
| 2065 | Filter Mat |
| 2066 | Turbine Blade |
| 2067 | Lockin plate Set |
| 2068 | Dampin wire |
| 2069 | Shaft machined |
| 2070 | Inducer wheel |
| 2071 | Compressor wheel |
| 2072 | Gas inlet casin machined |
| 2073 | Gas outlet casin machined |
| 2074 | Nozzle rin |
| 2075 | Cover ring |
| 2076 | Diffuser Machined |
| 2077 | Flexible connections ( including flexible bellows of FW/SW/crank case breather pipe/ Lube oil system, etc) |
| 2078 | Spring |
| 2079 | O Ring |
| 2080 | nozzle |
| 2081 | gasket |
| 2082 | washer |
| 2083 | gasket |
| 2084 | collar nut |
| 2085 | spindle assembly |
| 2086 | Gasket |
| 2087 | Copaslip (high temperature anti seize compound |
| 2088 | SPILL PLUG (erosion plug & its washer |
| 2089 | Seal washer |
| 2090 | Seal Washe r |
| 2091 | erosion plug |
| 2092 | coper gasket for fuel pump connection |
| 2093 | push rod follower |
| 2094 | o ring |
| 2095 | Spring |
| 2096 | Push rod |
| 2097 | Cam follower |
| 2098 | Circlip |
| 2099 | Cam roller |
| 2100 | Screw |
| 2101 | Lock washer |
| 2102 | Shaft. cam roller |
| 2103 | Bushing |
| 2104 | Flexiable fuel connections |
| 2105 | Filter-element |
| 2106 | Gasket Kit |
| 2107 | Filter elements |
| 2108 | Centrifugal filter overhauling kit + paper insert kit |
| 2109 | CA cooler gasket kit ( Air side a water side |
| 2110 | Anode set |
| 2111 | Gasket |
| 2112 | Gasket |
| 2113 | Sea water pump overhaul kit { If engine driven) |
| 2114 | Gasket |
| 2115 | Gasket |
| 2116 | Gasket |
| 2117 | Gasket |
| 2118 | Gasket |
| 2119 | Gasket |
| 2120 | Gasket |
| 2121 | Sealing ring |
| 2122 | Valve spindle |
| 2123 | Spring |
| 2124 | Gasket |
| 2125 | Locking wire |
| 2126 | Cylinder head overhauling kit |
| 2127 | O ring |
| 2128 | Gasket |
| 2129 | Gasket Sealing Frame Cyl. Hea |
| 2130 | Inlet Valve |
| 2131 | Circlip |
| 2132 | Lock Ring Valve Spindle |
| 2133 | Sleeve, outer |
| 2134 | Hose Clamp |
| 2135 | Gasket |
| 2136 | Hex.Lock Nut |
| 2137 | Gasket |
| 2138 | Valve Seat |
| 2139 | Exhaust Valve Guide |
| 2140 | O ring |
| 2141 | Bushing, Bearing Bracket |
| 2142 | Shafti Rocker Arm Exh,Valve |
| 2143 | Bushing, Bearing Bracket |
| 2144 | Disc, Rocker Arm Shaft ( washer} |
| 2145 | Circlip A 40 |
| 2146 | Shaft, Rocker Arm, Inlet Valv |
| 2147 | Bushing Rocker Arm |
| 2148 | Valverotator, K/L-Engine |
| 2149 | Exh. Valve |
| 2150 | O ring , Valve guide |
| 2151 | Inlet valve guide |
| 2152 | Megaseal |
| 2153 | Molycote 55M ( big bottle) |
| 2154 | Tandem overhaul kit |
| 2155 | Cross disc |
| 2156 | Ball bearing |
| 2157 | Circllp |
| 2158 | Clamp Hng |
| 2159 | Screw |
| 2160 | Lock washer |
| 2161 | Sealing ring |
| 2162 | Gasket kit |
| 2163 | Circiip |
| 2164 | Screw |
| 2165 | lock nut |
| 2166 | Sealing ring |
| 2167 | Gasket |
| 2168 | Piston rin |
| 2169 | Safety tink |
| 2170 | Bearin Complete CE |
| 2171 | Bearing Complete TE |
| 2172 | Socket strew |
| 2173 | Lockin washer |
| 2174 | Sealing Bush —TE |
| 2175 | Sealin Bush- CE |
| 2176 | Gasket |
| 2177 | Hex, Headed Screw |
| 2178 | Verbuscri Disc |
| 2179 | Locking safety feature |
| 2180 | Hex. Headed Screw |
| 2181 | locking Plate |
| 2182 | Guide bush |
| 2183 | Hex. Headed Bolt |
| 2184 | Lockln plate |
| 2185 | Hex. Headed Bolt |
| 2186 | Lockin plate |
| 2187 | INTERMEDIATE SERVICE KIT |
| 2188 | MAJOR SERVICE KIT |
| 2189 | BOWL SPINDLE |
| 2190 | WORM WHEEL SHAFT |
| 2191 | WORM WHEEL |
| 2192 | SIGHT GLASS |
| 2193 | FRICTION BLOCK |
| 2194 | GAUGE GLASS OIL |
| 2195 | RECTANGULAR RING |
| 2196 | INTERMEDIATE SSRVICE KIT |
| 2197 | MAJOR SERVICE KIT |
| 2198 | 3-YEARS SERVICE KIT |
| 2199 | SERVICE KIT FOR PUMP |
| 2200 | VERTICAL DRIVING DEVICE |
| 2201 | WORM WHEEL SHAFT |
| 2202 | WORM WHEEL |
| 2203 | FRICTION BLOCK |
| 2204 | BALL BEARING HOUSING |
| 2205 | CAP NUT |
| 2206 | PISTON RINGS SET * TD/TBD |
| 2207 | TBD PISTON+G PIN+CIRCLIPS |
| 2208 | LINER-PLATEU HONED FINISH |
| 2209 | O-RING VITON 125X4 |
| 2210 | CONN ROD BIG END BOLT |
| 2211 | BUSH-CONNROD -S/END |
| 2212 | CONN ROD BRG TOP+BOTTOM |
| 2213 | SPRING DOWEL PIN M4X20MM |
| 2214 | SET OF GASKET-TBD V12 HE |
| 2215 | SET OF HOSES * TBD V12 HE |
| 2216 | SET OF HOSECLIPS-TBDV12HE |
| 2217 | SET OF O RINGS TBD V12 HE |
| 2218 | SET-SEALING RINGS TBD2V12 |
| 2219 | HEX_BOLT_M8X20 |
| 2220 | SHC SCREW=M10X1.5X20 |
| 2221 | KEY WOODRUFF. KEY |
| 2222 | CYLINDER HEAD SEALING |
| 2223 | O RING-CHANGE OVER LUB. |
| 2224 | ROUND PACKING RING |
| 2225 | BALL BRGS 6204/2RS/C3 |
| 2226 | PUSH ROD TUBE(MODF)195MM |
| 2227 | V12 H.P.INJ.PIPES SETOF12 |
| 2228 | O RING RUBR 14X3 D/234 |
| 2229 | POLY ACRYLIC RUBBER BELOW |
| 2230 | RUBBER BELLOW DRY SUMP |
| 2231 | SEGMENTED GASKET-V12 SUMP |
| 2232 | GASKET IN PERMANITE |
| 2233 | GASKET IN PERMANITE |
| 2234 | GASKET- OIL FILLER NECK |
| 2235 | O' RING |
| 2236 | O'-RING NBR 32X4 |
| 2237 | O'-RING NBR 140X4 |
| 2238 | O' RING 33X3.5 |
| 2239 | HEXSCREW=M8X1.25X25 CL8.8 |
| 2240 | SPRING WASHER B-8 |
| 2241 | O'-RING SILICON 20 X 4 |
| 2242 | SPRING WASHER M-10 |
| 2243 | O-RING NBR 124X3 |
| 2244 | OILSEAL=110X90X12 MM THK |
| 2245 | GASKET-GEAR END COVER |
| 2246 | ADJ.SCREW=M10X1.5X39 LG. |
| 2247 | HEX. NUT M10 DIN 934M-10 |
| 2248 | BRASS SLEEVE |
| 2249 | CU.SLEEVE |
| 2250 | O-RING SILICON 18.2X3.4 |
| 2251 | COPPER WASHER |
| 2252 | INSERTS V S INL/EXH |
| 2253 | VALVE SPRING=61MM HEIGHT |
| 2254 | VALVE SPRING |
| 2255 | ROTOCAP SOLID |
| 2256 | SPRING CAP D2 |
| 2257 | VALVE GUIDE D2 |
| 2258 | VALVE EX D2 KV 2994 -KRAZ INL-EXT COMMON |
| 2259 | VALVE STEAM SEAL - TBD2 ENGINE |
| 2260 | HALF COLLET |
| 2261 | INJ. STUD M10 |
| 2262 | GASKET-AIR INTAKE MANIFOD |
| 2263 | GASKET EXHAUST MANIFOLD |
| 2264 | SLEEVE CYL.HEAD FOR OIL |
| 2265 | COVER=25X1.5X11MM WIDTH |
| 2266 | HEXBOLT=M8X1.25X55 8.8CL |
| 2267 | HEXBOLT=M16X150 10.9 D931 |
| 2268 | WASHER-CYL.HEAD=28X2.0 |
| 2269 | GASKET CYL HEAD COVER |
| 2270 | O-RING VITON-18MMX5.0MM |
| 2271 | O RING VITON 9X4.5MM |
| 2272 | COPPER_WASHER |
| 2273 | AIR FILTER 100 MM |
| 2274 | H O S E 75 X 45 |
| 2275 | HOSECLIP 70-90/4 |
| 2276 | HOSE 22DIA.X 80L SILICON |
| 2277 | HOSECLIP 70-90/4 |
| 2278 | HOSE 76 ID X65L.SILICON. |
| 2279 | A V MOUNTG-A2T/4030B |
| 2280 | HOSE 50DIA.X55L.SILICON |
| 2281 | HOSECLIP 60-80/3X |
| 2282 | HOSE 90DIA.X 65L.SILICON |
| 2283 | HOSE CLIP AIR FLTR 87MM |
| 2284 | HEX-BOLT-M10X25 |
| 2285 | HEX SCREW M10X30LG |
| 2286 | ZINC ANODE 1/2\\" BSP ASSLY |
| 2287 | GASKET-AFTERCOOLER COVER |
| 2288 | GASKET - A/COOLER |
| 2289 | GASKET - A/COOLER |
| 2290 | GASKET IN TALBRITOL |
| 2291 | GASKET-EXH MANIFOLD FLANG |
| 2292 | GASKET IN D'CEMJO |
| 2293 | GASKET IN TALBRITOL |
| 2294 | ZINC ANODE ASSLY |
| 2295 | OVER HAUL T/C KIT K27 -53277110008 |
| 2296 | STUD M10X180X8.8 |
| 2297 | GASKET-EXH. JUNCTION |
| 2298 | GASKET - TURBOCHARGER |
| 2299 | GASKET-TURBOOIL DRAINPIPE |
| 2300 | GASKET-TURBO OIL SUPPLY |
| 2301 | O-RING VITON 80X3.8 |
| 2302 | STAR WASHER-OIL COOLER |
| 2303 | O-RING VITON 101X4.5 |
| 2304 | O-RING VITON 20X4 |
| 2305 | STEEL BALL 3/4\\" DIA. |
| 2306 | COMP SPRING CYLINDRICAL D2 LOC |
| 2307 | O-RING SILICON 35X3 |
| 2308 | RING 28X3.5 |
| 2309 | O RING SILICON 24X3.5 |
| 2310 | LUB OIL FILTER(232V12) |
| 2311 | Filter Element(Max10)(S3209T) |
| 2312 | V12 OVERFLOW PIPE 1030 |
| 2313 | FILTER PLASTIC BOWL(RK30051) |
| 2314 | BALLBRG.55X90 /6011/22 |
| 2315 | BALLBRNG /6206/C3 |
| 2316 | CU-WASHER |
| 2317 | FLANGE-INJECTOR |
| 2318 | SEAL-WASHER-20X9.5X2MM |
| 2319 | O` RING-NBR 80X3 |
| 2320 | OIL SEAL - 30X52X10 |
| 2321 | SCREWED ROD 95 MMLG |
| 2322 | Balll Joint M6 – RH Thds |
| 2323 | Ball Joint M6-LH Thds |
| 2324 | PSF-8-M6X1 SWIVEL JOINT |
| 2325 | PSFL-8-M6X1 SWIVEL JOINT |
| 2326 | O RING NBR 20X3 |
| 2327 | COGGED BELT AX-40 |
| 2328 | HOSE-80DIA.X 70L. |
| 2329 | HOSE 40 DIA.X60L. |
| 2330 | HOSE CLIP40-60(2X)9THK. |
| 2331 | HOSE CLIP 25-40/1X |
| 2332 | HOSE 30DIA.X55L |
| 2333 | GASKET |
| 2334 | GASKET-WATER PIPE OILCOOL |
| 2335 | GASKET-COOLING WATER PIPE |
| 2336 | O RING FOR HE CAP. |
| 2337 | RAD.CAP+NECK-TANK PLUG |
| 2338 | GASKET-3-THERMOSTAT CASNG |
| 2339 | GASKET |
| 2340 | RUBBER RING |
| 2341 | GASKET |
| 2342 | PUMP SHAFT |
| 2343 | BEARING |
| 2344 | MECHANICAL SEAL |
| 2345 | OIL SEAL |
| 2346 | IMPELLER SWP |
| 2347 | IMPELLER SCREW WITH WASHER |
| 2348 | GASKET |
| 2349 | GASKET WATER MANIFOLD |
| 2350 | RING NBR 53 X 4 |
| 2351 | OVAL GASKET |
| 2352 | GASKET |
| 2353 | SOCKET 12MM PMS COUPLING |
| 2354 | PISTON COOLING NOZZLE |
| 2355 | CU. WASHER 16X22X1.5THK |
| 2356 | HEXNUT COPR.PLATED M8 10G |
| 2357 | HEXBOLT=M12X1.75X50 8.8/C |
| 2358 | CAP BRASS Dia 30 |
| 2359 | HEX PLUG M14X1.5 |
| 2360 | HEXBOLT=M10X1.5X90 8.8/CL |
| 2361 | ALN SCREW M8X30 912 12.9 |
| 2362 | STUD BOLT M10X70 8.8/CL |
| 2363 | STUD BOLT M12X35 12.9CL |
| 2364 | HEX SCREW M10X60 8.8/CL |
| 2365 | HEX SCRREW-M10X40-933-8.8 |
| 2366 | STUD BOLTS |
| 2367 | PLAIN WASHER A10.5 (M10) |
| 2368 | FLEXIBLE PIPE 580MM |
| 2369 | FLEXIBLE PIPE 530MM |
| 2370 | FLEXIBLE PIPE 450MM |
| 2371 | FLEXIBLE PIPE 1500MM |
| 2372 | FLEXIBLE PIPE 1000MM |
| 2373 | FLEXIBLE PIPE 1050MM |
| 2374 | FLEXIBLE PIPE 720MM |
| 2375 | FLEXIBLE PIPE 600MM |
| 2376 | FLEXIBLE PIPE 800MM |
| 2377 | FLEXIBLE PIPE 600MM |
| 2378 | FLEXIBLE PIPE 3000MM |
| 2379 | FLEXIBLE PIPE 2500MM |
| 2380 | NOZZLE+INJ+HOLDR-TBD |
| 2381 | INJECTOR NOZZEL TD/TBD |
| 2382 | FUEL PUMP SHAFT |
| 2383 | FUEL INJ. PUMP DRIVE |
| 2384 | PRESSURE GAUGE. |
| 2385 | LOT GAUGE 40/130DEG 2445L |
| 2386 | W.T.GAUGE 1380MMT CAPIL. |
| 2387 | BATT. CHRG. ALT. 24V, 55AMPS LUCAS |
| 2388 | COUPL FOR\\"P\\"TY.PUMP V12 |
| 2389 | CAMSHAFT V12 FINISHED |
| 2390 | CAM GEAR ASSLY |
| 2391 | THERMOSTAT ELEMENT |
| 2392 | 3-THERMOSTAT CASING MARIN |
| 2393 | Turbocharger TEL 53279706457 |
| 2394 | LUB.OIL PUMP |
| 2395 | WATER PUMP ASSEMBLY D4/D4-I |
| 2396 | PUSH ROD TUBE(MODF)195MM |
| 2397 | PUSH ROD |
| 2398 | TAPPET D2 ENGINE |
| 2399 | RING FOR CRANKSHAFT |
| 2400 | ROCKER LEVER ARM |
| 2401 | ROCKER BLOCK FOR R/ARM |
| 2402 | SEGMENT SUR NITR TREAT |
| 2403 | AIR DISTRIBUTER V12 (*) |
| 2404 | AIR STARTING VALVE (IMP) |
| 2405 | AIR STARTING PIPES |
| 2406 | AIR STARTING PIPES |
| 2407 | AIR STARTING PIPES |
| 2408 | AIR STARTG PIPE |
| 2409 | VALKAN COUP.L-2613 . |
| 2410 | MAG.PICK UP-5/8\\"UNF 50mm |
| 2411 | ACTUATOR ADC 225 S 24V |
| 2412 | Governor DPG2201 |
| 2413 | Volt meter selector switch salzer |
| 2414 | Ammeter selector switch salzer |
| 2415 | Rotary switch salzer 2 Pole ON/OFF B13 Mounting (for space heater ) |
| 2416 | Rotary switch salzer 2 Pole 2 Way & OFF (For local / remote selection ) |
| 2417 | Rotary switch salzer 1 Pole ON/OFF (For auto manual selection) |
| 2418 | Push Button Teknic 22.5 Dia Blue |
| 2419 | Push Button Teknic 22.5 DiaYellow (For loading solenoid Valve) |
| 2420 | Push Button Teknic 22.5 Dia White (For unloading Solenoid Valve) |
| 2421 | Mushroom Red Push Button Teknic (Emergency Stop) |
| 2422 | Indicating lamp Teknic 22.5 Dia LED 230V AC Type:Red |
| 2423 | Indicating lamp Teknic 22.5 Dia LED 230V AC Type:Yellow |
| 2424 | Indicating lamp Teknic 22.5 Dia LED 230V AC Type:Blue |
| 2425 | Indicating lamp Teknic 22.5 Dia LED 230V AC Type:Green |
| 2426 | Lube Oil for AC Plant . Savita Chemicals SAVSYN2068 |
| 2427 | Set of Fastners |
| 2428 | Pilot Operated solenoid valve sporlan Type 180S with 230V AC Coil |
| 2429 | Coil for Pilot Operated solenoid valve sporlan type 180S with 230V AC Coil |
| 2430 | Capacity Control Solenoid valve kit |
| 2431 | Pressure switch make: Dabfoss RT5 Range :4 to 17 bar |
| 2432 | Internal Oil Filter Element |
| 2433 | Refrigerant Suction Filter |
| 2434 | Compressor Oil Heater |
| 2435 | Integral Oil Separator Heater Kit |
| 2436 | Piston Ring (Glyd Ring) Set |
| 2437 | Capacity Control Piston Spring |
| 2438 | Capacity Control Piston |
| 2439 | Motor Protection relay, |
| 2440 | Oil Filter Replacement Gasket & O Ring Set |
| 2441 | Motor Replacement Gasket & O Ring set |
| 2442 | Full Gasket & O Ring set |
| 2443 | Filier Drier fo POSV |
| 2444 | Set of Gasket for condenser for 80 TR AC Plant |
| 2445 | Cathodic Bolt |
| 2446 | 4-1/8\\" Angle valve spare kit |
| 2447 | 2-1/8\\" Angle valve spare kit |
| 2448 | 1-5/8\\" Angle valve spare kit |
| 2449 | 5/8\\" Angle valve spare kit |
| 2450 | 1-3/8\\" Globe Valve spare kit |
| 2451 | 7/8\\" Globe Valve spare kit |
| 2452 | 1-5/8\\" Globe Valve Spare kit |
| 2453 | 5/8\\" Globe valve spare kit |
| 2454 | Differential pressure gauge -switch Hirlekar,(0 to 0.5kg/cm2) |
| 2455 | Gasket set for condenser |
| 2456 | Pressure gauge, Make -WIKA, Dial Size -63 mm, Range : 0 to 10 kg/cm2,mounting Type:Gauge Board |
| 2457 | Pressure gauge, Make -WIKA, Dial Size -63 mm, Range :(-) 1 to 15 kg/cm2g,(With corresponding saturation tempreature making for R134A refrigerant) Mounting Type :Gauge Board |
| 2458 | Pressure gauge,Make -WIKA, Dial Size -63mm, Range :0 to 25Kg/cm2g |
| 2459 | Armaflex Class 1 Insulation tube, Size:16 mm ID, Thk:19 mm, Make: Armaflex |
| 2460 | Armaflex Class 1 Insulation tube, Size:22.5 mm ID, Thk:19 mm, Make: Armaflex |
| 2461 | Armaflex Class 1 Insulation tube, Size:45 ID, Thk:25 mm, Make: Armaflex |
| 2462 | Armaflex Class 1 Insulation tube, Size:28 mm ID, Thk:25 mm, Make: Armaflex |
| 2463 | Strainer for SW pump of REF Plant |
| 2464 | 5/8\\" Globe valve spare kit |
| 2465 | 7/8\\" Globe Valve spare kit |
| 2466 | 1-1/8\\" Globe Valve spare kit |
| 2467 | Gasket set for condenser |
| 2468 | Cathodic Bolt |
| 2469 | Cathodic Bolt |
| 2470 | ELECTRICAL |
| 2471 | PTFE packing ring |
| 2472 | Ocating Flange Gasket |
| 2473 | Flange Gasket Bottom |
| 2474 | Bush for EM Log |
| 2475 | Master Controller Module assy |
| 2476 | Engine Mdoule Assy |
| 2477 | Power Supply Module Assy |
| 2478 | Display Module Assy |
| 2479 | Fuse, Cartridge , 1A , 5*15mm, 0229001.HXP |
| 2480 | Fuse Cartridge, 2A, 250V, 5mm*15mm, 0229002.HXP |
| 2481 | Fuse Cartridge, 3A, 6.3mm * 32mm |
| 2482 | Fuse Cartridge, 15A, 6.3mm * 32mm |
| 2483 | cooling Fan, 48V DC, MEC0384v/-000U-a99 |
| 2484 | Transceiver Mdoule CH1 Assy |
| 2485 | Transceiver Mdoule CH2 Assy |
| 2486 | SP Module Assy |
| 2487 | Communication Card Assy |
| 2488 | Power Supply Module Assy |
| 2489 | 4PDT Switch |
| 2490 | fuse, 3A |
| 2491 | Fuse, 10A |
| 2492 | Power Supply, VGS-100-24 |
| 2493 | Relay, MPR2C12D |
| 2494 | Diode, MBR1660 |
| 2495 | Regulator-LM7812CT |
| 2496 | Echosounder - V3 (Dual Channel) |
| 2497 | Transducer Assy 33 kHz |
| 2498 | Cable Assembly -2 |
| 2499 | Transducer Assy 210 kHz |
| 2500 | Cable Assembly - 3 |
| 2501 | Junction Box Assy 33 kHz |
| 2502 | Junction Box Assy 210 kHz |
| 2503 | LED Repeater Unit |
| 2504 | VGA Repeater Unit |
| 2505 | Cable Assembly -5 |
| 2506 | Cable Assembly -7 |
| 2507 | Cable Assembly -9 |
| 2508 | Printer |
| 2509 | MS Connectoer MS 3106 F 14S 7PY |
| 2510 | MS Connectoer MS 3106 F 14S 7PW |
| 2511 | MS Connectoer MS 3106 F 14S 7PX |
| 2512 | MS Connectoer MS 3106 F 14S 7SX |
| 2513 | MS Connectoer MS 3106 F 14S 5S |
| 2514 | MS Connectoer MS 3106 F 14S 2S |
| 2515 | Snap Ferrite - 742 711 32 |
| 2516 | Technical Documents |
| 2517 | Transceiver Module Assy CH2 (210 kHz) |
| 2518 | Transceiver Module Assy CH1 (33 kHz) |
| 2519 | SP Module Assy |
| 2520 | Communication Module Assy |
| 2521 | Power Supply Module Assy |
| 2522 | 4PDT Switch |
| 2523 | Fuse, 3A |
| 2524 | VALVE REGULATED LEAD ACID(VRLA) BATTERY |
| 2525 | ONLINE UPS |
| 2526 | BOLT & NUT FULL THREAD GI M10X25 |
| 2527 | SHOCK MOUNT |
| 2528 | NECOL LACQUER |
| 2529 | CABLES AND CONNECTORS |
| 2530 | KU BAND SPARES |
| 2531 | SCREW SELF TAPING PH STAR H NO.6X32MM,GI |
| 2532 | TAPE PVC ADHESIVE (ELE. INSULATION) 19MM YELLOW |
| 2533 | TAPE PVC ADHESIVE (ELE. INSULATION) 19MM RED |
| 2534 | KLI-NIT CONTACT CLEANER SPRAY- 350 ML |
| 2535 | MASKING TAPE 2\\" WIDTH |
| 2536 | CELLO TAPE CLEAR 50 MM. WIDTH. |
| 2537 | WD 40 SPRAY BOTTLE (400 ML) |
| 2538 | 3 CORE 35 SQMM MARINE CABLE |
| 2539 | MAGNETIC CONTACTOR 25A, BCH, CE15EN3-B |
| 2540 | THERMAL OVER LOAD RELAY |
| 2541 | ELMEX CONNECTOR 4 SQ.MM,MAKE: |
| 2542 | ELMEX CONNECTOR 10 SQ.MM, |
| 2543 | MCB - 2 POLE, 16A , MAKE :LEGRAND |
| 2544 | ROTARY ON/OFF SEL SWITCH 3 POLE 16A 440V |
| 2545 | TAPPER ROLLER BEARING SKF 30310 |
| 2546 | STRIP CONNECTOR BAKELITE15/A/500V |
| 2547 | OIL SEAL 55- 70- 10 |
| 2548 | HAMMER TONE LIGHT SILVER GREY PAINT. |
| 2549 | SELF DRILLING SCREW GI NO:8X19MM |
| 2550 | 240/415V, 3POLE ,16A ,16KA ,MCB |
| 2551 | BEARINGS SKF 6206 ZZ C3 |
| 2552 | HF TX/ RX PRC 6020 ACCESSORIES |
| 2553 | SHOCK MOUNT |
| 2554 | DAT RECORDER (DMR-16A) ACCESSORIES |
| 2555 | SHOP MOUNTS |
| 2556 | UPS, BATTERIES AND CABLES |
| 2557 | SENSORS |
| 2558 | SPARES FOR INTERFACING |
| 2559 | DISPLAY |
| 2560 | UPS EATON 3KVA MKVI.230 VAC(DVN) |
| 2561 | FAN FOR UPS PW9130(PART NO : 370313) |
| 2562 | INSTALLATION ACESSORIES & CABLES |
| 2563 | BATTERY HRL 12110W(CSB)12V |
| 2564 | CNODE MINI 34 TRANSPONDER |
| 2565 | AIR LUBRICATOR 3/8\\" |
| 2566 | RELAY RM 111 12VDC(PART NO : 44240737) |
| 2567 | POWER SUPPLY 7414.24V-5A |
| 2568 | POTMETER RCP FOR GIMBELHEAD |
| 2569 | EM9 PCB(PART NO : 700264 |
| 2570 | LIMIT SWITCH XSM H04713 GTW |
| 2571 | LTW AIR PRESSURE REGULATOR |
| 2572 | AIR PRESSURE REGULATOR |
| 2573 | MOUNTING PLATE FOR VALVE563-301 |
| 2574 | OIL AIR LUBRICATOR |
| 2575 | VALVE 563-301 WITHOUT SOLENOID |
| 2576 | SOLENOID FOR VALVE 563-301 |
| 2577 | SERVO MOTOR COOLING FAN |
| 2578 | VALVE,DRAIN 3/8\\" 352-034 G3/8\\" |
| 2579 | MANO METER 0-10B |
| 2580 | SEALSET BOOM CYLINDER(PART NO :44236024) |
| 2581 | MANO METER,0-250B |
| 2582 | LTW GASKET KIT TENSION CYLINDER |
| 2583 | LTW LOAD CELL SB5000(PART NO : 701039) |
| 2584 | PCB TRX32(PART NO : 303088) |
| 2585 | PCB TRX32 FILTER MF W/FRONT PANEL |
| 2586 | PATCH CABLE(PART NO : 310688) |
| 2587 | SERVOMOTOR MDFRARS(PART NO : 301684) |
| 2588 | POWER SUPPLY 24V(PART NO : 310181) |
| 2589 | POWER MODULE TRU HIPAP 350 |
| 2590 | PRESSURE GAUGEØ40 0-10BAR,PART NO:303434 |
| 2591 | HYDRAULIC OIL |
| 2592 | HYDRAULIC LINE ASSEMBLY |
| 2593 | VRVT 100/E/SM/030 E4 |
| 2594 | CNODE MINI -BATTERY(PART NO : 220675) |
| 2595 | MRU-E-JB1(FOR MRU 2) |
| 2596 | WIRE ROPE, 12MM, MS |
| 2597 | HIPAP APOS FULLY LOADED OS |
| 2598 | TRACKBALL(PART NO : 354149) |
| 2599 | KEYBOARD(PART NO :719-098786) |
| 2600 | MOUNTING KIT(PART NO : 331385) |
| 2601 | CONSOLE ACESSORIES |
| 2602 | ETHERNET SWITCH EDS-510A |
| 2603 | PLUGABLE TRANSCEIVER SFP-1GSXLC |
| 2604 | BLUESTORM UNIVERSAL PCI |
| 2605 | DATA SWITCH ASSY TRU X21 |
| 2606 | O RINGS(PART NO : 540-045951) |
| 2607 | LTW AIR TANK,0L.10B.MK8-15 |
| 2608 | LTW LOAD CELL AMPLIFIER |
| 2609 | SHUT-OFF VALVE 3/23/8\\"(PART NO : 327577) |
| 2610 | WIRECLAMP SET(PART NO : 700161) |
| 2611 | HYDRAULIC VALVE(PART NO:700254) |
| 2612 | DISTRIBUTION UNIT FOR GYRO COMPASS |
| 2613 | ACCELEROMETER |
| 2614 | ACCELEROMETER |
| 2615 | INTERNAL CABLE -RATE SENSOR |
| 2616 | WIND OBSERVER II(PART NO: 700801) |
| 2617 | WIND DISPLAY OMC-139(BOW UP) |
| 2618 | WIND DISPLAY OMC-139(BOW DOWN) |
| 2619 | INSTALLATION MATERIALS |
| 2620 | 4X2X0.75 SQ.MM SCREENED, COPPER |
| 2621 | TRANSDUCER HEAD(PART NO: TDH-Z12000) |
| 2622 | SERVICE KIT TD CABLE HL 3770 |
| 2623 | N-CONNECTOR FOR 1/2\\" SUPER FLEX M |
| 2624 | N-CONNECTOR FOR 1/2\\" SUPER FLEX M |
| 2625 | DP OS WITH SOFTWARE |
| 2626 | RMP 201-8(PART NO : 324400) |
| 2627 | DISPLAY 27\\"LCD MD27 KM05 |
| 2628 | KEYBOARD COMPACT US AK-4100 |
| 2629 | PANEL ALC(PART NO: 603526) |
| 2630 | PANEL BU DP(PART NO : 603530) |
| 2631 | RCU 502(PART NO : 330924) |
| 2632 | FAN FOR RCU 502 CONTROLLER |
| 2633 | RSER 200-4(PART NO :603444) |
| 2634 | MOXA ETHERNET SWITCH EDS -316 |
| 2635 | PANEL INPUT MK2 COP 5 |
| 2636 | JOYSTICK KC 06-K |
| 2637 | RMP 201-8(PART NO : 324400) |
| 2638 | RSER 200-4(PART NO :603444) |
| 2639 | DP HEADING WHEEL FOP |
| 2640 | TBUS CONTACT & ACESSORIES |
| 2641 | RF CO-AXIAL CABLE RG213 |
| 2642 | 12V & 28Ah batteries |
| 2643 | MOTOR THRUSTER ACCESSORIES |
| 2644 | PUMP ACCESSORIES |
| 2645 | MOTOR ACCESSORIES |
| 2646 | LIGHT WEIGHT TAUT WIRE ACCESSORIES |
| 2647 | HYDRAULIC AND AIR SYSTEM CABINET LOCKING HANDLE |
| 2648 | AIR CYLINDER WITH VALVE |
| 2649 | AIR BELLOW |
| 2650 | LOCAL CONTROL CABINET COVER |
| 2651 | DEPRESSOR WEIGHT BASKET |
| 2652 | WEIGHT CATCHER |
| 2653 | HYDRAULIC HOSE |
| 2654 | PNEUMATIC LINES |
| 2655 | LIGHT WEIGHT TAUT WIRE SYSTEM ACCESSORIES |
| 2656 | WIRE TENSION METER |
| 2657 | HYDRAULIC MANOMETER |
| 2658 | RRM000439943 Spare Part Kit |
| 2659 | GM4-04 Gasket |
| 2660 | 218-025X035X07 Seal Ring |
| 2661 | 212-0568-26 O-Ring |
| 2662 | 212-0187-26 O-Ring |
| 2663 | 412-6005.C2 Ball Bearing |
| 2664 | 7 pcs 17 433-B095 Flexible Coupling Element |
| 2665 | 381-A025 Locking Ring |
| 2666 | GM4 Gasket |
| 2667 | 220-41 Seal Ring |
| 2668 | 5R-S35PM Spare Part Kit |
| 2669 | 212-0203-26 O-Ring |
| 2670 | 212-0234-35 O-Ring |
| 2671 | 381-A020 Locking Ring |
| 2672 | 5R-FV2 Spare Part Kit |
| 2673 | 801-038-13 Seal Washer |
| 2674 | 801-038-16 Seal Washer |
| 2675 | 801-038-19 Seal Washer |
| 2676 | 381-A030 Locking Ring |
| 2677 | 381-A035 Locking Ring |
| 2678 | FV2-52 FV2-52 Seal |
| 2679 | FV2-65 Lock Nut |
| 2680 | RV1-09 Support Ring |
| 2681 | 801-038-05 Seal Washer |
| 2682 | RUBBER STOCK SEAL |
| 2683 | RUDDER ANGLE AMPLIFIER PCB |
| 2684 | ALARM PANEL RELAY |
| 2685 | LIMIT SWITCH |
| 2686 | EN - 8 ROUND ROD 18 MM DIA |
| 2687 | EN8-HEXAGONAL ROD 19MM A/F |
| 2688 | ALLEN BOLT M14 X 45 X 45 |
| 2689 | BOLT FULL THREAD SS ALLEN M12X35 |
| 2690 | NUT SS M12 |
| 2691 | WASHERPLATE SS M12 |
| 2692 | SPRING WASHER SS M12 |
| 2693 | BOLT & NUT FULL THREAD SS M12X40 |
| 2694 | WASHERPLATE SS M10 |
| 2695 | SPRING WASHER SS M10 |
| 2696 | BOLT FULL THREAD SS M10X40 |
| 2697 | SILICON SEALENT CLEAR VIEW. |
| 2698 | CNAF JOINTING SHEET 1MM OIL GRAPHITED |
| 2699 | BOLT & NUT FT M12X35 ALLEN H.T GR 8.8 |
| 2700 | BOLT FULL THREAD H.T ALLEN M12X25 |
| 2701 | RUDDER STOCK BOTTOM SEAL |
| 2702 | RUDDER STOCK TOP SEAL |
| 2703 | RUDDER STOCK BOTTOM SEAL |
| 2704 | RUDDER STOCK TOP SEAL |
| 2705 | DOUBLE LIP OIL SEAL:- 25 - 35 - 7 |
| 2706 | NEOPRINE O RING 25 OD X 2.5MM CSD |
| 2707 | NEOPRENE O RING 57 ID X 2.5MM CSD |
| 2708 | CIRCLIP EXTERNAL - SHAFT DIA 25 MM |
| 2709 | NEOPRENE O RING 25 OD X 3MM CSD |
| 2710 | DOUBLE LIP OIL SEAL:- 25 - 35 - 7 |
| 2711 | LIP SEAL 24-35-7 |
| 2712 | NEOPRENE O RING 60 OD X 3.5MM CSD |
| 2713 | BALL BEARING 6005-2Z |
| 2714 | ALLEN BOLT M8X90X24 GR.12.9 |
| 2715 | O' RING KIT |
| 2716 | TAP SET M14 X 2MM PITCH |
| 2717 | HACKSAW BLADE 300 X 12.5MMX18TPI HSS |
| 2718 | NEOPRENE CHORD 2 MM |
| 2719 | NEOPRENE CHORD 2.5 MM |
| 2720 | NEOPRENE CHORD 3 MM |
| 2721 | ALLEN BOLT M14 X 45 X 45 |
| 2722 | ALLEN BOLT M14 X 45 X 45 |
| 2723 | ANABOND GASKET MAKER RED. |
| 2724 | ALLEN BOLT HIGH TENSILE M8X20 |
| 2725 | SERVO OIL SS68,PT NO.475-R014781 |
| 2726 | SERVO OIL SS68,PT NO.475-R014781 |
| 2727 | SERVO OIL SS68,PT NO.475-R014781 |
| 2728 | SERVO CEP 150 |
| 2729 | FOT PUMP |
| 2730 | SHIM,P/N.03M-102-20 |
| 2731 | SHIM,P/N.03M-102-10 |
| 2732 | SHIM,P/N.03M-102-05 |
| 2733 | SHIM,P/N.03M-102-02 |
| 2734 | SLIDE BEARING,P/N.06M-78 |
| 2735 | SLIDE BEARING,P/N.06M-77 |
| 2736 | GASKET,P/N.09M-74 |
| 2737 | O-RING,P/N.212-0218-35 |
| 2738 | SEAL WASHER,P/N.801-038-26 |
| 2739 | O-RING,P/N. 212-09450-30 |
| 2740 | SEAL WASHER,P/N.801-038-09 |
| 2741 | SEAL WASHER,P/N.801-038-19 |
| 2742 | SPIRAL SPRING,P/N.S35P-124 |
| 2743 | LOCK NUT,P/N.354-M06 |
| 2744 | PACKING CORD,P/N.211-032 |
| 2745 | PACKING CORD,P/N.211-035 |
| 2746 | O-RING,P/N. 212-2000-70 |
| 2747 | O-RING,P/N. 212-05350-40 |
| 2748 | U-RING,P/N. 217-150X170X10 |
| 2749 | SUPPORTING RING,P/N.06M-28 |
| 2750 | FLANGE SEAL,P/N.06M-15 |
| 2751 | V-RING,P/N.219-V-200A |
| 2752 | O-RING,P/N.212-0295-30 |
| 2753 | O-RING,P/N.212-2593-57 |
| 2754 | SEAL WASHER,P/N.801-038-16 |
| 2755 | SEAL WASHER,P/N.801-038-19 |
| 2756 | O-RING,P/N.212-03700-40 |
| 2757 | O-RING,P/N.212-0331-18 |
| 2758 | O-RING,P/N.212-0251-18 |
| 2759 | O-RING,P/N.212-0093-18 |
| 2760 | O-RING,P/N.212-0295-30 |
| 2761 | SEAL RING,P/N.218-025X035X06 |
| 2762 | LOCKING RING,P/N.381-A025 |
| 2763 | O-RING,P/N.212-0329-35 |
| 2764 | O-RING,P/N.212-0266-35 |
| 2765 | SEAL,P/N.FV2-52 |
| 2766 | SEAL WASHER,P/N.213-U12.7-18-1 |
| 2767 | GASKET,P/N.GM4-04 |
| 2768 | ROTOR SEAL,P/N.06M-131 |
| 2769 | ROTOR SEAL,P/N.06M-130 |
| 2770 | ROTOR SEAL,P/N.06M-129 |
| 2771 | ROTOR SEAL,P/N.06M-128 |
| 2772 | SEAL WASHER,P/N.801-038-09 |
| 2773 | SEAL,P/N.RV1-08 |
| 2774 | SPLIT PIN,P/N.387-4.0X40 |
| 2775 | SEAL WASHER,P/N.801-038-23 |
| 2776 | SEAL WASHER,P/N.801-038-16 |
| 2777 | LOCKING RING,P/N.381-A035 |
| 2778 | LOCKING RING,P/N.381-A030 |
| 2779 | SEAL RING,P/N.218-025X035X07 |
| 2780 | DISTANCE RING,P/N.GM4-02 |
| 2781 | SEAL RING,P/N.218-025X035X07 |
| 2782 | GASKET,P/N.GM6-04 |
| 2783 | GASKET,P/N.GM4-04 |
| 2784 | O-RING,P/N.212-0568-26 |
| 2785 | SEALING RETAINER,P/N.GM4-06 |
| 2786 | SEAL RING,P/N.220-41 |
| 2787 | LOCKING RING,P/N.381-A025 |
| 2788 | BALL BEARING,P/N.412-6005.C2 |
| 2789 | GASKET,P/N.GM4 |
| 2790 | LOCKING RING,P/N.381-A025 |
| 2791 | FLEXIBLE COUPLING ELEMENT,P/N.433-B095 |
| 2792 | SEAL WASHER,P/N.801-038-16 |
| 2793 | O-RING,P/N.212-0187-26 |
| 2794 | SEAL WASHER,P/N.213-U12.7-18-1 |
| 2795 | O-RING,P/N.212-0218-35 |
| 2796 | O-RING,P/N.212-0250-35 |
| 2797 | DIG. OUTPUT- PARENT ITEM -702848 |
| 2798 | ANALOGUE INPUT-PARENT ITEM -702846 |
| 2799 | UN1 CIRCUIT BOARD PARENT ITEM901151 |
| 2800 | INDICATOR |
| 2801 | PENCIL GRINDER STONE AS PER SAMPLE |
| 2802 | PENCIL GRINDER STONE AS PER SAMPLE |
| 2803 | PENCIL GRINDER STONE AS PER SAMPLE |
| 2804 | NEOPRENE O RING 20 ID X 2.8MM CSD |
| 2805 | NEOPRENE O RING 20 ID X 2.6MM CSD |
| 2806 | DIVING |
| 2807 | Set of blank 1,3/4,1/2,3/8,1/4\\" |
| 2808 | Oil seals and O ring set |
| 2809 | Digital display and temrature probe |
| 2810 | 2.5\\" pressure gauges back entry |
| 2811 | Under water depth sensor |
| 2812 | Tescom Regulator M-44-1313 |
| 2813 | Valve repair kit |
| 2814 | Underwater Lights |
| 2815 | Panel indicator RED |
| 2816 | O ring Kit |
| 2817 | Valves repair kit |
| 2818 | Hyperbaric paint. |
| 2819 | Marine signal orange |
| 2820 | O ring |
| 2821 | Gas Diffuser |
| 2822 | Scrubber fan |
| 2823 | 4 pin 8 way marine connector |
| 2824 | 3 pin marsmarine |
| 2825 | Oil for UW junction Box in ltr |
| 2826 | Sealed connector |
| 2827 | Underwater 7 Ah Battry |
| 2828 | Amron International Repair Kit |
| 2829 | Amron Radio Helespeach |
| 2830 | OBG Cylinder |
| 2831 | TWC unit |
| 2832 | Jupiter connection |
| 2833 | Blanks and special connectors |
| 2834 | BIBS single hose |
| 2835 | Innerpack Pump |
| 2836 | 120 mm Umblical Cutter |
| 2837 | Rat replant |
| 2838 | UPS 4kwa |
| 2839 | Hyperbearic paint |
| 2840 | Neoprine gasket |
| 2841 | Underwater Gauge |
| 2842 | Tungum tube 1/2 |
| 2843 | U/W camera |
| 2844 | Bushes and rod |
| 2845 | Repair kit |
| 2846 | Repair Kit |
| 2847 | Service kit |
| 2848 | Diver umbilicals |
| 2849 | Divers Bell valves |
| 2850 | Tungum pipes and fitting |
| 2851 | Diver bell JB fittings |
| 2852 | Neck valves onboard gas bottles |
| 2853 | 24Volts DC fan of Scrubber |
| 2854 | 24V DC, SDC Bell rectifier |
| 2855 | 12/24V, portable charger for SDC |
| 2856 | Oxygen analyser |
| 2857 | Water heater for diver |
| 2858 | Diving Bell external light 300 mtrs |
| 2859 | Safety net |
| 2860 | Tungam pipes |
| 2861 | Starter panel of Diving Trolley |
| 2862 | U/W camera |
| 2863 | Seal kit for control Lever |
| 2864 | Hot water alarm |
| 2865 | Comms repair kit |
| 2866 | Main Relief Valve cum unloading valve |
| 2867 | RECLAIM PANEL REPAIRKIT |
| 2868 | 4\\" digital display |
| 2869 | Hyperbearic Lights |
| 2870 | Latch mechanism |
| 2871 | Chineese finger |
| 2872 | Hoist |
| 2873 | SDC anodes |
| 2874 | SDC supporting frames |
| 2875 | Repair kit for spooling mechanism |
| 2876 | Wire lock compound |
| 2877 | Wire lubrication Compound |
| 2878 | Brake Pad |
| 2879 | Counter Sensor |
| 2880 | Pulleys |
| 2881 | Seal kit set |
| 2882 | Solenoid Valve Assy |
| 2883 | Needle Valve and Quarter turn Valve |
| 2884 | Tescom Regulator |
| 2885 | Biox and Fittings |
| 2886 | Extinguisher Refil |
| 2887 | Valve repair kit |
| 2888 | Valves |
| 2889 | Bush, Rod and O-ring set |
| 2890 | 5 Pin Mash Marine |
| 2891 | U/W Radio Repair Kit |
| 2892 | Helium radio repair kit |
| 2893 | Hyper Baric Paint |
| 2894 | Hyper Baric Paint |
| 2895 | Marine Paint |
| 2896 | O- Rings |
| 2897 | Inter Lock device |
| 2898 | Cassion Guage 240BAR |
| 2899 | 1 1/4 inch Ball Valve |
| 2900 | 1 1/4 inch 3 way Ball Valve |
| 2901 | BIBS single hose |
| 2902 | Amron 2825A Radio` |
| 2903 | DDCDisplay Monitor |
| 2904 | Intercom System |
| 2905 | Repair Kit |
| 2906 | Biox 15 Litre |
| 2907 | BIBS Repair Kit |
| 2908 | Brass Nut |
| 2909 | Neoprene Gasket Set |
| 2910 | O rings |
| 2911 | Valves |
| 2912 | Valves |
| 2913 | HP GDP hoses |
| 2914 | Hygrometers |
| 2915 | Fans of CO2 scrubbers |
| 2916 | Indicator lamp with holder |
| 2917 | 16 A fuse with fuse base |
| 2918 | PCB for indicator lamp |
| 2919 | Valves |
| 2920 | Potentiometers |
| 2921 | KW meter |
| 2922 | Overload switches |
| 2923 | Heater element with thermostat |
| 2924 | Canty lights |
| 2925 | Potentiometer |
| 2926 | HCU & ADDITIONAL HCU |
| 2927 | Fire Pfoof Fabric Pillow Blanket and Bed Sheet |
| 2928 | Repair Kit |
| 2929 | Hyperbaric Matress |
| 2930 | DDC flow meters |
| 2931 | 110 V contactor |
| 2932 | Remote starter |
| 2933 | Valve repair kit |
| 2934 | O ring |
| 2935 | Cable and connectors |
| 2936 | Hyperbaric paint. |
| 2937 | Hyperbaric paint. |
| 2938 | Relief valve service kit |
| 2939 | Gas Adaptor |
| 2940 | Quick connectors |
| 2941 | Quick connectors |
| 2942 | 2.5\\" Pressure gauges |
| 2943 | Brass Nut |
| 2944 | BIBS dump valves |
| 2945 | Hyperbaric camera |
| 2946 | BIBS pannel QRC |
| 2947 | BPR REGULATOR REPAIRKIT |
| 2948 | TESCOM REGULATOR REPAIRKIT |
| 2949 | TESCOM REGULATOR |
| 2950 | O' RING |
| 2951 | CHAMBER CONTROL PANEL REPAIRKIT |
| 2952 | BIBS REPAIRKIT |
| 2953 | COMMUNICATION SYSTEM REPAIRKIT |
| 2954 | HELIUM SCRAMBLING SYSTEM REPAIRKIT |
| 2955 | Pump repair kit |
| 2956 | Corblin compressor radiator |
| 2957 | VALVES REPAIRKIT |
| 2958 | WIPER RING OF OIL WIPER |
| 2959 | VEE BELT DRIVE REPAIRKIT |
| 2960 | COMPRESSOR FRESH WATER COOLING (RADIATOR) SYSTEM REPAIRKIT |
| 2961 | LP DIAPHRAGMS ASSEMBLY |
| 2962 | V – BELT |
| 2963 | PISTON RING |
| 2964 | PRESSURE SWITCH. |
| 2965 | RADIATOR COOLER MOTOR |
| 2966 | STARTER PANEL REPAIRKIT |
| 2967 | Compressor oil |
| 2968 | Water indicater port |
| 2969 | SEALS,O-RINGS& REPAIRKIT |
| 2970 | FINAL SEPARATOR FILTER CARTRIDGE |
| 2971 | FILTER CARTRIDGE/DRYER SYSTEM |
| 2972 | AUTOMATIC CONDENSATE DRAIN REPAIRKIT |
| 2973 | BAUER COMPRESSOR OIL SC AP-100. |
| 2974 | 2 NOS SAFTEY V/V AND 8 NOS SERVICE KIT |
| 2975 | TEMPRATURE/PRESSURE SENSORS |
| 2976 | PISTON RING |
| 2977 | CONDENSATE DRAIN KNOB |
| 2978 | CARTRIDGE SECCANT |
| 2979 | CONDENSATE DRAIN MAINTENANCE KIT |
| 2980 | CARTRIDGE MULTIPLEX |
| 2981 | VALVE BLOCK GASTIGHT MAINTENANCE KIT |
| 2982 | CARTRIDGE NON-RETURN VALVE |
| 2983 | SECCANT REGENERATION UNIT MAINTENANCE KIT |
| 2984 | HP and LP hoses |
| 2985 | Wire lock compound |
| 2986 | Repair kit for winch brake drum |
| 2987 | Hydraulic oil filter |
| 2988 | Gasket set |
| 2989 | Hardware |
| 2990 | Repair Kit for SDS hydraulic Pump |
| 2991 | Seal kit of Hydraulic cylinder |
| 2992 | Repair kit for starter unit |
| 2993 | Hyperbaric camera |
| 2994 | Comm service kit |
| 2995 | Comm service kit (HE) |
| 2996 | Cylinder valve |
| 2997 | Pressure gauge |
| 2998 | Hydraulic Hose |
| 2999 | Wire counter unit |
| 3000 | Service kit, under water search camera |
| 3001 | Webbing Strops 2 ton 2 mtr long |
| 3002 | Gasker and hardware set |
| 3003 | Repair kit for Hydraulic motor of winch |
| 3004 | Digital Video Recorder |
| 3005 | Valve repair kit, 10 nos Regulator repair kit 05 nos |
| 3006 | Hydraulic Hose |
| 3007 | Hydraulic tank |
| 3008 | M S Pipe |
| 3009 | Winch wire pulley |
| 3010 | Regulators |
| 3011 | 17Steel wire rope (Non roating type ) 17mm dia |
| 3012 | SERVO OMD113 |
| 3013 | PANEL AND CONTROL SYSTEM REPAIRKIT |
| 3014 | Solenoid valve |
| 3015 | Fabricated structure of cursor asembly with guide rail |
| 3016 | Hydraulic Motor Driven Winch unit |
| 3017 | Fabricated unit for Moonpool railing |
| 3018 | Seamless Tube (SS 316) |
| 3019 | SS 316 end fitting |
| 3020 | Filter element for Tank |
| 3021 | Paint |
| 3022 | Fabricated frame |
| 3023 | Hydraulic Hoses |
| 3024 | Hydraulic motor for Winch unit |
| 3025 | PVC Clamps |
| 3026 | Repair kit for Trolley and Guide weight starter |
| 3027 | O RING SEALS OF GUIDE WEIGHT&MAIN WINCH HYDRAULIC TANK VALVES |
| 3028 | BRAKE BAND AND DISC SPRING |
| 3029 | LOAD MATE MOTOR REPAIRKIT |
| 3030 | MOON POOL HATCH RUBBER COAMING |
| 3031 | SOLENOID VALVE |
| 3032 | TUP HYDRAULIC MOTOR REPAIRKIT |
| 3033 | SEAL,GASKET,MOTOR & PUMP REPAIRKIT |
| 3034 | HYDRAULIC PRESSURE GAUGE |
| 3035 | VALVES REPAIRKIT |
| 3036 | TROLLEY HYDRAULIC COMPONENTS REPAIRKIT |
| 3037 | TROLLY RAIL |
| 3038 | AUTO UMBLICAL PAY IN/ PAY OUT SYSTEM |
| 3039 | 2 NOS, 2\\" HOSE 20 BAR WP WITH SS END CONNECTION |
| 3040 | HYDRAULIC VALVES |
| 3041 | HYDRAULIC HOSES WITH SS END FITTING |
| 3042 | TROLLEY TRACK |
| 3043 | TUP CLAMPING MACHANISM REPAIRKIT |
| 3044 | GREASING NIPPLE |
| 3045 | HYDRAULIC GAUGES |
| 3046 | TEFLON COUPLING OF TROLLEY OF MOTOR&PUMP |
| 3047 | ELECTRICAL CABLE |
| 3048 | SERVO HYD.OIL SYSTEM 68 |
| 3049 | Sealing Ring |
| 3050 | Talk Back speaker and amplifier |
| 3051 | PRESSURE SWITCH |
| 3052 | PNEUMATIC MOTOR REPAIRKIT |
| 3053 | TROLLEY PNEUMATIC HOISTING LP TANK ACCESSORIES |
| 3054 | Spooling Device |
| 3055 | Bushing |
| 3056 | Wire lock compound |
| 3057 | Wire lubrication Compound |
| 3058 | Seal kit set |
| 3059 | Winch Drum Repair kit |
| 3060 | Paint |
| 3061 | Operating levers |
| 3062 | Guide weight winch control panel |
| 3063 | SAECO valve repair kit |
| 3064 | Reclaim Filters |
| 3065 | BPR service kit |
| 3066 | Reclaim service kit |
| 3067 | O2 service kit |
| 3068 | Recliam unit major service kit |
| 3069 | O rings and seals |
| 3070 | Scrubber fan |
| 3071 | LP Air filters |
| 3072 | O2 solenoid valve |
| 3073 | Haskell pumps |
| 3074 | Haskell spool drives |
| 3075 | Oxygen orifice |
| 3076 | Haskell Air regulator |
| 3077 | Flexible hoses |
| 3078 | Air filters |
| 3079 | No flow sounder |
| 3080 | Reclaim service kit |
| 3081 | Pipe clamps and ferauls |
| 3082 | Reclaim repair kit |
| 3083 | Drain valves |
| 3084 | Scrubber filter pads |
| 3085 | Filter element |
| 3086 | Flow meter |
| 3087 | Flow switch |
| 3088 | Gearing and travelling rods of winch bent |
| 3089 | Hydrogen Burner |
| 3090 | U/W camera and monitor |
| 3091 | Tilt meter |
| 3092 | Water flow meter |
| 3093 | Electrical junction box. Material - Stainless steel |
| 3094 | Dome type regulator |
| 3095 | Pressurisation and exhaust valve |
| 3096 | Pneumatic motor gear assembly |
| 3097 | Submarine rescue Life Support hose - Non collapsible 300 mtr - 02, 100 mtr - 01 |
| 3098 | SLIP RING |
| 3099 | 1 QTY HIGH FLOW PILOT REGULATOR AND 10 NOS REPAIR KITS OF VALVES |
| 3100 | O RINGS. |
| 3101 | VALVES REPAIRKIT |
| 3102 | BERAINGS AND BUSHES |
| 3103 | O RING |
| 3104 | O RING. |
| 3105 | O RING. |
| 3106 | SRB UPPER HATCH CLOSING MECHANISM AND EQUALISTION VALVES REPAIRKIT |
| 3107 | RUBBER GASKET & VALVES REPAIRKIT |
| 3108 | CLUTCH PADS, BEARING AND BUSHES |
| 3109 | LIGHT AND CAMERA DISTRIBUTION PANEL REPAIRKIT |
| 3110 | BATTERIES |
| 3111 | COMMUNICATION SYSTEM REPAIRKIT |
| 3112 | HYPERBARIC PAINT.(1 LS= 20SQ MTRS.) |
| 3113 | MARINE PAINT.(1 LS= 20SQ MTRS.) |
| 3114 | WATER FLOW METER REPAIRKIT |
| 3115 | PRESSURELUBE COMPOUND 20 LTR AND WIRELOCK |
| 3116 | END FITTING |
| 3117 | SEALS AND BUSHES |
| 3118 | PAINT SCHEME |
| 3119 | HYPERBARIC CASING REPAIRKIT |
| 3120 | SRB UMBILICAL AND EXHAUST HOSE WINCH GEAR ASSEMBLY REPAIRKIT |
| 3121 | WEBBING STROP |
| 3122 | SHOES FOR BLOCK BRAKE |
| 3123 | COMPENSATING TANK MAN HOLE RUBBER GASKET |
| 3124 | WINCH WIRE WITH THIMBLE EYE |
| 3125 | SRB JUNCTION BOX |
| 3126 | BROKEN FENDERING ARRANGEMENT |
| 3127 | WEIGHT WHEELS AND BREAK SYSTEM REPAIRKIT |
| 3128 | SRB UMBILICAL AND EXHAUST HOSE REPAIRKIT |
| 3129 | VALVES REPAIRKIT |
| 3130 | WORKING CHAMBER TO AIR LOCK CHAMBER VIEWPORTS |
| 3131 | BEARING,MOTOR AND STARTER REPAIRKIT Please Enable Macros to View BoQ information |
AI Tender Summary
Tender Timeline
Jul 08, 2026
11:30 IST
Tender Published
Tender notice published.
CompletedJul 29, 2026
17:00 IST
Bid Submission Deadline
Online submission via eProcurement portal.
Upcoming · 12 daysJul 30, 2026
Bid Opening Date
Technical bids will be opened and evaluated.
Upcoming · 13 daysTender Documents
Download All (ZIP) ↓
Disclaimer
We takes all possible care for accurate & authentic tender information. However users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender