Tender For Certain Repair/Maintenance To Otm Accn In Area A-2 Of Age B/R-I Under Ge (W) Jalandhar Cantt
Tender Value
45 Lakhs
Estimated cost
Bid Submission
27 Jul 2026
18 days left
EMD
90000
Bank guarantee accepted
Document Fee
500
Non-refundable
Tender Type
Online
Tender Overview
Organization
Tender ID
Competition Type
NCB
Bidding Type
Tender
Location / State
Jalandhar → Punjab
EMD Exemption
Available
Quantity
Not Available
Website
Contact Person
Address
Project Description
Tender For Certain Repair/Maintenance To Otm Accn In Area A-2 Of Age B/R-I Under Ge (W) Jalandhar Cantt
BOQ
| Sl. No. | Item Description |
| 1 | Demolition of cement concrete in ground floor and paving n.exc 15 cm thick (below or above ground level complete . |
| 2 | Demolition of brick or stone masonary built in cement mortar complete |
| 3 | Taking down cement plastering on stone wall/brick wall etc including racking out of joints hacking for key scrubbing down with water etc. |
| 4 | M&L brick work with sub-class 'B' bricks, straight or curved on plan exceeding 6 M mean radius built in CM 1:6. |
| 5 | M&L brick work with sub class B bricks, straight or curved on plan to any radius in half brick thick wall built in CM 1:4 complete all as spd and directed. |
| 6 | M&L Cement concrete type D 2, 1:4:8 (using 40 mm graded stone aggregate) in sub base of flooring, hard standing, Manhole, drain etc. |
| 7 | M&L 75mm thick PCC 1:3:6 type C2 (using 40mm graded stone aggr) as in plinth protection/path finishing the surface even and smooth without using extra cement complete all as spd and directed. Note : Plinth protection shall be laid in (1:20) slope. The concrete shall be laid at a stretch not exceeding 3metre in length. Joint gap between adjoining slab, at corners and at junctions of walls shall not exceed 10mm in width and shall be sealed with mastic filling i.e. one part of bitumen 85/ 25 grade mixed with 3 part of sand. Top surface of concrete shall be finished even and smooth without using extra cement. Joints shall be provided at not more than 3 metre interval at corner and as junction of walls. |
| 8 | M&L machine pressed precast coloured concrete coloured interlocking paver blocks any shape and size confirming of IS 15658: 2006 of 60mm thick , M-35 laid and jointed with grey cement and pigment. |
| 9 | M&L for 25mm thick Sand filling under floors or in foundations including watering and consolidation. |
| 10 | M&L for Plain Cement Concrete Type B1 1:2:4 (using 20 mm graded stone aggregate) cast in situ in kerbs or mud stops, rounded or chamfered on edges of paving blocks as directed including use and waste of form work. |
| 11 | M&L 10mm thick rendering in CM 1:3 on brick/concrete surface as in ceiling and finishing the surface even and smooth with out using extra cement. |
| 12 | M&L 15mm thick rendering on wall in CM 1:4 with appropriate WPC as per manufacturer's information from SIKA Plastocrete Plus/FOSROC/ DR Fixit/ STP/CICO on brick/concrete surface,finished even and smooth without using extra cement. |
| 13 | M&L 15mm thick rendering on wall in CM 1:6 on brick/concrete surface and finishing the surface even and smooth with out using extra cement. |
| 14 | Demolition of reinforced cement concrete of any description and in any position not otherwise specifically provided for. |
| 15 | Formwork to soffits of suspended slabs such as roof slabs, floor slabs, landings and similar work not exceeding 200mm thick (Horizontal or sloping) rough finished surfaces of concrete. |
| 16 | M&L for Reinforced cement concrete type B1 1:2:4 (20 mm graded aggregate) (nominal mix) in Slabs supported on walls, beams and columns in floors, roofs, landings, balconies, canopies, deck slabs and in shelves and the like. |
| 17 | M&L mild steel deformed bars 8mm dia and over cut to length bent to shape required including cranking bending and binding with and including mild steel wire annealed not less than 0.9 mm dia or securing with clips confomring to Gd I IS-432. |
| 18 | Demolition of floor hearth or wall tiling including cement mortar bedding (not backing ) removing serviceable tiles to store and rubbish of the premises. |
| 19 | M&L coloured Glazed ceramic tiles in vertical surface 350x 250x 7 mm/ 450X 350X 7mm thick set and jointed in neat cement slurry and pointed in white or colour cement to match the surface over 10 mm thick cement plaster in CM 1:4. |
| 20 | M&L Non skid Coloured ceramic tiles 7 to 8 mm thick (squre or rectangle) area of each tile exceeeding 0.11 SqM but not exceeding 0.18 SqM in floors etc, set and jointed in neat cement slurry and pinted in white or coloured cement to match with including 15mm thick screed bed in CM 1:6. |
| 21 | M&L vitrified ceramic tiles 10mm thick light shade (square/rectangle) polished area of each tiles n exc .36 sqm in floor etc set and jointed in neat cement slurry and pointed in white or coloured cement to match over 15mm thick screed bed in CM 1:6. |
| 22 | M&L vitrified ceramic tiles 10mm thick light shade (square/rectangle) polished area of each tiles exceeding 0.42 sqm but not exceeding 1.00 sqm in floor etc set and jointed in neat cement slurry and pointed in white or coloured cement to match over 15mm thick screed bed in CM 1:6. |
| 23 | M&L vitrified ceramic tiles 10mm thick light shade (square/rectangle) polished area of each tiles n exc. 36 sqm in skirting etc set and jointed in neat cement slurry and pointed in white or coloured cement to match over 10mm thick screed bed in CM 1:4. |
| 24 | Demolition of Stone slabs and tiles of any description or thickness in floors, aprons etc. laid bedded and pointed in any morter. |
| 25 | M&L Machine cut kota stone slab flooring 20-25mm thick over 20mm thick cement screed bed in CM 1:6 laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing upto mirror finished complete. |
| 26 | M&L Machine cut kota stone slab flooring 20-25mm thick as in skiritng, riser of steps etc laid over 10mm thick cement plaster in CM 1:4 laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing upto mirror finished complete. |
| 27 | M&L Absolute/Pure black Granite (of any type) work (table rubbed and polished) for wall lining (veneering to wall) 12mm to 20 mm thick in 15mm thick cement mortar (1:3) and pointing with white cement (1:2) using marble dust with admixture of pigment to match with shade of granite complete all as specified and directed. |
| 28 | Rounding/moulding to edges of Kota stone slabs, marble stone, granite stone slabs one edge, such as in steps, cooking platform, and other similar situations etc. |
| 29 | M&L Chequered cement concrete tiles 30cmx30cmx25 mm thick set and jointed in neat cement slurry and pointed in white or colour cement to match the surface over 10 mm thick cement plaster in CM 1:4. |
| 30 | Demolition of cement concrete above ground floor and paving exc 15 cm thick below or above ground level complete. |
| 31 | M&L for 15mm thick rendering in 1:3 CM with using appropriate WPC as per manufacturer's information from SIKA Plastocrete Plus/FOSROC/DR Fixit/STP/CICO on brick/concrete surface, finished even and smooth without using extra cement. |
| 32 | M&L Plain Cement Concrete Type A0 1:1.5:3 (using 12.5 mm graded stone aggregate). |
| 33 | M&L for priming surfaces with bituminous primer polymerised primer oil based @ 0.30kg per Sqm. |
| 34 | M&L for applying coat of industrial bituminous 85/25 @ 1.20 Kg per squqre mtr including cleaning surfaces. |
| 35 | M&L APP based polymeric membrance minimum weight not less than 3.0kg/sqm and minimum 3mm thick reinforced with polyster non wove fabric (wt not less than 150gms/sqm) land on primed surface by forced application(Complete surface sealed by gas flame) with over lap of 15 cm complete all as specified and directed complete all as spd and directed. |
| 36 | M&L 25mm thick cement concrete flooring type B-1, 1 :2 : 4, using 20 mm graded stone aggregate finishing cement concrete surface even and smooth without using extra cement. |
| 37 | M&L Cement concrete type E-2, 1:5:10 using 40mm graded brick aggregate in foundations filling and mass concrete as in sunken floor. |
| 38 | Cutting holes into or through brick walls built, in cement mortar Superficial area N.exc 150 sq. cm upto 23cm of depth of wall for repairing of existing spout pipe. |
| 39 | M&L for 40mm dia GI pipe,med grade beveled cut at both ends by making hole in walls sunken portion aprox above the RCC slab and ceiling finished the hole with cement plaster 1:2 to match with existing surface complete etc.(Measured for cutting holes shall be paid in concerned sch item). |
| 40 | Taking down chowkats or frames with shutters (without taking of shutter from the frame) of any description alongwith fittings n.exc 1.5sqm each. |
| 41 | Taking down chowkats or frames with shutters (with out taking of shutter from the frame) of any description alongwith fittings exc 1.5sqm n.exc 4 sqm each. |
| 42 | Taking down shutters any description exc 1 sqm but n.exc 2sqm each and all as specified and directed. |
| 43 | S&F pressed steel door frame with one or more rebate including necessary fixing lugs, hinges, lock stricking plate of size 105 x60mm. |
| 44 | S&F pressed steel door frame with one or more rebate including necessary fixing lugs, hinges, lock stricking plate of size 125 x60mm. |
| 45 | M&L for PCC Type B0-1:2:4 using 12.5mm graded aggregate as in filling of pressed steel frame, hold fasts and similars articles. |
| 46 | Cutting holes in brick walls in cement mortar for inserting holdfasts and making good dismantled portion in cement mortar 1:3 or cement concrete 1:2:4 Type B-1 as required built in cement motar in brick wall depth of embedded portion of holdfast exc half brick but n exc one brick. |
| 47 | S&F 2nd class hardwood 35mm thick Plain, framed, panelled shutters (any number of panels), with panels of timber flat on both sides (feather edged), or of veneered particle board medium density, wood particle board with commercial face veneers supplied and fitted to chowkats. |
| 48 | S&F 2nd class hardwood glazed and skelton door shutters 35 mm thick divided into squares open rebated and prepared to receive glass, gauge etc edges of framing plain, chamfered, rounded tfitted with mltred beads for securing glass etc, size of members as specified in SSR Pt 1 section 8 clause 8.20 (b) supplied and fitted to chowkats with plain, chamfered or rounded mited and rebated bars any numbers. |
| 49 | Solid PVC door frame of size 50 x 47 mm made out of 5 mm plain colour PVC sheet reinforced with MS square tube. |
| 50 | S&F factory made solid panel pvc door shutter 30mm thick (style) consisiting of frame made out of M.S. Tubes for top & bottom rails M.S. frame shall be covered with heat moulded plain colour PVC `C' channel having a PVC sheet strip of 20mm width struck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail, panelling of plain colour PVC sheet to be fitted in MS frame welded/sealed to the stiles & rails with suitable PVC sheet beading, and joined together with solvent cement, fixing in the frame at the site as per specification & drawing. |
| 51 | Steel window/ventilator 1.25 mm thick Box type ERW hollow P section of size 60mm x 25 mm single rebated comprises skelton shutter ERW Sec 50 MM x 20 mm and 1 mm thick and two openable leaf consisting two Nos sash bar of T-section 20 mm x 3mm complete welded to frame with one vertical mullion of ERW box type T section of size 60mm x 25 mm and 1.25 mm thick including cuttings holes and making good dismantled portion in PCC (1:2:4) type B-1, including shop coat primer and following fittings welded to shutters:-(i) Hold fasts 150 mm long,12mm x 3mm made to shape -04 Nos (ii) Handle of Z sec 20mm x 25mm , 100mm long per leaf -1 Nos (iii) MS tower bolt 150 mm long per leaf -2 Nos (iv) Z sec 20mm x 25 mm , 100 mm long stopper per leaf -1 No (v) Cleat 55 mm long of hollow square 15mm x 20mm x 63 mm welded to hinges per leaf -01 No (vi) MS pintal hinges of size 75mm x 12 mm per leaf -02 Nos (vii) Fabrication and fixing arrangement complete. |
| 52 | All as per description of item No 51 above but glazed shutter. |
| 53 | S&F framed work such as grills & gates, gratings with ends of bars shouldered on forged in spickes, framed guard bars, barred iron doors, ladders, framed balusters, walk ways, rallings, framework of water tanks and similar work conforming to Fe-290 Gde-E-165. |
| 54 | S&F Galvanised mild steel wire cloth, 0.56mm nominal dia of wire and avg erage with aperature 1.18 mm fixed with tinned tacks, or galvanised wire staples. |
| 55 | S&F 3mm thick sheet glass ordinary quality and glazing with oil putty in square n.exc 0.50 sqm in each pane complete all as specified. |
| 56 | S&F Butt hinges, medium weight cold rolled 100 mm size ISI marked. |
| 57 | S&F for Butt hinges, extruded aluminium alloy with galvanised mild steel hinge pin, anodised and fixed, type B-21. |
| 58 | S&F aluminium anodised barrel tower bolts of extruded section 150mm long all as specified. |
| 59 | S&F Extruded aluminium alloy handles fabricated type anodised 150mm size. |
| 60 | S&F aluminium alloy anodised sliding door bolts 250 mm long with hasp, staple (bolt type)and fixing clips of sheet cast or extruded section and fixing bolts and sliding bolts of extruded sections as specified. |
| 61 | S&F 300 mm mild steel ordinary rat tail rod pattern springs including roller and roller plate complete. |
| 62 | S&F Floor door stopper of aluminium alloy body and tongue, anodised, with hard drawn steel spring, fixed in floor 150 mm. |
| 63 | S&F Powder Coated Anodised aluminium frame for partition work,doors,windows, ventilators with one or more rebates including joining cleat for fixing etc. complete all as specified. |
| 64 | S&F powder coated of any colour (Thickness or powder coating not less than 50 micron) Anodised aluminium door shutters, aluminium section weighing 0.55 kg/ m including necessary joining cleats, glazing clips, ruber neoprene packing, handles 2 Nos in each door, hinges, anodised aluminum snap beading screws etc. complete all as specified. |
| 65 | M&L Powder coated aluminium (minimum thickness of powder coating 50 micron) for sliding window shutters including providing and fixing roller, three track system, locking arrangement fittings wherever required including the cost of EPDM rubber/neoprene gasket required (Fittings shall be paid for separately) with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS:1285, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing/ paneling, C.P. brass/ stainless steel screws where necessary all complete as per architectural drawings and directions. |
| 66 | S&F in repair replacement Cast iron body door closer hydraulically regulated, designation No 3 universal type suitable for door shutters of 851 to 1000mm in width and of weight between 61 to 80 Kg complete all as spd and directed. |
| 67 | S&F in repair double action floor spring hydraulically regulated made up of minimum 1.25 mm thick aluminium alloy sheet foundation box, main body with stainless steel cover, governing pivot made of brass , other parts made of mild steel heavy duty and fixed complete all as spd. |
| 68 | M&L for 4.80mm thick sheet glass ordinary quality glazing with oil putty in squares not exceeding 0.50 Sqm in each pane complete all as specified and directed. |
| 69 | S&F for solar control film 25 micron reflective type sticked to glass pane as per instructions of manufacturers. |
| 70 | Taking down top assembly (except curtain and side bracket) of rolling shutter of area not exc. 10 Sqm each, push pull or manual type and re-fixing the same in same position after necessary repairs such as cleaning, oiling, greasing, replacement of rusted nuts and bolts, including welding / grinding as require for proper and smooth function including necessary oiling / greasing, welding, etc after cleaning of the both side guided channels etc. complete all as directed. |
| 71 | Taking down top assembly (except curtain and side bracket) of rolling shutter of area exc. 10 Sqm but n.exc 20Sqm each, gear operated and re-fixing the same in same position after necessary repairs such as cleaning, oiling, greasing, replacement of rusted nuts and bolts, including welding / grinding as require for proper and smooth function including necessary oiling / greasing, welding, etc after cleaning of the both side guided channels etc. complete all as directed.Note :- (for item No 70 & 71)Unserviceable spare part such as suspension shaft, spring, ball bearing will be replace with new one and same shall be measured and paid separtely as supply only under respective items |
| 72 | Supply only steel ball bearing suitable for rolling shutter for smooth functioning of rolling shutter of any size or type all as specified and as directed. |
| 73 | Supply only Hot rolled mild steel round pipe any dia as in suspension shaft for rolling shutter for smooth functioning, cut to size including necessary drilling / grinding etc complete. |
| 74 | Supply only Mild steel spring suitable for rolling shutter of any size for smooth functioning, all as specified and directed. |
| 75 | Supply only 1.0 mm thick Steel rolling shutters, with out ball bearing, as specified including top cover, anchoring rod, hasp and staple and one shop coat of primer; erected in position as indicated, complete push pull or manual type including dismantiling complete pull push or manual type all as sped and directed. |
| 76 | All as per description of item No 75 above but gear operated type with bevel gear box and crank handle. |
| 77 | S&F in repair for Safety lever locks mild steel with 4 levers for rolling shutters complete all as spd and directed. |
| 78 | Demolition of wall and ceiling boards (fibre, pulp, insulation, etc.) or insulation boards/slabs/ blankets, any thickness, including cover fillets. |
| 79 | S&F for 4 mm thick of size 600x600mm HSPC (high pressure Steam Cured) pre-primetered self embossed, textured designer board E-Board Classic to be fixed GI powder coated grid/section size 600mmx600mm with main runner 38x24x0.9mm thick ,cross tee 28.6x24x0.9 mm and wall angle 19x19xo.9 mm duly suspended with Hangers 6 mm dia. G.I. (upto 1200mm length) adjusting level fixed to roof slabs by means of ceilling cleats made out of G.I. flat 40 x 3 mm size 60mm long and expansion hold fasteners 12.5mm dia. 40mm long complete all as specified. |
| 80 | M&L for PVC Wall Lining consisting of 5mm thick wood grain printed PVC sheet inclusive of solvent cement and fixing at site on PVC frame as per specifications and drawing. |
| 81 | M&L for 5mm thick PVC sheet fillet of width 35mm for wall paneling inclusive of fixing on to wall to make PVC Frame as per specification and drawing. |
| 82 | Taking up or down 15 mm bore steel tubing and connection including cleaning for re-fixing or removal to store complete all as specifed and directed. |
| 83 | Taking up or down 20 mm bore steel tubing and connection including cleaning for re-fixing or removal to store complete all as specifed and directed. |
| 84 | S&F 15mm bore GI tubing medium grade fitting complete to wall and ceiling or laid in floor complete all as specifed and directed. |
| 85 | Refixing 15mm old GI tubing and connections in new or old position (Walls, ceiling, floors, etc.) |
| 86 | S&F 20 mm bore GI tubing medium grade fitting complete to wall and ceiling or laid in floor complete all as specifed and directed. |
| 87 | Refixing 20 mm old GI tubing and connections in new or old position (Walls, ceiling, floors, etc.) |
| 88 | Supplying and laying of 16 mm CPVC pipes SDR 11 & Plain CPVC SDR 11 fittings on walls/ceiling or laying in floors complete all as specified. |
| 89 | S&F 16 mm CPVC Brass Elbow. |
| 90 | S&F 16 mm CPVC Brass Tee. |
| 91 | S&F 16 mm CPVC union. |
| 92 | Cutting chases, pinning in making good to facings where reqd and pointing in cement mortar 1:3 to ends or edges of shelves , for water tubing etc and making good, cutting exc 10cm girth but not exc 20cm girth in stone walls. |
| 93 | Dismantiling of water tanks of capacity exc 250 & n exc 500 ltrs incl all necessary fittings complete. |
| 94 | Dismantiling of water tanks of capacity exc 500 & n exc1000 ltrs incl all necessary fittings complete. |
| 95 | Dismantiling of water tanks of capacity exc 1000 & n exc 2000 ltrs incl all necessary fittings complete. |
| 96 | S&F 500 ltrs PVC rotational moulded polyethylene water storage tanks double layer made (cylindrical vertical with closed top ) hoisted and fixed in position all as spd. |
| 97 | S&F 1000 ltrs PVC rotational moulded polyethylene water storage tanks double layer made (cylindrical vertical with closed top ) hoisted and fixed in position all as spd. |
| 98 | S&F 2000 ltrs PVC rotational moulded polyethylene water storage tanks double layer made (cylindrical vertical with closed top ) hoisted and fixed in position all as spd. |
| 99 | S&F 20mm Gun metal, globe or gate valves, with iron wheel head, screwed both ends for iron pipe and fixed in repair. |
| 100 | S&F ball float valve PTMT with epoxy coated aluminimum rod for 20 mm bore pipe high pressure with polythelene high density float and complete screwed for iron pipe. |
| 101 | S&Fin repair 15mm dia Bib taps cast copper alloywith fancy type chromium lated crutch or butterfly handle screwed down, scewed for iron pipes or for brass ferrule. |
| 102 | S&F 15mm dia Brass stop valves chromium plated, fancy type with long shank and cup concealed type screwed down, highpressure with crutch or butterfly handle, screwed both ends for iron pipe or for unlori as specified and fixed in repairs. |
| 103 | S&F 15mm dia Brass stop valves chromium plated, fancy type with long shank and cup screwed down, highpressure with crutch or butterfly handle, screwed both ends for iron pipe or for unlori as specified and fixed in repairs. |
| 104 | S&F in repair 15mm dia fancy type pillar taps cast copper alloy with capstan heads chromium plated scewed down high pressure with long scrwed shanks and fly nuts screwed for iron pipes. |
| 105 | S&F 600x450 bevelled edged looking mirror 2mm thick of selected quality glass, mounted on 4 mm thick PVC sheet and with aluminnium frame work fitted with chromium plated brass screws and cup washers including taking old one. |
| 106 | S&F in repair Vitreous china wash hand basin (550X400mm) white, flat back excluding taps, including brackets &32mm waste cuppling complete all as specifed and directed. |
| 107 | S&F Vitreous China Water closet (Squatting pattern) \\"Orissa Pattern\\" size 580x 440 mm white with 'P' or 'S' trap, front or back inlet and foots rests any pattern (excluding flusing cistern and flush pipe) in repairs complete. |
| 108 | S&F Vitreous China wash down Water closet pan (pedestal pattern) \\"with plastic water closet seat cover closed pattern with flat bottom and cover and mild steel chromium plated or aluminised hinging divice (excluding flusing cistern and flush pipe) in repairs complete. |
| 109 | S&F 10 Litre PVC valveless syphonic action flushing cistern low level white with inlet ball valve, float and handle including brackets and flush pipe of polyethylene of low or high density or PVC 32 mm dis for low level cistern in repairs. |
| 110 | Vitreous China urinals, hallf stall urinals (back or corner wall type), complete including providing and fixing plugs, bedding urinal against wall in cement mortar 1:2, securing urinal to plugs with and including 60mm long brass screws, pointing around urinal back in cement, fixing automatic flushing cistern with brackets, flush pipe, grating and Union for discharge pipe. (Exclusive of fixing supply pipe to flushing cistern, trap and waste pipe). |
| 111 | M&L 75mm PVC (SWR) floor trap , plain with CP grating including jointing with solvent cement complete all as spd and directed. |
| 112 | S&F in replacement CP grating 125mm dia circular of approved make and fixing with cement mortar 1:3 on Nahani Trap or floor trap complete all as specified. |
| 113 | S&F in replacement CP Jet for EWC including flexible pipe complete all as specified. |
| 114 | S&F Health faucet (ABS body) mild steel chromium plated suitable for 15mm dia pipe with 1.25mtr long flexible tube and ABS wall hook including making connection and fixed in position complete in all respect as specified. |
| 115 | S&F 15mm PVC connection 450mm long with PTMT nuts of superior quality as specified. |
| 116 | S&F in toilet paper holder of brass chromium plated fixed to walls with brass screws. |
| 117 | Supply and fixed Soap dish, any type fixed to walls with plugs with chromium plated brass screws. |
| 118 | S&F for brass chromium plated Tubular towel rail, 20mm dia, D type, 60cm long between flanges etc complete all as spd and directed. |
| 119 | S&F brass chromium plated shower rose 125mm size complete all as spd and directed. |
| 120 | Taking down eaves gutters and rainwater pipes (any size or pattern), including all fittings, heads, shoes, bends, swan-necks, etc., including cleaning or refixing or removal to Store (measured overall as fixed along the centre line over fittings and accessories). |
| 121 | Dismantling of cast iron or reinforced concrete drain pipes of size 100mm dia, jointed in cement mortar and taking out of trenches, if required. |
| 122 | S&F 110mm PVC (SWR) pipes single socketed in any length with rubber ring joints, fixed to walls complete. |
| 123 | S&F 75mm PVC (SWR) pipes single socketed in any length with rubber ring joints, fixed to walls. |
| 124 | S&F110mm PVC (SWR) bends. |
| 125 | S&F75 mm PVC (SWR) bends. |
| 126 | S&F for PVC 110mm (SWR) vent cowl. |
| 127 | Dismantling of brick tiles single layer as in roof covering complete all as specified. |
| 128 | Taking down existing water proofing from roof slab and cleaning the roof slab incl scrapping of existing lose concrete from roof top and washing with water complete all as specified and directed. |
| 129 | Demolition of mud in roofs any thickness including plastering and leeping (whether full thickness removed or only a part thereof) all as specified. |
| 130 | Cleaning/Roughening surfaces of old concerete floor/roof by picking, sweeping clean and washing down with water to romove the dust etc complete all as spd. |
| 131 | M&L for PCC pedding with cement concrete type B-1, 1:2:4 (using 12.50mm graded stone aggregate) to top surface of slab in slop 1:40, finishing the surface even and smooth without using extra cement complete all as specified. |
| 132 | M&L 10mm thick rendering on top of roof slab in cement mortar 1:4 with using appropriate WPC as per manufacturer's information from SIKA Plastocrete Plus/FOSROC/DR Fixit/STP/CICO on brick/concrete surface, finishing the surface even and fair without using extra cement. |
| 133 | Providing and applying liquid Polyurea-PU based hybrid elastomeric water proofing membrane at existing/newly constructed roofs, RCC structure like basement raft, retaining wall, water retaining structure, tunnels/subways and bridge deck etc. in two or more coats. The product must have pot life of >90 mins., tensile strength > 12.6 Mpa, elongation of > 500% conforming to ASTM D 2370 & puncture resistance of >200 N as per ASTM E 154 with min. consumption of 1.5 Kg per sqm for 1.2mm DFT in two- three coats. The surface needs to be primed with water soluble self impregnated epoxy primer in two coats to be applied @ 200-250 gms/sqm/coat prior to Polyurea -PU application. Furthermor, (in case the substrate is not suitable) 15mm plaster is advisable for surface prepration before application of the water proofing membrane to avoid pinholes or functional difficulties of the system (Make - Asian Paints, BASF & SIKA). Note:- The application shall be done by the authorised applicator of the manufacture with a letter of proof stating the authenticity of the applicator firm. |
| 134 | M&L for repairing of RCC projections, chajjias, roof slab, facia etc in patches not exceeding 3 Sqm in each patch by necessary preparation. Scarpping, cutting, chiseling derusting and cleaning exposed reinforcement, surfaces of damaged, loose RCC surfaces and applying one coat of rust stop solution of approved make and filling the surfaces with cement concrete (1:1.5:3) using 12.5mm graded crushed stone aggreagates and reinforced with welded TMT bars/mesh (If Reqd) of weight exc 2 kg per sqm but n.exc 3kg/sqm with or without facia and finished with cement and sand motar (1:3) using coarse sand and thickness of R.C.C member n.exc 100mm including necessary form work and applying two coats of finishes to match with the existing surfaces in at any height complete all as specified and directed. (Note : Cost of formwork, TMT bars and welded mesh shall be deemed to be included in unit rate quoted by the contractor complete all as specified and as directed. |
| 135 | Dismantling asbestos cement (corrugated or semicorrugated sheets in roof coverings). |
| 136 | M&L for pre galvalume aluminium zinc coating GI based corrugated steel sheet 0.50 mm thick of any colour having tensile strength of 550Mpa as in roof covering/cladding to wll fixed with self tapping screws as specified. |
| 137 | M&L Pre-painted galvalume aluminum zinc coating GI based Plain steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws as specified. |
| 138 | Cutting chases, pinning in making good to facings where required and pointing in cement mortar 1:3 to ends or edges of landings, steps, cills, sunshades, shelves, lintels, etc. and cutting chases for concealed water tubing or concealed conduit wiring etc, and making good, cutting not exc 10 cm girth in brick wall. |
| 139 | M&L Providing cement concrete 1:2:4 type B-1 using 20mm graded aggregate) in roof kerbs or mud stops, rounded or chamfered on edges. |
| 140 | Dismantling of mild steel work of any description not other wise provided for. |
| 141 | S&F Roof trusses (framed), trussedpurlins, crane gantries, rails andfastenings and heavy bracket framing (Beam, tee, angle, channelor flat sections) includingdistance pieces, cleats etc.Fe 410 -W(Gde-E- 250) quality-A. |
| 142 | M&L for applying two coat of synthetic enamelled paint over one coat of pink primer including preparation of new wood surfaces of any description not otherwise described over 10 CM girth or width all as directed. |
| 143 | M&L for applying one coat of synthetic enamelled paint including preparation of old treated wood surfaces of any description not otherwise described over 10 CM girth or width all as directed. |
| 144 | M&L for applying two coat of synthetic enamelled paint over one coat of red oxide primer including preparation of new steel surfaces of any description not otherwise described over 10 CM girth or width all as directed. |
| 145 | M&L for applying one coat of synthetic enamelled paint including preparation of old decorated steel surfaces of any description not otherwise described over 10 CM girth or width all as directed. |
| 146 | M&L for applying white wash of 3 coats as in ceiling incl preparation newly plastered surfaces as specified and directed. |
| 147 | Material and labour for preparation of new plastered surfaces on walls and applying two coats of oil distemper over one coat of chalk whitening complete all as specified. |
| 148 | M&L for prepration of old decorated surfaces of walls, washing rubbing down and stooping of distempered and painted surfaces and applying one coat of oil bound distemper complete all as specified and directed. |
| 149 | Material and labour for preparation of new plastered surfaces on walls and applying two coats of cement base paint over one coat of cement primer complete all as specified. |
| 150 | M&L for prepration of old decorated surfaces of walls and applying one coat of cement base paint complete all as specified and directed. Please Enable Macros to View BoQ information |
AI Tender Summary
Tender Timeline
Jul 07, 2026
11:30 IST
Tender Published
Tender notice published.
CompletedJul 27, 2026
17:00 IST
Bid Submission Deadline
Online submission via eProcurement portal.
Upcoming · 18 daysAug 03, 2026
Bid Opening Date
Technical bids will be opened and evaluated.
Upcoming · 25 daysTender Documents
Download All (ZIP) ↓
Disclaimer
We takes all possible care for accurate & authentic tender information. However users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender