Tender For Repair/Maint Of Pump Sets, Control Panels And Connected Works Installed Under Ge Chennai
Tender Value
40 Lakhs
Estimated cost
Bid Submission
28 Jul 2026
18 days left
EMD
80000
Bank guarantee accepted
Document Fee
500
Non-refundable
Tender Type
Online
Tender Overview
Organization
Tender ID
Competition Type
NCB
Bidding Type
Tender
Location / State
Chennai → Tamil Nadu
EMD Exemption
Available
Quantity
Not Available
Website
Contact Person
Address
Project Description
Tender for Repair/Maint Of Pump Sets, Control Panels And Connected Works Installed Under Ge Chennai
BOQ
| Sl. No. | Item Description |
| 1 | NOTE FOR ITEM NOS 1 to 21 : Contractor shall obtain issue voucher duly mentioning MES No, type & capacity of motor/ pump, date etc. Upon completion of servicing/ rewinding / replacement of parts, necessary receipt voucher shall be obtained. The details of IV / RV shall be entered in MB during measurements. RAR/ FB payment will be paid based on IV/ RV only. No payment shall be effected for measurements without details of IV/ RV and contractor shall have no claim for payments disallowed on account of the same. Dismantling the monoblock pumpset any capacity after disconnecting suction and delivery pipes including electrical connection, transporting the pumpset any of capacity 0.5 HP to 2.5 HP to workshop for carryingout repairs/servicing and overhauling including greasing / oiling, replacement of wornout bushes, bolts and nuts etc including replacement of defective spares complete and including painting of pumpset after preparation of oil surface by scrapping, cleaning and apply two coats of synthetic enamelled paint with spray gun and writing the SM/MES No including suction and delivery pipe lines along with writing of the details of feeder lines with indication and detecting any repair in the pumpset after connecting, testing complete all as specified and as directed. Note: Spares will be measured and paid separately under relevant items. |
| 2 | Supply only the following spares sutable for monoblock pumpset of capacity upto 2.5 HP. (a) Ball bearings (drive end/ non drive end). |
| 3 | (b) Terminal Box. |
| 4 | (c) Terminal connector 3 phase |
| 5 | (d) Electro dynamically balanced bronze impeller. |
| 6 | (e) Gun metal bush |
| 7 | (f) Gland cup with bolts and nuts. |
| 8 | (g) Flange drilled of suitable size with bolts and nuts including rubber gasket. |
| 9 | (h) Rotor |
| 10 | (i) Automatic contactor for pressure release fitted in delivery pipe line complete |
| 11 | (j) Pressure water tank heavy duty fitted at pump in delivery pipe line complete |
| 12 | (k) Condenser of capacity 140/160 MFD. |
| 13 | M&L for rewinding of electric motor of any make of capacity 0.5 HP to 2.5 HP, by dismantling and removing the old burnt windings and rewinding for suitable gauge of enamelled copper wire and insulating with suitable class of insulation, varnishing complete including repairs to terminal box of motor, connecting and testing, complete all as specified and directed. |
| 14 | Dismantling the monoblock pumpset any capacity after disconnecting suction and delivery pipes including electrical connection, transporting the pumpset any make of capacity 3.0 HP to workshop for carringout repairs/servicing and overhauling including greasing / oiling, replacement of workout bushes, bolts and nuts etc including replacement of defective spares complete and including painting of pumpset after preparation of oil surface by scrapping, cleaning and apply two coats of synthetic enamelled paint with spray gun and writing the SM/MES No including suction and delivery pipe lines along with writing of the details of feeder lines with indication and detecting any repair in the pumpset after connecting, testing complete all as specified and as directed. Note: Spares will be measured and paid separately under relevant items. |
| 15 | Supply only the following spares sutable for monoblock pumpset of capacity 3.0 HP. (a) Ball bearings (drive/ non drive) |
| 16 | (b) Cooling fan blade PVC. |
| 17 | (c) Terminal Box. |
| 18 | (d) Terminal connectors 3 phase. |
| 19 | (e) Electro dynamically balanced bronze impeller |
| 20 | (f) Shaft (Mild steel) |
| 21 | (g) Gun metal bush |
| 22 | (h) Gland cup with bolts and nuts. |
| 23 | (i) Water seal. |
| 24 | (j) Flange drilled suitable size with bolts, nuts and rubber gasket. |
| 25 | (k) Air cock nozzle brass |
| 26 | (l) Shaft coupling. |
| 27 | M&L for rewinding of electric motor of any make of capacity 3.0 HP, by dismantling and removing the old burnt windings and rewinding for suitable gauge of enamelled copper wire and insulating with suitable class of insulation, varnishing complete including repairs to terminal box of motor, connecting and testing, complete all as specified and directed. |
| 28 | Dismantling the monoblock pumpset any capacity after disconnecting suction and delivery pipes including electrical connection, transporting the pumpset any of capacity 5.0 HP to 7.0 HP to workshop for carringout repairs/servicing and overhauling including greasing / oiling, replacement of workout bushes, bolts and nuts etc including replacement of defective spares complete and including painting of pumpset after preparation of oil surface by scrapping, cleaning and apply two coats of synthetic enamelled paint with spray gun and writing the SM/MES No including suction and delivery pipe lines along with writing of the details of feeder lines with indication and detecting any repair in the pumpset after connecting, testing complete all as specified and as directed. Note: Spares will be measured and paid separately under relevant items. |
| 29 | Supply only the following spares sutable for monoblock pumpset of capacity 5.0 HP. (a) Ball bearings (drive/ non drive). |
| 30 | (b) Cooling fan blade PVC. |
| 31 | (c) Terminal Box. |
| 32 | (d) Terminal connector 3 Phase. |
| 33 | (e) Electro dynamically balanced bronze impeller |
| 34 | (f) Shaft (Mild steel) |
| 35 | (g) Gun metal bush |
| 36 | (h) Gland cup with bolts and nuts. |
| 37 | (i) Water seal. |
| 38 | (j) Flange drilled suitable size with bolts, nuts and rubber gasket. |
| 39 | (k) Air cock nozzle brass |
| 40 | (l) Shaft coupling. |
| 41 | M&L for rewinding of electric motor of any make of capacity 5.0 HP, by dismantling and removing the old burnt windings and rewinding for suitable gauge of enamelled copper wire and insulating with suitable class of insulation, varnishing complete including repairs to terminal box of motor, connecting and testing, complete all as specified and directed. |
| 42 | Dismantling the monoblock pumpset any capacity after disconnecting suction and delivery pipes including electrical connection, transporting the pumpset any of capacity 7.5 HP to 9.5 HP to workshop for carringout repairs/servicing and overhauling including greasing / oiling, replacement of workout bushes, bolts and nuts etc including replacement of defective spares complete and including painting of pumpset after preparation of oil surface by scrapping, cleaning and apply two coats of synthetic enamelled paint with spray gun and writing the SM/MES No including suction and delivery pipe lines along with writing of the details of feeder lines with indication and detecting any repair in the pumpset after connecting, testing complete all as specified and as directed.Note: Spares will be measured and paid separately under relevant items. |
| 43 | Supply only the following spares sutable for monoblock pumpset of capacity 7.5 HP. (a) Ball bearings (drive/ non drive). |
| 44 | (b) Cooling fan blade PVC. |
| 45 | (c) Terminal Box. |
| 46 | (d) Terminal connector 3 Phase. |
| 47 | (e) Electro dynamically balanced bronze impeller |
| 48 | (f) Shaft (Mild steel) |
| 49 | (g) Gun metal bush |
| 50 | (h) Gland cup with bolts and nuts. |
| 51 | (i) Water seal. |
| 52 | (j) Flange drilled suitable size with bolts, nuts and rubber gasket. |
| 53 | (k) Air cock nozzle brass |
| 54 | (l) Shaft coupling. |
| 55 | M&L for rewinding of electric motor of any make of capacity 7.5 HP, by dismantling and removing the old burnt windings and rewinding for suitable gauge of enamelled copper wire and insulating with suitable class of insulation, varnishing complete including repairs to terminal box of motor, connecting and testing, complete all as specified and directed. |
| 56 | Dismantling the monoblock pumpset any capacity after disconnecting suction and delivery pipes including electrical connection, transporting the pumpset any of capacity 10.0 HP to workshop for carringout repairs/servicing and overhauling including greasing / oiling, replacement of workout bushes, bolts and nuts etc including replacement of defective spares complete and including painting of pumpset after preparation of oil surface by scrapping, cleaning and apply two coats of synthetic enamelled paint with spray gun and writing the SM/MES No including suction and delivery pipe lines along with writing of the details of feeder lines with indication and detecting any repair in the pumpset after connecting, testing complete all as specified and as directed. Note: Spares will be measured and paid separately under relevant items. |
| 57 | Supply only the following spares sutable for monoblock pumpset of capacity 10.0 HP. (a) Ball bearing suitable for motor |
| 58 | (b) Ball bearings suitable for pump |
| 59 | (c) Cooling fan blade PVC. |
| 60 | (d) Terminal Box. |
| 61 | (e) Terminal connectors 3 phase. |
| 62 | (f) Electro dynamically balanced bronze impellor |
| 63 | (g) Shaft (Mild steel) |
| 64 | (h) Gland sleeve |
| 65 | (i) Water seal. |
| 66 | (j) Air cock nozzle brass |
| 67 | (k) Shaft coupling. |
| 68 | M&L for rewinding of electric motor of any make of capacity 10.0 HP, by dismantling and removing the old burnt windings and rewinding for suitable gauge of enamelled copper wire and insulating with suitable class of insulation, varnishing complete including repairs to terminal box of motor, connecting and testing, complete all as specified and directed. |
| 69 | Supply only the following spares sutable for monoblock pumpset of capacity 12.5 to 15.0 HP. (a) Ball bearing suitable for motor |
| 70 | (b) Ball bearings suitable for pump |
| 71 | (c) Cooling fan blade PVC. |
| 72 | (d) Terminal Box. |
| 73 | (e) Terminal connectors 3 phase. |
| 74 | (f) Electro dynamically balanced bronze impellor |
| 75 | (g) Shaft (Mild steel) |
| 76 | (h) Gland sleeve |
| 77 | (i) Water seal. |
| 78 | (j) Air cock nozzle brass |
| 79 | (k) Shaft coupling. |
| 80 | M&L for rewinding of electric motor of any make of capacity 12.5 to 15.0 HP, by dismantling and removing the old burnt windings and rewinding for suitable gauge of enamelled copper wire and insulating with suitable class of insulation, varnishing complete including repairs to terminal box of motor, connecting and testing, complete all as specified and directed. |
| 81 | Supply only the following spares sutable for monoblock pumpset of capacity 20.0/25 HP. (a) Ball bearing suitable for motor |
| 82 | (b) Ball bearings suitable for pump |
| 83 | (c) Cooling fan blade PVC. |
| 84 | (d) Terminal Box. |
| 85 | (e) Terminal connectors 3 phase. |
| 86 | (f) Electro dynamically balanced bronze impellor |
| 87 | (g) Shaft (Mild steel) |
| 88 | (h) Gland sleeve |
| 89 | (i) Water seal. |
| 90 | (j) Air cock nozzle brass |
| 91 | (k) Shaft coupling. |
| 92 | M&L for rewinding of electric motor of any make of capacity 20.0/25 HP, by dismantling and removing the old burnt windings and rewinding for suitable gauge of enamelled copper wire and insulating with suitable class of insulation, varnishing complete including repairs to terminal box of motor, connecting and testing, complete all as specified and directed. |
| 93 | Supply only the following spares sutable for monoblock pumpset of capacity 30.0 HP. (a) Ball bearing suitable for motor |
| 94 | (b) Ball bearings suitable for pump |
| 95 | (c) Cooling fan blade PVC. |
| 96 | (d) Terminal Box. |
| 97 | (e) Terminal connectors 3 phase. |
| 98 | (f) Electro dynamically balanced bronze impellor |
| 99 | (g) Shaft (Mild steel) |
| 100 | (h) Gland sleeve |
| 101 | (i) Water seal. |
| 102 | (j) Air cock nozzle brass |
| 103 | (k) Shaft coupling. |
| 104 | M&L for rewinding of electric motor of any make of capacity 30.0 HP, by dismantling and removing the old burnt windings and rewinding for suitable gauge of enamelled copper wire and insulating with suitable class of insulation, varnishing complete including repairs to terminal box of motor, connecting and testing, complete all as specified and directed. |
| 105 | Taking out unserviceable non return valve 80 mm bore iron pipe including fittings/ fixtures complete all as specified and directed. |
| 106 | All as per item No. 22.00 above but for 50mm bore pipes. |
| 107 | S&F foot valve with cast iron body and brass spindle suitable for 80mm bore CI/ GI pipe complete with flanged and leather diaphragm, brass spindle, including replacement of bolts, nuts, gaskets etc. including taking down existing un-serviceable foot valve complete all as specified and directed. |
| 108 | All as per item No. 24.00 above but for 50mm bore pipes. |
| 109 | Taking out unserviceable non return valve 100 mm bore iron pipe including fittings/ fixtures complete all as specified and directed. |
| 110 | All as per item No. 26.00 above but for 80mm bore pipes. |
| 111 | All as per item No. 26.00 above but for 50mm bore pipes. |
| 112 | Supply and fix non return valve with gun metal body suitable for 100mm bore CI/ GI pipe with flanged ends including making alterations to existing pipes as required and testing including taking down existing valve complete all as specified and directed. |
| 113 | All as per item No. 29.00 above but for 80mm bore pipes. |
| 114 | All as per item No. 29.00 above but for 50mm bore pipes. |
| 115 | Dismantling horizontal/ vertical submersible motor upto 05 HP 3 Phase, 415 V, removing the burnt winding wires, cleaning the slots and rewind the stator with super enamelled copper winding wire of the same gauge, reassembling the motor complete after replacing the following items:-(a) Motor gun metal bush - 02 No.(b) Thrust bearing - 01 No.(c) Stud bolts - 04 No. |
| 116 | Dismantling horizontal/ vertical submersible motor upto 10 HP 3 Phase, 415 V, removing the burnt winding wires, cleaning the slots and rewind the stator with super enamelled copper winding wire of the same gauge, reassembling the motor complete after replacing the following items:-(a) Motor gun metal bush - 02 No.(b) Thrust bearing - 01 No.(c) Stud bolts - 04 No. |
| 117 | Dismantling horizontal/ vertical submersible motor 03 HP 3 Phase, 415 V, removing the burnt winding wires, cleaning the slots and rewind the stator with super enamelled copper winding wire of the same gauge, reassembling the motor complete after replacing the following items:-(a) Motor gun metal bush - 02 No.(b) Thrust bearing - 01 No.(c) Stud bolts - 04 No. |
| 118 | Supply and fix gland rope of any size after removing out old unserviceable one complete all as specified and directed. |
| 119 | Supply and fix rubber coupling suitable for upto 20 HP motor including taking out old unserviceable one complete all as specified and directed. |
| 120 | Supply, install, testing and commissioning of pressure vessel with bladder suitable for capacitor start mono block pressure pump upto 0.50 HP capacity including taking down the existing unserviceable one complete all as specified and directed. |
| 121 | Supply, install, testing and commissioning electronic controlling device suitable for capacitor start mono block pressure pump upto 1 HP capacity including taking down the existing unserviceable one complete all as specified and directed. |
| 122 | Taking out unserviceable GI pipe 100 mm bore from trenches including fittings/ fixtures like bend, Tee, Union, elbow etc. complete all as specified and directed. |
| 123 | All as per item No. 39.00 above but 80 mm bore GI pipe. |
| 124 | All as per item No. 39.00 above but 50 mm bore GI pipe. |
| 125 | All as per item No. 39.00 above but 40 mm bore GI pipe. |
| 126 | All as per item No. 39.00 above but 25 mm bore GI pipe. |
| 127 | Supply and lay in trenches 100mm bore GI tubing medium grade with screw, socket joints with all fittings/ fixtures like bends, sockets, unions, nipples etc. including making alterations in existing/ new pipe as required complete all as specified and directed. |
| 128 | All as per item No. 44.00 above but 80mm dia GI tubing. |
| 129 | All as per item No. 44.00 above but 50mm dia GI tubing. |
| 130 | All as per item No. 44.00 above but 40mm dia GI tubing. |
| 131 | All as per item No. 44.00 above but 25mm dia GI tubing. |
| 132 | Supply and fix electronic automatic phase sequence corrector suitable for various capacity star-delta starter including taking down the existing unserviceable one complete all as specified and directed. |
| 133 | Taking down the existing unserviceable over load protector relay and replace with new overload relay, range 6 - 39 Amps complete all as specified and directed. |
| 134 | Supply and fix single phasing preventer to various HP suitable for star delta starter including taking down the existing unserviceable kit complete all as specified and directed. |
| 135 | Taking down the existing unserviceable contactor and replace with new contactor suitable for MK-1 starter complete all as specified and directed. |
| 136 | Taking down the existing unserviceable timer and replace with new Timer suitable for ML-1 star delta starter complete all as specified and directed. |
| 137 | Taking down the existing unserviceable No. volt coil and replace with new No volt coil suitable for ML-1 star delta starter complete all as specified and directed. |
| 138 | Supply and fix DOL starter 3 phase 440 volts with relay range upto 16 amps including taking down the existing unserviceable one complete all as specified and directed. |
| 139 | Supply and fix star delta starter with single phase protection and relay range from 13-32 amps 3 phase 440 volts including taking down the existing unserviceable starter complete all as specified and directed. |
| 140 | Supply and fix MCB, 4 pole, 415 volts, 3 phase, 50 c/s, 63 Amps capacity including taking down the existing unserviceable one complete all as specified and directed. |
| 141 | Supply and fix MCB SP 20 Amps 240 V, AC including taking down the existing unserviceable one complete all as specified and directed. |
| 142 | Supply and fix MCB SPN 40 Amps AC 240 volts including taking down the existing unserviceable one complete all as specified and directed. Please Enable Macros to View BoQ information |
| 143 | Supply and fix MCB SPN 40 Amps AC 240 volts including taking down the existing unserviceable one complete all as specified and directed. Please Enable Macros to View BoQ information |
AI Tender Summary
Tender Timeline
Jul 07, 2026
11:30 IST
Tender Published
Tender notice published.
CompletedJul 28, 2026
17:00 IST
Bid Submission Deadline
Online submission via eProcurement portal.
Upcoming · 18 daysJul 30, 2026
Bid Opening Date
Technical bids will be opened and evaluated.
Upcoming · 20 daysTender Documents
Download All (ZIP) ↓
Disclaimer
We takes all possible care for accurate & authentic tender information. However users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender