Tender For Temporary Aluminium Partition And Repair Works In Acd Court Jhunjhunu
Tender Value
6.64 Lakhs
Estimated cost
Bid Submission
16 Jul 2026
7 days left
EMD
13280
Bank guarantee accepted
Document Fee
500
Non-refundable
Tender Type
Online
Tender Overview
Organization
Tender ID
Competition Type
NCB
Bidding Type
Tender
Location / State
Jhunjhunu → Rajasthan
EMD Exemption
Available
Quantity
Not Available
Website
Contact Person
Address
Project Description
Tender For Temporary Aluminium Partition And Repair Works In Acd Court Jhunjhunu
BOQ
| Sl. No. | Item Description |
| 1 | Civil Work : |
| 2 | Brick work with F.P.S. bricks of class designation 75 insuperstructure above plinth level upto floor V level in allshapes and sizes in :Cement mortar 1 : 6 (1 cement : 6 coarse sand) |
| 3 | Plaster on new surface on walls in cement sand mortar 1:4 including raking of joints etc. complete fine finish : 20 mm thick |
| 4 | Random rubble dry stone Kharanja under floor. |
| 5 | Finishing walls with Acrylic Smooth exterior paint of requiredshade including all scaffolding. New work (Two or more coat applied @ 1.67 ltr/10 sqm over and including base coat of water proofing cement paint applied @ 2.20 kg/ 10 sqm ). |
| 6 | Providing and fixing M.S. sheet 1mm thick single leaf door shutter in angle iron frame 35x35x5mm suitabilly diagonally braced with 25x3mm flat iron above and below lock rail of size 50x5mm beading extra including all fittings, as per direction of Engg. incharge but excluding cost of chowkhats: including two coats of anit-corrosive red oxide primer paint |
| 7 | Providing and fixing pressed steel door frames confirming to IS 4351 manufactured from commercial mild steel sheet of 1.25 mm thickness including hinges jamb, lock jamb, bead and if required angle threshold of mild steel angle of section 50x25mm, or base ties of 1.25mm pressed mild steel welded or rigidly fixed together by mechanical means, adjustable lugs with split end tail to each jamb including steel butt hinges 2.5mm thick with mortar guards, lock strike-plate and shock absorbers as specified and applying a coat of approved steel primer after pre-treatment of the surface including filling with CC 1:2:4(M15 grade) complete as directed by Engineer-in-charge : Profile C |
| 8 | Providing and fixing steel gate, grating , and grills made of angles, tees, square bars, flats,or black pipe with holdfast and fittings complete as per design and drawing including cutting welding and fabrication with priming coat of red oxide |
| 9 | Demolishing cement concrete manually/ by mechanical means including disposal of material within 50 metres lead as per direction of Engineer-in-charge. |
| 10 | 1: 3: 6 or richer mix |
| 11 | Providing and laying in position cement concrete including curing, compaction etc. complete in specified grade excluding the cost of centering and shuttering - All work up to plinth level. M10 grade Nominal Mix 1: 3: 6 (1 cement : 3 coarse sand : 6 graded stone aggregate 20mm nominal size). |
| 12 | Kota stone slab flooring 25 mm thick over 20 mm (average)thick base laid over and jointed with grey cement slurrymixed with pigment to match the shade of the slab includingrubbing and polishing complete with base of cement mortar 1: 4 (1 cement : 4 coarse sand) |
| 13 | For area of each slab from 901 to 2000 Sq.Cm : |
| 14 | Dismantling tile work in floors and roofs laid in cement mortar including stacking of serviceable material and disposal ofunserviceable material within 50 meter lead |
| 15 | For thickness of tiles 10mm to 25mm |
| 16 | Providing and fixing 1st quality standard white, grey, ivory,fume red brown, light green, light blue and other light shadesglazed tiles confirming to code IS : 15622 of size 200mm x300mm in walls, floors, steps, pillars etc. laid on a bed of neat cement slurry finished with flush pointing in the white cement mixed with pigment to match the shade of the tile complete (excluding the cost of cement plaster on walls and pillar). |
| 17 | Extra for using size above 200x300mm in glazed tiles andfor using 400mm x 400mm MAT finished tiles in place of300mm x 300mm size |
| 18 | P & F 1st quality Heavy Duty Vitrified glazed MAT tiles onfloor, skirting and steps etc.in different sizes (thicknessminimum 10mm) with water absortion less than or equal0.08% and conforming to IS 15622 of approved make in allcolour and shade, laid with 20 mm thick CM 1: 4 includinggrounting the joints with white cement and matching pigmentetc complete. |
| 19 | Structural steel work riveted, bolted or welded in built up sections, trusses and framed work, including cutting, hoisting (height upto 10 m) , fixing in position and applying a priming coat of approved steel primer all complete: |
| 20 | Supply and installation of Multi Rib Proofing/cladding Sheet Manufacture out of 0.50mm TCT (Total Coated Thickness) high tensile Zinc aluminum alloy coated galvalume steel (as per 150gsm zinc aluminum coated 550Mpa tuekd strength) confirming to IS: 1397/astm A-792 sheet to have wide pens 30mm high NB at 250 centre and centre width of 1020mm heets be casted with regular modified polyster system on a continuous with line on centre for face and with a polyster coating respectively sheet shall have proportionality with siphoned plate made to prevent leakage sheet shall be fixed by more of sell drilling lift tapping hot dip zinc coated hox head fasterner of size 12x14x55mm long. The sheet shall be supplied in cost one length and for a minimum up to 12mts with all scaffolding. |
| 21 | Providing and fixing aluminum work for doors ,windows,ventilators and partition with extruded built up standardtubular / appropriate Z sections and other sections of approved make conforming to IS :733 and IS :1285, fixed with rawl plugs and screws or with fixing clips ,or with expansion hold fasteners including necessary filling up of gap. at junctions ,at top ,bottom and sides with required PVC/neoprene felt etc. Aluminium section shall be smooth ,rust free, straight ,mitered and jointed mechanically wherever required including cleat angle Aluminium snap beading for glazing /paneling , C.P. brass/ stainless steel screws Al. Tower bolt & Al. handle & Al. Aldrop etc.,all complete as per architectural drawings and the directions of Engineer- in – charge .(Glazing and paneling to be paid for separately).For fixed portion Anodised aluminum (anodised transparent 81 dyed to required shade according to IS : 1868. (Minimum anodic coating of grade AC 15, Anodizing to be got done from approved Anodizer) |
| 22 | Providing & Fixing Aluminium composite panel of indobond/euro/flexi bond of equivalent made 3mm that with0.5mm thick skin& PVDF coated of approved shads for toiletdoor in double layer in Aluminium frame complete in allrespect as per sample approved by Engineer in Charges |
| 23 | Providing and fixing steel gate, grating , and grills made of angles, tees, square bars, flats,or black pipe with holdfast and fittings complete as per design and drawing including cutting welding and fabrication with priming coat of red oxide |
| 24 | Painting with enamel paint of approved brand and manufacture to give an even shade: One or more coats on old work. |
| 25 | Providing & Fixing Commercial Ply as per IS 710 : 1976 BWR of approved make for making wardrobe/shelves and other furniture with fevicol & nails complete as per approved by engineer in charge 18 mm thick |
| 26 | Providing & Fixing mica of approved make for inner/outer side of shutters with fevicol & nails complete as per approved by engineer in charge 0.6mm thick mica |
| 27 | Providing and fixing IS : 3564 marked aluminium extruded section body tubular type universal hydraulic door closer with double speed adjustment with necessary accessories and screws etc. complete. |
| 28 | Providing and fixing calcium silicate board false ceiling at allheights including providing and fixing of frame work made ofspecial sections power pressed from M.S. sheet and galvanised in accordance with zinc coating of grade 350 asper IS : 277 and consisting of angle cleats of size 25mm widex 1.6mm thick with flanges of 22mm and 37mm at 1200mmcentre to centre one flange fixed to the ceiling with dashfastener 12.5mm diax40mm long with 6mm dia bolts to theangle hangers of 25x25x0.55mm of required length, andother end of angle hanger being fixed with nut and bolts toG.I. channels 45x15x0.9mm running at the rate of 1200mmcentre to centre to which the ceiling section 0.5mm thickbottom wedge of 80mm with tapered flanges of 26mm eachhaving clips of 10.5mm at 450mm centre to centre shall befixed in a direction perpendicular to G.I. channel withconnecting clips made out of 2.64mm diax230mm long G.I. wire at every junction including fixing the calciumsilicate board with ceiling section and perimeter channels0.5mm thick 27mm high having flanges of 20mm and 30mmlong, the perimeter of ceiling fixed to wall/partition with thehelp of rawl plugs at 450mm centre to centre with 25mm longdrive-all screws @ 230mm interval including jointing andfixing to a flush finish of tapered and square edges of theboard with recommended filler, jointing tapes, finisher andtwo coats of primer suitable for board as per manufacturesspecification and also including the cost of making openingsfor light fittings, grills, diffusers, cutouts made with frame ofperimeter channels suitably fixed all complete as per drawingand specification and direction of the Engineer in Charge butexcluding the cost of painting of thickness of calcium silicateboard as below:- |
| 29 | 8 mm thick |
| 30 | Providing and Fixing Cushion Vinyl/Fully flexible Vinyl Flooring confirming to I.S.-3462 Flooring of approved make with fibre base using rubber base adhesives including rollingwith light wooden roller complete : |
| 31 | 2.0 mm thick |
| 32 | Providing & fixing door, window, chowkhats and other frames, including antitermite treatment, M.S. flat, hold fasts of size 250 x 40 x 3mm fixed with M.S. bolt 5mm dia 50mm long duly embedded in cement concrete M-15 grade : Sal wood Grade - I. |
| 33 | French sprit polishing |
| 34 | Two or more coats on new work including a coat of woodfiller. |
| 35 | P & F Kitchen & Lab. Sink of approved make with C.I.brackets duly painted, 40 mm C.P. waste coupling, C.P. Brass chain with rubber plug, 40 mm G.I. waste pipe up-to floor level complete including cutting and making good the wall & floor : |
| 36 | 1.0 mm thick stainless steel AISI -304 & IS 13983-1994kitchen sink of approved make as per Engineer-in-charge withlarge waste coupling. Overall size 22 x 18 x 7 Bowl size 20x16x7 |
| 37 | P & F Sink Cocks of superior quality & approved made : |
| 38 | C.P. Sink cock swinging spout 15mm |
| 39 | P & F Inlet Connection (Angle Valves) Superior quality, ofapproved make, for Wash basin, Gyser etc. |
| 40 | C.P. Inlet connection 15mm.Brass (IS : 8931 marked) |
| 41 | P & F 15 mm. Dia Connection Pipe of approved quality/make |
| 42 | PVC pipe with C.P. Brass nuts upto length 600mm |
| 43 | P & F G.I. pipes (Internal Work) with G.I. Fittings excludingunion (IS:1239 Mark) & MS clamps including cutting andmaking good the walls and floors Exposed on wall |
| 44 | 15 mm dia nominal bore 'A' Class |
| 45 | P&F rigid PVC Pipe (IS:4985 mark) class II/ (4 Kg. /Cm2 .) approved quality /make including joining the pipe with solvent cement rubber ring and lubricant. |
| 46 | 110 mm dia |
| 47 | Providing and Fixing Unplasticized Poly Vinyl Chloride(UPVC) SWR Pipes fittings type B for sciland waste discharge system (IS:13592 : 1992 Marked) of approved quality /make |
| 48 | 110mm dia |
| 49 | P & F Grating of approved quality/make: |
| 50 | Stainless Steel Sheet size 125mm dia. Heavy Quality of approved make |
| 51 | P&F rigid PVC pipe fittings (IS: 4985 mark) of approvedquality /make including joining the pipe with solvent cement rubber ring and lubricant |
| 52 | Door Bend (Left & Right) 110mm dia |
| 53 | Labour charges for removing W.C. pan (any type) of all sizes with care including all necessary fittings P or S trap. |
| 54 | Providing & Fixing Premium Quality white glazed vitreouschina Sanitary Wares (IS:2556 Mark) of approved make as per direction of Engineer-in-charge including cutting and making good the wall and floor. |
| 55 | Double Syphonic European W.C. with mounted W.V.C.flushing cistern of 10 litre capacity complete with allnecessary internal fittings with Hydraulic seat cover. |
| 56 | P&F Looking Mirror 5mm thick of approved make withornamental frame size 50x12 with 6mm Ply Board on BackSide Complete as per approved sample |
| 57 | Providing & Fixing brass handle 125mm with plate175x22mm with screw complete in all respect as per direction of Engineer in charges |
| 58 | P & F Toilet Shelf of approved quality/make |
| 59 | Glass Shelf with edges rounded off Anodised Aluminiumangle frame & C.P. brass brackets & guard rail size600x120mm |
| 60 | Providing & Fixing premium quality Toilet corner Glass Shelf size 225x225mm with C.P. brass brackets & guard rail edges rounded of SS frame |
| 61 | P & F Toilet Paper Holder with rod of approvedquality/make: C.P. brass heavy & Superior quality |
| 62 | Providing and fixing Superior quality CP Brass fittings ofapproved make as per direction of Engineer-in-charge |
| 63 | Two way Bib Cock 15 mm nominal size |
| 64 | Providing and fixing Superior quality CP Brass fittings ofapproved make as per direction of Engineer-in-charge |
| 65 | Health focet (Premium heavy Quality) as approved byEngineer-in-Charge |
| 66 | P & F Towel Rail or Ring of approved quality/make C.P. Brass Towel Ring revolving type |
| 67 | Providing and fixing Superior quality CP Brass fittings ofapproved make as per direction of Engineer-in-charge |
| 68 | 600 mm long towel rail |
| 69 | C.P. brass heavy and superior quality |
| 70 | P & F Liquid Soap Container with brackets complete ofapproved make C.P. Brass |
| 71 | Supplying and fixing Rollor Blinds of good quality and approved make made out of Imported fabric including Roller Mechanism and lock with chain system with all necessary hooks etc. complete as per direction and sample approved by engineer-in-charge. Please Enable Macros to View BoQ information |
AI Tender Summary
Tender Timeline
Jul 06, 2026
11:30 IST
Tender Published
Tender notice published.
CompletedJul 16, 2026
17:00 IST
Bid Submission Deadline
Online submission via eProcurement portal.
Upcoming · 7 daysJul 17, 2026
Bid Opening Date
Technical bids will be opened and evaluated.
Upcoming · 8 daysTender Documents
Download All (ZIP) ↓
Disclaimer
We takes all possible care for accurate & authentic tender information. However users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender