Tender For Providing Of New Cadf Hut At Afs Jaisalmer
Tender Value
36.45 Lakhs
Estimated cost
Bid Submission
20 Jul 2026
10 days left
EMD
72912
Bank guarantee accepted
Document Fee
500
Non-refundable
Tender Type
Online
Tender Overview
Organization
Tender ID
Competition Type
NCB
Bidding Type
Tender
Location / State
Jaisalmer → Rajasthan
EMD Exemption
Available
Quantity
Not Available
Website
Contact Person
Address
Project Description
Tender For Providing Of New Cadf Hut At Afs Jaisalmer
BOQ
| Sl. No. | Item Description |
| 1 | Surface excavation n. exc 30cm deep and averaging 15 cm deep and getting out in ordinary/Loose soil. |
| 2 | Removing of surplus excavated soil obtaine d from item No 1 above to a distance exc 250m but not exc 500m and depositing where directed at a level n exc 1.5m above the starting point. |
| 3 | Design manufacture supply and errection of pre-fabricated shelter with and including foundation and plinth work in RCC M-25 grade concrete, Steel superstructure,roof covering with PPGI sheet 0.5 mm thick roof covered, false ceiling powder coated GI members with decorative fissure board ceiling tiles, double skin with Puff insulated PPGI wall panel 50mm thick,powder coated alu window/partitions with doors partly glazed and partly panelled with internal electrification, water supply and construction of raised plinth 45 cm height with rammed earth moorum filling, PCC (1:4:8) type D-2 in subbase, Vitrified ceramic tiles in Floors an 1.50m wide Plinth protection etc complete all as shown in drawing and as specified. |
| 4 | M&L for hardcore with broken stones or boulders of gauge n exc 63mm, deposited,spread and levelled in layers n exc 15cm thick, watered and well rammed/rolled to a true surface |
| 5 | M&L for 100mm thick PCC (1:4:8) type D-2 (40mm graded stone aggregate) as in subbase finished to receive floor treatment |
| 6 | M&L for 100mm thick PCC (1:2:4) type B-1 (20mm graded stone aggregate) as in floors finshed even and smooth without using extra cement with mechanical floater machines |
| 7 | M&L for cutting of existing concrete floors using diamond cutters for formimg construction joints 10mm wide and 30mm deep and filled with bituminous sealing compound grade 'B\\" etc complete all as specified. |
| 8 | M&L for cutting of existing concrete floors using diamond cutters for formimg Contraction (Dummy) joints 10mm wide and 65mm deep and filled with bituminous sealing compound grade 'B\\" etc complete all as specified. |
| 9 | Surface dressing n exc 15 cm deep and getting out in ordinary/loose soil. |
| 10 | M&L for 50mm thick PCC (1:2:4) type B-1 (20mm graded stone aggregate) as in vegetation proof hard standing ground finshed even and smooth without using extra cement |
| 11 | S&F steel work in tubular trusses including special shaped washer etc. Complete using ERW or induction butt welded tubes conferming to IS 1161-1979 grade St -240. |
| 12 | Preparation of newly steel surface and applying two coat of synthetic enamel paint over a coat of red oxide all as specfied |
| 13 | Excavating in post holes (or similar holes) each n exc 0.5 cum getting out, returning , filling in and ramming earth or broken rubble mixed with earth around, in layers not exceeding 25 cm, watering and removing surplus soil to a distance n exc 50 m and making good surface. |
| 14 | 1. M&L for concealed point wiring for controlled by one switch with PVC insulated but unsheathed single core FRLSH multistranded copper conductor cable IS-694 marked of size 1.5 Sqmm (nominal area) in and including PVC casing capping 20 mm width in walls and making good the surface in CM 1:3 and to the original specification and PVC casing capping on ceiling for steel structure/surface etc for FRP ceiling with including one run of PVC insulated FRLSH copper conductor cable of 1.5 Sqmm with green insulation as earth wire and connected to earth dolly complete all as specified and directed.(a) One light point controlled by one, one way switch |
| 15 | -Ditto- all item as per Ser No 16 above but One socket outlet 3 Pin, 6 Amp on independent board |
| 16 | -Ditto- all item as per Ser No 16 above but One socket outlet 3 Pin, 6 Amp on same board. |
| 17 | M&L for point wiring for controlled by one switch with PVC unsheathed single core multistranded copper conductor cable of size 4 Sqmm (nominal area) in and including PVC cassing capping 20 mm width in walls by cutter and making good the surface in CM 1:3 and to the original specification and PVC cassing capping on ceiling for steel structure/surface conduit with clamps, gutties etc for RCC ceiling including one run of PVC insulated FRLSH copper conductor cable of 4 Sqmm with green insulation as earth dolly for 6 pin, 16 Amp socket outlet on Independent board. |
| 18 | S&F switch piano flush type single pole one way 5 Amp (ISI Marked) |
| 19 | S&F switch piano flush type single pole one way 15 Amp (ISI Marked) |
| 20 | S&F socket out let 2 in 1, 3 pin 5 Amp flush type (ISI Marked) |
| 21 | S&F socket out let 2 in 1, 3 pin 15 Amp flush type (ISI Marked ) |
| 22 | M&L for ceiling rose, surface Bakelite 65 x 17.50 mm of three terminals PVC/Polycarbonate,isolated body (ISI Marked) |
| 23 | Supply and fixing Surface and wall mounted LED tube light fittings of cap 20W , four feet Basic all purpose surface and wall mounted LED batten with polycarbonate housing including providing of two Nos PVC square box for mounting of tube light all as specified and directed. |
| 24 | Supply & fix Prewired Distribution Board factory made sheet metal enclosure double door distribution board class IP-43 with 200 Amp rated copper bus bar 240 Volts 4 way VTPN complete all as directed by Engineer-in-Charge. |
| 25 | S & F MCB, 6 to 32 Amp, SP, 240 Volt. complete all as specified and directed. |
| 26 | S&F MCB, 32 Amp, SPN, 240 Volt complete all as specified and directed. |
| 27 | S&F MCB, 63 Amp, TPN, 240 Volt complete all as specified and directed. |
| 28 | S&F MCCB 125 Amp, TP 415 volts 16 KA, 'C' curve complete all as specified and directed. |
| 29 | M&L for submain wiring with 2 single core PVC insulated unsheathed multi stranded copper conductor FRLSH wire 6.00 Sq mm 1100 volts grade including and 06.00 Sq mm PVC insulated, multi stranded, unsheathed copper wire green in colour as earthing lead drawn through in PVC casing capping / conduit incl cutting, chases in stone wall as required and match with the existing surface complete all as specified and directed.Note : Two run of 06.0 Sqmm cable and one run of 6.0 Sqmm cable as earth continuity conductor shall be measured & paid as one unit. |
| 30 | MCB Protected Socket (Modular AC Box, Metal clad box) Two Module, Single Pole, 20 Amps, repturing capacity 10 kA and neutral enclosure in sheet steel with a two pin and earth plug and socket complete all as specified and directed. |
| 31 | Supply, installation, commissioning and testing of cubical, outdoor type CPRI approved LT bus bar Box totally enclosed weather and vermi proof , fully compartmentalised made out of 3.15 mm thick CRCA sheet for load bearing and 2mm thick for non load bearing Portion, protection of enclosure IP-66 complete with tow coat synthetic enamel paint over one coat of Red oxide primer , locking arrangement , front size and rear side opening arrangement of suitable size , mounted on angle iron stand of angle size 50x50x6mm having min height 45cm from floor level, excavation and earth work , PCC foundation (mini 45cm height from GL), making all incoming and out going connection with suitable size copper :- (a) 4 Nos bus bar of equal size made by copper conductor with PVC insulated colored heat shrinkable type sleeves, rating bus bar 315 Amps , mounted on non cracking resin type insulator – 1 Set with suitable capacity of CT,s, Ammeter , Volt meter frequency meter , selector switch and indication lamp, LED indication lamps for ON, OFF & RYB, etc (b) MCCB, 3 Phase and neutral, 415 V thermal magnetic type , 4 Poles , rating 200 Amps , with rupturing capacity 36 KA – 1 No (incoming). |
| 32 | M&L for Earthing complete with galvanized steel earth plate electrode 60 cm x 60 cm x 6 mm thick surrounded with charcoal and salt, buried directly in ground (earth pit not less than 2.25 metre deep below ground level) with top edge of plate not less than 1.5 metre below normal ground level connected to galvanized earth lead wire 4 mm dia by means of bolts, nuts, check nuts and washers of galvanized iron or steel all as shown in electrical Plate No 3 of MES SSR Part-I connected to main switch board or main control board all as specified and testing on completion including provision of earth wire protected by galvanized iron 15 mm dia light grade pipe and watering pipe shall be 20 mm bore light grade including all excavation and earth work in any type of soil, PCC pit with pre-cast RCC cover, charcoal/salt, funnel etc complete all as directed.(i) The concrete pit shall be PCC 1:3:6 type C-1, 40 mm thick pre cast cover slab of RCC (1:2:4) type B-1 using 20mm graded stone aggregate reinforced with 8mm TMT bars @ 10 cm C/C on both sides with suitable cast iron handle shall be provided in lieu of cast iron cover shown in electrical plate No 3 of MES SSR Part-I.(ii) Item includes the cost of 7.50m GI pipe for protection of earth wire/strip Any variation in length shall be adjusted through deviation order. (iii) Item includes cost of 7.50m earth lead wire/strip. Any variation in length shall be adjusted through deviation order.(iv) PCC pit shall be provided at least 500 mm away from the pit and not on the earth pit itself and the extra cost of additional length of watering pipe, bends, elbow etc shall be deemed included in the unit rate. |
| 33 | M&L for maintenance free chemical earthing of technology 3 mtr long 17.20 mm dia with 250-micron Copper coating and UL listed. There should be terminal for connection of 150 x 50 x 6 mm with 4 hole of 12 mm dia along with 2 bags of 25 Kgs each of earth enhancing compound. The chemical compound should be tested and certified by any NABL accredited laboratory with 95 percent carbon content. The testing laboratory should be an ISO 9001 and 14001 certified. The earth enhancing compound should be IEC 62321. The ph value of compound should be 7 -8. Electrode should be duly tested and certified by CPRI. Govt of India for a min short circuit current of 25 KA rms for 1 Sec. including necessary boring of suitable dia upto required depth in any type of soil for inserting copper rod and filling of chemicals and Poly plastic pit cover of material- polymerbody & cover dimensions-308mm (L) x 308 mm (W) x 214 mm (H) bearing capacity 7.5 Ton approved from NABL approved Lab Complete all as specified and as directed.Note (i) Earthing is to be done infront of the Engr-in-charge.(ii) Test results of earthing to be submitted by the contractor for all earthings(iii) The Contractor shall have to give written guarantee for maintenance earth resistance of less than 1.0 Ohm for the period of 2 (Two) years after certified date of completion and shall be deposited 2000/- per earthing as security deposit for a period of two(2) Years.(iv) Failing to maintain resistance of earthing less than 1.0 Ohm, New earthing to be provided by the contractor with out any extra cost.(v) Necessary earth work, excavation shall be carried out in any type of soil strata, returning filling in and making good surrounding arae complete. |
| 34 | Supply and erecting steel tubular poles complete with cast iron base plate, finial taper plug , bolts Nuts & screws complete all as specified type 410SP 31 of 9 mtr long including painting of pole with one coat red oxide primer & two coats of aluminum paint & emedded portion shall be painted with two coat of black bituminous paint all as specified with following specifications:-(i) Excavation in trenches in any types of soil ,returning filling in & well ramming including watering and disposal of surplus soil to a distance not exceeding 50 mtr from the starting points.(ii PCC (1:4:8) type D2 using 40 mm graded crushed stone aggregate as in foundation bedding all as specified and directed .(iii) PCC (1:3:6) type C-2 using 40mm graded crushed stone aggregate as upto ground level.(iv) PCC (1:2:4) type B-2 using 20mm graded stone aggregate as in coping including necessary form work all as specified. |
| 35 | M&L for supply and fixing in air termination, single pointed copper rod 12 mm dia and 300 mm long all as specified and as directed |
| 36 | M&L in for test point terminal block made of gun metal or phosphorus bronze size 75x75x25 mm, drilled and screwed including 3 Nos 8 mm dia 25 mm long hex head screw all as specified and directed |
| 37 | M&L for copper strip 20x3.15 mm with saddles and fixing screws etc. for roof conductors and down conductors above ground |
| 38 | Supply and fixing in GI Pipe light grade, 50mm dia , galvanized, with all fittings complete all as specified and directed |
| 39 | Supply and Laying in trenches / fixed to wall/ drawn in pipe/duct/laid in floor XLPE insulated screened,PVC bedded and sheathed and steel wire/strip armoured cable 1100V grade with stranded aluminum conductor of cross sectional area 50 Sq mm 3.5 core complete all as specified and directed. |
| 40 | Excavation in trenches, n exc 1.5m wide and n exc 1.5m in depth , for foundation, etc or for shafts, wells, cesspits, manholes, pier holes, laying of cables etc. n exc 10sqm on plan and n exc 1.5m in depth and getting out in any type of soil complete all as directed at site. |
| 41 | Supply and fixing of DWC pipe dia 50/38 mm (outter/inner) with including fitting like couplers, bends, and end caps and etc consists of two layer. The outer layer is correcgated for high diametrical stiffness, while the inner layer is plain and smooth to facilitate easy cable pulling. Primarily used for underground cable ducting for electrical networks to provide mechanical protection with standards IS:16205 (Part-24) 2017 all as specified and directed by Engr in charge. |
| 42 | M/L for Returning , filling in, including spreading, leveling, watering and well ramming in layers not exc 25 cm complete all as specified and as directed. |
| 43 | Supply and fixing in Street light fitting with new generation energy saving environemental friendly long life LED street light made up of pressure die cast aluminium housing with lens, energy efficient high quality consistency, glare control with toughned glass and individual high power LEDs with secondary optics ,IP66 protection and impact of capacity 35 Watt complete all as specified and directed by Engineer-in-charge. Please Enable Macros to View BoQ information |
AI Tender Summary
Tender Timeline
Jul 06, 2026
11:30 IST
Tender Published
Tender notice published.
CompletedJul 20, 2026
17:00 IST
Bid Submission Deadline
Online submission via eProcurement portal.
Upcoming · 10 daysJul 22, 2026
Bid Opening Date
Technical bids will be opened and evaluated.
Upcoming · 12 daysTender Documents
Download All (ZIP) ↓
Disclaimer
We takes all possible care for accurate & authentic tender information. However users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender