Tender For Repairs, Maintenance And Additional Alteration Of Quarter No. C-29 Office Of The Dig Ssb Zone Jodhpur Based On Pwd Integrated Bsr 2022 And .Electrical Bsr 2022 Rajasthan
Tender Value
48.34 Lakhs
Estimated cost
Bid Submission
14 Jul 2026
3 days left
EMD
96680
Bank guarantee accepted
Document Fee
1180
Non-refundable
Tender Type
Online
Tender Overview
Organization
Tender ID
Competition Type
NCB
Bidding Type
Tender
Location / State
Jodhpur → Rajasthan
EMD Exemption
Available
Quantity
Not Available
Website
Contact Person
Address
Project Description
Tender for Repairs, Maintenance And Additional Alteration Of Quarter No. C-29 Office Of The Dig Ssb Zone Jodhpur Based On Pwd Integrated Bsr 2022 And .Electrical Bsr 2022 Rajasthan
BOQ
| Sl. No. | Item Description |
| 1 | Earth work in excavation by mechanical means (Hydraulicexcavator )/ manual means over areas (exceeding 30cm indepth. 1.5m in width as well as 10 sqm on plan) includingdisposal of excavated earth, lead upto 50m and lift upto 1.5 m, disposed earth to be levelled and neatly dressed : All kindsof soil |
| 2 | Clearing jungle including uprooting of rank vegetation, grass,brush wood, trees and saplings of girth upto 30 cm measuredat a height of 1 m above ground level and removal of rubbishupto a distance of 50 m outside the periphery of the areacleared. |
| 3 | Demolishing lime concrete manually/ by mechanical meansand disposal of material within 50 metres lead as per directionof Engineer-in-charge. |
| 4 | Dismantling doors, windows and clearstory windows steel or wood shutter including chowkhats and holdfasts etc. complete and stacking within 50 meters lead : Of area 3 square meter and below. |
| 5 | Demolishing lime concrete manually/ by mechanical meansand disposal of material within 50 metres lead as per directionof Engineer-in-charge. |
| 6 | Dismantling old plaster or skirting, raking out joints andcleaning the surface for plaster including disposal of rubbishto the dumping ground within 50 meter lead. |
| 7 | Grading roof for water proofing treatment with water proffing compound :-Cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size) |
| 8 | Providing gola 75x75 mm in cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 stone aggregate 10mm and down gauge) including finishing with cement mortar 1:3 (1 cement : 3 fine sand) as per standard design : |
| 9 | Making khurras 450 x 450mm with average minimumthickness 50mm cement concrete 1 : 2:4 over P.V.C. Sheet 1Mtr. x 1 Mtr. x 40micron finished with 12mm cement plaster1 : 3 and one coat of neat cement, rounding edges andmaking and finishing the out let complete. |
| 10 | Providing & laying broken glazed titles on roof ( brokenglazed tiles not less than 9 Kg/Sqm) on top of hot bitumen @1.7 Kg/Sqm. (1.40 Kg of VG-40 (30/40 )grade and 0.30Kg/Sqm. Of VG-10 (80/100) grade) and joints filled withcement mortar 1 :2 (1 cement:2 marble dust mixed with waterproofing compund all complete as per direction of Engineerin-charge.: |
| 11 | Cement concrete flooring grade 1:2:4 (1-Cement:2-Coarse sand:4-graded stone aggregate) rounding off edges etc. but excluding the cost of nosing of steps etc. complete IS 2571-1970 : 50 mm thick with 20 mm thick nominal size aggregate.40mm thick with 20mm thick nominal size aggregate. |
| 12 | Plaster on new surface on walls in cement sand mortar 1:6 including racking of joint etc. complete fine finish :20 mm thick |
| 13 | Pointing on stone slab ceiling with cement mortar 1:2 (1 cement : 2 fine sand): Flush/ Ruled pointing |
| 14 | Pointing on stone masonry in cement sand mortar 1:3 (1 cement : 3 sand) :Deep groove pointing |
| 15 | Providing and applying white cement based putty over plastered surface to prepare the surface even and smooth complete :- New Plastered Surface (three or more coats) |
| 16 | Distempering with oil bound washable distemper of approvedbrand and manufacture to give an even shade including allscaffolding:12.37.1 New work (two or more coats) over and includingscrapping and priming coat with cement primer |
| 17 | Kota stone slab flooring 25 mm thick over 20 mm (average) thick base laid over and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete with base of cement mortar 1 : 4 (1 cement : 4 coarse sand) :- For area of each slab from 2001 to 5000 Sq.Cm |
| 18 | Kota stone slabs 25 mm thick in risers of steps, skirting, dado and pillars laid on 12 mm (average) thick cement mortar 1:3 (1 cement 3 coarse sand) and jointed with grey cement slurry mixed with pigment to match the shade of the slabs, including rubbing and polishing complete :-For area of each slab from 900 Sqcm |
| 19 | Providing and fixing 1st quality MAT finished ceremic tile size 300x300mm confirming to IS : 13755 and IS : 15622 colour such as white, grey, ivory, fume red brown, light green, light blue and other light shades in floors, steps, pillars etc. laid on a bed of neat cement slurry finished with flush pointing in the white cement mixed with pigment to match the shade of the tile complete (including the cost of cement mortar bed 1:4). |
| 20 | Providing and fixing 1st quality standard white, grey, ivory, fume red brown, light green, light blue and other light shades glazed tiles confirming to IS : 13753 & IS :15622 of size 200mm x 300mm in walls, floors, steps, pillars etc. laid on a bed of neat cement slurry finished with flush pointing in the white cement mixed with pigment to match the shade of the tile complete (excluding the cost of cement plaster on walls and pillar). |
| 21 | Providing and fixing T-iron frames for doors, windows and ventilators of mild steel Tee-sections, joints mitred and welded with 15x3 mm lugs 10cm long embedded in cement concrete blocks 15x10x10 cm of 1:3:6 (1 cement : 3 coarse sand : 6 graded stone aggregate 20 mm nominal size) or with wooden plugs and screws or rawl plugs and screws or with fixing clips or with bolts and nuts as require including fixing of necessary butt hinges and screws and applying a priming coat of approved steel primer. |
| 22 | Providing and fixing M.S. sheet 1mm thick single leaf door shutter in angle iron frame 35x35x5mm suitabilly diagonally braced with 25x3mm flat iron above and below lock rail of size 50x5mm beading extra including all fittings, as per direction of Engg. incharge but excluding cost of chowkhats: including two coats of anit-corrosive red oxide primer paint. |
| 23 | Providing and fixing steel glazed window frame made out of 80x40 mm hollow sheet section of 16 gauge thickness, joint mitred welded and grinded including hold fast of steel lugs 13mm x 3mm and 15 Cm long embedded in C C block 15 x 10 x 10 Cm of 1:3:6 nominal concrete and including fixing of pivoted hinges of superior quality, window shutters made out of 50 x 25.0 mm hollow steel section 15 mm paitam of 18 gauge thickness, joint mitred and grinded including 10mm x 10mm square bars welded to frame for paitam fixing float glass 4mm thick panes with glazing clips and metal sash putty and fixing of shutters frames peg stay, U shape handle 100 mm long, tower bolts 100 mm long of steel powder coated superior quality including fixing and jointing with frame hinges priming coat with steel primer complete in all respect as per direction of Engineer-in –charge :- Window openable. |
| 24 | P & F 1st qualityVitrified Porcelain Polished tiles on floor,skirting and steps etc.in different sizes (thickness to bespecified by manufactuer) with water absortion less than0.08% and conforming to IS 15622 of approved make in allcolour and shade, laid with 20 mm thick CM 1 : 4 includinggrounting the joints with white cement and matching pigmentetc complete. size 600 mm X 600 mm |
| 25 | S&f fixed wire gauge of stainless steel of 14 mesh x 24 gauge to the aluminium window by Aluminium beading 20x3mm with suitable screws at not exceeding 150mm distance at all heights with all lead and lift with scafolding. |
| 26 | Painting with synthetic enamel paint of approved brand and manufacture to give an even shade : Two or more coats on new work |
| 27 | Renewing glass panes with wooden fillets wherever necessary: 4mm thick plain glass panes. |
| 28 | Renewing glass panes,with putty and nails wherever necessary Float glass panes of thickness 4 mm |
| 29 | Providing and fixing fully panelled/partly panelled/ doubleleaf shutter frames for doors as per approved design anddrawings with approved ordinary C.P./ oxidised steel fittingsas per Annexure - 'A' and width of styles & top rails of 100mmand lock rails width of 150mm and bottom rails of 200mmwidth including teak wood beading of size 19mm x 12mm onboth faces complete :8.4.1 30 mm thick Shesham wood grade I |
| 30 | Providing and fixing external grade board solid core singleleaf flush door shutters ISI 2202-67 marked using Phenolformal dehyderesin in glue both sides with approved steelfittings complete as per annexure 'A' :30 mm thick . Commercial Veneer both side |
| 31 | Replacement of stone Chajja with sriwan in damaged portionas per existing thickness and width in CM 1 : 3 with removalof old damaged pieces of chajja including top plaster of chajjaand bottom pointing in CM 1 : 3 with scoffolding uptoGround floor level as per direction of Engineer in charge |
| 32 | Providing and laying cement concrete including curing,compaction etc. complete in retaining walls, return walls,walls (any thickness) including attached pilasters, columns,piers, abutments, pillars, posts, struts, buttresses, string orlacing courses, parapets, coping, bed blocks, anchor blocks,plain window sills, fillets, levelling course etc up to floor fivelevel excluding the cost of centering and shuttering.M10 grade Nominal Mix1: 4: 8 (1 cement : 3 coarse sand : 6 graded stone aggregate20mm nominal size). |
| 33 | Random Rubble stone masonry for with hard stone infoundation and plinth in Cement Sand mortar above 30 CMthick wall in:Cement Mortar 1:3 ( 1-Cement : 3-Sand). |
| 34 | Random Rubble stone masonry with hard stone insuperstructure above plinth level and upto five level above30cm. thick walls in :Cement Mortar 1:6 ( 1-Cement : 6-Sand). |
| 35 | Extra for facing as per design and detailed specifications IS 1597 (Part-II) 1992 including additional cost of stones over item No. 6.1 & 6.2 for : Course rubble facing Second Sort. |
| 36 | Finishing wall with water proofing cement paint of approvedbrand and manufacture and or required shade to give an evenshade including all scaffolding:12.41.1 New work (Two or more coats applied @ 3.84 kg/10 sqm). |
| 37 | Supplying and fixing machine cut fine dressed Red/Pink sandstone dasa or coping, with full moulding if required laid oncement mortar 1:4 including pointing with admixture ofpigment matching with the stone shade.50 mm thick |
| 38 | Providing and fixing Granite stone slab mirror polished and machine edge cut in Walls, Pillars, Steps, Shelves, Sills, Counters. Floors etc. laid on 12mm (Av.) thick base of cement mortar 1:3 jointing with white cement mortar 1:2 (1 white cement: 2 marble dust) with pigment to match the shade of the marble slab complete including grinding, rubbing and polishing of IS 3316-1974 : Jhunjhunu / Jalore (Red/Choclate/Black/Pink Colour) 1501 Cm2 to 3600 Cm2 Tiles |
| 39 | Providing corrugated G.S. sheet roofing including vertical /curved surface fixed with polymer coated J or L hooks, boltsand nuts 8 mm diameter with bitumen and G.I. limpetwashers or with G.I. limpet washers filled with white leadand including a coat of approved steel primer and two coatsof approved paint on overlapping of sheets complete (uptoany pitch in horizontal/ vertical or curved surfaces)excluding the cost of purlins, rafters and trusses andincluding cutting to size and shape whenever required. 0.63 mm thick with zinc coating not less than 275 gm/m2 |
| 40 | Carriage of earth, sand, lime, morrum, mannure or salb etc. including loading, unloading & staking as per specification etc. complete with lead of 10 Km.(B) Building Rubish Stone metal (Grit and Ballast etc.) |
| 41 | Repair of door, window shutters including cost ofmaterial and labour for change of damaged : |
| 42 | Panel by Wire Gauge 14 mesh x 24 gauge |
| 43 | Panel by Plain Glass Panes 4mm thick |
| 44 | Aldrop of mild Steel(i) 12\\" long x12mm dia |
| 45 | 8\\" long x 10mm dia |
| 46 | Door Springs of mild Steel |
| 47 | Steel Hinges (ii) For Wooden Chowkhat 4\\" size |
| 48 | Steel Handle 6\\" size |
| 49 | Mild Steel Tower Bolt 6\\" long |
| 50 | Providing & laying Chequered terrazzo tiles of approved make 22mm thick with marble chips of size upto 6mm, in floors,jointed with neat cement slurry mixed wit pigment to match the shade of tiles including rubbing and polishing complete inall respect as per specification, on 28mm thick bed of C.M. 1:4 Dark shade using ordinary cement. |
| 51 | Providing and fixing of double leaf steel shutter for cupboard, the frame is made of pressed steel ISI section 80x25 mmx 1.25 mm thick with 1.00 mm MS sheet to spot welded including holdfasts of 15x3mm, MS oxidized fittings such asbutt hinges, sliding doors bolts, handles, tower bolts and twin peg etc complete including applying priming coat of approved steel primer of red oxide zinc chromate and spray painting inapproved shade with deco paint of approved quality completeas per direction of Engineer In Charge |
| 52 | Providing and fixing Almirah lock (50 to 70 mm size )of approved make without pair of handles for door with necessary screws etc complete as per direction of Engineer-in-charge. |
| 53 | Structural steel work riveted, bolted or welded in built up sections, trusses and framed work, including cutting, hoisting(height upto 10 m) , fixing in position and applying a primingcoat of approved steel primer all complete: |
| 54 | Providing and laying of paver block as per IS 15658 : 2006(Indian standard for precast concrete block for pavingspecification)and IRC : SP:63-2004 (guidelines for the use ofinterlocking concrete block pavement) M-30, 60 mm thick to be used in non traffic areas like buildingpremises, monument premises, land scapes, public gardens/park, domestic drives, paths and patios, Embankment slopes,sand stabilization Area etc.( As per table 1 of IS 15658:2006 (B) Category „B‟ Denated only two side like I,Z,T shape etc. asper IRC SP 63:2004 |
| 55 | Providing and fixing 14 mm thick Acoustical with finefissured tiles/ Mineral fibre high density tiles with butt edgesfalse ceiling tiles of size 595x595 mm in true horizontallevel suspended on inter locking metal grid of hot dippedgalvanised steel sections ( galvanized @ 170 gsm/sqm.)consisting of main “T” runner with suitably spaced joints toget required length and of size 24x38mm made from 0.30mmthick (minimum) sheet spaced at 1200mm center to centerand cross “T” of size 24x25mm made of 0.30mm thick(minimum) sheet, 1200mm long spaced between main “T” at600mm center to center to form a grid of 1200x600 mm andsecondary cross “T” of length 600mm and size 24x25mmmade of 0.30 mm thick (minimum) sheet to be interlocked atmiddle of the 1200x600mm panel to form grids of 600x600mm and wall angle of size 21x21x0.30mm and laying false ceiling tiles of approved texture in thegrid including, wherever, required, cutting/making, openingfor services like diffusers, grills, light fittings, fixtures, smokedetectors etc. Main “T” runners to be suspended from ceilingusing GI slotted cleats fixed to ceiling with 6 mm dia and50mm long dash fasteners, 4mm GI adjustable rods withgalvanised level clips spaced at 1200mm center to centeralong main T, bottom exposed width of 24mm of all Tsectionsshall be pre-painted with polyester paint, allcomplete at all heights as per specifications drawings and asdirected by Engineer-in-Charge. ( The tiles should of 90 %RH avg. NCR 0.55 light reflectance> 80% thermalconductiveity K = 0.052-0.057 w/m K colour white. Fireperformance class 0/class I(BS 476) with warranty againstsag) |
| 56 | Labour charges for repair to door / window without using anymaterial such as applying randha (finishing) tightening of bolts& screw etc. |
| 57 | P & F European type white glazed vitreous china 1st quality Double syphonic W.C (IS :2556 Mark) with P or S trap including cutting and making good the wall and floor |
| 58 | P & F Premium quality water closet Seat Covers with brass hinges complete Solid PVC (ISI marked) grade-I White for EWC. |
| 59 | P & F Premium quality Low level Flushing Cistern of 10 litres capacity (IS:2556 mark) of approved make as per Engineer-in-charge with complete fittings C.I. brackets duly painted, brass ball cock with ball, (IS:1703 mark) complete including cutting and making good the wall :WVC with C.P. brass bend. |
| 60 | P & F WVC Wash basin (Ist quality IS:2556 Mark) of approved make with C.I. brackets duly painted 1 No. 15 mm C.P. Pillar cock (IS:8934 Mark) & 32 mm C.P. brass waste coupling of approved make, P.V.C Waste pipe with PVC nut 32 mm complete including cutting & making good the wall :Size 550 mm x 400 mm |
| 61 | P & F lst quality WVC Urinal (IS:2556 mark) with 25mm dia G.I. waste pipe, dome waste couplings, concealed iron brackets or screws etc complete. |
| 62 | Flat Back (large) or half stall size 610x400x80mm. |
| 63 | P & F C.P. brass Urinal Flush Pipe set complete with flanged brackets of approved make. |
| 64 | For 2 Urinals |
| 65 | P & F C.P. brass Urinal Spreader for stall urinal of approved make. |
| 66 | P & F Marble Urinal Partition slab both sides polished of approved design cut from marble size 900x600mm. IS 2556 (Part VI Sec.4)- 1995.Makrana 'Adanga' or Raj Nagar ISt Quality White or Andhi Indi-Italian marble |
| 67 | P & F Jet spray for water closet with C.P. Copper Tube flange of approved make. |
| 68 | P & F Bib Cock (IS : 8931 Mark), Superior quality of approved make: |
| 69 | C.P. Brass bib cock,15mm nominal bore. |
| 70 | (-do-) Long body, 15mm nominal bore weight not less than 690 gm |
| 71 | P & F Stop Cock (IS :8931 Mark), superior quality & of approved make: |
| 72 | C.P. Brass Concealed stop cock 15mm |
| 73 | Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply including all CPVC plain & brass threaded fittings i/c fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and the cost of cutting chases and making good the same including testing of joints complete as per direction of Engineer in Charge. (Concealed work including cutting chases and making good the walls etc.,) |
| 74 | (i) 20mm dia |
| 75 | (ii) 25mm dia |
| 76 | Providing and Fixing Unplasticized Poly Vinyl Chloride (UPVC) SWR Pipes Type B for sciland waste discharge system (IS:13592 : 1992 Marked) of approved quality /make |
| 77 | 75 mm dia |
| 78 | 110mm dia |
| 79 | Providing and Fixing Unplasticized Poly Vinyl Chloride (UPVC) SWR Pipes fittings type B for sciland waste discharge system (IS:13592 : 1992 Marked) of approved quality /make |
| 80 | Coupler |
| 81 | 75mm dia |
| 82 | 110mm dia |
| 83 | Bend 87.5 Dg. |
| 84 | 75mm dia |
| 85 | 110mm dia |
| 86 | Single 'Y' with Door |
| 87 | 75mm dia |
| 88 | 110mm dia |
| 89 | Door Bend 87.5 Dg. |
| 90 | 110mm dia |
| 91 | Single Tee |
| 92 | 75mm dia |
| 93 | 110mm dia |
| 94 | Single Tee with Door |
| 95 | 75mm dia |
| 96 | 110mm dia |
| 97 | Nahni Trap without Jali 4” |
| 98 | 110mm dia |
| 99 | Vent Cowel |
| 100 | 110 mm dia |
| 101 | P & F PVC Storage Tank ISI Marked (IS : 12701) indicating the BIS license No), of approved make with cover, 25mm dia 1M long G.I. over-flow pipe & 25 Cm. long wash out pipe with plug & socket, including making connection etc., complete of approved design: |
| 102 | 750 litres capacity. |
| 103 | P & F Full-way Valve (IS:778 Mark) or wheel valve of approved make : |
| 104 | Gun-metal 15mm nominal bore. |
| 105 | P & F Bevelled edge Mirror/mirror with teak wood lipping around of special glass of approved make as per direction of Engineer-in-charge complete with 6mm thick commercial ply base fixed to wooden screws & washers. |
| 106 | Other sizes |
| 107 | Construction of chamber in all type of soil with 300 mm thick masonry in CM 1:6 m,10 cm thick C.C. 1:5:10 in foundation, 20mm thick insider plaster in Cm 1:6, finished with floating neat cement, 50mm thick M-15 grade C.C. flooring , earthwork etc. complete as per design including disposal of surplus earth within a lead of 50 mtr. |
| 108 | Inside size 300 X 300 mm depth upto 0.5 M Cement cover with frame. |
| 109 | -do- size 450 x 450mm depth upto 0.5 M Cement cover with frame |
| 110 | P & F Square-mouth gully trap `A` grade (IS 651-1992 :marked) of approved make complete with C.I. grating, frame & Cover masonary chamber in C.M. 1:6, 100mm thick C.C. 1:5:10 base concrete, 40mm thick C.C.M-15 grade coping, 12mm thick cement plaster in CM 1:3 complete as per approved design & type. |
| 111 | Trap size 225 X 150 mm, ferrow cement cover with frame Internal Chamber size 450 X 450mm. |
| 112 | Construction of Cement Concrete Chamber 125mm dia. |
| 113 | C.P. Brass grating |
| 114 | Construction of soakage well in all type of soil with 300 mmthick dry masonry, top and bottom 300 mm course in CM 1:6,80mm thick stone slab, jointing of slab in CM 1 : 3, Ralthal,Kharanja, 40 mm thick M-15 grade C.C flooring , earthworkcomplete as per approved drawing including disposal of earthwithin a lead of 50 mtr.: Size 300 Cm. dia outside & 300 Cm. depth . |
| 115 | P & F Towel Rail or Ring of approved quality/make:C.P. brass Towel Rail elbow type with concealed screws size600 mm (Heavy duty). |
| 116 | Labour Charges for removing WVC pan: Indian/Orissa pan |
| 117 | P & F 1st quality WVC pedestal for wash basin. |
| 118 | P & F Indian type white glazed vitreous china 1st quality W.C.orissa pan (IS :2556 Mark) with 100 mm vitreous china P or Strap including cutting and making good the wall and floor: Size 530x410mm. |
| 119 | P & F Soap Dish or Tray of approved quality/make C.P. brass |
| 120 | P & F Shower arm 15mm dia of approved quality/make. C.P.brass heavy & superior quality 370mmProjection. size 370mm |
| 121 | P & F Bath Shower of approved quality/make. C.P. brass of Heavy & superior quality, revolving withadjustable key 150mm. |
| 122 | Providing and fixing Superior quality CP Brass fittings ofapproved make as per direction of Engineer-in-charge Two way Bib Cock 15 mm nominal size |
| 123 | Wiring of light point/ fan point/ exhaust fan point/ call bell point with 1.5 sq. mm nominal size FR PVC insulated unsheathed flexible copper conductor 1.1 kV grade and 1.5 sq. mm nominal size FR PVC insulated unsheathed flexible copper earth conductor 1.1 kV grade (IS:694) in recessed ISI marked MMS ( IS:9537 P - III ) virgin material PVC conduit & it's ISI marked (IS:3419-1988) accessories, round tiles, 1.2 mm thick Hot Dipped Galvanized Modular Box with earth terminal, 10A Modular switch,Modular face plate with grid plate, 3 pin ceiling rose / Holder /3 way connector, screws, making connections, testing etc. as required. For specification of copper Conductor, Phenolic Laminated sheet's & Electrical/ Wiring accessories refer Chapter E - 04, E - 05 & E - 07 For additional technical parameters of product / work refer Annexure 'A' attached with this BSR |
| 124 | Short point (up to 3 mtr.) |
| 125 | Medium point (up to 6 mtr.) |
| 126 | Long point (up to 10 mtr.) |
| 127 | Description Wiring of 3/5 pin 6 amp. Light plug point with 1.5 sq. mm nominal sizeFR PVC insulated unsheathed flexible copper conductor 1.1 kV grade and 1.5 sq. mm nominal size FR PVC insulated unsheathed flexible copper earth conductor 1.1 kV grade(IS:694) in recessed ISI marked MMS ( IS:9537 P - III ) PVC conduit & it's ISI marked (IS:3419- 1988)accessories, Hot Dipped Galvanized Modular box of 1.2 mm thick with earth terminal, 10 A modular switch, 3/5 pin 6 A modular socket, Modular face plate with grid plate, screws, making connections, testing etc. as required. For specification of copper Conductor, Phenolic Laminated sheet's & Electrical/ Wiring accessories refer Chapter E - 04, E- 05 & E - 07 For additional technical parameters of product / work refer Annexure 'A' attached with this BSR |
| 128 | On board |
| 129 | Supplying and fixing of power plug point with Modular accessories as perPWD specification for electrical Works, on hot dipped galvanized modularbox of 1.2 mm thick with earthing terminal/connector on surface or inrecessed with suitable size of modular face place with grid plate and coverplate including cost of ISI marked modular 16 amp. Switch (IS :3854) and 6/16 amp. socket outlet (IS:1293) making connection , testing , etc. asrequired. For specification of Wiring accessories refer Chapter E - 07related item & For additional technical parameters of product / work referAnnexure 'A' attached with this BSR |
| 130 | Providing & Fixing of IP20 SMD Mid Power LED batten type integrated light fixture made from Powder coated Extruded aluminium housing with in built driver , System lumen efficacy ≥ 110 lm/Watt output, internal surge protection of 2.5 KV with Short & Open circuit protection ,THD < 10% , P. F.≥0.95, CRI >80 , life time of minimum 50000 Burning Hours with , 70% of intial Lumen maintaned till life ends , CCT 3000°K / 4000°K / 5700°K /6000°K/6500°K (As per ANSI Bin) , Maximum power consumption should not more than the specified rating and Fixture shall be of BIS standard and trade mark certificate ( T.C.). Manufactures Word Mark/ Name Engraved/ Embossing/ Screen printing on housing. OEM must have its own in house NABL lab setup for all testing facilities for LED fixtures. (LM79 & LM80) certificate / Report from OEM shall be submitted. All as per pre approved by Engineer in charge. For additional technical parameters of products/ work , refer Annexure \\"A\\" attached with this BSR . |
| 131 | 1170mm(+/-10%) LED batten with min. lumen output 2200 lm |
| 132 | Providing & Fixing of Recessed/surface mounting heavy duty horizontal type Double Door ( Metal / Glazed )Distribution board with Metal end box made out from Galvanized steel / CRCA sheetnot less then 1.2 mm thick conforming to IS-8623-1 & 3 / IEC61439- 1 & 3, powder painted complete with reversible door (fordouble door DB only )100 amp. insulated copper bus bar/shortinglink , copper neutral link, copper earth link , color codedinterconnecting wire set of suitable rating and dinbar,maskingsheet, making internal DB terminations with copper lugs, Ferrules,detachable gland plate, including making connections, testing etc.as required. OEM shall have submit NABL / CPRI / ERDA accrediatedlab type test reports & All as per pre approved by Engineer incharge. For additional technical parameters of product / work referAnnexure 'A' attached with this BSR |
| 133 | Metal door (single phase) IK-09 and IP-43 with Metal end box |
| 134 | 8 Way (8+2) |
| 135 | Metal door (Three phase) IK-09 and IP-43 with Metal end box |
| 136 | 8 Way |
| 137 | Providing & Fixing of 240/415 V AC MCB with positive isolation of 10 kA breaking capacity (B/ C/D tripping characteristic as per type of load and site requirement) 4 KV impulse withstand voltage, ISI marked IS 8828(1996) / conforming to IEC 60898-1 2002, IEC 60947-2, low watt losses, trip free mechanisum , energy limiting of class 3 as per IEC, minimum phase termination capacity of 35sq.mm. , conductor line load reversibility , IP 20 contact protection and fitted in existing distribution board/sheets, minimum electrical operation 20,000 upto 20 A rating and 10,000 upto 63 A, 5000 for 80 A & above rating including making connections, testing etc. as required. OEM shall have submit NABL / CPRI / ERDA accrediated lab type test reports & All as per pre approved by Engineer in charge. For additional technical parameters of product / work refer Annexure 'A' attached with this BSR |
| 138 | Double pole MCB(With B/C curve tripping Characteristics) |
| 139 | 6 A to 32 A rating |
| 140 | Single pole MCB (With B/C curve tripping Characteristics) |
| 141 | 6 A to 32 A rating |
| 142 | Four pole MCB (With B/C curve tripping Characteristics) |
| 143 | 50/63 A rating |
| 144 | Supplying and drawing FR PVC insulated & unsheathed flexible copperconductor as per PWD specification for electrical Works with ISImarked (IS:694) and as per IS 8130 : 2013 of 1.1 kV grade . Wire shouldbe made from 99.90 % purity copper, class 5 stranding in acc. toIS:8130/IEC 60228 for lower watt loss , oxygen free for less chances of oxidization, insulation PVC type A/C/D , flame retardant as per IS 10810-53, better amperage rating as per IS:3961 part 5, in existing surface or recessed PVC/ MS conduit/casing capping makingconnections with Copper Lugs of suitable size, Ferrules,testing etc. asrequired. OEM Must have its own in house NABL lab setup for alltesting facilities for wires. For additional technical parameters ofproduct / work refer Annexure 'A' attached with this BSR |
| 145 | 2 x 2.5 sq. mm. + 1x1.5sqmm |
| 146 | 2 x 4.0 sq. mm. + 1 x 2.5 sq. mm. |
| 147 | 3x 1.5 sq.mm |
| 148 | 2 x 6.0 sq. mm. + 1 x 2.5 sq. mm. |
| 149 | 4 x 6.0 sq.mm |
| 150 | S&F following sizes (dia.) of ISI marked virgin material MMS ( IS:9537 P -III ) PVC conduit along with ISI marked (IS:3419-1988) accessories asrequired in recess including cutting the wall, covering conduit andmaking good the same as required. For additional technical parametersof product / work refer Annexure 'A' attached with this BSR |
| 151 | 20 mm |
| 152 | 25 mm |
| 153 | 32 mm |
| 154 | Providing & Laying P.V.C. / XLPE insulated & P.V.C. sheathed Un-ArrmouredAluminium cable confirming to IS:1554 P-I / IS :7098 P - I of 1.1 KV with H4-Grade electrolytic aluminium conductor confirming to IS 8130 of purity >99.6 %,Inner / outer sheath confirming to IS:5831 in existing RCC / Hume / Stoneware /PVC pipe/ open duct/cable trench / Cable tray (with cable tie) including testingetc. as required of following size. OEM must have it's own in house NABL accrediated Laboratory for testing procedure as per IS:10810. For additionaltechnical parameters of product / work refer Annexure 'A' attached with this BSR |
| 155 | 6.0 Sq. mm |
| 156 | 2 core |
| 157 | 10.0 Sq. mm |
| 158 | 2 core |
| 159 | 4 core |
| 160 | Providing & Laying P.V.C. / XLPE insulated & P.V.C. sheathed Arrmoured Aluminium cable confirming to IS:1554 P-I / IS :7098 P - I of 1.1 KV with H4- Grade electrolytic aluminium conductor confirming to IS 8130 of purity >99.6 %, round / flat strip armouring of cables, Inner / outer sheath confirming to IS:5831 in existing RCC / Hume / Stoneware / PVC pipe/ open duct/cable trench / Cable tray(with cable tie) including testing etc. as required of following size. OEM must have it's own in house NABL accrediated Laboratory for testing procedure as per IS:10810.For additional technical parameters of product / work refer Annexure 'A' attached with this BSR |
| 161 | 16.0 Sq. mm |
| 162 | 4 core |
| 163 | Providing & Fixing of energy efficient /energy saving IP 20 LED direct retrofit Bulb inexisting holder or fixture as required with system lumen efficacy ≥100 lm/Watt output ,pf0.95 , CRI >70, minimum life time of minimum 25000 Burning Hours with , 70% of intialLumen maintaned till life ends , CCT 3000°K / 4000°K / 5700°K /6000°K/6500°K (As perANSI Bin) , maximum power consumption should not more than the specified rating and Fixture shall be of BIS standard and trade mark certificate ( T.C.). Manufactures WordMark/ Name Engraved/ Embossing/ Screen printing on housing. OEM must have its own inhouse NABL lab setup for all testing facilities for LED fixtures. (LM79/LM80) certificate /Report from OEM shall be submitted. All as per pre approved by engineer in charge . foradditional technical parameters of product/ work, refer Annexure \\"A\\" attacheded with this BSR |
| 164 | 9 Watt |
| 165 | Providing & Fixing of of Double ball bearing, copper wounded capacitorstart single phase metallic blade fresh air fan, in existing openingincluding cost of hardware , flexible 3 core copper conductor ,makingconnections, testing etc. as required. All as per pre approved by Engineerin charge. For additional technical parameters of products/ work , referAnnexure \\"A\\" attached with this BSR |
| 166 | 300 mm sweep |
| 167 | Providing & Fixing of Heavy duty capacitor start, copper wound Doubleball bearing 900/1400 RPM single phase Exhaust fan conforming toIS:2312 ISI marked in existing opening including making connectionstesting etc. as required. All as per pre approved by Engineer in charge.For additional technical parameters of products/ work , refer Annexure\\"A\\" attached with this BSR . |
| 168 | 300 mm sweep(900/1400 RPM) |
| 169 | Plate Earthing as per IS:3043 with copper Earth plate of purity >95% ofsize 600mm x 600mm x 3.0mm by embodying 3 mtr. below the groundlevel with 20 mm dia. G.I. 'B' class watering Pipe ,including all accessorieslike nut, bolts, reducer, nipple, wire meshed funnel, and Heavy dutyweather proof poly-propylene earth pit chamber with lockable Jam freelid suitable for safe working load 5000 Kg or more of size Top Dia. 225 to260 mm, Bottom Dia 300 to 350 mm. and Height 250 to 300 mm.andembodying the pipe complete with alternate layers salt and coke/charcoal, testing of earth resistance for value of 5 ohms or less asrequired & must record by engineer in charge during site visit and ensureto enter in measurment book. All as per pre approved by Engineer incharge. For additional technical parameters of products/ work , referAnnexure \\"A\\" attached with this BSR . |
| 170 | Supply and installation of high tensile low carbon steel rod molecularlybonded with 99.9 % Copper thickness (250 microns) and confirming toUL 467, IS/IEC 62561-2 of following size and length and as per pointmentioned (a), (b), [c), (d), (e) below :-(a) Bore a hole of dia. 100 mm of required length, Place the rod in thecentre of Hole |
| 171 | filled with anti corrosive conductive compounds with the permanentsealings at both the ends, CPRI/ ERDA tested with RMS capacity ofminimum 30 KA for withstanding 1 second .To ensure the moisturecontent and electrical conductivity, 25 kg for 2000 mm & 50 Kgs for3000mm of resistance lowering earth enhancement material shall beused as a backfill compound. The compound shall be tested form NABLacredeated lab for low resistivity ( less than 0.12 Ohm - meter ) & highconductivity in nature with carbon as a major content as per referance of IS 3043-1987,IEEE 80-2013 (clause 14.5d) , IEEE 837 & IER 1956 withlatest amendemnts |
| 172 | Connect the rod with copper Strip/Conductor/Wire with suitableclamp made from tinned copper and SS 304 BoltPlace Heavy duty weather proof poly-propylene earth pit chamberwith lockable Jam free lid suitable for safe working load 5000 Kg or moreof size Top Dia. 225 to 260 mm, Bottom Dia 300 to 350 mm. and Height250 to 300 mm. |
| 173 | Testing of earth resistance for value of 5 ohms or less as required &must record by engineer in charge during site visit and ensure to enter inmeasurment book. Test certificates for confirming above standards from OEM ismandatory. All as per pre approved by Engineer in charge. For additionaltechnical parameters of products/ work , refer Annexure \\"A\\" attachedwith this BSR . |
| 174 | 25 mm thick and 3 Mtr. Long |
| 175 | Supply & Laying following size earth wire in horizontal or vertical run in ground/surface/recess including riveting, soldering, saddles, making connection with GI/Cu purity purity >95% thimble etc. as required. All asper pre approved by Engineer in charge. For additional technicalparameters of products/ work , refer Annexure \\"A\\" attached with this BSR . |
| 176 | 8 SWG G.I. ( Hot Dipped ) Wire |
| 177 | 10 SWG copper. Wire |
| 178 | Providing & Fixing of IK08 IP-66 protected high power LED flood light system with single piece Pressurediecast aluminium housing, toughened glass diffuser with suitable lenses on LED to achieve various beamangles, of high power LED of 3 to 5 watt each . Integrated potted driver as a unique BIS R number havingefficiency more than 85 % and in compliance to BIS certified and Trade mark certificate. The System levelLuminaire efficacy >=125 lm/ wt. LED driver Input Voltage AC 120 to 270 V AC with High voltage Cutoff@>=300 V AC and Auto resetting Safety .Power Factor >0.95 , THD(I) <10% , driver current <=750mA.driver should be Phase to phase protectionof 440 V for 4 Hrs. Electrical Connector , Surge Protection Min>=4KV internal and 10KV external but inside driver compartment, System life of 50000 Burning hourswith 70% of Initial Lumens maintained, CRI>70 andCCT5700K355K.ManufacturesWordMark/NameEngraved/Embossing/Screen printing on die cast housing to allow traceability/authenticity. Fixture shallbe IS 10322 Complianced.OEM Must have its own in house NABL lab setup for all testing facilities for LEDfixtures. (LM79/LM80) Certificate/ report with liable warranty of product/accessories from OEM shallbe submitted. All as per pre approved by Engineer in charge. Foradditionaltechnical parameters ofproducts/ work , refer Annexure \\"A\\" attached with this BSR |
| 179 | High Power LED Flood Light Minimum lumen output 14800 lm |
| 180 | Providing & Fixing of BEE Star rated copper wounded double ballbearing capacitor start, aluminium body & Metallic blade ceiling fanConforming to all the performance requirements laid down in IS374:2019 including all amendments, as applicable ; & Carry BIS licensing(i.e. ISI marking) with down rod up to 80 cm with secondary supportsafety cable ( steel rope) , cotter pin with 3 x 1.5 sq.mm pvc insulatedflexible copper conductor making connection testing etc. as required. Allas per pre approved by Engineer in charge. For additional technicalparameters of products/ work , refer Annexure \\"A\\" attached with thisBSR . |
| 181 | 1200 mm Sweep BEE 3 Star rated (service value >=5.0 to< 5.5 ) |
| 182 | Providing & Fixing of modular type 120 W Step Fan regulator duly ISImarked (IS 11037:1984 ) with CM/L no. printed made out of unbreakableand fire retardant vergin poly carbonate with brass terminals and captivescrews & silver alloy contact tip with IP-20 rating , including all as per preapproved by Engineer in charge,making connections, testing etc. asrequired. For additional technical parameters of product / work referAnnexure 'A' attached with this BSR |
| 183 | 5 step fan regulator 2 Module 360 dgree rotating |
| 184 | Providing & Fixing of following modular accessories as per PWDspecification for electrical Works, made out of unbreakable and fireretardant vergin poly carbonate with brass terminals and captive screws &silver alloy contact tip with IP-20 rating , including all as per pre approvedby Engineer in charge,making connections, testing etc. as required. Foradditional technical parameters of product / work refer Annexure 'A'attached with this BSR |
| 185 | RJ-11 telephone jack single line |
| 186 | P & F Krone module with base frame in the recess / surface made out of1.2 mm thick sheet steel box, front openable, having locking arrangementsduly powder painted,including dressing, ferruling and punching oftelephone cable with krone tool etc. as required. For additional technicalparameters of product / work refer Annexure 'A' attached with this BSR |
| 187 | 10 Pairs |
| 188 | Providing & Fixing of extra down rod of 15 mm dia . ERW (Electricalresistance welded ) of 1.6mm nominal thick medium duty steel pipeincluding cutting, threading, drilling, fixing quarter pin etc as reqd. All asper pre approved by Engineer in charge. For additional technicalparameters of products/ work , refer Annexure \\"A\\" attached with thisBSR |
| 189 | Supplying and drawing PE Insulated & PVC Sheathed unarmoured telephone cable with 0.5 mm dia. Solid Annealed electrolytic gradebare Copper Conductor as per IS: 8130/84 &confirming to TECspecification GR / WIR/06-03 March 2002 in existing surface orrecessed conduit/casing capping. including ferruling on each pair forIdentification etc. as required. For additional technical parameters ofproduct / work refer Annexure 'A' attached with this BSR |
| 190 | 2 pair |
| 191 | 10 pair |
| 192 | Supply, Drawing and Testing of 4 pair, 23 AWG Solid Bare Copper wire insulated with PVC,UTP (Unshielded Twisted Pair), Category 6, Class E, 100 Ohm Impedance, Indoor Cable asper latest ammendments of ANSI/TIA/EIA-568 , The copper conductors should be balancedtwisted in pairs, seperated by a cross-member fluted pair divider & protected by PVCJacket. Certified performance in a 4-connector configuration upto 100 Mtrs channelrequirements & transmission frequencies up to 250 Mhz. in existing MS/PVCConduits/casing capping including making connections to Information outlets and PatchPanels with jack & ferruling at both ends for identification with necessary tools forpunching, stripping, crimping and testing etc as required complete in all respect. All as perpre approved by Engineer in charge. For additional technical parameters of products/ work, refer Annexure \\"A\\" attached with this BSR . |
| 193 | Supply & fixing of square Faceplate for Flush / Surface Mount Information OutletsSingle/Dual or Quad Aperture , material should be PC+ABS body, Suitable for RJ45unshielded/shielded connection modules. Should match with I. O. OEM. Dimensions shouldbe 86mm X 86mm as required complete in all respect. All as per pre approved by Engineerin charge. For additional technical parameters of products/ work , refer Annexure \\"A\\"attached with this BSR |
| 194 | Single Aperture |
| 195 | Supply, Installation, Testing and Comissioning of Rack mounted 19\\" 1U, Cat6 24 Port loaded, 1.5-1.6 MM CRS chasis, powder coated, sheet steel, made of plastic (ABS), ModularPatch Panels with Rear Cable management system and mounting hardware to mount thepatch panel. Should have port identification numbersprinted/engraved on front of thepanel. Etc. as required.All as per pre approved by Engineer in charge. For additionaltechnical parameters of products/ work , refer Annexure \\"A\\" attached with this BSR . |
| 196 | Modular Patch Panel Loaded with Cat -6 I/O |
| 197 | Supply , Installation and Testing of 4 pair, 100 Ohm impedance, Cat 6/6A /Class E/Ea patchcords should be constructed of minimum 23/24 AWG, stranded bare Copper cable withFRPVC/LSZH Jacket, with an enhanced performance by factory moulded RJ45 connectorswith strain relief boots as per ANSI/TIA/EIA 568-C.2 suitable for Cat 6/6A applicationcomplying to latest ammendments Category 6/6A Standards, According. to TIA568C.2,ISO/IEC 11801, EN 50173, IEC 60603-7-51, EN 60603-7, IEEE 802.3an minimum requirementfor 1G BASE-T to 10G BASE-T performance. Patch cords shall be straight thru cablecompatible with both T568-A and T568-B wiring schemes, should support IEEE 802.3af /IEEE 802.3at for POE applications, Minimum 750 to 1000 mating cycles in plug contacts forlong durability, Should support Ethernet 10GBASE-T, 1.2 Gb/s ATM, Token ring 4/16, Digitalvideo and broadband/baseband analog video, Voice over internet protocal (VOIP).All as perpre approved by Engineer in charge. For additional technical parameters of products/ work, refer Annexure \\"A\\" attached with this BSR . |
| 198 | Cat 6, U/UTP (Unscreened/Un-sheilded Twisted Pair) Patch Cord |
| 199 | 1 Mtr |
| 200 | Supply & Installation of IP-20 & IK-08 , UL Listed Wall mounted Double Section Communication enclosure (Rack) made from powder coated (60 to 80 Micron) CRCA sheet,front sturdy sheet steel frame folded from one piece and welded with minimum 5mmtoughened glass door,Vertical Mounting Rail 1.6 MM with 'U'Marking , with All roundprotective channel on the door aperture, lock integrated on front door, top and bottomcover with cable entry provision with gland plates, integrated side walls, 2 pair of 19\\" angleswith wall mounting provision on wall. Accessories like: 1 No of 19\\" 1U Horizontal Cablemanager, 1 No of 90 cfm 230V AC Fan with 1 mts long cable, mounting hardware , 1 No of19\\" 1U, mountable socket strips with 5 nos of 5A universal sockets with 2 mts long powerchord for supplying power to switches, fans etc along with earth continuity kit, indicator,moulded power supply cable. fixing on wall with Suitable Anchor fastner etc as required.Allas per pre approved by Engineer in charge. For additional technical parametersofproducts/ work , refer Annexure \\"A\\" attached with this BSR . |
| 201 | 9 U Rack with Width 600 mm & Depth 400 mm + 100 mm |
| 202 | 6 U Rack with Width 600 mm & Depth 400 mm + 100 mm |
| 203 | Supply , Installation, Testing and Comissioning of Managed Layer-2 Intelligent 10/100Ethernet Switch providing 24 x 10/100/1000 MBPS Giga Ethernet ports / with min 2 SFPGiga Ports (provision for Fiber Giga connectivity) with related LANBase Software includingmaking connections etc as required.All as per pre approved by Engineer in charge. Foradditional technical parameters of products/ work , refer Annexure \\"A\\" attached with thisBSR |
| 204 | Supply Installation, Testing and Commissioning of L2 managed Switch; 16X10/l00/1000 BASE-T port and with min 2x 1000/10000 BASE-X SFP (With 2 SFP module for fiber Giga Connectivity); Total power budget: minimum 300W, Switching Capacity 56 GBPS or better; MAC Table 8K or betters Rack mounting; Flow Control; QoS; 802.lQ Standard VLAN, Network Management; Wide working temperature: -05-55°C; Lightning Protection Common mode 4KV;Certificate of compliance: CE/FCC, including making connections etc. as required complete in all respect. All as per pre approved by Engineer in charge. For additional technical parameters of products/ work, refer Annexure \\"A\\" attached with P.W.D. Electrical B.S.R. 2022. |
| 205 | Supply and Installation of unsheilded/360 degree sheilded Information outlets made of highimpact plastic body with ABS, FR Grade halogen free material with provision for protectionagainst dust in jack, suitable for Cat 6/6A application complying to latest ammendments,According. to Cat. 6/6A channel, It should support channel as well as componentsrequirements of Cat.6/6A standards at frequencies of up to 250 to 500 Mhz. Cat 6/6Aunshielded/shielded Jack should be suitable to terminate 4 pair, 23/24 AWGsolid/strandedwire diameters, using 100 Ohm unshielded/shielded balance twisted pair cable, the jackshould have tooless/impact termination on reliable copper tin plated Insulationdisplacement contact, with easy lock mechanism, It supports IEC 60603-7-4 and compliedwith ANSI/TIA/EIA 568 C.2 standard. jack should be RJ11,RJ12 & RJ45 compatible. Shouldsupport Ethernet 1.2 Gb/s ATM,Digital video and broadband/baseband analog video, Voiceover internet protocal (VOIP) Specifications in existing modular/MS Boxes along withnecessory connections as required.All as per pre approved by Engineer in charge. Foradditional technical parameters of products/ work , refer Annexure \\"A\\" attached with thisBSR . |
| 206 | Cat 6, Un-sheilded Information Outlet |
| 207 | Providing & Fixing of Vertical(BEE 5 star rated) / Horizontal( BEE 3 starrated) storage water heater with outer casing made of EngineeringPlastic sheet (Upto 25 Ltr) / Metal rust proof Body (35 & 50 Ltr), Glass -line / Titanium Enamel coated Pressure Pump Compatible 8 bar pressureInner tank, Glass Line Coated , mineral filled heating element, stem type,snap action adjustable thermostat , Dual indicating lamps Injected PUFinsulation, Multi Function Valve etc. as required held in position with2/4 no. 10/12 mm anchor Fastener, duly wired with 3 core 2.5/4.0Sqmm PVC insulated & sheathed copper conductor and 16 A/25A threepin plug top with Portable Residual Current Device ( PRCD ) , includingmaking inlet, outlet Flexible alloy connection, testing etc. as required.All as per pre approved by Engineer in charge. For additional technicalparameters of products/ work , refer Annexure \\"A\\" attached with thisBSR . |
| 208 | 25 Ltr |
| 209 | Supply & Fixing of Dry Powder Agent (as per IS 4308:2019), ABC type FireExtinguisher (Stored Pressure type) conforming to IS:15683:2018 , Powdercoated Internal & External Surface Deep drawn cylinder body of Mild SteelCR2 grade conforming to IS: 513, Squeeze grip Forged brass release valve withInbuilt safety release device, Diaphragm Type, 0 to 28 bar range pressuregauge, 450 mm long EPDM discharge tube, QR code for Product Traceabilityincluding Fixing on wall with suitable Anchor Fasteners as required offollowing capacity. Test Certificates of all the Parameters along with Hydrotest & Burst test (For Cylinder Body) Certificate from OEM / External NABLAccrediated Lab is to be submitted. All as per pre approved by Engineer incharge. For additional technical parameters of products/ work , referAnnexure \\"A\\" attached with this BSR . |
| 210 | Providing & Fixing of IP-20 LED Recessed / Surface Mounted, Round / Sqaure SMD MidPower LED Downlight with power coated die-cast aluminum housing with UV Stabilizednon yellowish Diffuser with BIS complience 2.5 KV surge protected Isolated driver, withShort & Open circuit protection, having efficiency > 85% . System Lumen efficacy of ≥ 110lm / watt, THD < 10 % , Pf.≥0.95, CRI >80, life time of minimum 50000 Burning Hours with ,70% of intial Lumen maintaned till life ends , CCT 3000°K / 4000°K/ 5700°K/6000°K/6500°K (As per ANSI Bin) , maximum power consumption should not more thanthe specified rating and Fixture shall be of BIS standard and trade mark certificate( T.C.).Manufactures Word Mark/ Name Engraved/ Embossing/ Screen printing on housing.OEM must have its own in house NABL lab setup for all testing facilities for LED fixtures.(LM79 & LM80) certificate / Report from OEM shall be submitted. All as per pre approvedby Engineer in charge. For additional technical parameters of products/ work , referAnnexure \\"A\\" attached with this BSR . |
| 211 | Surface Mounting (with extruded alumn. Housing ) |
| 212 | Minimum lumen output 650 lm |
| 213 | P & F 1.2 mm thick G. I. / M .S. Sheet boxes duly finished with twocoats of red oxide and with earthing terminal of following sizes(nominal size) in recessed/surface as required.For additionaltechnical parameters of product / work refer Annexure 'A' attachedwith this BSR |
| 214 | 1.2 mm thick M. S. Sheet boxes |
| 215 | 75mm x 75mm x 60mm |
| 216 | SITC of 8 port Giga PoE Switch with dual uplink : unmanaged PoE switch; 8Xl0/100/1000 mbps Base-T PoE; 2*10/100/1000 Base-T(Uplink) or 2*1000 Base-X (uplink); PoE Power Consumption per Port: <=30W; power budget: minimum 96 W; PoE Protocols: IEEE 802.3af, IEEE 802.3 at ;Switch Capacity: 20 Gbps or better; MAC Table Size 2K or better; Working Temperature: -5°C-55°C; Power supply:DC48-57V Certificate of compliance: CF/FCC. A11 as per pre approved by Engineer in charge. For additional technical parameters of products/ work, refer Annexure \\"A\\" attached with P.W.D. Electrical B.S.R. 2022. |
| 217 | SITC of IR IP based 5 MP Bullet Camera 5 MP, Video Resolution: 2592(H)x1944(V) Pixels , 1 to @25 fps; Image Sensor: 1/2.8-inch CMOS; Built in Infra-Red: 40 to 50 Mtr; High Dynamic Range- 120 dB WDR; Lense- 2.8/3.6 mm, ;H264,H265/MJPEG, provision for Support on-board storage up to 256 GB (SD card not included) , intrusion detection, Line crossing detection, Motion detection, Dynamic analysis, Alarm should be trigger on (Tampering alarm, Network disconnect, IP address conflict, Storage exception), security feature such as (password protection, privacy mask, watermark, IP address filtering, anonymous access), Open standard to support ONVIF (PROFILE S, PROFILE G), Metal Housing, Vandal-proof housing IP 67, DC 12V & PoE, Complete with Junction box for cable management Oerating Conditions : -30°C to + 70 °C or better. Onvif Profile S, G, Confirmant; Model should be: CE, BIS,/UL, FCC, ROHS compliance The CCTV OEM should have CMMI Level 5 or above or equivalent setup certification. The CCTV OEM should have its office and service/ support center in Rajasthan. All as per pre approved by Engineer in charge. For additional technical parameters of products/work, refer Annexure \\"A\\" attached with this BSR. |
| 218 | Supply, Installation, Testing & Commissioning of 16 Ch NVR Pre-licensed, NVR supports up to 40 TB HOD Support, 16 Ch IP inputs; Support ANR technology; 320mbps incoming bandwidth, supports up to 12MP full channel recording; support H.265 compression; 16ch synchronized playback @1080p; support 3rd party cameras ONVlF type; 4K output; minimum 04 SATA HDD Slots; each slot should support up to 10 TB HDD; Dual gigabit self-adaptive Ethernet interface; serial interface; USB interface; (all cameras and Storage-NVR should be of same make for the smooth functioning of the system) complete with mounting accessories & junction box (to be provided by OEM) for cable management. Model should be: Certificates of Compliance: UL, CE/FCC, BIS. The CCTV OEM should have CMMI Level 5 or above or equivalent setup certification. The CCTV OEM should have its office and service/ support center in Rajasthan. All as per pre approved by Engineer in charge. For additional technical parameters of products/work refer Annexure \\"A\\" attached with this BSR. |
| 219 | Supply, Installation, Testing & Commissioning of 3.5\\" 6 TB SATA, USB 3.0 Surveillance Hard Disk. All as per pre-approved by Engineer in charge. For additional technical parameters of products/ work, refer Annexure \\"A\\" attachedwith this BSR |
| 220 | Providing & Fixing of IK08, IP 66 protected LED Street Light Luminaire on existing bracket/pole. Fixture made of powder coated single piece pressure die cast aluminum material with heat dissipation fins on housing with UV stabilized PC (UV stablization report submitted for UV cover ) /Toughened Glass cover and secondary lens on each LED & should be SMD type of 3 to 5 watt each . The System efficacy >=125 lm/ wt and potted driver & has a unique BIS R number with Input Voltage AC 120 to 270 V AC with High voltage Cutoff @>=300 V AC and Auto resetting Safety , Power Factor >0.95 driver Efficiency >85% ,THD(I) <10% Humidity 10% to 90% RH Working Temp -5C to 45C . driver current <750mA. The luminaire shall be BIS certified and Trade mark certified. Life Expectancy Equal or more than 50000 burning hrs with Minimum 70% lumen maintened , CRI >70 and CCT 5700K +355K. Surge protection shall be min ≥ 4 KV internal and min 10 KV external inside driver compartment. driver should be Phase to phase protection of 440 V for 4 Hrs. Manufactures Word Mark/Name Engraved/Embossing on die cast housing to allow traceability/authenticity. Fixture shall be AS PER IS 10322 Complianced.OEM Must have its own in house NABL lab setup for all testing facilities for LED fixtures. (LM79/LM80) Certificate/ report with liable warranty of product/accessories from OEM shall be submitted. All as per pre approved by Engineer in charge. For additional technical parameters of products/ work , refer Annexure \\"A\\" attached with this BSR . |
| 221 | LED Street Light fixture with Minimum lumen output 11225 lm |
| 222 | Providing & Fixing of IK08 IP65 protected Top/Bottom mounted LED Post top Luminarie made of single piece construction powder coated die cast alluminium housing with UV stabalized Clear / frosted Polycarbonate diffuser and Aluminium anodised with sand blast reflector. The System level Luminous efficacy ≥ 100 Lumen/W. SMD LEDs is to be used, System CRI>70, CCT: 3000/4000/6500 K. The integral electronic driver must be potted & has a unique BIS R number must be potted & has a unique BIS R number constant current and Internal/external surge protection device of min. 4KV(L-N) and efficiency > 85%, PF>0.9, THD<10% and input Voltage range of 140-270V AC at 50Hz. System life of 50000 Burning hours with 70% of Initial Lumens maintained . Driver current <750mA. Fixture must be in compliance with BIS Standards and Trade mark Certificate complete in all respect.OEM Must have its own in house NABL lab setup for all testing facilities for LED fixtures. (LM79/LM80) Certificate/ report with liable warranty of product/accessories from OEM shall be submitted. All as per pre approved by Engineer in charge. For additional technical parameters of products/ work , refer Annexure \\"A\\" attached with this BSR . |
| 223 | Minimum lumen output 2500 lm Post top Luminarie |
| 224 | Supply , Installation, Testing and Comissioning of Inverter type Air Cooled Hi Wall split type Air conditioners with latest star rating system as per BEE amended upto date complete with Indoor unit(IDU), Out door unit (ODU), surface / concealed copper Refrigerant piping with insulation (closed cell elastomeric nitrile rubber tubular pipe section) upto 3 Mtr (IDU to ODU), copper power cable upto 3.5 Mtr (IDU to ODU), R-32/R-410 Green Refrigerant, wireless Remote control, suitable for working between 230V +/- 10% with low & high voltage cutoff and 50 hz , single phase AC supply capable of performing cooling, dehumidification, air circulation of following capacity with Scroll / rotary compressor. All as per pre approved by Engineer in charge. For additional technical parameters of products/ work , refer Annexure \\"A\\" attached with this BSR . |
| 225 | 2.0 TR ISEER not less then 3.8 |
| 226 | Supply & fixing MS powder coated stand suitable for 1.0/1.5/ 2.0 Tr outdoor type of Split AC. All as per pre approved by Engineer in charge. For additional technical parameters of products/ work , refer Annexure \\"A\\" attached with this BSR . |
| 227 | Providing & Fixing of IS : 4985 - 2000 Class -4 (10 Kgf / Sqcm) UPVC drain water piping with fittings (IS:7834 & 10Kgf/sqcm) like elbow, socket, Tee, solvent cement jointing, support with MS hanger on ceiling or recessed in wall with chasing & plastering with 6 mm thick closed cell elastomeric nitrile rubber insulation including leakage testing etc. as required of following Nominal sizes. All as per pre approved by Engineer in charge. For additional technical parameters of products/ work , refer Annexure \\"A\\" attached with this BSR . |
| 228 | 25 mm |
| 229 | Supply, installation, testing and comissioning of interconnecting copper refrigerant piping of DHE Grade C12200- ASTM B68, B75, chemical composition of copper %- 99.0 Min and Phosphorus %- 0.015 to 0.040 . For Annealed copper tube :- Tensile strength = 210 Mpa wih elongation % = 40 Min . Ink Mark Brand Printing on Hard Tubes should be present. duly insulated with tubular elastomeric nitrile rubber FM/UL approved with high water vapor diffusion resistance and low thermal conductivity should be certified 'Class O' in Fire Propagation as per BS 476 Part 6 including chase cutting andfilling with mortar, Slotted channel supports mounted on 10 mm threaded rod at suitable spacing the exposed piping shall be wrapped with glass woven cloth and lag coating for vapour barrier and weather protection. Joints shall be covered with nitrile rubber tape of 3 mm thick complete as required of following sizes. All as per pre approved by Engineer in charge. For additional technical parameters of products/ work , refer Annexure \\"A\\" attached with this BSR . |
| 230 | 15.9 mm O.D., wall thinkness ≥ 0.8mm (insulation – 13 mm thick) |
| 231 | 9.5 mm O.D., wall thinkness ≥ 0.8mm (insulation – 13 mm thick) |
| 232 | Providing & Fixing of modular type switch/ bell push duly ISI marked (IS :3854) with CM/L no. printed and made out of unbreakable and fire retardant vergin UV Stabilized Polycarbonate with brass terminals and captive screws & silver alloy contact tip with IP-20 rating ,minimum width of switch toggle( PUSH PART ) should not less then 20mm, including all as per pre approved by Engineer in charge,making connections, testing etc. as required. For additional technical parameters of product / work refer Annexure 'A' attached with this BSR |
| 233 | 25 Amp. 2 Module switch With Led Indicator |
| 234 | Providing & Fixing of modular type lockable feature socket duly made out of unbreakable and fire retardant vergin poly carbonate with brass terminals and captive screws & silver alloy contact tip with IP-20 rating , including all as per pre approved by Engineer in charge,making connections, testing etc. as required. For additional technical parameters of product / work refer Annexure 'A' attached with this BSR |
| 235 | 25 Amp. 2 Module Socket Please Enable Macros to View BoQ information |
AI Tender Summary
Tender Timeline
Jul 06, 2026
11:30 IST
Tender Published
Tender notice published.
CompletedJul 14, 2026
17:00 IST
Bid Submission Deadline
Online submission via eProcurement portal.
Upcoming · 3 daysJul 15, 2026
Bid Opening Date
Technical bids will be opened and evaluated.
Upcoming · 4 daysTender Documents
Download All (ZIP) ↓
Disclaimer
We takes all possible care for accurate & authentic tender information. However users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender