Tender For Repair And Replacement Of Plumbing Work, Sunken Repairs, Water Proofing, Plastering Repair To Window And Other Connected Items Of Certain Buildings Of Residential Area And Depot Area At installation Hamla Under Ge (Nw) Bhandup
Tender Value
44 Lakhs
Estimated cost
Bid Submission
27 Jul 2026
18 days left
EMD
88000
Bank guarantee accepted
Document Fee
500
Non-refundable
Tender Type
Online
Tender Overview
Organization
Tender ID
Competition Type
NCB
Bidding Type
Tender
Location / State
Mumbai Suburban → Maharashtra
EMD Exemption
Available
Quantity
Not Available
Website
Contact Person
Address
Project Description
Tender for Repair And Replacement Of Plumbing Work, Sunken Repairs, Water Proofing, Plastering Repair To Window And Other Connected Items Of Certain Buildings Of Residential Area And Depot Area At installation Hamla Under Ge (Nw) Bhandup
BOQ
| Sl. No. | Item Description |
| 1 | Demolition of cement concrete unreinforced of any description and in any position and removal of debris outside MD land complete all as specified and directed. |
| 2 | M & L for providing stages wise waterproofing treatment to sunken portion of toilets as under : Stage 1: Demolition of WC including lime concrete and cement concrete etc and preparing the surfaces of existing sunken portion of WCs or bath etc with wire brush to remove all loose dirt, oil grease etc including removing debries outside MD land etc complete all as specified and directed. Stage 2: Providing 15 mm thick plaster in CM (1:3) mixed with integral water proofing chemical of STP Ltd in the proportion /quantity all as per manufactures instructions. Stage 3: Primer - Mix Tarfelt LM with water in ratio 1:1 @ 250 gms/sqm and apply the primer on the plaster surfaces. Stage 4: Application of 1st coat of Tarfelt LM of STP Ltd without dilution with water@1kg / sqm by brush all as per manufactures instructions. Stage 5: Laying 50 GSM fyber glass cloth over the 1st coat while the coated surface is still tacky all as per manufacturers instructions. Stage 6: After 6 to 7 hours interval apply second coat i.e final coat of Tarfelt LM without dilution with water of STP Ltd by brush as per manufactures instructions @1kg / sqm. Stage 7: Providing 10mm thick protective plaster in CM (1:3) mixed with STP NO -1 @ 250ml / 50kg cement all as per manufactures instructions. |
| 3 | M & L for preparation of old decorated surfaces of walls by brooming down or steel wire brushing, scrapping down smoke soot, moulds, moss and efflorescent salts and treating oil and greasy spots and thereafter applying one coat of white wash complete all as specified and directed. |
| 4 | M & L for preparation of old decorated surfaces of ceiling by brooming down or steel wire brushing, scrapping down smoke soot, moulds, moss and efflorescent salts and treating oil and greasy spots and thereafter applying one coat of white wash complete all as specified and directed. |
| 5 | M & L for preparation of old decorated surfaces of walls by brooming down or steel wire brushing, scrapping down smoke soot, moulds, moss and efflorescent salts and treating oil and greasy spots and thereafter applying one coat of cement base paint complete all as specified and directed. |
| 6 | M & L for preparation of old surfaces of walls including washing, rubbing down and stopping of distempered and painted surfaces of wall and applying one coat oil bound distemper with roller complete all as specified and directed. |
| 7 | M & L for complete removal of existing treatment by scrapping / washing down with water and applying two coats of oil bound distemper over a coat of primer, applying with roller complete all as specified and directed. |
| 8 | M & L for white cement based wall care putty not less than 1 mm thick on wall / ceiling new or old surfaces of any description finished even and smooth complete all as specified and directed. |
| 9 | M & L for preparation of old decorated surfaces of walls any description not otherwise described over 10 cm width or girth and applying one coat of Plastic emulsion paint on wall and ceiling etc complete all as specified and directed. |
| 10 | M & L for preparation of old decorated wooden surfaces of any description not otherwise described over 10 cm width or girth and applying one coat of synthetic enamel paint complete all as specified and directed. |
| 11 | M & L for for preparation of old plastered surfaces of walls, chajjas, slab projections and applying one coats of 100% Anti fungal acrylic emulsion paint in approved shade including necessary scaffolding complete all as specified and as directed. |
| 12 | M & L for preparation of old decorated steel surfaces of any description not otherwise described over 10 cm width or girth and applying one coat of synthetic enamel paint complete all as specified and directed. |
| 13 | M & L for cutting out cracks (not exceeding 5 mm) to V-section in existing wall / chajjas and cleaning out and filling up with Dr fixit crack seal including necessary scaffoldings complete all as specified and as directed. |
| 14 | Taking down cement mortar or lime plaster of any description from stone or brick wall etc including raking out joints, hacking for key scrubbing down with water and disposing off the rubbish materials outside MD and including necessary scaffoldings complete all as specified and directed. |
| 15 | M & L for rendering 15 mm thick in CM (1:6) on fair faces of brick work or concrete surfaces of walls and finishing even and smooth without using extra cement complete all as specified and directed. |
| 16 | M & L for rendering 5 mm thick in (1:3) CM as in ceiling finishing even and smooth (without using extra cement) etc complete all as specified and directed. |
| 17 | M & L for rendering 15 mm thick in (1:4) CM [in two coats (10+5 mm)] with both coats mixed with liquid water proofing compound, surface finished even and fair without using extra cement complete all as specified and directed. Note:- WPC will be measured separately. |
| 18 | M & L for preparation of new plastered surfaces of walls, chajjas, slab projections and applying two coats of 100% Anti fungal acrylic emulsion paint in approved shade over a coat of primer and including necessary scaffolding complete all as specified and directed. |
| 19 | M & L for preparation of new plastered surfaces and applying three coats of white wash on wall complete all as specified and directed. |
| 20 | M & L for preparation of new plastered surfaces and applying three coats of white wash on ceiling etc complete all as specified and directed. |
| 21 | M & L for preparation of new plastered surfaces of walls and applying two coats of distemper oil emulsion over a coat of alkali resistant primer using roller etc complete all as specified and directed. |
| 22 | M & L for removal of plant growth by injection with chemical glyphospate solution (4% concentration) @ 20 ml or till refuse by cutting or injection in stem of plants or roots at 30mm. The area shall then be sprayed with solution 25 ml glyphosphate (4% concentration) dulited with 1 ltr of water. All roots / plants shall be removed completely and making good the distrubed surface and painted with cement base or acrylic paint all as directed by Engineer in charge. |
| 23 | Dismantling / Demolition of existing roof terracing of cement / brick concrete(unreinforced) and existing water proofing treatment of any thickness in any position on top of roof of building, cleaning surface of roof with brush / mechanical brush and with water throughly to romove all dust / dirt and loose particles to expose bare concrete roof slab and romoval of rubbish / demolished material outside MD land complete all as specified and directed. Note:- Demolition should be done by chiselling. |
| 24 | M & L for brushing neat cement slurry @ 3 Kgs of cement per sqm complete all as specified and directed. |
| 25 | M & L for rendering 15 mm thick in CM (1:3) on fair faces of brick work or concrete surfaces on roof finished even and smooth using liquid water proofing compound as per manufacturers instructions complete all as specified and directed. Note:- Supply only liquid water proofing compound shall be measured & paid separately. |
| 26 | M & L for PCC (1:2:4) type B0 (using 12.5 mm graded stone aggregate) as in levelling padding course over RCC roof surface including rounded or chamferred on edges etc mixed with approved water proofing compound all as per manufacturer's instructions on the roof surface to achieve requisite slope complete all as specified and directed. Note:- Supply only water proofing compound shall be measured & paid separately. |
| 27 | Supply only polymer based liquid water proofing compound complete all as specified and directed. |
| 28 | M & L for APP modified membrane roof treatment to the following specification:-(a) Applying oil bound bitumen primer @ 0.40 lit / Sqm of density 0.87 - 0.89 Kg / lit of 25 degree centigrate after preparation of the surfaces. (b) Supply and lay APP water proofing membrane reinforced with non woven polyster matt laid using butane torch by torch on application with a side lap of 10cm and 15cm end lap weighing not less than 3.6 kg/sqm. (c) Providing 20 mm thick screed in CM (1:4) with approved water proofing compound and mixture over a layer of non woven geotextile layer. (d) Providing 300 x 300 x 20 mm thick machine pressed Cement concrete tiles with minimum thickness of joint (not exceeding 3 mm) and are throughly filled with water proof polymer based joint morter complete all as specified and directed. Note:- The tiles shall be laid to the slop to avoid stagnation of water. |
| 29 | M & L APP modified membrane roof treatment to parapet wall surface to the following specification:-(a) Applying oil bound bitumen primer @ 0.40 lit / Sqm of density 0.87 - 0.89 Kg / lit of 25 degree centigrate after preparation of surface. (b) Supply and laying APP water proofing membrane reinforced with non woven polyster matt laid using butane torch by torch on application with a side lap of 10 cm and 15 cm end lap weighing not less than 3.6 kg/sqm.(c) Applying one coat of solar reflective bituminous paint all as per manufactures's instruction complete all as specified and directed. |
| 30 | Taking down eaves gutters and rainwater pipes (any size or pattern), including all fittings, heads, shoes, bends, swan-necks, etc., including cleaning or refixing or removal to store (measured overall as fixed along the centre line over fitting and accessories) complete all as specified and directed. |
| 31 | S & F 160 mm bore PVC (SWR) pipe single socketed(ISI Marked) any length with rubber ring joints, complete fittings etc fixed to walls complete all as specifed and directed. |
| 32 | S & F 110 mm bore PVC (SWR) pipe single socketed(ISI Marked) any length with rubber ring joints, complete fittings etc fixed to walls complete all as specifed and directed. |
| 33 | S & F 75 mm bore PVC soil waste pipe single socketed(ISI Marked) any length with rubber ring joints, complete fittings etc fixed to wall fixed with MS clamps 8mm dia with two nuts wall nails etc complete all as specifed and directed. |
| 34 | S & F 160 mm any radius dia PVC bend with or without access doors etc, complete all as specified and directed. |
| 35 | S & F 110 mm dia PVC bend any radius with or without access doors etc, complete as specified and directed. |
| 36 | S & F 110 mm bore PVC (SWR) Branch piece, single (single Y) equal or unequal of any radius with access door complete all as specified and directed. |
| 37 | S & F 75 mm bore PVC (SWR) Branch piece, single (single Y) equal or unequal of any radius with access door complete all as specified and directed. |
| 38 | S & F 110 mm bore PVC (SWR) Vent Cowl complete all as specified and directed. |
| 39 | Resecuring or easing & adjusting without taking down door shutter of any description exceeding 1.00 sqm but not exceeding 2.00 sqm each complete all as specified and directed. |
| 40 | Taking down door / window shutter of any description exceeding 1.00 sqm but not exceeding 2.00 sqm each and refixing in the same opening after easing, adjusting & renewal of unserviceable screws etc complete all as specified and directed. |
| 41 | Supply & fixing in repairs aluminium alloy wire cloth 0.45 mm nominal dia of wire and average width of aperture 1.40 mm and fixed with aluminium wire staples complete all as specified and directed. |
| 42 | M & L for cement concrete (1:5:10) Type E2 using 40 mm graded aggregate or brick bats as in lean concrete complete all as specified and directed. |
| 43 | S & F in repairs vitreous China squatting pan, 'orrisa' pattern WC of size 580 x 440 mm white with integral foot rest (excluding flushing cistern and flush pipe but including 'P' or 'S' trap and provision of lime concrete bedding complete all as specified and directed. |
| 44 | S & F in repairs Vitreous China wash down water closet Pan (Padestal Pattern) white with seat cover and fixing complete all as specified and directed. |
| 45 | S & F WC connector 110 mm PVC SWR for WC complete all as specified and directed. |
| 46 | S & F in repairs PVC valveless, syphonic action type, 10 ltrs cap flushing cistern, low level, white, with inlet, ball valve, float and handle including brackets and flush pipe 32 mm dia complete all as specified and directed. |
| 47 | S & F PVC connection 450 mm long complete all as specified and directed. |
| 48 | Dismantling floor, hearth or wall tiling any description and thickness including cement mortar bedding (but not backing) and removing rubbish off the premises complete all as specified and directed. |
| 49 | M & L for PCC 30mm thick (1:2:4) type B0, (12.5mm graded aggregate) in sub flooring complete all as specified and directed. |
| 50 | M & L for non-skid coloured joint free ceramic tiles 7 to 8 mm thick area of each tile exceeding 0.11 Sqm but not exceeding 0.18 sqm, in floors etc set and jointed in neat cement slurry over and including provision of bedding layer 15 mm thick in CM (1:4) complete all as specified and directed. |
| 51 | M & L for glazed ceramic jointless coloured tiles in vertical surface 350 x 250 x 7 mm / 450 x 350 x 7 mm set and jointed in neat cement slurry over and including provision of bedding layer 10 mm thick in CM (1:3) complete all as specified and directed. |
| 52 | M & L for non-skid coloured joint free ceramic tiles 7 to 8 mm thick area of each tile exceeding 0.18 sqm but not exceeding 0.38 sqm, in floors etc set and jointed in neat cement slurry over and including provision of bedding layer 15 mm thick in CM (1:4) complete all as specified and directed. |
| 53 | M & L for non-skid coloured joint free ceramic tiles 7 to 8 mm thick area of each tile exceeding 0.18 sqm but not exceeding 0.38 sqm, in skirting etc set and jointed in neat cement slurry over and including 10 mm thick rendering in CM (1:4) complete all as specified and directed. |
| 54 | S & F in repair PVC cabinet mirror of size 600 x 450 mm complete all as specfied and directed. |
| 55 | Demolition of cement concrete in ground floor / paving not exceeding 15cm thick below or above GL unreinforced complete all as specified and directed. |
| 56 | M & L for cement concrete (1:3:6) type C-1, (20 mm graded aggregate) 75 mm thick as in plinth protection finished even and smooth without using extra cement complete all as specified and directed. |
| 57 | S & F in repair Mirror 600 mm x 450 mm bevelled edge mirror of selected quality glass, mounted on 6 mm thick AC building board or commercial plywood and fixed to wooden plughs with chromium plated brass screws and cup washers complete all as specified and directed. |
| 58 | Demolition of reincorced concrete in chajjas and similar suspended, slab facia drop etc work complete all as specified and directed. |
| 59 | M & L for RCC (1:1.5:3) type A1 (using 20 mm graded stone aggregate) in chajjas complete all as specified and directed. |
| 60 | M & L for RCC (1:1.5:3) type A1 (using 20 mm graded stone aggregate) in fascias, louvres, parapets and the like complete all as specified and directed. |
| 61 | S & F TMT bars 10 mm dia & over, cut to length, bent to shape required including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9 mm dia or securing with clips complete all as specified and directed. |
| 62 | M & L for form work for soffit and sides of chajjas, troughs and similar items including edges rough finished surface of concrete flat complete all as specified and directed. |
| 63 | M & L for form work to fins, louvers, fascia rough finished surface of concrete flat complete all as specified and directed. |
| 64 | Dismantling wall and ceiling boards (fibre, pulp, insulation etc) or insulation boards / slabs / blankets any thickness including cover fillets complete all as specified and directed. |
| 65 | M & L for Hangers 6 mm dia GI (upto 1200 mm length) adjusting level fixed to roof slabs by means of ceiling cleats made out of GI flat 40 x 3 mm size 60 mm long and expansion hold fasterners 12.5 mm dia 40 mm long complete all as specified and directed. |
| 66 | M & L for anodised aluminium snap grid frame work for false ceiling of grid size 605 x 605 mm complete all as specified and directed. |
| 67 | M & L for Non asbestos fibre cement building boards 4 mm thick fixed / inserted to GI frame work complete all as specified and directed. |
| 68 | Supply and fixing hot dipped GI imposed grid with 24 mm wide T section exposed flanges powder coated frame work comprising of main runner made runner made from 0.33mm thick GS Sheet of size 24 mm x 32 mm x 300 mm @1200 mm C/C GI wire 4mm dia fixed by rawl plug, level adjusters and screws etc flush fitting of 1200 mm long cross tee interlocked between main runners @ 600mm c/c to form 1200 mm x 600 mm modules cross tee longer than 600mm to be supported independently 600 mm x 600 mm modules shall be formed by fitting 600mm long cross tee centrally between 1200 mm cross tee, perimeter wall angle shall be GS of size 19mm x 19mm and 0.45 mm thick 300 mm long including 600 mm x 600m m x 8 to 10 mm thick Armstrong gypsum reinforced board with painting with two coat of plastic emulsion paint over primer complete all as specified and directed. |
| 69 | S & F in repairs Rotational moulded polyethylene water storage tanks (Cylindrical verticval with closed top) hoisted & fixed in position of 500 ltrs capacity complete all as specified and directed. |
| 70 | S & F in repairs Rotational moulded polyethylene water storage tanks (Cylindrical verticval with closed top) hoisted & fixed in position of 1000 ltrs capacity complete all as specified and directed. |
| 71 | S & F in repairs Rotational moulded polyethylene water storage tanks (Cylindrical verticval with closed top) hoisted & fixed in position of 2000 ltrs capacity complete all as specified and directed. |
| 72 | Cleaning of PVC water tanks at any height (on accessible / inaccessible roofs) by removing all scale, dirt, mud any foreign material and removing and removing accummulated silt, other dirty substance, algae, fungus and other bacterial material from sides / bottom of tank cleaning shall be done by draining / pumping out water / sludges from bottom from wall / floor / roof by high pressure clleaning method with jet set and again cleaning the tank with fresh water. Disinfecting by using UV radiator and approved chemical (Chloriten) after cleaning writing following letter figures on black background with white enamel paint of capacity exceeding 300 ltrs but not exceeding 500 ltrs :- (i) Date of cleaning(ii) Next date of cleaning.(iii) Remove of the existing lettering / figures completely. |
| 73 | All as per item no. 72 above but tank of capacity exceeding 501 ltrs but not exceeding 1000 ltrs |
| 74 | All as per item no. 72 above but tank of capacity exceeding 1001 ltrs but not exceeding 2000 ltrs |
| 75 | All as per item no. 72 above but tank of capacity exceeding 2001 ltrs but not exceeding 5000 ltrs |
| 76 | S & F in repairs 25 mm dia ball valve high pressure of PTMT with epoxy coated Aluminium rod & high density plastic ball screwed for iron pipe and fixed complete all as specified and directed. |
| 77 | S & F Nipple suitable for HDPE water tank (minimum weight 25mm - 65 gms) 25mm bore dia complete all as specified and directed |
| 78 | S & F in repairs steel rolling shutters 1.25 mm thick lath, without ball bearing, as specified including top cover, anchoring rod, hasp and staple and one shop coat of primer, erected in position as indicated complete gear operated type with bevel gear box and crank handle complete all as specified and directed. |
| 79 | S & F Safety lever locks mild steel with 4 levers for rolling shutters complete all as specified and directed. |
| 80 | S & F Ball bearing for rolling shutters complete all as specified and directed. |
| 81 | Dismantling of Plain or corrugated steel sheeting, any gauge, thickness, including Nainital or similar pattern roof coverings complete all as specified and directed. |
| 82 | Dismantling of wrought iron or mild steel work in any description and in any position complete all as specified and directed. |
| 83 | M & L for rolled sections as in framing for cladding, glazing and the like fixed with angle cleats and connecting plates etc conforming to Fe 410-W (Gde-E-250) complete all as specified and directed. |
| 84 | M & L for roof trusses (framed) trussed, purlins, crange gantries, rails and fastenings and heavy bracket framing (beam, tee, angle, channel or flat sections) including distance pieces, cleats etc conforming to Fe 410-W (Gde-E-250) complete all as specified and directed. |
| 85 | S & F Pre-painted galvalume aluminium zinc (150micron) coating GI based corrugated steel sheet 0.50 mm thick of an colour having tensile strength of 550 Mpa as in roof covering / cladding to wall, fixed with self tapping screws complete all as specified and directed. |
| 86 | S & F Pre-painted galvalume aluminium zinc(150 micron) coating GI based Plain steel sheet 0.50 mm thick of an colour having tensile strength of 550 Mpa as in roof covering / cladding to wall, fixed with self tapping screws complete all as specified and directed. |
| 87 | M & L for prepration of new steel surface of any description not exceeding 60 cm in girth and applying two coats of synthetic enamel paint over a coat of rex oxide primer complete all as specified and directed. |
| 88 | M & L for post construction, antitermite treatment of soil under existing floors using emulsion @ one litre per hole, 300 mm apart including drilling and plugging 12mm dia holes with cement mortar 1:2 (1 cement: 2 coarse sand) to match the existing floors complete all as specified and directed. |
| 89 | M & L for providing and injecting chemical chloropyrphos emulsion conforming to IS-3244 (with 20% EC) for post construction antitermite treatment along external wall below concrete or masonry apron @ 2.25 litre per running meter including drilling and plugging note complete all as specified and directed. |
| 90 | M & L for post construction antitermite treatment at point of contact of wood work by chemical emulsion (in oil or kerosene based solution) @ 0.5 ltr/hole by drilling 6mm dia hole at a downward angle of 45 degree at 150 mm centre to centre and sealing the same complete all as specified and directed. |
| 91 | M & L for two coat of aluminium paint over a coat of alumimium red oxide primer to new steel surface including preparation complete all as specified and directed. |
| 92 | Resecuring or easing, greasing & adjusting without taking down door shutter or rolling shutter of any description exceeding 2.00 sqm each including replacement of unserviceable lever, lock, handle, covering etc as required for smooth operation complete all as specified and directed. |
| 93 | S & F in repair 25 mm fancy type decorative stainless steel double curtain road with double bracket suitable hanging multiple sets curtains together for window and doorincluding 02 nose double bracket and 04 nose fancy type rod for each window complete all as specified and directed. |
| 94 | S & F in repairs tubular towel rail, 20 mm dia, D type, 60cm long between flanges of brass chromium plated complete all as specified and directed. |
| 95 | Taking up or down steel tubing 15 mm bore of pipe and connections including cleaning for refixing etc as required complete all as specified and directed. |
| 96 | All as per item no. 95 above but 20 mm bore of pipe complete all as specified and directed. |
| 97 | M & L for tubes medium grade galvanised, with all fittings and fixed complete to walls or ceiling or laid in floors 15 mm bore dia complete all as specified and directed. |
| 98 | All as per item no. 97 above but 20 mm bore dia complete all as specified and directed. |
| 99 | S & F in repair Wash basin, Vitreous China white (Flat back) 630 x 450 mm including brackets, pinning in ends of brackets or erecting stand including fixing of waste pipe and pillar type etc complete all as specified and directed.Note: Suppy of pillar tap and waste pipe shall be measured and paid seperately. |
| 100 | S & F in repairs 15 mm pillar tap cast copper alloy chromium plated fancy type complete all as specified and directed. |
| 101 | S & F in reapairs stop valves 15 mm bore dia, cast copper alloy fancy type, chromium plated with long shank and cup concealed type, screwed down high pressure, with crutch or butterfly handle, screwed both ends for iron pipe or for unions complete all as specified and directed. |
| 102 | All as per item No. 101 above but angle cock Chromium plated 15 mm bore dia complete all as specified and directed. |
| 103 | S & F in repairs health faucet (Hand wash for EWC) first quality including CP bracket to hold the faucet with CP pipe of suitable length in wall complete all as specified and directed. |
| 104 | S & F in repairs Glass Assembly sheet glass consisting of 5.5 mm thick sheet glass 12 cm wide with chromium plated bracked guard and railing 60 cm long complete all as specified and directed. |
| 105 | S & F in repairs bib tap brass 15 mm bore dia chromium plated long shank fancy type with curtch or butterfly handle, screwed down, screwed for iron pipes complete complete all as specified and directed. |
| 106 | S & F in repairs sink with drainage board made of stainless steel 1mm thick kitchen with plugs, washers and wasters, including bedding in cement mortar to dwarf wall or including fixing cantilever brackets and connecting union to pipe overall size 915 mm x 460mm bowl size 410 mm x 330 mm x 160 mm and fixed complete all as specified and directed. |
| 107 | S & F in repairs stainless steel floor trap, plain with grating removeable & refixable type including jointing with solvent cement 75 mm dia of outlet complete all as specified and directed. |
| 108 | S & F in repairs stainless steel floor trap, plain with grating removeable & refixable type including jointing with solvent cement 100 mm diameter of outlet complete all as specified and directed. |
| 109 | Demolition of brick work built in CM including taking out roots vegetation if any at any position and removal to outside MD land complete all as specified and directed. |
| 110 | M & L for brick work with sub class 'B' bricks straight or curved on plan exceeding 6m mean radius built in CM (1:6) complete all as specified and directed. Please Enable Macros to View BoQ information |
AI Tender Summary
Tender Timeline
Jul 06, 2026
11:30 IST
Tender Published
Tender notice published.
CompletedJul 27, 2026
17:00 IST
Bid Submission Deadline
Online submission via eProcurement portal.
Upcoming · 18 daysJul 28, 2026
Bid Opening Date
Technical bids will be opened and evaluated.
Upcoming · 19 daysTender Documents
Download All (ZIP) ↓
Disclaimer
We takes all possible care for accurate & authentic tender information. However users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender