Tender For special Repair To Certain Buildings At Drugmulla And Provn Of Garbage Pit At Pohrupet Under The Aor Of Ge 874 Ews.
Tender Value
Ref. Documents
Estimated cost
Bid Submission
27 Jul 2026
15 days left
EMD
98800
Bank guarantee accepted
Document Fee
500
Non-refundable
Tender Type
Online
Tender Overview
Organization
Tender ID
Competition Type
NCB
Bidding Type
Tender
Location / State
Kupwara → Jammu and Kashmir
EMD Exemption
Available
Quantity
Not Available
Website
Contact Person
Address
Project Description
Tender for special Repair To Certain Buildings At Drugmulla And Provn Of Garbage Pit At Pohrupet Under The Aor Of Ge 874 Ews.
BOQ
| Sl. No. | Item Description |
| 1 | S & F for Pre- painted galvalume aluminium zinc coating GI based corrugated steel sheet 0.50mm thick of an colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws complete all as specified and directed. |
| 2 | S & F for Pre-painted galvalume aluminium zinc coating GI based Plain steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws as specified. |
| 3 | S&F Weather boarding, clean sawn, plain, 20mm thick or feather edged 15 mm to 20mm thick and fixed with 30mm lap. Dismantling boarding, any description, fixed in any position with Screws complete all as specified and directed. |
| 4 | M & L for 25mm thick 2nd class softwood boarding, planed one side, with butt joint fixed with nails in Fascia, eaves boarding complete all as specified. Dismantling boarding, any description, fixed in any position with Screws complete all as specified and directed. |
| 5 | S&F galvanised mild steel wire cloth 0.56 mm nominal dia of wire and average width of aperture 1.18 mm and fixed with tinned tacks, or galvanised wire staples to wooden/steel frames with beading complete all as specified and directed. |
| 6 | S&F in repair galvanised mild steel wire cloth 0.56 mm nominal dia of wire and average width of aperture 1.18 mm and fixed with tinned tacks, or galvanised wire staples to wooden/steel frames with beading complete all as specified & directed. |
| 7 | M&L for preparation of New surfaces and applying two coat of synthetic enamel paint Over a One Coat Of Pink Primer wooden surfaces of any description not other wise described over 10 cm width or grith etc complete all as specified and directed. |
| 8 | M & L for second class soft wood in scantling clean swan including dismantling timber scantling 40 Sq cm and over in section in any position in unframed work complete all as specified and directed. |
| 9 | Taking down chowkat with shutters exc.1.5 Sqm but n exc.4 Sqm (w/o taking off shutters from chowkhat) complete all as specified and directed. |
| 10 | Taking down chowkat with shutters n. exc.1.5Sqm (w/o taking off shutters from chowkhat) complete all as specified and directed. |
| 11 | S & F 2nd class soft wood plain solid straight chowkats and frames wrought framed, rebated on the solid complete all as specified and directed. |
| 12 | S & F plain framed, panelled shutters 35 mm thick 2nd class softwood, (any numbers of panels), with panels of timber flats on both sides of veneered particle board med density, wood particle board with commercial face fitted to chowkhat complete all as specified and directed. |
| 13 | M&L for factory made 35mm Glazed and skeleton shutters, second Class Soft wood for open rebated and prepared to receive glass, gauze, etc. (without sash bars), edges of framing plain, chamfered or rounded. fitted with cut and mitred beads, etc.; sizes of members of shutters as specified in SSR Part I, Section 8, clause 8.24 (a); supplied and fitted to chowkats complete all as specified and directed. |
| 14 | S & F glazed & skeleton shutters 30 mm thick 2nd class softwood, open rebated and prepared to receive glass, gauze, etc.(without sash bars), edges of framing plain, chamfered or rounded, fitted with cut & mitred beads for securing glass etc. sizes of members of shutters as specified in SSR Part I Section 8 clause 8.20 (a) fitted to chowkhats but divided into squares, with plain, chamfered or rounded, mitred and rebated sash bars, any numbers complete all as specified and directed. |
| 15 | M&L plywood grade BWR type BB, 9 mm thick fixed with nails to timber frame work in ceiling. Dismantling wall and ceiling board (fiber, pulp, insulation, etc.) or insulation board /slab/blankets, any thickness, including cover fillets complete all as specified and directed. |
| 16 | M & L for Plain fillets of exc. 3 & n exc. 6 Sqcm, square rectangular or triangular in section, clean swan, secured nails complete all as specified and directed. |
| 17 | S&F in repair for 03 mm thick Sheet glass, ordinary quality and glazing with oil putty in square n exc 0.5 sq.m in each pane complete all as specified. Including hacking out old broken glass (any thickness, size quality of description) from wooden frames or stone, concrete or brick surrounds, glazed with putty or fixed with beads complete all as specified and directed. |
| 18 | S&F for MS barrel tower bolt, stove enamelled black, with bright bolt of 100mm long complete all as specified and directed. |
| 19 | All as per item No 18 above but 150mm long.. |
| 20 | S&F for MS Sliding door bolt, plate type, stove enamelled black, with bright bolt not less than 12mm dia of 250mm long complete all as specified and directed. |
| 21 | S&F for MS butt hinges med. Weight, cold rolled 100mm long complete all as specified and directed. |
| 22 | All as pe item no 21 but 75mm long. |
| 23 | M & L for mild steel pressed handles, oval type, stove enamelled black of 100mm long complete all as specified and directed. |
| 24 | All as per item no 23 above but 150 mm long. |
| 25 | M & L for 75mm thick plain cement concrete 1:4;8 type D-2 (using 40mm graded crushed stone aggregate) as in sub base or floor complete all as directed |
| 26 | M & L for 25 mm thick plain cement concrete 1:2:4 type Bo (using 12.50 mm graded crushed stone aggregate) as in sub base or floor complete all as specified and directed. |
| 27 | M&L for machine cut Kota stone slab flooring 18 to 20mm thick as in floor, cooking platform, treads etc. laid over 20 mm screed bed or bedding layer in CM 1:6 set and jointed in neat cement slurry and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing by machine, complete all as specified and directed. |
| 28 | M&L for machine cut Kota stone 15-16 mm thick as in riser of steps, skirting, dado and pillar set over 10 mm rendering in CM 1:3 and jointed with grey cement slurry mixed with pigments to match the shade including rubbing and polishing complete all as specified and directed. |
| 29 | M&L for Glazed coloured ceramic tiles in vertical surface 300x450x7/ 600x300x7 mm thick over and including 10 mm rendering in CM 1:4 set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tile including dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish off the premises complete all as specified and directed. |
| 30 | M&L for 16-18 mm thick Granite (of any type) work (table rubbed and polished) in steps, jambs, pillars, window- cills, cooking platforms and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite laid over and including 15 mm screed bed or bedding layer in CM 1:4 complete all as specified and directed. |
| 31 | Demolition of cement concrete (un-reinforced) in ground floors and pavings n exc. 15cm thick. (below or above ground level) complete all as specified and directed. |
| 32 | M & L PCC 1:3:6 type C2 (using 40mm graded stone aggregate) 75mm thick as in plinth protection and to be finished smooth and even without using extra cement etc complete all as specified and directed |
| 33 | M & L Brickwork with subclass ‘B’ bricks, straight or curved on plan exc 6m mean radius built in CM (1:6) complete all as specified and directed. |
| 34 | M&L for random rubble masonry using sand stone uncoursed well bonded bedded and solidly hearted built in CM 1:4including Demolition of brick/stone masonry, built in cement mortar including all quoins, arches, pillars etc but excluding ashlar facing, dressed stonework and precast concrete articles including demolition of Brickwork or stone/ boulder masonry, built in cement mortar including all quoins, arches, pillars, etc, but excluding ashlar facings, dressed stonework and precast concrete articles complete all as specified and directed. |
| 35 | M & L for 10 mm thick rendering in Cement Mortar 1:4 on any faces of brick or concrete surfaces of walls & finishing the surface even and smooth without using extra cement complete all as Specified and directed. |
| 36 | M & L for 10 mm thick rendering in Cement Mortar 1:4 on any faces of brick or concrete surfaces of walls & finishing the surface even and smooth without using extra cement including taking down cement or cement lime plaster on brick or stone walls, any description, including raking out joints, hacking for key, scrubbing down with water, etc. complete all as specified and directed. |
| 37 | M & L for 15mm thick rendering in Cement Mortar 1:6 on any faces of brick or concrete surfaces of walls & finishing the surface even and smooth without using extra cement including taking down cement or cement lime plaster on brick or stone walls, any description, including raking out joints, hacking for key, scrubbing down with water, etc. complete all as specified and directed. |
| 38 | M & L for Extra over stone walling for hammer dressing to face stones and dressing of face beds and joints, as specified, of random rubble walling, uncoursed or brought upto courses maximum depression on face of straight edge 40mm complete all as specified and directed. |
| 39 | M & L for raised pointing to random rubble or polygonal rubble uncoursed or brought upto course set in cement mortar (1:3) complete all as specified and directed. |
| 40 | M&L for preparation of new plastered surfaces of wall and applying two coat of oil bound distemper complete all as specified and directed. |
| 41 | M & L for applying two coats of cement base paint over a coat of new plastered surfaces of wall complete all as specified and directed. |
| 42 | M&L providing and applying cement base putty of 1 mm thickness over New plastered surface to prepare the surface even and smooth. complete all as specified and directed |
| 43 | M & L for hardcore of gauge n exc. 63 mm, deposited, spread and levelled in layers n exc. 15 cm thick, watered and rammed to a true surface complete all as specified and directed. |
| 44 | S&F in repair for Stop valves cast copper alloy, fancy type, chromium plated, screwed down, high pressure with crutch or butterfly handle, screwed both ends for iron pipe or for unions of 15mm bore pipe complete all as specified and directed. |
| 45 | S&F in repair for fancy type bib taps cast copper alloy, chromium plated, with crutch or butterfly handle screwed down screwed for iron pipe or brass ferrule of 15mm bore complete all as specified and directed. |
| 46 | S&F in repairs pillar tap cast copper alloy, fancy type with capstan heads chromium plated screwed down with high pressure with or without lettered hot or cold with long screwed, shanks and fly nuts screwed for iron pipe 15mm dia complete all as specified and as directed. |
| 47 | S&F 1000 Ltr capacity PVC water storage tank (cylindrical vertical with closed top) and fixed in position all as specified in SSR Part -I, including dismantling of old tank complete all as specified and directed. |
| 48 | S&F GI tube 15 mm dia medium grade galvanised with all fittings laid in floors /wall etc. complete all as specified and as directed. |
| 49 | S&F GI tube 20 mm dia medium grade galvanised with all fittings laid in floors /wall etc. including taking up or down 20mm dia GI steel tubing and connections, including cleaning for refixing or removal to store complete all as specified and as directed. |
| 50 | M & L for lagging to 20 mm bore pipes used in internal water supply or plumbing all round with, 25mm thick bonded mineral wool preformed 'SNAPON' pipe section of density 144 Kg \cum conforming to IS 9842 along with chicken mesh wire netting 25 gauge , 20 mm mesh complete all as specified and directed. |
| 51 | S&F 110mm dia PVC (SWR) pipes single socketed, in any length with rubber ring joints, laid in trenches or in floors / fixed to walls. |
| 52 | S&F PVC (SWR) bends any radius, 110mm bore, fitted with oval access door complete all as specified and directed. |
| 53 | S & F Grating doom 125 mm dia with waste hole of PTMT. (Minimum weight 40gms) complete all as specified and directed. |
| 54 | S&F in repairs two way angular stop cock chromium plated 15mm dia complete all as specified and directed. |
| 55 | S&F ball valves, high pressure, with polythene float and flynut complete,20mm bore, complete all as specified and directed. |
| 56 | S&F for 20mm bore gun metal globe or gate valve with iron wheel head, screwed both ends complete all as specified and directed. |
| 57 | S&F sinks with drainage board made of stainless steel 1 mm thick kitchen or laboratory with plugs, washers and wastes, including bedding in cement mortar to dwarf wall or including fixing cantilever brackets and connecting union to pipe over all size 915mmx460mm bowl Size 10mmx330mmx 160mm complete all as specified and directed. |
| 58 | M&L Veneered decorative plywood, 12 mm thick grade 1 (with BWR resin) with decorative face veneers on one faces; fixed with nails to timber frame work as in walls complete. Dismantling wall and ceiling board (fibre, pulp, insulation, etc.) or insulation board /slab/blankets, any thickness, including cover fillets complete all as specified and directed. |
| 59 | Dismantling wrought iron or mild steel work of any description not otherwise provided for complete all as specified and directed. |
| 60 | M&L for mild steel work as in posts and struts in fencing including cutting tops to shape as directed, drilling holes, notching for wire, etc.; flat iron fillets (for securing wire mesh etc.) including all necessary drilling, bolting or riveting, etc., and similar work conforming to Fe-290 Gde E-165 complete all as specified and directed. |
| 61 | Demolition of tone slabs and tiles of any laid bedded and pointed in any mortar description or thickness in floors, walls aprons etc. |
| 62 | M&L for Preparation of old painted surfaces and applying two coat of synthetic enamel paint on wooden surfaces of any description not other wise described over 10 cm width or grith etc complete all as specified and as directed. |
| 63 | M&L for preparation of New steel surfaces over 10 cm in width or girth and applying two coats of synthetic enamel paint on new surfaces, Over a one coat of red oxide primer complete all as specified and directed. |
| 64 | M&L for Machine pressed precast concrete interlocking paver block any shape and size confirming to IS 15658-2006 of 60 mm thickness, M-35 Grade with grey cement and pigment complete all as specified and directed. |
| 65 | M&L for Sand filling under floors or in foundations including watering and consolidation complete all as specified. |
| 66 | M & L for PCC 1:3:6 type C1 (using 20 mm graded crushed stone aggregate), in lintels upto 1.5m clear span, cills, steps; seismic and other similar bands, plinth courses, string courses, lacing courses, parapets and railings upto 60 cm in height, copings, kneelers, apex stones, bed plates, kerbs not provided for, water troughs and the like including weathering, slightly rounded or chamfered angles and throating, complete all as specified and directed. |
| 67 | M&L for cement concrete in foundations, filling and mass concrete type D2, 1:4:8 (40mm graded aggregates) complete all as specified and directed. |
| 68 | M&L RCC work M-25 design mix (using 20mm graded crushed stone aggregate) as in slab supported in walls cantilevers etc complete all as specified and directed. |
| 69 | M & L for MS TMT bars Mild steel bars 10mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and directed. |
| 70 | S&F for Butchering meat hooks made of SS- 304 grade of S - Shape or T - shape design , with length ranging from 8 to 10 inches & thickness of 5 to 10 mm in which one end is widely sharp for easy insertion into meat ,the other end is rounded or blunt safe handling or hanging in tubular 50 mm dia pipe high grade of length as required at site complete all as specified direction . |
| 71 | M&L plywood grade BWR type BB, 6 mm thick fixed with nails to timber frame work in ceiling including dismantling wall and ceiling board (fibre, pulp, insulation, etc.) or insulation board /slab/blankets, any thickness, including cover fillets complete all as specified and directed. |
| 72 | M&L plywood grade BWR type BB, 9 mm thick fixed with nails to timber frame work in Wall including dismantling wall and ceiling board (fibre, pulp, insulation, etc.) or insulation board /slab/blankets, any thickness, including cover fillets complete all as specified and directed. |
| 73 | Dismantling wall and ceiling board (fibre, pulp, insulation, etc.) or insulation board /slab/blankets, any thickness, including cover fillets complete all as specified and directed. |
| 74 | M&L for 10 to 12 mm thick 2nd class soft wood wall panelling of good quality wood planed one side and edges tonged and grooved or rebated other side and dovetailed joints, chamfered both sides fixed to frame work with secret nailed as in wall panelling 15mm including cornice and beading as required and applying two coats of varnish over a filler coat of thin varnish after preparation of surface, complete all as specified and directed. Note : Frame work shall be measured and paid separately. |
| 75 | M&L non skid ceramic tiles 7 to 8 mm thick area of each tiles exc 0.18 sqm but not exc 0.38 sqm, laid in floors etc., set and jointed in neat cement slurry and pointed in white cement to match the shade of tile laid over and including 15mm thick bedding layer in cement mortar (1:6) including necessary cutting and waste as per site requirement including dismantling floor, hearth or wall tilling including cement mortar bedding, removing serviceable tile to rubbish of the premises complete all as specified and directed. |
| 76 | S&F 500 Ltr capacity PVC water storage tank (cylindrical vertical with closed top ) and fixed in position all as specified in SSR Part -I, including dismantling of old unserviceable tank any capacity and any type complete all as specified and directed. |
| 77 | M&L for 50 mm thick PCC 1:2:4type B-0 (using 12.50 mm graded aggregate) for floor complete all as specified and directed. |
| 78 | S&F in repair door closer hydraulically regulated Aluminium (extruded section body) designation No 3 universal type, suitable for door shutters of 851 to 1000 mm in width and of weight between 61 to 80 Kg and fixed complete all as specified and directed. |
| 79 | S&F For Glass dividing strips, 3 mm thick, 38 mm thick complete all as specified and directed. |
| 80 | Surface excavation n. exc 30cm deep and averaging 15cm deep and getting out any type of soil complete all as specified and directed. |
| 81 | Excavation in trenches n.exc 1.50m wide and n. exc 1.50m in depth and getting out any type of soil complete all as specified and directed. |
| 82 | M&L for Brick work with sub class 'B' bricks, straight or curved on plan exceeding 6 mtr mean radius, built in cement mortar 1:4 complete all as specified and directed. |
| 83 | M&L for PCC M-30 Design mix (using 20 mm graded crushed stone aggregate) as in coping including necessary formwork, weathering, slightly rounded or chamfered angles complete all as specified and directed. |
| 84 | M&L for 15 mm thick cement plaster in cement mortar 1:4 on fair faces of bricks or concrete surface and finished even and smooth without using cement, complete all as specified and directed. |
| 85 | M&L for non skid ceramic tiles (coloured) 7 to 8 mm thick (square/ rectangular) area of each tile exceeding 0.06 sqm but not exceeding 0.11 sqm, in floors etc. laid over and including 15 mm screed bed or bedding layer in CM 1:6 set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tile Complete all as specified and directed. |
| 86 | M&L for Glazed coloured ceramic tiles in vertical surface 300x450x7/ 600x300x7 mm thick over and including 10 mm rendering in CM 1:4 set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tile complete all as specified and directed. |
| 87 | Material and labour for PCC 1:4:8 type D2 in 100 mm sub base of floor complete all as specified and directed. |
| 88 | Material and labour for PCC 1:2:4 type B1 40mm thick levelling in floor complete all as specified and directed. |
| 89 | S&F mild steel framework for such as grills gratings etc with end of bars shouldered an or riveted or forced into spikes framed guard bars and similar work confirming to Fe-410-0 or Fe-310-0 complete all as specified and directed. |
| 90 | M & L for mild steel framed work as in doors or gates of angle or other section with gusset plates, rails, braces etc completed drilled for fixing of steel sheeting or other covering, door etc to be prepared for hanging or sliding with and including either hooks and hinges orr steel hanging door fittings (exclusive of steel sheeting or other covering, running rails and guides) and hanging, also fastening and fixing complete all as specified and as directed. |
| 91 | Wire netting of 25mm size galvanised steel wire 1.40mm dia fixed with tinned tacks of wire staples complete all as specified and directed. |
| 92 | M&L for RCC design Mix M-25 Beams, cantilevers, bressummers, lintels over 1.5m span complete all as specified and directed. |
| 93 | M&L for mild steel TMT Bars 6mm to 8mm dia cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and directed. |
| 94 | Returning, filling in including spreading, levelling, watering and well ramming in layers not exc 25cm thick complete all as specified and directed. |
| 95 | Removing excavated material n exc 50m and depositing where directed at a level n exc 1.5m above the starting point complete all as specified and directed. |
| 96 | M&L for 20 cm x 20cm x 25 mm thick Chequered cement concrete tiles (in any colour & shape), set, jointed and pointed in neat cement slurry in floors with grey cement & no pigment over 20 mm screed bed in CM 1:6 complete all as specified and directed. |
| 97 | S&F in 15 mm bore fancy type long body bib tap, half turn, with wall flange, cast copper alloy with capstan heads, chromium plated, screwed for iron pipe or for brass ferrule, complete all as specified & as directed. |
| 98 | Earth work in excavation by mechanical means (Hydraulic excavator) means over areas (exceeding 30 cm in depth, 1.5 m in width as well as 10 sqm on plan) including getting out and disposal of excavated earth lead upto 50 m and lift upto 1.5m, complete all as specified and directed. |
| 99 | M & L PCC 1:3:6 type C - 2 in foundation, filling and mass concrete (using 40 mm graded crushed stone aggregate) complete all as specified and directed. |
| 100 | M & L for rendering 15 mm thick in CM 1:4 on stone masonary surfaces or surfaces of fair faces of brickwork and finishing even & smooth without using extra cement complete all as specified and directed. |
| 101 | Extra for forming fair finished drain or channel 30cm inner girth in cement concrete using extra cement including forms moulds, mitred /stopped ends etc complete all as specified and directed. |
| 102 | M & L Pre -Cast RCC 1:2:4 Type B1 (20 mm graded stone aggregate) nominal mixed cast in situ Providing precast cement concrete in in landings, cover slabs (for man holes etc.) chullah hoods, chajjas, water troughs, mangers, shelves and similar articles with plain faces complete all as specified and directed. |
| 103 | Dismantling plain or corrugated steel sheeting, any gauge, thickness including Nainital or similar pattern roof covering complete all as specified and directed. |
| 104 | Demolition of Brickwork or stone/ boulder masonry, built in cement mortar including all quoins, arches, pillars, etc, but excluding ashlar facings, dressed stonework and precast concrete articles complete all as specified and directed. |
| 105 | Taking up or down 15mm dia GI steel tubing and connections, including cleaning for refixing or removal to store complete all as specified and as directed |
| 106 | Dismantling of rain water pipe and sewage line pipe of any type and any size including fitting complete all as specified and as directed. |
| 107 | M & L for point wiring for one light point/fan point controlled by one switch with 1.5 sqmm PVC FRLSH insulated un-sheathed copper conductor single core multi strand flexible cable and 1.5 sqmm PVC FRLSH insulated un-sheathed copper conductor single core multi stranded flexible cable (green colour) as earth lead in and including cable 1100 volts grade including casing and capping/conduit (ISI marked) including sunk cast iron/pressed steel terminal boxes, junction boxes, other boxes made from thick sheet of suitable sizes for mounting of switches, sockets, fan regulators, light fittings etc. covered with plastic laminated sheet or PVC gang box 2 to 8 way as per site requirement fitting in surface mount or concealed including cutting chases to wall making good the disturbed surfaces to match with the existing specification including taking down old one complete all as specified and directed. |
| 108 | All as per item No 107 herein before but wiring with 1.5 sqmm copper wire ( FRLSH) and 1.5 sqmm earth wire for socket outlet 3 pin 5 amps on same board, all as specified and directed by Engr-in-Charge. |
| 109 | All as per item No 107 herein before but wiring with 1.5 sqmm copper wire (FRLSH) and 1.5 sqmm earth wire for socket outlet 3 pin 5 amps on independent board. |
| 110 | All as per item No 107 herein before but wiring with 2.5 sqmm copper wire (FRLSH) and 1.5 sqmm earth wire for switch socket combination 6 pin 15 amps on independent board. |
| 111 | S&F switch piano flush button single pole, one way 5 amps complete all as specified and directed. |
| 112 | S&F Socket outlet 2 in 1, 3 pin, 5A, flush type complete all as specified and directed. |
| 113 | S & F switch socket combination 2 in 1,5A, flush type complete all as specified and directed. |
| 114 | S & F Switch socket combination 2 in 1, 3 pin, 5 and 15 Amp flush type universal complete all as specified and directed. |
| 115 | S&F LED, 20 Watts, 4 ft, fittings complete with all accessories for mounting light fittings complete with earth terminal connection, 3 terminal/ PVC/ polycarbonate, isolated body complete all as specified and directed. |
| 116 | Supply and fix ceiling rose with earth terminal connection, 3 terminal/ PVC/ polycarbonate, isolated body complete all as specified and directed. |
| 117 | M & L Lamp holder, PVC/Polycarbonate type with cord grip cap suitable for pendant fittings complete all as specified and directed. |
| 118 | Supply and fix LED Bulb 9 Watt complete all as specified and directed. |
| 119 | S&F 09W/10W Bulk head luminiares including LED light driver holder connecting up with three core flexible copper conductor cable of suitable size complete all as specified and directed. |
| 120 | M & L for earthing complete with galvanised steel earth plate electrode 60x60cmx6.3 mm thick buried directly in ground (earth pit not less than 2.25 mtr deep below ground level) with top edge lead of the plate not less than 1.5 mtr below normal ground level, connected galvanised earth lead wire 4.0mm dia by means of bolts, nuts, check nuts and washers of galvanised iron or steel all as shown in Electrical plate No 3 connected to earthing test point all as specified or indicated including testing on completion, complete all as specified and directed. |
| 121 | S&F of distribution board single pole & neutral with 200 Amps rated bus bar, for single door IP-42 DB's, made out of sheet steel enclosure, recessed type, factory made powder coated 8 way -240 volts suitable for housing MCB's and isolator's complete in all fixing material/accessories etc complete all as specified and directed. |
| 122 | S&F MCB's single pole 240 volts 6 to 32Amps 10 KA 'C' series, complete all as specified and directed. |
| 123 | S & F of MCB SPN, 240volt, 40 to 63 Amp capacity, 10 KA, 'C' curve complete all as specified and directed. |
| 124 | M & L for Wiring for circuit/submain wiring along with earth wire with the following sizes of FRLSH PVC insulated copper conductor, single core cable in surface/recessed as required in PVC casing caping of size 2x6 sq. mm + 1x4 sq. mm earth wire, complete all as specified and directed. |
| 125 | Supply and fix exhaust fan made of sturdy Engineering plastic complete with louvers shutter, voltage 230V, 50 Hz, RPM 1200, Copper winding of sweep 300m complete all as specified and directed |
| 126 | Supply and installation and testing of Hot, Cold and normal Water Dispenser with refrigerator including all accessories 20 litre capacity, 230 volts, 50 hz, Refrigerant type R134a, including water bottle 20 ltr in capacity, complete all as specified and as directed. |
| 127 | Supply and fix electric water heater, storage type steel body with copper inner tank and heating element upto 2 KW capacity 50 litre, BEE 5 Star rated complete with all accessories such as safety valve, thermostat, NRV, connection piece etc, complete all as specified and directed. |
| 128 | Supply and laying or fixing or passing through pipe, 1100 volts grade heavy duty cable with PVC insulated aluminium conductor served with an inner sheathing of PVC tape armoured with galvanised steel wire or tape and overall PVC sheathed 16 sq. mm nominal cross section in service connections, complete all as specified and directed. |
| 129 | Supply and fixing round shape 12 watt 220 volts AC recessed type with high efficiency PMMA diffuser soft glare free light complete with drivers, holders, LED lamp suitable for roof ceiling including connecting up with three core flexible copper conductor cable of suitable size complete all as specified and directed. Please Enable Macros to View BoQ information |
AI Tender Summary
Tender Timeline
Jul 06, 2026
11:30 IST
Tender Published
Tender notice published.
CompletedJul 27, 2026
17:00 IST
Bid Submission Deadline
Online submission via eProcurement portal.
Upcoming · 15 daysJul 29, 2026
Bid Opening Date
Technical bids will be opened and evaluated.
Upcoming · 17 daysTender Documents
Download All (ZIP) ↓
Disclaimer
We takes all possible care for accurate & authentic tender information. However users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender