Tender For Provn Of Certain Revenue Works Against Job No. Stn Hq Awantipur/2025-26/Revenue /04 And Job No. 40 /Rev/Vf/2025-26 Under Age B/R (P) Of Ge 861 Ews
Tender Value
19.87 Lakhs
Estimated cost
Bid Submission
28 Jul 2026
22 days left
EMD
40000
Bank guarantee accepted
Document Fee
500
Non-refundable
Tender Type
Online
Tender Overview
Organization
Tender ID
Competition Type
NCB
Bidding Type
Tender
Location / State
Anantnag → Jammu and Kashmir
EMD Exemption
Not Available
Quantity
Not Available
Website
Contact Person
Address
Project Description
Tender for Provn Of Certain Revenue Works Against Job No. Stn Hq Awantipur/2025-26/Revenue /04 And Job No. 40 /Rev/Vf/2025-26 Under Age B/R (P) Of Ge 861 Ews
BOQ
| Sl. No. | Item Description |
| 1 | Excavating in trenches, not exceeding 1.5 m wide and not exceeding 1.5 m in depth; for foundation, etc. or for shafts, wells, cesspits, manholes, pier holes, cable, pipes etc. not exceeding 10 sqm on plan and not exceeding 1.5 m in depth and getting out in Hard / Dense soil complete all as specified and as directed by Engineer-in- charge. |
| 2 | Material and Labour for Excavating in post holes (or similar holes)each not exceeding 0.5 cum.getting out in hard/ dense soil,returning, filling in and ramming earth or broken rubble mixed with earth around,in layers not exceeding 25 cm in hard/dense soil complete all as specified and as directed by Engineer-in-Charge. |
| 3 | Returning filling including spreading , levelling, watering and well ramming in layers, each layer not exceeding 25cm in any type of soil complete all as specified and as directed by Engineer-in- charge. |
| 4 | Removing excavated material of any type of soil not exceeding 50m and depositing where directedc at a level n exc 1.5 mtr above the starting point . complete all as specified and directed by Engr- in- charge. |
| 5 | Surface excavation not exceeding 30 cm deep and averaging 15cm deep and getting out in Hard/Dense soil complete all as specified and as directed by Engineer-in- charge. |
| 6 | Material & Labour for PCC 1:4:8 , Type - D2, using 40mm graded stone aggregates as in foundations, filling and mass concrete complete all as specified and directed by Engineer-in-Charge. |
| 7 | Material & Labour for PCC 1:3:6 , Type - C2, using 40mm graded stone aggregates as in foundations, filling and mass concrete complete all as specified and directed by Engineer-in-Charge. |
| 8 | Material & Labour for Reinforced cement concrete (Design Mix) M-25 as in foundations, including rafts, footings, foundation beams; plinth beams; bases for columns, etc.; basement slabs, under-reamed piles and mass concrete complete all as specified and as directed by Engineer-in-Charge.NOTE :- Form work and Steel reinforcement shall be measured and paid seperately under appropriate items of Schedule 'A' BoQ. |
| 9 | Material & Labour for Reinforced cement concrete (Design Mix) M-25 as in Columns, pillars, piers, posts and struts complete all as specified and directed by Engineer-in-Charge.NOTE :- Form work and Steel reinforcement shall be measured and paid seperately under appropriate items of Schedule 'A' BoQ. |
| 10 | Material & Labour for Reinforced cement concrete (Design Mix) M-25 as in Beams, cantilevers, bressummers, lintels over 1.5m span complete all as specified and directed by Engineer-in-Charge.NOTE :- Form work and Steel reinforcement shall be measured and paid seperately under appropriate items of Schedule 'A' BoQ. |
| 11 | Material & Labour for Reinforced cement concrete (Design Mix) M-25 as in Slabs supported on walls,beams and columns infloors,roofs, landings, balconies,canopies, deck slabs and inshelves and the like Slabs supported on walls,beams andcolumns in floors,roofs, landings, balconies,canopies, deck slabs and inshelves and the like complete all as specified and directed by Engineer-in-Charge.NOTE :- Form work and Steel reinforcement shall be measured and paid seperately under appropriate items of Schedule 'A' BoQ. |
| 12 | Material & Labour for formwork to sides of concrete foundations, footings, bases of columns, raft and raft beams, sides and soffits (if any) of foundation and plinth beams; and similar work; vertical or to batter on rough finished flat surface of concrete complete all as specified and as directed by Engineer-in-Charge. |
| 13 | Material & Labour for Formwork to sides of pillars, posts, struts, piers, columns and stanchions, in square, rectangular or polygonal on rough finished surface of concrete complete all as specified and as directed by Engineer-in-Charge. |
| 14 | Material & Labour for Formwork to sides and soffits of floor or roof beams, beam haunchings, girders, bressummers, lintels, cantilevers, shelves including sup- ports, overhangs, etc. also splays between floors and beams, etc. on flat rough finished surface of concrete complete all as specified and as directed by Engineer-in-Charge. |
| 15 | Material & Labour for Formwork to soffits of suspended slabs such as roof slabs, floor slabs, landings and similar work; not exceeding 200mm thick (Horizontal or sloping) on rough finished flat surface of concrete complete all as specified and as directed by Engineer-in-Charge. |
| 16 | Material & Labour for Mild steel TMT bars 10mm dia in stirrups, spacers and binders, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and as directed by Engineer-in-Charge. |
| 17 | Material & Labour for Mild steel TMT bars 5mm dia and over upto and including 10mm dia in stirrups, spacers and binders, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and as directed by Engineer-in-Charge. |
| 18 | Material and labour Brickwork with sub class 'B' old size burnt clay bricks, straight or curved on plan exc 6m mean radius in cement mortar 1:4 complete all as specified and as directed by Engineer-in-charge. |
| 19 | Material and labour Brickwork with sub class 'B' old size burnt clay bricks, straight or curved on plan to any radius in half brick thick walls built in cement mortar 1:4 complete all as specified and as directed by Engineer-in-charge. |
| 20 | Material & Labour for Sand filling under floors or in foundations including watering and consolidation complete all as specified and directed by Engineer-In-Charge. |
| 21 | Material & Labour for Hardcore of broken stone or boulders ,gauge not exceeding 63mm but , deposited, spread and levelled in layers not exceeding 15 cm thick, watered and rammed to a true surface complete all as specified and as directed by Engineer-in-Charge. |
| 22 | Material & Labour for 100 mm thick PCC 1:4:8 ,Type-D2 ,using 40mm graded stone aggregates as in sub base of flooring complete all as specified and directed by Engineer-in-Charge. |
| 23 | Material & Labour for 75 mm thick PCC 1:3:6 ,Type-C1 ,using 20mm graded stone aggregates as in sub base of floor finished of plinth protection complete all as specified and directed by Engineer-in-Charge. |
| 24 | Material & Labour for Non skid ceramic coloured , thickness 7mm to 8mm thick (square/ rectangular), colour as approved by Engineer-in-charge area of each tiles exceeding 0.11 Sqm but not exceeding 0.18 Sqm in floor etc set and jointed in neat cement slurry @ 3.00Kg per Sqm and pointed in white or coloured cement to match the colour / shade of tiles , laid over with and including 15mm thick screed bed in cement mortar 1:4 complete all as specified and directed by Engineer-in-Charge. |
| 25 | Material & Labour for Non skid ceramic coloured joint free tiles , thickness 7mm to 8mm thick (square/ rectangular), colour as approved by Engineer-in-charge area of each tiles exceeding 0.18 Sqm but not exceeding 0.38 Sqm in floor etc set and jointed in neat cement slurry @ 3.00Kg per Sqm and pointed in white or coloured cement to match the colour / shade of tiles , laid over with and including 15mm thick screed bed in cement mortar 1:4 complete all as specified and directed by Engineer-in-Charge. |
| 26 | Material & Labour for Glazed ceramic coloured tiles size 350mm x 250mm x 7mm /450mm x 350mm x 7mm thick as in verticle surface , set and jointed in neat cement slurry @ 3.00Kg per Sqm and pointed in white or coloured cement to match the colour / shade of tiles , laid over with and including 10mm thick rendering in cement mortar 1:4 complete all as specified and directed by Engineer-in-Charge. |
| 27 | Material & Labour for Factory made, Machine Pressed Precast concrete Glossy Interlocking paver block with grey cement and pigment, any shape and size, conforming to IS 15658-2006 of 60 mm thickness, made out of M-35 grade concrete laid over sand cushioining complete all as specified and as directed by Engineer-in-charge. Note:Sand cushioning shall be measured and paid seperately under approriate item of Schedule'A' BoQ. |
| 28 | Supply & Fixing Mild steel work as in Framed work such as grills, gratings, etc.. with ends of bars shouldered and/or riveted, or forged into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; framework of water tanks and similar work conforming to Fe.290 Gde-E-165 complete all as specified and as directed by Engineer-in-Charge. |
| 29 | Supply & Fixing Mild steel work as in Hand rails, half round or other steel section or core for wooden hand-rail straight portion, drilled and countersunk for balusters running bars, for doors, balusters, nosing to steps including embeding in concrete and screwing etc. wind ties for roof including securing bolts; posts and struts in fencing including cutting tops to shape as directed, drilling holes, notching for wire, etc.; flat iron fillets (for securing wire mesh etc.) including all necessary drilling, bolting or riveting, etc., and similar work conforming to Fe-290 Gde E-165 complete all as specified and as directed by Engineer-In-Charge. |
| 30 | Supply and Fixing Galvanised mild steel wire cloth, 0.63mm nominal dia of wire and average width of aperture 1.40mm and fixed with tinned tacks, or galvanised wire staples complete all as specified and directed by Engineer-in-Charge. |
| 31 | Supply & Fixing Wire netting ( size of mesh 12mm )of galvanised steel wire 1.40mm dia fixed with tinned tacks of wire staples complete all as specified and directed by Engineer-In-Charge. |
| 32 | Supply & Fixing Mild steel work as in Roof trusses (framed), trussed, purlins, crane gantries, rails and fastenings and heavy bracket framing (Beam, tee, angle, channel or flat sections) Fe 410 -W (Gde- E- 250) quality-A including distance pieces, cleats etc complete all as specified and as directed by Engineer in charge. |
| 33 | Supply & Fixing Pre- painted galvalume aluminum zinc coating GI based corrugated steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws as specified complete all as specified and directed by Engineer-in-Charge. |
| 34 | Supply & Fixing Pre-painted galvalume aluminum zinc coating GI based Plain steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws as specified complete all as specified and directed by Engineer-in-Charge. |
| 35 | Material and labour for Rendering 10mm thick in Cement Mortar 1:4 , on fair faces of brick work or concrete surfaces of walls , finish even & smooth without using extra cement complete all as specified and directed by Engineer-in-Charge. |
| 36 | Material and labour for Rendering 15mm thick in Cement Mortar 1:6 , on fair faces of brick work or concrete surfaces of walls , finish even & smooth without using extra cement complete all as specified and directed by Engineer-in-Charge. |
| 37 | Material and labour for Rendering 15mm thick in Cement Mortar 1:4 , on fair faces of brick work or concrete surfaces of walls , finish even & smooth without using extra cement complete all as specified and directed by Engineer-in-Charge. |
| 38 | Supply & Fixing Solid PVC door frame of size 50mm x 47mm made out of 5 mm single side prelam PVC sheet reinforced with MS square tube manufactured as per SSR Part-I specifications and drawings complete all as specified and directed by Engineer-in-Charge. |
| 39 | Supply & Fixing Factory made solid panel PVC door shutter 30 mm thick (style) consisting of frame made out of M.S. tubes for top & bottom rails. M.S. frame shall be covered with heat moulded plain colour PVC ‘C’ channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail; Panelling of plain colour PVC sheet to be fitted in the M.S. frame welded / sealed to the stiles & rails with suitable PVC sheet beading, and joined together with solvent cement, suppling & fixing in the frame at site as per specification & drawing. complete all as specified and directed by Engineer-in-Charge. |
| 40 | Supply & Fixing second class hard wood plain, solid, straight chowkats and frames wrought, framed rebated on the solid rounded or chamfered, put together with glue pinned at joints complete all as specified and directed by Engineer-in-Charge. |
| 41 | Supply and Fixing Factory made 35mm thick framed, panelled shutter (two panel) with lock rail made of 2nd class Hard wood and panel of 9 mm B.W.P. commercial ply or 12 mm veneered particle board with commercial veneering on both faces. The size of rail and stile as per IS : 1003 (Part I), kiln seasoned and chemically pressure treated complete all as specified and directed by Engineer-in-Charge. Note: Butt Hinges, Tower bolts, Handles , sliding door bolts and painting shall be measured and paid seperately under appropriate items of schedule 'A' BoQ. |
| 42 | Supply and Fixing Butt hinges size of 100mm , medium weight cold rolled mild steel (ISI Marked) complete all as specified and directed by Engineer-in-Charge. |
| 43 | Supply and Fixing Butt hinges size of 100mm , extruded aluminium alloy with galvanised mild steel hinge pin, anodised and fixed, type B-21 (ISI Marked) complete all as specified and directed by Engineer-in-Charge. |
| 44 | Supply and Fixing 150mm long aluminium anodised barrel tower bolts of extruded section (ISI Marked) complete all as specified and directed by Engineer-in-Charge. |
| 45 | Supply and Fixing 200mm long aluminium anodised barrel tower bolts of extruded section (ISI Marked) complete all as specified and directed by Engineer-in-Charge. |
| 46 | Supply and Fixing aluminium alloy, anodised, sliding door bolt of length 300 mm with hasp, staple (bolt type) (ISI Marked ) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of sections or cast-aluminium extruded alloy and fixed complete all as specified and directed by Engineer-in-Charge. |
| 47 | Supply and Fixing 150 mm long Extruded aluminium alloy handles, fabricated type,anodised (ISI Marked) as specified and directed by Engineer-in-Charge. |
| 48 | Material and labour for preparation of new surface of walls, with and including two coats of cement base paint ,over with and including one coat of alkali resistant priming paint complete all as specified and directed by Engineer-in-Charge. |
| 49 | Material and labour for preparation of newly plastered surfaces of walls , with and including applying three coats of white wash over with and including one coat of chalk white primer complete all as specified and as directed by Engineer-in-charge. |
| 50 | Material and labour for preparation of new plastered surface of walls with and including applying two coats of Oil bound Distemper over with and including one coat of alkali resistant priming paint complete all as specified and directed by Engineer-in-Charge. |
| 51 | Material & Labour for preparation of newely steel surfaces of any description, over 10 cm in width or girth or otherwise described , with and including applying two coat of syntheic enamal paint over with and including one coat of red oxide zinc chrome primer complete all as specified and as directed by Engineer-in-Charge. |
| 52 | Material and Labour for preparing for newly wood or wood based surfaces of any description over 10 cm width or girth and applying two coats of synthetic enamel paint over with and including one coat of pink primer complete all as specified and as directed by Engineer-in-charge. |
| 53 | Supply & fixing Rotational moulded polyethylene water storage tank white colour of capacity 500 litres (cylindrical vertical, triple layered with closed top), hoisted and fixed in position with and including 20mm bore ball valves, high pressure of PTMT with epoxy coated aluminium rod and high density plastic ball (polythene float) complete all as specified and as directed by Engineer-in-charge. Note: The rate of 20mm bore ball valves, high pressure of PTMT is included in this item and nothing shall be paid extra on this account. |
| 54 | Supply & fixing Rotational moulded polyethylene water storage tank white colour of capacity 1000 litres (cylindrical vertical, triple layered with closed top), hoisted and fixed in position with and including 20mm bore ball valves, high pressure of PTMT with epoxy coated aluminium rod and high density plastic ball (polythene float) complete all as specified and as directed by Engineer-in-charge. Note: The rate of 20mm bore ball valves, high pressure of PTMT is included in this item and nothing shall be paid extra on this account. |
| 55 | Supply & Fixing 15mm bore GI tubing medium grade with all new fittings to walls and ceilings or laid in floors complete all as specified and directed by Engineer-in-Charge. |
| 56 | Supply & Fixing 20mm bore GI tubing medium grade with all new fittings to walls and ceilings or laid in floors complete all as specified and directed by Engineer-in-Charge. |
| 57 | Supply and fixing 20mm bore Gun metal, globe or gate valve (ISI marked), brass cast copper alloy, with iron wheel head, screwed both ends suitable for iron pipes complete all as specified and as directed by Engineer-in-charge. |
| 58 | Supply and fixing 15mm bore bib tap cast copper alloy, chromium plated, fancy type (ISI marked) with crutch or butterfly handle with capstan head, screwed down, screwed for iron pipe or for brass ferrule complete all as specified and as directed by Engineer-in-charge. |
| 59 | Supply and Fixing Vitreous china wash hand basin, Vitreous china white, flat back, size of 630mm x 450 mm, with and including Mild steel brackets, with and including cutting for and pinning in ends of brackets or erecting stand, with and including waste fittings of brass chromium plated ,with and including 32mm dia PVC waste pipe of required length complete all as specified and directed by Engineer-in-Charge. |
| 60 | Supply and fixing 15 mm bore stop valve , Chromium Plated, Fency type cast copper alloy (ISI marked) screwed down , high pressure with crutch or butterfly handle fancy type complete all as specified and directed by Engineer-in-Charge. |
| 61 | Supply & Fixing 15mm bore PVC connection with PTMT nuts of 600mm long complete all as specified and directed by Engineer-in-Charge. |
| 62 | Supply & Fixing 100mm bore Cast iron floor trap of , (ISI Marked ) ,with grating including jointing to waste pipe fixed in cement concrete 1:2:4 Type B-1, using 20mm stone aggregates complete all as specified and directed by Engineer-in-Charge. |
| 63 | Supply and fixing PVC (SWR) 110 mm bore pipes single socketed ,Type-B (ISI Marked ) fixing with using adhesive, in any length laid in trenches or in floors complete all as specified and directed by Engineer-in-Charge.Note: Excavation and earth work shall be measured and paid seperately under appropriate items of Schedule of BoQ. |
| 64 | Supply & Fixing water closet vitreous china squatting pan, Orissa pattern size 580mm x 440mm white with integral foot rests with and including provision of lime concrete bedding with and including 110mm bore PVC (SWR)'P' Trap and connection to drain and to flushing pipe anti symphonage pipe complete all as specified and directed by Engineer-in-Charge. |
| 65 | Supply and Fixing PVC valveless, syphonic action type, flushing cistern, 10 litres capacity, low level, white, with inlet, ball valve, float and handle , with and including brackets, with and including 32 mm dia flush pipe of polyethylene of low or high density of PVC complete all as specified and as directed by Engineer-in- charge. |
| 66 | Supply and Fixing 110mm PVC (SWR) WC connector bent type complete all as specified and as directed by Engineer-in- charge. |
| 67 | Supply and fixing 150mm bore Reinforced concrete pipes, class NP3, laid and jointed complete with collars complete all as specified and directed by Engineer-in-Charge. |
| 68 | Material and labour for PCC (1:3: 6) type C-2 using 40 mm graded stone aggregates as in concrete bed for drain pipes of 150 mm bore, laid to required slope including packing under and haunching against the sides of pipes after they are laid and tested including form work complete all as specified and as directed by Engineer-in-charge. Note :- (i) Thickness of concrete bed below the barrel of pipe shall be 10 cm. (ii) Width of concrete bed shall be outer diameter of drain pipes (not of sockets / collar) plus 30cm.(iii) Excavation , earth work , returning filling shall be measured and paid seperately under appropriate items of schedule 'A' BoQ. |
| 69 | Material and Labour for Cutting into existing manholes for connecting new drains, making good to pipe and rendering, cutting out existing benching for and forming branch channel (1/2 round or 3/4 section) in cement concrete 1:2:4 type B-l smooth finished, and reforming benching as required for internal dia of pipe 150mm complete all as specified and as directed by Engineer-in-charge. |
| 70 | Material and labour for Point wiring using approved colour coding as per IS (Red, Black and Green for single phase circuits),with 1.5 Sqmm two single core PVC insulated, multistranded, unsheathed, FRLSH copper conductor cable 1100 volt grade ISI Marked , with and including PVC casing and capping of medium grade of suitable size and run on wall / surface with all fittings (ISI Marked) with and including one single core 1.5 Sqmm FRLSH PVC insulated multi strand copper conductor cable 1100 volt grade (ISI marked ) (as in green colour) as continues earth wire connected to earth dolly etc. controlled by one switch for one light point/ fan point with and including PVC Gang Box of required size & as directed by Engineer- in- Charge including cutting, chases to wall making good the disturbed surfaces to match with the existing specification complete all as specified and directed by Engineer-in-Charge. Notes for serial item nos.70.00 to 73.00 : (i) Switches one way 5 /6 Amp , Switch Socket combination 5 /6 Amp , Switch Socket combination 15 1/6 Amp , fan regulator shall be measured and paid seperately under respective items of Schedule'A' BoQ. |
| 71 | All as per srl item No-70.00 here in before but for one Switch socket combination 2 in 1, 3 pin, 5 Amp independent controlled by one switch complete all as specified and directed by Engineer-in-Charge. |
| 72 | All as per srl item No-70.00 here in before but for one Switch socket combination 2 in 1, 3 pin, 5 Amp on the same board controlled by one switch complete all as specified and directed by Engineer-in-Charge. |
| 73 | All as per srl item No 70.00 of BoQ here-in-before but 2.5 Sqmm two single core PVC insulated, multistranded, unsheathed, FRLSH copper conductor cable 1100 volt grade ISI Marked with and including one single core 2.5 Sqmm FRLSH PVC insulated multi strand copper conductor cable 1100 volt grade (ISI marked ) as continues earth wire connected to earth dolly etc Switch socket combination 2 in 1, 3 pin, 15 Amp complete all as specified and directed by Engineer-in-Charge. |
| 74 | Material and labour for concealed Point wiring using approved colour coding as per IS (Red, Black and Green for single phase circuits), in new PVC conduit complete with and including 1.5 Sqmm two single core PVC insulated, multistranded, unsheathed, FRLSH copper conductor cable 1100 volt grade ISI Marked , drawn through with and including new PVC rigid conduit 20mm dia ( heavy duty ) ISI marked with valid CML No.(IS-9537-1983 for conduits and IS:3419:1976 for conduit accessories) with all new fittings and all accessories i.e pipe bend pipe hook, elbow,junction box, pressed steel powder coated sunken box of suitable size (min 60mm deep, suitable length and 1.2mm thick ) and flush fixed with cement mortar 1:4 , 3mm thick bakelite plastic laminated sheet for mounting with frame and top cover for switches 5Amp/6Amp , socket outlet 5Amp/6Amp and fan regulator, for light / fan point controlled by one way switch 5Amp / 6Amp, top cover fixed with brass screws & cup washers, with and including one single core 1.5 Sqmm FRLSH PVC insulated multi strand copper conductor cable 1100 volt grade (ISI marked ) (as in green colour) as continues earth wire connected to earth dolly etc. with and including cutting chases (as required) and making good surfaces to match with adjoining surface complete all as specified and as directed by Engineer-in- charge .Notes for serial item nos. 74.00 to 76.00 : (i) Switches one way 5 /6 Amp , Switches one way 15 /16 Amp, Socket out lets 5 /6 Amp and Socket out lets 15 1/6 Amp, shall be measured and paid seperately under appropriate items of Schedule 'A' BoQ. |
| 75 | All as per serial item No 74.00 of BoQ here-in-before but for socket outlet 5 pin 5Amp /6 Amp on same board, complete all as specified and directed by Engineer-in-charge. |
| 76 | All as per serial item No 74.00 of BoQ here-in-before but 2.5 Sqmm two single core PVC insulated, multistranded, unsheathed, FRLSH copper conductor cable 1100 volt grade ISI Marked with and including one single core 2.50 Sqmm FRLSH PVC insulated multi strand copper conductor cable 1100 volt grade (ISI marked ) as continues earth wire connected to earth dolly etc for 3 pin socket outlet 15 Amps with complete all as specified and directed by Engineer-in-Charge. |
| 77 | Supply & Fixing switch piano flush type, 05 / 06 Amps single pole, one way 240 volts complete all as specified and directed by Engineer-in-Charge. |
| 78 | Supply & Fixing Switch socket combination 2 in 1, 3 pin, 5 Amp flush type universal 240 volt complete all as specified and directed by Engineer-in-Charge. |
| 79 | Supply & Fixing Switch socket combination 2 in 1, 3 pin, 15 Amp flush type universal 240 volt complete all as specified and directed by Engineer-in-Charge. |
| 80 | Supply and fixing ceiling rose PVC/ Polycarbonate insulated body type, 3 terminals, 240 volts, 5 Amps complete all as specified and directed by Engineer-in-Charge. |
| 81 | Supply and fixing Socket outlet 5 pin 5 Amps flush type multi purpose ISI marked complete all as specified and directed by Engineer-in-Charge. |
| 82 | Supply and fixing Socket outlet multipurpose 2 in one, 6 pin 15 Amps flush type ISI marked complete all as specified and directed by Engineer-in-Charge. |
| 83 | Supply and fixing Switch piano flush type 15 Amp single pole one way ISI marked complete all as specified and directed by Engineer-in-Charge. |
| 84 | Supply & Fixing Flood Light 70 Watt 230 Volt , AC, outdoor type with high pressure die cast aluminium hosing and heat resistant complete with driver, lamp bracket with impact and corrosion resistant including thermal mangement in multiple optics complete with IP -66 Protection complete all as per manufacturer's insutructions and including connecting up with driver from ceiling rose with three core flexible copper conductor cable of suitable size complete all as specified and directed by Engineer-in-Charge. Notes:-(a) Contractor has to furnish a replacement warranty of 02 years for Flood LED Light fittings complete including from the certifiy date of completion of CA. The product will be replaced free of cost in the following case :-(i) Manufacturing defects.(ii) Failure due to mechanical and electrical impact. (iii) Drop in lumen (or lux at 1 m) below 90% of clamied values of lumen(or lux at 1 m) of the LED /Luminaries. (b) All LED light must meet the provision laid down in IS - 16101, 16102 Part -I/II,16103 Part -I, 16104,16105,16106, 16108/2012 and 15885 Part -II / Section 13. (c) Scope of work shall include Flood LED Light fittings walls/ceiling which includes needful T & P and required accessories etc if any, complete including making connection, testing etc complete. No extra payment is admissible on these account. |
| 85 | Supply and fixing lamp holder (Angular / Straight), insulated body, with back plate for batten fitting complete all as specified and directed by Engineer-in-Charge. |
| 86 | Supply and Fixing Decorative ultra slim linear LED 20 Watt 4 Feet Long lighting fixture with extruded aluminium heat sink,environment friendly, Energy efficient , ready to use pack with and including LED Tube complete , with inbuilt electronic driver, PCB, Connector block complete all as per manufactureres instructions with and including connecting up with theree copper flexible cable from ceiling rose to fitting including connectiong up and fixed on with and including two nos.square box of required size complete all as specified and directed by Engineer-in-charge. Notes:(a) Contractor has to furnish a replacement warranty of 02 years for LED light fittings complete including from the certifiy date of completion of CA. The product will be replaced free of cost in the following case :-(i) Manufacturing defects.(ii) Failure due to mechanical and electrical impact. (iii) Drop in lumen (or lux at 1 m) below 90% of clamied values of lumen(or lux at 1 m) of the LED /Luminaries. (b) All LED light must meet the provision laid down in IS - 16101, 16102 Part -I/II,16103 Part -I, 16104,16105,16106, 16108/2012 and 15885 Part -II / Section 13. (c) Scope of work shall include LED fittings walls/ceiling which includes needful T & P and required accessories etc if any, complete including making connection, testing etc complete. No extra payment is admissible on these account. |
| 87 | Supply & Fixing LED Lamp 9 W complete all as specified and directed by Engineer-in-Charge. |
| 88 | Supply and fixing sheet metal enclousers made out of CRCA mild steel sheet , IP-43 protection, flush mounted with metal door, powder coated DB SPN 8 way 230 V AC with 200 Amp rated copper bus bar, Double Door, dust and vermin proof suitable for incorporation of MCBs / MCCBs/ Isolators etc.conforming to IS/IEC-61439-2:2011, BS-5484 complete all as specified and directed by Engineer-in-charge. Notes: (i)MCBs / MCCBs/ Isolators shall be measured and paid seperately under appropriate items.(ii) The rate of 200 Amps copper bus bar is included in this item and nothing shall be paid extra on this account. |
| 89 | Supply and fixing MCB SP 6 to 32 Amps, 230 volts , AC supply , rupturing capacity not less than 10KA,' C' Curve ,ISI Marked, with and including necessary attachment , thimbles etc complete all as specified and directed by Engineer-in-charge. |
| 90 | Supply and fixing MCB SPN 32 Amp , rupturing capacity not less than 10 KA 'C' curve 230 V AC, 50 Hz ,ISI Marked, with and including necessary attachment , thimbles etc. complete all as specified and directed by Engineer-in-charge. |
| 91 | Supply and fixing MCB SPN 40Amps to 63 Amp , rupturing capacity not less than 10 KA 'C' curve 230 V AC, 50 Hz ,ISI Marked, with and including necessary attachment , thimbles etc. complete all as specified and directed by Engineer-in-charge. |
| 92 | Supply & Fixing Ceiling fan of 1200mm sweep complete with blades, down rods, with and including electronic regulator (modular type, 120w, 2 module) and accessories, 230 Volts, single phase, 50 Hz, Min air delivery 210 CFM with service value 6.00 BEE. Five star rated with brushless direct current (BLDC) motor connecting up complete with and including three core flexible PVC insulated multi stranded copper conductor cable of suitable size from ceiling rose / connector, complete all as specified and directed by Engineer-in-Charge. |
| 93 | Supply and fixing Exhaust fan made of sturdy Engineering plastic complete with louvers shutter, voltage 230V, 50 Hz, RPM 1200, Copper winding of sweep 300mm complete all as specified and directed by Engineer-in-Charge. |
| 94 | Supply and Fixing water heater (Geyser) Auto restrat and safety measures type electrical operated 230/240 Volts 25 ltr capacity, BEE 5 star rated complete with all safety equipment and accessories such as safety valve, thermostat, plug top, etc. required for proper functionality & including electric/earth connections and carrying out grounting & complete installations with mounting bolts,nuts including testing after installation complete all as specified & directed by Engr-in- Charge. |
| 95 | Supplying and fixing 1100 volts grade heavy duty cable PVC insulated aluminium Solid conductor, served with inner sheathing of PVC tape and overall PVC sheathed in service connections suspended by insulating hangers not more than 1 metre apart including 4mm suspension wire, one twin core cable flat or circular of cross sectional area 10Sqmm complete all as specified and directed by Engineer-in-Charge. |
| 96 | Material and Labour for Earthing complete with galvanised steel earth plate electrode 600mm x 600mm x 6 mm thick burried directly in ground to depth of pit not less than 2.25 m below normal ground level with top edge of the plate not less than 1.5 m below normal ground level surrounded from all sides by 15 cm thick packed layer of charcoal / coal dust and common salt filling in alternate layers and connected to galvanised earth lead wire 4 mm dia by means of bolts, nuts, check nuts and washers of GI or steel including GI protection pipe 15mm dia light grade upto the extent of 7.5 metre and connecting to earthing test point, main switch board including GI pipe 20 mm dia medium grade for watering, MS funnel and bringing out the watering pipe upto 30 cm above the normal ground level plugged at top including all fitting including PCC earth pit with PCC 1:2:4 type B-1 using 20mm graded stone aggregate and RCC pit cover including necessary earthwork and excavation in any type of soil complete all as specified as shown in electrical plate No 3 of SSR Part-I and testing on completion. Note:- (i) Earth continuity of GI wire 4 mm including protection pipe up to 7.5 mtrs from earth electrode will be included in unit rate, complete all as specified and directed. (ii) The rate of earth work in soft/loose soil i.e. excavation, returing filling and removal, form work is included in this item and nothing shall be paid extra on this account. (iii) PCC chamber shall be constructed at least 1.5 metre away from the earth electrode and pipe for watering shall be provided in slanting manner. (iv) The earth testing arrangement should be done by the contractor as per direction of Engineer-in-charge. |
| 97 | Material and Labour Sub main wiring with two single core of size 4.0 Sqmm FRLSH PVC insulated unsheathed with multistranded copper conductor cable 1100 volts grade ISI Marked including cuttting, chasing and grouting , with and including non metallic rigid PVC conduit medium quality of size 25 mm dia conforming to 3537 Part-I ISI marked including all fitting such as Tee, Elbow, bend etc drawn in and including one single core of size 4.0 Sqmm FRLSH PVC insulated unsheathed with multistranded copper conductor cable 1100 volts grade ISI Marked as in contineous earth conductor cable connected to earth dolly complete all as specified and as directed by Engineer-in- charge. (Colour code phase-Red, Neutral-black and Earth as Green) complete all as specified and as directed by Engineer-in- charge. Notes:-(a) Cost of PVC conduit , conduit accessories and earth wire included in sub main wiring. (b) Three single core 4.0 Sqmm FRLSH PVC insulated unsheathed with multistranded copper conductor cable 1100 volts grade ISI Marked with and including non metallic rigid PVC conduit of size 25 mm ISI Marked dia shall be measured as one length. |
| 98 | Supply and Fixing 20mm dia (Outer diameter of pipes in mm) 3- layer PP-R Polypropylene random copolymer) concealed pipes SDR 7.4 (PN16) UV stabilized and antimicrobial fusion welded having thermal stability for hot & cold water supply all PP-R plain & brass threaded polypropylene random fittings laid in trenches complete all as specified and as directed by Engineer-in-charge. Note: Earth work and excavation shall be measured and paid seperately under appropriate items of Schedule 'A' BoQ. |
| 99 | Supply and Fixing 20mm dia (Outer diameter ) 3- layer PP-R gate valves (base insert ) as per site requirement complete all as specified and as directed by Engineer-in-charge. |
| 100 | Material and Labour for Cutting of existing PP-R pipe line of 20mm to 75mm bore and inserting with and including NEW PP-R TEE of appropriate size and taping new connection with all accessories complete all as specified and as directed by Engineer-in-charge. Note: The rate of supply and fixing of NEW PP-R TEE of appropriate size is included in this item.Hence bidder shall be quoted his rates accordingly and nothing shall be paid extra on this account. Please Enable Macros to View BoQ information |
AI Tender Summary
Tender Timeline
Jul 06, 2026
11:30 IST
Tender Published
Tender notice published.
TodayJul 28, 2026
17:00 IST
Bid Submission Deadline
Online submission via eProcurement portal.
Upcoming · 22 daysJul 31, 2026
Bid Opening Date
Technical bids will be opened and evaluated.
Upcoming · 25 daysTender Documents
Download All (ZIP) ↓
Disclaimer
We takes all possible care for accurate & authentic tender information. However users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender