Tender For Special Repair To Bldg No.Os-3,Os-5,Clb-1,Clb-2,Clb-6 Of 10 Mahar And Special Repair/Replacement Of Ber Summer Appliances At Lekhapani Mil Stn Under Ge Dinjan No.2
Tender Value
26.50 Lakhs
Estimated cost
Bid Submission
25 Jul 2026
18 days left
EMD
53000
Bank guarantee accepted
Document Fee
500
Non-refundable
Tender Type
Online
Tender Overview
Organization
Tender ID
Competition Type
NCB
Bidding Type
Tender
Location / State
Tinsukia → Assam
EMD Exemption
Available
Quantity
Not Available
Website
Contact Person
Address
Project Description
Tender for Special Repair To Bldg No.Os-3,Os-5,Clb-1,Clb-2,Clb-6 Of 10 Mahar And Special Repair/Replacement Of Ber Summer Appliances At Lekhapani Mil Stn Under Ge Dinjan No.2
BOQ
| Sl. No. | Item Description |
| 1 | Dismantling wrought iron or mild steel work of any description complete all as specified and directed by Engineer-in-Charge. |
| 2 | Dismantling of plain or corrugated steel sheeting any guage, thickness including Nanital or similar pattern roof coverings complete all as specified and directed by Engineer-in-Charge. |
| 3 | Dismantling boarding, any description fixed in any position with nails complete all as specified and directed by Engineer-in-Charge. |
| 4 | Demolition of unreinforced cement concrete in ground floors and pavings n. exc 15 cm thickness (below or above ground level) complete all as specified and directed by Engineer-in-Charge. |
| 5 | Taking down chowkat or frame with shutters (without taking off shutters from the frame) not exceeding 1.5 sqm each and making good to disturbed surfaces complete all as specified and directed by Engineer-in-Charge.. |
| 6 | Taking down chowkat or frame with shutters (without taking off shutters from the frame) exceeding 1.5 sqm but not exceeding 4.0sqm each and making good to disturbed surfaces complete all as specified and directed by Engineer-in-Charge. |
| 7 | S&F 30 mm thick, flush shutters, solid core construction, with block board core and plywood face panels, commercial type on both sides & both face is covered with decorative face veneer with lipping / frame to match & fixed to chowkats complete all as specified and directed by Engineer-in-Charge.. |
| 8 | S&F 30 mm thick, hard wood Glazed and skeleton shutters, open rebated and prepared to receive glass, gauze, etc. (without sash bars), edges of framing plain, chamfered or rounded. fitted with cut and mitred beads for securing glass, etc.; sizes of me-mbers of shutters as specified in SSR Part I, Section 8, clause 8.24 (a) fitted to chowkats complete all as specified and directed by Engineer-in-Charge. |
| 9 | S&F factory made solid panel PVC door shutter 30 mm thick (style) consisting of frame made out of M.S. tubes for top & bottom rails. M.S. frame shall be covered with heat moulded plain colour PVC ‘C’ channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail; Paneling of plain colour PVC sheet to be fitted in the M.S. frame welded/sealed to the stiles & rails with suitable PVC sheet beading, and joined together with solvent cement complete fixed to frames complete all as specified and directed by Engineer-in-Charge. |
| 10 | S&F Steel ventilators with centre hung shutter including two pairs of brass cup pivots, catch spring and pulley wheel,complete all as specified and directed by Engineer-in-Charge. |
| 11 | S&F 150 mm size, aluminium anodised , barrel tower bolts of extruded section & fixed complete all as specified and directed by Engineer-in-Charge.. |
| 12 | S&F MS butt hinges,medium weight, cold rolled 125mm long fix with chowkat complete all as specified and directed by Engineer-in-Charge. |
| 13 | Supply only 2nd Class hard wood small fittings such as brackets of any type ,latch and hinge blocks,shaped door and window stops and like ,including all necessary labours,articles n exc 200Cu.cm each complete all as specified and directed by Engineer-in-Charge. |
| 14 | S&F stainless steel wire cloth 0.36 mm nominal dia of wire and average width of aperture 1.40 mm and fixed with stainless steel wire staples complete all as specified and directed by Engineer-in-Charge. |
| 15 | S&F 200 mm size, aluminium anodised , barrel tower bolts of extruded section & fixed complete all as specified and directed by Engineer-in-Charge. |
| 16 | S&F 150mm size aluminium handles, cast type, anodized and fixed complete all as specified and directed by Engineer-in-Charge. |
| 17 | S&F 300mm length of bolt, aluminium alloy, anodized, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast aluminium alloy complete all as specified and directed by Engineer-in-Charge. |
| 18 | S&F 375mm long Mild steel ordinary rat tail rod pattern springs for door including roller and roller plate complete all as specified and directed by Engineer-in-Charge. |
| 19 | S & F for aluminum powder coated (powder coated of required colour) three track sliding windows frame top & sides of size 92 x 31.75 x 1.50mm (section No 20831) bottom of size 92 x 31.72 x 1.50mm (Soction of 20832) and shutter top & bottom of size 40 x 18 x 1.55 (section 20738) and lock side shutter frame of size 40 x 15 x 1.45mm (Section 20737) with rubber gasket, beading and locking arrangement including making good to the disturbed portion complete including stainless steel wire mesh 0.36mm nominal dia with 1.40mm average aperture and fixed with stainless steel wire staples and fixing 5mm thick glass with necessary rubber beading gasket etc complete all as specified and directed by Engineer-in-Charge. |
| 20 | S & F for Anodised aluminium grill (anodised transparent or dyed to required shade according to IS 1868 with minimum anodic coating of grade AC 15) of approved design/pattern, with approved standard section and fixed to the existing window frame with CP brass/stainless steel screws @ 200mm centre to centre including cutting the grill to proper opening size for fixing and operation of handles and fixing approved anodised aluminium standard section around the opening complete all as specified and directed by Engineer-in-Charge. |
| 21 | S & F mild steel work in hollow square/rectangular trusses including special shaped washer etc. complete using ERW or induction butt welded tubes conforming to I.S. 4923 -1997 (Reaffirmed 2009) grade Yst.-310 complete all as specified and directed by Engineer-in-Charge. |
| 22 | S&F roof trusses (framed), trussed, purlins, crane gantries, rails and fastenings and heavy bracket framing (Beam, tee, angle, channel or flat sections) including distance pieces, cleats etc complete all as specified and directed by Engineer-in-Charge. |
| 23 | S & F plates (plain or chequered) channels, square cut or notched (ordinary and counter sunk) forming holes, without any attachment cofirming to Fe 410 -W (Gde- E- 250) quality-A complete all as specified and directed by Engineer-in-Charge. |
| 24 | S&F Mild steel screw bolts (machine made) with hexagonal or square heads at one end and screwed the other, or screwed both ends, each screwed end to be fitted with washers and one hexagonal or square nut, longbut length of bolt exc 5cm but n exc 10cm long complete all as specified and directed by Engineer-in-Charge. |
| 25 | M&L for pre-painted hot dip aluminium-zinc alloy metallic coated corrugated steel sheet, any pattern corresponding to IS15965:2012 of durability class 3, atmospheric classification category 3, coating class AZ 150, 0.50mm thick of an approved colour and having yield strength of 550 MPa as in roof covering fixed with self tapping screws as specified including necessary scaffolding and safety measures at any floor complete all as specified and directed by Engineer-in-Charge. |
| 26 | M&L for hot dip aluminium-zinc alloy metallic coated plain steel sheet as per IS 15965:2012 of durability class 3, atmospheric classification category 3, coating class AZ 150, 0.50mm thick of an approved colour and having yield strength of 550MPa as in ridge/valley/gutter/eaves boardings fixed with self tapping screws as specified including necessary scaffolding and safety measures at any floor complete all as specified and directed by Engineer-in-Charge. |
| 27 | M&L for 75 mm thick Cement concrete type C-2, 1:3:6 (using 40 mm graded crushed stone aggregates) as in plinth protection etc, finishing cement concrete surface even and smooth with out using extra cement including making joints with hot bitumastic mix in proportion of bitumen and sand 1:2 complete as specified & directed. |
| 28 | M& L for PCC 1:3:6 type C1 (using 20 mm graded crushed stone aggregate) as in sub base floor complete all as specified and directed by Engineer-in-Charge. |
| 29 | M&L for preparing new wood & wood based surfaces of any description, not otherwise described, over 10 cm width or girth and applying two coats of synthetic enamel paint over a coat of pink primer complete all as specified and directed by Engineer-in-Charge. |
| 30 | M&L for preparation of new or previously steel surfaces of any description, over 10 cm width or girth, not otherwise described and evenly applying two coats of synthetic enamel paint over a coat of red oxide primer complete all as specified and directed by Engineer-in-Charge. |
| 31 | M&L plain,solid straight chowkats and frames wrought, framed rebated on the solid rounded or chamfered, put togather with glue pinned at joints suplied and fixed with iron frame complete all as specified and directed by Engineer-in-Charge. |
| 32 | Taking up or down steel water tubing of bore 15mm dia and connections, including cleaning for refixing or removal to store complete all as specified and directed by Engineer-in-Charge. |
| 33 | Taking up or down steel water tubing of bore of pipes 20mm dia. and connections, including cleaning for refixing or removal to store complete all as specified and directed by Engineer-in-Charge. |
| 34 | S&F 20mm bore GI pipes medium grade with all fittings complete to walls and ceiling or laid in floors complete all as specified and directed by Engineer-in-Charge. |
| 35 | S&F 15mm bore GI pipes medium grade with all fittings complete to walls and ceiling or laid in floors complete all as specified and directed by Engineer-in-Charge. |
| 36 | M&L for roughening surfaces of old concrete floor by picking, sweeping clean and washing down with water to remove dust etc and brushing neat cement slurry with 3.0kg of cement per sqm metre complete all as specified and directed by Engineer-in-Charge. |
| 37 | M&L for coloured non skid joint free ceramic tiles of 7mm to 8mm thick (squire / rectangular) area of each tile exceeding 0.18 Sqm but not exceeding 0.38 sqm in floors, etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match including 15mm thick screed bed in cement mortar 1:6 for laying floor finishes complete all as specified and directed by Engineer-in-Charge. |
| 38 | Dismantling of wall and ceiling boards (fiber, pulp, insulation etc.) or insulation boards/slabs/blankets, any thickness, including frames and cover fillets complete all as specified and directed by Engineer-in-Charge. |
| 39 | Supply and fixing inter locking metal grid (snap grid for false ceiling) of size 605mm x 605mm in true horizonatal level, hot dipped galvanised steel sections consisting of main “T” runner with suitably spaced joints to get required length and size 24mm x 38mm made from 0.30mm thick (Min) sheet spaced at 1200mm centre to centre and cross “T” of size 24mm x 28mm made of 0.30mm thick (Min) sheet, 1200mm long spaced between main “T” at 600mm centre to centre to form a grid of 1200mm x 600mm and secondary cross “T” of length 600mm and size 24mm x 28mm made of 0.30mm thick (Min) sheet to be interlocked at middle of the 1200mm x 600mm panel to form grids of 600mm x 600mm and wall angle of size 24mm x 24mm x 0.4mm. Main “T” runner to be suspended from purlins or truss member using 2 to 3 mm dia GI wire, 1200mm x 600mm centre to centre all complete for all heights as per specifications complete all as specified and directed by Engineer-in-Charge. |
| 40 | M & L for 4 mm thick high pressure, oceanic pre-primed, self embossed, non asbestos fibre cement decorative board, water, termite and fire resistant for insulation ad acoustic purpose to be placed in grid system hold down clips with provision of high fixtures, air conditioning, diffuser and ducts, sprinkler, smoke detector etc, complete all as per manufacturer instructions complete all as specified and directed by Engineer-in-Charge. |
| 41 | S&F in repair fancy type 15mm dia Bib taps cast copper alloy, chromium plated screwed down to iron pipe or for brass ferrule & fixed complete all as specified and directed by Engineer-in-Charge. |
| 42 | S&F in repair fancy type 15mm dia pillar taps, cast copper alloy with capstan heads, chromium plated , screwed down high pressure, with or without lettered 'Hot' or 'Cold' with long screwed shanks & fly nuts, screwed for iron pipe & fixed complete all as specified and directed by Engineer-in-Charge. |
| 43 | S&F in repair vitreous china wash down water closet, \\"padestal pattern, white( Including fixing bolts and plastic water closet seat , black closet patternwith flat bottm and cover and mild steel chromium plate and aluminium hinges device. (excluding flushing cistern and flush pipe) complete all as specified and directed by Engineer-in-Charge. |
| 44 | S&F Wash basins white, vitreous China, flat back, size 580x450mm, excluding taps, waste, chain and plug and porcelain stopper but including brackets fixed to wall complete all as specified and directed by Engineer-in-Charge. |
| 45 | S&F PVC High/Low level flushing cistern 10 litres capacity including all fittings i.e float valve, syphon, flush pipe, brackets complete all as specified and directed by Engineer-in-Charge. |
| 46 | S&F PVC (SWR) pipes 110mm dia single socketed, in any length with rubber ring joints, laid in trenches or in floors complete all as specified and directed by Engineer-in-Charge. |
| 47 | S&F PVC (SWR) pipes 75mm dia single socketed, in any length with rubber ring joints, laid in trenches or in floors complete all as specified and directed by Engineer-in-Charge. |
| 48 | S&F PVC (SWR) bends 110mm dia any radius as in repair complete all as specified and directed by Engineer-in-Charge. |
| 49 | S&F 75mm dia PVC (SWR) bends any radius as in repair complete all as specified and directed by Engineer-in-Charge. |
| 50 | S&F in repair PVC connection 15mm size with PTMT nuts of length 600mm complete all as specified and directed by Engineer-in-Charge. |
| 51 | S&F in repair 15mm bore dia stop valves / angle valves, cast copper alloy, fancy type, chromium plated, screwed down, high pressure, with crutch or butterfly handle, screwed both ends for iron pipe or for unions and fixed complete all as specified and directed by Engineer-in-Charge. |
| 52 | M&L 75mm dia PVC (SWR) floor trap/nahani trap, plain with grating including jointing with solvent cement in repair complete all as specified and directed by Engineer-in-Charge. |
| 53 | S&F in repair 600mm x 450mm beveled edge mirror of selected quality glass, mounted on 6mm thick AC building board or commercial plywood and fixed to wooden plugs with chromium plated brass screws and cup washers fixed complete all as specified and directed by Engineer-in-Charge. |
| 54 | S&F in repairs shower rose, chromium plated brass, fancy type, 125 mm with or without swivel joint, any size, including fixing to steel pipe or union, complete all as specified and directed by Engineer-in-Charge.. |
| 55 | S&F soap dish of stainless steel fixed to wall with chromium plated brass screws fixed in repair complete all as specified and directed by Engineer-in-Charge. |
| 56 | S&F in repair curtain rods, anodised aluminium alloy, chromium plated with fixing brackets, stops, rollers etc complete all as specified and directed by Engineer-in-Charge. |
| 57 | M&L for preparation of old surfaces of wall and preparing surfaces as directed by finally applying two coats of distemper oil emulsion complete all as specified and directed by Engineer-in-Charge. |
| 58 | M&L for preparation of old surfaces of wall and preparing surfaces as directed and applying two coats of cement base complete all as specified and directed by Engineer-in-Charge. |
| 59 | Dismentling floor, hearth or wall tiling including cement mortar bedding (but not backing), removing seviceable tiles to store and rubbish off the premisses complete all as specified and directed by Engineer-in-Charge. |
| 60 | M&L for coloured non skid joint free ceramic tiles of 7mm to 8mm thick area of each tile not exceeding 0.11 Sqm in floors, etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match including 15mm thick screed bed or bedding layer in cement mortar 1:6 for laying floor finishes complete all as specified and directed by Engineer-in-Charge.. |
| 61 | S & F in repair health faucet fining in pipe complete with (ABS body ) mild steel chromimum plated suitable for 15mm dia pipe with 1.25 metre long flexible tube and ABS wall hook including connection and fixed in position complete all as specified and directed by Engineer-in-Charge. |
| 62 | Taking down aluminium point wiring (light, fan, socket or power) complete, including fixture and fittings such as switches, ceiling roses, pendants, regulators, sockets, light fitting etc.removing materials to store for keeping in safe custody or for taking credit (credit for above items should be made as per conditions separately) and making good disturbed surfaces of walls, floors, etc complete all as specified and directed by Engineer-in-Charge. Please Enable Macros to View BoQ information |
| 63 | Taking down aluminium point wiring (light, fan, socket or power) complete, including fixture and fittings such as switches, ceiling roses, pendants, regulators, sockets, light fitting etc.removing materials to store for keeping in safe custody or for taking credit (credit for above items should be made as per conditions separately) and making good disturbed surfaces of walls, floors, etc complete all as specified and directed by Engineer-in-Charge. Please Enable Macros to View BoQ information |
AI Tender Summary
Tender Timeline
Jul 04, 2026
11:30 IST
Tender Published
Tender notice published.
CompletedJul 25, 2026
17:00 IST
Bid Submission Deadline
Online submission via eProcurement portal.
Upcoming · 18 daysAug 01, 2026
Bid Opening Date
Technical bids will be opened and evaluated.
Upcoming · 25 daysTender Documents
Download All (ZIP) ↓
Disclaimer
We takes all possible care for accurate & authentic tender information. However users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender