Tender for Tender for Supply Of Fire Fighting Equipments For Use In The Fire Brigade Of Udaipur Municipal Corporation On Annual Rate Contract. (E_01 / Fire_01)
Tender Value
45 Lakhs
Estimated cost
Bid Submission
13 Jul 2026
6 days left
EMD
90000
Bank guarantee accepted
Document Fee
5900
Non-refundable
Tender Type
Online
Tender Overview
Organization
Tender ID
Competition Type
NCB
Bidding Type
Tender
Location / State
Udaipur → Rajasthan
EMD Exemption
Not Available
Quantity
Not Available
Website
Contact Person
Address
Project Description
Tender for Supply Of Fire Fighting Equipments For Use In The Fire Brigade Of Udaipur Municipal Corporation On Annual Rate Contract. (E_01 / Fire_01)
BOQ
| Sl. No. | Item Description |
| 1 | Providing Gum Boot Technical Specification Product: Electrical Insulating Fireman BootSize range Euro: 36 – 50 , UK: 3½ - 14½ US: 4½ - 15½Type of construction : Vulcanized Rubber Upper and Sole /Coated steel toe cap.Recommendation : Structural fire fighting, General fire rescue, Bush fire fighting European Standard CE Approved suitable for fire rescue, fire suppression, property conservation & etc.High Electrical Resistance Outsole, Heat Insulation, Cold Insulation Slip Resistance on ceramic tile with Sodium Lauryl Sulphate, Fuel Oil Resistant Outsole, Heel Energy Absorption, Nail Penetration Resistance, Toe Protection, Resistant to hot contactToe protection, Compression resistance, Nail penetration resistance, 18 kV Electric Shock Resistance protectionLining Material : Extra comfort with woven cotton canvasUpper construction : Flame retardant upper with heat insulation WaterproofReinforced rubber , High visibility with black and yellow contrastSole / Heel : Flame retardant rubber outsoleFuel oil resistant sole suitable for inimical environmentSlip resistant vulcanized rubber outsole Excellent abrasion resistant for extra durabilityHeel energy absorption design to minimize heel impactCatered to enter high temperatureCold insulation sole constructionSlip Resistance Performance Twice That Required By EN 13287 SRA And SATRA TM144 StandardsResistance To Hot Contact 60 Seconds 300°CSteel Toe Cap : Epoxy coated toe caps for anti-corrosion Meets impact and compression testsMetal toecap provides reliable protection in cold & hot environmentsSteel MidsoleNon-corrosive stainless steelWithstands pin & sharp objectsChemical Resistance : Sole & Upper - Resistant towards strong acids and alkaliFinishing : Lacquer coating for weather protection Prefered make :- Novex, Udhyogi or equivalent |
| 2 | HelmateNew, modern design and excellent protection properties. Optimal relationship between protection and comfort with a broad spectrum of optional upgrades. Structural firefighting has never been safer.PERFORMANCEExtreme temperature resistance(up to 1,000°C in a 10 second flash over flames)Long-term temperature resistance (radiant heat test 14 kW/m2)High resistance to mechanical impacts Low-temperature classification -30°C SAFETYElectrical insulation capacity head protection (including neck and face) Interior shock absorber.Reflective elements for better visibility in low-light conditionsNeck protector (available in aluminised fi bre, Nomex, genuine leather or wool for Holland style)3 point chinstrap (tested to prevent skin irritation, fire retardant aramid tape) Chemical resistanceCOMFORTLightweightIntegrated adjustment systemOne shell size for head sizes from 52 to 64 cm Wide range of accessories and high level of personalisationHIGH TECH MATERIALSFlame retardant and high temperature resistant composite Anti-scratch and anti-fog coated integrated visor Anti-se :- Hicare, Karam or equivalentFiremen HelmetThe Fireman Helmet Light Weight 1400 Gms Helmet Having Flame Retardant Shell With Reflective And Luminescent Stripes |
| 3 | Self-Contained Breathing Apparatus1. General Requirement:The Self-Contained Open Circuit Type Compressed Air Breathing Apparatus Set With Spare Cylinder Confirming IS 102452. Back Plate (Body Harness):.The Ba Set Back Plate Of Should Be Ergonomically Designed And Flexible.The Ba Set Back Plate: Should Be Adjustable Type ( To Extend Back Plate Height As And When Required )The Ba Set Back Plate Harness Padded And Made Of Flame Retardant MaterialThe Hoses Channeled Within The Back Plate To Prevent Snag HazardThe Cylinder Strap Shall Be Made Up Of Flame Retardant Material With Velcro And Which Can Be Adjusted To Accommodate AllStandard Cylinders.All Securing Buckles Shall Be Designed In Such A Way For Accessibility And Easy Handling With Gloved Hands Without CompromisingSecurity.* The Back Plate Should Be Analog And Digital Pressure Gauge At One Side To Indicate Pressure Of The Cylinder And The Other Side The Breathing Air Hose Quick Fit Coupling, Through Which Demand Valve Is Inter ConnectedThe Ba Set Back Plate Should Be Breathing Air Hose Design With Quick Fit Coupling, It Option To Interconnect \\"y\\" Piece CouplingFor Second Line Rescue With Demand Value And Face Mask In An Emergency.3. Facemask:The Face Mask Shall Be Of Positive Pressure TypeIt Should Be 5 Point Head Harness Made Of Kevlar / RubberIt Should Be In Built Communication System, With A Radio Jack To Connect Walkie-Talkie.It Should Be Also The Facility Of Push To Talk With A Button.It Should Be Integrated With In Built Amplifier For Excellent Communication And Distress Alarm.It Should Be 2 Led And It Blink, If Distress Alarm Is Activated.The Facemask Shall Feature A Full Mask Assembly Shall Be With Reverted Edge Seal And Made Of Soft Skin Friendly Silicone MaterialWith Flame Resistance RequirementVisor Shall Be Of Multi Curvature Type And Provide Wide-Angle Vision With More Than 85% Field Of Vision And Be Made OfReplaceable Scratch And Heat-Resistant Hard Coated Polycarbonate Material.Visor Shall Be Self-Demisting Type Through Special Control Of Inspired AirIt Integral Inner Mask Shall Reduce Dead-Space And Co2 Build Up And Eliminate Misting Of Visor. |
| 4 | High led search light Range up to 1 kmMATERIALThe body is made of highstrength but light weight ABC plastic, lending it rigidity and toughness even in situations of rough handling. Whatever the situation, you can laways bank on this solidly built, rain-proof FOS LED Search Light.LED POWERFeaturing a high power55W branded LED coupled with a big parabolicreflector, this FOS rechargeable torch offers unmatched luminosity of up to 1800 lumens with a focesed beam range visibility of up to 2 kms.BATTERY POWERPowering the LED is a high-performance 8000 mAh, 7.4V Lithium-ion battery which offers a battery backup of up to 9 hours. The package comes with 2 battery chargers, an AC Wall Charging Adapter and a Car Charging Adapter, both with 9 V-1 Amp. Output.LIGHT MODESThis heavy duty ewchargeable handheld torch comes with 2 light brightness modes, i.e. super strong and strong, which can be used as per your lighting needs.User ApplicationHeavy duty outdoor ultra-long-range lighting applications as commercial search operations for Armed Forces, Industries, Security Agencies. Preferred make :- DETECH, FOS or equivalent. |
| 5 | Multi Purpose Branch / Select flow nozzle Whight : 4.3 kg approxConnection-21/2\\",2\\", 11/4\\"Application-FIRE FIGHTINGMaterial-Aluminum, Alloy, Stainless Steel Size-63mm, 40mm, 50mmFlow- 600LPM, 800LPM,900LPM, 1200LPMWorking Pressure 5 to 12KG/CM2Hydrulic Test- 30KGInlet Connections- 63MM, 40MM, 50MM Prefered make : - Newage, Onspot or equivalent |
| 6 | Lower Pressure ApplicatorInlet -Pipe - Aluminum AlloyNozzle - Brass Extruded RodSize - 63 mm Male instantaneous inletTest Pressure - 21 BarWorking Pressure - 7 BarDischarge Pattern - Water Curtain PatternFlow Rate - 130 LPM @ 7 BarDischarge Range - Throw Range: 7 m MinimumFinish - Natural SS Finish Polished Prefered make :- Newage, Onspot or equivalent |
| 7 | Fire Resistant Dangries* 100% COTTON Fire Retardant Premium Fabric in 230 GSMadhering to ISO 11612:2015 A1 and A2.* 2 Front pockets with Quality Ring Buttons, 2 side pockets, 1 tool pocket, 1 sleeve pocket and 2 back pockets.* For high visibility, 2 inch Fire retardant 3M reflective tapes have been stitched on the shoulder, sleeves and on the knees.* Fire retardant YKK zippers front closure, ring buttons on sleeves for closure All the stress points have been bartacked.* The size is as per actual and gives a smart fit look however if you need a lose fit or if worn above work clothes then go 1 size bigger.FABRIC SPECIFICATION- Premium 100% Cotton per-shrunk Fire retardant premium Fabric in 230 GSM adhering to ISO 11612:2015 A1 and A2. Size M,L,XL, XXL Prefered make :- French terrain, safe wear or equivalent |
| 8 | Fire Proximity Suit Coat/Jecket1. General Description: Coat with a high central zip closure, covered with suitable storm flap. The coat should have full-length sleeves and a stand up collar with adjustable throat tab.2. Standard: The coat must meet the NFPA 1971:2007 or3. Construction a. The coat should have a three-layer construction: b. Outer Cloth: The outer shell fabric should be made from inherently flame resistant fiber with requisite blend of antistatic fibers. The colour of the outer shell be Dark Navy Shade.c. Moisture Barrier: MoistureBarrier shall be Fire resistant andbreathable in nature. The construction should be micro porous in nature like non wovensubstrate / felt / PU / spun lace aramid – suitably laminated with PTFE / PU like membrane or treated with compound to ensure that no water ingress from outside besides allowing perspiration and heat to escape from inside.d. Thermal Barrier: The Thermal Barrier should consist of two integrated or quilted layers. The innermost layer facing the Moisture Barrier should be made from inherently flame resistant fibres in non wiven felt / corded lane construction.e. The should be detachable i.e., it should be able to be used as a single layered Coat or multiple layered Garment and should be detachable by buttons from inside.f. Seams: All sewing to be done using para-aramid or equivalent strong inherently FR thread. The seams on the outer layer should be stitched with strong thread overlock.g. Pockets: Coat should be provided with 3 pockets as standard. 2 waist pockets on the lower fronts with flap closure and 1 patch pocket inside the coat.h. Collar: The collar of the Coat should be designed so that the neck portion is doubley secured and covered by means of a throat tab, fitted with fire retardant Velcro for secure fastening across the neck. A hanger loop, centrally placed on outer collar or inside section to be provided to facilitate hanging.i. Front Closure The coat should have a heavy-duty moulded zip beneath a full length catch flap, closing with fire retardant Velcro.j. Sleevs & Cuffs: The sleeve should be designed to have an additional gusset (all 3 layers) in the underarm or any other design innovation to allow the arms to move freely without raising the hem of the coat. An aramid rib-knitted internal cuff to be provided for suitable wrist protection.k. Reflective Tape: The Coat should have a high quality reflective tape provided at the following places. - Single row 50 mm width, around hem / waist (including across front flap) - Single row 50 mm width,around lower sleeves The tape should be premium quality and the quality should comply with the length and test parameters stipulated in the corresponding NFPA /En standreds. I. Sizing: Size chart should be provided along-with the offer. The size should be suitable for fitting on person of 5'10\\" & 5' 8\\" height.m. Labels: A large clear label should be permanently attached (sealed) or stitched inside the lining of the fire suit. This label should give full details of compliance to international standards, manufacturers' contact details, sizing, wash/care information, style and date of manufacture and traceability coding. Prefered make :- flare defend, safe wear, udhyogi or equivalent |
| 9 | ANTI FIRE HOODSSTANDARDS: Certified to NFPA 1971FEATURES: The Hood should be offThe face opening should be Fit and Flat The Neck Protector should be fit and properly covering theThe Hood should be double layered having each layer of the Fabric of about 230 GSM, inset collar and face opening with elastic. Prefered make :-flare defend, safe wear, udhyogi or equivalent. |
| 10 | Fire Entry Suit1 Aluminized fire entry suit containing coat (flame seal) with pants, having hood for thermal protection with gold plated tempered glass layers, overall gloves, flame retardant shoes/boots and a back pouch for wearing breathing apparatus set.2 Size- medium3 Made from Z-Flex (NFPA 701/UL 214 certified) & Zetex fabrics.4 Other specifications: material: 8 layers construction includes: aluminized Z-Flex outer shell, Z-Sil, 1-inch fiber-glass insulation,aluminized vapour barrier, zetex plus, 1- inch fiber glass insulation, aluminized vapor barrier, flame-resistant cotton lining. (i). Temperature rating: short duration ambient heat of1500 F (815 C, total flame of 2000 F (1093 C), Radiant heat to 3000 f (1650 C) for 3000 series.5 (Hood, coat, pants, boots) construction1. Hood: Designed for use with an air mask. Built-in shell for structural support. Inner drape seals and underarm adjustment straps Ratchet-adjustable hard cap with speedy clip for support Hardened aluminum window frame with two gold-plated tempered glass lenses backed by two additional lenses for thermal protection.2. Coat: double storm fly front. Flame seal with drawstring at coat bottom.3. Pants: high waist with 2\\" wide adjustable suspends and adjustment straps on leg bottoms.4. Boots: designed to fit over work shoes. Rear entry with overlap snap enclose and adjustable take-up straps. Boot sole made from 2\\" of layered insulation, flame retardant cotton lining, aluminum foil, and wire-reinforced, flame-retired neoprene fiber glass.5. Mitts: heavy construction; made with zetex plus fabric. Aluminized outer layer.Certification: EN 532-1992 limited flame spread, EN 367:1992 convective heat, EN 366:1993 method B radiant heat, EN 407:2004 molten metal splash.Technical Approval: The Bidder Should Be Submit Product Data Sheet And Valid Certificate At The Time Of Tender Submission.If The Bidder Firm Is Manufacturer Then Firm Has To Submit The Valid Registration Certificate. If The Bidder Firm Is Not TheManufacturer Then Firm Has To Submit The Valid Manufacturer's Authorization Certificate For This Particular Tender. The Bidder Shall Conduct A Successful Demonstration Of The Quoted Product Explaining All The Features Detailed In The Above Point Wise Specification, Failing To Provide A Successful Technical Demonstration The Bid Would Be Technically Rejected.Guarantee And Training Guarantee Minimum 1 Year Without Any Manufacturing Defects From Date Of Receipt Material Free Of Cost Training & Service For The 1 Year At Our Site.Operation And Maintenance Manual: The Manufacturer Supply Operation And Maintenance Manual With Each Set Along With Supply. |
| 11 | HAZMAT SUITHazmat Suit Prefered make :- flare defend, safe wear, udhyogi or equivalent. Lightweight twin-layer barrier: Excellent chemical resistance*Yellow color: Enhanced visibility, for improved workplace safetyEnhanced features: Large SCBA hump, integral sock, passthrough and CEJN connectorProtection against Chemical warfare agents: Breakthrough time > 48 Hours for Seven warfare agents |
| 12 | FOAM MAKING BRANCH: Supply of \\"AAAG\\" make AL. ALLOY FOAM MAKING BRANCH pipe of FB-20X as per IS.2097-suitable to discharge 900LPM@7Kg/cm² (suitable to induct AFFF-3%) (made of aluminum alloy construction) with SS-304 male inst. Inlet alongwith PVC pick-up tube with SS Strainer& DIP tube. |
| 13 | INLINE INDUCTOR (foam making) Prefered make :- Supply of \\"AAAG\\" makes INLINE INDUCTOR having 450LPM made of Aluminium Alloy (As per IS:617) construction with GUNMETAL (Grade LTB-2 of IS:318) 63mm inst. male/female inlet/outlet along with 25mm threaded connection for foam induction with 1- mtr length of PVC pick-up tube with Stainless steel Dip tube- Suitable for 3% of AFFF (Foam concentration) |
| 14 | HIGH EXPANSION FOAM GENERATOR:- Supply of \\"AAAG\\" make HIGH EXPANSION FOAM GENERATOR (MAXI) made of FRP BODY, with inline inductor, is a high expansion foam generation powered by Water turbine to produce large volume of expanding foam with minimum operation through to produce the foam expansion - ratio of-1:200 to 1:1000 (Open) and 1:475 to 1:700 (closed) with 63mm inst. Inlet through powered by water pressure alone, which drives a high efficiency water turbine coupled to an aerofoil. The generator comes with in-built flexible foam making net and inductor with PVC braided Pick-Up tube/hose and SS-304 dip tube.BODY FRPNOZZLES GUNMETALFOAM SCREEN STAINLESS STEELFAN STAINLESS STEELCOUPLINGS GUNMETAL |
| 15 | ADAPTORS Male to Male:-Supply of \\"AAAG\\" make GUNMETAL (Grade LTB-2 of IS :318) 63mm double male adaptor as per IS: 901 |
| 16 | ADAPTORS Female to Female:- Supply of \\"AAAG\\" make GUNMETAL (Grade LTB-2 of IS:318) 63mm inst. double female adaptor as per IS: 901 with double pull out type Lug assembly both the ends. |
| 17 | ADAPTORS Male to Female Prefered make:- Supply of \\"AAAG\\" make GUNMETAL (Grade LTB-2 of IS:318) Male to Female Adaptor having 63mm male threaded inlet and female threaded outletOnspot, New age, Aag or equivalent |
| 18 | FB5XMaterial - Barrel - AluminiumNozzle Assembly - Holding Ring - AluminiumInletMaterial - 63 mm InstantaneousRange -AAAG LXA5IS - 15 MetersInduction - 3%Pick up tube - Non-collapsible PVC Braided HoseWeight 3.5 kg approxWorking Pressure 3.2KG |
| 19 | FB10XMaterial - Barrel - AluminiumNozzle Assembly - Holding Ring - AluminiumInletMaterial - 63 mm InstantaneousRange -AAAG LXA5IS - 15 MetersInduction - 3%Pick up tube - Non-collapsible PVC Braided HoseWeight approx 6 kgWorking Pressure 5 to 10KG/CM2 |
| 20 | Hand Gloves Rubber Flock Lined Chemisafe 35 CMCode 662/14HSN 40159030Tax 18%Brand ChemisafeMaterial Made from latex rubber & flock linedSize 35 cm (14\\")Color OrangeWeight 140 gramsFeatures Soft & comfort with folk lineFactory Packing 100 PairsMOQ 10 PairsApproval CE EN 388 (1121)Application Suitable for acids, alkali & general industrial cleaning use.Availability Ready StockQuality Rating 5 Star |
| 21 | Ambu Bag With Accessories (Resuscitator) :-Material Made from high grade silicon & PVC. It includes peep valve, self inflating bag,air inlet and pressure release valve and oxygen reserve bagSize AdultColor Transparent milky whiteWeight 580GrmsApplication It is used to provide pressure ventilation to patient air or oxygen who are not breathing adequately. |
| 22 | Fireman Axe :-Material Valcanized rubber insulated handle and axe made from forged carban steeSize 440 mm lenth.Color Handle black, axe crome plated silver.Weight 1.45 KgFeatures Tested for 20000 volts, non slipgrip, bright finish handle. |
| 23 | Fire Fighting Hook With Wooden Stick:-Type Fire FightingMaterial Hook made from forged steel & wooden stickSize Length of hook 15\\" & with wooden sick 80 \\"Color RedFeatures Hook made from 25mmX5mm flate MS strip, one end of hook welded with 1\\" pipe, wooden stick can insert at other end of pipe.Application It is used specially firefighting for tearing down walls or ceiling. |
| 24 | Life Buoy Ring:-Weight: 2.5KGOutside Diameter: Not less than 72 cmInside Diameter: Not More than 43 CmOutside Material: HDPE PlasticInside Material: Rigid FoamColor: OrangeLifeline Rope: 10mm, White colorReflective Tape: 50mm W* 4 noShelf Life: 5 yearsStandard: SOLAS ApprovedBuoyance: 5N |
| 25 | Life Jacket :-PERSONAL FLOATATION DEVICEBUOYANCY-140NTYPE III PFDUSER AGE-18 TO 60 YEARSUSER WEIGHT ? UP TO 120 KGSWITH HEAD SUPPORTSTYLE - FREE SIZEWATER REPELLENT FABRIC100% PE FOAMQUICK RELEASE BUCKLESTANDARD BELTS FOR SECURE FITSHIGH VISIBILITY COLORIRS APPROVED NON-CLOG WHISTLECE CERTIFIED & SOLAS COMPLIANCES |
| 26 | Mobilize IBS501 Back board Stretcher:-PRODUCTSIZE :- 185X45X6cmSELFWEIGHT :- 8kg LOADLIMIT :- 159kgGROSSWEIGHT :- 10kgLIFTTYPE :- HorizontaMedical Device :- (93/42/EC)Class1 |
| 27 | Semi-Static Rope Type A, Climbing Rope 100 Mtrx 12 mm, Certifications such as IRATA Level 3, NOLS, or similar, UIAA 107, CE EN 1891:1998 TYPE ADiameter (mm) 12Rope Type AWeight per Meter (gms per meter) 91No. of Falls 14Static Elongation (%) 3,2% of Sheath 43Max Impact Force (kN) 5,6kNMaterial PolyamideSheath Slippage (mm) 0Breaking strength (Fig. 8 knot) 27 kN Construction 32 carrierKnotability 0.8 |
| 28 | Safety Net, ISI Marked Rope & as per IS 11057:1984 2 mm Double cord safety netMesh size: 40 mm X 40 mmRope material: PolypropyleneMesh rope: 2 mm diameter double cordBorder rope: 12 mm diameter PP ropeTie rope: 12 mm diameter PP rope of 2 meters length at every 1.5 meter intervalStandard: ISI marked, rope conforming to IS 5175 of 1992MESH SIZE 30MM X 30MM; MESH ROPE 2MM DOUBLE CORD; BORDER ROPE 12 MM; ISIMARKED POLYPROPYLENE ROPE (Size:10mtrx5mtr) Please Enable Macros to View BoQ information |
AI Tender Summary
Tender Timeline
Jul 04, 2026
11:30 IST
Tender Published
Tender notice published.
CompletedJul 13, 2026
17:00 IST
Bid Submission Deadline
Online submission via eProcurement portal.
Upcoming · 6 daysJul 14, 2026
Bid Opening Date
Technical bids will be opened and evaluated.
Upcoming · 7 daysTender Documents
Download All (ZIP) ↓
Disclaimer
We takes all possible care for accurate & authentic tender information. However users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender