Tender For Special Repair To Certain Electrical Eqpt, Ac Duct And Rewiring In Certain Building At 54 Asp Under Ge (Af) Gurgaon No. 1
Tender Value
73.99 Lakhs
Estimated cost
Bid Submission
01 Aug 2026
21 days left
EMD
1.36 Lakhs
Bank guarantee accepted
Document Fee
1000
Non-refundable
Tender Type
Online
Tender Overview
Organization
Tender ID
Competition Type
NCB
Bidding Type
Tender
Location / State
Gurgaon → Haryana
EMD Exemption
Available
Quantity
Not Available
Website
Contact Person
Address
Project Description
Tender for Special Repair To Certain Electrical Eqpt, Ac Duct And Rewiring In Certain Building At 54 Asp Under Ge (Af) Gurgaon No. 1
BOQ
| Sl. No. | Item Description |
| 1 | Supply, install, testing and commissioning of Eco friendly Generating Set Diesel Engine driven of capacity 75 KVA/ 60 KW at 0.8 PF or nearest higher size 415 volts AC, 3 phase, 50 Hz 4 wire, directly coupled alternator and engine, water cooled common base platform with inbuilt fuel tank and including all excavation, PCC foundation, anti vibration pads/dampers as per manufacturer instructions and as directed by manufacturer. The DG set shall work at ambient conditions of Gurgaon and produce specified out put.The derating factors, if any, shall be taken in to consideration while arriving the capacity to give specified out put. The DG set shall be factory assembled by the OEM of the engine manufacturer and all components shall be accommodated in enclosure and other accessories comprising of the following:-(A) Engine : Eco friendly emmision limits for diesel engines as per CQAM Direction No. 76 letter folio No. A-11018/01/ 2021-CQAM/ 15322-15331 Dated: 29.09.2O23 government of India and noise level (CPCB - IV norms compliances) diesel Engine confirming to BS/IS standard, confirming to BS:5514/DN-6271 / IS 10002/ISO-3046, of suitable BHP as per the standard design of OEM to run the DG set in full load / 110% overload with out any change of out put parameters, (not less than 608 BHP),1500 RPM, water cooled complete under NTP condition, with a provision for 10% over load for one hour on 12 hours continuous running. (B) Alternator : Synchronous alternator 75 KVA, 1500 RPM, 415 Volts, 50 Hz, 3 phase system self excited, self regulated, self ventilated in brushless design provided with suitable automatic voltage regulator with ± 1% all load between no load to full load and power factor 0.8 to unity with 10% overload capacity for one hour in any 12 hours of operation without exceeding temp rise limit, Confirming to BS:5000/IS 4722 with standard design with IP 23 protection and class of \\"H\\" insulation & having surge separator for protection of alternator for reverse supply. (C) Acoustic enclosure : Acoustic enclosure drip proof & screen protected meeting stringent MOEF/CPCB norms of 75 dBA @ 1 mtr at 75% load under free field conditions with air inlet louvers powder coated. (D) AMF panel : Supply, install, testing and commissioning of AMF panel indoor type suitable for 75 KVA DG set, totally enclosed with sheet metal enclosure with sheet (CRCA) duly powder coated, dust & vermin proof made out of min 2.0 mm thick sheet |
| 2 | Supply, install, testing and commissioning of Eco friendly Generating Set Diesel Engine driven of capacity 20 KVA/ 16 KW at 0.8 PF or nearest higher size 415 volts AC, 3 phase, 50 Hz 4 wire, directly coupled alternator and engine, water cooled common base platform with inbuilt fuel tank and including all excavation, PCC foundation, anti vibration pads/dampers as per manufacturer instructions and as directed by manufacturer. The DG set shall work at ambient conditions of Gurgaon and produce specified out put.The derating factors, if any, shall be taken in to consideration while arriving the capacity to give specified out put. The DG set shall be factory assembled by the OEM of the engine manufacturer and all components shall be accommodated in enclosure and other accessories comprising of the following:-(A) Engine : Eco friendly emmision limits for diesel engines as per CQAM Direction No. 76 letter folio No. A-11018/01/ 2021-CQAM/ 15322-15331 Dated: 29.09.2O23 government of India and noise level (CPCB - IV norms compliances) diesel Engine confirming to BS/IS standard, confirming to BS:5514/DN-6271 / IS 10002/ISO-3046, of suitable BHP as per the standard design of OEM to run the DG set in full load / 110% overload with out any change of out put parameters, (not less than 608 BHP),1500 RPM, water cooled complete under NTP condition, with a provision for 10% over load for one hour on 12 hours continuous running.(B) Alternator : Synchronous alternator 20 KVA, 1500 RPM, 415 Volts, 50 Hz, 3 phase system self excited, self regulated, self ventilated in brushless design provided with suitable automatic voltage regulator with ± 1% all load between no load to full load and power factor 0.8 to unity with 10% overload capacity for one hour in any 12 hours of operation without exceeding temp rise limit, Confirming to BS:5000/IS 4722 with standard design with IP 23 protection and class of \\"H\\" insulation & having surge separator for protection of alternator for reverse supply.(C) Acoustic enclosure : Acoustic enclosure drip proof & screen protected meeting stringent MOEF/CPCB norms of 75 dBA @ 1 mtr at 75% load under free field conditions with air inlet louvers powder coated. (D) AMF panel : Supply, install, testing and commissioning of AMF panel indoor type suitable for 20 KVA DG set, totally enclosed with sheet metal enclosure with sheet (CRCA) duly powder coated, dust & vermin proof made out of min 2.0 mm thick sheet |
| 3 | Supply installation testing and commissioning of Voltage stablizer for automatic operation three phase naturally oil cooled (ONAN) outdoor type & designed for input variation between 300 V to 480 V with out put voltage stablized at 415V with accuracy of ± 1% and speed correction 8 Volts per second and capacity of 200 KVA as per IS 9815/IS 2026. Class `H' insulation with digital temperature/ voltage /current display overload for 100% unbalance etc all as specified and directed including short circuit , high voltage trips protection single phase preventor, low voltage trip auto visual alarm and surge spike suppress and porcelain bushing (conforming to IS 3347) along with cable junction boxes with top or side entry and independent phase contropl etc complete with first fill of transformer oil all as specified and as directed. |
| 4 | All as per item No - 3.00 here in before but of capacity 300 KVA. |
| 5 | All as per item No - 3.00 here in before but of capacity 400 KVA. |
| 6 | All as per item No - 3.00 here in before but of capacity 50 KVA. |
| 7 | All as per item No - 3.00 here in before but of capacity 75 KVA. |
| 8 | Supplying, installing, testing and commissioning of submersible pumping set suitable for 200/250mm bore well with submersible motor 3 phase 415 volts, 2.24 KW ( 3.0 HP) coupled with pump 5-79 meter head, discharge 70 - 300 LPM suitable for 200 mm boring complete all as specified and directed. Note: (i) The length of submersible cable connected alongwith motor supplied by manufacturer shall not be measured and paid for separately. Make :- Kirloskar (b) KSB (c) Wilo Mather (d) M/s Jyoti or techno-commercially equivalent as per list of make in PS. |
| 9 | Supplying, installing, testing and commissioning of submersible pumping set suitable for 200/250mm bore well with submersible motor 3 phase 415 volts, 5.6 KW ( 7.5 HP) coupled with pump 55-140 meter head, discharge 150-330 LPM suitable for 200 mm boring complete all as specified and directed.Note: (i) The length of submersible cable connected alongwith motor supplied by manufacturer shall not be measured and paid for separately.Make :- Kirloskar (b) KSB (c) Wilo Mather (d) M/s Jyoti or techno-commercially equivalent as per list of make in PS |
| 10 | Supplying, installing, testing and commissioning of submersible pumping set suitable for 200/250mm bore well with submersible motor 3 phase 415 volts, 7.46 KW (10 HP) coupled with pump 65-170 meter head, discharge 150-330 LPM suitable for 200 mm boring complete all as specified and directed.Note: (i) The length of submersible cable connected alongwith motor supplied by manufacturer shall not be measured and paid for separately.Make :- Kirloskar (b) KSB (c) Wilo Mather (d) M/s Jyoti or techno-commercially equivalent as per list of make in PS |
| 11 | Supplying, installing, testing and commissioning of submersible pumping set suitable for 200/250mm bore well with submersible motor 3 phase 415 volts, 9.33 KW (12.5 HP) coupled with pump 80- 205 meter head, discharge 150-330 LPM suitable for 200 mm boring complete all as specified and directed.Note: (i) The length of submersible cable connected alongwith motor supplied by manufacturer shall not be measured and paid for separately. Make :- Kirloskar (b) KSB (c) Wilo Mather (d) M/s Jyoti or techno-commercially equivalent as per list of make in PS |
| 12 | Supplying, installing, testing and commissioning of submersible pumping set suitable for 200/250mm bore well with submersible motor 3 phase 415 volts, 11.19 KW (15 HP) coupled with pump 42- 205 meter head, discharge 180-390 LPM suitable for 200 mm boring complete all as specified and directed.Note: (i) The length of submersible cable connected alongwith motor supplied by manufacturer shall not be measured and paid for separately. Make :- Kirloskar (b) KSB (c) Wilo Mather (d) M/s Jyoti or techno-commercially equivalent as per list of make in PS |
| 13 | Supplying, installing, testing and commissioning of centrifugal pumping set coupled on common base frame with induction motor 3 phase 415 volts, 9.33 KW (12.5 HP) coupled with pump 42- 205 meter head, discharge 180-390 LPM suitable for 200 mm boring complete all as specified and directed.Note: (i) Necessary civil work viz. foundation for placement of pump and pump accessories shall be covered in the scope of work. Make :- (a) Kirloskar (b) Beacon (c) CRI (d) Crompton (e) KSB or techno-commercially equivalent as per list of make in PS |
| 14 | Supply, installation, testing and commissioning of Monoblock type centrifugal pump of Capacity 15 HP, having Discharge 7.5 LPS water flow and 20 MWC head suitable for 3X75 TR Central AC Plant along with elastomeric insulation, self-priming, single-stage, centrifugal volute type pump having cast iron casing, enclosed type dynamically balanced phosphor-bronze/SS impeller, high tensile steel shaft, carbon steel stuffing box (sealed by mechanical seal), deep groove ball bearings, base plate, mounting channel frame, elastomeric insulation, accessories and fittings, viz. mechanical seal, pressure gauges, thermometers, drains, coupling, coupling guard, vibration isolation arrangement by means of spring / rubber type mounting and TEFC squirrel cage induction motor having IE- 3 efficiency and conforming to IS 12615: 2018 suitable for operation on 3- Phase, 415 V ± 10%, 50 Hz AC supply complete all as specified and directed. Make :- (a) Kirloskar (b) Beacon (c) CRI (d) Crompton (e) KSBNote : Necessary civil work viz. foundation for placement of pump and pump accessories shall be covered in the scope of work. |
| 15 | Supply, installation, testing and commissioning of pre-fabricated, galvanized steel sheet (G.S.S.) square/rectangular ducting for supply/return air with and including accoustic insulation as specified, fabricated from galvanized steel sheet, having zinc coating of 180 g/m² total on both sides complete with gaskets, elbows, splitters, vanes, supports etc. conforming to per IS 655:1963 along with required scaffolding work to install the ducts at site complete all as specified and directed.Note : Thermal insulation of duct will be measured under item No. 14.00. |
| 16 | 20 G (MS angle flanges) |
| 17 | Supply & Fix closed cell elastomeric nitrile rubber insulation with aluminum foil laminated on one side, having thermal conductivity not exceeding 0.037 W/mK at mean temperature of 20° C as per EN 12667, moisture diffusion resistance factor or ‘µ’ value of minimum 7,000 for base insulation material without the foil as per EN 12086, fire performance such that it passes Class 1 as per BS476 Part 7 for surface spread of flame and also fire performance of V0, HB as per UL 94, 1996, density without the foil between 40 to 55 kg/m³. The insulation material shall be FM (Factory Mutual) USA approved and dust & fibre free. The Aluminium foil shall be 60 microns thick and its weight shall be 193 gsm as per EN ISO 2286-2, tensile strength 90 N / 15 mm as per EN ISO 527-3 with elongation > 10% as per EN ISO 527-3 complete all as specified and directed. |
| 18 | 13 mm thick nitrile rubber polyvinyl nitrite rubber thermal insulation (for 20 guage duct) |
| 19 | Taking down copper/aluminium point wiring (light, fan, socket or power) complete, including fixture and fittings such as switches, ceiling roses, pendants, regulators, sockets, light fitting etc.removing materials to store for keeping in safe custody or for taking credit (credit for above items should be made as per conditions separately) and making good disturbed surfaces of walls, floors, etc. |
| 20 | Taking down carefully unserviceable DB any type/size disconnecting and making good disturbed surfaces complete all as directed |
| 21 | Taking down carefully unserviceable MCB SP/SPN/Isolator of any rating/size. |
| 22 | Material and labour Point wiring complete with 1.5 sqmm single core PVC insulated and unsheathed cable 1100 volts grade with multistranded copper conductor drawn through PVC concealed conduit fixed to walls / roofs / floors / ceiling etc. and including provision of 1.5 sqmm stranded copper conductor cable as earth continuity conductor and connected to common earth dolly, including fabricated steel terminal box made out of 1.60 mm thick MS sheet concealed in walls, suitable for housing the modular electrical accessories as switches, socket outlets, fan regulators etc., all as specified and as directed for the following: - |
| 23 | One light point controlled by one 6 Amps one way switch. |
| 24 | One ceiling Fan, Exhaust Fan point controlled by one 6 Amps switch. |
| 25 | One 3 Pin 6 Amps socket point on the independent board. |
| 26 | All as per above Item No 20.00 but with 2.5 Sqmm cable for 16 Amp switch socket out let point on independent board including 2.5 Sqmm PVC insulated unsheathed cable multistranded with copper conductor earthing continuity conductor all as directed and specified by Engr-in-charge. |
| 27 | Supply & Fix modular switch1 way 6A, 1 module complete all as specified and as directed. |
| 28 | Supply & Fix modular switch1 way 16A, 1 module complete all as specified and as directed. |
| 29 | Supply & Fix socket out let 6A 2/3 on combined 2 module complete all as specified and as directed. |
| 30 | Supply & Fix socket out let 6A/16A-2/3 pin combined 2 module complete all as specified and as directed. |
| 31 | Supply & Fix ceiling rose surface backlite 65x50mm 3 terminals complete complete all as specified and as directed. |
| 32 | Supply & Fix modular white cover plate with frame, 3 module complete all as specified and as directed. |
| 33 | Supply & Fix modular white cover plate with frame, 4 module complete all as specified and as directed. |
| 34 | Supply & Fix modular white cover plate with frame, 6 module complete all as specified and as directed. |
| 35 | Supply & Fix metal flush box 3 module complete all as specified and as directed. |
| 36 | Supply & Fix metal flush box 4 module complete all as specified and as directed. |
| 37 | Supply & Fix metal flush box 6 module complete all as specified and as directed. |
| 38 | Supply and fixing LED lights fitting 1x 20 W, 220V, AC decorative box type with driver, holder including LED tube light connecting up with three core flexible copper conductor cable of suitable size from ceiling rose complete. |
| 39 | Supply & Fix sheet metal enclosure MCB DB VTPN double door 4 way suitable for 415 V with 200 amps rated bus bar including flushed on walls and making good disturbed surfaces including taking down the old DB complete all as specified and as directed. |
| 40 | Supply and fix sheet metal enclosure distribution board SPN, 8 ways 240 volts, with 200 amps rated bus bar, with IP 43 protection and double door, suitable for mounting MCBs all as specified and as directed including taking down old MCB DB complete. |
| 41 | Supply and fix MCB single pole, 240 volts, 5 to 32 Amps, all as specified and as directed. |
| 42 | Supply and fix MCB single pole and neutral, 240 volts, 5 to 30 Amps, all as specified and as directed. |
| 43 | Supply and fix MCCB 16 KA , 415 volts,100 Amps,4 pole all as specified and as directed. |
| 44 | Material and labour for Cutting chases, pinning in. making good to facings where required and pointing in cement mortar 1:3 to ends or edges of landings, steps, cills, sunshades, shelves, lintels, etc. and cutting chases for concealed water tubing or concealed conduit wiring, etc., and making good, cutting not exc 10 cm girth in brick wall all as directed. |
| 45 | Supply and fixing LED luminaire 600 mm x 600 mm,35/36 watt, 220 V AC recessed type with high efficiency PMMA diffuser soft glare free light complete with driver, holders & LED lamp suitable for roof ceiling including connecting up with driver three core flexible copper conductor cables of suitable size complete all as specified and as directed. |
| 46 | Schedule of Credit Please Enable Macros to View BoQ information |
AI Tender Summary
Tender Timeline
Jul 04, 2026
11:30 IST
Tender Published
Tender notice published.
CompletedAug 01, 2026
17:00 IST
Bid Submission Deadline
Online submission via eProcurement portal.
Upcoming · 21 daysAug 03, 2026
Bid Opening Date
Technical bids will be opened and evaluated.
Upcoming · 23 daysTender Documents
Download All (ZIP) ↓
Disclaimer
We takes all possible care for accurate & authentic tender information. However users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender