Tender For Comprehensive B&R Repair/ Replacement And Other Works At Age(I), Stn Hq And Fpo At Sharifabad Mil Stn Under Age(I) Cif(K)
Tender Value
10 Lakhs
Estimated cost
Bid Submission
25 Jul 2026
16 days left
EMD
20000
Bank guarantee accepted
Document Fee
500
Non-refundable
Tender Type
Online
Tender Overview
Organization
Tender ID
Competition Type
NCB
Bidding Type
Tender
Location / State
Srinagar → Jammu and Kashmir
EMD Exemption
Not Available
Quantity
Not Available
Website
Contact Person
Address
Project Description
Tender for Comprehensive B&R Repair/ Replacement And Other Works At Age(I), Stn Hq And Fpo At Sharifabad Mil Stn Under Age(I) Cif(K)
BOQ
| Sl. No. | Item Description |
| 1 | Demolition of cement concrete un reinforced in ground floors and pavings not exceeding 15cm thickness (below or above ground level), complete all as specified and as directed by the Engineer-in-Charge. |
| 2 | Dismantling floor, hearth or wall tiling including cement mortar bedding removing serviceable tiles to store and rubbish off the premises. |
| 3 | Taking down cement plastering on stone wall/brick wall etc including racking out of joints hacking for key scrubbing down with water etc. |
| 4 | M&L 15mm thick rendering on fair faces of wall in CM 1:6 on brick/concrete surface and finishing the surface even and smooth with out using extra cement. |
| 5 | M&L 15mm thick rendering on fair faces of wall in CM 1:4 on brick/concrete surface and finishing the surface even and smooth with out using extra cement. |
| 6 | M&L for non skid ceramic coloured tiles 1st quality 7 to 8mm thick, (square/ rectangular), area of each tile exceeding 0.06sqm, but not exceeding 0.11sqm as in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tiles, laid over and including 15mm thick screed bed or bedding layer in cement mortar 1:6, complete all as specified and as directed by the Engineer-in-Charge.Note: Colour and shade of tiles shall be approved by AGE(I) and contractor shall not have any claim whatsoever on this account. |
| 7 | M&L for glazed ceramic tiles, coloured, of size 350mm x 250mm/450 mm x 350mm, thickness not less than 7mm as in vertical surfaces such as skirting/dado etc, set and jointed in neat cement slurry and pointed with white cement mixed with pigment to match the shade of tile, fixed over and including 10mm thick rendering (bedding layer) on brick/concrete surface in cement mortor 1:4, complete all as specified and as directed by the Engineer-in-Charge.Note: Colour and shade of tiles shall be approved by AGE(I) and contractor shall not have any claim whatsoever on this account. |
| 8 | M&L for Vitrified Ceramic tiles (Light shade/ Double charged/ Ultra charged) 10 mm thick (square/ rectangular) polished, area of each tiles not exceeding 0.36 sqm, as in floor, set and jointed in neat cement slurry and pointed in white or coloured cement to match the surface over 15mm thick screed bed in cement mortar 1:6, complete all as specified and as directed by the Engineer-in-Charge.Note: Colour and shade of tiles shall be approved by AGE(I) and contractor shall not have any claim whatsoever on this account. |
| 9 | M&L for Chequered cement concrete tiles of size 20 cm x 20 cm x 25 mm/ 30cm x 30cm x 25mm thick set, jointed and pointed in neat cement slurry in floors, paths etc, with grey cement and pigment, laid over and including 15mm thick screed bed or bedding layer in cement mortar 1:6, complete all as specified and directed by Engineer-in-Charge. |
| 10 | M&L for Plain cement concrete, 1:2:4, type B-1 using 20mm graded crushed stone aggregate, 25mm thick, as in levelling course of flooring, complete all as specified and as directed by the Engineer-in-Charge. |
| 11 | M&L for cement concrete 1:2:4 type B-1 using 20 mm graded stone aggregate as in copings, weathering, slightly rounded or chamfered angles and throating, complete all as specified and as directed by the Engineer-in-Charge. |
| 12 | Dismantiling of water tanks of capacity exc 250 & n exc 500 ltrs including all necessary fittings complete. |
| 13 | S&F 500 ltrs PVC rotational moulded polyethylene water storage tanks triple layer made (cylindrical vertical with closed top ) hoisted and fixed in position all as specified in SSR part-I |
| 14 | S&F 32 mm dia PPP-R gate valves (Brass inserted) as per requirment of the site complete all as specified. |
| 15 | S&F 15mm ball brass vlaves, high pressure, with polythene float and flynut complete, screwed for iron pipe or brass ferrule and fixed, complete all as specified. |
| 16 | S&F in repair Vitreous china wash hand basin (550X400mm) white, flat back excluding taps, including brackets & 32mm waste coupling complete all as specifed and directed. |
| 17 | S&F in repairs Vitreous Chinaware squatting pan, orissa pattern size 580mm x 440mm with integral foot rests any type, white and Size 110 x 110 PVC ‘S’ trap, front or back inlet, including provision of lime/cement concrete, and making good to floors (exclusing flushing cistern and pipe), complete all as specified and directed by the Engineer-in-Charge. |
| 18 | S&F 10 Litre PVC valveless syphonic action flushing cistern low level white with inlet ball valve, float and handle including brackets and flush pipe of polyethylene of low or high density or PVC 32 mm dia for low level cistern. |
| 19 | S&Fin repair 15mm dia fancy type chromium plated Bib taps cast copper alloy with crutch or butterfly handle screwed down, screwed for iron pipes or for brass ferrule |
| 20 | S&F 15mm dia stop valves/angle valve chromium plated, fancy type with long shank and cup screwed down, high pressure with crutch or butterfly handle, screwed both ends for iron pipe or for unions as specified . |
| 21 | Supply and fix 15mm dia brass CP mixer fancy type chromium plated for mixing hot and cold water screwed down for iron pipe . |
| 22 | Dismantling plain or corrugated steel sheeting, any gauge, thickness, including Nainital or similar pattern roof coverings. |
| 23 | S&F Pre- painted galvalume aluminum zinc coating GI based corrugated steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws complete all as specified and directed. |
| 24 | S & F Pre-painted galvalume aluminium zinc coating GI based plain steel sheet 0.50 mm thick of any colour having tensile strength of 550 Mpa as in ridges, fixed with self tapping screws, complete all as specified and directed. |
| 25 | Material and labour for preparation of new plastered surfaces of walls and applying two coats of oil bound distemper over a coat of primer, complete all as specified. |
| 26 | Material and labour for old painted surfaces after complete removal of existing treatment and applying two coats of oil bound distemper over a coat of chalk whiting, complete all as specified. |
| 27 | Material and labour for preparation of new plastered surfaces of walls and applying two coats of cement based paint over a coat of alkali resistant primer, complete all as specified. |
| 28 | S&F Anodised aluminium frame (powder coated minimum thickness of powder coating 50 micron) for doors, windows, partition wall with one or more rebates including joining cleat for fixing, rubber packing, anodised aluminium snap on beading for fixing glass panes in frame etc complete all as specified and directed. |
| 29 | S&F Anodised aluminium (powder coated minimum thickness of powder coating 50 micron) door shutters, powder coated of any colour aluminium section weighing 0.55 kg/m including necessary joining cleats, glazing clips, rubber neoprene packing, handles 2 Nos in each door, anodised aluminum snap beading screws etc., complete all as specified and directed by the Engineer-in-Charge. |
| 30 | S&F Anodised aluminium (powder coated minimum thickness of powder coating 50 micron) window, ventilator shutters fixed type withour sash bars, aluminium section weighing 0.55 kg/m including necessary joining cleats, glazing clips, rubber neoprene packing, anodised aluminum snap beading, screws etc., complete all as specified and directed by the Engineer-in-Charge. |
| 31 | S&F brass mortice lock, vertical type 4 levers,, size 100 mm, complete all as specified and directed by the Engineer-in-Charge. |
| 32 | M&L 4mm thick aluminium composite sheet with decorative colour and fixed with screw or aluminium beading to aluminium frame complete all as specified and as directed by the Engineer-in-Charge. |
| 33 | S&F plain sheet glass, 4 mm thick, selected quality and glazing with oil putty in squares exceeding 0.5 Sqm in each pane complete all as specified and as directed by the Engineer-in-Charge. |
| 34 | S&F door closer hydraulically regulated, designation No. 2, universal type, suitable for door shutters of 701 to 850 mm in width and of weight between 36 to 60 kg and fixed, complete all as specified and as directed by the Engineer-in-Charge. |
| 35 | Dismantling boarding/ false ceiling of any description, fixed in any position with nails, complete all as specified and directed by the Engineer-in-Charge. |
| 36 | S&F GI frame work size of grid 605 x 605 mm for seamless ceiling comprising of GI perimeter channel 0.55mm thick with two unequal flanges of 20 and 30mm and web of 27mm fixed to surrounding wall using nylon sleeves and screws at 450mm centre to centre/intermediate channel 0.9mm thick having two equal flanges of 15mm each and web of 45mm suspended from sofit at approx 900 mm centre to centre with GI cleat and steel expansion fasterner with and including ceiling section (not exc 1.2m length) of 0.55mm thickness having kurled web of 50mm and flange of 26mm each with lips of 10.5mm fixed to the intermediate channel with connecting clips acress the intermediate channel at 457mm centre to cnetre including hangers 6mm dia.GI (upto 1200mm length) adjusting level fixed tp roof slabs by means of ceiling cleats made out of GI flat 40 x 3mm size 60mm ling and expansion hold fasterner 12.5mm dia 40mm long including S&F 8mm thick non asbestos fibre cement building boards fixed or laid/inserted to timber/GI/ Aluminium frame work, complete all as specified and directed by Engineer-in-Charge. |
| 37 | S&F 2nd class soft wood boarding, 15mm thick, as in wall panelling, plain one side and edges tongued and grooved or rebated, fixed with nails in any situation including french polishing on surface of any description width or girth including cleaning and preparing the surface including a coat of wood filler on new works with two or more coat upto satification of Engr-In-Charge. |
| 38 | Note :- An amount of Rs. Rs 19,550.00 on account of credit schdule for Sch 'A' Part-II Shall be deducted from the total amount of BOQ to arrive at the contract sum. Please Enable Macros to View BoQ information |
AI Tender Summary
Tender Timeline
Jul 04, 2026
11:30 IST
Tender Published
Tender notice published.
CompletedJul 25, 2026
17:00 IST
Bid Submission Deadline
Online submission via eProcurement portal.
Upcoming · 16 daysJul 27, 2026
Bid Opening Date
Technical bids will be opened and evaluated.
Upcoming · 18 daysTender Documents
Download All (ZIP) ↓
Disclaimer
We takes all possible care for accurate & authentic tender information. However users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender